SiO2 Nanocomposites to β-SiC

Nov 17, 2017 - Moreover, the conventional carbothermal reduction is not a pseudomorphic transformation process.11 The generation of gaseous silicon mo...
0 downloads 9 Views 1MB Size
Subscriber access provided by READING UNIV

Article

Low-temperature transformation of C/SiO2 nanocomposites to #-SiC with high surface area Xiong-fei Zhang, Zhouyuan Chen, Yi Feng, Jianhao Qiu, and Jianfeng Yao ACS Sustainable Chem. Eng., Just Accepted Manuscript • DOI: 10.1021/ acssuschemeng.7b03375 • Publication Date (Web): 17 Nov 2017 Downloaded from http://pubs.acs.org on November 19, 2017

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

ACS Sustainable Chemistry & Engineering is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 20

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

Low-temperature transformation of C/SiO2 nanocomposites to β-SiC with high surface area

Xiong-Fei Zhanga, Zhouyuan Chena, Yi Fenga, Jianhao Qiua, Jianfeng Yao a,b,* a

College of Chemical Engineering, Nanjing Forestry University, 159 Longpan Road,

Nanjing, Jiangsu 210037, China. Email: [email protected] b

Jiangsu Key Lab for the Chemistry & Utilization of Agricultural and Forest

Biomass, Jiangsu Key Lab of Biomass-based Green Fuels and Chemicals, Nanjing Forestry University, 159 Longpan Road, Nanjing, 210037 China

ABSTRACT Mesoporous

silicon

carbide

(SiC)

nanostructures

were

synthesized

by

magnesiothermic reduction of carbon-silica (C/SiO2) nanocomposites at a low temperature of 700 °C by using furfuryl alcohol as the carbon source. The phase, morphology and structure of the samples were characterized by a combination of Xray diffraction, scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectra, X-ray photoelectron spectroscopy, thermogravimetric analysis and N2 adsorption. The starting C/SiO2 composites exhibited an interpenetrating network and the resulting SiC preserved the mesoporous properties of the original templates. The SiC products were of β-SiC phase and showed a high surface area of 786 m2/g. The reaction mechanism and role of intermediate species (Mg2Si) were explored in detail. Furthermore, the resulting β-SiC exhibits remarkable electromagnetic wave absorption performance with a minimum reflection loss of 17.2 dB and reflection loss bandwidth < -10 dB of 3.7 GHz. 1

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

KEYWORDS: Magnesiothermic reduction; β-SiC; high surface area; microwave adsorption

INTRODUCTION Silicon carbide (SiC) functional nanomaterials have numerous potential applications in semiconductors, catalysts, functional ceramics, high-frequency electronics and wave-absorbing devices due to outstanding thermal stabilities, large avalanche breakdown field, excellent mechanical properties, high electron saturation velocity, and superior chemical inertness.1-3 To date, overwhelming breakthroughs in growth of SiC nanomaterials have been achieved and numerous techniques were developed to fabricate nanostructured SiC, including laser ablation, chemical vapor deposition, autogenic pressure reactions, pyrolysis of polymeric precursors, nanocasting, arc-discharge and carbothermal reduction.1,

4,5

Problems appeared in

some of the processes, such as the use of toxic precursors, complicated equipments, and heavy agglomeration of the products. In our previous work, we have reported that SiC nanoparticles and nanofibers can be produced via carbothermal reduction of C/SiO2 nanocomposites.6-8 However, the carbothermal reduction process involves complicated equipments and always performs at very high temperature (>1300 °C).9,10 Moreover, the conventional carbothermal reduction is not a pseudomorphic transformation process.11 The generation of gaseous silicon monoxide (SiO) intermediate destroys the starting network and causes particle aggregation.12 Problems related to control of grain growth and sintering make it difficult to produce SiC with high surface area and regular morphological forms. However, in most applications of SiC, surface area is thought to be an important consideration. It is therefore desirable to develop new methods to convert C/SiO2 composite to the corresponding SiC 2

ACS Paragon Plus Environment

Page 2 of 20

Page 3 of 20

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

materials without losing the pristine nanostructure and morphology of the precursors.13-15 To this end, increasing attention has been paid to alternative magnesiothermic reduction.16-18 For example, Shi et al. developed a template approach for directly converting

C/SiO2

composites

to

hierarchical

SiC

nanomaterials

via

a

magnesiothermic reaction at a relatively low temperature.14 They adopted Pluronic F127 block copolymer and polystyrene spheres as dual templates to prepare the precursor. After the magnesiothermic reduction, the structure of the SiC products was consistent with the precursor. A similar approach was taken to synthesize SiC nanomaterials by Mojarad et al. but using mesoporous carbon or zeolites (SBA15/KIT-6) as hard templates.10 Herein, we report the fabrication and characterization of SiC with high surface area and well-defined porosity from interpenetrating C/SiO2 precursors.19 Furfuryl alcohol (FA) was chosen as the carbon source, and it is one of the most important furanic derivatives that have been industrially converted from renewable saccharidic biomasses.20,21 Synthesis of SiC nanomaterials using bio-based resources has drawn increasing attention as it is an environmental friendly and costeffective route.21 The prepared SiC nanoparticles were of β-SiC phase with sizes of 40-100 nm. The generation of SiO gas was avoided and thus the original morphology and structure regularity were preserved. The reaction mechanism was discussed in detail. In addition, the electromagnetic (EM) wave absorption performance of the SiC nanoparticles was investigated and a remarkable performance was observed. EXPERIMENTAL Materials. P123 (EO20-PO70-EO20) was purchased from Adamas, China. Tetraethoxysilane (TEOS, 99%) was obtained from Shanghai Lingfeng Chemical, 3

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

China. Anhydrous ethanol and FA (99%) were purchased from Sinopharm Chemical, China. All chemicals were used as received without further purification. Preparation of C/SiO2 composites. C/SiO2 nanocomposites were fabricated according to our previous method with minor changes.8, 22 In a typical synthesis, 5.0 g of H2O, 3.3 g of ethanol and 0.5 g of HCl (1 M) were mixed in a capped polypropylene bottle. 4.1 g of P123 was then added to this solution under continuous agitation. Following that, 10.0 g of TEOS and 5.0 of FA were added slowly under vigorously agitation. The resulting mixtures were stirred at room temperature for 3 h and subsequently aged for four days and drying at 80 °C for another three days. The acquired black monoliths (silica-P123-FA) were ground into powders and carbonized in N2 at the heating rate of 1 °C min-1, and kept at 550 °C for 5 h to form C/SiO2 composites. As comparison, the silica-P123-FA was also calcined under air using the same heating program to produce SiO2. Preparation of SiC nanoparticles. The obtained C/SiO2 composites were mixed and ground with magnesium powder (C/SiO2 : Mg weight ratios of 1:1, 1:2, 1:3 and 1:4), and then transferred into a sealed tube furnace. Before heating, the furnace was vacuumed to evacuate air for 0.5 h. Afterwards, the composites were heated under an argon atmosphere with a heating rate of 5 °C min-1 to 700 °C. The samples were kept at the setting temperature for 6 h and then cooled down. Finally, the SiC in high purity was acquired after etching the mixture with HCl (2 M) for 2 h to remove residue compounds and subsequently subject to carbon burnoff at 550 °C for 5 h. The acquired samples were denominated as SiC-1, SiC-2, SiC-3, SiC-4 according to the Mg addition.

4

ACS Paragon Plus Environment

Page 4 of 20

Page 5 of 20

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

Characterization. The phase structure of the samples was recorded on an X-ray diffraction (XRD) using Rigaku MiniFlex II with Cu Kr radiation. Nitrogen adsorption-desorption experiments were performed at 77 K with a Micromeritics ASAP 2020. Fourier transform infrared spectra (FT-IR) were conducted by a FTIR spectrophotometer (Thermo Electron Nicolet-360, USA) using the KBr wafer technique. The morphology of the samples was observed by scanning electron microscopy (SEM) utilizing a JSM-7600F (JEOL Ltd., Japan) with an operating voltage of 30 kV. Thermo-gravimetric analysis (TGA) (Perkin-Elmer, Pyris 1 thermogravimetric analyzer) was conducted at a heating rate of 10 °C min-1 to 1000 °C. Xray photoelectron spectroscopy (XPS, AXIS UltraDLD, Japan) was employed to determine surface electronic states of the samples. All the binding energies were referenced to the C1s peak of the surface adventitious carbon. Microstructural observations were performed using a transmission electron microscope (TEM, Model 2100F, JEOL Ltd., Tokyo, Japan) operating at 200 kV, and elemental mapping images were obtained by using Energy-Dispersive X-ray Spectroscopy (EDX) attached to the JEOL 2100F microscope. Wave absorption performance. For EM wave absorption measurement, the assynthesized samples were dispersed into paraffin (as substrate) with a weight ratio of 5 : 5 to fabricate the corresponding composite. The composite were then molded to a ring-shape with an inner diameter of 3 mm and an outer diameter of 7 mm. The EM parameters were determined by using an E5071C series vector network analyzer (Agilent, USA) at EM frequencies of 2-18 GHz. The analyzer was in operating mode for at least 30 min before calibration and subsequent data collection. All measurements were carried out in triplicate.

5

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

RESULTS AND DISCUSSION Characterization of the materials. To confirm the crystal structure of samples, XRD pattern of the C/SiO2 composite (Figure 1a) shows a broad hump in the range of 2126°, which corresponds to the amorphous silica and carbon. The XRD pattern of SiC without purification (Figure 1b) exhibits several intense diffraction peaks. Some of them are assigned to typical (111), (200) and (220) peaks of cubic MgO phase (JCPDS No. 45-0946), representing the existence of MgO nanocrystals.23,24 The peaks centered at 44.6° and 78.1° are attributed to residual Mg powder. In addition, the weak peak located at 24.2° and 28.1° are indexed to Mg2Si, indicating the presence of a trace amount of Mg2Si.12 It is worthy noted that the diffraction peaks of Si were not observed, which can be ascribed to the excess carbon used. After acid etching and carbon burn off, the sharp peaks at 2θ = 35.6, 41.4, 60.0, 71.7, and 75.5° are attributed to the (111), (200), (220), (311), and (222) planes of βSiC (JCPDS No. 29-1129), respectively.25,26 The slight peak at 33.6° marked with S.F. is ascribed to the stacking faults in the crystalline β-SiC structure. XRD patterns of SiC products synthesized with different Mg addition show the same peaks but with different intensity, which indicates that amorphous C/SiO2 precursor was transformed into SiC via low-temperature magnesiothermic reduction. No evidence of phases associated with other impurities is observed, implying that Mg2Si and MgO were both completely removed by HCl treatment. It should be highlighted that HF or HNO3 is not used in purification process, as there is no residual SiO2 in the resulting products. The average crystallite size of the β-SiC was calculated to be 7.9 nm by Scherrer analysis. 6

ACS Paragon Plus Environment

Page 6 of 20

Page 7 of 20

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

Figure 1. XRD patterns of the C/SiO2 composite (a), the products before purification (b), SiC-1 (c), SiC-2 (d), SiC-3 (e) and SiC-4 (f).

The microstructure of the SiC products were further characterized by the N2 adsorption-desorption analysis. As illustrated in Figure 2, all samples present a representative type IV isotherm with a hysteresis loop at P/Po of 0.4-0.8, indicating the presence of mesoporous structures. The samples possess higher N2 adsorption capacity than that of most of other SiC nanomaterials reported previously.6, 8, 14 The BET surface area of the mesoporous SiC initially increases from 704 to 786 m2/g when the weight ratio changes from 1:1 (SiC-1) to 1:2 (SiC-2), and then decreases to 586 m2/g when the weight ratio becomes 1:3 (SiC-3). The decrease of the surface area might be attributed to the abrupt and massive heat release caused by addition of excess Mg powder. The heat generated in contact zone between Mg and C/SiO2 composite ruins the pristine porous structure to some extent and leads to rapid growth of SiC crystals. Further increasing the Mg addition, the specific surface area of SiC-4 decreases substantially to 170 m2/g, confirming the sintering and aggregation of SiC 7

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

nanoparticles. N2 adsorption isotherm of C/SiO2 composites also display Type IV curves (mesoporous structures) and have a BET specific surface area of 1022 m2/g. As compared with the interpenetrating C/SiO2 precursor, the obtained SiC products inherit the sufficient mesoporosity and preserve the high surface area. The relatively weaker order of mesopores in SiC products is due to the slight collapse of part framework during the synthesis process. It is concluded that the mesoporous C/SiO2 nanocomposite serves as matrix template and Mg powder plays a crucial role in determining the surface area.

Figure 2. N2 adsorption-desorption isotherms of SiC products.

Figure 3 illustrates the FT-IR spectra of the as-synthesized C/SiO2 precursor and SiC products. All samples show an obvious broad peak at around 3450 cm-1, which is associated with the O-H stretching vibration mode of the adsorbed water. And the absorption bands centered at 1645 cm-1 is caused by the O-H bending vibration mode. For C/SiO2 nanocomposite, the strong bands at 1080 and 460 cm-1 are ascribed to the asymmetric Si-O-Si stretching vibration. Upon reduction treatment and purification process, the peak belongs to the mesoporous silica is significantly weakened. But a 8

ACS Paragon Plus Environment

Page 8 of 20

Page 9 of 20

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

pronounced band centered at 830 cm-1 corresponding to vibration of Si-C bond appears.7 Consistent with XRD results, the FT-IR spectra verified the successful formation of SiC from the initial C/SiO2 composites.27

Figure 3. FT-IR spectra of C/SiO2 composite and SiC products.

Thermogravimetric (TG) analysis was conducted and TG curve of SiC-2 is shown in Figure 4a. The measurement result implies that the as-prepared SiC has oxidation resistance and thermal stability. There is no drastic weight gain or loss below 700 °C. The slight weight increase above 700 °C could be attributed to the partial oxidation of nanocrystalline SiC under oxidative atmosphere, which is in line with prior reports.10, 28

Besides, the molar ratio of C: SiO2 in the precursor C/SiO2 composite was

calculated to be 3.4:1 by burn off the carbon in air at 550 °C for 5 h. As illustrated in Figure 4b, the morphology of SiC-2 shows uniform particle size of about 40-100 nm. Although

slight aggregation

of

nanoparticles

was observed,

the

original

nanostructures of precursors are fairly well retained after magnesiothermic reduction. By contrast, in the carbothermic reduction, the SiC nanoparticles subject to severe 9

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

agglomerate because of the high reaction temperature and intense exothermic process.1 There is no detectable structural shrinkage occurred in magnesiothermic reduction. Three reasons were summarized :1) interpenetrating C and SiO2 in the composite contributes to a rigid framework, which acts as stable support or a barrier against aggregation; 2) Structure and porosity preservation is favored by a low temperature; and 3) there is no evidence of SiO gas produced during the reaction, thus the SiC products exhibit a very low sinterability.12

Figure 4. TG curve (a) and SEM image (b) of the SiC-2 sample. The prepared SiC samples were grey green in color, which was consistent with the color of SiC obtained in industries using coke as the carbon source. A representative TEM image of SiC-2 is shown in Figure 5a, which evidently appears that the product is mainly composed of nanoparticles with sizes of 40-100 nm.29 As illustrated in Figure 5b and c, elemental mapping images of SiC-2 nanoparticles reveal the presence of Si and C. In addition, the weak O element signal in the mapping image (not shown) is attributed to the inevitable oxidation on the surface of SiC nanoparticles.30

10

ACS Paragon Plus Environment

Page 10 of 20

Page 11 of 20

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

Figure 5. TEM image of SiC-2 (a) elemental mapping images of C (b) and Si (c). XPS analysis was performed to study the chemical state of SiC nanoparticles and the results were presented in Figure 6. The XPS spectrum of Si 2p (Figure 6b) region shows two peaks. The peak located at 100.4 eV can be assigned to Si in SiC form, while the weak peak centered at 102.0 eV corresponds to Si in SiO2. This is in agreement with XRD and FT-IR results. As illustrated in Figure 6c, the C 1s peak can be de-convoluted into two sub-peaks at 282.7 and 286.3 eV associated with SiC particles and trace residual carbon, respectively.

Figure 6. XPS survey spectrum of the SiC-2 (a), high-resolution scans of Si 2p (b) and C 1s (c) XPS spectra with the fitted results. Reaction mechanism. With respect to the specific reaction process, several mechanisms have been proposed and the detailed mechanism is still underway. Shi et 11

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 12 of 20

al. stated that SiO2 is reduced to Si and then Si reacts with C to produce SiC.14 While other researchers thought that Mg reacts with C initially to generate Mg2C3 or MgC2 intermediate and subsequently MgC2 interacts with SiO2 to form SiC.11 Some other studies suggested that Mg2Si is the possible intermediate species.12 However, available studies mostly lack insights into the basic thermodynamics of reactions.31,32 Thermodynamics calculations have proven to be a useful tool for explaining and understanding the reactions steps at the atomistic level.33 As shown in Figure 7, the Gibbs free energy changes (∆G) for reaction (5) is more negative in 700°C, demonstrating the thermodynamic possibility of formation of Mg2Si based on the theory.

Figure 7. The Gibbs free energy changes as a function of the temperature (calculated by Software HSC Chemistry 6.0).

Based on our experimental results, a two-step reaction mechanism is given as follows: SiO2 + Mg → Mg2Si + 2MgO 12

ACS Paragon Plus Environment

(1)

Page 13 of 20

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

Mg2Si + SiO2 + C → 2SiC + 2MgO

(2)

The overall reaction can be described as: SiO2 + 2Mg + C → SiC + 2MgO

(3)

As the reaction temperature was over the melting point of Mg (~650 oC), Mg2Si were formed at the Mg-SiO2 interface. This is supported by the XRD pattern of magnesiothermic reduction performed at a lower temperature of 650 °C (Figure 8), in which the peaks corresponding to Mg2Si were clearly observed.29 In addition, this process preserved the nanostructure of SiO2 templates by avoiding the formation of gaseous SiO that breaks down the initial structure.14

Figure 8. XRD patterns of the product before purification (650 °C).

The formation process of SiC was proposed in Figure 9, where the in situ-formed Mg2Si encounters C and subsequently converts to SiC. In our syntheses, the C/SiO2 composites were synthesized via infiltrating FA into the mesochannels of SiO2. Ethanol and HCl were used to slow down the cationic poly-condensation process of 13

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

FA for keeping pace with the hydrolysis of TEOS. Therefore, interpenetrating C/SiO2 composite makes it possible for the Mg2Si intermediate to directly react with nearby C species. The well-dispersed C species in the self-supporting C/SiO2 framework prevents the SiC products from aggregating and sintering further. The excess amount of C and its good contact with SiO2 facilitate SiC formation are crucial to maintain the integrity of the mesoporous structure. Using Mg not only reduces the reaction temperature but also allows preparation of SiC materials with a high mesoporosity. Mg powder acts as reagent in the first step and serves as catalyst in the second step. The amounts of Mg addition decide the violence of the reaction, and thus influencing the final morphology and structure of SiC products.

Figure 9. Schematic illustration of the reaction mechanism for SiC formation

Microwave absorption performance. As displayed in Figure 10, the sample (SiC-2 was tested as an example) shows considerable EM wave absorption with a minimum reflection loss of -17.2 dB and absorption bandwidth < -10 dB (over 90% microwave absorption) of 3.7 GHz (between 8.1 and 11.8 GHz). All of these values are superior to that in the literature, demonstrating that the prepared SiC materials have excellent electromagnetic wave absorbing performance.12,

30, 34,35

The resulting SiC products

preserved the mesoporous properties of the original templates. The excellent microwave absorption performance of SiC-2 is attributed to multi-dielectric 14

ACS Paragon Plus Environment

Page 14 of 20

Page 15 of 20

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

polarization arising from the high surface area and the mesoporous structures.36 This provides a high density of stacking faults and polarized centers, thus making the space charge polarization and relaxation process easier by trapping space charges.37

Figure 10. Frequency dependence of reflection loss of the SiC-2.

CONCLUSION In this study, mesoporous β-SiC with a high surface area of 786 m2/g has been prepared at a relative low temperature of 700 °C via the magnesiothermic reduction. This method provides greater control of the structural ordering and the products preserve the nanostructure and mesoporosity of the interpenetrating precursor. Moreover, the reaction mechanism was explored in detail and some new insights were delivered. We have provided conclusive evidence that SiO2 is first reduced to the intermediate product Mg2Si, and then SiC is formed from the metathesis of Mg2Si and C. The approach presented here is expected to be a general way for various nanostructured carbide materials at relatively low temperature by carefully designing structures of their precursors. Sample SiC-2 exhibits remarkable EM wave absorption 15

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

with a minimum reflection loss of -17.2 dB and reflection loss bandwidth < -10 dB of 3.7 GHz. This material has great potential in the application of high-temperature EM wave absorbers due to its high surface, good thermal stability, excellent chemical resistivity and low density.

ACKNOWLEDGMENTS The authors are grateful for the financial support of China Postdoctoral Science Foundation (2017M611824), Natural Science Key Project of the Jiangsu Higher Education Institutions (15KJA220001), Jiangsu Specially-Appointed Professor Program.

REFERENCES (1) Wu, R.; Zhou, K.; Yue, C. Y.; Wei, J.; Pan, Y. Recent progress in synthesis, properties and potential applications of SiC nanomaterials. Prog. Mater Sci. 2015, 72, 1-60. (2) Bao, Z.; Weatherspoon, M. R.; Shian, S.; Cai, Y.; Graham, P. D.; Allan, S. M.; Ahmad, G.; Dickerson, M. B.; Church, B. C.; Kang, Z.; Abernathy, H. W., III; Summers, C. J.; Liu, M.; Sandhage, K. H. Chemical reduction of three-dimensional silica micro-assemblies into microporous silicon replicas. Nature 2007, 446 (7132), 172-175. (3) Yang, Z. X.; Xia, Y. D.; Mokaya, R. High surface area silicon carbide whiskers and nanotubes nanocast using mesoporous silica. Chem. Mater. 2004, 16 (20), 3877-3884. (4) Li, T.; Xu, L.; Wang, L.; Yang, L.; Qjan, Y. Synthesis and characterization of 3C and 2HSiC nanocrystals starting from SiO2, C2H5OH and metallic Mg. J. Alloys Compd. 2009, 484 (1-2), 341-346. (5) He, Z.; Wang, L.; Gao, F.; Wei, G.; Zheng, J.; Cheng, X.; Tang, B.; Yang, W. Synthesis of n-type SiC nanowires with tailored doping levels. Crystengcomm 2013, 15 (13), 2354-2358.

16

ACS Paragon Plus Environment

Page 16 of 20

Page 17 of 20

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

(6) Wang, K.; Yao, J.; Wang, H.; Cheng, Y. B. Effect of seeding on formation of silicon carbide nanostructures from mesoporous silica-carbon nanocomposites. Nanotechnology 2008, 19 (17). (7) Yao, J.; Wang, H.; Zhang, X.; Zhu, W.; Wei, J.; Cheng, Y. B. Role of pores in the carbothermal reduction of carbon-silica nanocomposites into silicon carbide nanostructures. Journal of Physical Chemistry C 2007, 111 (2), 636-641. (8) Wang, K.; Wang, H.; Cheng, Y. B. Synthesis of nanostructured silicon carbide spheres from mesoporous C-SiO2 nanocomposites. Chem. Commun. 2010, 46 (2), 303-305. (9) Ju, Z.; Xu, L.; Pang, Q.; Xing, Z.; Ma, X.; Qian, Y. The synthesis of nanostructured SiC from waste plastics and silicon powder. Nanotechnology 2009, 20 (35). (10) Mojarad, B. S.; Nourbakhsh, A.; Kahrizsangi, R. E.; Masoud, M.; MacKenzie, K. J. D. Synthesis of nanostructured SiC by magnesiothermal reduction of silica from zeolite ZSM-5 and carbon: The effect of carbons from different sources. Ceram. Int. 2015, 41 (4), 5287-5293. (11) Dasog, M.; Smith, L. F.; Purkait, T. K.; Veinot, J. G. C. Low temperature synthesis of silicon carbide nanomaterials using a solid-state method. Chem. Commun. 2013, 49 (62), 7004-7006. (12) Su, J.; Gao, B.; Chen, Z.; Fu, J.; An, W.; Peng, X.; Zhang, X.; Wang, L.; Huo, K.; Chu, P. K. Large-Scale Synthesis and Mechanism of beta-SiC Nanoparticles from Rice Husks by Low-Temperature Magnesiothermic Reduction. Acs Sustainable Chem. Eng. 2016, 4 (12), 6600-6607. (13) Zhao, B.; Zhang, H.; Tao, H.; Tan, Z.; Jiao, Z.; Wu, M. Low temperature synthesis of mesoporous silicon carbide via magnesiothermic reduction. Mater. Lett. 2011, 65 (11), 15521555. (14) Shi, Y.; Zhang, F.; Hu, Y.-S.; Sun, X.; Zhang, Y.; Lee, H. I.; Chen, L.; Stucky, G. D. Low-Temperature

Pseudomorphic Transformation of

Ordered Hierarchical

Macro-

mesoporous SiO2/C Nanocomposite to SiC via Magnesiothermic Reduction. J. Am. Chem. Soc. 2010, 132 (16), 5552-5559. 17

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

(15) Liu, P.; Xie, S.; Peng, M.; Ni, L.; Tang, Y.; Chen, Y. Synthesis and characterization of hollow Si-SiC composite nanospheres from hollow SiO2/C nanospheres. J. Sol-Gel Sci. Technol. 2015, 73 (1), 270-277. (16) Chen, K.; Bao, Z.; Du, A.; Zhu, X.; Wu, G.; Shen, J.; Zhou, B. Synthesis of resorcinolformaldehyde/silica composite aerogels and their low-temperature conversion to mesoporous silicon carbide. Microporous Mesoporous Mater. 2012, 149 (1), 16-24. (17) Jiang, Z.; Ma, Y.; Zhou, Y.; Hu, S.; Han, C.; Pei, C. Facile fabrication of threedimensional mesoporous Si/SiC composites via one-step magnesiothermic reduction at relative low temperature. Mater. Res. Bull. 2013, 48 (10), 4139-4145. (18) Saeedifar, Z.; Nourbakhsh, A. A.; Saeedifar, M. Effect of acrylamide monomer concentration in low temperature magnesiothermic synthesis of mesoporous silicon carbide from MCM-48/PAAM nanocomposite precursor. Adv. Appl. Ceram. 2014, 113 (3), 167-172. (19) Li, Z.; Zhang, J.; Meng, A.; Guo, J. Large-area highly-oriented SiC nanowire arrays: Synthesis, Raman, and photoluminescence properties. J. Phys. Chem. B 2006, 110 (45), 22382-22386. (20) Wang, H.; Yao, J. Use of poly(furfuryl alcohol) in the fabrication of nanostructured carbons and nanocomposites. Ind. Eng. Chem. Res. 2006, 45 (19), 6393-6404. (21) Wang, T.; Sun, H.; Long, J.; Wang, Y. Z.; Schiraldi, D. Biobased Poly(furfuryl alcohol)/Clay Aerogel Composite Prepared by a Freeze-Drying Process. Acs Sustainable Chem. Eng. 2016, 4 (5), 2601-2605. (22) Yao, J. F.; Wang, H. T.; Chan, K. Y.; Zhang, L. X.; Xu, N. P. Incorporating organic polymer into silica walls: A novel strategy for synthesis of templated mesoporous silica with tunable pore structure. Microporous Mesoporous Mater. 2005, 82 (1-2), 183-189. (23) Pang, Q.; Xu, L.; Ju, Z.; Xing, Z.; Yang, L.; Hao, Q.; Qian, Y. 3C-SiC nanowires and micro-scaled polyhedra: Synthesis, characterization and properties. J. Alloys Compd. 2010, 501 (1), 60-66.

18

ACS Paragon Plus Environment

Page 18 of 20

Page 19 of 20

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

(24) Li, P.; Xu, L.; Qian, Y. Selective synthesis of 3C-SiC hollow nanospheres and nanowires. Cryst. Growth .Des. 2008, 8 (7), 2431-2436. (25) Zhu, H.-L.; Han, F.-D.; Lun, N.; Qi, Y.-X.; Bai, Y. J.; Bi, J. Q.; Meng, X. L.; Zhang, B.; Wang, Y.; Liu, J. R.; Fan, R. H. Rapid, Low-Temperature Synthesis of beta-SiC Nanowires from Si and Graphite. J. Am. Ceram. Soc. 2010, 93 (9), 2415-2418. (26) An, W.; Su, J.; Chen, Z.; Gao, B.; Zhang, X.; Peng, X.; Peng, S.; Fu, J.; Chu, P. K. LowTemperature Synthesis of Mesoporous SiC Hollow Spheres by Magnesiothermic Reduction. J. Am. Ceram. Soc. 2016, 99 (6), 1859-1861. (27) Henderson, E. J.; Veinot, J. G. C. From Phenylsiloxane Polymer Composition to SizeControlled Silicon Carbide Nanocrystals. J. Am. Chem. Soc. 2009, 131 (2), 809-815. (28) Hosseini, B.; Nourbakhsh, A. A.; MacKenzie, K. J. D. Magnesiothermal synthesis of nanostructured SIC from natural zeolite (clinoptilolite) and mesoporous carbon CMK-1. Ceram. Int. 2015, 41 (7), 8809-8813. (29) Rajarao, R.; Ferreira, R.; Sadi, S. H. F.; Khanna, R.; Sahajwalla, V. Synthesis of silicon carbide nanoparticles by using electronic waste as a carbon source. Mater. Lett. 2014, 120, 65-68. (30) Chen, J.; Liu, M.; Yang, T.; Zhai, F.; Hou, X.; Chou, K. C. Improved microwave absorption performance of modified SiC in the 2-18 GHz frequency range. Crystengcomm 2017, 19 (3), 519-527. (31) Han, X. D.; Zhang, Y. F.; Zheng, K.; Zhang, X. N.; Zhang, Z.; Hao, Y. J.; Guo, X. Y.; Yuan, J.; Wang, Z. L. Low-temperature in situ large strain plasticity of ceramic SiC nanowires and its atomic-scale mechanism. Nano Lett. 2007, 7 (2), 452-457. (32) Castelletto, S.; Johnson, B. C.; Zachreson, C.; Beke, D.; Balogh, I.; Ohshima, T.; Aharonovich, I.; Gali, A. Room Temperature Quantum Emission from Cubic Silicon Carbide Nanoparticles. Acs Nano 2014, 8 (8), 7938-7947.

19

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

(33) Ahn, J.; Kim, H. S.; Pyo, J.; Lee, J.-K.; Yoo, W. C. Variation in Crystalline Phases: Controlling the Selectivity between Silicon and Silicon Carbide via Magnesiothermic Reduction using Silica/Carbon Composites. Chem. Mater. 2016, 28 (5), 1526-1536. (34) Yan, L.; Hong, C.; Sun, B.; Zhao, G.; Cheng, Y.; Dong, S.; Zhang, D.; Zhang, X. In Situ Growth of Core-Sheath Heterostructural SiC Nanowire Arrays on Carbon Fibers and Enhanced Electromagnetic Wave Absorption Performance. ACS Applied Materials & Interfaces 2017, 9 (7), 6320-6331. (35) Han, M.; Yin, X.; Hou, Z.; Song, C.; Li, X.; Zhang, L.; Cheng, L. Flexible and Thermostable Graphene/SiC Nanowire Foam Composites with Tunable Electromagnetic Wave Absorption Properties. Acs Applied Materials & Interfaces 2017, 9 (13), 11803-11810. (36) Zhu, H. L.; Bai, Y. J.; Liu, R.; Lun, N.; Qi, Y. X.; Han, F. D.; Bi, J. Q. In situ synthesis of one-dimensional MWCNT/SiC porous nanocomposites with excellent microwave absorption properties. J. Mater. Chem. 2011, 21 (35), 13581-13587. (37) Wu, R.; Zhou, K.; Yang, Z.; Qian, X.; Wei, J.; Liu, L.; Huang, Y.; Kong, L.; Wang, L. Molten-salt-mediated synthesis of SiC nanowires for microwave absorption applications. Crystengcomm 2013, 15 (3), 570-576.

Synopsis Silicon carbide nanomaterials with high surface area and well-defined porosity were prepared from bio-based furfuryl alcohol as the carbon source.

TOC

20

ACS Paragon Plus Environment

Page 20 of 20