Sorption of Fluorotelomer Sulfonates, Fluorotelomer Sulfonamido

Oct 2, 2017 - Environmental Science & Technology 2018 Article ASAP ... A review of emerging technologies for remediation of PFASs. Ian Ross , Jeffrey ...
0 downloads 0 Views 1MB Size
Subscriber access provided by UNIV OF ESSEX

Article

Sorption of Fluorotelomer Sulfonates, Fluorotelomer Sulfonamido Betaines, and a Fluorotelomer Sulfonamido Amine in National Foam Aqueous Film-Forming Foam to Soil Krista A. Barzen-Hanson, Shannon E. Davis, Markus Kleber, and Jennifer A. Field Environ. Sci. Technol., Just Accepted Manuscript • DOI: 10.1021/acs.est.7b03452 • Publication Date (Web): 02 Oct 2017 Downloaded from http://pubs.acs.org on October 3, 2017

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Environmental Science & Technology is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 32

Environmental Science & Technology

1 2

Sorption of Fluorotelomer Sulfonates, Fluorotelomer Sulfonamido Betaines, and a Fluorotelomer Sulfonamido Amine in National Foam Aqueous Film-Forming Foam to Soil

3

Krista A. Barzen-Hanson,a Shannon E. Davis,a,b Markus Kleber,c and Jennifer A. Fieldd*

4 5 6 7 8 9 10 11 12

a

Department of Chemistry, Oregon State University, 153 Gilbert Hall, Corvallis, Oregon 97331, United States b Currently at School for the Environment, University of Massachusetts, Boston, 100 William T Morrissey Boulevard, Boston, MA 02125, United States c Department of Crop and Soil Science, Oregon State University, 3017 ALS Building, 2750 SW Campus Way, Corvallis, OR 97331, United States d Department of Environmental and Molecular Toxicology, Oregon State University, 1007 ALS Building, 2750 SW Campus Way, Corvallis, Oregon 97331, United States *Corresponding author

13 14 15

Address: Oregon State University, 1007 ALS Building, 2750 SW Campus Way, Corvallis, OR 97331. Phone: (541) 737-2265. Fax: (541) 737-0497. E-mail: [email protected]

16

1 ACS Paragon Plus Environment

Environmental Science & Technology

Page 2 of 32

17

ABSTRACT

18

During fire fighter training, equipment testing, and emergency responses with aqueous film-

19

forming foams (AFFFs), mg/L concentrations of anionic, zwitterionic, and cationic per- and

20

polyfluoroalkyl substances (PFASs) enter the environment. Since the behavior of zwitterionic

21

and cationic PFASs in the subsurface is unknown, batch sorption experiments were conducted

22

using National Foam AFFF, which contains anionic fluorotelomer sulfonates (FtSs), zwitterionic

23

fluorotelomer sulfonamido betaines (FtSaBs), and cationic 6:2 fluorotelomer sulfonamido amine

24

(FtSaAm). Sorption of the FtSs, FtSaBs, and 6:2 FtSaAm to six soils with varying organic

25

carbon, effective cation exchange capacity, and anion exchange capacity was evaluated to

26

determine sorption mechanisms. Due to poor recovery of the FtSaBs and 6:2 FtSaAm with

27

published PFAS soil extraction methods, a new soil extraction method was developed to achieve

28

good (90-100 %) recoveries. The 6:2 FtSaAm was depleted from the aqueous phase in all but

29

one soil, which is attributed to electrostatic and hydrophobic interactions. Sorption of the FtSs

30

was driven by hydrophobic interactions, while the FtSaBs behave more like cations that strongly

31

associate with the solid phase relative to groundwater. Thus, the sorption mechanisms of the

32

FtSs, FtSaBs, and 6:2 FtSaAm are more complex than expected and cannot be predicted by bulk

33

soil properties.

34

2 ACS Paragon Plus Environment

Page 3 of 32

35 36

Environmental Science & Technology

INTRODUCTION Per- and polyfluoroalkyl substances (PFASs) are ubiquitous contaminants in the

37

environment1-3 and in wildlife,4,5 in part due to the release of aqueous film-forming foams

38

(AFFFs) during fire-related emergencies, equipment testing, and training. AFFFs are complex

39

mixtures that contain solvents, hydrocarbon surfactants, and anionic, zwitterionic, and cationic

40

PFASs.6,7 Because AFFFs are proprietary mixtures, the composition8-11 and concentrations12 of

41

PFASs in AFFFs were reverse-engineered to understand their environmental impact. At the time

42

of application, AFFFs are diluted to either 3% or 6%,6,7 resulting in high (mg/L) concentrations

43

of PFASs12 that subsequently enter the environment.

44

Sorption of perfluoroalkyl carboxylates (PFCAs) and perfluoroalkyl sulfonates (PFSAs)

45

increases with the organic carbon content in soils and sediments,13-16 as measured by solid-water

46

partition coefficients (Kd) and organic carbon normalized solid-water partition coefficients. The

47

contributions to sorption of PFSAs and PFCAs from electrostatic interactions with mineral

48

phases increases when organic carbon is low (0-0.78%).14,17 Within the PFCA or PFSA

49

homologous series, longer-chained homologs have higher partition coefficients than short-

50

chained homologs.15,16,18-20

51

In contrast, the anionic fluorotelomer sulfonates (FtSs) and zwitterionic and cationic

52

PFASs present in groundwater,12 soil,21,22 and sediment23-25 have received little attention. Two

53

studies report field-derived Kd values for the 6:2 FtS,23,26 while only one study reports field-

54

derived Kd values for the zwitterionic 6:2 fluorotelomer sulfonamido betaine (FtSaB) and the

55

cationic 6:2 fluorotelomer sulfonamido amine (FtSaAm).23 The ‘n:2’ fluorotelomer-based

56

PFASs are characterized by carbon chains with ‘n’ perfluorinated carbons that are bonded to two

57

non-fluorinated methylene carbons. For example, 6:2 FtS has six perfluorinated carbons that are

58

bonded to two non-fluorinated methylene carbons that are then bonded to a sulfonate group.

59

Typically, batch sorption experiments containing a mixture of PFCAs and PFSAs are

60

performed under controlled conditions.15,16,20 However, a similar experimental set-up for

61

sorption of zwitterionic and cationic PFASs is challenging due to the lack of authentic standards

62

and mass-labeled internal standards for the zwitterionic and cationic PFASs, and few reference

63

materials are available.12 Furthermore, mass balance of the PFCAs and PFSAs is typically 3 ACS Paragon Plus Environment

Environmental Science & Technology

Page 4 of 32

64

achieved by extracting the soil or sediment.15,16 To date, all studies examining concentrations of

65

zwitterionic and cationic PFASs on soil and sediment rely on extracting with methanol and either

66

1.5-200 mM acid or base. However, this approach has only been validated by spiking dry soils

67

with standards dissolved in methanol and allowing the methanol to evaporate for 2-48 h.22-24,27

68

Others demonstrate that higher concentrations of acid (e.g. 0.5-1 M) in methanol are necessary to

69

quantitatively recover cations, particularly if the cations have been allowed to equilibrate in

70

water with the soil and/or sediment.28-31 If a higher concentration of acid in methanol for the

71

extraction of zwitterionic and cationic PFASs from soil, then both concentrations24,25,27 and field-

72

derived Kd estimates23 of zwitterionic and cationic PFASs may be significantly underestimated

73

due to incomplete extraction of the (presumably) equilibrated soil and sediment.

74

It is difficult to simulate the complexity of processes that occur at AFFF-impacted field

75

sites during sorption experiments. To the best of our knowledge, only two studies report PFCA

76

and PFSA sorption in the presence of ionized hydrocarbon surfactants,15,32 which occur at similar

77

levels to PFASs in AFFFs along with solvents.6,7 Of the two studies, one reports an increase in

78

the sorption of a single compound, perfluorooctane sulfonate (PFOS), in the presence of a single

79

cationic hydrocarbon surfactant, and another single anionic hydrocarbon surfactant decreased

80

PFOS sorption.32 In the second study, another anionic hydrocarbon surfactant caused either no

81

change or a slight decrease in sorption of long-chained (n ≥ 6) perfluoroalkyl acids when present

82

in a mixture of PFASs.15 However, neither of the two studies employed conditions that

83

simulated the application of AFFF that contain mg/L levels of PFASs and other additives to

84

pristine soil at a field site.

85

Little is known about the sorption behavior of anionic, zwitterionic, and cationic PFASs

86

present in AFFF, especially once concentrated AFFF is applied to soils at field sites. To the best

87

of our knowledge, batch sorption experiments have not been conducted using AFFF containing a

88

range of PFASs and concentrations in the same range as those found in groundwater (ng/L to

89

mg/L) and AFFF applied to fight fires (mg/L to g/L). National Foam AFFF was selected because

90

it was approved for use by the U.S. military since 1976,9 contains anionic FtSs, zwitterionic

91

FtSaBs, and cationic 6:2 FtSaAm (Fig. 1),9,12 and is still available today on the Qualified Product

92

List.33,34 The anionic FtSs are predicted to sorb via hydrophobic interactions as observed for

93

PFAAs,14-16,35 while zwitterionic FtSaBs and cationic 6:2 FtSaAm are expected to sorb via 4 ACS Paragon Plus Environment

Page 5 of 32

Environmental Science & Technology

94

electrostatic interactions in a manner analogous to zwitterionic and cationic pharmaceuticals.36-38

95

Six uncontaminated soils with ranging levels of organic carbon, effective cation exchange

96

capacity (ECEC), and anion exchange capacity (AEC) were used to investigate the sorption

97

mechanisms of the FtSs, FtSaBs, and 6:2 FtSaAm contained in National Foam AFFF. While

98

sorbate competition is possible, assessing sorbate competition was outside the scope of the study.

99

Due to the potential for sorbates (FtSaBs, 6:2 FtSaAm), organic matter, and iron oxides to

100

speciate over a range of pHs, the influence of pH on the sorption of the anionic FtSs, zwitterionic

101

FtSaBs, and cationic 6:2 FtSaAm sorption was determined with a single soil titrated to pH 4 and

102

pH 7 as well as the native pH (pH 5.1). Existing soil extraction methods for zwitterionic and

103

cationic PFASs22-24,27 did not provide adequate mass balance; therefore, a new soil extraction

104

method was developed to enable complete mass balance.

105

EXPERIMENTAL

106

Chemicals. A description of all materials, including solvents, chemicals, and analytical

107

standards, is provided in the Supporting Information (SI).

108

Soil Sample Collection and Characterization. Six uncontaminated soils (Soils 1-6) were

109

selected from an archived soil collection at Oregon State University that constrained pH to 5.0-

110

5.5 but covered a range of soil characteristics, including organic carbon, ECEC, and AEC (Table

111

1, Table S1). Methods for soil characterization are provided in the SI. All soil characterization

112

was performed prior to autoclaving, which is known to change organic matter structure and alter

113

the clay fraction.39 Soils were sieved to < 2 mm and air dried prior to homogenization with a

114

mortar and pestle before use in sorption experiments.

115

Batch Sorption Experiments. Analyte Source Selection. Analyte sources and rationale are

116

provided in the SI.

117

Sorption Isotherm Experiment. All isotherms, with the exception of the preliminary experiment

118

involving a commercial Capstone product (see SI), were created using National Foam AFFF.

119

Material Safety Data Sheets for National Foam AFFF indicate 4-25 % solvent,7 but after dilution

120

in surrogate groundwater, solutions were comprised of < 0.1 % organic solvent. A 21-point

121

isotherm was constructed using Soil 1, with initial aqueous phase concentrations (Cwi) of 1.8 –

122

240,000 nM for the 6:2 FtSaB. Eleven-point isotherms were constructed using Soils 2-6, and 5 ACS Paragon Plus Environment

Environmental Science & Technology

Page 6 of 32

123

two additional isotherms were constructed with Soil 1 that was titrated to pH 4 and pH 7. For the

124

11-point isotherms, Cwi ranged from 1.8 to 440 nM for the 6:2 FtSaB. The upper-end Cwi for the

125

21-point and the 11-point isotherms were selected based on the 3% AFFF in water used in

126

firefighting and a mid-range concentration for the 6:2 FtS in AFFF-impacted groundwater (21 –

127

520 nM),12 respectively. Since all analytes were delivered as a mixture, only the concentration

128

range for the most abundant analyte is reported here; the remaining concentration ranges and the

129

relative ratios of each analyte are given in Table S2 and Table S3, respectively (see SI).

130

Replicates, which consisted of homogenized soil spiked with the same volume of National Foam

131

AFFF stock solution, were created for 6:2 FtSaB Cwi of 8.8 nM (n=4), 110 nM (n=3), and

132

240,000 nM (n=3). All other data are derived from individual reactors.

133

Homogenized soil was weighed (1.00 ± 0.02 g) into each 50 mL polypropylene

134

centrifuge tube (VWR, Radnor, PA) and autoclaved for 40 min at 121 °C with a 20-min drying

135

time (Consolidated Sterilizer Systems Model SSR-2A-ADVPB, Allston, MA). Vials contained

136

the autoclaved soil and 10 mL of a groundwater surrogate (0.5 mM calcium chloride),16,35 to

137

which only the diluted National Foam AFFF was spiked (Table S4; see SI). The soil-water ratio

138

was optimized for the primary component in the AFFF (6:2 FtSaB). Because the ratios of all

139

components were fixed in the AFFF and standards for the individual AFFF components are not

140

available commercially, the solution composition could not be optimized for all components.

141

Positive controls, consisting of groundwater surrogate and AFFF but no soil, were prepared at

142

the Cwi of the replicates. One negative control, consisting of the autoclaved soil and groundwater

143

surrogate but no AFFF, was prepared with each isotherm. Vials were allowed to equilibrate for

144

24 h on a wrist action shaker at 10° rotation (Burrell Corporation, Model 75, Pittsburg, PA)

145

based on previous literature (see SI).13,17,32,35

146

Following equilibration, batch reactors were centrifuged at 2808 rcf for 20 min

147

(Eppendorf, Model 5810R, Hauppauge, NY), and the supernatant was decanted into a separate

148

15 mL centrifuge tube (VWR). The soil was transferred into a separate 50 mL centrifuge tube

149

using deionized water. The empty vial from which the aqueous and soil phases had been

150

removed (hereafter referred to as ‘vial phase’) and the aqueous phase were stored at -20 °C. The

151

soil was freeze dried (VirTis Sentry 2.0, SP Scientific, Warminster, PA) for 48 h and stored in

152

the dark at 22 °C until extraction. 6 ACS Paragon Plus Environment

Page 7 of 32

153

Environmental Science & Technology

pH Adjustments to Pre-equilibrated Soil. Methods for pH adjusting the soils are provided

154

in the SI. Briefly, soil was pre-equilibrated with groundwater surrogate for 24 h, over-titrated to

155

either pH 3.3 or pH 8, and pre-equilibrated for another 24 h before AFFF was spiked.

156

Sample Preparation. Aqueous Phase. The aqueous phase sample preparation was based on a

157

slight modification of a micro liquid-liquid extraction, as established previously.12 A description

158

is provided in the SI.

159

Soil phase. Mass balance experiments consisted of quadruplicate vials of Soil 1 with 110 nM 6:2

160

FtSaB Cwi. Following equilibration for 24 h, the three phases were separated and extracted

161

individually. Initially, mass balance experiments were conducted using the aqueous phase

162

extraction and a soil extraction typically used for cationic and zwitterionic PFASs.23,24,27 The

163

vial and soil phases were extracted using 1.5 mM ammonium hydroxide in methanol as

164

described elsewhere.27 Preliminary experiments indicated poor recovery of the zwitterionic 6:2

165

FtSaB and the cationic 6:2 FtSaAm (Table S6) when soil and analytes were equilibrated in an

166

aqueous phase (and not methanolic spikes) and extracted using relatively mild conditions (1.5-

167

200 mM base in methanol22,24,27).

168

Soil extraction methods for cationic, nonfluorinated surfactants typically use either 0.5

169

M30 or 1 M HCl28,29,31 in methanol. The 1 M HCl in methanol extraction conditions proved to be

170

problematic (unpublished data). Therefore, 0.5 M HCl in methanol was used in all subsequent

171

extractions. The soil extraction procedure was modified slightly from Houtz et al.27 and is

172

outlined in the SI.

173

Mass balance experiments were repeated using the acidic methanol extraction for the vial

174

and soil phases. Recoveries improved significantly for the 6:2 FtSaB and the 6:2 FtSaAm (90-

175

100 % recovery; Table S6). Having achieved mass balance in separate experiments with an

176

experimental set-up analogous to that used to generate isotherms, mass balance was assumed for

177

all vials. Mass balances were not determined for each vial used to construct the isotherms due to

178

the greater variability associated with subsampling the AFFF concentrate, and therefore, the

179

variability in the mass of analyte added to each vial. Mass balance experiments also indicated

180

that sorption to the vial walls was minimal for all analytes (unpublished data). Therefore, only

7 ACS Paragon Plus Environment

Environmental Science & Technology

Page 8 of 32

181

the aqueous and soil phases were extracted for each vial (not the vial itself).

182

LOD and LOQ parameters for soil extractions (Table S7) and descriptions are provided in the SI.

183

Analytical Methods. A description of the analytical methods, including chromatography,

184

MS/MS, calibration, analyte quality classification, and quality control measures, is based on

185

previous literature10,12 and provided in the SI.

186

Data Treatment. Measured soil phase concentrations for each analyte were adjusted to account

187

for the mass of each analyte remaining in the pore water that was forced onto the soil during

188

freeze drying (see SI for details).

189

Whole method

Sorption isotherms were fitted using the following Freundlich isotherm model equations:

190

 =   (Eqn 1) or  =  +  (Eqn 2)

191

where Kf [(nmol kg-1)(nmol L-1)-n] is the Freundlich sorption coefficient and n (unitless) is a

192

measure of nonlinearity and represents the free energy associated with adding more sorbate to

193

the sorbent.40 Kf values (Table S8) were converted to the concentration-specific Kd values using

194

the following equation:

195

 =  ∗  (Eqn 3)

196

where Cw is the equilibrium concentration of the aqueous phase in the 8.8 or 110 nM Cwi vials, to

197

enable comparisons between isotherms and across other sorption studies for other PFASs (see SI

198

for details). The Kd values at Cwi = 110 nM are used for the FtSs and the 6:2 FtSaAm, while the

199

Kd values at Cwi = 8.8 nM are used for the FtSaBs in the discussion below (see SI for rationale).

200

Statistical Analysis. Correlation coefficients, 95% confidence intervals (CI), and p-values were

201

calculated for all correlations using R (version 3.3.3).41 Correlations were computed using

202

Pearson’s moment correlations and did not incorporate the 95% CI of each Kd value. Correlation

203

coefficients and p-values are interpreted with caution due to the non-normal distribution of the

204

soil property values.

205

pKa. pKas for the functional groups on FtSs, FtSaBs, and FtSaAms were estimated by comparing

206

the molecules to model compounds in the literature (see SI) and using the estimation software

207

Chemicalize42 (Fig. 1). 8 ACS Paragon Plus Environment

Page 9 of 32

Environmental Science & Technology

208

RESULTS AND DISCUSSION

209

Commercial Product vs. AFFF. Preliminary experiments were performed to determine if the

210

sorption of the 6:2 FtSaB from the Capstone product and National Foam AFFF at low

211

concentrations (1.8 – 18 nM) was significantly different at the 95% CI (Fig. S3). This

212

information was used to select the most appropriate product with which to conduct subsequent

213

sorption experiments. No significant difference in the sorption of the 6:2 FtSaB between the

214

Capstone product and National Foam AFFF was observed. The Capstone product is a simple

215

mixture containing only 6:2 FtS, 6:2 FtSaB, and 6:2 FtSaAm with no hydrocarbon surfactants

216

but percent levels of solvent,43 while National Foam AFFF contains the analytes plus percent

217

levels of solvents and hydrocarbon surfactants.7 Given the AFFF’s greater complexity and the

218

fact that the AFFF has been used since the 1970s and is still listed on the U.S. Military’s

219

Qualified Products List,33,34 all subsequent sorption experiments were performed with National

220

Foam AFFF.

221

Sorption Isotherms. Sorption experiments with National Foam AFFF were conducted using six

222

soils, with a subset of experiments conducted with a single soil (Soil 1) but at three different pHs

223

(pH 4, 5.1, and 7). The objective was to test soils over a range of properties in order to

224

investigate correlations between Kd and organic carbon, ECEC, AEC, and pH. Soil 6 is unique

225

with regard to ECEC, since the clay fraction of Soil 6 is dominated by smectite with low

226

(0.098%) organic carbon (Tables 1, S1). Soil 2, which also has low organic carbon and the

227

highest ECEC (double that of Soil 6), contains some smectite as well as pedogenic iron oxides

228

and other clay minerals. Although Soils 2 and 6 have similar organic carbon and ECEC, the

229

additional minerals and pedogenic iron oxides present in Soil 2 may interact with the zwitterionic

230

FtSaBs and cationic 6:2 FtSaAm through secondary interactions, such as sorbate-sorbate

231

interactions. Sorption of some organic cations is influenced by the location of mineral and

232

organic matter exchange sites.44 The greater complexity of the mineral phase in Soils 1-5

233

indicates the possibility of sorbate-sorbent interactions through a variety of mechanisms not

234

limited solely to electrostatic interactions, although the proportion of each sorption mechanism

235

for a given analyte needs to be determined.

236 237

Sorption was nonlinear for all soils (Table S8) for the 6:2 FtS (n = 0.8-1.2), 8:2 FtS (n = 0.74-1.1), 6:2 FtSaB (n = 0.8-1.5), 8:2 FtSaB (n = 0.41-1.8), and 6:2 FtSaAm (n = 0.17). Ranges 9 ACS Paragon Plus Environment

Environmental Science & Technology

Page 10 of 32

238

for the Kd values (Table S9) are 3.1-12 L/kg (6:2 FtS, Cwi = 110 nM), 17-120 L/kg (8:2 FtS, Cwi =

239

110 nM), 23-150 L/kg (6:2 FtSaB, Cwi = 8.8 nM), 34-400 L/kg (8:2 FtSaB, Cwi = 8.8 nM) , and

240

650 L/kg (6:2 FtSaAm, Cwi = 110 nM). The ranges of n for the anionic FtSs are consistent with

241

other batch sorption experiments for the anionic PFCAs and PFSAs.15,16,35 However, the n

242

ranges for the zwitterionic FtSaBs and the 6:2 FtSaAm are wider than the anionic FtSs, which

243

may indicate multiple sorption energies or mechanisms,40 as will be discussed below. Due to

244

the experimental conditions used, complete depletion of several analytes (< 0.18 nM) limits the

245

discussion to the behavior of 6:2 FtS, 8:2 FtS, 6:2 FtSaB, 8:2 FtSaB, and 6:2 FtSaAm (Soil 6

246

isotherm only).

247

Soil 1 Native pH (5.1) Isotherm. Log-transformed Freundlich isotherms (Eqn 2; Fig. 2) of the

248

anionic 6:2 and 8:2 FtS and the zwitterionic 6:2 and 8:2 FtSaB for Soil 1 at pH 5.1 indicates the

249

relative sorption strength of each sorbate. The values of the y-intercepts (i.e. log Kf) indicate that

250

the strongest sorbed analyte is the 8:2 FtSaB, followed by the 8:2 FtS, 6:2 FtSaB, and 6:2 FtS,

251

which is the weakest sorbed analyte. Within each class (FtS and FtSaB), sorption increases as

252

the fluorinated chain length increases. The increase in sorption with fluorinated chain length for

253

other PFASs was observed in previous sorption studies.15,16,19,20,45 The apparent increase of the

254

last 3 points in the 6:2 FtS isotherm and the last 2 points of the 6:2 FtSaB isotherm may suggest

255

an increase in secondary sorbate-sorbate interactions40,46,47 due to n > 1 for the 6:2 FtS and 6:2

256

FtSaB, which may indicate sorbate-sorbate interactions48. The last 2-3 points of the isotherms

257

were included in the analysis since the concentrations used to generate the points are

258

environmentally relevant. Moreover, tentative exclusion of the data points did not significantly

259

alter the observed trend or the quality of the correlation (Table S10). For the purposes of brevity,

260

only the isotherm for Soil 1 at the native pH (5.1) are discussed here. Isotherms for the 6:2 and

261

8:2 FtSs, 6:2 and 8:2 FtSaBs, and 6:2 FtSaAm (Soil 6 isotherm only) for Soils 2-6, Soil 1 pH 4,

262

and Soil 1 pH 7 are provided in the SI (Fig. S4-S10) and are included in the discussion below.

263

The sorption strength of each sorbate in a given soil (Soils 2-6, Soil 1 pH 4, and Soil 1 pH 7)

264

may be different from the order discussed for the Soil 1 native pH isotherm.

265

FtS, FtSaB, and 6:2 FtSaAm Sorption. Log Kd. Previous studies based on batch sorption

266

experiments with PFASs report changes in log Kd as the number of CF2 groups increase but only

267

for anionic PFASs. The log Kd increase per CF2 group between the 6:2 and 8:2 homologs for the 10 ACS Paragon Plus Environment

Page 11 of 32

Environmental Science & Technology

268

FtSs and FtSaBs was 0.41 ± 0.059 and 0.20 ± 0.088, respectively (Table S11). The increase in

269

log Kd per CF2 group for the anionic FtSs is consistent with the 0.5-1 log Kd increase for the

270

anionic PFCAs and PFSAs.15,16,18,49 The log Kd increase per CF2 group for the zwitterionic

271

FtSaBs is lower than that for FtSs, and the large 95 % CI may be partially attributed to greater

272

analytical uncertainty about FtSaB concentrations (see Analytical Methods in SI). The increase

273

in log Kd with an increase in the number of CF2 groups indicates that hydrophobic interactions

274

may be an important sorption mechanism15 for the anionic FtSs and to a lesser extent for the

275

zwitterionic FtSaBs. The lower log Kd per CF2 group for the FtSaBs indicates that a different

276

primary sorption mechanism, such as electrostatic interactions, may influence sorption more

277

heavily.

278

For a given fluorinated chain length, the 6:2 FtSaB has a larger Kd (Cwi = 110 nM) than

279

the 6:2 FtS for all soils and conditions, which is likely due to the greater size, molecular weight,

280

and type of charges associated with 6:2 FtSaB. Since the 6:2 FtSaB head group has one positive

281

charge and a terminal negative charge at pH 5.1 (Fig. 1), the positive charge within the head

282

group is contributing to increased interactions, presumably due to electrostatic interactions. The

283

6:2 FtSaAm, which was completely sorbed to all soils except Soil 6, has one terminal positive

284

charge (Fig. 1). The 6:2 FtSaAm has the highest observed Kd value (Cwi = 110 nM, Table S9), so

285

the number of positive charges cannot explain the difference in sorption. Rather, the position of

286

the charges as well as the net charge appear to be relevant. In this case, the terminal positive

287

charge on the 6:2 FtSaAm leads to greater sorption onto soil, whereas the 6:2 FtSaB, while

288

having a net neutral charge, also has a terminal negative charge, which may exert a repulsive

289

effect in close proximity to the soil surface, as was observed in the sorption of oxytetracycline

290

and ciprofloxacin50.

291

The single-point Kd (Cwi = 110 nM) values for the 6:2 FtS (3.1-12 L/kg; Table S9) are in

292

good agreement with the field-Kd values reported (5.8 L/kg23 and 3.2 L/kg26) for sediment-water

293

systems. The Kd (Cwi = 8.8 nM) values for the 6:2 FtSaB range from 23-240 L/kg (Table S9),

294

which are significantly greater than the single field-Kd of 4.5 L/kg23. The single Kd (Cwi = 110

295

nM) value obtained for the cationic 6:2 FtSaAm was 650 L/kg (Table S9), which is also

296

significantly greater than the single reported field-Kd of 34 L/kg23. The lower values reported by

297

Boiteux et al.23 may be due to incomplete extraction of zwitterionic and cationic PFASs from 11 ACS Paragon Plus Environment

Environmental Science & Technology

Page 12 of 32

298

sediment using the milder extraction conditions (1% acetic acid in methanol) compared to the 0.5

299

M HCl in methanol in the present study. Alternatively, the organic matter and ECEC properties

300

of the sediment, which were not reported, may have contributed to the lower Kd values.23

301

Correlations. Organic Carbon. The experimental data indicate that anionic 6:2 FtS (0.83, p =

302

0.039) and 8:2 FtS (0.96, p = 0.0019) correlate with organic carbon (Fig. 3, Table S12). The Kd

303

(Cwi = 110 nM) values for the longer-chained 8:2 FtS are consistently greater than those of 6:2

304

FtS except for Soil 4 (Kd = 120 L/kg), in which the 8:2 FtS Kd is disproportionately high for an

305

unknown reason. Removing the Kd values for Soil 4 from the correlation analysis, no correlation

306

exists for the 6:2 FtS (0.21, p = 0.73) or the 8:2 FtS (0.42, p = 0.48), indicating that the Soil 4 Kd

307

(Cwi = 110 nM) values are likely outliers. Log transformations of both Kd and organic carbon did

308

not improve correlations (Table S13). At the lowest levels of organic carbon (0.098 – 0.12%),

309

the Kd (Cwi = 110 nM) values for the 6:2 and 8:2 FtS are similar in magnitude to those for the

310

soils with higher organic carbon (1.0 – 2.3%), which indicates that the mineral phase in the low

311

organic carbon soils (Soils 2, 6) influences sorption.14,17 The nonpolar fluorinated tail of the

312

anionic FtSs may interact with the hydrophobic (nonpolar) nanosites51-54 between the charged

313

sites on the mineral surface55 via weak hydrophobic interactions.14-16,56

314

The lack of a correlation in FtS sorption may be due to variations in the extent of organic

315

matter decomposition of the soils tested. The relationship between C/N in soil organic matter

316

and oxygen-containing functional groups is based on the following two premises: (a) the

317

majority of terrestrial organic matter is decomposed by oxidative depolymerization,57 which adds

318

oxygen-containing functional groups to oxidized compounds,58 and (b) oxidative

319

depolymerization of faunal debris (C/N > 25) is carried out by microbiota (C/N 6-10), in which

320

“fresh” organic debris with a large C/N (i.e. 30) are slowly converted into an amorphous

321

heterogeneous organic phase (humic substances) with a small C/N (i.e. 12).59,60 If the C/N ratio is

322

accepted as a rough proxy for the extent of organic matter decomposition61 with a large C/N

323

(C/N 25) indicating a relative prevalence of aliphatic C and nonpolar functionality (i.e., relatively

324

undecomposed organic matter), the C/N ratio can be treated as a rough proxy for the

325

decomposition stage ( = the "quality" of organic matter).62 Soils 1-3 and 5 have either low

326

organic carbon or a lower C/N ratio (greater number of carboxyl groups; Table 1, Table S1),

327

indicating a minimal influence of organic carbon on sorption (Soil 2) or less hydrophobic organic 12 ACS Paragon Plus Environment

Page 13 of 32

Environmental Science & Technology

328

matter (Soils 1, 3, and 5). Therefore, the lack of correlation of FtS sorption with soil organic

329

carbon may be due to low hydrophobicity of the organic matter of the soils tested, with the

330

exception of Soil 4, which is more hydrophobic (higher C/N ratio; Tables 1 and S1) with fewer

331

carboxyl groups. Alternatively, the 6:2 and 8:2 FtS may require an organic carbon content

332

greater than 2.3% before hydrophobic interactions plays a significant role in their sorption. A

333

trend is difficult to discern without additional soils between 2.3% and 7.7% organic carbon.

334

To the best of our knowledge, studies examining PFAS sorption do not consider metrics

335

for the extent to which decaying organic matter is decorated with ionizable, oxygen containing

336

functional groups, which needs to be examined further. Many sorption studies of PFCAs and

337

PFSAs observe an increase in Kd with increasing organic carbon without any organic carbon

338

threshold,13-16 while a single study found little change in Kd with increasing organic carbon.63

339

No statistical evidence exists for correlations between the zwitterionic 6:2 FtSaB (-0.37, p

340

= 0.47) and the 8:2 FtSaB (-0.60, p = 0.40) and organic carbon (Fig. S11, Table S12), which is

341

consistent with reports that Kd values for zwitterionic pharmaceuticals do not correlate with

342

organic carbon content.36,37,64 The Kd (Cwi = 8.8 nM) values for the 8:2 FtSaB are consistently

343

and proportionally higher than the 6:2 FtSaB, due to the increased hydrophobicity of the

344

additional two CF2 groups. Relative to the anionic FtSs, the magnitude of the Kd values for the

345

zwitterionic FtSaBs are higher, which is likely due to the positive charge associated with the

346

polar head group, as will be discussed below. Cation exchange and electrostatic interactions

347

dominate,38 since electrostatic interactions are more thermodynamically favorable than

348

hydrophobic interactions65,66 or anionic ligand exchange,38 although hydrophobicity may help

349

exclude the sorbate from solution and aid in a higher extent of sorption.40 However, assessing

350

the thermodynamic favorability of the FtSaBs was outside the scope of the present study.

351

ECEC. No statistical evidence exists for correlations between the 6:2 FtS (-0.56, p = 0.25) and

352

the 8:2 FtS (-0.41, p = 0.42) and ECEC (Fig. 4a, Table S12), likely due to repulsion between

353

negatively charged organic matter and mineral surfaces and the negatively charged sulfonate

354

group. The high Kd (Cwi = 110 nM) of 120 L/kg for the 8:2 FtS in Soil 4 with an ECEC of 5.7 ±

355

0.80 meq/100 g is attributed to the more hydrophobic nature of the organic matter as discussed

356

above rather than cation exchange processes. The extent of cation bridging between Ca2+ and the

357

anionic FtSs was not assessed and is the focus of on-going research. 13 ACS Paragon Plus Environment

Environmental Science & Technology

358

Page 14 of 32

Strong statistical evidence for positive correlations exist for the zwitterionic 6:2 FtSaB

359

(0.94, p = 0.0052) and 8:2 FtSaB (0.99, p = 0.0051) and ECEC (Fig. 4b, Table S12). The

360

proportionate increase in Kd (Cwi = 8.8 nM) from the 6:2 FtSaB to the 8:2 FtSaB may arise from

361

the greater affinity of the 8:2 FtSaB to the hydrophobic nanosites in between the localized

362

negative charges on the smectite surface.55 Alternatively, the hydrophobic perfluoroalkyl moiety

363

may allow easier exclusion from aqueous solution due to solvation effects.67 The cationic 6:2

364

FtSaAm was completely depleted from the aqueous phase in all but one soil (Soil 6; Fig. 4b),

365

which has the second highest ECEC (10 ± 3.4 meq/100 g). The terminal positive charge in the

366

cationic 6:2 FtSaAm may interact more readily with the cation exchange sites than the FtSaBs, in

367

which the terminal carboxyl group of the FtSaBs may repel the negatively charged CEC sites68.

368

Similarly, sorption studies with zwitterionic and cationic veterinary pharmaceuticals,36-38,64,69

369

organic cations,44,65 and cationic hydrocarbon surfactants70 indicate that electrostatic interactions

370

dominate, and contributions from hydrophobic partitioning are almost non-existent.38,44,65,70

371

Although the strong correlations between the zwitterionic FtSaBs and ECEC and the

372

single Kd (Cwi = 110 nM) value for the cationic 6:2 FtSaAm for Soil 6 indicate that electrostatic

373

interactions heavily influence sorption of zwitterionic and cationic PFASs, other mechanisms,

374

such as hydrophobic interactions, clearly have some impact since the 8:2 FtSaB has higher Kd

375

values than the 6:2 FtSaB. Similar to pharmaceuticals and other organic cations, traditional soil

376

properties may not be adequate to predict PFAS sorption, and new Kd models, such as those

377

developed by MacKay and Vasudevan,71 Droge et. al,44 and Jolin et. al,72 need to be incorporated

378

to assess the influence of electrostatic interactions, hydrophobic interactions, surface

379

complexation, and sorbate molecular volume.

380

AEC. No statistical evidence exists for a correlation between the anionic 6:2 FtS (0.58, p = 0.23)

381

and AEC, whereas some evidence exists for a correlation between the 8:2 FtS (0.83, p = 0.031)

382

and AEC (Fig. 5). However, the 8:2 FtS Kd value for Soil 4 is believed to be an outlier as

383

discussed in the Organic Carbon section; therefore, excluding Soil 4 from the correlation, no

384

evidence exists for a correlation between the 8:2 FtS (-0.50, p = 0.39) and AEC. Analysis of the

385

Kd values using AEC/ECEC73 and log-log transformations did not improve correlations (Table

386

S12, Table S13). The sorption of the 8:2 FtS is proportionally greater than the 6:2 FtS, except in

387

Soil 4. Since Soil 4 has both the highest organic carbon and the highest AEC, the influence of 14 ACS Paragon Plus Environment

Page 15 of 32

Environmental Science & Technology

388

electrostatic interactions due to Soil 4’s positive charge and hydrophobic interactions cannot be

389

determined.

390

Anion exchange sites are fully protonated (pH ≤ 6; Fig. S13), singly coordinated

391

hydroxyl groups that arise from poorly crystalline forms of iron oxides (ferrihydrite) and

392

aluminosilicates.74 Soil 3 is a particularly oxide rich Ultisol, and Soil 4 has a poorly crystalline

393

mineral phase (“andic” soil properties) that contains singly coordinated hydroxyl groups (Table

394

1, Table S1). In the case of Soil 4 with the anionic 8:2 FtS, inner sphere complex formation via

395

anionic ligand exchange with the singly coordinated hydroxyl groups74 may contribute to the

396

observed increase in sorption. However, if contributions from inner sphere complex formation

397

strongly influenced the 8:2 FtS sorption in Soil 4, a proportional increase in the sorption of the

398

6:2 FtS would be expected. The lack of correlation between FtS sorption and AEC indicates that

399

the sulfonate group may not be as effective at surface complexation as carboxyl groups74,75 or

400

carboxyl groups with neighboring hydroxyl groups76.

401

No statistical evidence exists for correlations between the zwitterionic 6:2 FtSaB (-0.21, p

402

= 0.69) and 8:2 FtSaB (-0.58, p = 0.42) and AEC (Fig. S12). AEC trends with zwitterion

403

sorption are less frequently studied, but zwitterionic pesticide sorption experiments found either

404

an increase75 or no change77 in sorption with increasing AEC. The lack of correlation with the

405

zwitterionic FtSaBs and AEC is not unexpected because, in the case of zwitterionic

406

pharmaceutical sorption, the contribution of surface complexation and electrostatic interactions

407

with anion exchange sites has less influence than electrostatic interactions with cation exchange

408

sites.38,65,66

409

pH. As pH increases from 4 to 7 in Soil 1, Kd (Cwi = 110 nM) values remain unchanged for the

410

anionic 6:2 FtS (-0.55, p = 0.63) but decrease for the anionic 8:2 FtS (-0.99, p = 0.019; Fig. 6).

411

For the zwitterionic FtSaBs, however, Kd (Cwi = 8.8 nM) values decrease then remain constant as

412

pH increases (6:2 FtSaB: -0.81, p = 0.39; 8:2 FtSaB: -0.69, p = 0.51; Fig. 6). Due to the limited

413

statistical power with three data points, the correlations discussed should be interpreted

414

cautiously.

415 416

The decrease in Kd (Cwi = 110 nM) with increasing pH for the anionic 8:2 FtS is consistent with observed decreases in sorption for organic acids78 and other anionic PFASs16 15 ACS Paragon Plus Environment

Environmental Science & Technology

Page 16 of 32

417

with an increase in pH. The decrease is approximately 0.17 log units per unit increase in pH,

418

assuming a linear fit, which is less steep relative to other anionic PFASs.16 Since the 6:2 and 8:2

419

FtS remain anions in the pH range studied (Fig. S13), the decrease in sorption is likely due to

420

deprotonation of the negatively charged organic matter (pKa ~ 4.5; Fig. S13)79,80 and thus anion

421

repulsion. Given that the zero-point-of-charge of iron and aluminum oxides is approximately

422

8.5, the oxide surfaces are increasingly protonated with decreasing pH and become increasingly

423

available to undergo anionic ligand exchange81 and, thus, result in a higher Kd at lower pH. The initial decrease in Kd (Cwi = 8.8 nM) that was then followed by no change in Kd (Cwi

424 425

= 8.8 nM) as pH increased for the zwitterionic FtSaBs is likely not due to the speciation of the

426

FtSaBs (Fig. S13) but rather the protonation of organic matter. Between pH 4 and pH 7, the

427

FtSaBs are zwitterionic with ~99 % deprotonated carboxyl group (negative charge) and a

428

positively charged quaternary amine, indicating that speciation does not significantly change in

429

the pH range studied. Soil 1 has an ECEC of 6.8 meq/100g at pH 5.1, and a batch reactor

430

containing Soil 1 and 440 nM 6:2 FtSaB Cwi has 6.8*10-2 mmol charge and 6.7*10-6 mmol

431

positively charged PFASs, indicating that the ECEC, even with changes in pH, would not be

432

exceeded in the current system.37 Instead, the speciation of the organic matter changes. At pH 4,

433

more than 50 % of carboxylic functional groups in soil organic matter will be protonated,

434

resulting in a joint contribution of hydrophobic interactions and electrostatic interactions through

435

cation exchange sites to FtSaB sorption. As pH increases and the carboxyl groups in the organic

436

matter become deprotonated, electrostatic interactions still influence sorption, but the negatively

437

charged organic matter likely repels the terminal carboxyl group of the FtSaB, causing sorption

438

to decrease. The finding contrasts those from sorption studies of veterinary pharmaceuticals in

439

which speciation changed as a function of pH and significantly influenced zwitterion sorption.36-

440

38,77

441

IMPLICATIONS

442

The low Kd values for the anionic 6:2 FtS suggest that the 6:2 FtS is highly mobile in

443

groundwater. Analysis of AFFF-impacted groundwater12,82 indicates that the 6:2 FtS is present

444

in high concentrations (up to mg/L). The higher Kd values indicate that the anionic 8:2 FtS,

445

zwitterionic FtSaBs, and cationic 6:2 FtSaAm are more likely to be associated with soil and

446

sediment. The anionic 8:2 FtS has been found in higher concentrations on AFFF-impacted soils 16 ACS Paragon Plus Environment

Page 17 of 32

Environmental Science & Technology

447

and sediments,22,27,83 while the first reports of zwitterionic FtSaBs and cationic FtSaAms on

448

soil21 and sediment are currently being presented.22-25

449

By analogy, the anionic 8:2 FtS, zwitterionic FtSaBs, and cationic 6:2 FtSaAm are likely

450

to be found in PFAS source zones, especially where AFFFs were repeatedly applied at a field

451

site. However, current estimates of the mass of PFASs in the source zone are likely to be

452

significantly underestimated. Although the high Kd analytes may be immobilized in the source

453

zone, the complex interactions between anionic, zwitterionic, and cationic PFASs and soil may

454

impact their mobility in the subsurface. Furthermore, the high Kd values of the anionic 8:2 FtS,

455

zwitterionic FtSaBs, and the cationic 6:2 FtSaAm may not accurately predict the mobility of

456

these polyfluoroalkyl substances at all AFFF-impacted sites, as cationic PFASs have been found

457

in high abundance in AFFF-impacted groundwater.11 Mobile cationic PFASs have the potential

458

to impact drinking water sources, and non-fluorinated cations have been found to be more toxic

459

to aquatic species.84,85 Therefore, cationic PFASs might be more toxic by analogy. Removal of

460

mobile zwitterionic and cationic PFASs from drinking water sources is unknown, in part due to

461

the current analytical methods employed by the private sector, which only focus on well-studied

462

anionic PFASs (i.e. PFCAs and PFSAs).

463

Overall, the lack of correlations between the anionic FtSs, zwitterionic FtSaBs, and

464

cationic 6:2 FtSaAm and bulk soil parameters, such as organic carbon content, ECEC, and AEC,

465

indicates that the bulk parameters do not adequately predict sorption, at least for the compounds

466

studied. The influence of electrostatic interactions, hydrophobic interactions, cation bridging,

467

surface complexation, and structures of PFASs need to be understood in source zones before

468

robust remediation strategies can be proposed. For example, the multilayer sorption observed for

469

the anionic 6:2 FtS and the zwitterionic 6:2 FtSaB indicates that soil surfaces may become

470

coated in PFASs. Sorption of additional PFASs in AFFF to a soil already saturated with PFASs

471

may increase the sorption of the added PFASs, due to fluorophilic interactions between PFASs

472

sorbed to the surface and additional PFASs in solution.86 Furthermore, the impact of PFCAs and

473

PFSAs in the subsurface from AFFFs9,12 and biodegradation87-89 on the sorption of zwitterionic

474

and cationic PFASs remains unknown. Additionally, desorption and therefore the reversibility of

475

sorbed zwitterionic and cationic PFASs need to be determined, as the reversibly bound PFASs

476

may become mobile in the subsurface.20 17 ACS Paragon Plus Environment

Environmental Science & Technology

477

Notes

478

The authors declare no competing financial interest.

Page 18 of 32

479 480

ACKNOWLEDGEMENTS

481

K. Barzen-Hanson was supported by the National Science Foundation’s Graduate Research

482

Fellowship Program Fellowship 1314109-DGE. The study was supported by the Strategic

483

Environmental Research and Defense Program Grant ER-2128 (J. Field). The authors would like

484

to thank Nicole Riddell and Alan McAlees of Wellington Laboratories, Inc. for providing the

485

pKa estimates and rationale, Steven Droge for suggesting Chemicalize for pKa values, and

486

Christopher Higgins of Colorado School of Mines for the insightful comments in the preparation

487

of this manuscript.

488 489

SUPPORTING INFORMATION AVAILABLE

490

Chemicals, details on isotherm set-up, absolute extraction efficiencies, soil extraction method

491

validation, analytical methods, pKa rationale, Tables S1-S13, Figures S1-S13. This information

492

is available free of charge via the Internet at http://pubs.acs.org.

493 494 495 496 497 498 499 500

18 ACS Paragon Plus Environment

Page 19 of 32

501

Environmental Science & Technology

TOC Art

502

19 ACS Paragon Plus Environment

Environmental Science & Technology

503

Page 20 of 32

Table 1. Soil properties. a

b

%N

C/N Ratio

CECc (meq/100g)

ECECd (meq/100g)

AECe (meq/100g)

% Clay

% Sand

% Silt

b

Soil #

pH

% OC

1

5.1

1.5

0.13

13

14 ± 0.59f

6.8 ± 0.68

0.20

22

6.3

71

2

5.5

0.12

0.02

6.8

22 ± 4.2

17 ± 2.2

0.58

26

10

64

3

5.1

2.3

0.20

13

17 ± 3.1

5.1 ± 0.56

1.2

48

14

39

4

5.0

7.7

0.43

21

36 ± 3.6

5.7 ± 0.80

2.2

18

37

45

5

5.0

1.0 ± 0.19

0.084 ± 0.0087

12 ± 1.1

16 ± 1.6

7.5 ± 0.44

0.28g

23 ± 3.2

4.8 ± 0.29

72 ± 3.0

6

5.2

0.098

0.004

30

16 ± 1.5

10 ± 3.4

0.33

24

3.6

73

504 505 506 507 508 509

a

pH at which the isotherm was conducted. bPercent organic carbon (% OC) and percent nitrogen, as determined by the method of Goni et al.90 cCation Exchange Capacity, measured by summation method, pH 7. dEffective cation exchange capacity measured at the native soil pH, as determined by the method of Gillman and Sumpter.91,92 eAnion exchange capacity at native soil pH (using water). fError computed as the 95% CI determined from a blind triplicate analysis. gOnly two values were valid, which has limited statistical power. No 95% CI was calculated.

20 ACS Paragon Plus Environment

Page 21 of 32

Environmental Science & Technology

510 511

Figure 1. Structures of the dominant species of (A) the FtSs, (B) the FtSaBs, and (C) the 6:2

512

FtSaAm in National Foam AFFF at all native soil pHs.

513

21 ACS Paragon Plus Environment

Environmental Science & Technology

Page 22 of 32

514 515

Figure 2. Log-transformed Freundlich isotherms for the anionic 6:2 and 8:2 FtSs and the

516

zwitterionic 6:2 and 8:2 FtSaBs for the Soil 1 native pH isotherm. The ovals highlight the sharp

517

increase in sorption.

518

22 ACS Paragon Plus Environment

Page 23 of 32

Environmental Science & Technology

519 520

Figure 3. A lack of correlation for the anionic FtSs as a function of soil organic carbon. Error

521

bars indicate the 95% CI.

522

23 ACS Paragon Plus Environment

Environmental Science & Technology

Page 24 of 32

523 524

Figure 4. A lack of correlation for (A) the anionic FtSs and (B) strong, positive correlations for

525

the zwitterionic 6:2 and 8:2 FtSaBs and the cationic 6:2 FtSaAm with increasing ECEC. Error

526

bars represent the 95% CI. The aqueous phase concentration was