Porous N-Doped Carbon Prepared from Triazine-Based Polypyrrole

Oct 7, 2016 - ... from Triazine-Based Polypyrrole Network: A Highly Efficient Metal-Free Catalyst ... For a more comprehensive list of citations to th...
0 downloads 0 Views 7MB Size
Subscriber access provided by CORNELL UNIVERSITY LIBRARY

Article

Porous N-Doped Carbon Prepared From Triazine-Based Polypyrrole Network: An Highly Efficient Metal-Free Catalyst for Oxygen Reduction Reaction in Alkaline Electrolytes Mei Yang, Yijiang Liu, Hongbiao Chen, Duanguang Yang, and Huaming Li ACS Appl. Mater. Interfaces, Just Accepted Manuscript • DOI: 10.1021/acsami.6b09811 • Publication Date (Web): 07 Oct 2016 Downloaded from http://pubs.acs.org on October 8, 2016

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

ACS Applied Materials & Interfaces is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 31

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

Porous N-Doped Carbon Prepared From Triazine-Based Polypyrrole Network: An Highly Efficient Metal-Free Catalyst for Oxygen Reduction Reaction in Alkaline Electrolytes

Mei Yang †, Yijiang Liu †, Hongbiao Chen *†, Duanguang Yang †, Huaming Li *†



College of Chemistry, Xiangtan University, Xiangtan 411105, Hunan Province, P. R. China.

1 ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ABSTRACT

Metal-free N-doped carbon (NC) materials have been regarded as one of the most promising catalysts for the oxygen reduction reaction (ORR) in alkaline media because of their outstanding ORR catalytic activity, high stability, and good methanol tolerance. Up to now, only a small minority of such catalysts have been synthesized from triazine-based polymeric networks. Herein, we report the synthesis of such NC catalyst by directly pyrolyzing a nitrogen-rich, triazine-based polypyrrole network (TPN). The TPN is fabricated by oxidative polymerization of 2,4,6-tripyrrol-1,3,5-triazine monomer using TfOH as the protonating agent and benzoyl peroxide as the oxidizing agent. The obtained NC-900 (pyrolyzed at 900 °C) catalyst exhibits excellent ORR activity in alkaline media with a high ORR onset potential (0.972 V vs. RHE), a large kinetic-limiting current density (15.66 mA cm−2 at 0.60 V), and good MeOH tolerance and durability. The as-synthesized NC-900 material is a potential candidate as a high active, stable, and low-cost ORR catalyst for alkaline fuel cells.

Keywords: Polymeric networks; Porous Carbon; Dope; Metal-free catalysts; ORR; Fuel cells

2 ACS Paragon Plus Environment

Page 2 of 31

Page 3 of 31

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces



INTRODUCTION

The exploitation of novel energy-storage technologies is of pivotal importance to alleviate the pressures brought about by the energy crisis.1 Fuel cells (FCs) are just in response to this need, came into being. Although FCs are currently perceived as one of the most attractive energy conversion devices,2-4 they require a cathode catalyst for the oxygen reduction reaction (ORR). Currently, platinum (Pt) and its alloys are recognized as the best catalysts towards ORR. Unfortunately, these precious-metal based catalysts usually suffer from high cost, prone to MeOH/CO poisoning, sluggish ORR kinetics, and inadequate durability, which obstruct the extensive utilization of FCs.5-8 Aiming at these problems, the global research priorities have been committed to seeking other non-Pt catalysts that can promote the ORR. Among alternative catalysts, nitrogen-doped carbon (NC) materials appear to be the most promising metal-free catalysts for ORR in terms of high catalytic activity, low cost, and good durability.9-12 Current methods for the preparation of NC catalysts can ordinarily be divided into three categories, that is, direct-growth, post-synthesis, and direct-pyrolysis. The direct-growth method involves in-situ N doping on carbon framework during the carbon growth process, which is commonly used for synthesizing N-doped carbon nanotubes (CNTs) and carbon nanofibers (CNFs).13-17 The post-synthesis approach attempts to heat-treat carbons (CNTs, graphenes, carbon blacks) with N-enriched precursors.18-22 A variety of N-rich small molecules such as ammonia,23 ammonium fluoride,24,25 melamine,25 cyanamide,26 urea,27 ethylenediamine,28 etc. have been adopted. The last approach involves direct pyrolysis of N-rich polymers such as polyacrylonitrile (PAN),29,30

3 ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

polyaniline (PANI),29,31 polypyrrole (PPy),29 and melamine-formaldehyde (MF) resin.32 In most cases, however, the as-claimed metal-free NC catalysts contain metal impurities, for example, iron residues in CNTs prepared by chemical vapor deposition;33,34 manganese residues in graphene oxide prepared by Hummer’s method;35 FeCl3 in PPy and PANI prepared by oxidative polymerization.36,37 Although the metal residues were later removed by mineral acids leaching, the complete removal of metal residues is impossible. For instance, Jurkschat et al. have confirmed that even if the washing time of CNTs in 2 M HNO3 was extended to 36 h (namely “super washing”), iron impurities could not completely removed.38 The residual metals, especially Fe, even at trace levels that are undetectable by X-ray photoelectron spectroscopy (XPS) and energy dispersive X-ray spectroscopy (EDX), can significantly promote ORR activity.39,40 Meanwhile, the preparation of the so-called M-N/C (M = Fe, Co, Ni, or Mn) catalysts also produces “NC-type” active sites that are analogous to the metal-free NC catalysts. That is to say, there are two kinds of active sites in the M-N/C catalysts: M−Nx active sites and “NC-type” sites. However, it is difficult to evaluate their respective contributions towards ORR exactly. In this sense, it is of great importance to prepare truly metal-free NC catalysts without applying any metal-containing raw materials throughout the entire synthesis procedure. Recently, the development of porous organic networks (PONs) offers an excellent chance for the controllable construction of the NC catalysts. The advantages of PONs include large specific surface areas and abundant pore distributions, which are favorable to increase the catalytic active sites. Moreover, the N atoms can be controllably introduced into the networks by using designed N-containing building blocks. The fixation of the N atoms within the rigid polymeric networks

4 ACS Paragon Plus Environment

Page 4 of 31

Page 5 of 31

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

together with the high skeletal strength further offers an attractive route towards creating the self-supported NC materials uniformly doped with N element. Up to now, however, only minorities of the N-enriched PONs were used to prepare such NC catalysts.41-44 Therefore, it is really a challenge to prepare novel N-enriched PONs for the production of the NC catalysts. Based on the above analysis, we herein developed a facile approach to fabricate metal-free NC catalyst by directly pyrolyzing an N-rich, triazine-based polypyrrole network (TPN). We chose N-rich 2,4,6-tripyrrol-1,3,5-triazine (TPT) monomer to prepare TPN. The TPT was oxidative polymerized in the presence of TfOH using benzoyl peroxide (BPO) as the oxidizing agent, in which TfOH was used to protonate TPT. Conversely, the common strong organic oxyacids such as p-toluenesulfonic acid cannot induce the polymerization. The advantages of using BPO and TfOH are that the polymerization can be completed within 1 h, and that can completely dispense with the use of any metal precursors. In this manner, truly metal-free NC catalyst can be fabricated by directly pyrolyzing the obtained TPN. Our synthesis strategy offers a chance to investigate the nature of catalytic sites for ORR in a “clean” trinary system, with only carbon, oxygen and nitrogen elements. Compared with the commercial Pt/C catalyst, the as-synthesized NC-900 (pyrolyzed at 900 °C) catalyst displays a slightly higher ORR activity in alkaline media with the onset potential of 0.972 V (vs. RHE), half-wave potential of 0.855 V (vs. RHE), and limiting current density of 5.05 mA cm−2. Considering that TPT is easily synthesized in multigram quantities at a price less than U.S. $1.2 per gram (Table S1, see Supporting Information), the as-prepared NC-900 catalyst (U.S. $7.5 per gram) is much cheaper than the commercial 20 wt% Pt/C catalyst (Johnson Matthey, U.S. $97.3 per gram). Such low-cost and remarkable

5 ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

electrochemical performance makes this NC material as a promising candidate for feasible ORR catalyst.



EXPERIMENT SECTION

Synthesis of TPN and metal-free NC catalysts

TPT was prepared according to the procedure reported previously by our group.22 For the synthesis of TPN, TPT (2.76 g, 10.0 mmol) and TfOH (9.00 g, 60.0 mmol) were dissolved in dichloroethane (100 mL). The reaction mixture was heated to 80 °C followed by the addition of BPO (8.72 g, 36.0 mmol). The polymerization was conducted under stirring for 1 h at this temperature. After cooling to room temperature, the polymer (TPN salt) was filtered, washed with water (3 × 200 mL) and acetone (3 × 100 mL). The TPN was further purified by dispersing the TPN salt (4.0 g) in NaOH aqueous solution (1.0 M, 200 mL). After stirring at ambient temperature for 12 h, the base TPN was filtered, washed with water until pH = 7, and finally dried under vacuum. The NC catalysts were synthesized by directly pyrolyzing the TPN (200 mg) at 800–1000 °C for 2 h under flowing argon atmosphere. The heating rate was fixed at 4 °C min–1 and the products were labeled as NC-800, NC-900, and NC-1000, respectively. To highlight the importance of oxidative polymerization, the TPT monomer was directly pyrolyzed at 900 °C (the optimal pyrolysis temperature for the TPN) for 2 h and the product was labeled as TPT-900. The electrochemical results confirmed that the ORR activity of the TPT-900 sample was much lower than that of the NC-900 catalyst (Fig. S1, see Supporting Information). Moreover, the yield of carbon in the

6 ACS Paragon Plus Environment

Page 6 of 31

Page 7 of 31

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

monomer pyrolysis (0.7 wt%) was significantly lower than that in the TPN pyrolysis (25.8 wt%) because the monomer is easy to sublimate. The elemental composition and electrochemical performance of the NC-900 catalyst are listed in Table 1.

Electrochemical measurements

A CHI760D electrochemical workstation (Shanghai Chenhua Co., China) with a three-electrode system was used to carry out the electrochemical tests. Graphite electrode was used as the counter electrode and Ag/AgCl (KCl-saturated) electrode was used as the reference electrode. All measured potentials were converted to the reversible hydrogen electrode (RHE) scale via the Nernst equation45 (see Supporting Information). The glassy carbon electrode (area = 0.196 cm2) was used as the working electrode. For the NC-900 catalyst, the mass of catalyst loaded onto the glassy carbon electrode is 357 µg cm–2. For the commercial 20 wt% Pt/C catalyst (Johnson Matthey, hereafter denoted as “Pt/C”), the mass of Pt/C catalyst loaded onto the electrode is 100 µg cm–2, corresponding to the metal Pt loading of 20 µgPt cm–2. Cyclic voltammetry (CV) and linear sweep voltammetry (LSV) techniques on rotating disk electrode (RDE, Pine Research Instrumentation) as well as LSV technique on rotating ring disk electrode (RRDE, Pine Research Instrumentation) were carried out in O2 (or N2)-saturated 0.1 M KOH aqueous solution at 25 oC.



RESULTS AND DISCUSSION

Preparation and characterization of metal-free NC catalysts

7 ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

In our previous article,46 we reported the preparation of self-supported, Fe/N-co-doped carbon (Fe-N/C) as the efficient ORR catalyst through pyrolysis of TPT-based PON and Fe(II) acetate mixture. The PON was fabricated by the FeCl3-catalyzed Friedel-Crafts polymerization of TPT with dimethoxymethane as the cross-linking agent. The obtained Fe-N/C catalyst showed a promising catalytic activity towards ORR in alkaline electrolytes, in which the Fe-Nx species was found to serve as the predominant active centers for ORR. In an attempt to evaluate the contribution of iron residues to the ORR performance, we try to remove the Fe residues completely. The as-synthesized Fe-N/C electrocatalyst was thus washed in aqueous solution of H2SO4 (0.5 M) at 80 °C for up to one week. It was found that the Fe content was firstly declined but then leveled off, indicating that sulphuric acid leaching cannot completely remove all the Fe residues from carbons, peculiarly Fe embedded in graphitic layers. Considering that the preparation of the M-N/C catalysts also produces nitrogenized groups as in the case of NC catalysts, it is difficult to assess their respective contributions toward ORR because some nitrogenized groups are also ORR active. From this point of view, it is extremely desirable to prepare truly metal-free NC catalysts dispensing with the need for any metallic precursors as mentioned above. In this paper, the TPN was fabricated by oxidative polymerization of TPT monomer using TfOH as the protonating agent and BPO as the oxidizing agent (Scheme S1, see Supporting Information), which would dispense with the use of any metal precursors. The most probable polymerization mechanism involves protonation of TPT by TfOH, followed by oxidation of protonated pyrrole rings in the TPT with benzoyloxy radicals, leading to the formation of pyrrole radical cations.

8 ACS Paragon Plus Environment

Page 8 of 31

Page 9 of 31

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

Such radical cations undergo dimerization followed by deprotonation to form pyrrole dimer. The bipyrrole is then protonated and oxidized in a similar manner and combines with another oxidized species. In the next growth step, protonation, reoxidation, combination, and deprotonation go on to produce TPN eventually (Scheme S2, see Supporting Information).47-49 The metal-free NC catalysts were then synthesized by the pyrolysis of the TPN from 800 to 1000 °C under flowing Ar, the products are labeled as NC-800, NC-900, and NC-1000, respectively. The electrochemical results showed that the NC-900 catalyst displayed the maximum catalytic activity towards ORR (Figs. S2, S3, see Supporting Information), we therefore focus on the NC-900 catalyst in the following research.

Fig. 1. SEM images of the TPN precursor (a) and the NC-900 catalyst (b) (the inset depicts a single spherical particle). TEM (c) and HR-TEM (d) pictures of the NC-900 catalyst.

9 ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Fig. 1a shows the SEM images of the TPN precursor. As can be seen, the TPN polymer exhibits an irregularly spherical architecture with diameter ranging from 130 to 750 nm. In addition, aggregated particles can be clearly seen. After pyrolysis, the spherical morphology is still maintained, but the surface become rough and porous (inset of Fig. 1b). Fig. 1c depicts the TEM images of the as-prepared NC-900 catalyst. In agreement with the SEM observation, agglomerated spherical particles are observed again. The high-magnification TEM image in Fig. 1d reveals that the NC-900 catalyst is basically amorphous carbon.

Fig. 2. Nitrogen sorption isotherms at 77 K (a) and DFT pore size distribution curve (b) of the NC-900 catalyst. Raman (c) and high-resolution N 1s XPS (d) spectra of the NC-900 catalyst.

10 ACS Paragon Plus Environment

Page 10 of 31

Page 11 of 31

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

The porosity of the NC-900 catalyst was investigated by N2 sorption analysis. The BET surface area of TPN precursor is 100 m2 g−1 (Fig. S4a, see Supporting Information). After pyrolysis, the BET surface area of the NC-900 catalyst increases greatly and reaches up to 779 m2 g−1 (Fig. 2a). According to the IUPAC classification, the NC-900 sample exhibits a type-IV isotherm with a type-H4 hysteresis loop at p/po = 0.45. The appearance of type-H4 hysteresis loop is indicative of the presence of mesopores.50,51 Fig. 2b depicts the pore size distribution (PSD) for the NC-900 catalyst calculated by density functional theory (DFT) method. It is found that the porosity of the NC-900 catalyst is consisted of a large proportion of mesopores and a very small proportion of macropores. The Raman spectrum of the NC-900 catalyst shown in Fig. 2c exhibits the ordered graphitic carbon band at 1589 cm−1 (G band) and defect band at 1336 cm−1 (D band).52,53 The ratio of intensity of D/G bands (ID/IG) can give an quantitative estimation of the degree of graphitization. The NC-900 catalyst possesses an ID/IG value of 0.98, indicating that the extent of graphitization is very low. The wide-scan XPS spectrum of the NC-900 catalyst (Fig. S5, see Supporting Information) demonstrates the existence of three kinds of elements: carbon (90.5%), nitrogen (3.02%), and oxygen (6.48%). Notably, the abnormal high O content is unlikely from adsorption as exposed to air. But it could be understood considering the radical coupling reaction between benzoyloxy radicals and the propagating PPy radical cations. At the final stage of the polymerization, the propagating PPy radical cations become insoluble or on the verge of insolubility in solvent. Combination of propagating PPy radical cations via their radical ends becomes progressively more difficult. In contrast, the cross-coupling reaction between benzoyloxy

11 ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

radicals and the growing PPy radical cations becomes predominant owing to the high concentration and easy movement of the benzoyloxy radicals. Such reaction can generate ester group in the TPN polymer, which is evident by the appearance of ester C=O absorption band at 1728 cm−1 in the FTIR spectrum of TPN (Fig. S6, see Supporting Information). Supporting evidence comes from elemental analysis of the TPN polymer, which shows an atomic composition of 57.33% C, 4.53% H, 19.24% N, and 18.9% O (Table S3, see Supporting Information). The deconvoluted C 1s spectrum (Fig. S7, see Supporting Information) shows four peaks at 284.7 ± 0.2 eV (C=C-C), 285.6 ± 0.2 eV (C-N/C-O), 288.1 ± 0.2 eV (C=O), and 291.1 ± 0.2 eV (π-π*). Similarly, the deconvoluted O 1s spectrum (Fig. S8, see Supporting Information) also shows four peaks at 531.1 ± 0.1 eV (C=O), 532.4 ± 0.1 eV (C-O), 533.5 ± 0.1 eV (C-OH), and 536.1 ± 0.1 eV (adsorbed H2O or O2).31 The deconvoluted N 1s XPS spectrum in Fig. 2d again displays four peaks at 398.6 ± 0.1 eV (pyridinic-N), 400.3 ± 0.1 eV (pyrrolic-N), 401.2 ± 0.1 eV (graphitic-N), 403.7 ± 0.1 eV (pyridinic-N+-O-),54,55 and these four kinds of N atoms are found to be 26.18%, 16.45%, 38.85%, and 18.52%, respectively. The high graphitic-N content (38.85%) endows the catalyst with enhanced electrical conductivity. To prove this, the electrical conductivity of the NC-900 catalyst was studied using a four probe measurement and was found to be 3.4 S cm−1. Furthermore, the NC-900 sample also showed small internal resistance (0.36 Ω) and charge transfer resistance (0.66 Ω) as determined by EIS measurement (Fig. S9, see Supporting Information). Such low resistance as well as N and O co-doping will play a very important role for its high ORR activity.

ORR activity

12 ACS Paragon Plus Environment

Page 12 of 31

Page 13 of 31

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

Cyclic voltammograms (CV) of the NC-900 catalyst in N2- or O2-saturated alkaline media (0.1 M KOH solution) were initially investigated to evaluate the ORR activity. In N2-saturated alkaline solution, no redox peaks can be observed for the NC-900 catalyst (Fig. 3a). In contrast, a distinct ORR peak was observed for the NC-900 catalyst when O2 was introduced. The peak potential of the NC-900 catalyst is 0.809 ± 0.005 V (vs. RHE), which is slight positive compared to the Pt/C catalyst (0.805 ± 0.005 V vs. RHE). In addition, the NC-900 catalyst has a higher ORR peak current density (3.00 ± 0.02 mA cm−2) than the Pt/C catalyst (2.40 ± 0.02 mA cm−2). Linear sweep voltammograms (LSVs) for the NC-900 catalyst in O2-saturated alkaline solution were then performed to further evaluate its ORR performance. All LSV curves present in the figure have been corrected by removing the background signals obtained in N2 saturated alkaline electrolyte. The ORR onset (Eo) and half-wave (E1/2) potentials for the NC-900 catalyst shown in Fig. 3c were found to be 0.972 and 0.855 V (vs. RHE), respectively, which were comparable to the Pt/C catalyst (Eo = 0.965 V, E1/2 = 0.845 V vs. RHE). Additionally, the limiting current density (JL) of the NC-900 catalyst is about 5.05 mA cm−2 in KOH solution, which is comparable to the Pt/C catalyst (5.26 mA cm−2). Considering that the loading for the Pt/C catalyst is less than that for the NC-900 catalyst, their ORR current densities are also compared in terms of mass activity (Table S7, see Supporting Information). The Tafel slope of the NC-900 catalyst in the potential range of 0.95–0.85 V (vs. RHE) is ca. 97 mV decade–1, which is also comparable to the Pt/C catalyst (ca. 95 mV decade–1, Fig. S10, see Supporting Information). This demonstrates that the ORR kinetics on the NC-900 catalyst resembles that on the Pt/C catalyst. With respect to the Eo, E1/2, and JL values, the ORR activity of the NC-900 catalyst is considerably higher than most recently reported NC

13 ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

catalysts, but is still inferior to some M-N/C catalysts reported to date (Table S9, see Supporting Information).

Fig. 3. (a) CVs of the NC-900 and Pt/C catalysts in N2- and O2-saturated 0.1 M KOH solution with a scan rate of 50 mV s−1. (b, c) LSV curves of the NC-900 catalyst in N2- and O2-saturated 0.1 M KOH solution with various rotation speeds at a sweep rate of 10 mV s−1 (b) and LSVs of the NC-900 and Pt/C catalysts in O2-saturated 0.1 M KOH solution with the rotation speed and sweep rate of 1600 rpm and 10 mV s−1, respectively (c, the inset of c shows the K−L plots of the NC-900 and Pt/C catalyst at 0.60 V). (d) The Jk and n involved in the ORR of the NC-900 and Pt/C catalysts at 0.65, 0.60, and 0.55 V (vs. RHE).

LSVs for the NC-900 catalyst with varying catalyst loading were also performed at 1600 rpm in

14 ACS Paragon Plus Environment

Page 14 of 31

Page 15 of 31

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

O2-saturated alkaline media to investigate the influence of catalyst loading on its activity towards ORR. As depicted in Fig. S11 (see Supporting Information), the Eo, E1/2, and JL values measured with the NC-900 at a loading of 257 µg cm−2 decreased obviously compared to that of 357 µg cm−2 loading. When the loading of NC-900 catalyst increased to 457 µg cm−2, the Eo value remained almost unchanged although the JL value increased slightly, indicating that the ORR catalytic activity relied on the mass loading of catalyst but had an optimal catalyst loading. To understand the catalytic mechanism of ORR on the NC-900 catalyst, LSV measurements on a RDE were further carried out in O2-saturated alkaline solution with different rotation rates. The Koutecky-Levich (K-L)56 profiles (J−1 versus ω−1/2) of the NC-900 and Pt/C catalysts were compared at 0.6 V (vs. RHE) and other potentials (inset of Fig. 3c, Figure S13, see Supporting Information). All K-L plots are linear regardless of the potentials. Furthermore, the value of kinetic current density (JK) can be estimated from the intercepts of the linear K-L plots in O2-saturated alkaline electrolyte. As shown in Fig. 3d, the corresponding JK value of the NC-900 catalyst is 15.66 mA cm−2 at 0.60 V (vs. RHE), close to that of the Pt/C catalyst (17.54 mA cm−2). This may be due to the high specific surface area and abundant mesoporous structure of the NC-900 catalyst, which lead to a rapid electron transfer. The average electron transfer numbers (n) of the NC-900 catalyst are calculated to be ca. 3.98 in alkaline solution, indicating that the ORR process on the NC-900 catalyst is dominated by a 4e reduction pathway. Further evidence of the 4e reduction pathway comes from the RRDE tests, in which the n and the H2O2 generation rate of the NC-900 catalyst can be determined. The disk current (id) and the ring current (ir) response on the NC-900 and Pt/C catalysts at 900 rpm in 0.1 M KOH solution are

15 ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

depicted in Fig. 4a, b. The corresponding H2O2 yield (%) and n are shown in Fig. 4c, d. For the NC-900 catalyst, obviously, the H2O2 yield is less than 10% and the average n value is 3.92, which are very close to the Pt/C catalyst. The average n value of the NC-900 catalyst determined by RRDE tests (3.92) is almost equal to that estimated by K−L plots (3.98), again demonstrating good selectivity towards the 4e pathway.

Fig. 4. RRDE voltammograms of the NC-900 (a) and Pt/C (b) catalysts at 900 rpm in O2-saturated 0.1 M KOH with a scan rate of 10 mV s−1. Peroxide yield (black) and n (red) of the NC-900 (c) and Pt/C (d) catalysts derived from RRDE measurement.

Based on the above research results, the excellent ORR activity of the NC-900 catalyst is possibly due to the following reasons. Firstly, the relative amount of N-based functional groups detected on

16 ACS Paragon Plus Environment

Page 16 of 31

Page 17 of 31

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

the NC-900 catalyst by XPS is pyridinic-N (26.18%), pyrrolic-N (16.45%), graphitic-N (38.85%), and pyridinic-N+-O− (18.52%) (Table S5, see Supporting Information) as mentioned before, in which both pyridinic-N and graphitic-N have been suggested as the ORR active sites.57,58 Clearly, the total content of ORR active N (pyridinic-N + graphitic-N) can reach up to 65.03% in the NC-900 catalyst. The high proportion of graphitic-N can also favor 4e process in ORR as confirmed by previous studies.30,59 Secondly, the relatively high O content (6.48%) of the NC-900 catalyst is at least part of the reason causing its high ORR activity because O-containing groups, especially the quinone groups, can facilitate O2 adsorption and its subsequent reduction.60,61 As a result, the catalytic effects of the O-functionalities (such as carboxyl, carbonyl, and hydroxyl groups) on the CNFs surface towards ORR were recently confirmed by Niu and Zhang et al.,62 in which they found that the carboxylic acid groups have the highest catalytic activity, followed by the carbonyl groups and the hydroxyl groups. Interestingly, further N-functionalization of the O-modified CNFs can change the ORR pathway from a two-plateau 2e to a one-plateau 4e reduction due to the coexistence of O- and N-containing groups in CNFs.62 In our case, the synergistic influence of N- and O-containing functionalities was also investigated by analyzing the deconvoluted C 1s spectrum of the NC-900 catalyst (Fig. S7, Table S4, see Supporting Information). The relative contents of C atoms that directly bonded to O atoms (C=O) and O/N atoms (C-O/C-N) are 11.45 % and 23.00 %, respectively, in which both C=O and C-O groups should be ORR active as mentioned above. Furthermore, the high level of C-O/C-N groups indicates that the NC-900 catalyst contains plenty of C−OH groups, many of them are neighbored by the N-containing species because the N content is only ca. 3%. That is to say, pyridone groups

17 ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

must exist in the NC-900 catalyst and should be included in the peak of pyrrolic-N in the high-resolution N 1s XPS spectrum (Fig. 2d).63 Note that pyridone is also proposed as the ORR active site owing to the fact that it can undergo tautomerization with hydroxypyridine, which can stabilize singlet dioxygen through the formation of oxygen adduct, as demonstrated by Asefa and coworkers.30,64 Finally, the relatively high surface area (779 m2 g−1) and predominant mesostructure of the NC-900 catalyst have an almost direct impact on the ORR activity because they provide abundant ORR active sites and be beneficial to the mass transfer of O2. All in all, the excellent ORR activity of the NC-900 catalyst is virtually a collective property of all beneficial effects mentioned above and can hardly be separated.

Fig. 5. ORR polarization plots measured with the NC-900 (a) and Pt/C (b) catalysts during cycling durability tests in O2-saturated 0.1 M KOH solution, inset of a shows MeOH-poison effect evaluation on the current–time (i–t) chronoamperometric response, inset of b shows durability evaluation on the current–time (i–t) chronoamperometric response for 10,000 s. For all tests, the rotation rate is 1600 rpm and the scan rate is 10 mV s−1.

18 ACS Paragon Plus Environment

Page 18 of 31

Page 19 of 31

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

To investigate the MeOH crossover effect and durability of the NC-900 catalyst, we carried out chronoamperometric measurements in O2-saturated alkaline solution. It is found that the corresponding amperometric response for the NC-900 catalyst has stayed the same after adding MeOH (3 M) at 145 s (inset of Fig. 5a), showing a remarkably good tolerance to crossover effects. In contrast, the Pt/C catalyst suffers a sharp decrease, demonstrating that the Pt/C catalyst is prone to MeOH poisoning. The durability evaluation on the i–t chronoamperometric response was further performed on the NC-900 and Pt/C catalysts for 10,000 s (inset of Fig. 5b). It was found that the NC-900 catalyst exhibited better long-term stability than the Pt/C catalyst. The electrochemical stabilities of the NC-900 and Pt/C catalysts were then evaluated by endurance tests for 3 000 cycles in O2-saturated alkaline solution with the rotation speed and scan rate of 1600 rpm and 50 mV s−1, respectively. After 3 000 cycles, the E1/2 shifted negatively by 5.0 mV (vs. RHE) for the NC-900 catalyst (Fig. 5a). For the Pt/C catalyst (Fig. 5b), however, the corresponding value was changed to 10 mV (vs. RHE), implying that the NC-900 catalyst has a very fine application prospects in FCs.

Table 1. The ORR performance of the NC-900 and Pt/C catalysts in O2-saturated 0.1 M KOH solution.

Samples

a,b

Eo

E1/2

Jk a

JL −2

−2

nb

(V)

(V)

(mA cm )

(mA cm )

Pt/C

0.965

0.845

5.26

17.54

3.99

NC-900

0.972

0.855

5.05

15.66

3.98

Estimated by the K-L plots at 0.60 V (vs. RHE).

19 ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60



CONCLUSION

In summary, we have successfully developed a facile and economic method for synthesis of metal-free NC catalyst towards ORR by simply pyrolyzing polymeric network (TPN) in Ar. The TPN was fabricated by oxidation polymerization of TPT monomer using TfOH as the protonating agent and BPO as the oxidizing agent. Our synthesis strategy offers a chance to investigate the nature of catalytic sites for ORR in a “clean” trinary system, with only carbon, oxygen and nitrogen elements. The as-prepared NC-900 catalyst possessed a mesoporous structure and a relatively high nitrogen (3.02 at.%) and oxygen (6.48 at.%) contents. This novel metal-free catalyst exhibited excellent ORR activity as well as high selectivity towards a 4e reduction pathway in alkaline media, which places it among the best metal-free NC catalysts for ORR reported to date.



ASSOCIATED CONTENT

Supporting Information

This material is available free of charge on the ACS Publications website at DOI: 10.1021/acsami.xxxxxxx. Schematic illustration for the preparation of TPN; possible mechanism for the TPT polymerization; N2 sorption isotherms and PSD for TPN; FT-IR spectrum 20 ACS Paragon Plus Environment

Page 20 of 31

Page 21 of 31

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

of TPN; wide-scan XPS, and deconvoluted C 1s and O 1s spectra for NC-900 catalyst; LSV, CV, and Nyquist plots for NC-800, NC-900, and NC-1000 catalysts; LSVs of NC-900 catalyst with different mass loadings; Tafel plots for NC-900 and Pt/C catalysts; LSVs of Pt/C at different rotation speeds; K-L profiles of NC-900 and Pt/C catalysts at different potentials; cost estimation for NC-900 catalyst; ORR performances of various ORR catalysts (PDF)



AUTHOR INFORMATION

Corresponding Authors *E-mail: [email protected]; Tel: +86 731 58298572; Fax: +86 731 58293264. *E-mail: [email protected] Notes The authors declare no competing financial interest.



ACKNOWLEDGMENTS

Financial support from Program for NSFC (51272219, 51674219), RFDP (20124301110006), and the Construct Program of the Key Discipline in Hunan Province is greatly acknowledged.



REFERENCES

[1] Wang Y.; Chen K. S.; Mishler J.; Cho S. C.; Adroher X. C. A Review of Polymer Electrolyte Membrane Fuel Cells: Technology, Applications, and Needs on Fundamental Research. Appl. Energy 2011, 88, 981–1007.

21 ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

[2] Liu S. H.; Chen S. C.; Sie W. H. Heat-Treated Platinum Nanoparticles Embedded in Nitrogen-Doped Ordered Mesoporous Carbons: Synthesis, Characterization and Their Electrocatalytic Properties toward Methanol-Tolerant Oxygen Reduction. Int. J. Hydrogen Energy 2011, 36, 15060–15067. [3] Winter M.; Brodd R. J. What are Batteries, Fuel Cells, and Supercapacitors?. Chem. Rev. 2004, 104, 4245–4270. [4] Yang D. S.; Bhattacharjya D.; Inamdar S.; Park J.; Yu J. S. Phosphorus-Doped Ordered Mesoporous Carbons with Different Lengths as Efficient Metal-Free Electrocatalysts for Oxygen Reduction Reaction in Alkaline Media. J. Am. Chem. Soc. 2012, 34, 16127–16130. [5] Chen Z.; Waje M.; Li W.; Yan Y. Supportless Pt and PtPd Nanotubes as Electrocatalysts for Oxygen-Reduction Reactions. Angew. Chem. Int. Ed. 2007, 46, 4060–4063. [6] Zhou Y.; Neyerlin K.; Olson T. S.; Pylypenko S.; Bult J.; Dinh H. N.; Gennett T.; Shao Z.; O'Hayre R. Enhancement of Pt and Pt-alloy Fuel Cell Catalyst Activity and Durability via Nitrogen-Modified Carbon Supports. Energy Environ. Sci. 2010, 3, 1437–1446. [7] Zhang S.; Shao Y.; Yin G.; Lin Y. Recent Progress in Nanostructured Electrocatalysts for PEM Fuel Cells. J. Mater. Chem. A 2013, 1, 4631–4641. [8] Wen Z.; Wang Q.; Li J. Template Synthesis of Aligned Carbon Nanotube Arrays using Glucose as a Carbon Source: Pt Decoration of Inner and Outer Nanotube Surfaces for Fuel-Cell Catalysts. Adv. Funct. Mater. 2008, 18, 959–964.

22 ACS Paragon Plus Environment

Page 22 of 31

Page 23 of 31

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

[9] Zhou X.; Yang Z.; Nie H.; Yao Z.; Zhang L.; Huang S. Catalyst-Free Growth of Large Scale Nitrogen-Doped Carbon Spheres as Efficient Electrocatalysts for Oxygen Reduction in Alkaline Medium. J. Power Sources 2011, 196, 9970–9974. [10] Liu R.; Wu D.; Feng X.; Müllen K. Nitrogen-Doped Ordered Mesoporous Graphitic Arrays with High Electrocatalytic Activity for Oxygen Reduction. Angew. Chem. Int. Ed. 2010, 49, 2565–2569. [11] Wang S.; Zhang L.; Xia Z.; Roy A.; Chang D.W.; Beak J. B.; Dai L. BCN Graphene as Efficient Metal-Free Electrocatalyst for the Oxygen Reduction Reaction. Angew. Chem. Int. Ed. 2012, 51, 4209–4212. [12] Zheng Y.; Jiao Y.; Ge L.; Jaroniec M.; Qiao S. Z. Two-Step Boron and Nitrogen Doping in Graphene for Enhanced Synergistic Catalysis. Angew. Chem. Int. Ed. 2013, 52, 3110–3116. [13] Magrez A.; Seo J. W.; Smajda R.; Mionic M.; Forro L. Catalytic CVD Synthesis of Carbon Nanotubes: towards High Yield and Low Temperature Growth. Materials 2010, 3, 4871–4891. [14] Li J.; Papadopoulos C.; Xu J. M.; Moskovits M. Highly-Ordered Carbon Nanotube Arrays for Electronics Applications. Appl. Phys. Lett. 1999, 75, 367–369. [15] Eswaramoorthi I.; Hwang L. P. Synthesis and Characterisation of Larger Diameter Multi-Walled Carbon Nanotubes over Anodic Titanium Oxide Template. Carbon 2006, 44, 2341–2344. [16] Geng D.; Chen Y.; Chen Y.; Li Y.; Li R.; Sun X.; Ye S.; Knights S. High Oxygen-Reduction Activity and Durability of Nitrogen-Doped Grapheme. Energy Environ. Sci. 2011, 4, 760–764.

23 ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

[17] Guo B.; Liu Q.; Chen E.; Zhu H.; Fang L.; Gong J. R. Controllable N-Doping of Grapheme. Nano Lett. 2010, 10, 4975–4980. [18] Park J. S.; Lee J. M.; Hwang S. K.; Lee S. H.; Lee H. -J.; Lee B. R.; Park H.; Kim J. S.; Yoo S.; Song M. H.; Kim S. O. A ZnO/N-Doped Carbon Nanotube Nanocomposite Charge Transport Layer for High Performance Optoelectronics. J. Mater. Chem. 2012, 22, 12695–12700. [19] Kundu S.; Xia W.; Busser W.; Becker M.; Schmidt D. A.; Havenith M.; Muhler M. The Formation of Nitrogen-Containing Functional Groups on Carbon Nanotube Surfaces: a Quantitative XPS and TPD Study. Phys. Chem. Chem. Phys. 2010, 12, 4351–4359. [20] Li X.; Wang H.; Robinson J. T.; Sanchez H.; Diankov G.; Dai H. Simultaneous Nitrogen Doping and Reduction of Graphene Oxide. J. Am. Chem. Soc. 2009, 131, 15939–15944. [21] Senthilnathan J.; Rao K. S.; Yoshimura M. Submerged Liquid Plasma–Low Energy Synthesis of Nitrogen-Doped Graphene for Electrochemical Applications. J. Mater. Chem. A 2014, 2, 3332–3337. [22] Yang M.; Yang D.; Chen H.; Gao Y.; Li H. Nitrogen-Doped Carbon Nanotubes as Catalysts for the Oxygen Reduction Reaction in Alkaline Medium. J. Power Sources 2015, 279, 28–35. [23] Wang X.; Lee J. S.; Zhu Q.; Liu J.; Wang Y.; Dai S. Ammonia-Treated Ordered Mesoporous Carbons as Catalytic Materials for Oxygen Reduction Reaction. Chem. Mater. 2010, 22, 2178–2180. [24] Abbas S. C.; Ding K.; Liu Q.; Huang Y.; Bu Y.; Wu J.; Lv J.; Ghausi M. A.; Wang Y. Si–C–F Decorated Porous Carbon Materials: A New Class of Electrocatalysts for the Oxygen Reduction Reaction. J. Mater. Chem. A 2016, 4, 7924–7929.

24 ACS Paragon Plus Environment

Page 24 of 31

Page 25 of 31

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

[25] Zhan Y.; Huang J.; Lin Z.; Yu X.; Zeng D.; Zhang X.; Xie F.; Zhang W.; Chen J.; Meng H. Iodine/Nitrogen Co-Doped Graphene as Metal Free Catalyst for Oxygen Reduction Reaction. Carbon 2015, 95, 930–939. [26] Jiang H.; Zhu Y.; Feng Q.; Su Y.; Yang X.; Li C. Nitrogen and Phosphorus Dual-Doped Hierarchical Porous Carbon Foams as Efficient Metal-Free Electrocatalysts for Oxygen Reduction Reactions. Chem. Eur. J. 2014, 20, 3106–3112. [27] Pan F.; Jin J.; Fu X.; Lin Q.; Zhang J. Advanced Oxygen Reduction Electrocatalyst Based on Nitrogen-Doped Graphene Derived from Edible Sugar and Urea. ACS Appl. Mater. Interfaces 2013, 5, 11108–11114. [28] Yang S.; Feng X.; Wang X.; Müllen K. Graphene-Based Carbon Nitride Nanosheets as Efficient Metal-Free Electrocatalysts for Oxygen Reduction Reactions. Angew. Chem. Int. Ed. 2011, 50, 5339–5343. [29] Zhao A.; Masa J.; Muhler M.; Schuhmann W.; Xia W. N-Doped Carbon Synthesized from N-Containing Polymers as Metal-Free Catalysts for the Oxygen Reduction under Alkaline Conditions. Electrochim. Acta 2013, 98, 139–145. [30] Ramakrishnan P.; Park S.-G.; Shanmugam S. Three-Dimensional Hierarchical Nitrogen-Doped Arch and Hollow Nanocarbons: Morphological Influences on Supercapacitor Applications. J. Mater. Chem. A 2015, 3, 16242–16250. [31] Silva R.; Voiry D.; Chhowalla M.; Asefa T. Efficient Metal-Free Electrocatalysts for Oxygen Reduction: Polyaniline-Derived N-and O-Doped Mesoporous Carbons. J. Am. Chem. Soc. 2013, 135, 7823–7826.

25 ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

[32] Zhang H.; Zhou Y.; Li C.; Chen S.; Liu L.; Liu S.; Yao H.; Hou H. Porous Nitrogen Doped Carbon Foam with Excellent Resilience for Self-Supported Oxygen Reduction Catalyst, Carbon 2015, 95, 388–395. [33] Li Y.; Zhou W.; Wang H.; Xie L.; Liang Y.; Wei F.; Idrobo J.-C.; Pennycook S. J.; Dai H. An Oxygen Reduction Electrocatalyst Based on Carbon Nanotube-Graphene Complexes. Nat. Nanotechnol. 2012, 7, 394–400. [34] Banks C. E.; Crossley A.; Salter C.; Wilkins S. J.; Compton R. G. Carbon Nanotubes Contain Metal Impurities Which are Responsible for the “Electrocatalysis” Seen at Some Nanotube-Modified Electrodes. Angew. Chem. Int. Ed. 2006, 45, 2533–2537. [35] Ambrosi A.; Chee S.Y.; Khezri B.; Webster R. D.; Sofer Z.;Pumera M. Metallic Impurities in Graphenes Prepared from Graphite Can Dramatically Influence Their Properties. Angew. Chem. 2012, 124, 515–518. [36] Lu Y., Wang X., Wang M.; Kong L., Zhao J. 1, 10-Phenanthroline Metal Complex Covalently Bonding to Poly-(Pyrrole-3-Carboxylic Acid)-Coated Carbon: An Efficient Electrocatalyst for Oxygen Reduction. Electrochim. Acta 2015, 180, 86–95. [37] Catalan D. P.; Morales E.; Smit M. A.; Acosta J. L. Electrocatalytic Activity towards Oxygen Reduction of Mesoporous Carbon/Conducting Polymer Composites Application to PEM Fuel Cells. J. New Mater. Electrochem. Syst. 2009, 12,115–118. [38] Jurkschat K.; Ji X.; Crossley A.; Compton R. G.; Banks C. E. Super-Washing Does Not Leave Single Walled Carbon Nanotubes Iron-Free. Analyst 2007, 132, 21–23.

26 ACS Paragon Plus Environment

Page 26 of 31

Page 27 of 31

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

[39] Wang L.; Ambrosi A.; Pumera M. “Metal-Free” Catalytic Oxygen Reduction Reaction on Heteroaton-Doped Graphene is Caused by Trace Metal Impurities. Angew. Chem. 2013, 125, 14063–14066. [40] Banks C. E.; Crossley A.; Salter C.; Wilkins S. J.; Compton R. G. Carbon Nanotubes Contain Metal Impurities Which Are Responsible for the “Electrocatalysis” Seen at Some Nanotube-Modified Electrodes. Angew. Chem. Int. Ed. 2006, 45, 2533 –2537. [41] Brüller S.; Liang H. W.; Kramm U. I.; Krumpfer J. W.; Feng X. L.; Müllen K. Bimetallic Porous Porphyrin Polymer-Derived Non-Precious Metal Electrocatalysts for Oxygen Reduction Reactions. J. Mater. Chem. A 2015, 3, 23799–23808. [42] Lu G.; Zhu Y.; Xu K.; Jin Y.; Ren Z. J.; Liu Z.; Zhang W. Metallated Porphyrin Based Porous Organic Polymers as Efficient Electrocatalysts. Nanoscale 2015, 7, 18271–18277. [43] Wu Z. S.; Chen L.; Liu J.; Parvez K.; Liang H.; Shu J.; Sachdev H.; Graf R.; Feng X.; Müllen K. High-Performance Electrocatalysts for Oxygen Reduction Derived from Cobalt Porphyrin-Based Conjugated Mesoporous Polymers. Adv. Mater. 2014, 26, 1450–1455. [44] Yuan S.; Shui J. L.; Grabstanowicz L.; Chen C.; Commet S.; Reprogle B.; Xu T.; Yu L.; Liu D. J. A highly Active and Support-Free Oxygen Reduction Catalyst Prepared from Ultrahigh-Surface-Area Porous Polyporphyrin. Angew. Chem. Int. Ed. 2013, 52, 8349–8353. [45] Su Y.; Zhu Y.; Jiang H.; Shen J.; Yang X.; Zou W.; Chen J.; Li C. Cobalt Nanoparticles Embedded in N-Doped Carbon as an Efficient Bifunctional Electrocatalyst for Oxygen Reduction and Evolution Reactions. Nanoscale 2014, 6, 15080–15089.

27 ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

[46] Yang M.; Chen H.; Yang D.; Gao Y.; Li H. Using Nitrogen-Rich Polymeric Network and Iron (II) Acetate as Precursors to Synthesize Highly Efficient Electrocatalyst for Oxygen Reduction Reaction in Alkaline Media. J. Power Sources 2016, 307, 152–159. [47] Saravanan C.; Shekhar R. C.; Palaniappan S. Synthesis of Polypyrrole Using Benzoyl Peroxide as a Novel Oxidizing Agent. Macromol. Chem. Phys. 2006, 207, 342–348. [48] Tan Y.; Ghandi K. Kinetics and Mechanism of Pyrrole Chemical Polymerization. Synth. Met. 2013, 175, 183–191. [49] Guyard L.; Hapiot P.; Neta P. Redox Chmistry of Bipyrroles: Further Insights into the Oxidative Polymerization Mechanism of Pyrrole and Oligopyrroles. J. Phys. Chem. B. 1997, 101, 5698–5706. [50] Sing K. S. W.; Everett D. H.; Haul R. A. W.; Moscou L.; Pierotti R. A.; Rouquerol J.; Siemieniewska T. Physical and Biophysical Chemistry Division Commission on Colloid and Surface Chemistry Including Catalysis. Pure Appl. Chem. 1985, 57, 603–619. [51] Groen J. C.; Peffer L. A. A.; Pérez-Ramı́rez J. Pore Size Determination in Modified Micro-and Mesoporous Materials. Pitfalls and Limitations in Gas Adsorption Data Analysis. Microporous Mesoporous Mater. 2003, 60, 1–17. [52] Liao Y.; Gao Y.; Zhu S.; Zheng J.; Chen Z.; Yin C.; Lou X.; Zhang D. Facile Fabrication of N-Doped Graphene as Efficient Electrocatalyst for Oxygen Reduction Reaction. ACS Appl. Mater. Interfaces 2015, 7, 19619–19625.

28 ACS Paragon Plus Environment

Page 28 of 31

Page 29 of 31

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

[53] Jiang Z.; Zhao X.; Tian X.; Luo L.; Fang J.; Gao H.; Jiang Z.-J. Hydrothermal Synthesis of Boron and Nitrogen Codoped Hollow Graphene Microspheres with Enhanced Electrocatalytic Activity for Oxygen Reduction Reaction. ACS Appl. Mater. Interfaces 2015, 7, 19398–19407. [54] Wu J.; Li W.; Higgins D.; Chen Z. Heat-Treated Nonprecious Catalyst Using Fe and Nitrogen-Rich 2, 3, 7, 8-Tetra (pyridin-2-yl) pyrazino [2, 3-g] quinoxaline Coordinated Complex for Oxygen Reduction Reaction in PEM Fuel Cells. J. Phys. Chem. C 2011, 115, 18856–18862. [55] Arechederra R. L.; Artyushkova K.; Atanassov P.; Minteer S. D. Growth of Phthalocyanine Doped and Undoped Nanotubes Using Mild Synthesis Conditions for Development of Novel Oxygen Reduction Catalysts. ACS Appl. Mater. Interfaces 2010, 2, 3295–3302. [56] Wang S.; Yu D.; Da L. Polyelectrolyte Functionalized Carbon Nanotubes as Efficient Metal-Free Electrocatalysts for Oxygen Reduction. J. Am. Chem. Soc. 2011, 133, 5182–5185. [57] Lai L.; Potts J. R.; Zhan D.; Wang L.; Poh C. K.; Tang C.; Gong H.; Shen Z.; Lin J.; Ruoff R. S. Exploration of the Active Center Structure of Nitrogen-Doped Graphene-Based Catalysts for Oxygen Reduction Reaction, Energy Environ. Sci. 2012, 5, 7936–7942. [58] Ai K.; Liu Y.; Ruan C.; Lu L.; Lu G. Sp2C-Dominant N-Doped Carbon Sub-Micrometer Spheres with a Tunable Size: a Versatile Platform for Highly Efficient Oxygen-Reduction Catalysts. Adv. Mater. 2013, 25, 998–1003. [59] Niwa H.; Horiba K.; Harada Y.; Oshima M.; Ikeda T.; Terakura K.; Ozaki J.-I, Miyata S. X-Ray Absorption Analysis of Nitrogen Contribution to Oxygen Reduction Reaction in Carbon Alloy Cathode Catalysts for Polymer Electrolyte Fuel Cells. J. Power Sources 2009, 187, 93–97. [60] Yeager E. Electrocatalysts for O2 Reduction. Electrochim. Acta 1984, 29, 1527–1537.

29 ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

[61] Radovic L. R. Carbons for Electrochemical Energy Storage and Conversion Systems; Beguin F., Frackowiak E., Eds.; CRC Press: Boca Raton, 2009; Chapter 5, pp. 163–219. [62] Zhong R. S.; Qin Y. H.; Niu D. F.; Tian J. W.; Zhang X. S.; Zhou X. G.; Sun S. G.; Yuan W. K. Effect of Carbon Nanofiber Surface Functional Groups on Oxygen Reduction in Alkaline Solution. J. Power Sources 2013, 225, 192–199. [63] Pels J. R.; Kapteijn F.; Moulijn J. A.; Zhu Q.; Thomas K. M. Evolution of Nitrogen Functionalities in Carbonaceous Materials During Pyrolysis. Carbon 1995, 33, 1641–1653. [64] Balbuena P. B.; Altomare D.; Agapito L.; Seminario J. M. Theoretical Analysis of Oxygen Adsorption on Pt-Based Clusters Alloyed with Co, Ni, or Cr Embedded in a Pt Matrix. J. Phys. Chem. B 2003, 107, 13671–13680.

30 ACS Paragon Plus Environment

Page 30 of 31

Page 31 of 31

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

Table of Contents

31 ACS Paragon Plus Environment