Subscriber access provided by University of Florida | Smathers Libraries
Article
Synthesis of Ag3PO4 Crystals with Tunable Shapes for Facet-Dependent Optical Property, Photocatalytic Activity and Electrical Conductivity Examinations Meng-Shan Hsieh, Huang-Jen Su, Pei-Lun Hsieh, Yun-Wei Chiang, and Michael H. Huang ACS Appl. Mater. Interfaces, Just Accepted Manuscript • DOI: 10.1021/acsami.7b13941 • Publication Date (Web): 18 Oct 2017 Downloaded from http://pubs.acs.org on October 21, 2017
Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.
ACS Applied Materials & Interfaces is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.
Page 1 of 35
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Applied Materials & Interfaces
Synthesis of Ag3PO4 Crystals with Tunable Shapes for Facet-Dependent Optical Property, Photocatalytic Activity and Electrical Conductivity Examinations
Meng-Shan Hsieh,† Huang-Jen Su,‡ Pei-Lun Hsieh,§ Yun-Wei Chiang,† and Michael H. Huang*,†
†
Department of Chemistry, ‡Interdisciplinary Program of Sciences, and §Department
of Materials Science and Engineering, National Tsing Hua University, Hsinchu 30013, Taiwan
ABSTRACT:
This work has developed conditions for the synthesis of Ag3PO4
cubes, rhombic dodecahedra, {100}-truncated rhombic dodecahedra, tetrahedra, and tetrapods by tuning the amount of NH4NO3, NaOH, AgNO3, and K2HPO4 solutions added.
Use of a lesser amount of AgNO3 solution can form much smaller rhombic
dodecahedra and tetrahedra.
Sub-micrometer-sized Ag3PO4 cubes and rhombic
dodecahedra with sizes larger than 300 nm do not exhibit optical size effect, but ~290 nm rhombic dodecahedra show a smaller band gap value than that for larger cubes, and tetrahedra show the most blue-shifted absorption edge. present in Ag3PO4 crystals.
Optical facet effect is
Ag3PO4 cubes are more photocatalytically active than 1
ACS Paragon Plus Environment
ACS Applied Materials & Interfaces
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 2 of 35
rhombic dodecahedra toward photodegradation of methyl orange, but tetrahedra are inactive, showing clear presence of photocatalytic facet effects.
Electron
paramagnetic resonance (EPR) results confirm much higher production of hydroxyl radicals from photoirradiated Ag3PO4 cubes than from rhombic dodecahedra, while tetrahedra yield essentially no radicals.
A modified band diagram showing different
degrees of band edge bending can explain these observations.
All these Ag3PO4
crystals show poor electrical conductivity properties, but the {110} faces are slightly more conductive than the {100} faces.
As a result, current rectifying I‒V curves
have been obtained, demonstrating facet-dependent electrical properties are broadly observable in many semiconductor materials.
This work reveals again that
facet-dependent optical, photocatalytic, and electrical conductivity properties are intrinsic semiconductor properties.
KEYWORDS:
electrical conductivity, facet-dependent properties, photocatalytic
activity, semiconductor, silver phosphaste
INTRODUCTION
Recent demonstrations of facet-dependent photocatalytic,1‒8 electrical 2
ACS Paragon Plus Environment
Page 3 of 35
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Applied Materials & Interfaces
conductivity,9‒14 and light absorption properties of Cu2O, Ag2O, PbS, TiO2 crystals and other nanostructures have shown that control of crystal surfaces and interfaces are highly important to fully understand semiconductor properties.15‒20 transmission can have facet effect.19,20
Even heat
The general idea is that there exists an
ultrathin surface layer with different degrees of surface band bending for various crystal faces giving rise to these interesting phenomena.1‒3,9‒11
This layer affects
how charge carriers, photons, and heat enter and exit the semiconductor crystals. For example, Cu2O rhombic dodecahedra are appreciably more photocatalytically active than octahedra, while cubes are inactive.1‒3
Ag2O and Cu2O octahedra are
much more electrically conductive than their cubic crystals, but their {110}-bound rhombic dodecahedra are simply not conductive.9,10
To show these properties are
generally observable in many semiconductors, it is necessary to examine other materials such as silver phosphate crystals.
Ag3PO4 is an excellent choice to extend
facet effect examinations because their various crystal morphologies with sharp faces have been synthesized.21‒27
For example, {110}-bound Ag3PO4 rhombic
dodecahedra can be synthesized by mixing silver acetate and Na2HPO4 solutions, while {100}-bound cubes have been prepared by mixing AgNO3, NH3, and Na2HPO4 solutions.21
Ag3PO4 tetrahedra exposing {111} facets can be obtained by reacting
3
ACS Paragon Plus Environment
ACS Applied Materials & Interfaces
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 4 of 35
silver nitrate with H3PO4 in ethanol solution.22 In another report, the chemicals and temperature used to make Ag3PO4 crystals with these shapes are also not consistent.24 It is desirable to develop synthetic conditions to grow Ag3PO4 crystals with tunable shapes using the same reagents.
With successful synthesis of Ag3PO4 cubes,
tetrahedra, and rhombic dodecahedra, their facet-dependent photocatalytic activity and electrical conductivity properties can be examined.
Electrical conductivity
measurements have not been performed on single Ag3PO4 crystals.
In this study, we have developed aqueous synthetic conditions to make Ag3PO4 cubes, rhombic dodecahedra, {100}-truncated rhombic dodecahedra, tetrahedra, and tetrapods using the same reagents in the absence of any capping agent.
Some level
of size tunability has been achieved to evaluate crystal size and facet factors on their band gap values.
Use of the Ag3PO4 crystals for the photodegradation of methyl
orange reveals moderate performance for cubes and rhombic dodecahedra but shows surprisingly photocatalytic inactivity for tetrahedra.
In the literature, all Ag3PO4
particle shapes have been reported to exhibit good to excellent photocatalytic properties.21‒26
Electron paramagnetic resonance (EPR) spectra were taken to
confirm the photocatalysis results. observations have been considered.
Possible explanations for these contradictory Electrical conductivity measurements have been 4
ACS Paragon Plus Environment
Page 5 of 35
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Applied Materials & Interfaces
performed on single Ag3PO4 particles exposing different crystal faces for the first time. Although all crystal facets are poorly conductive, a slightly current rectifying effect has been recorded with electrodes making contacts to the {100} and {110} facets of a truncated rhombic dodecahedron.
EXPERIMENTAL SECTION
Chemicals.
Ammonium nitrate (NH4NO3, 99%, Showa), silver nitrate (AgNO3,
99.8%, Sigma-Aldrich), sodium hydroxide (NaOH, 99%, Sigma-Aldrich), potassium hydrogen phosphate (K2HPO4, Hayashi Pure Chemical), ethanol (EtOH, 99.8%, Sigma-Aldrich), methyl orange (C14H14N3NaO3S, Hayashi Pure Chemical), and spin trapping reagent DMPO (5,5-dimethyl-1-pyrroline N-oxide, ≥ 97%, Sigma-Aldrich) were used without further purification. Ultrapure distilled and deionized water (18.2 MΩ) was used for all solution preparations.
Synthesis of Ag3PO4 Crystals with Tunable Shapes. synthesized with room light turned off.
All Ag3PO4 crystals were
To make Ag3PO4 cubes, rhombic
dodecahedra, and {100}-truncated rhombic dodecahedra, tetrahedra, and tetrapods, 8.92, 8.42, 8.12, 1.8874 and 1.8874 mL of deionized water were added to respective 5
ACS Paragon Plus Environment
ACS Applied Materials & Interfaces
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 6 of 35
vials, and then 100, 600, 600, 218.8, and 281.3 µL of 0.4 M NH4NO3 solution were respectively introduced.
Next, 180, 180, 180, 393.8, and 506.3 µL of 0.2 M NaOH
solution and 400, 400, 550, 500, and 500 µL of 0.05 M AgNO3 solution were added to the respective vials.
The solutions were stirred vigorously for 10 min to complete
the formation of [Ag(NH3)2]+ complex.
Finally, 400, 400, 550 µL of 0.1 M K2HPO4
solution were added to grow Ag3PO4 cubes, rhombic dodecahedra, and {100}-truncated rhombic dodecahedra, and the solution color turned from colorless to light yellow.
To form Ag3PO4 tetrahedra and tetrapods, 7.0 mL of 0.7 M K2HPO4
solution was introduced to each vial. growth.
The solutions were stirred for 2 min for crystal
Scheme S1 and Table S1 in the Supporting Information provide the
synthetic process and the exact reagent amounts used. centrifuged at 7500 rpm for 5 min.
The solutions were then
The top solution containing unreacted chemicals
was carefully removed, and the Ag3PO4 precipitate was dispersed in deionized water and 95% ethanol with 1:1 volume ratio and centrifuged twice more.
Finally, the
Ag3PO4 particles were kept in 99.8% ethanol for subsequent characterization and photocatalysis experiments.
To prepare smaller Ag3PO4 rhombic dodecahedra and tetrahedra, the volumes of 0.4 M NH4NO3, 0.2 M NaOH and 0.1 or 0.7 M K2HPO4 solutions are the same as 6
ACS Paragon Plus Environment
Page 7 of 35
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Applied Materials & Interfaces
those used to make regular-sized Ag3PO4 rhombic dodecahedra and tetrahedral, but the volume of 0.05 M AgNO3 solution added was decreased to 325 µL for both shapes. Precipitate was not observed after adding the K2HPO4 solution.
Again stirring for 10
min before K2HPO4 introduction and 2 min after K2HPO4 addition was required. Next, the solution was poured into a centrifuge tube with 5 mL of 95% ethanol.
The
solution turned light yellow gradually, indicating the formation of Ag3PO4 crystals. After 2 min, the same washing process followed as depicted above.
See Scheme S2
and Table S2 for the reaction procedure and the exact reagent amounts used.
Photocatalytic Experiments.
The synthesized Ag3PO4 particles were dried,
weighted, and dispersed in deionized water with a concentration of 1 mg/mL.
For
Ag3PO4 cubes, rhombic dodecahedra, and tetrahedra, 2.45, 1.77, and 1.22 mL of the solutions having the same total particle surface area (0.029 m2) were respective added to a cubic quartz vial. Then methyl orange (MO) in deionized water was added to the vial with a final concentration of 15 ppm and a total solution volume of 12 mL. Before light illumination, the solution was stirred continuously in the dark for 30 min for molecular adsorption equilibrium. 500-W Xenon lamp placed 30 cm away.
Then the solution was illuminated by a The average light intensity reaching to the
solution was 436 mW/cm2 measured using a power meter. 7
ACS Paragon Plus Environment
A filter blocking light
ACS Applied Materials & Interfaces
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 8 of 35
wavelengths below 400 nm was placed between the vial and Xenon lamp to reduce Ag3PO4 absorption.
An aliquot of 800 µL was withdrawn from the solution at
regular time intervals and centrifuged immediately at 6500 rpm for 2 min to remove the Ag3PO4 particles for spectral measurements.
Instrumentation.
Scanning electron microscopy (SEM) images were taken
using a JEOL JSM-7000F scanning electron microscope.
X-ray diffraction (XRD)
patterns were collected using a Bruker D2 PHASER desktop diffractometer with Cu Kα radiation.
UV–vis diffuse reflectance spectra were obtained by a JASCO V-570
spectrophotometer equipped with a solid sample holder.
A X500 Xenon lamp from
Blue Sky Technologies was used as light source in photocatalysis.
EPR spectra were
collected at ambient temperature on a Bruker ELEXSYS E580-400 EPR spectrometer.
RESULTS AND DISCUSSION
Precipitation reaction proceeds instantly.
From what has been learned in the
synthesis of Ag2O crystals with systematic shape evolution, formation of [Ag(NH3)2]+ complex can slow down the precipitation reaction to yield crystals with morphology
8
ACS Paragon Plus Environment
Page 9 of 35
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Applied Materials & Interfaces
control.28 crystals.
The same synthetic strategy has been employed here to make Ag3PO4 The following reactions are involved.
3 Ag+ + PO43‒ ⇌ Ag3PO4
(1)
NH4NO3 + NaOH → NH3 + H2O + Na+ + NO3‒
(2)
AgNO3 + 2 NH3 ⇌ [Ag(NH3)2]+ + NO3‒
(3)
3 [Ag(NH3)2]+ + 6 K2HPO4 ⇌ Ag3PO4 + 6 NH4+ + 5 PO43‒ + 12 K+
(4)
Equation (1) has an equilibrium constant K of 5.56 × 1017 (inverse of Ksp of Ag3PO4 at 1.8 × 10‒18) for the formation of Ag3PO4 by directly mixing AgNO3 and a soluble phosphate source.
Equations (3) and (4) can be considered to have an overall
equilibrium constant K of 3.27 × 1010 (1/(Kf of [Ag(NH3)2]+ at 1.7 × 107) (Ksp of Ag3PO4)), recognizing the proton on HPO42‒ and the dissociated PO43‒ complicates the calculation.
Formation of [Ag(NH3)2]+ complex before reaction with phosphate
can significantly reduce the driving force toward Ag3PO4 production, allowing better shape control of the resulting crystals.
To make Ag3PO4 cubes, an almost equimolar NH4NO3 and NaOH mixture was first prepared to give the ammonia solution, and then AgNO3 solution was added to
9
ACS Paragon Plus Environment
ACS Applied Materials & Interfaces
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
form the [Ag(NH3)2]+ complex.
Page 10 of 35
Next, a K2HPO4 solution was introduced. Molar
ratios of NH4NO3:NaOH:AgNO3:K2HPO4 are 2:1.8:1:2.
To form Ag3PO4 rhombic
dodecahedra, {100}-truncated rhombic dodecahedra, tetrahedra and tetrapods, the molar ratios of NH4NO3 and AgNO3 were adjusted to tune the crystal growth rate. For example, a molar ratio of NH4NO3:AgNO3 at 6:1 yields rhombic dodecahedra; an excess amount of NH4+ ions favors the reverse reaction and lower the reaction rate. Using molar ratios of NH4NO3:AgNO3:K2HPO4 at 3.5:1:196 and 4.5:1:196, Ag3PO4 tetrahedra and tetrapods can be synthesized.
Figure 1 shows SEM images of the synthesized Ag3PO4 cubes, rhombic dodecahedra, {100}-truncated rhombic dodecahedra, tetrahedral, and tetrapods. the samples are highly uniform in size and shape, and appear to have sharp faces.
All A
{100}-truncated rhombic dodecahedron has 6 square {100} facets and 12 hexagonal {110} facets.
The tetrahedra have a somewhat curved contour because of their tips
are shorter than those in a perfect tetrahedron. be expose mostly {111} faces.22,24
The tetrahedra and tetrapods should
Figure S1 and Table S3 give the size distribution
histograms, average sizes, and standard deviations of these Ag3PO4 crystals.
In
particular, the rhombic dodecahedra have an average opposite face distance of 1057 nm, while the cubes and tetrahedra have respective average edge lengths of 534 and 10
ACS Paragon Plus Environment
Page 11 of 35
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Applied Materials & Interfaces
1283 nm.
XRD patterns of these Ag3PO4 crystals are displayed in Figure 2.
All
samples give XRD patterns well matched to the standard pattern of Ag3PO4. Because of their large dimensions and random orientations, enhanced peak intensities reflecting the exposed surface facets are less pronounced.
Nevertheless, the rhombic
dodecahedra and {100}-truncated rhombic dodecahedra show a very strong (110) reflection peak.
Similarly, the Ag3PO4 cubes exhibit an enhanced (200) peak.
The
(111) peak of tetrahedra and tetrapods are not particularly enhanced, but the tetrapods do show strong (222) peak compared to the (111) and (200) peaks.
Similar (222)
peak intensity has been observed for Ag3PO4 tetrahedra.22
Crystal morphology control is generally related to the particle growth rate and is observable from the solution color changes.5
For this reason, images of the reaction
mixture was taken from the instant K2HPO4 solution was added.
Figure S2 offers
photographs at selected time points in the growth of Ag3PO4 cubes, rhombic dodecahedra, and tetrapods.
The initially colorless solutions in the growth of cubes
and tetrapods changed to light yellow in just 1 and 10 sec, respectively.
Clearly
cubes are produced at the fastest rate, and the solution color remains unchanged after just 4 sec of reaction.
Tetrapods take about 20 sec to complete crystal growth.
Ag3PO4 rhombic dodecahedra took 30 sec to develop slightly yellow tint and 60 sec to 11
ACS Paragon Plus Environment
ACS Applied Materials & Interfaces
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 12 of 35
complete crystal growth, so they have the slowest growth rate among these particle shapes.
Because the synthesized Ag3PO4 crystals are microcrystals except the cubes, attempts have been made to reduce the dimensions of rhombic dodecahedra and tetrahedra.
We found reducing the amount of AgNO3 introduced and adding 7.5 mL
of ethanol in the last step is effective.
Since ethanol was added 2 min after the
introduction of K2HPO4 solution, complete crystal growth can be longer than 2 min for ethanol to play a role.
The initially clear solution gradually turned yellow upon
ethanol introduction, signifying precipitate formation.
Figure 3 gives SEM images
of the synthesized smaller Ag3PO4 rhombic dodecahedra and tetrahedra.
They have
sharp faces and perfect shapes necessary for facet-dependent property examinations. Figure S3 provides their size distribution histograms. standard deviations are listed in Table S4.
Average crystal sizes and their
The rhombic dodecahedra have an
average opposite face distance of 417 nm, while tetrahedra have an average edge length of 648 nm.
Recently it has shown that the light absorption positions of Cu2O nanocrystals are both size- and facet-dependent by taking UV-vis absorption spectra of size-tunable Cu2O cubes below 100 nm and octahedra smaller than 200 nm.18 12
ACS Paragon Plus Environment
As particle size
Page 13 of 35
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Applied Materials & Interfaces
increases, the absorption band red-shifts steadily.
The absorption edge of 600 nm
Ag3PO4 rhombic dodecahedra have been shown to red-shift by 30 nm than that of similarly-sized Ag3PO4 cubes.21
To further evaluate size and facet effects to the
optical properties of Ag3PO4 crystals, cubes with tunable edge lengths of 365, 462, 530, and 648 nm, as well as rhombic dodecahedra with sizes of 289, 643, 993, and 1314 nm, were synthesized.
Table S5 lists their synthetic conditions.
Figure S4
presents SEM images, diffuse reflectance spectra, and Tauc plots of the size-tunable Ag3PO4 cubes for the determination of their indirect optical band gaps.
The cube
solutions all have a greenish color. Because of their similar absorption edge, the cubes have indirect band gaps of 2.33 (365 and 462 nm cubes), 2.36 (530 nm cubes), and 2.37 eV (648 nm cubes).
It is possible that for fairly large Ag3PO4 cubes beyond
300 nm, optical size effect is not observable. size-tunable rhombic dodecahedra.
Figure S5 gives SEM images of the
All samples show a yellow solution color except
the 289 nm rhombic dodecahedra with a greenish yellow hue.
The UV‒vis diffuse
reflectance spectra of Ag3PO4 rhombic dodecahedra and their Tauc plots are available in Figure 4.
The 289 nm rhombic dodecahedra have a band gap of 2.25 eV, while
the larger rhombic dodecahedra have a band gap of 2.34‒2.35 eV.
It is unclear why
the smaller 289 nm rhombic dodecahedra yield a lower band gap value. Again
13
ACS Paragon Plus Environment
ACS Applied Materials & Interfaces
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 14 of 35
optical size effect is not observable, suggesting much smaller Ag3PO4 nanocrystals are needed to better evaluate their optical properties.
Figures S4 and S5 also express
these Ag3PO4 cubes and rhombic dodecahedra in terms of their volumes for better comparison of the crystal sizes.
For large cubes and rhombic dodecahedra, they
have very similar band gap values.
Previously these two particle shapes have also
exhibited the same absorption edge.24
Figure S6 offers SEM image, the solution
color, diffuse reflectance spectrum, and the corresponding Tauc plot for Ag3PO4 tetrahedra having an average edge length of 673 nm (volume of 3.6 × 107 nm3). solution has a greenish yellow color. is 2.38 eV (or 521 nm).
The
The determined band gap for these tetrahedra
Comparing the 289 nm rhombic dodecahedra (volume of
1.7 × 107 nm3) having a band gap of 2.25 eV (or 551 nm) to larger 365 nm cubes (volume of 4.8 × 107 nm3) with a band gap of 2.33 eV and that of 673 nm tetrahedra, rhombic dodecahedra show a more red-shifted light absorption edge, while tetrahedra display the most blue-shifted absorption edge (Figure S6d).
For these particles with
similar sizes, their absorption edges differ by 30 nm (Figure S6e), showing optical facet effects should be present even for such large Ag3PO4 crystals.
Previously
Ag3PO4 tetrahedra have also been shown to give a slightly large band gap than cubes and rhombic dodecahedra, although the sizes of these particle shapes are quite
14
ACS Paragon Plus Environment
Page 15 of 35
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Applied Materials & Interfaces
different.24
The facet-dependent photocatalytic activities of Ag3PO4 crystals have been investigated using 512 nm cubes, 371 nm rhombic dodecahedra, and 625 nm tetrahedra as the photocatalysts.
Due to the fast crystal growth rates, actual particle
sizes must be determined even though the same synthetic conditions have been followed. study.
Figure S7 shows SEM images of the crystals used for the photocatalysis
For photocatalytic activity comparison, the total particle surface area was
fixed at 0.00245 m2.
From their surface areas and volumes (see Figure S8), the
weight of a single particle can be obtained from the density of Ag3PO4 (6.37 g/cm3). The ratios of surface area per unit mass for the cube, rhombic dodecahedron, and tetrahedron are 1:1.38:2.01, so 2.45, 1.77, and 1.22 mg of Ag3PO4 cubes, rhombic dodecahedra, and tetrahedra were used.
Figure S9 offers UV‒vis absorption spectra
of methyl orange (MO) as a function of irradiation time in the presence of Ag3PO4 cubes, rhombic dodecahedra, and tetrahedra. summarized in Figure 5.
The photocatalysis results are
Before illumination, the solution was stirred for 30 min in
the dark to establish molecular adsorption equilibrium.
After illumination, the MO
absorption band centered at 463 nm shows different photodegradation efficiencies for these particle morphologies, although all of them are not good photocatalysts. 15
ACS Paragon Plus Environment
The
ACS Applied Materials & Interfaces
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 16 of 35
Ag3PO4 cubes are most photocatalytically active; MO absorption dropped 34% after 90 min of light irradiation.
The extent of MO photodecomposition is only 17% in
the presence of rhombic dodecahedra.
Surprisingly, the Ag3PO4 tetrahedra are
completely inactive after 90 min of reaction.
Strongly facet-dependent
photocatalytic activity of Ag3PO4 crystals has been observed.
Interestingly, in
addition to photocatalytic inactivity of Cu2O {100} faces, the {111} faces of Ag3PO4 crystals are also lacks photocatalytic activity.
However, literature reports have
shown all Ag3PO4 morphologies to be good photocatalysts, and the tetrahedral crystals are more photocatalytically active than rhombic dodecahedra and cubes.23,24 Our observed trend is exactly opposite of what have been reported before, although one report has shown that Ag3PO4 tetrahedra are less photocatalytically active than aggregated Ag3PO4 nanoparticles.29
To verify our photocatalysis results, EPR spectra detecting the formation of hydroxyl and other radicals were collected.
Hydroxyl radicals added to DMPO, a
spin trapping agent, form DMPOX with characteristic EPR hyperfine coupling constants.30
Purified DMPO was added to a solution containing Ag3PO4 crystals and
MO molecules for 5 min of photocatalysis experiment, and the solution was immediately sent for EPR measurements.
Figure S10 shows SEM images of the 16
ACS Paragon Plus Environment
Page 17 of 35
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Applied Materials & Interfaces
various Ag3PO4 crystals for EPR characterization. obtained.
Figure 6 is the EPR spectra
The purified DMPO without adding Ag3PO4 crystals gave no EPR signals.
Ag3PO4 cubes indeed showed the strongest EPR peaks.
The spectrum matches
exactly with theoretical parameters of DMPOX (AN = 7.2 G, Aβ-2H = 4.0 G, and g = 2.0062).
The analysis indicates the photogenerated radicals are essentially ·OH
radicals.
Ag3PO4 rhombic dodecahedra showed the same EPR profile, but the peak
intensities are much lower.
Remarkably, tetrahedra gave essentially no EPR signals,
meaning no radicals are produced from the {111} faces of Ag3PO4 crystals upon photoexcitation.
This happens presumably because no photoexcited electrons and
holes reach the {111} faces of Ag3PO4 to react with water or dissolved oxygen forming radical species.
The EPR data confirm our photocatalysis results.
The
question remains why various Ag3PO4 morphologies have been reported to show good photocatalytic properties. We suspect possible formation of a tiny amount of Ag nanoparticles during the course of photodegradation experiment.
Metal
nanoparticles and other conductive materials have been inadvertently or intentionally introduced to Ag3PO4 crystals to enhance photogenerated charge separation for improved photocatalytic performance.30,31
The morphologies of our Ag3PO4 crystals
are maintained after the photocatalysis experiment (Figure S7), although some small
17
ACS Paragon Plus Environment
ACS Applied Materials & Interfaces
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
nanoparticles can be seen on the surfaces of cubes and rhombic dodecahedra.
Page 18 of 35
XRD
patterns of the most active Ag3PO4 cubes before and after the photodegradation experiment are shown in Figure S11.
Only Ag3PO4 peaks are present, showing no
metallic Ag particles have been formed.
This outcome makes sense, because
formation of Ag nanoparticles during photoirradiation should greatly enhance photocatalytic activity of the cubes, but this is not the case.
Similarly, any formation
of Ag through surface etching would make Ag3PO4 tetrahedra photocatalytically active. We also consider MO concentrations versus catalyst concentrations in our and other studies (8 ppm MO and 2 mg/mL catalyst; 10 ppm methylene blue and 0.13 mg/mL catalyst).21,24
In our case, MO and catalyst concentrations are 15 ppm and
0.1‒0.2 mg/mL, respectively. transmit only visible light.23
Light source is all Xe lamps with a filter placed to These differences cannot explain the observed
photocatalytic inactivity of Ag3PO4 tetrahedra. One thing worthy to mention is that our Ag3PO4 crystals were synthesized in a dark room to minimize the possibility of any Ag formation, while such precautionary measure was not followed in other studies.
On the basis of the observed facet-dependent photocatalytic results, an adjusted band diagram of Ag3PO4 is constructed (Figure 7).
A similar band diagram for Cu2O
18
ACS Paragon Plus Environment
Page 19 of 35
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Applied Materials & Interfaces
has been presented to explain its facet effects on photocatalytic activity.2
The {111}
surface is drawn to bend up most steeply and deviate from the normal valence and conduction band positions to indicate the highest barrier for electron transport to the crystal surface.
The photoexcited electrons then combine with holes resulting in
photocatalytic inactivity of Ag3PO4 tetrahedra. The {100} surface is drawn to have the least degree of upward bending to represent its best electron transfer to surface-adsorbed water or oxygen for more efficient production of hydroxyl radicals. Upward bending for the {110} face should be higher than that for the {100} face to signify less efficient photoexcited electron transport to the crystal surface for radical generation.
Figure 7b‒d show the three cases of photocatalytic process for Ag3PO4
crystals.
We next probed electrical conductivity properties of a single Ag3PO4 cube, rhombic dodecahedron, and tetrahedron.
Figure 8 shows SEM images of two
tungsten probes making contacts to a single Ag3PO4 crystal and the obtained I‒V curves.
Additional I‒V curves for each particle shape are available in Figure S12.
The asymmetrical I‒V curves should be attributed to unequal contact areas of the tungsten probes.
Previous electrical conductivity measurements on polyhedral Cu2O,
Ag2O, PbS, and TiO2 crystals have recorded current in the nA to µA range.9‒13 19
ACS Paragon Plus Environment
ACS Applied Materials & Interfaces
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
However, ultrasmall current (pA) has consistently been measured for Ag3PO4 crystals, showing Ag3PO4 is poorly conductive.
This poor electrical conductivity property
may arise from the large energy band gaps for bulk and the different surfaces of Ag3PO4.24 Despite the poor conductivity behaviors and current variations from one measurement to another, the {110} faces of a rhombic dodecahedron are generally more conductive than the {100} faces of a cube. The fact the bigger rhombic dodecahedron is still more conductive than the much smaller cube also supports better electrical conductivity for the {110} faces of Ag3PO4.
To further test this slight
conductivity difference, I‒V measurements were performed on a {100}-truncated rhombic dodecahedron with tungsten probes contacting simultaneously its {100} and {110} facets (Figure 8e and Figure S12d).
Current rectifying effect has been
recorded with higher current flowing in the direction of {110} to {100}, suggesting Ag3PO4 crystals also possess facet-dependent electrical conductivity properties.
CONCLUSIONS
In this study, Ag3PO4 cubes, rhombic dodecahedra, {100}-truncated rhombic dodecahedra, tetrahedra, and tetrapods have been synthesized by tuning the amounts
20
ACS Paragon Plus Environment
Page 20 of 35
Page 21 of 35
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Applied Materials & Interfaces
of NH4NO3, NaOH, AgNO3, and K2HPO4 aqueous solutions added. cubes, all other particles are micro-crystals. tetrahedra have also been prepared.
Other than the
Much smaller rhombic dodecahedra and
Optical size effect is not observable for Ag3PO4
cubes and rhombic dodecahedra with sizes greater than 300 nm.
The smallest 289
nm rhombic dodecahedra show a more red-shifted absorption edge than that for larger cubes, while similarly-sized tetrahedra display the most blue-shifted absorption edge, so optical absorption of Ag3PO4 crystals also exhibits facet effect.
Ag3PO4 cubes are
more photocatalytically active than rhombic dodecahedra toward MO degradation, while tetrahedra display no photocatalytic activity.
EPR measurements detecting
photogenerated radicals agree well with photocatalysis results.
A modified band
diagram has been presented to explain the observed photocatalytic properties.
All
particle shapes are poorly electrically conductive, but the {110} faces are generally more conductive than the {100} faces.
Hence, slight electrical facet effects should
still be present in Ag3PO4 crystals, showing facet-dependent electrical conductivity properties are broadly observable in many semiconductor materials.
ASSOCIATED CONTENT
21
ACS Paragon Plus Environment
ACS Applied Materials & Interfaces
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Supporting Information
This Supporting Information is available free of charge via the Internet on the ACS Publications website at DOI:
Additional experimental procedures, particle size distribution histograms, photographs showing solution color changes during crystal synthesis, SEM images of Ag3PO4 cubes and rhombic dodecahedra with tunable sizes and diffuse reflectance spectra of the cubes, SEM images of Ag3PO4 crystals after the photocatalysis experiment, UV‒vis spectra, XRD patterns, and additional I‒V curves.
AUTHOR INFORMATION
Corresponding Author
*E-mail:
[email protected].
ORCID
Michael H. Huang: 0000-0002-5648-4345
Notes
22
ACS Paragon Plus Environment
Page 22 of 35
Page 23 of 35
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Applied Materials & Interfaces
The authors declare no competing financial interest.
ACKNOWLEDGMENTS
We thank the Ministry of Science and Technology of Taiwan for support of this research (MOST 104-2119-M-007-013-MY3 and 105-2633-M-007-003).
REFERENCES
(1) Yuan, G.-Z.; Hsia, C.-F.; Lin, Z.-W.; Chiang, C.; Chiang, Y.-W.; Huang, M. H. Highly Facet-Dependent Photocatalytic Properties of Cu2O Crystals Established through the Formation of Au-Decorated Cu2O Heterostructures. Chem.‒Eur. J. 2016, 22, 12548‒12556.
(2) Chu, C.-Y.; Huang, M. H. Facet-Dependent Photocatalytic Properties of Cu2O Crystals Probed by Electron, Hole and Radical Scavengers. J. Mater. Chem. A 2017, 5, 15116‒15123.
(3) Wu, S.-C.; Tan, C.-S.; Huang, M. H. Strong Facet Effects on Interfacial Charge Transfer Revealed through the Examination of Photocatalytic Activities of 23
ACS Paragon Plus Environment
ACS Applied Materials & Interfaces
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Various Cu2O‒ZnO Heterostructures. Adv. Funct. Mater. 2017, 27, 1604635.
(4) Su, Y.; Li, H.; Ma, H.; Robertson, J.; Nathan, A. Controlling Surface Termination and Facet Orientation in Cu2O Nanoparticles for High Photocatalytic Activity: A Combined Experimental and Density Functional Theory Study. ACS Appl. Mater. Interfaces, 2017, 9, 8100‒8106.
(5) Chen, Y.-J.; Chiang, Y.-W.; Huang, M. H. Synthesis of Diverse Ag2O Crystals and Their Facet-Dependent Photocatalytic Activity Examination. ACS Appl. Mater. Interfaces 2016, 8, 19672‒19679.
(6) Li, C.; Koenigsmann, C.; Ding, W.; Rudshteyn, B.; Yang, K. R.; Regan, K. P.; Konezny, S. J.; Batista, V. S.; Brudvig, G. W.; Schmuttenmaer, C. A.; Kim, J.-H. Facet-Dependent Photoelectrochemical Performance of TiO2 Nanostructures: An Experimental and Computational Study. J. Am. Chem. Soc. 2015, 137, 1520‒1529. (7) Liu, G.; Wang, T.; Zhou, W.; Meng, X.; Zhang, H.; Liu, H.; Kako, T.; Ye, J. Crystal-Facet-Dependent Hot-Electron Transfer in Plasmonic-Au/Semiconductor Heterostructures for Efficient Solar Photocatalysis. J. Mater. Chem. C 2015, 3, 7538‒7542.
24
ACS Paragon Plus Environment
Page 24 of 35
Page 25 of 35
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Applied Materials & Interfaces
(8) Selcuk, S.; Selloni, A. Facet-Dependent Trapping and Dynamics at Anatase TiO2 Surfaces and Aqueous Interfaces. Nat. Mater. 2016, 15, 1107‒1113. (9) Tan, C.-S.; Hsu, S.-C.; Ke, W.-H.; Chen, L.-J.; Huang, M. H. Facet-Dependent Electrical Conductivity Properties of Cu2O Crystals. Nano Lett. 2015, 15, 2155‒2160. (10) Tan, C.-S.; Chen, Y.-J.; Hsia, C.-F.; Huang, M. H. Facet-Dependent Electrical Conductivity Properties of Silver Oxide Crystals. Chem. Asian J. 2017, 12, 293‒297. (11) Tan, C.-S.; Chen, H.-S.; Chiu, C.-Y.; Wu, S.-C.; Chen, L.-J.; Huang, M. H. Facet-Dependent Electrical Conductivity Properties of PbS Nanocrystals. Chem. Mater. 2016, 28, 1574‒1580. (12) Liu, G.; Yin, L.-C.; Pan, J.; Li, F.; Wen, L.; Zhen, C.; Cheng, H.-M. Greatly Enhanced Electronic Conduction and Lithium Storage of Faceted TiO2 Crystals Supported on Metallic Substrates by Tuning Crystallographic Orientation of TiO2. Adv. Mater. 2015, 27, 3507‒3512. (13) Kim, C. W.; Yeob, S. J.; Cheng, H.-M.; Kang, Y. S. A Selectively Exposed Crystal Facet-Engineered TiO2 Thin Film Photoanode for the Higher Performance of the Photoelectrochemical Water Splitting Reaction. Energy.
25
ACS Paragon Plus Environment
ACS Applied Materials & Interfaces
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Environ. Sci. 2015, 8, 3646‒3653. (14) Tan, C.-S.; Huang, M. H. Metal-like Band Structures of Ultrathin Si {111} and {112} Surface Layers Revealed through Density Functional Theory Calculations. Chem.‒Eur. J. 2017, 23, 11866–11871. (15) Yang, Y.-C.; Wang, H.-J.; Whang, J.; Huang, J.-S.; Lyu, L.-M.; Lin, P.-H.; Gwo, S.; Huang, M. H. Facet-Dependent Optical Properties of Polyhedral Au‒Cu2O Core‒Shell Nanocrystals. Nanoscale 2014, 6, 4316‒4324. (16) Hsu, S.-C.; Liu, S.-Y.; Wang, H.-J.; Huang, M. H. Facet-Dependent Surface Plasmon Resonance Properties of Au‒Cu2O Core‒Shell Nanocubes, Octahedra, and Rhombic Dodecahedra. Small 2015, 11, 195‒201. (17) Rej, S.; Wang, H.-J.; Huang, M.-X.; Hsu, S.-C.; Tan, C.-S.; Lin, F.-C.; Huang, J.-S.; Huang, M. H. Facet-Dependent Optical Properties of Pd‒Cu2O Core‒Shell Nanocubes and Octahedra. Nanoscale 2015, 7, 11135‒11141. (18) Ke, W.-H.; Hsia, C.-F.; Chen, Y.-J.; Huang, M. H. Synthesis of Ultrasmall Cu2O Nanocubes and Octahedra with Tunable Sizes for Facet-Dependent Optical Property Examination. Small 2016, 12, 3530‒3534. (19) Wang, H.-J.; Yang, K.-H.; Hsu, S.-C.; Huang, M. H. Photothermal Effects from Au‒Cu2O Core‒Shell Nanocubes, Octahedra, and Nanobars with Broad
26
ACS Paragon Plus Environment
Page 26 of 35
Page 27 of 35
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Applied Materials & Interfaces
Near-Infrared Absorption Tunability. Nanoscale 2016, 8, 965‒972. (20) Yang, K.-H.; Hsu, S.-C.; Huang, M. H. Facet-Dependent Optical and Photothermal Properties of Au@Ag‒Cu2O Core‒Shell Nanocrystals. Chem. Mater. 2016, 28, 5140‒5146. (21) Bi, Y.; Ouyang, S.; Umezawa, N.; Cao, J.; Ye, J. Facet Effect of Single-Crystalline Ag3PO4 Sub-microcrystals on Photocatalytic Properties. J. Am. Chem. Soc. 2011, 133, 6490‒6492. (22) Martin, D. J.; Umezawa, N.; Chen, X.; Ye, J.; Tang, J. Facet Engineered Ag3PO4 for Efficient Water Photooxidation. Energy Environ. Sci. 2013, 6, 3380‒3386. (23) Martin, D. J.; Liu, G.; Moniz, S. J. A.; Bi, Y.; Beale, A. M.; Ye, J.; Tang, J. Efficient Visible Driven Photocatalyst, Silver Phosphate: Performance, Understanding and Perspective. Chem. Soc. Rev. 2015, 44, 7808‒7828. (24) Zheng, B.; Wang, X.; Liu, C.; Tan, K.; Xie, Z.; Zheng, L. Highly-Efficiently Visible Light-Responsive Photocatalysts: Ag3PO4 Tetrahedral Microcrystals with Exposed {111} Facets of High Surface Energy. J. Mater. Chem. A 2013, 1, 12635‒12640. (25) Dong, C.; Wang, J.; Wu, K.-L.; Ling, M.; Xia, S.-H.; Hu, Y.; Li, X.; Ye, Y.; Wei, X.-W. Rhombic Dodecahedral Ag3PO4 Architectures: Controllable Synthesis,
27
ACS Paragon Plus Environment
ACS Applied Materials & Interfaces
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Formation Mechanism and Photocatalytic Activity. CrystEngComm 2016, 18, 1618‒1624. (26) Dong, P.; Wang, Y.; Li, H.; Li, H.; Ma, X.; Han, L. Shape-Controllable Synthesis and Morphology-Dependent Photocatalytic Properties of Ag3PO4 Crystals. J. Mater. Chem. A 2013, 1, 4651‒4656. (27) Yeo, B.-E.; Seo, Y.; Park, H.; Huh, Y.-D. Facet Effect of Ag3PO4 Crystals on Antibacterial Activities. Bull. Korean Chem. Soc. 2015, 36, 1904‒1907. (28) Lyu, L.-M.; Huang, M. H. Investigation of Relative Stability of Different Facets of Ag2O Nanocrystals through Face-Selective Etching. J. Phys. Chem. C 2011, 115, 17768‒17773. (29) Wang, H.; Bai, Y.; Yang, J.; Lang, X.; Li, J.; Guo, L. A Facile Way to Rejuvenate Ag3PO4 as a Recyclable Highly Efficient Photocatalyst. Chem. – Eur. J. 2012, 18, 5524–5529. (30) Yang, X.; Tang, H.; Xu, J.; Antonietti, M.; Shalom, M. Silver Phosphate/Graphitic Carbon Nitride as an Efficient Photocatalytic Tandem System for Oxygen Evolution. ChemSusChem 2015, 8, 1350‒1358. (31) Yan, T.; Zhang, H.; Liu, Y.; Guan, W.; Long, J.; Li, W.; You, J. Fabrication of Robust M/Ag3PO4 (M = Pt, Pd, Au) Schottky-Type Heterostructures for
28
ACS Paragon Plus Environment
Page 28 of 35
Page 29 of 35
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Applied Materials & Interfaces
Improved Visible-Light Photocatalysis. RSC Adv. 2014, 4, 37220‒37230.
29
ACS Paragon Plus Environment
ACS Applied Materials & Interfaces
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Figure 1.
SEM images of the synthesized Ag3PO4 (a) cubes, (b) rhombic
dodecahedra, (c) {100}-truncated rhombic dodecahedra, (d) tetrahedra, and (e) tetrapods.
Insets show magnified SEM images with scale bars equal to 500 nm.
30
ACS Paragon Plus Environment
Page 30 of 35
Page 31 of 35
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Applied Materials & Interfaces
Figure 2.
(a) A standard XRD pattern of Ag3PO4.
crystals with various shapes.
(b–f) XRD patterns of Ag3PO4
The stars indicate enhanced peak intensities due to the
uniformed particle shapes.
Figure 3. tetrahedra.
SEM images of smaller Ag3PO4 (a) rhombic dodecahedra and (b) Insets scale bars equal to 200 nm.
31
ACS Paragon Plus Environment
ACS Applied Materials & Interfaces
Figure 4.
(a) UV-vis diffuse reflectance spectra of Ag3PO4 rhombic dodecahedra. (b)
Tauc plot of (αhν)1/2 vs. energy (hν) for Ag3PO4 rhombic dodecahedra to determine their indirect optical band gap.
100 90 80 70
C/C0 (%)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 32 of 35
60 50 40 30 Tetrahedra Rhombic Dodecahedra Cubes
20 10 0 -30 -20 -10
0
10 20
30 40 50 60 70 80
90
Time (min)
Figure 5.
Extents of methyl orange photodegradation as a function of reaction time
using Ag3PO4 cubes, rhombic dodecahedra, and octahedra as the photocatalysts.
32
ACS Paragon Plus Environment
Page 33 of 35
DMPO Tetrahedra Rhombic Dodecahedra Cubes Fit
Intensity (a. u.)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Applied Materials & Interfaces
3460
3480
3500
3520
Magnetic field [G] Figure
6.
EPR spectra of DMPO-OH in the presence of photoirradiated Ag3PO4
crystals. The purified DMPO without any Ag3PO4 catalysts gives no EPR signal.
a
b
Electron-hole recombination
Figure 7.
c
Moderate electron transfer
d
High electron transfer
(a) Adjusted band diagram of Ag3PO4 with different degrees of surface
band bending for the {111}, {110}, and {100} facets.
In the diagram, qX is the
33
ACS Paragon Plus Environment
ACS Applied Materials & Interfaces
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 34 of 35
semiconductor electron affinity, Eg is the semiconductor band gap, Ec is the conduction band energy, Ev is the valence band energy, and Ef is the Fermi level. (b‒d) Drawings showing different photocatalytic responses of Ag3PO4 (b) tetrahedra with {111} facets, (c) rhombic dodecahedra with {110} facets, and (d) cubes with {100} facets.
Figure 8.
(a‒c) SEM images of a single Ag3PO4 (a) cube, (b) rhombic
dodecahedron, and (c) tetrahedron for electrical conductivity measurements with tungsten probes contacting a crystal.
(d) The measured I-V curves.
(e) SEM image
showing tungsten probes contacting the {110} and {100} faces of a {100}-truncated rhombic dodecahedron and the measured I‒V curves. 34
ACS Paragon Plus Environment
Page 35 of 35
100
Tetrahedra Rhombic Dodecahedra Cubes
90 80
Intensity (a. u.)
70
C/C0 (%)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Applied Materials & Interfaces
60 50 40 30 20
Tetrahedra Rhombic Dodecahedra Cubes
10 0 0
10
20
30
40
50
60
70
80
90
3460
Time (min)
3480
3500
Magnetic field [ G]
TOC Graphic
35
ACS Paragon Plus Environment
3520