Thermodynamic Properties of Nonaqueous Solutions. II. Free

by Eugene Luksha and Cecil M. Criss2. Department of Chemistry, University of Vermont, Burlington, Vermont (Received October 86, 1066). Electrode poten...
0 downloads 0 Views 699KB Size
1496

EUGENE LUKSHA AND CECILM. CRISS

Thermodynamic Properties of Nonaqueous Solutions. 11. Free Energies, Entropies, and Activity Coefficients of Selected Alkali Metal Halides in Anhydrous N-Methylformamidel

by Eugene Luksha and Cecil M. Criss2 Department of Chemistry, University of Vermont, Burlington, Vermont

(Received October 86, 1066)

Electrode potentials have been measured for cells of the type M,(Hg)lMX(NR!IF) 1AgX;Ag where M is Li, Na, K, or Cs and X is either C1- or Br-. These potentials have been combined with data in the literature to evaluate standard potentials for cells of the type M/MX(NMF)IAgX;Ag, from which standard free energies of formation and activity coefficients of LiC1, NaC1, KC1, CsC1, and NaBr in anhydrous N-methylformamide have been obtained. The activity coefficients were determined from 0.01 to approximately 0.1 m. Activity coefficients for KC1 solutions were extended to saturation by means of the cell Ag;AgCIIKCl(ml)lK,(Hg)(KCl(mz) 1AgCl;Ag. The free energies have been used in conjunction with heat data to obtain the standard partial molal entropies of the corresponding electrolytes.

Introduction Electromotive force studies in solvents with dielectric constants greater than that of water are exceedingly rare. Mandel and Decroly3 have examined the platinum-hydrogen and silver-silver chloride electrodes in formamide (dielectric constant, D 109.5). The same electrodes have been studied by Dawson and coworkers'~5 in N-Methylacetamide (D 165.5 at 40"). Pavolpoulos and Strehlow6have studied the platinumhydrogen and cadmium-cadmium chloride electrodes as well as several metal electrodes in formamide. The only electromotive force studies in the very high dielectric constant solvent, N-methylformamide (D 182.4),' have been those of Povarov and co-workerss who studied cells of the types

I

Ag;AgC11MCl(m) M,(Hg) IMCl(0.1) 1AgCl;Ag and M,(Hg) IMCl(4 lAgC1;Ag where M represents either Na or Cs for the first of these cells and Cs for the second. I n the first paper of this s e r i e ~the , ~ heats of solution of several alkali metal halides in anhydrous N-methylThe Journal of Physical Chemistry

formamide were reported. I n a continuation of the study of the thermodynamic properties of alkali metal halides in this solvent, electromotive forces have been measured for cells of the type M,(Hg)/MX(NMF) 1AgX;Ag

(A)

where M is Li, Na, K, or Cs, and X is either C1- or Br-. Standard potentials of the corresponding metals relative to the silver-silver halide electrode have been (1) This paper represents part of the work submitted by E. Luksha to the Graduate School of the University of Vermont in partial fulfillment of the requirement for the degree of Doctor of Philosophy. (2) To whom correspondence should be directed: Department of Chemistry, University of Miami, Coral Gables, Fla. (3) M. Mandel and P. Decroly, Nature, 182, 794 (1958); Trans. Faraday SOC.,56, 29 (1960). (4) L. R. Dawson, R. C . Sheridan, and H. C. Eckstrom, J. Phys. Chem., 65, 1829 (1961). (5)L. R. Dawson, W. H. Zuber, Jr., and H. C. Eckstrom, ibid., 69, 1335 (1965). (6) T. Pavolpoulos and H. Strehlow, 2. Phvaik. Chem. (Frankfurt), 2,89 (1954). (7) G. R. Leader and J. F. Gormley, J. Am. Chem. SOC.,7 3 , 5731 (1951). (8) Y.M. Povarov, A. I. Gorbanev, Y . M. Kessler, and I. V. Safonova, Dokl. Akad. Nauk SSSR, 142, 1128 (1962); 155, 1411 (1964). (9) R. P. Held and C. M. Criss, J. Phys. Chem., 69, 2611 (1965).

PROPERTIES OF ALKALIMETALHALIDES IN ANHYDROUS N-METHYLFORMAMIDE

1497

Electrodes. The silver-silver halide electrodes were prepared by the electrolytic method described by Ives and Janz.'* The electrodes were fabricated from 24 gauge platinum wire sealed in lead glass standard-taper joints. About 1 cm of wire was exposed. Electrical contact with the potentiometer leads was made through Wood's metal in the contact tube. At least six electrodes were prepared at a time, and those with a bias potential greater than 0.15 mv were discarded. All electrodes were stored in conductivity water until Ag;AgCl\KCl(md IKv(Hg)1KCl(m) IAgC1;Ag (B) ready for use. Silver-silver iodide electrodes were made in a similar manner. However, because of the Experimental Section high solubility of AgI in the presence of iodides, these Materials. N-Methylformamide was prepared in electrodes were rendered useless for measurements in N-methylformamide. the same manner as that described previou~ly.~The solvent generally had a conductance ranging from The dropping amalgam electrode consisted of a fine capillary joined to a standard taper joint which fitted 3 X 10" to 5 X ohm-' cm-I. The solvent was not used if the conductance exceeded 8 X ohm-' into the top of the cell. The capillary was joined to cm-l. Conductance values reported in the literature the amalgam reservoir through a stopcock. range from to 4 X ohm-' cm-1.7~*J0-12 Apparatus. The apparatus for cell A was of allKarl Fischer titrations indicated the water content to glass construction, designed similarly to that of Izmaibe less than 0.003%. Automatically recorded warming lov and Ivanova.16 It had three openings fitted with curves, analyzed by the usual extrapolation methods, standard taper joints. Two of these were for elecshowed an average melting range of -3.52 to -2.99'. trodes, the remaining one for filling the cell. The conThe solvent had a density of 0.9986 f O.OOO1 g/cc, centration cell was similar in design to that of Harned. l6 which agrees with the most recent literature value." Both cells were thermostated in a water bath at 25.00 Methods used in purifying LiC1, NaCl, KCl, CsCI, i 0.01' and both were coated externally with Siliclad and NaBr have been described elsewhere. Analyses (Clay Adams, Inc.) to eliminate electrical leakage from indicated that the chloride salts were bromide free.13 the water bath. All electromotive force measureAmalgams were prepared from triply distilled ments were made with a Leeds and Northrup Type mercury which had been bubbled through nitric acid K-3 potentiometer, using an unsaturated CdSOc and distilled once again. Potassium and sodium amal(Epply Laboratory) cell as a standard. The potengams were prepared by the electrolysis of concentrated tiometer was frequently checked against three such solutions of their carbonates, the carbonate solutions cells. Since the impedances of the amalgam cells were having been prepared from recrystallized reagent high, a Keithley Instruments Model 151 microvoltgrade carbonate salts. Lithium and cesium amalgams meter was connected in series with the positive terminal were prepared by electrolysis of concentrated solutions of the potentiometer and the positive terminal of the of their chlorides. The amalgams were washed with study cell. In order to reduce the noise to a tolerable conductivity water and anhydrous methanol, dried level and at the same time maintain a high input in vacuo at about 300', and filtered directly into the impedance, the microvoltmeter was shunted with a dropping electrode reservoir through a capillary tube. 100-kilohm resistor. The voltage sensitivity of this Spent mercury was recovered by bubbling through circuitry was 0.01 mv. A standard cell was connected nitric acid. In some cases the amalgam compositions had to be (10) C. M.French and K. H. Glover, Trans. Faraday SOC.,51, 1418 (1955). adjusted to specified values. This was carried out by (11) I. Sinyakov, A. I. Gorbanev, Y.M. Povarov, and Y.M. Kessler, diluting an amalgam of known composition with pure Izv. A M . Nauk SSSR, Otd. Khim. Nauk, 1514 (1961). mercury until the desired composition was obtained. (12) A. Strack, K.Swanda, and L. W. Bahe, J . Chem. Eng. Data, 9, Each batch of amalgam was analyzed several times 416 (1964). to determine the alkali metal content. These analyses (13) D. J. G.Ives and J. Jans, "Reference Electrodes-Theory and 1961. Practice," Academic Press Inc., New York, N. Y., were accomplished by decomposing a weighed amount (14) See ref. 13, pp 205-207. of amalgam in 0.1 A4 standard HCl solution and back(15) N. A. Izmailov and E. F. Ivanova, Zh. Fiz. Khim., 29, 1422 titrating the excess acid with standard NaOH solution, (1955). The analyses agreed within 1%. (16) H.8. Harned, J . Am. C h m . SOC.,51, 417 (1929). determined, and activity coefficients and the standard free energies of formation have been obtained for the solvated salts, LiC1, NaC1, KCl, CsC1, and NaBr. From the free energies and the known heats of solutioqg partial molal entropies of these salts in anhydrous N-methylformamide have been calculated. In addition, activity coefficients for KC1 have been extended to concentrations up to saturation by use of the concentration cell

~~

~

Volunte 70,Number 6 Mag 1066

1498

in series with reversed polarity to reduce the potential, since the electromotive force of the study cell was beyond the range of the potentiometer. Every precaution was taken against electrical leakage; the guarded circuits provided in the instrument were used effectively. Procedure. Before each measurement, the cell was washed with distilled water, rinsed with anhydrous methanol, and then dried in an air oven at 125". After removal from the oven, the cell was flushed with dry nitrogen and the dropping amalgam and silversilver halide electrodes (cell A) or the two dropping amalgam electrodes (cell B) were immediately inserted into their respective compartments. Preparation of the silver-silver halide electrodes immediately prior to insertion in the cell involved removing the electrodes from storage in conductivity water and soaking them for a few minutes in pure anhydrous N-methylformamide and t,hen for a few minutes in a solution of the same composition as that in the cell. Since the silver halide coating was very thin and the electrodes were not porous, a brief soaking period was sufficient for the removal of water. Solutions of the alkali metal halides were prepared by the addition of a weighed quantity of salt to 50.00 mi of N-methylformamide in an apparatus that could easily be mated to a third opening in the cell by means of a standard taper joint. This apparatus reduced to an absolute minimum contact between the atmosphere and the solution and was used to fill the cell immediately after the electrodes were inserted. Precautions were taken to avoid contaminating the cell solutions with grease. Potential measurements were generally initiated within a few minutes after the cell was placed in the thermostat. Readings were taken approximately every 5 min. All cells studied generally came to equilibrium within 45 min. After equilibrium was established, the potentials rarely varied by more than 0.3 mv from an average value during the period of observation. The cells were observed for a period of 1 hr, in general, and in a few cases as long aa 3 hr. Amalgam flow rates for each cell were varied from a continuous Aow to a few drops per minute. I n contrast to other investigator^,^^^'^ who have studied dropping amalgam electrodes in other nonaqueous solvents, no effect could be observed on the electromotive force of the cells because of flow rate, except for the lithium cell. The flow rate of the lithium amalgam electrode affected the potential only at low concentrations, but since electromotive force measurements at the lower concentrations were not used in the extrapolation to infinite dilution for remons discussed The JOUTTZU~ of Phg8icd Chemistry

EUGENE LUKSHAAND CECILM. CRISS

below, the phenomenon was of little practical consequence.

Results and Discussion All the amalgam electrodes exhibited abrupt decreases in electromotive force at low concentrations. This decrease occurred at about 0.01 m for the sodium, potassium, and cesium amalgams and at about 0.02 m for the lithium amalgam. This same phenomenon has been observed for this type of electrode by other investigators in methanol and f ~ r m a m i d e , ~but ~~~~~' the cause of the behavior is not understood. The fact that the sharp potential drop of these electrodes occurs only at the lower concentrations leads one to suspect that it is a result of an increase in the metal ion concentration around the electrode surface, caused by decomposition of the amalgam. This accounts for the fact that the effect is more pronounced in dilute solutions, but does not explain the failure of the increased amalgam flow rate to correct the condition. Experimental points that showed this behavior were neglected in the extrapolations and in most cases are not presented in the data. At concentrations greater than 0.02 m for the lithium cell and concentrations greater than 0.01 m for the other cells, the data are treated best by the method of H i t c h c ~ c k . ~ ~ The electromotive force of a cell containing a 1 :1 electrolyte and having its electrodes in their standard states is given by

E

=

E"

- 2RT -In my& n5

where the symbols have their usual meanings. The expanded Debye-Huckel equation gives the mean activity coefficient as log

y& =

+ Cm

- 6 , G

where 6, = 1.8248 X lo6-

dol"

(DT )' I 2

C is a constant, m is the molality, do and D are the density and dielectric constant of the solvent, respectively. For N-methylformamide at 25", D 182.4' and do 0.9986 g/cc, giving a value of 0.1439 (kg/mole)"' for 6,. Substitution of eq 2 into (1) and rearranging terms gives (17) J. H.Wolfenden, C. P. Wright, N. L. Ross Kane, and R. S. Buckley, Trans. F~T&V Soc., 23, 491 (1927). (18) G. Scatchard and R. F. Tefft, J . Am. Chem. SOC.,52, 2265 (1930). (19) D.I. Hitchcook, {bid., 50, 2076 (1928).

PROPERTIES OF ALKALIMETALHALIDES IN ANHYDROUS N-METHYLFORMAMIDE

2RT E+-lnmnS

(2.303)2RT6,6 nS

E" -

-

(2.303)2RTCm nS

Table I: Electromotive Force Data for Ek:ctrolytes in N-Methylformamide a t 25"

(3)

and substitution of the appropriate constants into eq 3 leads to

E

+ 0.11832 log m - 0 . 0 1 7 0 2 6 = E"

- 0.11832Cm

(4)

Since an amalgam electrode is employed, the measured potential is not the electromotive force represented by E in eq 4, but rather a potential, E', related to E by

E'

=

E - E"

(5)

where E" is the potential of a cell of the type

M 1 MX (soln) I M, (Hg) for some amalgam concentration y. To "correct" the observed potential to that which one would obtain for a pure metallic electrode, the value E" must be added to the observed potential. Making this substitution and setting the left-hand side of eq 4 equal to E"' gives EItI

=

E " - 0.11832Cm

(6)

The resultant potentials then refer to a cell employing a pure metallic electrode and may be written as MIMX(NMF) [AgX;Ag

1499

(C)

Table I summarizes the data. The first three columns give the molality of the cell solution, the measured potential, and the amalgam concentration of the dropping electrode, respectively. The fourth column gives the potential required to correct the observed potential to that for a pure metallic electrode. The fifth column gives the values of E"' in eq 6, and the sixth column gives the potentials for cells of type C. Cesium and lithium amalgams were adjusted to the exact compositions shown in Table I in order to be compatible with potential data for the single amalgam concentrations listed in the literature.20t21 Three separate batches of lithium amalgam used for the measurements gave reproducible results. Only one batch of cesium amalgam was used in the measurements. Three batches of sodium amalgam were used. Two of these were used for the sodium chloride cell (only one measurement was made with one batch) and one for the sodium bromide cell. Only one batch of potassium amalgam was used in the measurements for cell A. Sodium amalgam cell data were corrected to the standard state electrode using the data of Richards

ZIP

wt %

m

E'

0.006573 0.01126 0.01750 0.01933 0.02617 0,02914 0.03505 0.04309 0.05130 0.08755

2.41457 2.39854 2.38061 2.37692 2.36598 2.36092 2.35159 2.34127 2.33519 2.31114

LiCl 0.0350 0.0350 0.0350 0.0350 0.0350 0.0350 0.0350 0.0350 0.0350 0.0350

0.9502 0.9502 0.9502 0.9502 0.9502 0.9502 0.9502 0.9502 0,9502 0.9502

3.1052 3.1164 3.1207 3.1220 3,1262 3.1265 3.1264 3.1264 3,1289 3.1312

3.3648 3,3487 3.3080 3.3271 3.3162 3.3111 3.3018 3.2915 3,2854 3,2616

0.01229 0.02488 0.03671 0.03742 0.05897 0.07924 0.07963 0.08106 0.09913

2.17255 2.13750 2.11853 2.12728 2.09596 2.07976 2.08090 2.07940 2.06931

NaCl 0.1291 0.1291 0.1291 0.1636 0.1291 0.1291 0.1291 0.1291 0.1291

0.8625 0.8625 0.8625 0.8542 0.8625 0.8625 0.8625 0.8625 0.8625

2.8071 2.8075 2.8080 2.8094 2.8089 2.8072 2.8086 2.8080 2.8077

3.0351 3.0000 2.9810 2.9815 2.9585 2.9423 2.9434 2.9419 2.9318

0.009616 0.01928 0.02751 0.03318 0.04041 0.04829 0.06297 0.07018

2.22877 2.19384 2.17613 2.16757 2.15792 2.14923 2.13690 2.13094

KC1 0.3024 0.3024 0.3024 0.3024 0.3024 0.3024 0.3024 0.3024

1,0328 1.0328 1.0328 1.0328 1,0328 1.0328 1.0328 1,0328

3.0213 3.0214 3.0215 3.0223 3.0224 3.0226 3.0233 3.0227

3.2616 3.2266 3.2089 3.2004 3.1907 3.1820 3.1697 3.1637

0.009015 0.01846 0.03003 0.03983 0.05229 0.06436 0.07092

2.11136 2.07576 2.05144 2.03727 2.02387 2.01373 2.00879

CSCl 0.1875 0.1875 0.1875 0.1875 0.1875 0.1875 0.1875

1.119 1.119 1.119 1.119 1.119 1.119 1.119

2.9868 2.9873 2.9874 2.9872 2.9873 2.9875 2.9872

3.230 3.195 3.170 3.156 3.143 3.133 3.128

0.008701 0.02227 0.03142 0.04295 0.05441 0.07589

2.11872 2.07056 2.05409 2.03784 2.02700 2.00927

NaBr 0.2353 0.2353 0.2353 0.2353 0.2353 0.2353

0.8402 0.8402 0.8402 0.8402 0.8402 0.8402

2.7135 2.7127 2.7135 2.7128 2.7136 2.7123

2.9589 2.9108 2.8943 2.8780 2.8672 2.8495

E"

E

and Conant22 and Lewis and K r a ~ s . ~ 3Similar corrections for the potassium amalgam cell were made (20) G. N. Lewis and F. G. Keyes, J. Am. Chem. Soc., 35,340 (1913). (21) H. E. Bent, G. S. Forbes, and A. F. Forziatti, ibid., 61, 709 (1939).

Volume 70, Number 6 May 1986

1500

EUGENELUKSHAAND CECILM. CRISS

3126 3.122 3.118 3.114

3.110 A

I/-

-

0

.

-

3.1061

5 3.1021 v)

-

w

- -.01

a

-

-

a

-

m

e .02

-CsICsCI (NMF) /AgCI; Aq

a

I

1

-03

-

No/ NaCI(NyF)/AgCI;Ag F

a

No/NaBr (NMF)/AgBt;Ag

1

.04

1

-

K / KCI (NMF)/AgCl;Ag

-- -

w

w

-

-

-

-

-

-

a 1

W

w

.05 .06 Molol ity

,07

.08

.OS

.IO

I

Figure 1. E ” ’ us. molality for cells of type C.

using the data of Bent and Gelfellan24and Lewis and Keyes.26 The existence of potential data as a function of amalgam concentration made it unnecessary for sodium and potassium amalgams to be adjusted. Figure 1 shows values of E”’ plotted against the molality and extrapolated to infinite dilution by the method of least squares to obtain E”. Since the potentials below 0.01 m for all cells suffer very large decreases (as much as 50 mv), they have been omitted from Table I and Figure 1 and were not included in the least-squares treatment. Although the decrease in potential for the lithium cell occurs in solutions more than 0.02 m, the really abrupt decrease occurs only at concentrations below 0.01 m; consequently, the data are shown down to a concentration of about 0.01 m but have not been included in the least-squares treatment. Because of the apparent curvature of E”’ us. m for the sodium chloride cell at higher concentrations, the two points for the most concentrated soluTable II: Standard Potentials for Cells of Type C Cell

EO

LilLiCl( NMF)IAgCl;Ag NalNaCl( NMF)IAgCl;Ag KIKCl( NMF)IAgCl;Ag CsICsCl(NMF)IAgCl;Ag Ne[NaBr( NMF) 1AgBr;Ag

3.1237 2.8067 3.0212 2.987 2.7135

The Journal of P h y a a Chemistry

tions were not included in the least-squares treatment. The standard electrode potentials for the various cells evaluated by this treatment are given in Table 11. Smoothed values of the electromotive force, E , for cells of type C have been calculated from smoothed values of E”’ at round values of the molality and are given in Table 111.

Activity Coefficients of Electrolytes in N-Methylformamide The smoothed electromotive forces listed in Table I11 are useful for obtaining activity coefficients of the corresponding salts in N-methylformamide. Rearrangement of eq 1 gives E” - E , - log m (7) log ’* = 0.11832 from which -yk for the various electrolytes have been evaluated. These are listed also in Table 111, along with the few corresponding values for NaCl and CsCl reported in the literature.* From the knowledge of activity coefficients in dilute solutions, activity coefficients at higher concentrations can be evaluated from cell B by the relationship (22) T. W. (1922). (23) G. N. (24) (25)

Richards and J. B. Conant, J. Am. Chem. SOC.,44, 601

Lewis and C. A. Kraus, ibid., 32, 1458 (1910). H. E. Bent and E. S. Gelfellan, ibid., 55, 3989 (1933). G. N. Lewis and F. G. Keyes, ibid., 34, 119 (1912).

PROPERTIES OF ALKALIMETALHALIDES IN ANHYDROUS N-METHYLFORMAMIDE

1501

Table 111: Smoothed Values of E and Activity Coefficients for Round Concentrations for Cell C --------NsCl--

-----LiClE

nL

3.3629 3.3288 3.3094 3.2959 3.2857 3.2776 3.2709 3.2652 3.2602

0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.10

Yi

E

0.951 0,923 0.898 0.876 0.854 0,834 0,815 0,796 0.780

3.0455 3.0110 2.9911 2.9772 2.9666 2,9580 2.9498 2.9430 2.9369 2,9313

r---KClY i

0.958 0.938 0.922 0.906 0.890 0.878 0.883 0.881 0.883 0.885

CsCl

I

Yi"

E

Y t

E

Yi

0.964 0.963

3.2598 3.2251 3.2051 3.1910 3.1802 3.1715 3.1642

0.962 0.945 0.929 0.921 0.906 0.895 0,885

3.225 3.190 3.170 3.156 3.145 3.136 3.128

0.967 0.954 0.945 0.936 0.929 0.922 0.916

0.950 0.945

Y i O

0.969 0.963

0.952 0.944 0.940

---NaBr---. E

2.9517 2.9167 2,8963 2.8819 2.8707 2.8616 2.8540 2,8473

Y*

0.969 0.958 0.951 0.943 0.938 0.934 0.929 0.925

0.940

Literature values (see ref 8).

E

RT

a1

RT

ml

= -In= -In-+ nS a2 nS m2

RT

-InnS

yk,~

Y*:,Z

(8)

where the subscripts refer to the respective cell solutions. Results of such measurements for cell B are listed in Table W . The first column gives the potential, E , for the cell and the remaining columns give the molalities, ml and m2, and activity coefficients, y*,1 and yi,2 of the reference and test solutions, respectively. A comparison of the activity coefficients obtained from this work and those in the literature shows the present data to have somewhat lower values than those previously reported.* In view of the uncertainties in amalgam cell measurements in nonaqueous solutions, the disagreement is not large.

Table IV : Electromotive Force Data and Activity Coefficients for the Cell, Ag;AgCl IKCl(rn1) Hg IKCKmd IAgC1;Ag

0.01469

-0,02525 -0,05172 - 0.07341

0.05570 0.05585 0.05593 0.05526

0.899 0.899 0.899 0.899

0.04096 0.09247 0.1532 0.2333

0.919 0.888 0.898 0.889

In the first paper of this ~ e r i e sthe , ~ heats of solution for sodium halide salts and lithium chloride showed limiting slopes considerably exceeding the theoretical values, suggesting ionic association for these electrolytes in anhydrous N-methylformamide. Examination of the activity coefficients of the same electrolytes leads one to the conclusion that ionic association exists to only a slight extent, if at all. This is in agreement with the conclusion drawn by Dawson and co-workers6 from their study of activity coefficients of HC1 in N-

methylacetamide. However, if one assumes that the deviations in activity coefficients from the DebyeHuckel theory are primarily caused by a slight amount of ionic association, then because of the decreasing order in activity coefficients as one goes from CsCl LiCl, one would expect that ionic association would be greatest for LiCl and smallest for CsCI. The possibility of ionic association in this solvent is being investigated further and will be reported in a future communication.

Standard Free Energies and Entropies of the Solvated Electrolytes The general reaction for cell C is

M(s)

+ AgX(s) +Ag(s) + MX(so1n)

and the corresponding standard free-energy change for this reaction is

+

AF0 = AFo~x(soin) A F O A ~ ( ~) A F o ~ c s ,- A F O A ~ X ( = ~ ) -n5E0

Table V : Standard Free Energies and Heats of Formation and Partial Molal Entropies of Alkali Metal Halides in N-Methylformamide

Salt

LiCl NaCl KCI CsCl

NaBr

AFP,

AHP,

koal/ mole

ked/ mole"

-98.4 -90.96 -95.89 -95.11 -85.5

( -110.8)b

- 99.51 - 103.86 -102.7 90.40

-

so, eu

(-8.7)' 10.3

15.1 21.3 13.8

" From heat of solution data of ref 9 and heats of formation of crystalline salts from ref 26. Estimated.

'

~

Volume 70, Number 6 May 1966

J. M. NOTLEYAND h/I. SPIRO

1502

The standard free energy of formation of a solvated salt MX is then given by A F ' M X ( ~ O I ~=) AFOA~X(B)- n5E'

Values for the standard free energies of formation have been calculated for the corresponding solvated salts and are listed in Table V. The standard free energies of formation for the silver halides were obtained from Latimer. 26 Heats of solution for LiC1, NaC1, KC1, CsCI, and NaBr previously reported, when combined with the heats of formation of the crystalline salts26 and free-

energy data obtained in this work, give the standard partial molal entropies for the corresponding salts. These entropies are also listed in Table V. The entropy given for LiCl is in considerable doubt since the heat of solution used in its evaluation is only an estimate. Acknowledgment. The authors are grateful to the U. S. Atomic Energy Commission, which supported this work through Contract AT-(30-1)-3019. ( 2 6 ) W. M. Latimer, "The Oxidation States of the Elements and their Potentials in Aqueous Solutions," 2nd ed, Prentice-Hall Ino., New York, N. Y.,1959.

Transference Numbers and Ionic Conductances in Formamide at 25'1

by J. M. Notley and M. Spiro Department of Chemistry, Imperial College of Science and Technology, London S.W.7, England (Received October 27, 1966)

The cation and anion constituent transference numbers of potassium chloride were measured at 25" at five concentrations from 0.01 to 0.1 N by the direct moving-boundary method, using as solvent formamide specially freed from ionic impurities. The addition of water had little effect on the results. The limiting transference numbers were combined with equivalent conductances from the literature to give individual ionic conductances in formamide. Ionic solvation numbers were calculated from them by means of the Robinson and Stokes modification of Stokes' law. The conductances and viscosities of 24 uni-univalent salts in formamide, measured by Davis, et al., were reexamined so as to give limiting conductances and viscosity B , coefficients. The concentration dependence of conductance in formamide was found to be strongly affected by the viscosity correction.

Introduction To attain a better understanding of ion-solvent interaction, we need accurate data on the properties of electrolytes a t infinite dilution and, if a t all possible, on the properties of single ions because cation-solvent and anion-solvent interactions are different. For most properties of electrolytes, the fraction to be attributed to the individual ions is uncertain except in the case of conductance where an unambiguous assignment can be made by means of transference numbers. UnThe Journal of Physical Chemistry

fortunately, although there are accurate conductance data for dozens of nonaqueous solvents, transference numbers of comparable accuracy exist only for a few: methanol2 (dielectric constant, Q 31.5), ethanol3 (E (1) Presented in Sept 1965 at the 16th Meeting of C.I.T.C.E. in Budapest, Hungary. (2) J. A. Davies, R. L. Kay, and A. R. Gordon, J . Chem. Phys., 19, 749 (1951); J. Smisko and L. R. Dawson, J . Phys. Chem., 59, 84 (1955). (3) J. R. Graham and A. R. Gordon, J . Am. Chem. SOC.,79, 2350 (1957);J. Smisko and L. R. Dawson, J. Phys. Chem., 59, 84 (1955).