Release of Particulate Iron Sulfide during Shale ... - ACS Publications

Dec 11, 2017 - images were obtained and then stitched together in Photoshop to create mosaics with areas ranging from ∼500 000 μm2 to. ∼5 000 000...
0 downloads 12 Views 1MB Size
Subscriber access provided by READING UNIV

Article

Release of particulate iron sulfide during shale-fluid interaction Yevgeny Kreisserman, and Simon Emmanuel Environ. Sci. Technol., Just Accepted Manuscript • DOI: 10.1021/acs.est.7b05350 • Publication Date (Web): 11 Dec 2017 Downloaded from http://pubs.acs.org on December 13, 2017

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Environmental Science & Technology is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 18

Environmental Science & Technology

2

Release of particulate iron sulfide during shale-fluid interaction

3

Yevgeny Kreisserman, Simon Emmanuel*

4

Institute of Earth Sciences, The Hebrew University, Jerusalem 91904, Israel

1

5 6 7

*

8

Abstract

9

During hydraulic fracturing, a technique often used to extract hydrocarbons from

corresponding author, email: [email protected]

10

shales, large volumes of water are injected into the subsurface. Although the injected

11

fluid typically contains various reagents, it can become further contaminated by

12

interaction with minerals present in the rocks. Pyrite, which is common in organic-

13

rich shales, is a potential source of toxic elements, including arsenic and lead, and it is

14

generally thought that for these elements to become mobilized, pyrite must first

15

dissolve. Here, we use atomic force microscopy and environmental scanning electron

16

microscopy to show that during fluid-rock interaction, the dissolution of carbonate

17

minerals in Eagle Ford shale leads to the physical detachment, and mobilization, of

18

embedded pyrite grains. In experiments carried out over a range of pH, salinity, and

19

temperature we found that in all cases pyrite particles became detached from the shale

20

surfaces. On average, the amount of pyrite detached was equivalent to 6.5×10-11 mol

21

m-2 s-1, which is over an order of magnitude greater than the rate of pyrite oxidation

22

expected under similar conditions. This result suggests that mechanical detachment of

23

pyrite grains could be an important pathway for the mobilization of arsenic in

24

hydraulic fracturing operations and in groundwater systems containing shales.

25 26 27

1. Introduction

28

Hydraulic fracturing is a commonly used technique to extract hydrocarbons from

29

organic-rich shale formations deep in the subsurface. The method involves the

30

injection of fluid into the shale, which induces rock fracture and the release of trapped

31

oil and gas. The efficiency of this technique has increased significantly over the last

32

decade due to the introduction of horizontal drilling techniques, and the number of 1 ACS Paragon Plus Environment

Environmental Science & Technology

33

such unconventional wells has jumped from 26,000 in 2000 to 300,000 by 20151.

34

Although effective at extracting hydrocarbons, the use of hydraulic fracturing

35

techniques has been controversial due to its potential environmental effects, which

36

include the contamination of groundwater and surface water2–8

37

One possible pathway for water reservoirs to become contaminated is via

38

mixing with fracture fluids5,9. Such fluids contain contaminants both because of the

39

reagents that are added prior to injection10,9, and the organic and inorganic

40

contaminants that they acquire during water-rock interaction11,12. While the release of

41

organic contaminants has been the focus of much recent research 13,2,14–18, the way in

42

which inorganic contaminants enter the mobile fluid phase has received less attention.

43

Ultimately, a better understanding of these pathways could help operators design

44

injection fluids that will help minimize the levels of contamination.

45

Fluids in contact with shales can react chemically with mineral assemblages

46

within the rock, either by leaching sorbed species from mineral surfaces, or dissolving

47

mineral phases. Some of these dissolving minerals, such as calcium carbonate, are

48

relatively innocuous, while others, such as iron sulfides, can release toxic species into

49

the fluid19,20. Dissolution of pyrite (FeS2) - which is a common component in organic

50

rich shales, and typically has high concentrations of heavy metals and arsenic - has

51

been implicated in the widespread contamination of groundwater in Bangladesh and

52

India21,22,23. Furthermore, pyrite oxidation is often the main cause of pollution caused

53

by acid mine drainage19,24.

54

In addition to desorption and dissolution, fluid-rock interaction can also lead

55

to the physical detachment of mineral grains and particles from the rock surface. It

56

has been demonstrated that tiny clay and carbonate particles can be mobilized during

57

the dissolution of limestone25,26, and a similar mechanism could also operate in shales.

58

Importantly, colloidal particles released via this mechanism could be transported with

59

the flowing fluid phase, contributing to the overall level of contamination. However,

60

at present little is known about the amount of particulate matter that is released during

61

shale-water interaction and what factors control its release.

62

In this paper, we quantify the release of particulate pyrite during experiments that

63

simulate the interaction of shale and water in the subsurface. In addition, we

64

determine the effect of different conditions such as salinity, temperature, and flow rate

65

on the rate of pyrite release. Finally, we discuss how our findings could be used to

2 ACS Paragon Plus Environment

Page 2 of 18

Page 3 of 18

Environmental Science & Technology

66

assess groundwater contamination from organic rich shales and hydraulic fracturing

67

operations.

68 69

2. Materials and methods

70

2.1 Sample characterization

71

We carried out a series of experiments on shale from the Eagle Ford formation from

72

the Del Rio quarry in Texas. For the last decade, the Eagle Ford shale has been one of

73

the most actively drilled plays in North America27. X-ray diffraction analyses (Bruker

74

D8 Advance) on our samples indicate that calcite is the dominant mineral (61%;

75

Table 1), and that pyrite is present in minor amounts (0.8%). Using RockEval, the

76

total organic content (TOC) was determined to be 5.7%, which is within the range

77

reported for the Eagle Ford formation28.

78 79

2.2 In situ atomic force microscopy (AFM) imaging experiments

80

To provide high resolution in situ imaging during fluid-rock interaction, and to

81

simulate the way a fracture surface might behave, we performed a limited number of

82

experiments with atomic force microscopy (AFM; Figure S1a). This technique has

83

been used successfully to examine grain detachment in carbonate rocks in fluid

84

environments25,29, although the experiments shown here are the first to be reported for

85

shale samples. Samples were prepared from a 5.5 mm diameter shale core that was

86

embedded in a Plexiglas disk and then polished by hand using a diamond-impregnated

87

textile (Policloth; Fischer). The surfaces were then rinsed with deionized water and

88

dried in air.

89

Once prepared, the sample was sealed in a fluid imaging cell on the AFM scanner

90

(Veeco Multimode 8 AFM with a NanoScope V controller and NanoScope 8.15

91

software). Deionized water equilibrated with the atmosphere (pH 5.5) was injected

92

constantly into the system at a rate of 2 ml hr−1. To track the evolution of the surface

93

of the shale, the sample was imaged continuously during the experiments with silicon

94

nitride probes (Bruker ScanAsyst Fluid+). Scans of regions up to 20 μm × 20 μm

95

were performed at a line rate of 1 Hz with a resolution of 256 × 256 pixels using the

96

Peakforce ScanAsyst non-contact imaging method. At this rate, image acquisition

97

takes 4 min 16 s. The imaging mode we used produced a topographical map which

3 ACS Paragon Plus Environment

Environmental Science & Technology

98

provides the precise height of the surface. The surfaces of the samples were imaged

99

both before and after the experiments using environmental scanning electron

100

microscopy (ESEM; FEI Quanta 200), and the chemical identification of individual

101

grains was made using energy dispersive X-ray spectroscopy (EDS).

102 103

2.3 Ex-situ environmental scanning electron microscopy (ESEM) experiments

104

Due to the increasing surface roughness during the fluid experiments, the duration of

105

the AFM measurements was limited to several hours. To determine changes to the

106

surface over longer times, we developed a protocol in which the sample was sealed in

107

a Plexiglass flow-through cell into which a fluid was injected at a constant rate (15 ml

108

h-1) using a peristaltic pump (Figure S1b). The residence time of water in the fluid cell

109

was estimated to be approximately 40 seconds. During the experiment, the fluid cells

110

were immersed in a refrigerated circulating bath which maintained temperatures at 25

111

±0.01°C. Samples were exposed to the fluid for a total of 6-9 days, after which the

112

experiments were terminated.

113

At the beginning and end of each experiment, the samples were imaged using E-

114

SEM in the backscattered electron (BSE) mode. By comparing the before and after

115

images, we were able to identify bright grains that had been detached during the

116

experiment. Using EDS analysis to identify the composition of individual grains, we

117

found that >95% of the bright grains in the BSE images comprised pyrite. For each

118

sample, multiple images were obtained and then stitched together in Photoshop to

119

create mosaics with areas ranging from ~500,000 m2 to ~5,000,000 m2.

120

Environmental conditions in the subsurface, as well as the chemistry of injected

121

fluids, can vary significantly; to determine the influence of pH, salinity, and

122

temperature on the release of pyrite particles, these three parameters were varied in

123

the range 3-9, 0-35 g l-1, and 25-60oC respectively. To assess the variability of our

124

results, repeat experiments were carried out, with a total of 16 experiments being

125

performed (Table 2).

126

To quantify the number and size of pyrite grains being detached from the surface,

127

we developed a workflow based around the Matlab Image Processing Toolbox. The

128

workflow involved four main steps: (i) registration of the before and after gray scale

129

BSE images; (ii) subtraction of the before image from the after image; (iii) application

130

of an intensity threshold to identify regions which had become significantly darker, 4 ACS Paragon Plus Environment

Page 4 of 18

Page 5 of 18

Environmental Science & Technology

131

which represented the possible formation of a pit in the surface; and (iv) identification

132

of “blobs” in the thresholded image that were above a certain size, possessed a

133

specified level of sphericity, and which had a similar level of brightness to pyrite in

134

the original image. To filter out false positive identifications, each “blob” was

135

inspected manually to determine whether or not a pyrite grain had indeed been

136

removed. By normalizing to the total surface imaged, a minimum estimate was

137

obtained for the number grains removed per unit area of shale surface with time. An

138

equivalent grain diameter, D, was calculated from the area of each pyrite grain, Apy,

139

according to D =(4Apy/)1/2. Assuming that the grains were spherical, the volume for

140

each grain was calculated, and the molar amount was determined by dividing the

141

volume by the molar volume of pyrite (2.39×10-5 m3 mol-1).

142

To provide an indication of the structural and mineralogical changes occurring

143

beneath the surface of the shale, we used a focused ion beam – scanning electron

144

microscope (FIB-SEM; Raith e_LiNE - e-Beam Lithography System) to create, and

145

then image, a 40 m wide by 20 m deep cross section. To determine the mineralogy

146

of the grains exposed in the cross section, elemental maps of the cross section were

147

obtained using energy dispersive X-ray spectroscopy.

148 149

3. Results and discussion

150

3.1 Pyrite dissolution and pyrite grain detachment

151

During the in situ atomic force microscope experiments, we observed relatively rapid

152

dissolution of carbonate phases, and even instances of carbonate grain detachment,

153

which is consistent with the behavior reported for fine grain calcareous rocks30,31. By

154

contrast, pyrite framboids and individual grains in the images did not appear to

155

undergo significant chemical dissolution during the course of the experiments (Figure

156

1). Over a 3 hour experiment, we estimated pyrite surfaces to dissolve less than 10 nm

157

(the estimated uncertainty for the topographic measurements), indicating that

158

dissolution rates must be below 10-3 nm s-1. From the rate the law proposed by

159

Williamsen and Rimstidt (1994)32,

160

,

Equation 1

is the dissolved oxygen concentration (estimated from Henry’s law to be

161

where

162

2.7×10-4 mol l-1) and

163

oxidation for our experimental conditions is calculated to be 3.8×10-10 mol m-2 s-1.

is the proton concentration (10-5 mol l-1), the rate of pyrite

5 ACS Paragon Plus Environment

Environmental Science & Technology

164

Taking the molar volume of pyrite as 2.39×10-5 m3 mol-1, and assuming that all

165

oxidized pyrite becomes effectively dissolved, pyrite surfaces should retreat at a

166

maximal rate of ~9×10-6 nm s-1, which is entirely consistent with the upper bound we

167

estimate from our measurements.

168

Despite the very low rate of pyrite dissolution, we did observe instances of

169

physical detachment of pyrite grains from the surface of the Eagle Ford shale. In

170

Figure 1, a 4 m pyrite grain - surrounded by calcite – is visible in the first AFM

171

image but is clearly absent from an image of the same area taken around 4 minutes

172

later (Figure 1d). By contrast, no change is seen in the pyrite framboid present in the

173

same image, indicating that rapid dissolution cannot account for the disappearance of

174

the grain.

175

In the ex-situ experiments, numerous instances of pyrite grain detachment

176

were observed, and these grains were almost always embedded in calcite at the

177

beginning of the experiment (Figure 2). By contrast, we did not observe any

178

mobilization of pyrite grains surrounded by clay minerals and organic matter,

179

suggesting that the dissolution of reactive carbonate phases is a critical step in the

180

mobilization of pyrite grains. The effect of carbonate dissolution on the structure and

181

porosity of the shale is evident from the FIB-SEM images (Figure 3). In the cross

182

section cut at the surface of the sample that had not been exposed to fluid, pyrite

183

framboids can be seen to be embedded in calcite. In addition, only a low level of

184

porosity is visible. By contrast, in the cross section of the sample exposed to fluid for

185

9 days, much less calcite is present and a well developed porous network has

186

developed.

187 188

3.2 Effect of salinity, temperature, and flow rate on pyrite grain detachment

189

To determine the effect of environmental conditions on the amount of pyrite released,

190

we carried out a series of experiments at varying pH, salinity, and temperature. Under

191

all the different conditions, numerous instances of pyrite grain detachment were

192

observed (Table 2; Figure 4). However, we observed significant variance between

193

experiments carried out under identical conditions, making it impossible to identify

194

any statistically significant trends (Figure 5). Such high variability is likely to be due

195

to the difficulty of imaging representative regions in shale samples that exhibit a high

196

degree of mineralogical and textural heterogeneity. Carrying out additional

6 ACS Paragon Plus Environment

Page 6 of 18

Page 7 of 18

Environmental Science & Technology

197

experiments, or imaging larger regions, could help reduce this uncertainty in future

198

studies. Despite this high variability, what is clear from the experiments is that pyrite

199

grain detachment occurs under a wide range of conditions that are likely to be

200

encountered during hydraulic fracturing operations, as well as in other environmental

201

scenarios.

202

3.3 Implications of pyrite grain detachment for environmental systems

203

When normalized to the area of shale exposed to fluid-rock interaction, the rate of

204

release of particulate pyrite in our experiments is estimated to be in the range 2.8×10-

205

12

206

mol m-2 s-1). Assuming that the rate of pyrite oxidation represents the maximal rate of

207

dissolution (i.e., all oxidized pyrite enters the solution), multiplying the rate of

208

oxidation, calculated from Equation 1, by the proportion of the shale surface at which

209

pyrite is exposed (0.8%) yields the effective rate of dissolution to be approximately

210

3.0×10-12 mol m-2 s-1. Thus, in our experiments, the detachment of pyrite is on average

211

22 times greater than the flux expected from pyrite oxidation. This simple calculation

212

suggests that the physical detachment of pyrite grains could represent a significant

213

mechanism for the mobilization of pyrite in subsurface systems. Crucially, pyrite

214

often contains arsenic and toxic metals. As a result, during hydraulic fracturing

215

operations, as well as in other groundwater systems exposed to pyrite (e.g., acid mine

216

drainage), the mobility of these elements may be strongly influenced by the transport

217

of colloidal iron sulfide particles.

218

– 2.0×10-10 mol m-2 s-1, with an average of 6.5×10-11 mol m-2 s-1 (1 = 6.5×10-11

While our analysis provides insight into the mechanisms controlling pyrite

219

mobilization, there are some clear limitations. Firstly, the rates of carbonate

220

dissolution in our laboratory experiments may be more rapid than those found under

221

field conditions33, especially after prolonged water-rock interaction. Thus, the actual

222

rate of particulate release in the field, especially under high pH conditions, could be

223

lower than that reported here. Moreover, carbonate minerals are not the dominant

224

phase in many shales, and determining if pyrite particles detach from shales with

225

different mineral assemblages will help us to assess the full extent of this mechanism

226

in hydrogeological systems. Finally, even if the release of pyrite particles is

227

widespread, it is unclear how far they can be transported within a real fracture

228

network before settling or being oxidized. Addressing these questions, and looking for

7 ACS Paragon Plus Environment

Environmental Science & Technology

229

evidence for the mobilization of pyrite particles in the field, is the focus of ongoing

230

research.

231 232

Acknowledgments

233

We thank the Israel Science Foundation for generous financial support and the Israel

234

Ministry of National Infrastructures, Energy and Water. We also thank two

235

anonymous reviewers and the associate editor, Richard Valentine, for their helpful

236

comments.

237 238

References

239 240

(1)

Energy Information Agency. Hydraulically fractured wells provide two-thirds of U.S. natural gas production. EIA Today Energy 2016, 1–2.

241 242 243

(2)

Osborn, S. G.; Vengosh, A.; Warner, N. R.; Jackson, R. B. Methane contamination of drinking water accompanying gas-well drilling and hydraulic fracturing. Proc. Natl. Acad. Sci. 2011, 108 (37), E665–E666.

244 245 246

(3)

Jackson, R. B.; Vengosh, A.; Carey, J. W.; Davies, R. J.; Darrah, T. H.; Sullivan, F. O.; Gabrielle, P. The environmental costs and benefits of fracking. Annu. Rev. Environ. Resour. 2014, 39, 327–362.

247 248 249

(4)

Vengosh, A.; Mitch, W. A.; McKenzie, L. M. Environmental and human impacts of unconventional energy development. Environ. Sci. Technol. 2017, 51 (18), 10271–10273.

250 251 252

(5)

Vengosh, A.; Warner, N.; Jackson, R.; Darrah, T. The effects of shale gas exploration and hydraulic fracturing on the quality of water resources in the United States. Procedia Earth Planet. Sci. 2013, 7, 863–866.

253 254 255

(6)

Sovacool, B. K. Cornucopia or curse? Reviewing the costs and benefits of shale gas hydraulic fracturing (fracking). Renew. Sustain. Energy Rev. 2014, 37, 249–264.

256 257 258

(7)

Norris, J. Q.; Turcotte, D. L.; Moores, E. M.; Brodsky, E. E.; Rundle, J. B. Fracking in tight shales: What is it, what does it accomplish, and what are its consequences? Annu. Rev. Earth Planet. Sci. 2016, 44 (1), 321–351.

259 260 261

(8)

Entrekin, S.; Evans-White, M.; Johnson, B.; Hagenbuch, E. Rapid expansion of natural gas development poses a threat to surface waters. Front. Ecol. Environ. 2011, 9 (9), 503–511.

262 263 264

(9)

Gordalla, B. C.; Ewers, U.; Frimmel, F. H. Hydraulic fracturing: A toxicological threat for groundwater and drinking-water? Environ. Earth Sci. 2013, 70 (8), 3875–3893.

265 266 267

(10)

Gregory, K. B.; Vidic, R. D.; Dzombak, D. A. Water management challenges associated with the production of shale gas by hydraulic fracturing. Elements 2011, 7 (3), 181–186.

268 269

(11)

Li, Y.; Huang, T.; Pang, Z.; Jin, C. Geochemical processes during hydraulic fracturing: a water-rock interaction experiment and field test study. Geosci. J. 8 ACS Paragon Plus Environment

Page 8 of 18

Page 9 of 18

Environmental Science & Technology

270

2017, 21 (5), 753–763.

271 272 273 274

(12)

Warner, N. R.; Darrah, T. H.; Jackson, R. B.; Millot, R.; Kloppmann, W.; Vengosh, A. New tracers identify hydraulic fracturing fluids and accidental releases from oil and gas operations. Environ. Sci. Technol. 2014, 48 (21), 12552–12560.

275 276 277

(13)

Vidic, R.; Brantley, S.; Vandenbossche, J.; Yoxtheimer, D.; Abad, J. Impact of shale gas development on regional water quality. Science. 2013, 340 (6134), e1235009.

278 279 280

(14)

Osborn, S. G.; Vengosh, A.; Warner, N. R.; Jackson, R. B. Methane contamination of drinking water accompanying gas-well drilling and hydraulic fracturing. Proc. Natl. Acad. Sci. U. S. A. 2011, 108 (20), 8172–8176.

281 282

(15)

Schon, S. C. Hydraulic fracturing not responsible for methane migration. Proc. Natl. Acad. Sci. U. S. A. 2011, 108 (37), E664.

283 284 285

(16)

Davies, R. J. Methane contamination of drinking water caused by hydraulic fracturing remains unproven. Proc. Natl. Acad. Sci. 2011, 108 (43), E871– E871.

286 287 288 289

(17)

Darrah, T. H.; Vengosh, A.; Jackson, R. B.; Warner, N. R.; Poreda, R. J. Noble gases identify the mechanisms of fugitive gas contamination in drinking-water wells overlying the Marcellus and Barnett Shales. Proc. Natl. Acad. Sci. 2014, 111 (39), 14076–14081.

290 291 292 293

(18)

Jackson, R. B.; Vengosh, A.; Darrah, T. H.; Warner, N. R.; Down, A.; Poreda, R. J.; Oshborn, S. G.; Zhao, K.; Karr, J. D. Increased stray gas abundance in a subset of drkng water wells. Proc. Natl. Acad. Sci. U. S. A. 2013, 110 (28), 11250–11255.

294 295 296 297 298

(19)

Fontenot, B. E.; Hunt, L. R.; Hildenbrand, Z. L.; Carlton, D. D.; Oka, H.; Walton, J. L.; Hopkins, D.; Osorio, A.; Bjorndal, B.; Hu, Q. H.; Shug, K. A. An evaluation of water quality in private drinking water wells near natural gas extraction sites in the Barnett shale formation. Environ. Sci. Technol. 2013, 47 (17), 10032–10040.

299 300 301

(20)

Paikaray, S. Environmental hazards of arsenic associated with black shales: A review on geochemistry, enrichment and leaching mechanism. Rev. Environ. Sci. Biotechnol. 2012, 11 (3), 289–303.

302 303 304

(21)

Smedley, P. L. Arsenic in groundwater - south and east Asia. In Arsenic in Ground Water; Welch, A. H., Stollenwerk, K. G., Eds.; Springer US: Boston, MA, 2003; Vol. 296.

305 306 307

(22)

Nickson, R. T.; Mcarthur, J. M.; Ravenscroft, P.; Burgess, W. G.; Ahmed, K. M. Mechanism of arsenic release to groundwater, Bangladesh and West Bengal. Appl. Geochemistry 2000, 15 (4), 403–413.

308 309

(23)

Karim, M. M. Arsenic in groundwater and health problems in Bangladesh. Water Res. 2000, 34 (1), 304–310.

310 311

(24)

Akcil, A.; Koldas, S. Acid Mine Drainage (AMD): causes, treatment and case studies. J. Clean. Prod. 2006, 14 (12–13 SPEC. ISS.), 1139–1145.

312 313

(25)

Emmanuel, S.; Levenson, Y. Limestone weathering rates accelerated by micron-scale grain detachment. Geology 2014, 42 (9), 751–754.

314

(26)

Ellis, B. R.; Fitts, J. P.; Bromhal, G. S.; McIntyre, D. L.; Tappero, R.; Peters, 9 ACS Paragon Plus Environment

Environmental Science & Technology

315 316

C. a. Dissolution-driven permeability reduction of a fractured carbonate caprock. Environ. Eng. Sci. 2013, 30 (4), 187–193.

317 318 319

(27)

Okeahialam, I.; Yang, M.; Shinde, D. B.; Sahai, V.; Araque-Martinez, A.; Rai, R. Completion optimization under constraints: An Eagle Ford shale case study. SPE Production & Operations 2017: 32(02)128-136.

320 321 322 323

(28)

Quirein, J.; Murphy, E.; Praznik, G.; Witkowsky, J.; Shannon, S.; Buller, D. A Comparison of core and well log data to evaluate porosity, TOC, and hydrocarbon volume in the Eagle Ford shale. SPE Annu. Tech. Conf. Exhib. 2012, SPE-159904-MS.

324 325 326

(29)

Levenson, Y.; Emmanuel, S. Quantifying micron-scale grain detachment during weathering experiments on limestone. Geochim. Cosmochim. Acta 2016, 173, 86–96.

327 328

(30)

Emmanuel, S.; Levenson, Y. Limestone weathering rates accelerated by micron-scale grain detachment. Geology 2014, 42 (9), 751–754.

329 330 331

(31)

Levenson, Y.; Emmanuel, S. Quantifying micron-scale grain detachment during weathering experiments on limestone. Geochim. Cosmochim. Acta 2016, 173, 86–96.

332 333 334

(32)

Williamson, M. A.; Rimstidt, J. D. The kinetics and electrochemical ratedetermining step of aqueous pyrite oxidation. Geochim. Cosmochim. Acta 1994, 58 (24), 5443–5454.

335 336 337

(33)

Levenson, Y.; Ryb, U.; Emmanuel, S. Comparison of field and laboratory weathering rates in carbonate rocks from an Eastern Mediterranean drainage basin. Earth Planet. Sci. Lett. 2017, 465, 176–183.

338 339

11 ACS Paragon Plus Environment

Page 10 of 18

Page 11 of 18

Environmental Science & Technology

340

Figure 1: (a) Backscattered electron microscopy image of a shale surface before fluidrock interaction and (b) after 18 hours of contact with water. While the bright pyrite framboid in the center of the image remains unchanged, the pyrite grain, circled in red, disappears entirely. (c-d) Topographic maps of the same region imaged during the experiment with atomic force microscopy. The time elapsed between the two images is approximately 4 minutes, and the rapidity with which the pyrite grain (circled in red) disappears indicates that it has been physically detached from the surface.

11 ACS Paragon Plus Environment

Environmental Science & Technology

Figure 2: Backscattered electron microscopy images of Eagle Ford shale (a,c,e) before interaction with fluid, and (b,d,f) after fluid contact. Note the complete removal of the pyrite grains circled in red.

12 ACS Paragon Plus Environment

Page 12 of 18

Page 13 of 18

Environmental Science & Technology

Figure 3: Back scattered electron microscopy images of cross sections of Eagle Ford shale (a) in a sample before interaction with fluid, and (b) in a sample exposed to 9 days of fluid flow. In the section imaged before exposure to fluid, pyrite framboids can be seen embedded in calcite and a relatively low level of porosity is present. By contrast, after exposure to fluid, the section is far more porous, presumably as a result of calcite dissolution. EDS analyses confirmed that the light gray phase in each image is pyrite.

13 ACS Paragon Plus Environment

Environmental Science & Technology

Figure 4: (a)-(f) Histograms showing the sizes of pyrite grains released in the experiments. The pH, temperature, and salinity for each series of experiments is indicated. In (g), a summary of all the grains is given.

14 ACS Paragon Plus Environment

Page 14 of 18

Page 15 of 18

Environmental Science & Technology

Figure 5: Rate of pyrite particle release as a function of (a) pH; (b) salinity; and (c) temperature. Each point represents a single experiment. The high variance is probably a result of the heterogeneity of the shale samples and the relatively limited region imaged in each experiment. Unless otherwise indicated, experimental conditions were carried out at a pH of 5.5, at 25oC, and at a salinity of 0 g l-1.

15 ACS Paragon Plus Environment

Environmental Science & Technology

Table 1: Mineral composition in the Eagle Ford shale sample. mineral calcite quartz kaolinite gypsum dolomite pyrite

% by mass 61.3 21.5 9.0 4.7 2.6 0.8

% 6.6 1.3 2.2 2.2 1.1 0.1

16 ACS Paragon Plus Environment

Page 16 of 18

Page 17 of 18

Environmental Science & Technology

Table 2: Summary of experiments. Experiment Salinity pH number [g/l]

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

5.5 5.5 5.5 5.5 3 3 9 9 5.7 5.7 5.8 5.8 6.1 6.1 6.1 6.1

0 0 0 0 0 0 0 0 3.5 3.5 35 35 0 0 0 0

Temperature [°C]

25 25 25 25 25 25 25 25 25 25 25 25 60 60 60 60

Duration Detachments [hr]

223 223 223 223 223 223 223 223 144 144 144 144 143 143 143 143

19 2 7 8 28 33 20 13 39 33 35 11 74 11 8 22

Area 2 [um ]

Detachments 2 per um

Volume of detached 3 pyrite [um ]

Rate of pyrite removal -2 -1 [mol m sec ]

4.7×105 7.1 ×105 8.4 ×105 1.1 ×106 2.6 ×106 1.6 ×106 1.0 ×106 1.7 ×106 3.7 ×106 3.5 ×106 2.9 ×106 3.3 ×106 4.4 ×106 4.4 ×106 4.5 ×106 4.5 ×106

4.1 ×10-5 2.8 ×10-6 8.3 ×10-6 7.6 ×10-6 1.1 ×10-5 2.0 ×10-5 1.9 ×10-5 7.7 ×10-6 1.0 ×10-5 9.3 ×10-6 1.2 ×10-5 3.3 ×10-6 1.7 ×10-5 2.5 ×10-6 1.8 ×10-6 4.8 ×10-6

471 73 126 390 3,711 816 1,243 178 6,738 6,377 6,138 415 10,775 513 157 5,806

5.3 ×10-11 5.4 ×10-12 7.8 ×10-12 1.9 ×10-11 7.3 ×10-11 2.6 ×10-11 6.2 ×10-11 5.5 ×10-12 1.5 ×10-10 1.5 ×10-10 1.7 ×10-10 1.0 ×10-11 2.0 ×10-10 9.4 ×10-12 2.8 ×10-12 1.0 ×10-10

17 ACS Paragon Plus Environment

Environmental Science & Technology

82x37mm (300 x 300 DPI)

ACS Paragon Plus Environment

Page 18 of 18