Solubility in the Na + SO4 + NO3 and Na + SO4 + NO2 Systems in

Feb 13, 2008 - Rebecca K. Toghiani*, Valerie A. Phillips, Laura T. Smith and Jeffrey S. ... Reid A. Peterson , Edgar C. Buck , Jaehun Chun , Richard C...
1 downloads 0 Views 139KB Size
798

J. Chem. Eng. Data 2008, 53, 798–804

Solubility in the Na + SO4 + NO3 and Na + SO4 + NO2 Systems in Water and in Sodium Hydroxide Solutions Rebecca K. Toghiani,*,†,‡ Valerie A. Phillips,‡ Laura T. Smith,‡ and Jeffrey S. Lindner‡ Dave C. Swalm School of Chemical Engineering and Institute for Clean Energy Technology, Mississippi State University, Mississippi State, Mississippi 39762

Solubility isotherms are reported for the binary systems, NaNO3 + Na2SO4 and NaNO2 + Na2SO4, in aqueous solution and in 1 m NaOH and 3 m NaOH solutions. Measurements were conducted at both (25 and 50) °C for the NaNO2 + Na2SO4 system and at (25, 35, and 50) °C for the NaNO3 + Na2SO4 system. The presence of either sodium nitrate or sodium nitrite in solution results in a reduction of the solubility of sodium sulfate. At 25 °C, a transition of the stable crystalline phase from sodium sulfate decahydrate to anhydrous sodium sulfate occurs as the amount of either sodium nitrate or sodium nitrite in aqueous solution increases. The presence of sodium hydroxide in solution also results in decreased solubility over the entire isotherm, with an increase in sodium hydroxide concentration giving rise to lower solubilities. In the NaNO3 + Na2SO4 system, the incongruent double salt, darapskite, NaNO3 · Na2SO4 · H2O, was identified as the stable crystalline phase over a portion of the solubility isotherm at all temperatures examined. TGA experiments were performed to determine the correct number of waters of hydration for darapskite.

Introduction The chemistry of sodium salts in high ionic strength solution is pertinent to the retrieval of saltcake from the waste tanks at the Hanford U.S. Department of Energy site in Richland, Washington, USA. Originating from the variety of processes that were employed during process demonstration and production runs at the site, the saltcake is one fraction of the 53 million gallons of legacy waste from the production of nuclear armaments; the other major fractions are liquid supernate and sludge. The presence of multiple anions, including nitrate, nitrite, sulfate, phosphate, fluoride, chloride, and carbonate in the waste, along with sodium originating from sodium hydroxide used to neutralize waste as it was placed in the tanks, gives rise to the formation of complex salts, such as the sodium-nitrate-sulfate double salt, more commonly known as darapskite, NaNO3 · Na2SO4 · H2O. Knowledge of the solubility isotherms for the binary systems sodium nitrate + sodium sulfate and sodium nitrite + sodium sulfate in the presence of sodium hydroxide will aid in the planning of saltcake retrieval operations at the Hanford site.

Literature Review Of interest in this work are the solubilities of sodium nitrate, of sodium nitrite and of sodium sulfate in an aqueous solution, and in sodium hydroxide solutions. Pelkhotkin and Bobrovskaya1 examined the ternary systems sodium nitrite + sodium hydroxide + water and sodium nitrate + sodium hydroxide + water. In addition to reporting solubility for these systems at (20 and 25) °C, the physical properties, density, viscosity, and refractive index, were reported as a function of composition. The solubility of sodium nitrite was given as 87.6 g * Corresponding author. Dave C. Swalm School of Chemical Engineering, P.O. Box 9595, Mississippi State University, Mississippi State, MS 39762. E-mail: [email protected]. † Dave C. Swalm School of Chemical Engineering. ‡ Institute for Clean Energy Technology.

(100 g H2O)-1 at 20 °C and 90.8 g (100 g H2O)-1 at 25 °C. For sodium nitrate in aqueous solution, solubilities of 81.8 g (100 g H2O)-1 and 88.0 g (100 g H2O)-1 were reported for (20 and 25) °C, respectively. In sodium hydroxide solution, the solubility of either sodium salt is reduced. For example, the addition of sodium hydroxide in the amount of 8.7 g (100 g H2O)-1 resulted in a solubility of 65.2 g NaNO3 (100 g H2O)-1 at 20 °C, while an addition of 9.1 g NaOH (100 g H2O)-1 resulted in a solubility of 70.1 g NaNO3 (100 g H2O)-1 at 25 °C. For sodium nitrite at 20 °C, the reported solubility was 68.7 g NaNO2 (100 g H2O)-1 in the presence of 7.4 g NaOH (100 g H2O)-1. At 25 °C, a solubility of 72.1 g NaNO2 (100 g H2O)-1 in the presence of 8.1 g NaOH (100 g H2O)-1 was reported by Pelkhotkin and Bobrovskaya. Kurnakow and Nikolajew2 also examined the solubility of sodium nitrate in sodium hydroxide solutions at 25 °C and at 65 °C. Selvaraj3 also examined the solubility of sodium nitrate in hydroxide solutions at 25 °C and at 50 °C. A discussion of the available literature data on sodium sulfate solubility as a function of temperature and as a function of sodium hydroxide in solution was presented in ref 4. Zhuravlev and Kolesnikova5 examined the solubility in aqueous solutions for the sodium nitrite + sodium sulfate system at (0, 25, and 50) °C . The solubility envelopes at 0 °C and at 50 °C each exhibited two distinct legs. At either (0 or 50) °C, one leg corresponds to sodium nitrite (NaNO2) as the equilibrium solid phase. At 0 °C, the other leg corresponds to an equilibrium solid phase of sodium sulfate decahydrate (Na2SO4 · 10H2O), while at 50 °C, this other leg corresponds to an equilibrium solid phase of anhydrous sodium sulfate (Na2SO4). At 25 °C, the solubility envelope exhibits three distinct legs, one corresponding to sodium sulfate decahydrate as the equilibrium solid phase at low nitrite loadings, one corresponding to anhydrous sodium sulfate as the equilibrium solid phase at moderate nitrite loadings, and one corresponding to sodium nitrite as the equilibrium solid phase at high nitrite

10.1021/je700666t CCC: $40.75  2008 American Chemical Society Published on Web 02/13/2008

Journal of Chemical & Engineering Data, Vol. 53, No. 3, 2008 799

loadings. The appearance of the third leg (corresponding to anhydrous sodium sulfate) at 25 °C is expected as the increased ionic strength of the solution suppresses the temperature at which the sodium sulfate decahydrate/anhydrous sodium sulfate phase transition occurs. In aqueous solution, this transition occurs at approximately 32.4 °C.6 No literature data were identified for the solubility of the sodium nitrite + sodium sulfate system in sodium hydroxide solutions. The ternary system, sodium nitrate + sodium sulfate + water, was examined by Chretien,7,8 by Foote,9 and by Makin.10 Chretien examined the solubility in this ternary system over the temperature range of (0 to 100) °C7 and as a component of a quaternary system over a slightly wider temperature range, (-21 to 121) °C.8 In this system, an incongruent double salt forms in a portion of the solubility envelope at certain temperatures. The molar ratio of sodium nitrate to sodium sulfate in the incongruent double salt is 1:1; however, the number of waters of hydration attributed to the double salt in the literature has been reported as one (NaNO3 · Na2SO4 · 1H2O)7–9 and as two (NaNO3 · Na2SO4 · 2H2O).10 Herting identified this double salt in a core sample from tank TX-113 at the Hanford site.11 This particular tank contains significant amounts of nitrate and sulfate in the saltcake fraction. Poletaev and Krasnenkova12 reviewed the NaNO3 + Na2SO4 + H2O system as part of an effort to examine nitrate and sulfate salts of sodium, rubidium, and cesium at (25 and 75) °C. They reported that the 25 °C isotherm consisted of four distinct regions, corresponding to Na2SO4 · 10H2O, Na2SO4, NaNO3 · Na2SO4 · 2H2O, and NaNO3, and that the 75 °C isotherm contained only two regions, corresponding to anhydrous Na2SO4 and to NaNO3. No literature data were identified for the solubility of the sodium nitrate + sodium sulfate system in sodium hydroxide solutions.

Experimental Section Materials. Sodium nitrite (> 99.6 %) and sodium nitrate (> 99.1 %) used in the solubility experiments were ACS reagent grade and purchased from Fischer Scientific. Anhydrous sodium sulfate (> 99.9 %) was purchased from Sigma Aldrich. Sodium hydroxide (> 98.7 %) was purchased from Fischer Scientific. Prior to use, sodium nitrite and sodium nitrate were pretreated by heating overnight in a muffle oven to remove any moisture. The pretreated chemicals were then stored in a desiccator until use. Sodium sulfate was heated at 110 °C overnight prior to use. Type I water with a resistivity less than 17.8 mΩ · cm-1 from a Barnstead Nanopure Infinity Water Purification System was used for all preparations. Standards for ion chromatography were purchased from Inorganic Ventures/UV Laboratories. Methods. All samples were prepared gravimetrically using an AND model GR-120 analytical balance accurate to ( 0.1 mg. Available literature data were used to guide the preparation of solutions when water was the solvent. Sufficient quantities of stock 1 m NaOH and 3 m NaOH solutions were mixed to allow all samples in 1 m NaOH or 3 m NaOH solutions to be prepared. The prepared samples were sealed, then placed in either a Precision Thelco Laboratory Oven (model 130D) or a Precision Low Temperature Incubator (model 815), both having sensitivities of 0.1 °C. Sealing of the samples during equilibration prevented exposure to atmospheric carbon dioxide and also prevented evaporation of water from the sample. The temperature was maintained at the desired equilibration temperature for the duration of equilibration. Previous experiments had demonstrated that approximately two weeks at the temperature was sufficient to ensure that liquid phase concentrations were no longer changing.4

After equilibration at that temperature for a period of two weeks, each sample was filtered using a Buckner funnel and maintained at that temperature using a water bath, which circulated water at the equilibration temperature through the funnel housing. Each sample was filtered into a vessel containing a premeasured mass of water to ensure that reprecipitation of solids did not occur in the filtrate. This step resulted in filtrate dilution, effectively lowering the hydroxide concentration in the sample by at least 50 %. The recovered diluted filtrate was stored in a sealed vial. Solids were collected on filter paper and then dried before weighing. Polarized light microscopy (PLM) was used to identify the crystalline phases present in the dried solids. The filtrate from each sample was analyzed using ion chromatography (IC), with dilutions required to obtain concentrations in the calibration range. These dilutions varied, depending on the sample. For sulfate, the calibration range was (0 to 150) ppm, with a detection limit of 0.06 ppm. For nitrate, the calibration range was (0 to 100) ppm, with a detection limit of 0.05 ppm. For nitrite, the calibration range was (0 to 100) ppm, with a detection limit of 0.02 ppm. Uncertainties in reported solubilities were evaluated for each data point using the standard deviation of repeated measurements or the detection limit (whichever was greater), along with the dilution factors employed in preparing the sample for IC analysis. The uncertainties were averaged for each component. The uncertainties in reported solubilities are 0.80 g NaNO2 (100 g H2O)-1, 0.93 g NaNO3 (100 g H2O)-1, and 0.41 g Na2SO4 (100 g H2O)-1. To determine the proper number of waters of hydration in the sodium nitrate sulfate double salt (darapskite), thermogravimetric analysis (TGA) was performed. A Perkin-Elmer/Pyris Diamond TGA/DTA 6300 (thermogravimetric analysis/differential thermal analysis) was employed for this purpose. The preparation method for darapskite detailed by Herting et al.13 was followed. Crystals formed during the equilibration period were confirmed as darapskite using polarized light microscopy. Two samples of the dried crystal (13.641 mg, 15.559 mg) were subjected to TGA, where the temperature was ramped and weight loss recorded as a function of time. During the heating, the water(s) of hydration are driven off, and the difference in the initial and final masses was used to determine the amount of water loss. The % mass lost was 4.997 % and 4.36 % of the initial mass for the two samples, respectively. This % mass loss is slightly less than the % mass lost that would correspond to 1 mol of hydration water per mole of sodium sulfate and of sodium nitrate. Thus, the molecular formula for darapskite is NaNO3 · Na2SO4 · 1H2O.

Results and Discussion The Environmental Simulation Program (ESP: OLI Systems, Inc.) was employed for aqueous electrolyte modeling in this work. For representation of the NaNO3 + Na2SO4 and NaNO2 + Na2SO4 systems in the presence of sodium hydroxide, representation of the systems NaNO3 + NaOH, NaNO2 + NaOH, and Na2SO4 + NaOH must reproduce the available literature data. Initial computations using the PUBLIC database within ESP V7.0 indicated that the pure component solubilities in water for each of the sodium salts (NaNO3, Na2SO4, and NaNO2) were well predicted; however, in the presence of sodium hydroxide, deviations between the available literature data and the model predictions were evident. To eliminate these deviations, and in the case of Na2SO4, also to allow the depression of the transition temperature for the phase transition between the anhydrous and decahydrate forms to be predicted, like-ion interactions were included in ESP and stored in a private

800 Journal of Chemical & Engineering Data, Vol. 53, No. 3, 2008 Table 1. Anion-Anion Interactions Considered for NaNO3 + NaOH, NaNO2 + NaOH, and Na2SO4 + NaOH Systems and Fitted Parameters, Obtained through Regression of Available Literature Data parameter

NO2-/OH-

NO3-/OH-

NaSO4-/OH-

SO42-/OH-

B1 B2 B3 C1 C2 C3 D1 D2 D3

0.05092964 1.65892e-04 0.0 -0.01699002 1.11407e-04 0.0 7.09137e-04 -7.80266e-06 0.0

-0.1220882 9.89048e-04 0.0 0.005315534 -4.47554e-05 0.0 4.25096e-05 -1.53349e-06 0.0

-0.196167 0.008436918 -4.02861e-05 0.007299739 -0.001050792 5.02556e-06 2.99648e-04 3.07256e-05 -1.50819e-07

0.06757067 -0.002195756 0.0 -0.00126333 6.42999e-05 0.0 1.23111e-04 4.66022e-06 0.0

In the PUBLIC database of ESP, only cation–anion, cation-neutral, anion-neutral, and/or neutral–neutral interactions have been included to represent known behaviors. Specifically, to improve predictions in the systems examined in this work, anion-anion interactions were defined, and regression of available literature data was performed to determine the set of parameters (Bi, Ci, Di) that best represents the data. The anion-anion interactions employed, along with the parameter set, are shown in Table 1. For both the NaNO2 + NaOH + H2O and NaNO3 + NaOH + H2O systems, inclusion of a single anion-anion interaction resulted in improved predictions of the influence of sodium hydroxide in solution on the solubility of the individual salt. Figure 1 provides a comparison of the literature data at 25 °C for the NaNO2 + NaOH + H2O system with the ESP V7.0 PUBLIC prediction and with the ESP V7.0, V7DBLSLT prediction. Representation is improved through inclusion of the like-ion interaction between nitrite and hydrox-

ide. Figure 2 provides a similar comparison for the NaNO3 + NaOH + H2O system at both (25 and 65) °C. While representation of the solubility envelope at 25 °C with the ESP V7.0 PUBLIC database agrees with available literature data, the solubility is overestimated somewhat at 65 °C, particularly at increased hydroxide loadings. The inclusion of the like-ion interaction between nitrate and hydroxide improved solubility representation at both temperatures. For the Na2SO4 + NaOH + H2O system, representation using a single like-ion interaction between sulfate and hydroxide ions failed to adequately capture the complex behavior exhibited by the available literature solubility data. In this system, the stable crystalline phase in aqueous solution is the sodium sulfate decahydrate, for temperatures up to 32.4 °C; however, anhydrous sodium sulfate is the stable crystalline phase in aqueous solution at temperatures above 32.4 °C. As evidenced in the literature data (Figure 3), the temperature at which this transition occurs is strongly influenced by the presence of sodium hydroxide in solution. The transition temperature is depressed significantly as the sodium hydroxide concentration is increased. The ESP V7.0 V7DBLSLT predictions shown in Figure 3 were obtained using two like-ion interactions, the SO4-2/OH- and the NaSO4-/ OH- interactions. Inclusion of both like-ion interactions provides for the complex behavior of this system to be adequately predicted. Solubilities in the NaNO2 + Na2SO4 system in aqueous solution and in (1 and 3) m NaOH solutions are reported in Tables 2 and 3, for temperatures of (25 and 50) °C, respectively. Also included in Tables 2 and 3 is the identification of the solid phase present at equilibrium with the liquid solution for each data point. The experimental pure component solubilities at 25

Figure 1. Effect of sodium hydroxide in solution on the solubility of pure sodium nitrite at 25 °C.

Figure 2. Effect of sodium hydroxide in solution on the solubility of pure sodium nitrate.

database (V7DBLSLT). The ion activity coefficient within ESP is represented using the Bromley-Zemaitis14,15 formalism

log(γi,j) )

-A|ZiZj|√I 1 + √I

+

(0.06 + 0.6B)|ZiZj|I + BI + 1.5 2 1 + |ZiZj|I

(

)

CI2 + DI3(1) where A is the Debye–Huckel constant; I is the ionic strength; Zi and Zj are the charge of the ions i and j, respectively; and B, C, and D are interaction constants, expressed as quadratic functions of temperature (only B is shown)

B ) B1 + B2T + B3T2

(2)

Journal of Chemical & Engineering Data, Vol. 53, No. 3, 2008 801 Table 3. Solubility in the Sodium Nitrite + Sodium Sulfate System in Water, 1 m NaOH, and 3 m NaOH Solutions at 50 °C/(g solute (100 g H2O)-1)

Figure 3. Effect of sodium hydroxide in solution on the solubility of pure sodium sulfate. Table 2. Solubility in the Sodium Nitrite + Sodium Sulfate System in Water, 1 m NaOH, and 3 m NaOH Solutions at 25 °C/(g solute (100 g H2O)-1) NaNO2

Na2SO4

NaOH

solid phase

0.000 9.741 26.317 30.583 40.366 53.549 75.485 80.879 81.424 81.686 87.685

In Aqueous Solution 28.291 0.000 26.910 0.000 20.110 0.000 16.959 0.000 10.580 0.000 5.904 0.000 3.595 0.000 2.839 0.000 2.490 0.000 1.103 0.000 0.000 0.000

Na2SO4 · 10H2O Na2SO4 · 10H2O Na2SO4 · 10H2O Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 + NaNO2 Na2SO4 + NaNO2 NaNO2 NaNO2

0.000 4.995 8.775 21.000 28.678 32.580 38.361 54.305 61.422 70.985 76.624 75.891 77.418 79.103

In 1 m NaOH Solution 24.93 4.000 24.595 4.000 22.095 4.000 19.062 4.000 13.402 4.000 13.060 4.000 7.931 4.000 3.702 4.000 3.080 4.000 2.370 4.000 2.394 4.000 1.524 4.000 1.273 4.000 0.000 4.000

Na2SO4 · 10H2O Na2SO4 · 10H2O Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 + NaNO2 Na2SO4 + NaNO2 NaNO2

0.000 7.119 16.503 23.419 29.716 50.857 59.417 61.746 66.100

In 3 m NaOH Solution 24.765 12.000 17.816 12.000 11.069 12.000 8.619 12.000 7.277 12.000 3.082 12.000 2.064 12.000 1.737 12.000 0.000 12.000

Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 + NaNO2 NaNO2

°C for sodium sulfate are 28.291 g Na2SO4 (100 g H2O)-1, 24.93 g Na2SO4 (100 g H2O)-1, and 24.765 g Na2SO4 (100 g H2O)-1 for aqueous, 1 m NaOH and 3 m NaOH solutions, respectively. At 50 °C, experimental solubilities for sodium sulfate are (46.340, 34.660, and 20.430) g Na2SO4 (100 g H2O)-1 in aqueous, 1 m NaOH and 3 m NaOH solutions. These values compare well with the literature data. For the aqueous and 1 m NaOH solutions, Na2SO4 · 10H2O was identified as the

NaNO2

Na2SO4

0.000 7.727 13.677 22.790 29.170 36.243 45.075 67.157 88.008 92.526 103.396

In Aqueous Solution 46.340 0.000 45.242 0.000 37.362 0.000 31.147 0.000 22.901 0.000 20.993 0.000 11.208 0.000 6.990 0.000 4.084 0.000 2.514 0.000 0.000 0.000

NaOH

solid phase Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 NaNO2

0.000 8.006 18.395 28.842 34.945 48.080 62.617 67.233 86.733 91.598 90.848 93.617

In 1 m NaOH Solution 34.660 4.000 28.545 4.000 25.328 4.000 16.319 4.000 12.704 4.000 10.018 4.000 6.155 4.000 5.789 4.000 3.205 4.000 1.516 4.000 1.480 4.000 0.000 4.000

Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 + NaNO2 Na2SO4 + NaNO2 NaNO2

0.000 5.671 14.730 24.401 42.857 60.460 66.530 66.496 67.235 68.940

In 3 m NaOH Solution 20.430 12.000 17.798 12.000 12.311 12.000 8.097 12.000 4.281 12.000 2.669 12.000 2.153 12.000 1.479 12.000 1.121 12.000 0.000 12.000

Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 Na2SO4 + NaNO2 NaNO2 NaNO2

solid phase at 25 °C, while in 3 m NaOH solution, anhydrous Na2SO4 was the solid phase in equilibrium with the liquid solution. At 50 °C, the solid phase in equilibrium with the liquid for aqueous, 1 m NaOH, and 3 m NaOH solutions is anhydrous Na2SO4. The pure component solubilities in the compilation by Linke and Seidell6 are 28 g Na2SO4 (100 g H2O)-1 at 25 °C and 46.4 g Na2SO4 (100 g H2O)-1 at 50 °C, and the experimental measurements in aqueous solution in this work agree well with these data. Pure component solubilities for sodium nitrite measured in the present work were also in agreement with available literature data. At 25 °C, the experimental solubilities were (87.685, 79.103, and 66.100) g NaNO2 (100 g H2O)-1, in aqueous, 1 m NaOH and 3 m NaOH solutions, respectively, compared to literature data of 87.6 g NaNO2 (100 g H2O)-1 in aqueous solution at 25 °C and 72.1 g NaNO2 (100 g H2O)-1 when 8.1 g NaOH per 100 g H2O is in solution (approximately 2 m NaOH). Again, the presence of sodium hydroxide in solution results in a significant decrease in the solubility of pure sodium sulfate and a slight decrease in the solubility of pure sodium nitrite. Solubility envelopes are shown in Figures 4 and 5 for the NaNO2 + Na2SO4 system at 25 °C and at 50 °C, respectively. At 25 °C in either aqueous solution or in 1 m NaOH solution, the solubility envelope consists of three distinct legs: at low concentrations of sodium nitrite in solution, the first leg corresponds to solutions in equilibrium with sodium sulfate decahydrate as the stable crystalline phase; at moderate to fairly high concentrations of sodium nitrite in solution, the liquid solution is in equilibrium with anhydrous sodium sulfate as the

802 Journal of Chemical & Engineering Data, Vol. 53, No. 3, 2008 Table 4. Solubility in the Sodium Nitrate + Sodium Sulfate System in Water, 1 m NaOH, and 3 m NaOH Solutions at 25 °C/(g solute (100 g H2O)-1) NaNO3

Figure 4. Solubility in the NaNO2 + Na2SO4 + NaOH + H2O system at 25 °C.

Na2SO4

NaOH

0.000 8.272 25.187 34.914 48.287 56.566 59.768 76.435 84.746 80.103 78.178 88.816 92.973 91.987

28.000 28.828 28.844 28.705 27.353 20.644 13.440 9.919 6.241 6.426 7.560 6.307 3.516 0.000

In Aqueous Solution 0.000 Na2SO4 · 10H2O 0.000 Na2SO4 · 10H2O 0.000 Na2SO4 · 10H2O 0.000 Na2SO4 0.000 Na2SO4 0.000 Na2SO4 0.000 Na2SO4 0.000 NaNO3 · Na2SO4 · 1H2O 0.000 NaNO3 · Na2SO4 · 1H2O 0.000 NaNO3 · Na2SO4 · 1H2O 0.000 NaNO3 · Na2SO4 · 1H2O 0.000 NaNO3 + NaNO3 · Na2SO4 · 1H2O 0.000 NaNO3 0.000 NaNO3

solid phase

0.00 9.037 17.336 23.395 35.608 42.651 67.457 84.260

24.930 29.342 26.847 17.664 13.912 10.999 5.701 0.000

In 1 m NaOH Solution 4.000 Na2SO4 · 10H2O 4.000 Na2SO4 · 10H2O 4.000 Na2SO4 4.000 Na2SO4 4.000 NaNO3 · Na2SO4 · 1H2O 4.000 NaNO3 · Na2SO4 · 1H2O 4.000 NaNO3 + NaNO3 · Na2SO4 · 1H2O 4.000 NaNO3

0.000 0.787 2.085 3.829 20.720 27.209 35.223 47.550 52.903 63.720 64.337 62.153 66.176 67.191

25.030 23.316 23.757 22.663 17.765 15.933 11.779 7.286 6.439 4.416 3.860 3.045 1.692 0.000

In 3 m NaOH Solution 12.000 Na2SO4 12.000 Na2SO4 12.000 Na2SO4 12.000 Na2SO4 12.000 Na2SO4 12.000 NaNO3 · Na2SO4 · 1H2O 12.000 NaNO3 · Na2SO4 · 1H2O 12.000 NaNO3 + NaNO3 · Na2SO4 · 1H2O 12.000 NaNO3 + NaNO3 · Na2SO4 · 1H2O 12.000 NaNO3 12.000 NaNO3 12.000 NaNO3 12.000 NaNO3 12.000 NaNO3

Table 5. Solubility in the Sodium Nitrate + Sodium Sulfate System in Water at 35 °C/(g solute (100 g H2O)-1) Figure 5. Solubility in the NaNO2 + Na2SO4 + NaOH + H2O system at 50 °C.

stable crystalline phase; and at very high concentrations of sodium nitrite and low concentrations of sodium sulfate, the stable crystalline phase is sodium nitrite. In 3 m NaOH at 25 °C and in all solutions (aqueous, 1 m NaOH, 3 m NaOH) at 50 °C, the solubility envelope consists only of two distinct legs, one corresponding to anhydrous sodium sulfate as the solid phase precipitate and one corresponding to sodium nitrite as the solid phase precipitate. The presence of sodium nitrite in solution has the effect of significantly lowering the sodium sulfate solubility, whether in aqueous solution or in caustic solutions. Also depicted in Figures 4 and 5 are solubility envelope predictions obtained using ESP V7.0 with the V7DBLSLT database. The representation obtained with ESP was improved through incorporation of a like-ion interaction between the nitrite ion and the sulfate ion (NO2-/SO42interaction), and these are the ESP predictions shown in these figures. Solubilities in the NaNO3 + Na2SO4 system in aqueous solution and in (1 and 3) m NaOH solutions are reported in Tables 4, 5, and 6, for temperatures of (25, 35, and 50) °C, respectively. The identification of the solid phase/phase(s) present at equilibrium with the liquid solution is also given for

NaNO3

Na2SO4

solid phase

0.000 20.553 42.197 65.233 61.329 79.749 87.002 94.302 97.098 107.880

57.649 43.256 25.633 15.770 14.047 12.592 9.891 5.993 5.143 0.000

Na2SO4 Na2SO4 Na2SO4 NaNO3 · Na2SO4 · 1H2O NaNO3 · Na2SO4 · 1H2O NaNO3 · Na2SO4 · 1H2O NaNO3 · Na2SO4 · 1H2O NaNO3 + NaNO3 · Na2SO4 · 1H2O NaNO3 + NaNO3 · Na2SO4 · 1H2O NaNO3

each data point. The presence of sodium hydroxide has a significant impact on the solubility in this system at (25 and 50) °C. Solubility envelopes are shown in Figures 6 and 7 for these temperatures. Experimental data are shown along with available literature data and predictions using ESP V7.0 with V7DBLSLT. The representation obtained with ESP was improved through incorporation of a like-ion interaction between the nitrate ion and the sulfate ion (NO3-/SO42- interaction). At 25 °C, the solubility envelope consists of four distinct legs. At low concentrations of sodium nitrate, the equilibrium solid phase is sodium sulfate decahydrate. The phase transition to anhydrous sodium sulfate occurs at 25 °C, and Na2SO4 is the equilibrium solid phase, once the sodium nitrate concentration exceeds approximately 30 g NaNO3 (100 g H2O)-1. The third leg of the solubility envelope corresponds to the double salt,

Journal of Chemical & Engineering Data, Vol. 53, No. 3, 2008 803 Table 6. Solubility in the Sodium Nitrate + Sodium Sulfate System in Water, 1 m NaOH, and 3 m NaOH Solutions at 50 °C/(g solute (100 g H2O)-1) NaNO3

Na2SO4

NaOH

0.000 0.000 4.815 8.693 26.835 38.465 51.346 63.432 83.963 80.170 102.945 103.234 107.712 116.535 113.879 115.451

46.340 45.407 39.773 35.639 27.151 18.481 13.231 12.167 9.729 9.759 8.268 7.036 5.713 4.503 2.976 0.000

In Aqueous Solution 0.000 Na2SO4 0.000 Na2SO4 0.000 Na2SO4 0.000 Na2SO4 0.000 Na2SO4 0.000 Na2SO4 0.000 Na2SO4 0.000 Na2SO4 0.000 NaNO3 · Na2SO4 · 1H2O 0.000 NaNO3 · Na2SO4 · 1H2O 0.000 NaNO3 + NaNO3 · Na2SO4 · 1H2O 0.000 NaNO3 + NaNO3 · Na2SO4 · 1H2O 0.000 NaNO3 0.000 NaNO3 0.000 NaNO3 0.000 NaNO3

solid phase

0.000 10.299 25.115 38.892 49.271 62.385 67.567 83.524 86.761 108.513 109.186

34.660 33.533 21.705 17.499 13.431 10.807 8.636 8.462 5.917 0.000 0.000

In 1 m NaOH Solution 4.000 Na2SO4 4.000 Na2SO4 4.000 Na2SO4 4.000 Na2SO4 4.000 Na2SO4 4.000 Na2SO4 4.000 Na2SO4 4.000 NaNO3 · Na2SO4 · 1H2O 4.000 NaNO3 + NaNO3 · Na2SO4 · 1H2O 4.000 NaNO3 4.000 NaNO3

0.000 0.000 2.012 4.296 7.977 8.779 18.282 42.555 60.265 77.359 81.604 91.566 90.523

20.430 20.385 21.705 18.296 17.871 16.469 11.833 7.845 4.830 2.891 2.418 2.381 0.000

In 3 m NaOH Solution 12.000 Na2SO4 12.000 Na2SO4 12.000 Na2SO4 12.000 Na2SO4 12.000 Na2SO4 12.000 Na2SO4 12.000 Na2SO4 12.000 Na2SO4 12.000 Na2SO4 12.000 Na2SO4 12.000 NaNO3 12.000 NaNO3 12.000 NaNO3

NaNO3 · Na2SO4 · 1H2O, as the equilibrium solid phase and occurs at sodium nitrate levels over a fairly narrow range of

Figure 7. Solubility in the NaNO3 + Na2SO4 + NaOH + H2O system at 50 °C.

between approximately (75 to 85) g NaNO3 (100 g H2O)-1. Finally, at high levels of sodium nitrate in solution, the equilibrium solid phase is NaNO3. The combined effects of both sodium hydroxide and sodium nitrate are to lower the salt solubility. In 1 m NaOH solutions, the solubility envelope at 25 °C consists of the same four distinct legs, while in 3 m NaOH solutions, only three distinct legs are present. At this concentration of sodium hydroxide in solution, the transition to anhydrous sodium sulfate as the equilibrium solid phase at 25 °C occurs for solutions containing only sodium sulfate. At 50 °C, the solubility envelopes in water and in 1 m NaOH solutions exhibit three distinct legs, one corresponding to anhydrous sodium sulfate as the equilibrium solid phase, the middle leg corresponding to the sodium nitrate/sodium sulfate double salt as the equilibrium solid phase, and the third leg corresponding to pure sodium nitrate as the equilibrium solid phase. In 3 m NaOH solution, only two branches were present in the solubility envelope, one corresponding to anhydrous sodium sulfate and one corresponding to sodium nitrate as the equilibrium solid phase, respectively. Formation of the double salt was not observed in solutions containing the higher sodium hydroxide concentration at 50 °C. This behavior is explained by considering the presence of sodium hydroxide in solution lowering the temperature at which a phase transition can occur. The solubility envelope reported for this system in aqueous solution at 75 °C by Poletaev and Krasnenkova12 consisted only of two distinct branches, with no formation of the double salt. The presence of 3 m sodium hydroxide in solution is sufficient to eliminate the branch corresponding to the double salt at 50 °C in the present work.

Conclusions

Figure 6. Solubility in the NaNO3 + Na2SO4 + NaOH + H2O system at 25 °C.

Solubilties in the NaNO2 + Na2SO4 + NaOH + H2O and NaNO3 + Na2SO4 + NaOH + H2O systems have been measured at two temperatures, (25 and 50) °C, and in aqueous solution, as well as in 1 m NaOH and 3 m NaOH solutions. Data obtained in this work have been combined with available literature data to obtain like-ion interaction parameters for these systems, which result in improved predictive capabilities for these systems within the ESP V7.0 program. In the NaNO3 + Na2SO4 system, the sodium nitrate + sodium sulfate double salt was observed under differing conditions. While observed

804 Journal of Chemical & Engineering Data, Vol. 53, No. 3, 2008

at 25 °C in aqueous, 1 m NaOH, and 3 m NaOH solutions, this double salt was only observed in aqueous and in 1 m NaOH solutions at 50 °C. TGA confirmed that the sodium nitrate + sodium sulfate double salt contained no more than one water of hydration, and its corresponding molecular formula is NaNO3 · Na2SO4 · 1H2O.

Literature Cited (1) Plekhotkin, V. F.; Bobrovskaya, L. P.; Trishin, V. M. Ternary isothermal invariant points in sodium nitrate-sodium nitrite-sodium hydroxide-water and sodium nitrate-sodium nitrite-sodium carbonatewater systems at 25 deg. Tr. Gos. Inst. Prikl. Khim 1970, 66, 169– 173. (2) Kurnakov, N. S.; Nikolaev, V. I. The peculiar fold of sodium nitrate. Z. Phys. Chem 1927, 130, 193–204. (3) Selvaraj, D. Solubility Studies on the Na-F-PO4 System in Sodium Nitrate and in Sodium Hydroxide Solutions, M.S. Thesis, Mississippi State University, 2003. (4) Toghiani, R. K.; Phillips, V. A.; Lindner, J. S. Solubility of Na-FSO4 in Water and in Sodium Hydroxide Solutions. J. Chem. Eng. Data 2005, 50, 1616–1619. (5) Zhuravlev, E. F.; Kolesnikova, A. S. Solubility in water-salt systems containing sodium and potassium nitrites. Zh. Neorg. Khim. 1968, 13, 2593–2596. (6) Linke, W. F.; Seidell, A. Solubilities, inorganic and metal organic compounds: a compilation of solubility data from the periodical literature, 4th ed.; Van Nostrand: Princeton, N. J., 1958.

(7) Chretien, A. The ternary system: water-sodium sulfate-sodium nitrate. Compt. Rend. 1929, 188, 1047–1050. (8) Chretien, A. The quaternary system; water, sodium nitrate, sodium chloride and sodium sulfate. Anal. Chim. 1929, 12, 9–155. (9) Foote, H. W. The system sodium nitrate-sodium sulfate-water, and the minerals darapskite and nitroglauberite. Am. J. Sci. 1925, 9, 441– 447. (10) Makin, A. V.; Ushinskii, K. D. The sodium nitrate-sodium sulfatewater system at 25 °C. Zh. Neorg. Khim. 1959, 4, 1190–1197. (11) Herting, D. L. Saltcake Dissolution FY 2000 Status Report;HNF-7031, Rev. 0., September 2000. (12) Poletaev,I.F.;Krasnenkova,L.V.Sodium(1+),rubidium(1+).dvr.nitrate(1-),sulfate(2-)-waterandsodium(1+),cesium(1+).dvr.nitrate(1-),sulfate(2-)-water systems at 25 and 75.deg. Zh. Neorg. Khim. 1976, 20, 2250–2256. (13) Herting, D. L.; Cooke, G. A.; Warrant, R. W. Identification of Solid Phases in Saltcake from Hanford Site Waste Tanks;HNF-11585, Rev. 0, September 2002. (14) Zemaitis, J. F., Jr.; Clark, D. M.; Faral, M.; Scrivner, N. C. Handbook of Aqueous Electrolyte Thermodynamics; AIChE: New York, NY, 1986. (15) OLI Systems, Inc., OLI Data Analysis: An Overview of Data Analysis and Data Entry for OLI Programs, 2006. Received for review November 13, 2007. Accepted December 28, 2007. The authors acknowledge support from the United States Department of Energy to the Institute for Clean Energy Technology under Cooperative Agreements No. DE-FC26-98FT40395 and DE-FC01-05EW-07029.

JE700666T