Particle size distributions of oxidative potential of ... - ACS Publications

1. Particle size distributions of oxidative potential of lung-deposited. 1 particles – assessing contributions from quinones and water-soluble. 2 me...
1 downloads 4 Views 751KB Size
Subscriber access provided by UNIVERSITY OF THE SUNSHINE COAST

Ecotoxicology and Human Environmental Health

Particle size distributions of oxidative potential of lung-deposited particles – assessing contributions from quinones and water-soluble metals Yan Lyu, Huibin Guo, Tiantao Cheng, and Xiang Li Environ. Sci. Technol., Just Accepted Manuscript • Publication Date (Web): 02 May 2018 Downloaded from http://pubs.acs.org on May 2, 2018

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 23

Environmental Science & Technology

1

Particle size distributions of oxidative potential of lung-deposited

2

particles – assessing contributions from quinones and water-soluble

3

metals

4 5

Yan Lyu1, Huibin Guo1, Tiantao Cheng1 and Xiang Li*, 1, 2

6 7

1

8

P.R. China

9

2

10

Department of Environmental Science & Engineering, Fudan University, Shanghai 200438,

Shanghai Institute of Pollution Control and Ecological Security, Shanghai 200092, P.R.

China

11 12

Correspondence to: Xiang Li ([email protected])

13

*Corresponding author.

14 15

ABSTRACT

16

Redox-active species in ambient particulate matter (PM) cause adverse health effects through

17

the production of reactive oxygen species (ROS) in the human respiratory tract. However,

18

respiratory deposition of these species and their relative contributions to oxidative potential

19

(OP) have not been described. Size-segregated aerosols were collected during haze and non-

20

haze periods using a MOUDI sampler at an urban site in Shanghai to address this issue.

21

Samples were analyzed for redox-active species content and PM OP. The average

22

dithiothereiol (DTT) activity of haze samples was approximately 2.4-fold higher than that of

23

non-haze samples and significantly correlated with quinone and water-soluble metal

24

concentrations. The size-specific distribution data revealed that both water-soluble OP DTT v

25

(volume-normalized OP quantified by DTT assay) and OPDTT (mass-normalized OP) were m

26

unimodal, peaking in 0.56–1 µm and 0.1–0.32 µm, respectively, due to contributions from

27

accumulation-mode quinones and water-soluble metals. We further estimated that transition

28

metals (mainly copper and manganese) contributed 55±13% of the DTT activity, while

29

quinones accounted for only 8±3%. Multiple-path particle dosimetry (MPPD) calculations

30

estimated that OP deposition in the pulmonary region was mainly from accumulation-mode

1

ACS Paragon Plus Environment

Environmental Science & Technology

31

transition metals despite quinones having the highest DTT activity. This behavior is primarily

32

attributed to the deposition efficiency of transition metals in the pulmonary region being

33

approximately 1.2-fold greater than that of quinones. These results reveal that accumulation-

34

mode transition metals are significant contributors to the OP of deposited water-soluble

35

particles in the pulmonary region of the lung.

36

INTRODUCTION

37

Many epidemiologic studies have shown the link between exposure to particulate matter (PM)

38

and increases in adverse respiratory1-3 and cardiovascular outcomes.4-6 Recently, mounting

39

evidence indicates that the deposition of PM in the human respiratory tract (RT) can cause

40

adverse health effects via oxidative stress through the overproduction of reactive oxygen

41

species (ROS).7-9 These ROS could be either carried by the PM themselves10 or generated via

42

interactions between particle-bound redox-active components and antioxidants (i.e., ascorbate,

43

reduced glutathione, uric acid, and vitamin E) in lung lining fluid.11

44

The dithiothreitol (DTT) assay is a widely used cell-free approach for the measurement of

45

ROS generation capacity, the so-called oxidative potential (OP).12 In the DTT assay, redox-

46

active species oxidize DTT to its disulfide form and then transfer an electron to dissolved

47

oxygen, generating superoxide radical (O2·-) that can then form other ROS (i.e., ·OH). Many

48

chemical species in particles are considered redox-active, including transition metals,13

49

quinones,12, 14 humic-like substances (HULIS),15 soot or black carbon,16, 17 environmentally

50

persistent free radicals (EPFRs)18, 19 and secondary organic aerosols (SOAs) from biogenic

51

precursors.20 Chamber studies suggested that many compounds in PM other than the

52

quinones that were identified and measured in ambient atmosphere drive its OP.21 Previous

53

studies on the contributions of chemical species to the OP of ambient particles are rather

54

limited. Charrier and Anastasio13 reported that as much as 80% of DTT activity could be

55

ascribed to transition metals (especially Cu and Mn) based on hypothetical PM2.5 and data

56

from the literature. The major redox-active components of water-soluble PM were found to

57

be HULIS, which contained compounds such as quinones.15 Verma et al.14 showed that

58

quinones only accounted for ~10% of water-soluble DTT activity of PM2.5 in Atlanta, USA.

59

The varying of redox-active components with particle size indicates that the OP of PM is

60

size-dependent. Particle size partly affects deposition in the human RT. Small particles, along

61

with various chemicals, can penetrate the lower (deeper) regions of the human RT (i.e., the

62

pulmonary region), and they are very harmful due to the difficulties in clearing them and

63

their easy access to blood.22 Ultrafine particles are particularly difficult to clear because they 2

ACS Paragon Plus Environment

Page 2 of 23

Page 3 of 23

Environmental Science & Technology

64

avoid phagocytosis by alveolar macrophages and thus enter the pulmonary interstitial sites,

65

inducing pulmonary inflammation. 23 In contrast, coarse particles are probably inhibited by

66

rhinothrix via impaction processes and are more likely to deposit in upper regions of the RT

67

(nasal area). Some researchers have shown that metals in particles deposited in the nasal

68

region could cross synapses in the olfactory bulb and migrate via secondary olfactory neurons

69

to the distant nuclei of the brain, 24 causing olfactory deficits25 and brain lesions. 26

70

There is a wide array of studies on the size-depend OP all over the world,27-30 but such

71

information is lacked to an extent in China. In this study, size-resolved ambient PM was

72

collected during haze and non-haze periods using a Micro-Orifice Uniform Deposit Impactor

73

(MOUDI) sampler at an urban site in Shanghai, China. We systematically examined the

74

contributions of quinones and water-soluble metals to the size-dependent water-soluble OP of

75

ambient PM in combination with measurements of the OP of pure quinones and metals.

76

Furthermore, the relative importance of quinones and metals to the respiratory deposition of

77

aerosol water-soluble OP is illustrated using a multiple-path particle dosimetry (MPPD)

78

model in this study.

79

MATERIALS AND METHODS

80

Sample Collection. Size-resolved particle samples were collected in urban Shanghai, China,

81

during haze and non-haze periods using a MOUDI (110R, MSP Corp., Shoreview, MN). The

82

impactor was placed on the rooftop of teaching building No. 4 at the Handan Campus of

83

Fudan University (31.30 °N, 121.50 °E) with a flow rate of 30 L/min from January to May,

84

2016. Details on the sampling site can be found in Lyu et al. 31 The MOUDI fractionates

85

particles at the aerodynamic cutoff sizes of 0.056, 0.1, 0.18, 0.32, 0.56, 1.0, 1.8, 3.2, 5.6, 10,

86

and 18 µm. Particles were collected on prebaked (under 500 °C for 4 h) quartz fiber filter

87

(QFF, 47 mm, Whatman QMA) for a continuous 24 and 48 h during haze and non-haze

88

periods, respectively, both beginning at 9 a.m. Four MOUDI sample batches were collected

89

during haze periods (January 15 and 18, March 5 and 18, 2016), and the other four batches

90

were collected during non-haze periods (April 22 and May 3, 12 and 22, 2016). Three field

91

blanks were included. The particle mass loadings were determined by the difference in the

92

filter weight before and after the sampling and ranged from 0.30 to 1.26 mg. All data were

93

later blank corrected with the combined average of the three field blanks. The loaded filters

94

were immediately sealed in Petri dishes and stored in a freezer (−24 °C) until further analysis.

95

The samples were analyzed for the content of quinones and water-soluble metals and water-

96

soluble DTT activity (Figure S1). 3

ACS Paragon Plus Environment

Environmental Science & Technology

Page 4 of 23

97

Chemical analysis. One-half of the quartz filter was used for quinone determination using

98

GC-MS/MS (7890A-7000B, Agilent Technologies, Wilmington, DE). These quinones

99

included

1,2-naphthoquinone (2H-14NQ),

(12NQ),

1,4-naphthoquinone

(14NQ),

5-hydroxy-1,4-naphthoquinone

2-hydroxy-1,4-

100

naphthoquinone

(5H-14NQ),

9,10-

101

anthracenequinone (AQ), 9,10-phenanthraquinone (PQ) and benz(a)anthracene-7,12-quinone

102

(BAQ). Briefly, one-half of each filter was cut into pieces and extracted twice (ultrasonicated

103

each time for 30 min) using 4 mL of dichloromethane (DCM) as solvent. The combined

104

extracts were filtered using pore syringe filters (PTFE, 0.45 µm) and subsequently rinsed

105

with 2 mL of DCM. To enhance the sensitivity and stability of GC-MS/MS measurements,

106

the target quinones were converted to their diacetyl derivatives using the method used by

107

Delgado-Saborit et al. 32 The results showed that major quinones (12NQ, 14NQ, PQ, AQ, and

108

BAQ) can be successfully derivatized at low concentrations (those expected in ambient air).

109

The detailed derivatization method and GC-MS/MS conditions for analyzing acetylated

110

derivatives are included in supporting information (SI). In addition, a recovery test was

111

conducted after each sample batch using freshly baked QFF spiked with 1 mL of a quinone

112

stock solution. The average recovery of the derivatized quinones was 103±14%. The reported

113

concentrations were all corrected by the blank and recovery values.

114

For determining water-soluble metals, we cut one-quarter of the filter and sonicated it in 2

115

mL of DI water for 1 h with an ultrasonic cleanser. After sonication, the extracts were filtered

116

using PTFE 0.45-µm pore syringe filters. HNO3 (4%) was then added to produce a final

117

volume of 10 mL. Here, we focus on Cu, Mn, and Fe as they are common transition metals

118

linked to aerosol toxicity.

119

potential ship emissions may influence the environment. 35 Vanadium has been suggested to

120

indicate ship traffic emission in Shanghai36 and is thus also quantified in this study. The

121

signal response of a series of standard metal solutions (0.1-100 ppb) was recorded by 7900

122

ICP-MS (Agilent Technologies, Wilmington, DE). The determination coefficient (R2) of the

123

standard calibration curves ranged from 0.9991 to 0.9997 (N = 6) for the target metals. The

124

background equivalent concentration (BEC) values (4% HNO3 blank) for Cu, Mn, Fe and V

125

were 0.034, 0.0032, 0.31 and 0.0008 ppb, respectively. A 20-ppb internal standard of

126

scandium (Sc) and germanium (Ge) was added to all samples and standards to monitor

127

analytical drift. The recoveries of the target metals ranged from 82 to 117%. Target metals

128

were found in blank filter extracts (Cu: 0.25 ppb, Mn: 0.32 ppb, Fe: 10.8 ppb, and V: 0.03

33, 34

In addition, Shanghai has the largest port worldwide, and

4

ACS Paragon Plus Environment

Page 5 of 23

Environmental Science & Technology

129

ppb). The reported concentrations for ambient PM samples were all blank- and recovery-

130

corrected.

131

Oxidative potential. The remaining one-quarter of the filter was used for the OP

132

measurement. The loaded filters were cut and sonicated in DI water for 1 h, which was then

133

filtered with 0.45-µm syringe filters. The dithiothreitol (DTT) assay adopted in this study

134

mainly follows that the procedure used in Cho et al. 37 We measured DTT consumption rates

135

of both samples and pure quinones and metal solutions. The details can be found in SI. Light

136

in the work space was excluded as much as possible (e.g., experiments were performed with

137

the lights off, and vials were covered with aluminum foil when not in use) because both DTT

138

and DTNB are sensitive to light. 38. Blank tests showed that a negligible amount of DTT was

139

consumed in buffer solutions (