Treating the PEDOT:PSS surface with hydroquinone enhances the

10 mins ago - HQ treatment of the PEDOT:PSS surface lowered the hole transport barrier at the interface between the PEDOT:PSS and the active layer...
0 downloads 0 Views 1MB Size
Subscriber access provided by University of Sunderland

Organic Electronic Devices

Treating the PEDOT:PSS surface with hydroquinone enhances the performance of polymer solar cells Sujung Park, Myung Joo Cha, Jung Hwa Seo, Jinhee Heo, Dongchan Lim, and Shinuk Cho ACS Appl. Mater. Interfaces, Just Accepted Manuscript • DOI: 10.1021/acsami.8b15551 • Publication Date (Web): 08 Nov 2018 Downloaded from http://pubs.acs.org on November 8, 2018

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 45 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

Treating the PEDOT:PSS surface with hydroquinone enhances the performance of polymer solar cells Sujung Park, Myung Joo Cha, Jung Hwa Seo, Jinhee Heo, Dong Chan Lim and Shinuk Cho*

Sujung Park, Prof. Shinuk Cho Department of Physics and EHSRC, University of Ulsan, Ulsan 44610, Republic of Korea *E-mail: [email protected]

Myung Joo Cha, Prof. Jung Hwa Seo Department of Materials Physics, Dong-A University, Busan 49315, Republic of Korea

Dr. Jinhee Heo, Dr. Dong Chan Lim

ACS Paragon Plus Environment

1

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 2 of 45

Surface Technology Division, Korea Institute of Materials Science (KIMS), Changwon 51508, Republic of Korea.

Keywords: organic photovoltaic, surface modification, hole transport layer, PEDOT:PSS, hydroquinone

ABSTRACT

The

introduction

of

poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate)

(PEDOT:PSS) as a standard hole transport layer greatly increased the efficiency of early organic solar cells. However, because PEDOT:PSS has a metallic property, it can still form a barrier by means of metal–semiconductor contact at its interface with the photoactive layer. In this study, we modified the PEDOT:PSS surface with hydroquinone (HQ) to remove that barrier. HQ treatment of the PEDOT:PSS surface lowered the hole

ACS Paragon Plus Environment

2

Page 3 of 45 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

transport barrier at the interface between the PEDOT:PSS and the active layer. In addition, because of the secondary doping effect of HQ, the sheet resistance of the PEDOT:PSS surface decreased by almost two orders of magnitude. As a result, the device fabricated with the HQ-modified PEDOT:PSS showed a 28% increase in efficiency compared to the device without HQ treatment. Modifying the PEDOT:PSS surface with HQ solution is an easy way to effectively boost the performance of polymer solar cells.

ACS Paragon Plus Environment

3

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 4 of 45

INTRODUCTION

Polymer bulk heterojunction (BHJ) solar cells have attracted much attention for their potential applications in large-area flexible devices because they are lightweight, low cost, and simple to fabricate.1-5 Since the first report on polymer BHJ solar cells in 1995,6 substantial progress has been made, raising device efficiencies by more than 13% through improvements in the design and synthesis of active materials,7-10 the optimization of nanoscale morphology,11-13 and interface engineering.14-18 Of course, the most important component in high efficiency solar cells is high performing active materials, but developing new and better active materials requires a lot of time and effort. Therefore, a cost-effective approach to improving the performance of existing materials is maximizing charge collection efficiency through interface engineering. The insertion of an electron or hole transport layer is part of interface engineering in a broad sense. Numerous organic and inorganic materials that could function as hole and electron extraction layers have been developed and studied to enhance the performance of BHJ solar cells.19-23 The most widely used inorganic buffer layer materials are probably metal oxides. A variety of transition metal oxides, such as ZnO, TiO2, NiO and MoO3 have been developed as either hole or electron transport materials for fabricating high performance and cost-effective BHJ solar cells due to their advantages of environmental stability, high transparency and high carrier mobility.24-26 Organic-based buffer materials are much more diverse. Dozens of novel synthetic materials which can be classified in conjugated polyelectrolyte,27,28 small molecule transport materials,29,30 polymer buffer materials,31,32 etc., have been developed and successfully applied as a buffer layer in BHJ solar cells. Among the organic-based hole transport materials, however, poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) remains the

ACS Paragon Plus Environment

4

Page 5 of 45 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

most widely used material even though it is the oldest. In early studies of organic BHJ solar cells, PEDOT:PSS offered superior performance in many ways. First, PEDOT:PSS showed excellent hole extraction because of a well-matched work function (~5.1 eV) for the highest occupied molecular orbital (HOMO) level of the donor polymer.33-35 Second, PEDOT:PSS delivered better adhesion between the inorganic ITO electrode and the organic active layer.36, 37 In addition, PEDOT:PSS induced uniform deposition of the active layer by smoothing the ITO surface.38 Now, various hole transport materials have been newly developed and used to replace PEDOT:PSS in BHJ solar cells. Nonetheless, PEDOT:PSS is still the best hole transport material in terms of process simplicity and performance consistency. In fact, PEDOT:PSS is the standard hole transport material; the performance of each newly developed hole transport material is judged by whether it is better or worse than PEDOT:PSS. Until now, interface engineering for organic BHJ solar cells has focused mainly on problems that occur at the interface between the organic active layer and the charge transport layer, which uses a metal-oxide such as ZnO, TiO2, or MoO3. In solar cells with a metal-oxide charge transport layer, many surface treatment methods, such as polar solvent treatment,39, 40 surface doping,41-44 or the insertion of a thin conjugated polyelectrolyte layer,45, 46 are applied to improve the interfacial properties between the inorganic metal-oxide layer and the organic BHJ layer. However, the literature contains only a few reports of surface treatments for the PEDOT:PSS hole transport layer. Recently, surface modifications of PEDOT:PSS were reported by adding a p-type dopant47 or treating it with either an alcoholic polar solvent48, 49 or a high boiling point solvent.50 However, those studies focused on increasing the conductivity of PEDOT:PSS. Furthermore, most studies about modifying the PEDOT:PSS surface have considered only inverted planar perovskite solar cells, which have interfacial problems between the inorganic

ACS Paragon Plus Environment

5

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 6 of 45

metal-oxide transport layer and organic active layer similar to those in organic BHJ solar cells. Although several investigations have considered the interfacial problem between PEDOT:PSS and the active layer in organic BHJ solar cells,51-53 it is true that the interfacial problem between PEDOT:PSS and the active layer was much less considered compared to the interfacial problem between metal oxides and the active layer, probably, because PEDOT:PSS was itself understood to be a modifying material for the ITO surface. Conventionally, single-layer BHJ cells, which have a cathode/active/anode structure, were treated as metal-insulator-metal diodes. However, a careful investigation of dark current found that the fundamental unit is a semiconductor–metal Schottky junction.54-56 Because PEDOT:PSS also has a metallic property (though with relatively low conductivity),57,58 it still carries the possibility of forming a Schottky-type contact barrier at the interface. Therefore, in this work, we have modified the PEDOT:PSS surface with hydroquinone (HQ) by spin-coating to reduce the Schottky-type contact barrier that can interfere with hole transport. The conjugated polymer is an electron-rich system, and ultraviolet photoelectron spectroscopy (UPS) measurements showed that PEDOT:PSS and the conjugated polymer form an n-type Schottky contact. Surface treatment of PEDOT:PSS with HQ changed the energy level bending properties in a direction more favorable to hole extraction. In addition, HQ treatment significantly reduced surface resistivity. Those HQ-derived surface property improvements nearly doubled the density of the extracted holes. Consequently, a power conversion efficiency (PCE) of up to 10.18% was achieved from a conventionally structured BHJ solar cell using poly[[4,8-bis[5(2ethylhexyl)thiophen-2-yl]benzo[1,2-b:4,5-b0]dithiophene-2,6-diyl][3-fluoro-2-[(2ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl]] (PTB7-Th) and [6,6]-phenyl-C71-butyric acid

ACS Paragon Plus Environment

6

Page 7 of 45 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

methyl ester (PC71BM) as the active layer, a ~28% increase in efficiency compared to solar cells without HQ treatment. RESULTS AND DISCUSSION

Figure 1a shows a schematic of the conventional BHJ solar cell architecture and the chemical structures of the materials used in this study (PTB7-Th, PC71BM, PEDOT:PSS, and HQ). HQ treatment was simply done by spin-coating HQ solution diluted with isopropyl alcohol (IPA) on the PEDOT:PSS layer. HQ is weak polar solvent with a dipole moment of 1.4 Debye. Its effects are similar to those of alcoholic solvents such as methanol and ethanol, which are often used for surface treatment,48,49,59 because they all have two hydroxyl groups (-OH). Because HQ has a high boiling point (287 °C), it combines the effects of an alcoholic polar solvent and a high boiling point solvent. Furthermore, HQ can lose an H+ from one of the hydroxyls to form a monophenolate ion or lose an H+ from both to form a diphenolate ion. Therefore, we expected HQ to provide additional protonation doping on the PEDOT:PSS surface. Figure 1b shows the energy level diagrams of each material used in our PTB7Th:PC71BM solar cells. The work-function of the HQ-treated PEDOT:PSS was

ACS Paragon Plus Environment

7

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 8 of 45

determined by UPS measurement (Figure S1). Other energy level values, such as the HOMO/LUMO level of active materials and conduction band minimum level of the ZnO nanoparticles, were obtained from the literature.

Figure 2a shows the current density (J)-voltage (V) characteristic curves of conventionally structured PTB7-Th:PC71BM solar cells. Details of the performance of these solar cells are listed in Table 1, and external quantum efficiency (EQE) spectra are presented in Figure S2 in the Supporting Information. To find the proper dilution ratio for the HQ solution, we varied the ratio of HQ to IPA from 0.2 wt% to 2.0 wt%. Solar cells with a pristine PEDOT:PSS layer (without HQ treatment) yielded a PCE of 7.98% with a Jsc of 15.6 mA/cm2, a Voc of 0.782 V, and a fill factor (FF) of 0.654. The performance of solar cells with an HQ-modified PEDOT:PSS layer gradually increased along with the HQ concentration up to 1.0 wt%. The most efficient solar cell had a PCE of 10.2%, with a Jsc of 18.9 mA/cm2, a Voc of 0.793 V, and an FF of 0.680. However, when the HQ concentration exceeded 1.0 wt%, cell efficiency decreased rapidly. Since we have used HQ solution diluted with alcohol solvent such as methanol or ethanol, it

ACS Paragon Plus Environment

8

Page 9 of 45 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

has possibility that this performance enhancement may originated by alcohol solvent because alcohol solvent also can modify the PEDOT:PSS surface a little. However, the performance increase was not observed when the PEDOT:PSS surface was treated with a simple alcohol solvent. Thus, the performance enhancement was obviously an effect of the HQ (Figure S3). In addition, the performance enhancements from the HQ treatment were universal (clearly observable in other polymer BHJ systems). Figure S4a and S4b show the J-V characteristic results from poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C61-butyric acid methyl ester (PC61BM), poly[[4,8-bis[(2ethylhexyl)oxy]benzo[1,2-b:4,5-b’]dithiophene-2,6-diyl][3-fluoro-2-[(2-ethylhexyl)carbonyl]-thieno-[3,4-b]thiophenediyl]] (PTB7) and PC71BM, respectively. Note that the optimal HQ concentration varied a bit depending on the BHJ active material. The device with the PTB7:PC71BM mixture showed the highest efficiency at the same optimal dilution ratio of HQ and IPA as the PTB7-Th:PC71BM device, whereas the P3HT:PC61BM device showed the best efficiency at 0.8 wt%.

ACS Paragon Plus Environment

9

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 10 of 45

As clearly shown in the J-V results, the PCE enhancement in devices with HQ treatment stemmed from improvements in Jsc. In an organic BHJ solar cell, factors that significantly influence Jsc are improvements in the charge extraction efficiency through energy level changes or morphology changes at the interface. First, to investigate the influence of HQ treatment on energy level changes in both the PEDOT:PSS and PTB7Th donor polymer, we performed UPS measurements, as shown in Figure 3a. To observe the band bending degree of the PTB7-Th polymer caused by the change in the PEDOT:PSS surface properties, we measured the UPS with various thicknesses of PTB7-Th polymer, which we controlled by changing the solution concentration from 0.003 wt% to 0.3 wt%. When PTB7-Th was deposited on pristine PEDOT:PSS, the secondary edges shifted toward higher binding energies as the concentration of the PTB7-Th solution increased. The total vacuum level (VL) shift at the saturated coverage was 0.25 eV for PTB7-Th deposited on pristine PEDOT:PSS and 0.35 eV for PTB7-Th deposited on HQ-treated PEDOT:PSS. The right side of the figure shows the evolution of the HOMO onsets for PTB7-Th. Figures 3c and 3d show the C 1s and S 2p emission lines from the PTB7-Th layers on PEDOT:PSS. These XPS analyses show the energies

ACS Paragon Plus Environment

10

Page 11 of 45 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

of the core levels, allowing us to probe the band bending. As the concentration of PTB7Th solution increased to 0.3 wt%, the S 2p emissions increased in intensity, and the PSS emissions became attenuated because of the thicker PTB7-Th layer. Using that S 2p and C 1s peak shift between the thin and thick PTB7-Th layers, we determined the band bending energies: 0.28 eV for PTB7-Th on pristine PEDOT:PSS and 0.32 eV for the PTB7-Th on PEDOT:PSS with HQ treatment. Figures 3e and 3f show energy level diagrams obtained by summarizing the UPS and XPS results. The hole injection barrier (φh) was estimated using the energy difference between the EF and HOMO levels extracted from the UPS results. Although the band bending degree of PTB7-Th on the HQ-treated PEDOT:PSS was slightly larger than that of PTB7-Th on pristine PEDOT:PSS, the φh of the PTB7-Th on the HQ-treated PEDOT:PSS was smaller than on pristine PEDOT:PSS. Thus, in terms of hole transport, HQ treatment improved the interfacial contact barrier and facilitated hole transfer.

The effect of the energy level change from HQ treatment was consistently confirmed in several experiments, as shown in Figure 4. After HQ treatment, although the hole

ACS Paragon Plus Environment

11

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 12 of 45

extraction barrier was reduced, the electron injection barrier became larger. Normally, electrons injected from the anode electrode generate undesirable leakage current. Within the operation range between 0 V and Voc, the flow of leakage current is opposite to the photocurrent, thereby reducing the device efficiency. Therefore, we expected that the enlarged electron injection barrier created by the HQ treatment would reduce the leakage current, and indeed we found significantly reduced leakage current in the device with HQ-modified PEDOT:PSS, as shown in the J-V characteristics measured under dark conditions (Figure 4a). The effect of reducing the interfacial contact barrier by HQ treatment was confirmed by impedance spectroscopy (IS), which is a useful method for analyzing the interfacial transport and recombination properties of solar cells. Figure 4b shows the Nyquist plots of the IS results measured under illumination at

Voc. Devices both with and without HQ treatment appear on one semicircle without a transmission line (TL). The absence of the TL indicates that solar cells with and without HQ treatment can be interpreted using the Gerischer impedance model.60, 61 Because neither transport resistance nor recombination resistance can be unambiguously determined in the Gerischer impedance model, only relative comparisons are possible,

ACS Paragon Plus Environment

12

Page 13 of 45 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

and the combined effective resistance is called Gerischer resistance. Because all device fabrication parameters were identical for both solar cells (except for the HQ treatment of the PEDOT:PSS surface), the difference in the IS spectra likely originated from that interface modification. The real impedance decreased significantly in the device with the HQ-modified PEDOT:PSS, which indicates that the surface modification improved the interfacial contact. The enhanced charge extraction (CE) property from the HQ treatment was confirmed by measurement, as shown in Figure 4c. Using the CE measurement, we calculated the charge extraction density directly, as shown in Figure 4d. Direct comparison between the devices with and without HQ treatment indicated that the device with HQ treatment had almost double the charge extraction density of the untreated device.

One more thing to note in the energy diagrams obtained through UPS measurements (Figures 3e and 3f) is the VL shift. When an organic layer contacts a metallic layer, the organic layer can be affected by the potential of the surface dipole. In general, VL shifts can yield the magnitude and direction of the interfacial dipole that originates from the

ACS Paragon Plus Environment

13

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 14 of 45

polarization of the charge carrier density at the metallic surface. Therefore, the larger VL shift indicates that the PEDOT:PSS with HQ treatment has more free charge carriers than the pristine PEDOT:PSS, which indicates the possibility that the HQ allows secondary doping of the PEDOT:PSS surface. The conjugated PEDOT is positively doped by the sulfonate anionic groups of the PSS.62 Because the PEDOT:PSS is not fully doped, it can be doped to a higher level by an additional protonating source. In fact, many papers have reported on secondary doping of PEDOT:PSS.63-65 To investigate the possibility that the HQ treatment was responsible for secondary doping, we measured the conductivity sheet resistance of the PEDOT surface (Table 2). Pristine PEDOT:PSS had a conductivity of 0.18 (±6.35×10-3) Ω-1cm-1 and sheet resistance of 1,340±9.87 kΩ/□. The PEDOT:PSS with HQ treatment, however, showed a significantly reduced sheet resistance of 59.1±0.92 kΩ/□, almost two orders of magnitude lower. Such reduction of surface resistance also can be originated by the reduction of PSS.66 However, in our case, no PSS reduction was observed in XPS study (see Figure S9). Furthermore, if there was a reduction of PSS by HQ treatment, there would have been a significant morphology change. However, we couldn’t get any significant change of surface morphology of

ACS Paragon Plus Environment

14

Page 15 of 45 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

PEDOT:PSS by HQ treatment. Based on these facts, we concluded that additional doping by hydroxyl group of HQ would be main mechanism rather than PSS reduction.

We also found evidence of secondary doping in our Fourier-transform infrared spectroscopy (FTIR) measurements. Figure 5a shows the mid-IR absorption spectra obtained from the pristine PEDOT:PSS and HQ-modified PEDOT:PSS. Because the PEDOT:PSS was dispersed in water, we used ZnSe as a substrate instead of KBr, which has a weak resistance in water. Direct comparison between the absorption peaks of pristine PEDOT:PSS and HQ-modified PEDOT:PSS indicates that the intensity of all the absorption peaks in the HQ-modified PEDOT:PSS increased slightly. A conducting polymer in a doped state exhibits very strong doping-induced infrared bands, so called infrared active vibration (IRAV) modes, in the mid-IR region (typically between 400 cm-1 and 1500 cm-1, the fingerprint region). All the peaks observed between 500 cm-1 and 1500 cm-1 in both the pristine PEDOT:PSS and HQ-modified PEDOT:PSS are IRAV modes. Normally, the intensity of the IRAV modes increases slightly with the doping

ACS Paragon Plus Environment

15

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 16 of 45

level.67 Therefore, slightly increased IRAV modes in the HQ-modified PEDOT:PSS clearly indicate that the PEDOT:PSS was secondarily doped by the HQ.

Lastly, to confirm whether the improvement of solar cell performance was caused by the morphology change at the interface, we took atomic force microscopy (AFM) measurements for the PEDOT:PSS layers with and without HQ treatment. Figure 5b shows the AFM image of the pristine PEDOT:PSS, which had a root mean square (RMS) roughness value of ~2.1 nm. Figure 5c shows the AFM image of the HQmodified PEDOT:PSS, and it had a RMS roughness value of ~1.8 nm. Although the RMS roughness of the HQ-modified PEDOT:PSS layer was slightly lower than that of the pristine PEDOT:PSS, the surface morphology did not change significantly. Therefore, we conclude that the improvement in the performance of the solar cell with the HQ-modified PEDOT:PSS was not due to a morphology change at the interface between the PEDOT:PSS and the active layer. In conducting AFM (C-AFM) measurements, which can probe local current levels, we found that the overall current level improved significantly in the HQ-modified PEDOT:PSS, as shown in Figures 5d

ACS Paragon Plus Environment

16

Page 17 of 45 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

and 5e. This C-AFM result is consistent with our previous results and confirms that the performance improvement in the solar cell with HQ-modified PEDOT:PSS resulted from enhancements to the charge transfer property between the PEDOT:PSS and the active layer.

CONCLUSION

In summary, we have enhanced the PCE of PTB7-Th:PC71BM BHJ solar cells by modifying the PEDOT:PSS surface with HQ. Although the band bending degree of PTB7-Th on the HQ-modified PEDOT:PSS was slightly larger than on pristine PEDOT:PSS, the HQ treatment lowered the hole transport barrier at the interface between the PEDOT:PSS and the active layer. In addition, because the HQ had a secondary doping effect, the sheet resistance of the PEDOT:PSS surface decreased by almost two orders of magnitude. IS studies clearly show reduced interfacial resistance after HQ treatment of the PEDOT:PSS surface. By lowering the hole transport barrier and reducing interfacial resistance, the HQ treatment nearly doubled the hole extraction

ACS Paragon Plus Environment

17

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 18 of 45

density calculated from the CE measurement. An increase in the current level of the HQ-modified PEDOT surface was also clearly seen in our C-AFM results. Thus, the device fabricated with HQ-modified PEDOT:PSS showed a 28% increase in efficiency compared to the device without HQ treatment. The best solar cell with HQ-modified PEDOT:PSS exhibited a maximum PCE of 10.18%. Modifying the PEDOT:PSS surface using an HQ solution is thus an easy way to effectively boost the performance of polymer solar cells.

EXPERIMENTAL SECTION

Device fabrication. ITO substrates were cleaned with detergent and ultrasonicated in acetone and IPA for 15 min each. A hole transport layer of PEDOT:PSS (Clevios PH) was spin-coated at 4000 rpm for 40 s after UV-ozone surface treatment and annealed at 150 °C for 10 min. The thickness of the PEDOT:PSS was 40–50 nm. Solutions with between 0.2 wt% and 2 wt% of HQ in IPA were spin-coated on top of the PEDOT:PSS layer at 5000 rpm for 40 s and annealed at 100 °C for 10 min. The substrates were then transferred to a N2-filled glovebox. The active layer solution was made with a 1:1.5 ratio

ACS Paragon Plus Environment

18

Page 19 of 45 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

of PTB7-Th and PC71BM in chlorobenzene with 3% DIO as a processing additive to get a better phase-separated morphology. The prepared solution was stirred overnight. The active layer was deposited on top of the PEDOT:PSS layer by spin-coating at 1000 rpm for 60 s and then annealed at 80 °C for 10 min. A ZnO nanoparticle solution (2.5 wt% in IPA) diluted to an IPA ratio of 1:10 was spin-coated at 3000 rpm for 30 s on top of the PTB7-Th:PC71BM layer as an electron transport layer, and it was then annealed at 80 °C for 10 min. Finally, 100 nm of aluminum was deposited by thermal evaporation at a vacuum condition of 2×10-6 Torr. The device area is 0.13 cm2.

Device characterization. The power conversion efficiencies of the organic solar cells were measured by J-V curves using a Keithley 2401 source measurement unit under AM 1.5G 100 mW/cm2 spectra from a solar simulator (Newport Co., Oriel). To calibrate the intensity of the solar simulator, a standard Si-photodiode detector with a KG-3 filter (Newport Co., Oriel) was used. The EQE was measured using a quantum efficiency measurement system solar cell spectral response/QE/IPCE (Newport Co., Oriel IQE200B). The light intensity at each wavelength was calibrated using a standard, single-

ACS Paragon Plus Environment

19

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 20 of 45

crystal Si photovoltaic cell. The absorption spectra of the device films were measured by a UV/Vis spectrophotometer (Varian, Cary5000).

The surface properties and morphologies of pristine PEDOT:PSS, HQ-modified PEDOT:PSS, and PTB7-Th:PC71BM films were characterized by AFM (NanoNavi II, SII Nano Technology Inc.) in the tapping mode. The current levels of the pristine PEDOT:PSS and HQ-modified PEDOT:PSS were measured using a C-AFM system (HITACHI NanoNavi E-Sweep) with +3V applied on the ITO bottom electrode under dark conditions. The pristine PEDOT:PSS film was fabricated by spin-coating PEDOT:PSS at 4000 rpm for 40 s on an ITO substrate, and the HQ-modified PEDOT:PSS film was further coated with 1 wt% HQ solution. IS measurements were taken using an impedance analyzer (IVIUM Tech., IviumStat) under dark conditions at an open circuit voltage in the frequency range between 0.1 Hz and 1.0 MHz. CE was conducted using the CE analyzer function of an organic semiconductor parameter test system (McScience T4000) under 1.0 sun at Voc conditions. To determine the valence band and work function of pristine PEDOT:PSS and HQ-modified PEDOT:PSS, UPS

ACS Paragon Plus Environment

20

Page 21 of 45 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

measurements were carried out with an ESCALAB 250-XI surface analysis system equipped with a He-discharge lamp providing He-I photons of 21.22 eV. The XPS investigation used a monochromatic Al-Kα X-ray gun with a photon energy of 1486.6 eV. The base vacuum pressure of the analysis system was ≈10-7 Torr. The Fermi edge was calibrated using a clean Au film, and all spectra presented were plotted with respect to the determined Fermi level. All XPS measurements were calibrated with reference to the Au 4f7/2 core level (83.98 eV) of a freshly deposited Au film. The measured samples were prepared by spin coating a PTB7-Th solution of 0.003 to 0.3 wt% on both pristine PEDOT:PSS and HQ-modified PEDOT:PSS films. The surface conductivity of pristine PEDOT:PSS and HQ-modified PEDOT:PSS was determined using a hall effect measurement system (Ecopia model No. HMS-5000). The thickness of the film was measured using a Dektak XT surface profiler. These samples were fabricated in the same way as the AFM samples. Mid-IR absorption spectra from pristine PEDOT:PSS and HQ-modified PEDOT:PSS were measured using an FTIR spectrometer (Varian, Varian 670). These samples were fabricated in the same way as the AFM samples, except ZnSe was used as the substrate.

ACS Paragon Plus Environment

21

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 22 of 45

ASSOCIATED CONTENT

Supporting Information.

The Supporting Information is available free of charge on the ACS Publications website at DOI: Experimental details on characterization and the results of device performances for other polymer devices; full UPS spectra of pristine PEDOT:PSS and modified PEDOT:PSS; external quantum efficiency (EQE) spectra; J-V characteristics of PTB7-Th:PC71BM solar cells with/without IPA surface treatment; J-V characteristics of P3HT:PCBM and PTB7:PC71BM solar cells; absorption spectra of PEDOT:PSS and PTB7-Th:PC71BM layer; contact-angle measurements; XPS spectra of PEDOT:PSS (PDF)

AUTHOR INFORMATION

Corresponding Author *E-mail: [email protected]

ORCID Shinuk Cho: 0000-0002-6855-833X

ACS Paragon Plus Environment

22

Page 23 of 45 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

Notes The authors declare no competing financial interest.

ACKNOWLEDGMENT This research was supported by a National Research Foundation of Korea grant (2017R1A2B4003583, 2014R1A4A1071686, 2017M2A2A6A01018599).

REFERENCES (1) Li, G.; Zhu, R.; Yang, Y. Polymer Solar Cell. Nat. Photonics 2012, 6, 153-161.

(2) Heeger, A. J. Bulk Heterojunction Solar Cells: Understanding the Mechanism of Operation. Adv. Mater. 2014, 26, 10-27.

(3) Brabec, C. J.; Sariciftci, N. S.; Hummelen, J. C. Plastic Solar Cells. Adv. Funct.

Mater. 2001, 11, 15-26.

(4) Li, M.; Gao, K.; Wan, X.; Zhang, Q.; Kan, B.; Xia, R.; Liu, F.; Yang, X.; Feng, H.; Ni, W.; Wang, Y.; Peng, J.; Zhang, H.; Liang, Z.; Yip, H.-L.; Peng, X.; Cao, Y.; Chen, Y.

ACS Paragon Plus Environment

23

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 24 of 45

Solution-Processed Organic Tandem Solar Cells with Power Conversion Efficiencies >12%. Nat. Photonics 2017, 11, 85-90.

(5) Kang, M. G.; Park, H. J.; Ahn, S. H.; Guo, L. J. Transparent Cu Nanowire Mesh Electrode on Flexible Substrates Fabricated by Transfer Printing and Its Application in Organic Solar Cells. Sol. Energ. Mater. Sol. Cells 2010, 94, 1179-1184.

(6) Yu, G.; Gao, J.; Hummelen, J. C.; Wudl, F.; Heeger, A. J. Polymer Photovoltaic Cells: Enhanced Efficiencies via a Network of Internal Donor-Acceptor Heterojunctions.

Science 1995, 270, 1789-1791.

(7) Zhao, W.; Li, S.; Yao, H.; Zhang, S.; Zhang, Y.; Yang, B.; Hou, J. Molecular Optimization Enables over 13% Efficiency in Organic Solar Cells. J. Am. Chem. Soc. 2017, 139, 7148-7151.

(8) Zhao, F.; Dai, S.; Wu, Y.; Zhang, Q.; Wang, J.; Jiang, L.; Ling, Q.; Wei, Z.; Ma, W.; You, W.; Wang, C.; Zhan, X. Single-Junction Binary-Blend Nonfullerene Polymer Solar Cells with 12.1% Efficiency. Adv. Mater. 2017, 29, 1700144.

ACS Paragon Plus Environment

24

Page 25 of 45 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

(9) Small, C. E.; Chen, S.; Subbiah, J.; Amb, C. M.; Tsang, S.-W.; Lai, T.-H.; Reynolds, J. R.; so, F. High-efficiency Inverted Dithienogermole-thienopyrrolodionebased Polymer Solar Cells. Nat. Photonics 2012, 6, 115-120.

(10) Son, H. J.; Carsten, B.; Jung, I. H.; Yu, L. Overcoming Efficiency Challenges in Organic Solar Cells: Rational Development of Conjugated Polymers. Energy Environ.

Sci. 2012, 5, 8158-8170.

(11) Lee, C.; Kang, H.; Lee, W.; Kim, T.; Kim, K. H.; Woo, H. Y.; Wang, C.; Kim, B. J. High‐Performance All‐Polymer Solar Cells Via Side‐Chain Engineering of the Polymer Acceptor: The Importance of the Polymer Packing Structure and the Nanoscale Blend Morphology. Adv. Mater. 2018, 27, 2466-2471.

(12) Chen, W.; Nikiforov, M. P.; Darling, S.B. Morphology Characterization in Organic and Hybrid Solar Cells. Energy Environ. Sci. 2012, 5, 8045-8074.

ACS Paragon Plus Environment

25

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 26 of 45

(13) Lee, J. K.; Ma, W. L.; Brabec, C. J.; Yuen, J.; Moon, J. S.; Kim, J. Y.; Lee, K.; Bazan, G. C.; Heeger, A.J. Processing Additives for Improved Efficiency from Bulk Heterojunction Solar Cells. J. Am. Chem. Soc. 2008, 130, 3619-3623.

(14) Lu, Z.; Jiang, B.; Zhang, X.; Tang, A.; Chen, L.; Zhan, C.; Yao, J. Perylene– Diimide Based Non-Fullerene Solar Cells with 4.34% Efficiency through Engineering Surface Donor/Acceptor Compositions. Chem. Mater. 2014, 26, 2907-2914.

(15) Yan, Y.; Cai, F.; Yang, L.; Li, J.; Zhang, Y.; Qin, F.; Xiong, C.; Zhou, Y.; Lidzey, D. G.; Wang, T. Polymer Solar Cells: Light‐Soaking‐Free Inverted Polymer Solar Cells with an Efficiency of 10.5% by Compositional and Surface Modifications to a Low‐Temperature‐Processed TiO2 Electron‐Transport Layer. Adv. Mater. 2017, 29, 1604044.

(16) Zhou, H.; Zhang, Y.; Seifter, J.; Collins, S. D.; Luo, C.; Bazan, G. C.; Nguyen, T.Q.; Heeger, A. J. High‐Efficiency Polymer Solar Cells Enhanced by Solvent Treatment.

Adv. Mater. 2013, 25, 1646-1652.

ACS Paragon Plus Environment

26

Page 27 of 45 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

(17) Nho, S.; Baek, G.; Park, S.; Lee, B. R.; Cha, M. J.; Lim, D. C.; Seo, J. H.; Oh, S.H.; Song, M. H.; Cho, S. Highly Efficient Inverted Bulk-Heterojunction Solar Cells with a Gradiently-Doped ZnO Layer. Energy Environ. Sci. 2016, 9, 240-246.

(18) Yu, Z.; Li, B.; Ouyang, J. Metal Ion/Dendrimer Complexes with Tunable Work Functions in a Wide Range and Their Application as Electron- and Hole-Transport Materials of Non-Fullerene Organic Solar Cells. Adv. Funct. Mat. 2018, 28, 1802554.

(19) Sun, Y.; Seo, J. H.; Takacs, C. J.; Seifter, J.; Heeger, A. J. Inverted Polymer Solar Cells Integrated with a Low‐Temperature‐Annealed Sol‐Gel‐Derived ZnO Film as an Electron Transport Layer. Adv. Mater. 2011, 23, 1679-1683.

(20) Li, S.-S.; Tu, K.-H.; Lin, C.-C.; Chen, C.-W.; Chhowalla, M. Solution-Processable Graphene Oxide as an Efficient Hole Transport Layer in Polymer Solar Cells. ACS

Nano, 2010, 4, 3169-3174.

(21) Zhou, Y.; Fuentes-Hernandez, C.; Shim, J.; Meyer, J.; Giordano, A. J.; Li, H.; Winget, P.; Papadopoulos, T.; Cheun, H.; Kim, J.; Fenoll, M.; Dindar, A.; Haske, W.;

ACS Paragon Plus Environment

27

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 28 of 45

Najafabadi, E.; Khan, T. M.; Sojoudi, H.; Barlow, S.; Graham, S.; Bredas, J.-L.; Marder, S. R.; Kahn, A.; Kippelen, B. A Universal Method to Produce Low–Work Function Electrodes for Organic Electronics. Science, 2012, 336, 327-332.

(22) Sun, Y.; Takacs, C. J.; Cowan, S. R.; Seo, J. H.; Gong, X.; Roy, A.; Heeger, A. J. Efficient, Air‐Stable Bulk Heterojunction Polymer Solar Cells Using MoOx as the Anode Interfacial Layer. Adv. Mater. 2011, 23, 2226-2230.

(23) Kim, J. Y.; Kim, S. H.; Lee, H.-H.; Ma, W.; Gong, X.; Heeger, A. J. New Architecture for High‐Efficiency Polymer Photovoltaic Cells Using Solution‐Based Titanium Oxide as an Optical Spacer. Adv. Mater. 2006, 18, 572-576.

(24) Gershon, T.; Metal Oxide Applications in Organic-Based Photovoltaics. Mater.

Sci. Technol. 2011, 27, 1357-1371.

(25) Liang, Z.; Zhang, Q.; Jiang, L.; Cao, G. ZnO Cathode Buffer Layers for Inverted Polymer Solar Cells. Energy Environ. Sci. 2015, 8, 3442-3476.

ACS Paragon Plus Environment

28

Page 29 of 45 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

(26) Yin, Z.; Wei, J.; Zheng, Q. Interfacial Materials for Organic Solar Cells: Recent Advances and Perspectives. Adv. Sci. 2016, 3, 1500362.

(27) Duarte, A.; Pu, K.-Y.; Liu, B.; Bazan, G. C. Recent Advances in Conjugated Polyelectrolytes for Emerging Optoelectronic Applications. Chem. Mater. 2011, 23, 501515.

(28) Seo, J. H.; Gutacker, A.; Sun, Y.; Wu, H.; Huang, F.; Cao, Y.; Scherf, U.; Heeger, A. J.; Bazan, G. C. Improved High-Efficiency Organic Solar Cells via Incorporation of a Conjugated Polyelectrolyte Interlayer. J. Am. Chem. Soc. 2011, 133, 8416-8419.

(29) Li, X.; Zhang, W.; Usman, K.; Fang, J. Small Molecule Interlayers in Organic Solar Cells. Adv. Energy Mater. 2018, 107, 1702730.

(30) Xue, Y.; Guo, P.; Yip, H.-L.; Li, Y.; Cao, Y. General Design of Self-Doped Small Molecules as Efficient Hole Extraction Materials for Polymer Solar Cells. J. Mater.

Chem. A 2017, 5, 3780-3785.

ACS Paragon Plus Environment

29

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 30 of 45

(31) Zhang, Q.; Wang, W.-T.; Chi, C.-Y.; Wächter, T.; Chen, J.-W.; Tsai, C.-Y.; Huang, Y.-C.; Zharnikov, M.; Tai, Y.; Liaw, D.-J. Toward a Universal Polymeric Material for Electrode Buffer Layers in Organic and Perovskite Solar Cells and Organic LightEmitting Diodes. Energy Environ. Sci. 2018, 11, 682-691.

(32) Cai, Y.; Chang, L.; You, L.; Fan, B.; Liu, H.; Sun, Y. Novel Nonconjugated Polymer as Cathode Buffer Layer for Efficient Organic Solar Cells. ACS Appl. Mater.

Interfaces 2018, 10, 24082-24089.

(33) Yip, H.-L.; Jen, A. K.-Y. Recent Advances in Solution-Processed Interfacial Materials for Efficient and Stable Polymer Solar Cells. Energy Environ. Sci. 2012, 5, 5994-6011.

(34) Hu, Z.; Zhang, J.; Hao, Z.; Zhao, Y. Influence of Doped PEDOT:PSS on the Performance of Polymer Solar Cells. Sol. Energy Mater. Sol. Cells 2011, 95, 27632767.

ACS Paragon Plus Environment

30

Page 31 of 45 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

(35) Brown, T. M.; Kim, J. S.; Friend, R. H.; Cacialli, F. Built-In Field Electroabsorption Spectroscopy of Polymer Light-Emitting Diodes Incorporating a Doped Poly(3,4ethylene dioxythiophene) Hole Injection Layer. Appl. Phys. Lett. 1999, 75, 1679-1681.

(36) Dupont, S. R.; Oliver, M.; Krebs, F. C.; Dauskardt, R. H. Interlayer Adhesion in Roll-to-Roll Processed Flexible Inverted Polymer Solar Cells. Sol. Energy Mater. Sol.

Cells 2012, 97, 171-175.

(37) Yu, D.; Oyewole, O. K.; Kwabi, D.; Tong, T.; Anye, V. C.; Asare, J.; Rwenyagila, E.; Fashina, A.; Akogwu, O.; Du, J.; Soboyejo, W. O. Adhesion in Flexible Organic and Hybrid Organic/Inorganic Light Emitting Device and Solar Cells. J. Appl. Phys. 2014,

116, 074506.

(38) Arias, A. C.; Granstrom, M.; Thomas, D. S.; Petritsch, K.; Friend, R. H. Doped Conducting-Polymer–Semiconducting-Polymer Interfaces: Their Use in Organic Photovoltaic Devices. Phys. Rev. B 1999, 60, 1854-1860.

ACS Paragon Plus Environment

31

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 32 of 45

(39) Lee, B. R.; Jung, E. D.; Nam, Y. S.; Jung, M.; Park, J. S.; Lee, S.; Choi, H.; Kim, S.-J.; Shin, N. R.; Kim, Y.-K.; Kim, S. O.; Kim, J. Y.; Shin, H.-J.; Cho, S.; Song, M. H. Amine-Based Polar Solvent Treatment for Highly Efficient Inverted Polymer Solar Cells.

Adv. Mater. 2014, 26, 494-500.

(40) Fu, P.; Guo, X.; Zhang, B.; Chen, T.; Qin, W.; Ye, Y.; Hou, J.; Zhang, J.; Li, C. Achieving 10.5% Efficiency for Inverted Polymer Solar Cells by Modifying the ZnO Cathode Interlayer with Phenols. J. Mater. Chem. A 2016, 4, 16824-16829.

(41) Park, M.-H.; Li, J.-H.; Kumar, A.; Li, G.; Yang, Y. Doping of the Metal Oxide Nanostructure and its Influence in Organic Electronics. Adv. Funct. Mater. 2009, 19, 1241-1246.

(42) Liao, S.-H.; Jhuo, H.-J.; Yeh, P.-N.; Cheng, Y.-S.; Li, Y.-L.; Lee, Y.-H.; Sharma, S.; Chen, S.-A. Single Junction Inverted Polymer Solar Cell Reaching Power Conversion Efficiency 10.31% by Employing Dual-doped Zinc Oxide Nano-film as Cathode Interlayer. Sci. Rep. 2014, 4, 6813.

ACS Paragon Plus Environment

32

Page 33 of 45 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

(43) Jagadamma, L. K.; Al-Senani, M.; El-Labban, A.; Gereige, I.; Ndjawa. G. O. N.; Faria, J. C. D.; Kim, T.; Zhao, K.; Cruciani, F.; Anjum, D. H.; McLachlan, M. A.; Beaujuge, P. M.; Amassian, A. Polymer Solar Cells with Efficiency >10% Enabled via a Facile Solution‐Processed Al‐Doped ZnO Electron Transporting Layer. Adv. Energy

Mater. 2015, 5, 1500204.

(44) Kim, J. H.; Liang, P.-W.; Williams, S. T.; Cho, N.; Chueh, C.-C.; Glaz, M. S.; Ginger, D. S.; Jen, A. K.-Y. High-Performance and Environmentally Stable Planar Heterojunction Perovskite Solar Cells Based on a Solution-processed Copper-doped Nickel Cxide Hole-Transporting Layer. Adv. Mater. 2015, 27, 695-701.

(45) Xie, C.; Chen, L.; Chen, Y. Electrostatic Self-Assembled Metal Oxide/Conjugated Polyelectrolytes as Electron-Transporting Layers for Inverted Solar Cells with High Efficiency. J. Phys. Chem. C 2013, 117, 24804-24814.

(46) Choi, H.; Park, J. S.; Jung, E.; Kim, G.-H.; Lee, B. R.; Kim, S. O.; Song, M. H.; Woo, H. Y.; Kim, J. Y. Combination of Titanium Oxide and a Conjugated Polyelectrolyte

ACS Paragon Plus Environment

33

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 34 of 45

for High‐Performance Inverted‐Type Organic Optoelectronic Devices. Adv. Mater. 2011,

23, 2759-2763.

(47) Liu, D.; Li, Y.; Yuan, J.; Hong, Q.; Shi, G.; Yuan, D.; Wei, J.; Huang, C.; Tang, J.; Fung, M.-K. Improved Performance of Inverted Planar Perovskite Solar Cells with F4TCNQ Doped PEDOT:PSS Hole Transport Layers. J. Mater. Chem. A 2017, 5, 57015708.

(48) Li, X.-Y.; Zhang, L.-P.; Tang, F.; Bao, Z.-M.; Lin, J.; Li, Y.-Q.; Chen, L.; Ma, C.-Q. The Solvent Treatment Effect of the PEDOT:PSS Anode Interlayer in Inverted Planar Perovskite Solar Cells. RSC Adv. 2016, 6, 24501-24507.

(49) Song, C.; Zhong, Z.; Hu, Z.; Wang, J.; Wang, L.; Ying, L.; Wang, J.; Cao, Y. Methanol Treatment on Low-Conductive PEDOT: PSS to Enhance the PLED's Performance. Org. Elec. 2016, 28, 252-256.

ACS Paragon Plus Environment

34

Page 35 of 45 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

(50) Liu, H.; Li, X.; Zhang, L.; Hong, Q.; Tang, J.; Zhang, A.; Ma, C.-Q. Influence of the Surface Treatment of PEDOT:PSS Layer with High Boiling Point Solvent on the Performance of Inverted Planar Perovskite Solar Cells. Org. Elec. 2017, 47, 220-227.

(51) Xing, W.; Chen, Y.; Wu, X.; Xu, X.; Ye, P.; Zhu, T.; Guo, Q.; Yang, L.; Li, W.; Huang, H. PEDOT:PSS‐Assisted Exfoliation and Functionalization of 2D Nanosheets for High‐Performance Organic Solar Cells. Adv. Funct. Mater. 2017, 27, 1701622.

(52) Cao, B.; He, X.; Fetterly, C. R.; Olsen, B. C.; Luber, E. J.; Buriak, J. M. Role of Interfacial Layers in Organic Solar Cells: Energy Level Pinning versus Phase Segregation. ACS Appl. Mater. Interfaces 2016, 8, 18238-18248.

(53) Zhang, W.; Zhao, B.; He, Z.; Zhao, X.; Wang, H.; Yang, S.; Wu, H.; Cao, Y. HighEfficiency ITO-Free Polymer Solar Cells Using Highly Conductive PEDOT:PSS/Surfactant Bilayer Transparent Anodes. Energy Environ. Sci. 2013, 6, 1956-1964.

ACS Paragon Plus Environment

35

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 36 of 45

(54) Guerrero, A.; Marchesi, L. F.; Boix, P. P.; Ruiz-Raga, S.; Ripolles-Sanchis, T.; Garcia-Belmonte, G.; Bisquert, J. How the Charge-Neutrality Level of Interface States Controls Energy Level Alignment in Cathode Contacts of Organic Bulk-Heterojunction Solar Cells. ACS Nano 2012, 6, 3453-3460.

(55) Boix, P. P.; Ajuria, J.; Etxebarria, I.; Pacios, R.; Garcia-Belmonte, G.; Bisquert, J. Role of ZnO Electron-Selective Layers in Regular and Inverted Bulk Heterojunction Solar Cells. J. Phys. Chem. Lett. 2011, 2, 407-411.

(56) Bisquert, J.; Garcia-Belmonte, G. On Voltage, Photovoltage, and Photocurrent in Bulk Heterojunction Organic Solar Cells. J. Phys. Chem. Lett. 2011, 2, 1950-1964.

(57) Cho, S.; Park, S. H.; Lee, K. Reflectance Study on the Metal-Insulator Transition Driven by Crystallinity Change in Poly(3,4-ethylenedioxy thiophene)/Poly(styrenesulfonate) Films. J. Koean Phys. Soc. 2005, 47, 474-478.

(58) Xu, B.; Gopalan, S.-A.; Gopalan, A.-L.; Muthuchamy, N.; Lee, K.-P.; Lee, J.-S.; Lee, S.-W.; Kim, S.-W.; Kim, J.-S.; Joeng, H.-M.; Kwon, J.-B.; Bae, J.-H.; Kang, S.-W.

ACS Paragon Plus Environment

36

Page 37 of 45 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

Functional Solid Additive Modified PEDOT:PSS as an Anode Buffer Layer for Enhanced Photovoltaic Performance and Stability in Polymer Solar Cells. Sci. Rep. 2017, 7, 45079.

(59) Lenze, M. R.; Kronenberg, N. M.; Wurthner, F.; Meerholz, K. In-situ Modification of PEDOT: PSS Work Function Using Alkyl Alcohols as Secondary Processing Solvents and Their Impact on Merocyanine Based Bulk Heterojunction Solar Cells. Org. Elec. 2015, 21, 171-176.

(60) Bisquert, J.; Mora-Sero, I.; Fabregat-Santiago, F. Diffusion–Recombination Impedance Model for Solar Cells with Disorder and Nonlinear Recombination. Chem.

Electro. Chem. 2014, 1, 289-296.

(61) Gonzalez-Pedro, V.; Juarez-Perez, E. J.; Arsyad, W.-S.; Barea, E. M.; FabregatSantiago, F.; Mora-Sero, I.; Bisquert, J. General Working Principles of CH3NH3PbX3 Perovskite Solar Cells. Nano Lett. 2014, 14, 888-893.

ACS Paragon Plus Environment

37

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 38 of 45

(62) Crispin, X.; Jakobsson, F. L. E.; Crispin, A.; Grim, P. C. M.; Andersson, P.; Volodin, A.; van Haesendonck, C.; Van der Auweraer, M.; Salaneck, W. R.; Berggren, M. The Origin of the High Conductivity of Poly(3,4ethylenedioxythiophene)−Poly(styrenesulfonate) (PEDOT−PSS) Plastic Electrodes.

Chem. Mater. 2006, 18, 4354-4360.

(63) Quyang, J. “Secondary Doping” Methods to Significantly Enhance the Conductivity of PEDOT:PSS for Its Application as Transparent Electrode of Optoelectronic Devices. Displays 2013, 34, 423-436.

(64) McGillivray, D.; Thomas, J. P.; Abd-Ellah, M.; Heinig, N. F.; Leung, K. T. Performance Enhancement by Secondary Doping in PEDOT:PSS/Planar-Si Hybrid Solar Cells. ACS Appl. Mater. Interfaces 2016, 8, 34303-34308.

(65) Donoval, M.; Micjan, M.; Novota, M.; Nevrela, J.; Kovacova, S.; Pavuk, M.; Juhasz, P.; Jegalka, M.; Kovac Jr., J.; Jakabovic, J.; Cigan, M.; Weis, M. Relation Between Secondary Doping and Phase Separation in PEDOT: PSS Films. Appl. Surf.

Sci. 2017, 395, 86-91.

ACS Paragon Plus Environment

38

Page 39 of 45 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

(66) Wang, M.; Zhou, M.; Zhu, L.; Li, Q.; Jiang, C. Enhanced polymer solar cells efficiency by surface coating of the PEDOT: PSS with polar solvent. Solar Energy 2016,

129, 175-183.

(67) Kvarnstrom, C.; Neugebauer, H.; Ivaska, A.; Sariciftci, N.S. Vibrational Signatures of Electrochemical P- and N-Doping of Poly(3,4-ethylenedioxythiophene) Films: An In-situ Attenuated Total Reflection Fourier Transform Infrared (ATR-FTIR) Study. J. mol. Struct. 2000, 521, 271-277.

ACS Paragon Plus Environment

39

ACS Applied Materials & Interfaces

(b)

(a)

3.8 3.9

PTB7-Th PC71BM

PTB7-Th

E (eV)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 40 of 45

Al

OMe

O

4.95

ITO Hydroquinone (HQ)

4.2

HQ modified PEDOT:PSS

5.3 5.9 PC71BM

ZnO NPs

Figure 1. (a) Schematic illustration of the device structure and chemical structure of the photoactive materials (donor: PTB7-Th, acceptor: PC71BM) and hydroquinone (HQ) surface modifier for PEDOT:PSS, (b) Energy level diagram of a BHJ solar cell based on a PTB7Th:PC71BM blend.

Figure 2. (a) J-V characteristics of PTB7-Th:PC71BM solar cells with pristine PEDOT:PSS and PEDOT:PSS modified with various ratios of HQ. (b) Jsc, (c) Voc, and (d) PCE distributions for the solar cells with pristine PEDOT:PSS and PEDOT:PSS modified with various ratios of HQ. The data were obtained from 20 devices for each case.

ACS Paragon Plus Environment

40

Page 41 of 45 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

Table 1. Summarized device performance characteristics of PTB7-Th:PC71BM solar cells with pristine PEDOT:PSS and PEDOT:PSS modified with various amounts of HQ. HQ

Voc

Jsc

Jsc-EQE§

η

ηave*

(V)

(mA/cm2)

(mA/cm2)

(%)

Pristine

0.782

15.6

15.4

0.654

HQ 0.2wt%

0.798

16.8

15.7

HQ 0.4wt%

0.795

17.6

HQ 0.6wt%

0.792

HQ 0.8wt%

(%)

Rs (Ω/cm2)

Rsh (Ω/cm2)

7.98

7.87

4.03

509

0.658

8.82

8.63

4.33

372

16.2

0.657

9.19

9.06

3.95

339

18.1

16.3

0.649

9.30

9.23

3.81

347

0.796

18.6

17.1

0.681

10.1

9.95

4.01

477

HQ 1.0wt%

0.793

18.9

17.4

0.680

10.2

10.1

3.81

518

HQ 1.5wt%

0.779

18.5

17.1

0.639

9.21

9.16

3.31

382

HQ 2.0wt%

0.781

17.9

16.4

0.611

8.54

8.48

3.84

251

concentration

FF

*Average PCE values were obtained from 20 devices. §

Jsc values calculated from EQE measurements.

ACS Paragon Plus Environment

41

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 42 of 45

Figure 3. Secondary electron cut-off and HOMO onset UPS spectra of (a) pristine PEDOT:PSS and (b) HQ-modified PEDOT:PSS with increasing concentrations of PTB7-Th. The XPS spectra for S 2p and C 1s of (c) pristine PEDOT:PSS and (d) HQ-modified PEDOT:PSS with increasing concentrations of PTB7-Th. Schematic energy-level diagrams of PTB7-Th on (e) pristine PEDOT and (f) HQ-modified PEDOT:PSS. The energy unit is eV. (EF: Fermi energy level, Evac: Vacuum level, Δ: Interfacial dipole, IP: Ionization potential, Vb: Energy level relaxation, φe: Electron injection barrier, φh: Hole injection barrier).

ACS Paragon Plus Environment

42

Page 43 of 45

1

(a) 100

(b)

Pristine PEDOT:PSS HQ modified PEDOT:PSS

-Z'' (k )

2

J sc (mA/cm )

10 -1 10 -2 10 -3 10 -4 10 -5 10 -6 10 -7 10 -8 10 -1.0

-0.5

0.0

0.5

1.0

1.5

2.0

1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0.0

Pristine PEDOT:PSS HQ modified PEDOT:PSS

C2

(c)

40 30

R3

R2

0.5

1.0

1.5

2.0

Z' (k )

2.5

3.0

11

8x10

(d) 7x1011 -2

n ext (cm )

35 25 20 15

11

6x10

11

5x10

11

4x10

11

3x10

11

10

2x10

Pristine PEDOT:PSS HQ modified PEDOT:PSS

5 0 0

C3

R1

Voltage (V)

Current (mA)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

1

2

3

4

Time (s)

5

11

1x10 6

0 0

2

4

6

Time (s)

8

10

Figure 4. (a) Dark J-V characteristics of PTB7-Th:PC71BM solar cells with pristine PEDOT:PSS and HQ-modified PEDOT:PSS. (b) Nyquist plot of impedance spectroscopy measurements at

Voc under light irradiation and the corresponding equivalent circuit model. (c) CE current transient under 1 sun Voc conditions. (d) Calculated charge extraction density from the CE measurements.

ACS Paragon Plus Environment

43

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 44 of 45

Figure 5. (a) FTIR absorption spectra of IRAV modes in mid-IR region in pristine PEDOT:PSS and HQ-modified PEDOT:PSS. AFM topo images of (b) pristine PEDOT:PSS and (c) HQmodified PEDOT:PSS. C-AFM images of (d) pristine PEDOT:PSS and (e) HQ-modified PEDOT:PSS on an ITO substrate in the dark at +3V.

Table 2. Conductivity and sheet resistance of pristine PEDOT:PSS and HQ-modified PEDOT:PSS.

Pristine PEDOT:PSS

Thickness

Conductivity

Sheet Resistance

(nm)

(Ω-1cm-1)

(kΩ/□)

52.5

0.18

1,340

(±1.35×10-3)

(±9.87)

ACS Paragon Plus Environment

44

Page 45 of 45 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

HQ-modified PEDOT:PSS

51.7

3.38

59.1

(±5.17×10-3)

(±0.92)

ToC figure

ACS Paragon Plus Environment

45