Perovskite for Efficient Electrocatalytic Oxygen ... - ACS Publications

Dec 31, 2018 - ABSTRACT: Oxygen vacancies (OVs) can improve catalytic activities in oxygen evolution reaction (OER). Although considerable effort has ...
0 downloads 0 Views 936KB Size
Subscriber access provided by University of Kansas Libraries

Letter

Engineering Oxygen Vacancies into LaCoO3 Perovskite for Efficient Electrocatalytic Oxygen Evolution Yao Lu, Aijing Ma, Yifu Yu, Rui Tan, Chengwei Liu, Peng Zhang, Dan Liu, and Jianzhou Gui ACS Sustainable Chem. Eng., Just Accepted Manuscript • DOI: 10.1021/ acssuschemeng.8b05717 • Publication Date (Web): 31 Dec 2018 Downloaded from http://pubs.acs.org on January 2, 2019

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

Engineering Oxygen Vacancies into LaCoO3 Perovskite for Efficient Electrocatalytic Oxygen Evolution Yao Lu,† Aijing Ma,†,‡ Yifu Yu,§ Rui Tan,† Chengwei Liu,† Peng Zhang,† Dan Liu*,†, and Jianzhou Gui*,†,‡ †

Tianjin Key Laboratory of Green Chemical Technology and Process Engineering, School of Chemistry & Chemical Engineering, Tianjin Polytechnic University, Binshui West Road 399, Tianjin, 300387, P. R. China ‡ State Key Laboratory of Separation Membranes and Membrane Processes, School of Material Science and Engineering, Tianjin Polytechnic University, Binshui West Road 399, Tianjin, 300387, P. R. China § Department of Chemistry, School of Science, and Tianjin Key Laboratory of Molecular Optoelectronic Science, Tianjin University, Yaguan Road 135, Haihe Education Park, Tianjin, 300072, P. R. China *E-mail: [email protected] (LIU); [email protected](GUI)

ABSTRACT: Oxygen vacancies (OVs) can improve the catalytic activities in oxygen evolution reaction (OER). Although considerable effort has been devoted to increasing the OVs concentration in the electrocatalysts, limited OVs have been created by current techniques so far. Here, we, for the first time, engineered (i.e. created) abundant OVs into perovskites by element doping and plasma treatment. The results revealed that more OVs were manufactured by combination Sr doping with Ar plasma treatment, leading to improved OER activity and high stability of LaCoO3 perovskite. The La1-xSrxCoO3-δ (x=0.3) sample with Ar plasma treatment (denoted as Sr-0.3-p) showed high OER activity and stability due to the existence of rich OVs, which provided large amount as well as high intrinsic activity of active sites in OER. The combination of two OVs-creating techniques provides an efficient strategy to develop OVs-rich catalysts for various applications. 1

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

KEYWORDS: OER; perovskite; Sr doping; plasma treatment; oxygen vacancies. INTRODUCTION The global energy crisis and environmental issue are driving researchers to develop renewable and clean energy to substitute the traditional fossil fuels.1 Water electrolysis is considered as one of the eco-friendly and sustainable methods to supply high-purity hydrogen energy. However, as a concomitant reaction of hydrogen production in water electrolysis, oxygen evolution reaction (OER) is undergoing the slow kinetics, which requires excess energy consumption and thus results in lower energy efficiency.2-4 The commercial OER catalysts, such as RuO2 and IrO25,6, are suffering from the difficulty of wide application because the noble-metal catalysts are precious and scarce. Therefore, it is urgent to develop inexpensive, efficient and stable OER catalysts as the substitution for noble-metal materials. During the past decades, transition metal-based oxides have been widely adopted as OER catalysts.7-9 Among them, perovskites have attracted more and more attention because of their cheap price, excellent structural stability and adjustable physical-chemical properties.10-18 Unfortunately, the OER performance of perovskites still needs to be further improved. It has been widely reported that oxygen vacancies (OVs) in transition metal-based oxides can efficiently improve their electrocatalytic 2

ACS Paragon Plus Environment

Page 2 of 15

Page 3 of 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

performance.19-21 For example, Wang et al. proved that OVs generated in transition metal oxides can improve the electronic conductivity of catalysts and create more active sites, enhancing the electrocatalytic activity for OER.19 Xie group demonstrated that the OVs could efficiently increase the reactivity of active sites and OER activity by decreasing the adsorption energy of H2O on the surface of catalysts.20 To date, various techniques have been developed to create OVs, including calcination treatment under controlled atmosphere,22 doping,19 nonstoichiometric synthesis24, and plasma treatment.14 Although significant progress has been made in the area of preparing OVs-rich electrocatalysts, present works mostly focused on the adoption of solely technique to create limited OVs. It is reasonable to expect that the combination of different OVs-creating techniques can manufacture abundant OVs and thus greatly enhance the OER ability of perovskite-type oxides. Herein, by choosing LaCoO3 perovskite as model OER catalysts, we created OVs in perovskites by adopting two techniques simultaneously. This should be the first time to adopt the combination strategy of creating OVs in perovskites, as far as we know. First, we introduced OVs through substitution lower valence Sr2+ ion for the La3+ ion. Then, the Ar plasma treatment technique was adopted to further manufacture OVs (Figure 1a). The results demonstrated that OVs originated from the combination of two different techniques can improve the OER performance of LaCoO3 3

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

perovskite. Moreover, the electrocatalysts with abundant OVs showed high stabilities. RESULTS AND DISCUSSION The obtained samples were firstly examined by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). It can be clearly seen that the average size decreased after the partial substitution Sr2+ cations for La3+ cations (Figure S1, Figure 1b). Moreover, the samples of Sr-0.3 and Sr-0.3-p showed similar size and crystalline structure (Figure S2), indicating that plasma treatment had little effect on the morphology of perovskites (Figure 1b,c). The smaller particle size would result in larger special surface areas (Table S1), which may benefit the electrochemical activity. The characterization of X-ray diffraction (XRD), depicted in Figure 1d, confirmed that the as-prepared samples presented a rhombohedral perovskite-type phase. Notably, it was observed that the diffraction peaks gradually shifted toward small diffraction angles with the increasing Sr2+ in perovskites (Figure 1e). This was ascribed to the successive replacement of smaller La3+ cation (rLa3+= 0.136 nm) by bigger Sr2+ cation (rSr2+= 0.144 nm), leading to the expansion of perovskite unit cell.25 Moreover, phase segregation in the form of SrCoOx (JCPDS 49-0692) started to be detected in Sr-0.5 sample, suggesting the limited Sr accommodation in La1-xSrxCoO3-δ perovskite lattice. In the spectra of Fourier Transform infrared spectroscopy (FT-IR), 4

ACS Paragon Plus Environment

Page 4 of 15

Page 5 of 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

the vibration peaks at 1465 and 859 cm-1 demonstrated the formation of carbonate species in the Sr-0.5 sample (Figure S3).26,27 Comparing with Sr-0.3, the diffraction peaks of Sr-0.3-p showed little change. It implied that Ar plasma treatment had a negligible effect on the bulk structure of the sample, which was in agreement with the result before.28

Figure 1. (a) Scheme for engineering (i.e. creating) OVs into LaCoO3 perovskite; SEM images of (b) Sr-0.3 and (c) Sr-0.3-p samples; (d) XRD patterns of La1-xSrxCoO3-δ perovskites; (e) Zoom-in of the patterns (d) in the 2θ range of 46.5o~48.5o

X-ray photoelectron spectroscopy (XPS) was adopted to characterize the concentration of OVs. As shown in Figure 2a, four peaks were 5

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

obtained after the deconvolution of O 1s spectra. The peaks at 528.4, 530.0, 530.9 and 532.0 eV can be assigned to the lattice oxygen species (O1), OVs (O2), the surface-adsorbed oxygen species or the hydroxyl groups (O3) and the surface-adsorbed water (O4),29-33 respectively. Table S2 listed the relative concentration of each oxygen species in perovskites, which was obtained from the area ratio of corresponding peak. It can be seen that both Sr doping and Ar plasma treatment can increase the concentration of OVs. The sample of Sr-0.3-p exhibited higher OVs concentrations than the others, suggesting that it is an effective way to engineer (i.e. create) more OVs by a combination of two OVs-creating techniques. The concentration of OVs in all the samples was further confirmed by oxygen temperature-programmed desorption (O2-TPD) measurements. Three main oxygen desorption peaks were seen in the profiles (Figure 2b), which can be ascribed to physical adsorption oxygen (below 450 oC), chemical adsorption oxygen (450-700 oC) and the lattice oxygen in perovskites (above 700 oC).34-37 In O2-TPD profile, the integral area of desorption peak can reflect the concentration of corresponding specials. Previous studies have proven that chemical adsorption oxygen was closely related to the OVs.38-40 The integral area of chemical adsorbed oxygen in TPD profiles were calculated following the order: Sr-0.5 > Sr-0.3-p > Sr-0.3 > Sr-0.1 > Sr-0 (Table S3). Notably, the highest content of chemical adsorbed oxygen in Sr-0.5 may arise from the 6

ACS Paragon Plus Environment

Page 6 of 15

Page 7 of 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

impurities (i.e., SrCoOx and carbonate species). All the aforementioned results prove more OVs can be readily created into LaCoO3 perovskite by the adoption of Sr doping and Ar plasma treatment together. It is predictable that the sample with a higher concentration of OVs will show better OER performance.

Figure 2. (a) XPS survey in O 1s region and (b) O2-TPD profiles of La1-xSrxCoO3-δ perovskites

The electrocatalytic OER performances of La1-xSrxCoO3-δ perovskites were measured in 1.0 M KOH (Figure 3). Potentials of reversible hydrogen electrode (RHE) with I-R compensation were adopted in the liner sweep voltammetry (LSV) polarization curves. As shown in Figure 3a, compared to LaCoO3, the Sr-doped catalysts required lower onset potentials and overpotentials relative to the same current densities. Among them, Sr-0.3-p catalyst exhibited the best OER activity, for which the onset potential and overpotential at 10 mA cm-2 were 120 mV and 326 mV, respectively. The Tafel plots (Figure 3b) and Nyquist impedance plots (Figure 3c) were utilized to reflect OER kinetics of catalysts. 7

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Similar to the LSV results, Sr-0.3-p showed a smaller Tafel slop (70.8 mV dec−1) and a lower impendence (39.3 Ω) compared with the others, implying faster reaction kinetics. It should be mentioned that the onset potentials, the overpotentials under the same current densities, the Tafel slopes and the charge-transfer resistance of La1-xSrxCoO3-δ catalysts followed the order: Sr-0.3-p < Sr-0.3 < Sr-0.5 < Sr-0.1 < Sr-0, which is in inverse order to that of the concentration of OVs (Figure 2a). It is suggested that OVs played a dominant role in OER performance. The electrochemical stabilities of Sr-0.3 and Sr-0.3-p catalysts were tested by LSV curves initial and after 1000 cycles as well as chronopotentiometric curves. As shown in Figure 3d and its inset, Sr-0.3-p exhibited excellent stability for OER as well as Sr-0.3. Besides, the morphology of Sr-0.3-p kept unchanged after OER performances (Figure S4).

8

ACS Paragon Plus Environment

Page 8 of 15

Page 9 of 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

Figure 3. (a) Polarization curves, (b) Tafel slopes and (c) EIS spectra of La1-xSrxCoO3-δ perovskites (in the top-right corner: EIS fitting model, where the symbols of Rs, Cd and Rct refer to the resistance of electrolyte, capacitive and charge-transfer, respectively.), (d) LSV curves of Sr-0.3 and Sr-0.3-p catalysts initial and after 1000 cycles (inset: chronopotentiometric curves of Sr-0.3 and Sr-0.3-p catalysts at 10 mA cm-2)

Figure 4. (a) Measurements of electrochemical double-layer capacitance at 0.975 V and (b) Current densities per ECSA vs. potential for Sr-0, Sr-0.3 and Sr-0.3-p samples 9

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Electrochemically active surface areas (ECSA) of catalysts, which were calculated from electrochemical double-layer capacitance at 0.975 V, have been measured in order to account for the high activity of Sr-0.3-p catalyst in OER (Figure 4a and Figure S5). It was shown that the ECSA of Sr-0.3-p was 60 cm-2ECSA, which was higher than that of Sr-0.3 (52.5 cm-2ECSA) and Sr-0 (7.5 cm-2ECSA) catalysts. The results indicated that more active sites existed in Sr-0.3-p due to the massive OVs. Figure 4b exhibited the LSV curves with the current density normalized to ECSA. Interestingly, Sr-0.3-p still showed better performance than Sr-0.3 and Sr-0 catalysts, revealing the superior intrinsic activity of active sites in the Sr-0.3-p catalyst. A conclusion can be drawn from the above results that the catalyst treated by Sr doping and the following Ar plasma treatment can not only create more OVs in LaCoO3 perovskite but also increase the intrinsic activity of active sites, resulting in the improvement of OER activity. CONCLUSION In summary, we have successfully created more OVs in LaCoO3 perovskite by Sr doping and Ar plasma treatment. By the combination of two techniques, we achieved the outstanding OER performance due to the existence of abundant OVs, which acted as active sites and showed high intrinsic activity. This finding offers us a simple and effective strategy to create OVs and thus improve the OER activity. Moreover, the proposed 10

ACS Paragon Plus Environment

Page 10 of 15

Page 11 of 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

strategy of combining different OVs-creating techniques and the immense potential of transition metal-based oxides will provide new insights into understanding the structure-property relationships of catalysts and explore more widespread application for OVs-rich materials. ASSOCIATED CONTENT Supporting Information The Supporting Information is available free of charge on the ACS Publications website at DOI: xx.xxxx/ acssuschemeng.xxxxxxx. Experimental section, SEM images, TEM and HRTEM images, FT-IR spectra, CV curves and Table S1-S3 (PDF). AUTHOR INFORMATION Corresponding Author *E-mail:[email protected] (Liu); [email protected] (Gui) Notes The authors declare no competing financial interest. ACKNOWLEDGMENTS The authors acknowledge the financial support from the National Natural Science Foundation of China (Grant No. 21706191 and 21576211), China Postdoctoral Science Foundation (Grant No. 2017M610164), Program for Tianjin Innovative Research Team in Universities (Grant No.TD13-5031) and Tianjin 131 Research Team of Innovative Talents.

11

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 12 of 15

REFERENCES (1) Chu, S.; Majumdar, A. Opportunities, and challenges for a sustainable energy future. Nature 2012, 488 (7411), 294-303, DOI 10.1038/nature11475. (2) Staszak-Jirkovsky, J.; Malliakas, C. D.; Lopes, P. P.; Danilovic, N.; Kota, S. S.; Chang, K. C.; Genorio, B.; Strmcnik, D.; Stamenkovic, V. R.; Kanatzidis, M. G.; Markovic, N. M. Design of active and stable Co-Mo-Sx chalcogels as pH-universal catalysts for the hydrogen evolution reaction. Nat Mater. 2016, 15 (2), 197-203, DOI 10.1038/nmat4481. (3) Seitz, L. C.; Dickens, C. F.; Nishio, K.; Hikita, Y.; Montoya, J.; Doyle, A.; Kirk, C.; Vojvodic, A.; Hwang, H. Y.; Norskov, J. K.; Jaramillo, T. F. A highly active and stable IrOx/SrIrO3 catalyst for the oxygen evolution reaction. Science 2016, 353 (6303), 1011-1014, DOI 10.1126/science.aaf5050. (4) Reier, T.; Nong, H. N.; Teschner, D.; Schlögl, R.; Strasser, P. Electrocatalytic oxygen evolution reaction in acidic environments-reaction mechanisms and catalysts. Adv. Energy Mater. 2017, 7 (1), 1601275, DOI 10.1002/aenm.201601275. (5) Suen, N. T.; Hung, S. F.; Quan, Q.; Zhang, N.; Xu, Y. J.; Chen, H. M. Electrocatalysis for the oxygen evolution reaction: recent development and future perspectives. Chem. Soc. Rev. 2017, 46 (2), 337-365, DOI 10.1039/c6cs00328a. (6) Gong, M.; Dai, H. A mini review of NiFe-based materials as highly active oxygen evolution reaction electrocatalysts. Nano Res. 2014, 8 (1), 23-39, DOI 10.1007/s12274-014-0591-z. (7) Jasem, S. M.; Tseung, A. C. C. A potentiostatic pulse study of oxygen evolution on teflon-bonded nickel-cobalt oxide electrodes. J. Electrochem. Soc. 1979, 126 (8), 1353-1360, DOI 10.1149/1.2129276. (8) Zhang, R.; Zhang, Y.-C.; Pan, L.; Shen, G.-Q.; Mahmood, N.; Ma, Y.-H.; Shi, Y.; Jia, W.; Wang, L.; Zhang, X.; Xu, W.; Zou, J.-J. Engineering cobalt defects in cobalt oxide for highly efficient electrocatalytic oxygen evolution. ACS Catal. 2018, 8 (5), 3803-3811, DOI 10.1021/acscatal.8b01046. (9) Xu, H.; Shi, Z. X.; Tong, Y. X.; Li, G. R. Porous Microrod arrays constructed by carbon-confined NiCo@NiCoO2 core@chell nanoparticles as efficient electrocatalysts for oxygen evolution. Adv. Mater. 2018, 30 (21), 1705442, DOI 10.1002/adma.201705442. (10) Suntivich, J.; May, K. J.; Gasteiger, H. A.; Goodenough, J. B.; Shao-Horn, Y. A perovskite oxide optimized for oxygen evolution catalysis from molecular orbital principles. Science 2011, 334 (6061), 1383-1385, DOI 10.1002/chin.201211009. (11) Suntivich, J.; Gasteiger, H. A.; Yabuuchi, N.; Nakanishi, H.; Goodenough, J. B.; Shao-Horn, Y. Design principles for oxygen-reduction activity on perovskite oxide catalysts for fuel cells and metal-air batteries. Nat. Chem. 2011, 3 (7), 546-550, DOI 10.1038/NCHEM.1069. (12) Zhu, Y.; Zhou, W.; Chen, Z. G.; Chen, Y.; Su, C.; Tade, M. O.; Shao, Z. SrNb (0.1)Co(0.7)Fe(0.2)O(3-δ) perovskite as a next-generation electrocatalyst for oxygen evolution in alkaline solution. Angew. Chem., Int. Ed. 2015, 54 (13), 3897-3901, DOI 10.1002/ange.201408998. (13) Jung, J. I.; Jeong, H. Y.; Lee, J. S.; Kim, M. G.; Cho, J. A bifunctional perovskite catalyst for oxygen reduction

and

evolution.

Angew.

Chem.,

Int.

Ed.

2014,

53

(18),

4582-4586,

DOI

10.1002/ange.201311223. (14) Hardin, W. G.; Mefford, J. T.; Slanac, D. A.; Patel, B. B.; Wang, X.; Dai, S.; Zhao, X.; Ruoff, R. S.; Johnston, K. P.; Stevenson, K. J. Tuning the electrocatalytic activity of perovskites through active site variation and support interactions. Chem. Mater. 2014, 26 (11), 3368-3376, DOI 10.1021/cm403785q. (15) Chen, G.; Zhou, W.; Guan, D.; Sunarso, J.; Zhu, Y.; Hu, X.; Zhang, W.; Shao, Z. Two orders of magnitude enhancement in oxygen evolution reactivity on amorphous Ba 0.5Sr0.5Co0.8Fe0.2O3-δ 12

ACS Paragon Plus Environment

Page 13 of 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

nanofilms with tunable oxidation state. Sci. Adv. 2017, 3 (6), e1603206, DOI 10.1126/sciadv.1603206. (16) Chen, G.; Hu, Z.; Zhu, Y.; Chen, Z. G.; Zhong, Y.; Lin, H. J.; Chen, C. T.; Tjeng, L. H.; Zhou, W.; Shao, Z. Ultrahigh-performance tungsten-doped perovskites for the oxygen evolution reaction. J. Mater. Chem. A 2018, 6 (21), 9854-9859, DOI 10.1039/c8ta02864h.

(17) Chen, G.; Hu, Z.; Zhu, Y.; Gu, B.; Zhong, Y.; Lin, H.-J.; Chen, C.-T.; Zhou, W.; Shao, Z. A universal strategy to design superior water-splitting electrocatalysts based on fast in situ reconstruction of amorphous nanofilm precursors. Adv. Mater. 2018, 30 (43), 1804333, DOI 10.1002/adma.201804333. (18) Zhu, Y.; Chen, G.; Zhong, Y.; Chen, Y.; Ma, N.; Zhou, W.; Shao, Z. A surface-modified antiperovskite as

an

electrocatalyst

for

water

oxidation.

Nat.

Commun.

2018,

9

(1),

2326,

DOI

10.1038/s41467-018-04682-y. (19) Xu, L.; Jiang, Q.; Xiao, Z.; Li, X.; Huo, J.; Wang, S.; Dai, L. Plasma-engraved Co3O4 nanosheets with oxygen vacancies and high surface area for the oxygen evolution reaction. Angew. Chem., Int. Ed. 2016, 55 (17), 5277-5281, DOI 10.1002/anie.201600687. (20) Bao, J.; Zhang, X.; Fan, B.; Zhang, J.; Zhou, M.; Yang, W.; Hu, X.; Wang, H.; Pan, B.; Xie, Y. Ultrathin spinel-structured nanosheets rich in oxygen deficiencies for enhanced electrocatalytic water oxidation. Angew. Chem., Int. Ed. 2015, 54 (25), 7399-73404, DOI 10.1002/ange.201502226. (21) Cai, Z.; Bi, Y.; Hu, E.; Liu, W.; Dwarica, N.; Tian, Y.; Li, X.; Kuang, Y.; Li, Y.; Yang, X.-Q.; Wang, H.; Sun, X. Single-crystalline ultrathin Co3O4 nanosheets with massive vacancy defects for enhanced electrocatalysis. Adv. Energy Mater. 2018, 8 (3), 1701694, DOI 10.1002/aenm.201701694. (22) Chen, C.-F.; King, G.; Dickerson, R. M.; Papin, P. A.; Gupta, S.; Kellogg, W. R.; Wu, G. Oxygen-deficient BaTiO3−x perovskite as an efficient bifunctional oxygen electrocatalyst. Nano Energy 2015, 13, 423-432, DOI 10.1016/j.nanoen.2015.03.005. (23) Raabe, S.; Mierwaldt, D.; Ciston, J.; Uijttewaal, M.; Stein, H.; Hoffmann, J.; Zhu, Y.; Blöchl, P.; Jooss, C. In situ electrochemical electron microscopy study of oxygen evolution activity of doped manganite perovskites. Adv. Funct. Mater. 2012, 22 (16), 3378-3388, DOI 10.1002/adfm.201103173. (24) Zhu, Y.; Zhou, W.; Yu, J.; Chen, Y.; Liu, M.; Shao, Z. Enhancing electrocatalytic activity of perovskite oxides by tuning cation deficiency for oxygen reduction and evolution reactions. Chem. Mater. 2016, 28 (6), 1691-1697, DOI 10.1021/acs.chemmater.5b04457. (25) Rousseau, S.; Loridant, S.; Delichere, P.; Boreave, A.; Deloume, J. P.; Vernoux, P. La (1−x)SrxCo1−yFeyO3 perovskites prepared by sol–gel method: Characterization and relationships with catalytic properties for

total

oxidation

of

toluene.

Appl.

Catal.,

B

2009,

88

(3-4),

438-447,

DOI

10.1016/j.apcatb.2008.10.022. (26) Lavalley, J. C. Infrared spectrometric studies of the surface basicity of metal oxides and zeolites using

adsorbed

probe

molecules.

Catal.

Today

1996,

27

(3-4),

377-401,

DOI

10.1016/0920-5861(95)00161-1. (27) Ma, A.-J.; Wang, S.-Z.; Liu, C.; Xian, H.; Ding, Q.; Guo, L.; Meng, M.; Tan, Y.-S.; Tsubaki, N.; Zhang, J.; Zheng, L.-R.; Li, X.-G. Effects of Fe dopants and residual carbonates on the catalytic activities of the perovskite-type La0.7Sr0.3Co1−xFexO3 NOx storage catalyst. Appl. Catal., B 2014, 146, 24-34, DOI 10.1016/j.apcatb.2013.06.005. (28) Zhang, C.; Shi, Y.; Yu, Y.; Du, Y.; Zhang, B. Engineering Sulfur Defects, Atomic thickness, and porous structures into cobalt sulfide nanosheets for efficient electrocatalytic alkaline hydrogen evolution. ACS Catal. 2018, 8 (9), 8077-8083, DOI 10.1021/acscatal.8b02056. (29) Xue, Y.; Miao, H.; Sun, S.; Wang, Q.; Li, S.; Liu, Z. (La 1−xSrx)0.98MnO3 perovskite with A-site 13

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

deficiencies toward oxygen reduction reaction in aluminum-air batteries. J. Power Sources 2017, 342, 192-201, DOI 10.1016/j.jpowsour.2016.12.065. (30) Zhao, B.; Wang, R.; Yang, X. Simultaneous catalytic removal of NO x and diesel soot particulates over La1−xCexNiO3 perovskite oxide catalysts. Catal. Commun. 2009, 10 (7), 1029-1033, DOI 10.1016/j.catcom.2008.10.024. (31) Fierro, J. L. G. Structure and composition of perovskite surface in relation to adsorption and catalytic properties. Catal. Today 1990, 8 (2), 153-174, DOI 10.1016/0920-5861(90)87016-v. (32) Hernández, W. Y.; Tsampas, M. N.; Zhao, C.; Boreave, A.; Bosselet, F.; Vernoux, P. La/Sr-based perovskites as soot oxidation catalysts for Gasoline Particulate Filters. Catal. Today 2015, 258 (2), 525-534, DOI 10.1016/j.cattod.2014.12.021. (33) Arandiyan, H.; Dai, H.; Deng, J.; Liu, Y.; Bai, B.; Wang, Y.; Li, X.; Xie, S.; Li, J. Three-dimensionally ordered macroporous La0.6Sr0.4MnO3 with high surface areas: active catalysts for the combustion of methane. J. Catal. 2013, 307, 327-339, DOI 10.1016/j.jcat.2013.07.013. (34) Zhu, J.; Li, H.; Zhong, L.; Xiao, P.; Xu, X.; Yang, X.; Zhao, Z.; Li, J. Perovskite oxides: preparation, characterizations, and applications in heterogeneous catalysis. ACS Catal. 2014, 4 (9), 2917-2940, DOI 10.1021/cs500606g. (35) Onrubia, J. A.; Pereda-Ayo, B.; De-La-Torre, U.; González-Velasco, J. R. Key factors in Sr-doped LaBO3 (B = Co or Mn) perovskites for NO oxidation in efficient diesel exhaust purification. Appl. Catal., B 2017, 213, 198-210, DOI 10.1016/j.apcatb.2017.04.068. (36) Pereñíguez, R.; Hueso, J. L.; Gaillard, F.; Holgado, J. P.; Caballero, A. Study of oxygen reactivity in La1−xSrxCoO3−δ perovskites for total oxidation of toluene. Catal. Lett. 2012, 142 (4), 408-416, DOI 10.1007/s10562-012-0799-z. (37) Yoon, D. Y.; Lim, E.; Kim, Y. J.; Kim, J. H.; Ryu, T.; Lee, S.; Cho, B. K.; Nam, I.-S.; Choung, J. W.; Yoo, S. NO oxidation activity of Ag-doped perovskite catalysts. J. Catal. 2014, 319, 182-193, DOI 10.1016/j.jcat.2014.09.007. (38) Merino, N. A.; Barbero, B. P.; Eloy, P.; Cadús, L. E. La 1−xCaxCoO3 perovskite-type oxides: Identification of the surface oxygen species by XPS. Appl. Surf. Sci. 2006, 253 (3), 1489-1493, DOI 10.1016/j.apsusc.2006.02.035. (39) Zhang, R.; Luo, N.; Chen, B.; Kaliaguine, S. Soot combustion over lanthanum cobaltites and related oxides for diesel exhaust treatment. Energy Fuels 2010, 24 (7), 3719-3726, DOI 10.1021/ef901279w. (40) Zhu, J.; Zhao, Z.; Xiao, D.; Li, J.; Yang, X.; Wu, Y. Study of La 2−xSrxCuO4 (x=0.0, 0.5, 1.0) catalysts for NO+CO reaction from the measurements of O2-TPD, H2-TPR and cyclic voltammetry. J. Mol. Catal. A: Chem. 2005, 238 (1-2), 35-40, DOI 10.1016/j.molcata.2005.03.036.

14

ACS Paragon Plus Environment

Page 14 of 15

Page 15 of 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

Synopsis Abundant oxygen vacancies were created into LaCoO3 perovskites by the combination of Sr doping and Ar plasma treatment. TOC

15

ACS Paragon Plus Environment