Polyimide stripping device for producing detection windows on fused

Polyimide stripping device for producing detection windows on fused-silica tubing used in capillary electrophoresis. Randy M. McCormick, and Robert J...
0 downloads 0 Views 959KB Size
750

Anal. Chem. 1991, 63, 750-752

(3) Harris-Warrick, R. M.; Elkana, Y.; Ehrlich, S. D.; Lederberg, J. R o c . Nat. Aced. Sci. U . S . A . 1975, 7 2 , 2207-2211. (4) Polsky. F.; Edgell. M. H.; Siedman, J. G.; Leder, P. Anal. Bimhem. 1978. 87. 397-410. (5) Aaij, C.; Borst, P. Blochim. Biophys. Acta 1972, 269, 192-200. (6) Sharp. P. A.; Sugden, B.; Sambrook, J. Biochemistry 1973, 12, 3055-3063. (7) Brunk, C. F.; Simpson, L. Anal. Biochem. 1977, 82, 455-462. (8) O'Farrell, P. H. J . Bid. Chem. 1975, 250, 4007-4021. (9) Hassur, S.M.; Whitlock, H. W. Anal. Blochem. 1974, 5 9 , 162-164. (10) Clarke, P.: Lin, H.; Wilcox, G. Anal. Biochem. 1982, 124, 88-91. (11) Sweedler. J. V.; Bilhorn. R. B.; Epperson, P. M.; Sims. G. R.; Denton, M. B. Anal. Chem. 1988. 6 0 , 282A-291A. (12) Epperson. P. M.; Sweedler, J. V.; Bilhorn, R. B.; Sims, G. R.; Denton, M. 6. Anal. Chem. 1988, 6 0 , 327A-335A. (13) Sutherland, J. C.: Lin. B.; Monteleone. D. C.; Mugavero, J.; Sutherland, B. M.; Trunk, J. Anal. Biochem. 1987, 163, 446-457. (14) Jackson, P.; Urwin. V. E.: Mackey, C. D. Nectrophoresis 1988. 9 17). 330-339 (15) Murray, K.: Murray, N. E. J . Mol. Biol. 1975, 9 8 , 551-564. (16) Savitzky. A . ; Golay, J. E. Anal. Chem. 1984, 36, 1627-1639

(17) Schwartz, D. C.; Cantor, C. R . Cell 1884, 37. 67-75. (18) AngermuHer, S. A,; Skyavedra-Soto, L. A. Bbtechnigues 1990, 8 , 36-37. (19) Fritsch, E. F.; Manlatk, T. A&!ec&r Ching: A Laboratmy rklenuel, 2nd ed.; Cold Spring Harbor Laboratory Press: New Ywk. 1989: p 6.15.

RECEIVED for review October 23, 1990. Accepted January 7, 1991. The Ames Laboratory is operated by Iowa State University for the U.S. Department of Energy under Contract No. W-7405-Eng-82. This work was supported by the Director of Energy Research, Office of Health and Environmental Research, and by the Office of Basic Energy Sciences, Division of Chemical Sciences. Prints of the video images were produced a t the Image Analysis Facility, which is supported by the Iowa State University Biotechnology Council.

Polyimide Stripping Device for Producing Detection Windows on Fused-Silica Tubing Used in Capillary Electrophoresis Randy M. McCormick* a n d Robert J. Zagursky'

Central Research and Development Department, Experimental Station, E. I . du Pont de Nemours & Co., Inc., P.O. Box 80228, Wilmington, Delaware 19880-0228 INTRODUCTION Separations in capillary electrophoresis (CE) are usually performed in a length of small inner diameter fused-silica capillary which is clad with a layer of polyimide to protect the fragile silica tubing underneath from breakage. Although the polyimide coating imparts substantial flexibility and durability to the capillary, it also masks the superior optical properties of the underlying silica. Thus, a small region (5-10 mm) on the exterior of the capillary must be stripped of the polyimide before that section can be used as the detection cell when installed in the optical path of an absorbance (1) or a fluorescence (2)detector. Removal of the polyimide to expose the underlying silica tubing is commonly accomplished by using a small flame (3) or a heating element ( 4 , 5), and a device is commercially available (Polyimide Stripper, Polymicro Technologies, Phoenix, AZ) which employs a resistive heating coil energized with a rechargeable battery power supply to burn away the polyimide. Although these methods produce optically clear windows by removing the polyimide coating, they both have limitations. Use of a flame requires caution, as it can sometimes soften and consequently distort the silica capillary. The commercially available polyimide stripper, which has a maximum operating temperature below the softening point of silica, obviates this problem, though the device is rather expensive. However, since these approaches remove the polyimide by thermally decomposing the polymer, the capillary is subjected to considerable heat. Neither method can be used to remove polyimide from chemically derivatized (6) or gelfilled (7) capillaries, as the intense heat would pyrolyze the bonded phase or disrupt the integrity of the polyacrylamide or agarose matrices, respectively, in such capillaries. For preparation of derivatized or gel-filled capillaries, the window must be formed before the capillary is chemically derivatized or is filled with gel medium. However, removal of the polyimide weakens the mechanical strength of the T h e Du P o n t M e r c k Pharmaceutical Co., Research and Development, Wilmington, DE 19880-0328.

capillary in the denuded region, and hence the fragile capillaries must be handled gingerly during the derivatization or gel-filling procedure to prevent breakage. Removal of small sections (e.g.,