Rheology of Sodium Polyacrylate as an Emulsifier Employed in

Nov 10, 2014 - (3) This is because the functional properties (viscosity) can be undesirable ... (7-9) It is well-known that application and acceptance...
0 downloads 0 Views 413KB Size
Research Note pubs.acs.org/IECR

Rheology of Sodium Polyacrylate as an Emulsifier Employed in Cosmetic Emulsions Luis Medina-Torres,*,† Fausto Calderas,‡ Guadalupe Sanchez-Olivares,§ and Diola-Marina Nuñez-Ramirez∥ †

Facultad de Química, Departamento de Ingeniería Química, Conjunto E, Universidad Nacional Autónoma de México (UNAM), México, D.F. 04510, México ‡ Instituto de Investigaciones en Materiales, Universidad Nacional Autónoma de México (UNAM), México, D.F. 04510, México § CIATEC, A.C. Omega 201, Fracc.Industrial Delta, CP 37545, León, Gto. México ∥ Departamento de Ingeniería Química y Bioquímica, Instituto Tecnológico de Durango, Felipe Pescador #1803 Ote. CP 34080, Durango, Dgo México ABSTRACT: A set of emulsions containing sodium polyacrylate as emulsifier was prepared. The effect of pH, temperature, and polymer concentration on sample stability was studied. Stability of the sample was evaluated through rheology and the morphology techniques. The sample containing 2% (w/w) sodium polyacrylate exhibited more evident changes in storage G′ and loss G″ moduli with respect to 1% and 1.5% (w/w) samples, evidencing a more structured elastic material, even at high temperatures at which a more stable sample is assumed. For most of the systems studied, the storage modulus (G′) was always higher than the loss modulus (G″) which is attributed to the formation of a strong network arising from the polymer interacting with the oil and aqueous phases; the complexity of this network is related to the action of pH and temperature. These results reveal the conditions at which the polyacrylate offers the best advantages in industrial cosmetic applications, that is, pH levels near 6.5, with a 2% (w/w) polymer concentration and a temperature of 25 °C.

1. INTRODUCTION Emulsions have found a wide range of applications of which the following are certainly worth mentioning: food emulsions, cosmetics, paints, agrochemicals, pharmaceuticals, bitumen emulsions, inks and paper coating, adhesives, and many household products.1 The rheological properties (viscosity, elastic modulus G′, and viscous modulus G″) of emulsion systems are essential physical attributes of these materials.2 The creation of an emulsion goes beyond maintaining the oil and aqueous phase together by the action of an emulsifier.3 This is because the functional properties (viscosity) can be undesirable for the consumer; the product can be too thin (no structure) or too thick (highly structurated). Processing problems are also worth considering; viscosity of the product is an essential parameter in mixing, pumping, and packing the finished product.3,4 Stability issues also affect the shelf life of these products. So, finding the optimum formulation and process conditions becomes critical. The cosmetic and toiletry industries are areas where more new products and constant innovation are registered. This innovation requires hard work from the research and development laboratories where the new products are generated. An example of this constant change is the transition from traditional emulsions to cream-gel formulations,1 in which polymeric emulsifiers are used as thickeners or emulsion stabilizers.3,5 Polyacrylate is a common emulsifier employed to obtain different emulsion structures. Consequently, a variety of applications are possible including face and hand creams (for normal, dry, or oily skin), body milks and lotions, and sun© XXXX American Chemical Society

protective products. Polyacrylate has been used as both an emulsifier as well as a rheology modifier; it is supplied as a dustless powder for ease of handling. It thickens rapidly when added to water and will provide yield strength and viscosity to the system, additionally it stabilizes oil in water emulsions regardless of the oil phase (Figure 1), and it is also more stable

Figure 1. Thickening mechanism, water molecules enter into the polymer matrix, with subsequent swelling.

in terms of sensitivity to pH (as it was observed here) than other synthetic materials. For decades, rheological measurements have been employed in the characterization of emulsion systems.6 These emulsions are pseudoplastic materials (n < 1) identified by their non-Newtonian flow behavior; the onset of flow is product-specific and differs significantly for lotions and creams. For example, in terms of the critical shear stress at the Received: August 29, 2014 Revised: November 7, 2014 Accepted: November 10, 2014

A

dx.doi.org/10.1021/ie503406a | Ind. Eng. Chem. Res. XXXX, XXX, XXX−XXX

Industrial & Engineering Chemistry Research

Research Note

yield point, the emulsion formulation and process varies significantly for creams as compared to lotions. Additionally, flow parameters obtained by continual and/or oscillatory rheological measurements provide information regarding the system colloidal structure and physical stability, that is, internal structure response to flow.7 With emulsions being thermodynamically unstable systems (emulsion systems evolve as time passes and phase separation occurs eventually), the most important factor to be considered in emulsion technology is undoubtedly the evolution of their properties. Therefore, the rheology of emulsions is constantly focusing on its relationship with emulsion stability regarded as the response of the fluid structure to flow and time.8 For all of the aforementioned reasons, rheological properties of emulsions are known to be of great importance. In the case of cosmetic emulsions, these properties are closely related to consumers’ acceptance and as such, represent an important factor for their sales potential. In fact, fulfilling consumer expectations has become imperative in the food and personal care industry. Proper assessment of features related to human perception merits great attention for both scientific and practical reasons.9 The rheological properties of emulsions are influenced by their colloidal structure and therefore can be related to physical properties, and it is a challenging prospect to relate these measurements to consumer perception.7−9 It is well-known that application and acceptance of semisolid products are greatly dependent on the flow properties of the final product.10 When applied on the skin, the material is subjected to deformation so that rheology describes, explains, and measures the material response to that deformation. Rheological measurements are usually performed in order to predict behavior of the product in real conditions during formulation, processing, and application.11−13 This work focuses on the characterization of a cosmetic emulsion using polyacrylate as a synthetic emulsifier through rheological measurements (continuous steady state and oscillatory flow) to evaluate the effect of pH, temperature, and polymer concentration. The rheological properties of the emulsions were investigated in terms of the continuous shear steady state viscosity and the linear viscoelastic response, that is, the evolution of the elastic G′ and viscous G″ moduli. Finally, the dynamic mechanical properties were matched with the emulsion morphology.

Table 1. Cosmetic Emulsion Composition (%, w/w) phase A A A

ingredients

%

deionized water disodium EDTA sodium polyacrylate, hydrogenated polydecene, trideceth-6a mineral oil castoryl maleatea cyclotetrasiloxanea disodium lauriminodipropionate tocopheryl phosphatesa propylene glycol, diazolidinyl urea, iodopropynyl butylcarbamatea

B B B B B total a

Cbp to 100 0.10 1−2 3.00 0.50 0.50 0.30 0.50 100.00

Comercial products, pharmaceutical grade.

2.2. Rheological Measurements. All the rheological measurements were performed with an AG2 (model TA) controlled stress rheometer. Concentric cylinders (25 mm diameter) and parallel plates (25 mm diameter) were used; the gap between the two plates was 0.5 mm in parallel plate. The geometries were selected depending on the viscosity of the emulsion. The emulsions were characterized in steady-shear viscosity function η (γ) and under oscillatory flow. The former was carried out by using a unidirectional steady-shear flow ranging from 1 to 300 1/s, and the latter was accomplished in the linear viscoelastic regime that was previously determined for each of the studied conditions ( G″). This behavior does not hold for the emulsions of pH 4.0, which not only have lower values in their mechanic response (G′ and G″), but they also show that the viscous modulus dominates over the elastic modulus (G″ > G′). This is an indication that there is a critical pH value below which a network structure is not well formed; this is consistent with the steady-shear viscosity results.20−22 The pH value of the emulsion has a great impact on the swelling behavior of the gels.18 Two different behaviors were observed in relation to the pH effect: A significant increment in the viscosity and oscillatory shear moduli of the gel at pH 4−6 which is evidenced by a sol−gel transition (below pH 6, G″ > G″ and above pH 6, G′ > G″) and stabilization of the viscosity at pH 6−7 with a weak gel behavior. A polymer network is formed when an electrical interaction between atoms is present (van der Waals forces, hydrogen D

dx.doi.org/10.1021/ie503406a | Ind. Eng. Chem. Res. XXXX, XXX, XXX−XXX

Industrial & Engineering Chemistry Research

Research Note

heterogeneous system (many particle aggregates domains) corresponding to a pH of 4 which we believe is associated with the decrease in viscosity shown for this system, while at pH 6.5 and 9 (Figure 8b,c), a more homogeneous well-dispersed system is found (few particle aggregates domains and more dispersed particles). This is an indication that there is a critical pH value below which a network structure is not well formed which is consistent with the rheological results. From the micrographs it was evident that the emulsion at pH 4 was the more unstable one and that the emulsions at pH 6.5 and 9 formed a stable particle−particle interaction network. The rheological behavior and morphology results can be attributed to a combination of two factors: The first one is that the lower droplet size results in a reduction of the free energy associated with the strength of the interaction. The second one is that the creation of a larger specific surface area in the fine emulsion will simultaneously be accompanied by a reduction in the amount of unabsorbed polymer. These two factors imply a considerably reduction of flocculation for the emulsions containing the smaller droplets.21 In summary, the viscoelastic behavior linearly increases with the polymer content. The results showed that at low frequency with high-polymer the elastic modulus dominates the viscoelasticity (G′ > G″)21−23 and these results help to identify the conditions in which the polymer offers the best advantages in industrial applications: pH 6.5, polymer concentration of 2% (w/w), and a temperature of 25 °C.

Figure 7. Frequency dependence of the storage module G′ and loss module G″ for different pH values, maintaining 2.0% (w/w) polymer concentration and and temperature at 25 °C.

bonds) and when the polymer content is sufficient for polymer−polymer interactions. These interactions are modified by the concentration of anions or cations such as H+ or OH−. Additionally, as is well known, the temperature increases the movement and vibration of the atoms and as a consequence viscosity and both moduli G″ and G′ are decreased. The different rheological behaviors observed are possibly the results of diverse structural arrangements that are induced by the well-versed conditions, which are finally translated in different mechanical properties (G′ and G″).16−21 Experimental results and modeling are used to explain the rheological behavior of the investigated samples. Results of rheological measurements alone are not sufficient enough to make final conclusions regarding overall emulsion characteristics; yet certain differentiations between different conditions could be made and used as guidelines at various stages of product formulation/reformulation process. 3.3. Microscopy. Finally, images from optic microscopy analysis of the batches of polyacrylate at different pH values investigated are shown in Figure 8. Figure 8a shows a

4. CONCLUSIONS All samples showed shear-thinning behavior. For a polymer concentration of 2.0% (w/w) the mechanic changes are more evident (highest steady-shear viscosity and moduli, G′ and G″) as compared with the other concentrations evaluated. This is due to the formation of a polymer network more stable to the flow; the nature of this network is pH- and temperaturedependent. The viscoelastic response of the studied mixtures increases as the polymer concentration rises, becoming more resistant to deformation even at high temperatures. The pH is a determining factor in the rheological behavior of the emulsions that contain sodium polyacrylate; this is because the rheological properties suffered evident changes related to the stability of the network formed by the polymer. A critical pH value has been encountered to attain a stable network; below this critical pH, network formation is incomplete. These results help to identify the conditions in which the polymer offers the best advantages in industrial applications: pH 6.5, polymer concentration of 2% (w/w), and a temperature of 25 °C. The results confirmed that rheology can be used to differentiate emulsions regarding mechanical properties and the best process conditions can be selected according to the end-use application to obtain tailor-made cosmetics. Skin feel is an important sensory area for cosmetic products.



AUTHOR INFORMATION

Corresponding Author

*E-mail: [email protected]. Tel.: 52-5556225360. Fax: 525556225329. Address: Conjunto E, Ciudad Universitaria, México D.F., 04510, México.

Figure 8. . Microphotographs of the emulsions at different pH values: (a) pH 4.2, (b) pH 6.5, and (c) pH 9, maintaining 2.0% (w/w) polymer concentration and temperature at 25 °C.

Notes

The authors declare no competing financial interest. E

dx.doi.org/10.1021/ie503406a | Ind. Eng. Chem. Res. XXXX, XXX, XXX−XXX

Industrial & Engineering Chemistry Research



Research Note

REFERENCES

(1) Swarbrick, J.; Boylan, J. C. Encyclopedia of Pharmaceutical Technology, 2nd ed.; Marcel Dekker, Inc.: New York, 2001; Vol. 20. (2) Barnes, H. A. Rheology of emulsionsA review. Colloids Surf., A 1994, 91, 89−95. (3) Laba, D., (Ed.), Rheological Properties of Cosmetics and Toiletries; Marcel Dekker, Inc.: New York, 1993; Vol. 13. (4) Bird, R. B. Ed. Dynamics of Polymeric Liquids Fluid Mechanics; John Wiley & Sons: New York, 1972; Vol. 1, Chapter 4. ́ (5) Medina Torres, L.. Estudio reológico del mucilago de nopal y su efecto sinérgico con otros hidrocoloides de uso alimenticio. Ph.D. Thesis, ́ UNAM, Facultad de Quimica: México, 2005. (6) Oguz, O.; Sariisik, S. B. Swelling behavior of poly_acrylamide-cosodium acrylate_ hydrogels in aqueous salt solutions: Theory versus experiments. Eur. Polym. J. 2000, 36, 393−399. (7) Tadros, T. Application of rheology for assessment and prediction of the long-term physical stability of emulsions. Adv. Colloid Interface Sci. 2004, 108−109, 227−258. (8) Gallegos, C.; Franco, J. M. Rheology of food, cosmetics and pharmaceuticals. Curr. Opin. Colloid Interface Sci. 1999, 4 (4), 288− 293. (9) Rossi, G. B.; Berglund, B. Measurement involving human perception and interpretation. Measurement 2011, 44 (5), 815−822. (10) Trapp, M. Is there room for improvement in the emollients for adjuvant therapy. J. Eur. Acad. Derm. Venereol. 2007, 21 (s2), 14−18. (11) Kim, K. H.; Gohtani, S.; Yamano, Y. Effects of oil droplets on physical and sensory properties of o/w emulsion agar gel. J. Texture Stud. 1996, 27 (6), 655−670. (12) Brummer, R.; Godersky, S. Rheological studies to objectify sensations occurring when cosmetic emulsions are applied to the skin. Colloids Surf., A 1999, 152 (1), 89−94. (13) Park, E. K.; Song, K. W. Rheological evaluation of petroleum jelly as a base material in ointment and cream formulations: Steady shear flow behavior. Arch. Pharm. Res. 2010, 33 (1), 141−150. (14) Usui, F.; Maeda, K.; Kusai, A.; Nishimura, K.; Yamamoto, K. Inhibitory effects of water-soluble polymers on precipitation of RS8359. Int. J. Pharm. 1997, 154 (1), 59−66. (15) Mezger, T. G. Ed. The Rheology Handbook: For Users of Rotational and Oscillatory Rheometers; Vincentz Network GmbH & Co. KG: Hannover, Germany, 2006. (16) Bird, R. B.; Armstrong, R. C.; Hassager, O. Eds. Dynamics of Polymeric Liquids, Fluid Mechanics, 1st ed.; John Wiley & Sons: New York, 1977, Vol. 1. (17) Macosko, C. W. Ed. Rheology: Principles, Measurements and Applications; VCH: New York, 1994. (18) Tanaka, T. Phase transition in gels and a single polymer. Polymer 1979, 20 (11), 1404−1412. (19) Siewert, M.; Dressman, J.; Brown, C. K.; Shah, V. P.; Aiache, J. M.; Aoyagi, N.; Williams, R. FIP/AAPS guidelines to dissolution/in vitro release testing of novel/special dosage forms. AAPS Pharm. Sci. Tech 2003, 4 (1), 43−52. (20) Lee, C. H.; Moturi, V.; Lee, Y. Thixotropic property in pharmaceutical formulations. J. Controlled Release 2009, 136 (2), 88− 98. (21) Medina-Torres, L.; Calderas, F.; Gallegos-Infante, J. A.; González-Laredo, R. F.; Rocha-Guzmán, N. Stability of alcoholic emulsions containing different caseinates as a function of temperature and storage time. Colloids Surf., A 2009, 352 (1−3), 38−46. (22) Lyoo, W. S.; Kim, B. C.; Ha, W. S. Rheological and rheo-optical properties of high molecular weight syndiotactic and atactic polyvinylalcohol solutions. Polym. Eng. Sci. 1997, 37 (7), 1259−1265. (23) Ferry, J. D. (Ed.), Viscoelastic Properties of Polymers; John Wiley& Sons Inc.: New York, 1980.

F

dx.doi.org/10.1021/ie503406a | Ind. Eng. Chem. Res. XXXX, XXX, XXX−XXX