Role of Vanadyl Oxygen in Understanding Metallic Behavior of V2O5

Nanomaterials and Sensors Section, Surface and Nanoscience Division, Indira Gandhi Centre for Atomic Research, Homi Bhabha National Institute, ...
1 downloads 0 Views 3MB Size
Article pubs.acs.org/JPCC

Role of Vanadyl Oxygen in Understanding Metallic Behavior of V2O5(001) Nanorods Raktima Basu,* Arun K. Prasad, Sandip Dhara,* and A. Das Nanomaterials and Sensors Section, Surface and Nanoscience Division, Indira Gandhi Centre for Atomic Research, Homi Bhabha National Institute, Kalpakkam-603 102, India S Supporting Information *

ABSTRACT: Vanadium pentoxide (V2O5), the most stable member of vanadium oxide family, exhibits interesting semiconductor to metal transition in the temperature range of 530−560 K. The metallic behavior originates because of the reduction of V2O5 through oxygen vacancies. In the present report, V2O5 nanorods in the orthorhombic phase with crystal orientation of (001) are grown using vapor transport process. Among three nonequivalent oxygen atoms in a VO5 pyramidal formula unit in V2O5 structure, the role of terminal vanadyl oxygen (OI) in the formation of metallic phase above the transition temperature is established from the temperature-dependent Raman spectroscopic studies. The origin of the metallic behavior of V2O5 is also understood due to the breakdown of pdπ bond between OI and nearest V atom instigated by the formation of vanadyl OI vacancy, confirmed from the downward shift of the bottom most split-off conduction bands in the material with increasing temperature.

1. INTRODUCTION

In the present study, we report semiconductor to metal transition of (001)-oriented V2O5 nanorods, grown using vapor transport process. A transition from semiconducting to metallic behavior was recorded in the temperature-dependent I−V measurement. The reversible temperature-dependent Raman spectra were analyzed for the allowed vibrational modes of semiconducting and metallic V2O5 phases to understand the origin of the transition. The change in electronic band structure after the reduction of V2O5, prompting the metallicity in the sample, is discussed using temperature-dependent ultraviolet− visible (UV−vis) absorption spectroscopic studies and thermal activation energy calculations.

One-dimensional transition metal oxides exhibit unique structure−property relationships that help in developing new electronic and photonic devices.1,2 Vanadium is a transition metal ([Ar]3d34s2) with multiple oxidation states leading to various stoichiometric oxides. Vanadium pentoxide (V2O5), which is essentially a semiconductor at room temperature, is the most stable form among them. Although most of vanadium oxides such as VO2, V2O3, V6O13 exhibit metal to insulator transitions (MITs) as a function of temperature, in case of V2O5 it is quite contentious to use the term “MIT”.3 However, there are few reports about transition to metallic phase of V2O5 films around 530 to 553 K and surface metallicity of (001) facet around 340 to 400 K.4−6 The MIT is also reported to be reversible.6 The metallic behavior makes V2O5 applicable as gas sensors,7,8 thermochromic devices,9,10 and optical and electrical switches11 around the transition temperature. The origin of the metallic behavior, however, is still not fully understood. The metallic transition was reported because of the reduction of V2O5 to other lower ordered stoichiometric or nonstoichiometric oxides without any structural change.5,12 In the structure of V2O5 there are three differently coordinated O atoms, namely, OI (vanadyl), OII (bridging), and OIII (chain) (schematic in the Supporting Information Figure S1).13 There is also a dispute in the identification of the oxygen responsible for the reduction as all three OI,6,14 OII,15 and OIII16 are suggested to be the eligible candidates. A structural phase transition from α-V2O5 to metastable γ′-V2O5 with increasing temperature,17 however, is also proposed to explain metallicity above the transition temperature, as γ′-V2O5 resembles conductive Wadsley phase of V4O9.18 © 2016 American Chemical Society

2. EXPERIMENTAL DETAILS V2O5 nanorods were synthesized by vapor transport process using bulk VO2 powder (Sigma-Aldrich, 99%) as source, placed in a high pure (99.99%) alumina boat at the center of the quartz tube reaction chamber, and flowing 20 sccm of Ar (99.9%) as carrier gas. Samples were grown on SiO2/Si (100) using Au thin film (2 nm) as catalyst. The substrate was kept 5 cm away from the source normal to the stream of Ar. The synthesis was carried out at 1173 K for 2 h. Morphological analysis of the pristine sample was studied using a field emission scanning electron microscope (FESEM, SUPRA 55 Zeiss). The crystallographic studies were performed with the help of glancing incidence X-ray diffractometer (GIXRD; Bruker D8) using a Cu Kα radiation source (λ = 1.5406 Å) with a glancing angle (θ) of 0.5° in the θ−2θ mode. Received: August 22, 2016 Revised: November 2, 2016 Published: November 2, 2016 26539

DOI: 10.1021/acs.jpcc.6b08452 J. Phys. Chem. C 2016, 120, 26539−26543

Article

The Journal of Physical Chemistry C

Figure 1. (a) FESEM image of as-grown nanorods. Inset shows a high-resolution image of a typical nanorod. (b) GIXRD spectrum of as-grown sample indicating crystalline planes corresponding to phases present.

A micro-Raman spectrometer (inVia, Renishaw, UK), in the back scattering configuration, was used with Ar+ laser (514.5 nm) as excitation source, diffraction gratings of 1800 gr·mm−1 for monochromatization and a thermoelectric cooled charged coupled device (CCD) as detector to study the vibrational modes. Electrical measurements were carried out by two Au coated contact tips. The activation energy Ea was calculated from the slope of ln(R) vs (1/T) plot, using the formula R = R0 exp(−Ea/KBT) where KB is the Boltzmann constant and R0 is the resistance at temperature T = 0 K. Absorption spectra were recorded using an UV−vis absorption spectrometer (Avantes) in the range of 200 to 700 nm. The Tauc’s plots of the asgrown material were drawn using (αhν)1/n vs hν with n = 2 for indirect band gap semiconductor (absorption coefficient, α; Planck’s constant, h; frequency, ν). Temperature-dependent spectroscopic studies and electrical measurements were performed in the Linkam (THMS600) stage.

3. RESULTS AND DISCUSSION The typical field FESEM image (Figure 1a) of as-grown sample shows rod-like structure with an average diameter of 200−300 nm. The inset in Figure 1a shows high magnification image of a typical single nanorod. The phase of the as-grown material was analyzed by GIXRD studies. Figure 1b shows the GIXRD data with peaks corresponding to the (hkl) planes of (001) and (002), confirming pure V2O5 phase (ICCD 00−041−1426) with unit cell dimensions a = 11.51 Å, b = 3.56 Å, and c = 4.37 Å grown with (001) crystalline orientation.13 As we have used Au as catalyst for the nanostructure growth, the GIXRD spectrum shows peaks corresponding to (111) and (200) planes for Au (ICCD 00−004−0784) also. Group theoretical analysis predicts 21 Raman active modes for V2O5 at Γ point, 7Ag + 7B2g + 3B1g + 4B3g.19 However, we observed 11 Raman modes for as-grown nanorods (Figure 2), which match with the reported data for V2O5.19,20 The Raman peaks at 102 (Ag), 144 (either B1g or B3g; B1g/ B3g), 195 (Ag/B2g), 283 (B1g/B3g), 301 (Ag), 403 (Ag), 483 (Ag), 523 (Ag), 701 (B1g/B3g), 850 (B1g), and 993 (Ag) cm−1 confirm the presence of pure V2O5 phase.19 Orthorhombic V2O5 is made of distorted VO5 pyramids sharing edges and corners 21 having space group Pmmn (D13 The 11 observed Raman 2h). peaks can be assigned as follows. The highest frequency peak at 993 cm−1 appears due to the stretching vibrational mode of V− OI bond along Z direction (for detailed structure refer to Supporting Information Figure S1). The peak at 850 cm−1 (inset of Figure 2), observed experimentally for the first time, is predicted to originate because of antiphase stretching mode of

Figure 2. Raman spectrum of the as grown V2O5 nanorods with excitation of 514.5 nm at room temperature. The inset shows a fitted peak at 850 cm−1 corresponding to B1g mode.

V−OII bonds corresponding to the displacement of OII atoms along X direction.19 The very weak intensity of the mode is due to pseudocentrosymmetric nature of V−OII−V bond.20 Displacement of OIII atoms in Y and X directions generates Raman modes at 701 cm−1 (V−OIII−V antiphase stretching mode) and 523 cm−1 (d4 stretching vibration), respectively. The V−OII−V bending deformation along Z direction (c axis) gives rise to Raman mode at 483 cm−1. Modes at 403 and 283 cm−1 can be attributed to oscillation of OI atoms along X and Y axes, respectively. However, displacement of OII atoms along Z axis gives rise to Raman peak at 301 cm−1. The low frequency modes at 195, 144, and 102 cm−1 correspond to the X, Y, and Z displacements of the whole chain involving shear and rotations of the ladder-like V−OIII bonds.20,22 The high intensity of 144 cm−1 peak indicates the long-range order of V−O layers in the XY plane.20 V2O5 is an indirect band gap semiconductor, with a gap value of about 2 eV.23,24 Presence of two localized narrow split-off bands with a gap of ∼0.7 eV at the bottom of conduction band is considered as the most interesting feature of its electronic band structure.24 The upper split-off band is separated from the main conduction band by an additional gap of 0.35 to 0.5 eV.23−25 However, V2O5 shows metallic behavior above the transition temperature. The semi-log plot of resistance (R) vs T−1 shows (Figure 3) that resistance decreases exponentially up to 450 K with 26540

DOI: 10.1021/acs.jpcc.6b08452 J. Phys. Chem. C 2016, 120, 26539−26543

Article

The Journal of Physical Chemistry C

metallic phase above the transition temperature.5 However, the role of specific O (Supporting Information Figure S1) is still not clear in producing the metallic phase. A temperature-dependent Raman spectroscopic study (Figure 4a) was conducted to address the role of specific O in producing the metallic phase. In temperature-dependent Raman study, the modes at 483 and 850 cm−1 are observed to disappear completely above the transition temperature of 530 K and reappear again at the same temperature while cooling down. Moreover, a softening for all Raman modes was recorded with the increase in temperature except for the mode frequencies at 283, 403, and 993 cm−1. Temperature dependence (increasing) of frequencies for all the observed Raman modes is shown in Figure 4b. The peak positions of the Raman modes, except for the three abovementioned modes, are red-shifted by an amount of 7 to 13 cm−1 in the temperature range from 300 to 650 K. The intensity of the peak centered at 993 cm−1 is observed to decrease rapidly with the increase in temperature and regain almost its original intensity after cooling back to room temperature. The intensity ratio of the highest intense 144 cm−1 (B1g/B3g) mode to 993 cm−1 (A1g) mode with increasing temperature is shown in Figure 4c. The intensity ratio (I_(B1g/ B3g)/I_A1g) increases rapidly above the temperature 450 K indicating a significant decrease in the intensity of A1g mode centered at 993 cm−1 as compared to that of B1g/B3g mode of 144 cm−1 around the transition temperature of 530 K. The drastic fall in intensity of the A1g mode, which is responsible for the vibration of vanadyl OI atoms along c-axis alone, signifies the possible loss of OI atoms from the structure around the transition temperature. It may also be noted that the B1g/B3g mode frequency at 144 cm−1 is independent of the motion of OI, so our inference about the role of OI influencing the intensity of A1g mode at 993 cm−1 is mutually exclusive. Moreover, it is reported that the vanadyl OI is more prone to reduction, as the vacancy formation energy is lower for OI atoms than the other two coordinated oxygen atoms (OII and OIII) in V2O5(001) oriented surface.28,29 The modes at 483 and 850 cm−1, arising due to V−OII−V bending and stretching vibrations, respectively, disappeared above the transition temperature. It may be due to the relaxation of V2O5 structure

Figure 3. Change in the resistance with temperature in an ensemble of V2O5 nanorods.

increasing temperature, indicating a semiconducting behavior leading to an activation energy of 0.29 ± 0.01 eV, which is slightly higher than the previously reported value (0.26 eV) for single crystalline V2O5, measured in the temperature range of 200−270 K.26 The most possible reason for this low value of activation energy is due to the transition of electrons from localized split-off bands to main conduction band. In the temperature range of 500−550 K, the slope of the plot is increased with an activation energy of 0.4 ± 0.01 eV, which indicates the downward shift of split-off bands with increasing temperature. Above 550 K, it starts decreasing rapidly disobeying the semiconducting nature, and the plot shows metallic behavior of increasing resistance with increase in the temperature above 650 K. As discussed earlier, the cause of the metallic behavior is still under debate.5,6,15−17 The proposed metallic phase of metastable γ′-V2O5 in the structural phase transition model17 is reported to convert to a stable semiconducting α-V2O5 phase above 613 K.27 In the present study, however, the temperature-dependent electrical measurement shows (Figure 3) that the metallic character of the grown nanorods sustains above 650 K, which contradicts the formation of γ′-V2O5. Hence, the reduction of V2O5 though O vacancy with no structural change is likely in producing the

Figure 4. (a) Raman spectra of V2O5 nanorods with increasing (denoted by solid arrow) and decreasing (denoted by dashed arrow) temperature in the range of 300 to 650 K (b) Change in vibrational frequency with temperature for each Raman mode. (c) Temperature dependence of the intensity ratio of the highest intense peak at 144 cm−1 (I_(B1g/B3g)) with the peak at 993 cm−1 (I_A1g). 26541

DOI: 10.1021/acs.jpcc.6b08452 J. Phys. Chem. C 2016, 120, 26539−26543

Article

The Journal of Physical Chemistry C

partially filled V 3d states in the conduction band,34 leading to the increase in the number of carriers in the conduction band. The increased number of carriers in the conduction band may be responsible for the decrease in resistance above the transition temperature and the observed metallic behavior. Thus, the decrease in band gap with increasing temperature supports our assumption of vanadyl OI vacancy from the V2O5 structure above the transition temperature.

initiated with the formation of vanadyl OI vacancy (schematic in the Supporting Information Figure S2). If one of the vanadyl oxygen atoms are removed from the surface, the V atom in its near vicinity projects inward for relaxation and the next right vanadyl oxygen relaxes upward to make a stiffer interlayer bond with increased bond length (1.78 Å). Moreover, the V−OII−V bond angle is also reported to increase to 178° leading to almost a linear bond.28 So, the disappearance of the modes at 483 and 850 cm−1 is in quite good agreement with the relaxation conditions. The absence of phonon softening with temperature for the Raman modes at 283, 403, and 993 cm−1, which originates due to the Y, X, and Z vibration of OI atoms, respectively, may also be attributed to the structural relaxation as the V−OI bonds become stiffer between the layers after the relaxation. The reversibility of the Raman modes with temperature can be explained by the excellent catalytic behavior of V2O5. Structural phase transition to γ′-V2O5 is further ruled out with the absence of Raman mode at 602 cm−1,30 in the studied temperature range of 300−650 K. To understand the origin of metallicity in V2O5, temperaturedependent UV−vis absorption of the as-grown V2O5 nanorods was studied. V2O5 is a semiconductor with an indirect band gap of ∼2 eV corresponding to a transition from R to Γ point in the first Brillouin zone.23,24 Two split-off bands with narrow bandwidth (0.45 to 0.75 eV) below the conduction band at Γ point are also reported.24,25 Vanadyl OI plays an important role in creating these split-off conduction bands.31,32 The Tauc’s plots of the as-grown material, using (αhν)1/2 vs hν for indirect band gap semiconductor (absorption coefficient, α; Planck’s constant, h; frequency, ν), at different temperatures ranging from 300 to 650 K are shown in Figure 5.

4. CONCLUSION In conclusion, orthorhombic V2O5(001) nanorods were synthesized by vapor transport method. Temperature-dependent electrical properties showed a transition of semiconducting to metallic behavior at temperature of 550 K. Phonon softening behavior in the temperature-dependent Raman spectra indicated loss of vanadyl oxygen (OI) as the most possible reason for the observation of the metallic V2O5 phase above the transition temperature. Reduction of the band gap with increasing temperature, as observed in the Tauc’s plot and thermal activation energy calculations, implies the downward movement of split-off bands from the conduction band. The downward shift of split-off bands with increase in temperature is due to breakdown of pdπ bond between OI and nearest V atom, inspired by the formation of vanadyl OI vacancy. The breakdown of pdπ bonds helps in accumulating electrons toward neighboring V atom to occupy the partially filled V 3d bands, leading to the increase in the number of carriers in conduction band, which is finally made responsible for the decrease in the resistance and the observed metallic behavior, for the first time.



ASSOCIATED CONTENT

S Supporting Information *

The Supporting Information is available free of charge on the ACS Publications website at DOI: 10.1021/acs.jpcc.6b08452. Brief description of the structure of V2O5 unit cell with schematic diagram (PDF)



AUTHOR INFORMATION

Corresponding Authors

*E-mail: [email protected]. Tel: +91 44 27480500, ext. 21512. *E-mail: [email protected]. Tel: +91 44 27480500, ext. 22513. Figure 5. Tauc’s plots of indirect band gap V2O5 nanorods using UV− visible spectra at different temperatures. The slopes are drawn to determine the band gap value, as inscribed in the insets for the plots at different temperatures.

Notes

The authors declare no competing financial interest.



ACKNOWLEDGMENTS R.B. thanks DAE, India for financial support. We also acknowledge D. N. Sunitha, S. R. Polaki, and A. Pasta of SND, IGCAR for their help in GIXRD, FESEM, and electrical studies, respectively.

An indirect band gap of 2.14 eV, which matches with the previously reported value of 2.1 eV,33 was recorded at 300 K. The band gap decreases with increase in temperature and is measured to attain a value of 2.07 eV at 650 K. The decrease in band gap by an amount of 70 meV indicates downward shift of the split-off bands with increase in temperature, as also inferred from the thermal activation energy analysis (Figure 3). Inspired by the vanadyl OI vacancy, the split-off conduction bands are reported to approach deeper down from the conduction band at Γ point due to the breakdown of pdπ bond between OI and nearest V atom.14,31,32 Reduction of an oxygen atom donates two electrons back to the structure. The breakdown of pdπ bond between OI and nearest V atom results in delocalization of electrons toward neighboring V cation by occupying the



REFERENCES

(1) Poizot, P.; Laruelle, S.; Grugeon, S.; Dupont, L.; Tarascon, J.-M. Nano-Sized Transition Metal Oxides as Negative-Electrode Materials for Lithium-Ion Batteries. Nature 2000, 407, 496−499. (2) Rao, C.N. R. Transition Metal Oxides. Annu. Rev. Phys. Chem. 1989, 40, 291−326. (3) Pergament, A.; Stefanovich, G.; Andreev, V. Comment on “Metal-Insulator Transition without Structural Phase Transition in V2O5 Film” [Appl. Phys. Lett. 98, 131907 (2011)]. Appl. Phys. Lett. 2013, 102, 176101. 26542

DOI: 10.1021/acs.jpcc.6b08452 J. Phys. Chem. C 2016, 120, 26539−26543

Article

The Journal of Physical Chemistry C

(27) Cocciantelli, J. M.; Gravereau, P.; Doumerc, J. P.; Pouchard, M.; Hagenmuller, P. On the Preparation and Characterization of a New Polymorph of V2O5. J. Solid State Chem. 1991, 93, 497−502. (28) Ganduglia-Pirovano, M.; Sauer, J. Stability of Reduced V2O5 (001) Surfaces. Phys. Rev. B: Condens. Matter Mater. Phys. 2004, 70, 045422−13. (29) Sauer, J.; Dobler, J. Structure and Reactivity of V2O5: Bulk Solid, Nanosized Clusters, Species Supported on Silica and Alumina, Cluster Cations and Anions. Dalton Trans. 2004, 3116−3121. (30) Baddour-Hadjean, R.; Smirnov, M. B.; Kazimirov, V. Y.; Smirnov, K. S.; Pereira-Ramos, J.-P. The Raman Spectrum of the Γ′V2O5 Polymorph: A Combined Experimental and DFT Study. J. Raman Spectrosc. 2015, 46, 406−412. (31) Lambrecht, W.; Djafari-Rouhani, B.; Vennik, J. On the Origin of the Split-Off Conduction Bands in V2O5. J. Phys. C: Solid State Phys. 1981, 14, 4785−4795. (32) Lambrecht, W.; Djafari-Rouhani, B.; Vennik, J. Theoretical Study of the Vanadyl-Oxygen Vacancy in V2O5: Tight-Binding Green Function Calculation, Optical Properties and Neutral Vacancy Ground-State Splitting. J. Phys. C: Solid State Phys. 1986, 19, 369−388. (33) Khan, G. A.; Hogarth, C. A. Electron Spin Resonance Studies of Evaporated V2O5 and Co-Evaporated V2O5/B2O3 Thin Films. J. Mater. Sci. 1991, 26, 2707−2710. (34) Wu, Q.-H.; Thissen, A.; Jaegermann, W.; Liu, M. Photoelectron Spectroscopy Study of Oxygen Vacancy on Vanadium Oxides Surface. Appl. Surf. Sci. 2004, 236, 473−478.

(4) Nadkarni, G. S.; Shirodkar, V. S. Experiment and Theory for Switching in Al/V2O5/Al Devices. Thin Solid Films 1983, 105, 115− 129. (5) Kang, M.; Kim, I.; Kim, S. W.; Ryu, J.-W.; Park, H. Y. MetalInsulator Transition without Structural Phase Transition in V2O5 Film. Appl. Phys. Lett. 2011, 98, 131907−3. (6) Blum, R. − P.; Niehus, H.; Hucho, C.; Fortrie, R.; GandugliaPirovano, M. V.; Sauer, J.; Shaikhutdinov, S.; Freund, H.-J. Surface Metal-Insulator Transition on a Vanadium Pentoxide (001) Single Crystal. Phys. Rev. Lett. 2007, 9, 226103−4. (7) Raible, I.; Burghard, M.; Schlecht, U.; Yasuda, A.; Vossmeyer, T. V2O5 Nanofibres: Novel Gas Sensors with Extremely High Sensitivity and Selectivity to Amines. Sens. Actuators, B 2005, 106, 730−735. (8) Dhayal Raj, A.; Pazhanivel, T.; Kumar, P. S.; Mangalaraj, D.; Nataraj, D.; Ponpandian, N. Self Assembled V2O5 Nanorods for Gas Sensors. Curr. Appl. Phys. 2010, 10, 531−537. (9) Nishio, S.; Kakihana, M. Evidence for Visible Light Photochromism of V2O5. Chem. Mater. 2002, 14, 3730−3733. (10) Zuli, L.; Guojia, F.; Youqing, W.; Yandong, B. Laser-Induced Colouration of V2O5. J. Phys. D: Appl. Phys. 2000, 33, 2327−2332. (11) Krishnakumar, S.; Menon, C. S. Optical and Electrical Properties of Vanadium Pentoxide Thin Films. phys. stat. sol. (a) 1996, 153, 439−444. (12) Xie, S.; Iglesia, E.; Bell, A. T. Effects of Temperature on the Raman Spectra and Dispersed Oxides. J. Phys. Chem. B 2001, 105, 5144−5152. (13) Enjalbert, R.; Galy, J. A Refinement of the Structure of V2O5. Acta Crystallogr., Sect. C: Cryst. Struct. Commun. 1986, 42, 1467−1469. (14) Lambrecht, W.; Djafari-Rouhani, B.; Vennik, J. Electronic Structure of Bulk and Surface Vanadyl Oxygen Vacancies in the Layer Compound V2O5. Surf. Sci. 1983, 126, 558−564. (15) Eon, J. G.; Olier, R.; Volta, J. C. Oxidative Dehydrogenation of Propane on γ-Al2O3 Supported Vanadium Oxides. J. Catal. 1994, 145, 318−326. (16) Ramirez, R.; Casal, B.; Utrera, L.; Ruiz-Hitzky, E. Oxygen Reactivity in Vanadium Pentoxide: Electronic Structure and Infrared Spectroscopy Studies. J. Phys. Chem. 1990, 94, 8960−8965. (17) Rubin Aita, C. Additional Comment on “Metal-Insulator Transition without Structural Phase Transition in V2O5 Film” [Appl. Phys. Lett. 98, 131907 (2011)]. Appl. Phys. Lett. 2014, 104, 176101−2. (18) Wilhelmi, K. A.; Walterson, K. On the Crystal Structure of a New Vanadium Oxide, V4O9. Acta Chem. Scand. 1970, 24, 3409−3411. (19) Abello, L.; Husson, E.; Repelin, Y.; Lucazeau, G. Vibrational Spectra and Valence Force Field of Crystalline V2O5. Spectrochim. Acta, Part A: Mol. Spectrosc. 1983, 39, 641−651. (20) Baddour-Hadjean, R.; Pereira-Ramos, J. P.; Navone, C.; Smirnov, M. Raman Microspectrometry Study of Electrochemical Lithium Intercalation into Sputtered Crystalline V2O5 Thin Films. Chem. Mater. 2008, 20, 1916−1923. (21) Bachmann, H. G.; Ahmed, F. R.; Barnes, W. H. The Crystal Structure of Vanadium Pentoxide. Z. Kristallogr. 1961, 115, 110−131. (22) Clauws, P.; Broeckx, J.; Vennik, J. Lattice Vibrations of V2O5. Calculation of Normal Vibrations in a Urey-Bradley Force Field. Phys. Status Solidi B 1985, 131, 459−473. (23) Chakrabarti, A.; Hermann, K.; Druzinic, R.; Witko, M.; Wagner, F.; Petersen, M. Geometric and Electronic Structure of Vanadium Pentoxide: A Density Functional Bulk and Surface Study. Phys. Rev. B: Condens. Matter Mater. Phys. 1999, 59, 10583−10590. (24) Parker, J. C.; Lam, D. J.; Xu, Y.-N.; Ching, W. Y. Optical properties of vanadium pentoxide determined from ellipsometry and band-structure calculations. Phys. Rev. B: Condens. Matter Mater. Phys. 1990, 42, 5289−5293. (25) Eyert, V.; Höck, K.-H. Electronic Structure of V2O5: Role of Octahedral Deformations. Phys. Rev. B: Condens. Matter Mater. Phys. 1998, 57, 12727−12737. (26) Karakotsou, Ch.; Kalomiros, J. A.; Hanias, M. P.; Anagnostopoulos, A. N.; Spyridelis, J. Nonlinear Electrical Conductivity of V2O5 Single Crystals. Phys. Rev. B: Condens. Matter Mater. Phys. 1992, 45, 11627−11631. 26543

DOI: 10.1021/acs.jpcc.6b08452 J. Phys. Chem. C 2016, 120, 26539−26543