Wettability Alteration of Quartz Surface by Low ... - ACS Publications

Jul 1, 2019 - BOC Gas. ≥0.99. Table 3. Compositional Data of the Substrate from Energy-. Dispersive Spectroscopy element atomic composition [%]...
1 downloads 0 Views 868KB Size
Article Cite This: Energy Fuels 2019, 33, 7062−7068

pubs.acs.org/EF

Wettability Alteration of Quartz Surface by Low-Salinity Surfactant Nanofluids at High-Pressure and High-Temperature Conditions Nilesh Kumar Jha,†,‡ Muhammad Ali,†,§ Stefan Iglauer,§ Maxim Lebedev,† Hamid Roshan,⊥ Ahmed Barifcani,† Jitendra S. Sangwai,*,‡ and Mohammad Sarmadivaleh†

Downloaded via UNIV OF CAMBRIDGE on August 20, 2019 at 09:02:22 (UTC). See https://pubs.acs.org/sharingguidelines for options on how to legitimately share published articles.



Western Australian School of Mines (WASM): Minerals, Energy and Chemical Engineering, Curtin University, 26 Dick Perry Avenue, Kensington, Western Australia 6151, Australia ‡ Petroleum Engineering Program, Department of Ocean Engineering, Indian Institute of Technology Madras, Chennai, Tamil Nadu 600036, India § School of Engineering, Edith Cowan University, 270 Joondalup Drive, Joondalup, Western Australia 6027, Australia ⊥ School of Minerals and Energy Resources Engineering, UNSW Sydney, Sydney, New South Wales 2052, Australia ABSTRACT: Advanced low-salinity aqueous formulations have shown promising results for rock wettability modification and interfacial tension reduction. Additives, such as surfactant and nanoparticles, can be used for such formulations. The interaction of these novel formulations with different fluid phases and the rock surface is, however, yet to be understood in detail. Thus, an experimental study was conducted in this study to investigate the interfacial tension and wettability of carbon dioxide and anionic surfactant (SDBS, 1.435 mM) at high pressure and temperature. The results show that the anionic surfactant (SDBS, 1.435 mM) augmented the effect of zirconia (ZrO2) nanoparticles (100−2000 mg/L concentration) at low-salinity conditions and proved to be an effective wettability and interfacial tension modifier when used at appropriate divalent cation/sulfate ion ratios. Low-salinity surfactant nanofluids may thus be applied for wettability alteration and interfacial tension reduction for recovering residual oil, carbon dioxide-enhanced oil recovery, as well as carbon dioxide geosequestration. We also demonstrate in this study that the ratio of divalent cations to sulfate ions (0 ≤ M2+/SO42−≤ 4.427) has a significant role in interfacial tension reduction and wettability modification. We further show using contact angle wettability measurements that initial weak water− wet quartz surfaces can turn to more water−wet when zirconia nanoparticles used in the low-salinity formulation are in the range of 100−1000 mg/L. Interestingly, further incremental nanoparticle concentration decreases the water wettability but further reduces the carbon dioxide/brine interfacial tension.

1. INTRODUCTION Low-salinity water injection has emerged as a new enhanced oil recovery technique, and it is often considered as a costeffective and environmentally friendly oil recovery method.1−3 The importance of the technique is evidently more highlighted with the decline in conventional resources and the need for efficient tertiary recovery methods.4−6 One of the areas of interest is the use of additives such as surfactants or nanoparticles in combination with low-salinity water to enhance its performance.2,3,7−11 Besides implications of these techniques in CO2-enhanced oil recovery,12−15 they can be used for CO2 geosequestration16−19 and hybrid water alternating gas injection (WAG) processes.20,21 It has been observed that the presence of ionic species (such as Ca2+, Na2+, Mg2+, HCO3−, SO42−)13,22−27 can play an important role in oil recovery by low-salinity water injection. The mechanisms are essentially linked to interfacial tension (IFT) reduction, electric double-layer expansion, fines migration, multi-ion exchange (MIE), and pH increase.1 While some studies showed that the concentration of divalent and monovalent cations in low-salinity aqueous solutions could affect IFT between oil and water in a unique way depending on their ratio,23 others argued that cation bridging takes place and alters the wettability of the rock surface as the predominant mechanism.3,28 Wettability of geological minerals and its effect © 2019 American Chemical Society

on the CO2 trapping process during geosequestration is also highly affected by physiochemical interactions of CO2 and brine.29 Wettability of rock surfaces in an aqueous/nonaqueous (oleic)/rock three-phase system is related to the hydrophilicity or hydrophobicity of the aqueous phase and its preference to cover or not to cover the rock surface.30,31 Table 1 presents the wettability classification of the aqueous phase-rock system used in this study.31 Electric double-layer expansion (DLVO theory)32 is also supposed to increase the rock surface water wetness by providing a stable water film.33 For DLVO theory to be effective, however, the oil layer needs to be continuous, Table 1. Wettability Based on Contact Angle of Aqueous Phase-Rock System wettability state

water contact angle θ (deg)

complete water−wet strongly water−wet weakly water−wet intermediate water−wet

0 0−50 50−70 70−100

Received: April 9, 2019 Revised: June 25, 2019 Published: July 1, 2019 7062

DOI: 10.1021/acs.energyfuels.9b01102 Energy Fuels 2019, 33, 7062−7068

Article

Energy & Fuels

The composition of the quartz plate, Table 3, was measured by the energy-dispersive spectroscopy (EDS) technique using a scanning electron microscope (Phenom XL, Netherlands).

which may not be the case of residual oil in rock pores, i.e., where it exists in blobs nonuniformly distributed in microporous space.1,34,35 Divalent cations and SO42− are known to build the most viscoelastic oil−water interfaces as compared to other ions and are favorable to oil recovery.27 Interestingly though, the role of these ions in wettability alteration resulting in detachment of polar species from the sandstone rock surface could not be explained. The role of SO42− in oil recovery has been investigated for carbonate, chalk, and dolomite reservoirs;1 however; sandstone chemistry has rarely been investigated. Moreover, the divalent cation to SO42− ratio can play a key role in the adsorption of anionic surfactant and surfactant augmented nanoparticles by the clay-bound rock surface, thus affecting the wettability of sandstone surfaces.3 We further observed the role of cations in cation bridging contributing toward physicochemical interactions between different negatively charged species by rendering all of the surface negatively charged using high pH.3 The major contribution toward the adsorption of surfactants is known to be affected by the presence of 1:136,37 and 2:1 dioctahedral clay minerals.3 In spite of recent efforts, there is a considerable lack of experimental data and understanding of the physical phenomena affecting the macroscale processes. In this study, we therefore to investigate in detail the role of the divalent cations to SO42− ratio on the wettability alteration of weak water−wet quartz surfaces by low-salinity sodium dodecylbenzenesulfonate (SDBS, 1.435 mM),8 augmented ZrO2 (0−2000 mg/L)38 nanofluids at high pressure (20 MPa) and temperature (70 °C) conditions in the presence of CO2.

Table 3. Compositional Data of the Substrate from EnergyDispersive Spectroscopy

2.1. Materials. Sodium chloride (NaCl, ≥99% mass fraction) and sodium sulfate (Na2SO4, ≥99% mass fraction) were used as monovalent background salts, and calcium chloride (CaCl2, ≥99% mass fraction) and magnesium sulfate (MgSO4, ≥99% mass fraction) were used as divalent background salts. The anionic surfactant used in the study was sodium dodecylbenzenesulfonate (SDBS, ≥99% mass fraction), and decane (99% mass fraction purity) was used as an oleic phase. Zirconium dioxide nanoparticles (ZNPs) (average particle size ≤ 100 nm) were also used to prepare the nanofluids. Aqueous solutions of individual salts and surfactants were prepared using ultrapure water of 17.65 MΩ cm resistivity. Table 2 provides the list of chemicals used in this study.

Table 2. List of Chemicals Used in This Study

chemical sodium chloride (NaCl) calcium chloride (CaCl2) magnesium sulfate (MgSO4) sodium sulfate (Na2SO4) zirconium dioxide nanopowder (ZrO2) SDBS decane Carbon dioxide

supplier

CAS no.

≥0.99

7647-14-5

Rowe Scientific, Western Australia, Australia Rowe Scientific, Western Australia, Australia Merck, Australia

≥0.99

10043-52-4

≥0.99

7487-88-9

Merck, Australia

≥0.99

7757-82-6

Merck, Australia

≥0.99

1314-23-4

Merck, Australia Merck, Australia BOC Gas

≥0.99 ≥0.99 ≥0.99

25155-30-0 124-18-5

atomic composition [%]

weight composition [%]

68.29 17.35 9.23 1.93 0.98

52.67 23.49 10.23 2.26 1.89

2.2. Method. All salt solutions were prepared gravimetrically using an analytical balance (CP224S, Sartorius AG, Germany) with repeatability of ≤0.1 mg (standard deviation). The aqueous phase solutions were prepared using a magnetic stirrer at 400−600 rpm at 20 °C, Table 4. High-salinity brine (HSW) was prepared and later diluted 10 times to make low-salinity brine (LSW1). Later, brines with lower salinity (LSW2, LSW3, and LSW4) were prepared with ultrapure water. Furthermore, the low-salinity brines containing SDBS (1.435 mM) were prepared and onward from here labeled as lowsalinity surfactants as LSS1, LSS2, LSS3, and LSS4, respectively. Lowsalinity surfactants were used to prepare 12 combinations of nanofluids with 100, 1000, and 2000 mg/L ZNPs using ultrasonication (300VT Ultrasonic Homogenizer/BIOLOGICS, using a sonication power of 240 W); each batch was sonicated for 4 periods of 15 min with 5 min rest to avoid overheating.39,40 Quartz samples were cleaned with deionized water, acetone, and methanol and then using air plasma to remove all organic and inorganic contaminations.31 These samples were then aged in decane for 3 weeks at 20 °C and atmospheric pressure. Quartz samples were then air dried for 15 min using pressurized pure air before contact angle measurements. The unique surface behavior and physicochemical properties depending on chain length make alkanes suitable candidates for wetting and 2-dimensional ordering studies.41 Table 5 gives the compositions of the prepared aqueous solutions with and without ZNPs used in this study. 2.1.1. Contact Angle and Interfacial Tension Measurements. Wettability measurements were carried out at reservoir conditions (i.e., 70 °C at 20 MPa) by the contact angle method using a tilted plate goniometric setup.42−44 The setup consisted of a cell designed to operate at high-pressure and high-temperature conditions. A stage tilted at an angle of 17° was placed inside the cell to hold the substrate.44 Two separate high-precision syringe pumps (Teledyne D500, pressure accuracy of 0.1%) were used to adjust the CO2 pressure and to drive (using deionized water) the low-salinity surfactant solutions. At the pressure and temperature maintained in this study, CO2 is in supercritical phase (scCO2). The aged substrate was placed on the stage inside the cell and heated to 70 °C, and the CO2 pressure was then raised to 20 MPa. Subsequently, a droplet (average volume of 6 ± 1 μL) of low-salinity surfactant solutions was dispensed onto the quartz surface through a needle.42 The advancing (θa, at the leading edge) and receding (θr, at trailing edge) contact angles of the droplet were then measured as soon as the drop started to move.62 This process was filmed using a high-resolution video camera (Basler scA 640-70 fm, pixel size = 7.4 μm; frame rate = 71 fps; Fujinon CCTV lens: HF35HA1B; 1:1.6/35 mm), and images were extracted to obtain θa and θr.42 The standard deviation of the measurements was ±3° based on replicated measurements.42 We use the pendant drop method for measuring the interfacial tension (IFT) of low-salinity surfactant nanofluids in the presence of CO2. Image analysis of the captured image of a pendant drop for IFT calculations was carried out by drop profile fitting using the pendant drop plugin of ImageJ software.45

2. MATERIALS AND METHODS

purity (mass fraction)

element oxygen silicon sodium magnesium calcium

7063

DOI: 10.1021/acs.energyfuels.9b01102 Energy Fuels 2019, 33, 7062−7068

Article

Energy & Fuels Table 4. Compositions of the Brines brine

Na+ [mg/L]

Ca2+ [mg/L]

Mg2+ [mg/L]

Cl− [mg/L]

SO42− [mg/L]

M2+/SO4−

HSW LSW1 LSW2 LSW3 LSW4

11 494.9 1149.5 1207.7 1252.8 1271.6

601.2 60.1 37.1 11 0

36.5 3.6 0 0 0

18 790.1 1879.0 1928.1 1951.4 1961.0

144.1 14.4 14.4 14.4 14.4

4.424 4.424 2.576 0.764 0.000

makes them suitable for counterion binding from available negatively charged species including the negatively charged headgroup of an anionic surfactant. Anionic surfactant headgroups are also exposed to counterion binding by cations having high charge density. Allen et al. explained that the cations having high charge density (i.e., smaller and highly charged) are more hydrated and reluctant to bind to the surfactant headgroup or the mineral surface.48 On the other hand, a hydration effect was proposed to be only significant when the valency of two ions (such as Ca2+ and Mg2+) are the same, mostly on account of immature understanding of this effect.48 Dugyala et al. investigated the role of electrostatic interactions in the adsorption kinetics of nanoparticles at fluid−fluid interfaces.49 They found that the water/decane IFT decrease was higher when the particles were weakly charged as higher numbers of particles adsorbed to the interface, which was attributed to image charge effect.49 With their model using modified Ward and Tordai theory,50 they showed that the effective diffusivity of the particles is determined by their energy barrier when the particles approach near the interface.49 A high net energy barrier prevents the adsorption of particles to the interface when the particles are highly charged which can be resolved with screening the particles by salt addition.49 We similarly postulate that the measured IFT in this study is also based on the availability of positively charged species (Ca2+, Mg2+) for binding with either the headgroup of SDBS or other negatively charged species (SO42−). The headgroup of SDBS and/or SO42− may get attached to the ZNPs surface, Figure 2, and contribute toward the effective diffusivity and

Table 5. Compositions of the Nanofluids LSS LSS1 LSS2 LSS3 LSS4

ZNP [0 mg/L] LSS1 LSS2 LSS3 LSS4

+ + + +

0% 0% 0% 0%

ZNP [100 mg/L] LSS1 LSS2 LSS3 LSS4

+ + + +

0.01% 0.01% 0.01% 0.01%

ZNP [1000 mg/L]

ZNP [2000 mg/L]

LSS1 LSS2 LSS3 LSS4

LSS1 LSS2 LSS3 LSS4

+ + + +

0.1% 0.1% 0.1% 0.1%

+ + + +

0.2% 0.2% 0.2% 0.2%

3. RESULTS AND DISCUSSION 3.1. Effect of ZNP Concentration on IFT of LowSalinity Surfactant Nanofluids. Figure 1 shows the

Figure 1. Experimental values for LSS nanofluid/scCO2 IFT against the ZNP concentration: (red circle) LSS1, (yellow circle) LSS2, (green circle) LSS3, and (blue circle) LSS4.

experimental data on IFT of low-salinity surfactant nanofluids as a function of ZNP concentration. From this figure, it is seen that the IFT decreases with increase in ZNP concentration for LSS1. For LSS2, LSS3, and LSS4; however, IFT increases with the ZNP increase. Thus, it is observed that there is a reversal in the IFT trend between LSS1 and LSS2/LSS3/LSS4 with an increase in ZNP concentration. Interestingly, for LSS2, LSS3, and LSS4, IFT values at approximately 100 mg/L of ZNP concentration are very close to each other. Considering LSS2/LSS3/LSS4, it is observed that for higher ZNPs concentrations (>100 mg/L ZNP) the IFT change depends more on the change in the ratio of divalent cations to sulfate ions than on a change in ZNPs concentration isoelectric point (IEP) of ZNPs is at pH 6.46 Any pH above and below this IEP affects the average particle size (large cluster of nanoparticles of equivalent diameter 100−1600 nm formed from individual ZrO2 particles of diameter 20−30 nm).46 Because CO2 dissolution and reaction with the water acidifies (pH < 3) the aqueous phase,47 the zeta potential of ZNPs is slightly positive (rendering them weakly positively charged).46 In the acidic condition (pH < 3), the average particle size of ZNPs is 100 nm.46 The charge associated with the ZNPs

Figure 2. Schematic of nanoaggregate adsorption at the nanofluid/ scCO2 interface.

enhance the availability of nanoaggregates at the interface to reduce IFT. However, the formed nanoaggregates can also have an effective net charge which might be responsible for IFT increase in other cases as seen for LSS2, LSS3, and LSS4. In the case of LSS1 (containing highest amount of divalent cations), more divalent cations are available for binding to the headgroup of the surfactant or SO42− and prevents them from adsorbing to the weakly positively charged ZNP surface. An increase in the concentration of nanoparticles decreases the IFT as more of them adsorb at the fluid−fluid interface. In 7064

DOI: 10.1021/acs.energyfuels.9b01102 Energy Fuels 2019, 33, 7062−7068

Article

Energy & Fuels

3.3. Effect of ZNP Concentration on the Contact Angle of Low-Salinity Surfactant Nanofluids. The consistencies in the data based on replicate measurements and their trend represent weak or intermediate water wetness of the quartz substrate due to aging in decane, followed by drying in compressed pure air and brief heating (before CO2 loading). Alkane molecules adsorbed to the silica surface can interact directly with the surface and adjacent adsorbed molecules.51 The interface formed between nonpolar alkane solvents and hydrophilic silica interfaces is polar.51 Earlier gravimetric studies of medium-length (C6− C12) alkane adsorption onto silica particles showed a linear relationship between the amount of alkane adsorbed and the relative alkane partial pressure.52,53 This linear dependency implies monolayer adsorption (not multilayer; i.e., a thin liquid film).51 A brief heating of the substrate at 70 °C in the IFT chamber before CO2 loading elevates the vapor pressure of adsorbed n-decane to 3.4 × 10−3 MPa,54 which is within the linear range. The thickness of the adsorbed n-alkanes which remains on the silica plate after draining (i.e., at the disjoining pressure of 3 × 10−5 MPa) for higher alkanes (octane onward) ranges from 10 to 40 Å.55 In this study, the pressure of compressed air used for drying of substrate is 0.5 MPa, i.e., before placing it inside the IFT cell for contact angle measurements. Further, reported values of standard adsorption free energy ΔG°ads of alkanes on silica surface show that ΔG°ads decreases with an increase in alkane chain length in the range from −10 to −25 kJ/mol for hexane to nonane, Figure 4.56,57 The above discussion explains the wettability condition of quartz substrate ahead of the wettability alteration of its surface by the dispensed nanofluids.

LSS2 and LSS3, divalent cations are present at lower concentration, and thus, adsorption of surfactant or SO42− on the ZNP surface is higher due to its availability, which gives an effective net negative charge to the nanoaggregates. An increase in the concentration of such negatively charged nanoaggregates increases IFT. LSS4 has no added divalent cations in it but the same amount of surfactant (500 mg/L) and SO42− as the other solutions. Similarly for LSS4 too, an increase in IFT for ZNP concentrations up to 2000 mg/L features a dominating effect of net effective charge which is due to the availability of surfactants for adsorption on the NP surface. 3.2. Effect of Divalent Cation−Sulfate Ion Ratio on IFT of Low-Salinity Surfactant Nanofluids. Figure 3

Figure 3. Experimental values for LSS nanofluid/scCO2 IFT against the divalent cation/sulfate ion ratio (M2+/SO42−): (red square) 0 mg/ L ZNP, (yellow square) 100 mg/L ZNP, (green square) 1000 mg/L ZNP, and (blue square) 2000 mg/L ZNP.

presents the experimental IFT data for low-salinity surfactant nanofluids as a function of divalent cation−sulfate ion ratio (M2+/SO42−). For 1000 mg/L ZNP concentration, IFT decreases and then increases with an increase in M2+/SO42−, whereas this trend reverses for 2000 mg/L ZNP concentration. The highest and lowest IFT values are both experienced at 4.427 M2+/SO42−. This phenomenon can be attributed to the effect of counterion binding by divalent cations to partially deplete SDBS molecules at the interface, causing high IFT at 0/100 mg/L of ZNPs.2 Whereas more divalent cations are available for binding to the headgroup of SDBS or SO42− and prevent them from adsorbing to the weakly positively charged ZNP surface, a high concentration (2000 mg/L) of ZNP decreases the IFT as more of them adsorb at the fluid−fluid interface. For 0/100 mg/L ZNP concentration, IFT values are constant and then increase with an increase in M2+/SO42−. The headgroup charge screening can reduce the electrostatic repulsion between surfactant molecules, and they tend to remain in bulk phase or can even facilitate the micelles formation.63 For 100 mg/L ZNP concentration, the net effective charge of nanoaggregates due to surfactant adsorption can contribute to the IFT increase. Besides, the surfactant concentration is still higher (500 mg/L), its role can be dominating, and the overall IFT behavior can be similar to the 0 ZNP case.

Figure 4. Variation of standard free energy of adsorption ΔG°ads of nalkanes on silica surface (red circle58) and the ratio of density of the nalkanes at the n-alkane/silica interface to bulk density (ρ/ρb) (blue circle59) with their number of carbon atoms.

Figure 5 indicates the low-salinity surfactant nanofluids contact angles as a function of ZNP concentration. Clearly, both advancing (θa, at the leading edge) and receding (θr, at trailing edge) contact angles38,57 of the droplet first decrease and then increase with increasing ZNP concentration. Least θa (44.48°) was observed for LSS1 (at 1000 mg/L ZNP), although the θa (45.85°) of LSS2 (at 100 mg/L ZNP) was also close to the lowest value. Similarly, θr were least for LSS1 and LSS2, whereas θa and θr both are highest for LSS4. This shows that the quartz surface can be turned more water wet when surfactant-augmented ZNP is used in the range of 100−1000 mg/L. Further increasing ZNP concentration further reduces the water wettability. These results have been compared with the 7065

DOI: 10.1021/acs.energyfuels.9b01102 Energy Fuels 2019, 33, 7062−7068

Article

Energy & Fuels

Nanofluids. Figure 7 shows the contact angles of low-salinity surfactant nanofluids as a function of divalent cation−sulfate

Figure 5. Experimental values for LSS nanofluid/quartz contact angles [advancing (θa) and receding (θr)] against the ZNP concentration: (red square) LSS1 θa, (yellow square) LSS2 θa, (green square) LSS3 θa, (blue square) LSS4 θa, (red circle) LSS1 θr, (yellow circle) LSS2 θr, (green circle) LSS3 θr, and (blue circle) LSS4 θr.

Figure 7. Experimental values for LSS nanofluid/quartz contact angle [advancing (θa) and receding (θr)] against the divalent cation/sulfate ion ratio (M2+/SO42−): (red square) 0 mg/L ZNP θa, (yellow square) 100 mg/L ZNP θa, (green square) 1000 mg/L ZNP θa, (blue square) 2000 mg/L ZNP θa, (red circle) 0 mg/L ZNP θr, (yellow circle) 100 mg/L ZNP θr, (green circle) 1000 mg/L ZNP θr, and (blue circle) 2000 mg/L ZNP θr.

contact angle measurements from the study conducted by Giraldo et al.60 and dispensed the water droplet on an alumina nanoparticle (particle size of 35 ± 4 nm, 0−10 000 mg/L, dispersed in an anionic surfactant) treated oil-wet sandstone at room temperature and pressure. Also, Tola et al. dispensed aqueous solution droplets containing zinc oxide nanoparticles (particle size of 25 nm, 0−5000 mg/L) dispersed in 2500 mg/ L SDS surfactant on crude oil-saturated Berea sandstone plates to measure contact angles at ambient conditions.61 This shows that the wettability alteration of quartz is due to the adsorption of ZNP nanoaggregates at low salinity. Furthermore, at low salinity formation of nanoaggregates may occur due to the availability of more surfactant molecules in the aqueous phase; thus, coadsorption of the formed nanoaggregates on the quartz surface takes place altering the wettability toward more water− wet condition, Figure 6. On the contrary, increasing ZNP concentration causes repulsion between the initially coadsorbed (with surfactants adsorbed directly to the quartz surface due to cation bridging) and additionally formed ZNP− surfactant nanoaggregate complexes preventing them from further coadsorption at the quartz surface. 3.4. Effect of the Divalent Cation−Sulfate Ion Ratio on the Contact Angle of Low-Salinity Surfactant

ion ratio (M2+/SO42−). θa and θr both decrease and then increase for 0 and 100 mg/L ZNP concentrations with increasing M2+/SO42−, whereas interestingly, this trend reverses for 1000 and 2000 mg/L nanoparticle concentrations. θa and θr both are highest for 0 M2+/SO42− (at 0 mg/L ZNP) and lowest for 2.575 M2+/SO42− (at 100 mg/L ZNP). On the other hand, θa and θr both are also low for 1000 mg/L ZNP concentration at 4.427 M2+/SO42−. This shows that the optimum range of ZNP concentration and divalent cation− sulfate ion ratio are 100−1000 mg/L and 2.575−4.427, respectively, to render the surface more water wet. In addition, surfactant-augmented ZNPs nanoaggregates coadsorption facilitated by the divalent cation bridging at an optimal condition is responsible for the change of the quartz surface, which becomes more water−wet at low salinity.

4. CONCLUSIONS The effect of the ratio of divalent cations to sulfate ions on the advancing and receding contact angles of drops of low-salinity

Figure 6. Schematic of nanoaggregate coadsorption on the quartz surface. 7066

DOI: 10.1021/acs.energyfuels.9b01102 Energy Fuels 2019, 33, 7062−7068

Article

Energy & Fuels

Alteration of Sandstone: Role of SiO2 Nanoparticles Concentration and Divalent Cation to SO42‑ Ratio. Energy Fuels 2019, 33, 739−746. (4) Pouryousefy, E.; Xie, Q.; Saeedi, A. Effect of Multi-component Ions Exchange on Low Salinity EOR: Coupled Geochemical Simulation Study. Petroleum. 2016, 2, 215−224. (5) Roshan, H.; Al-Yaseri, A. Z.; Sarmadivaleh, M.; Iglauer, S. On wettability of Shale Rocks. J. Colloid Interface Sci. 2016, 475, 104−111. (6) Zhang, L.; Zhang, J.; Wang, Y.; Yang, R.; Zhang, Y.; Gu, J.; Zhang, M.; Ren, S. Experimental Investigation of Low-Salinity Water Flooding in a Low-Permeability Oil Reservoir. Energy Fuels 2018, 32, 3108−3118. (7) Hendraningrat, L.; Li, S.; Torsæter, O. A Coreflood Investigation of Nanofluid Enhanced Oil Recovery. J. Pet. Sci. Eng. 2013, 111, 128− 138. (8) Hosseinzade Khanamiri, H.; Baltzersen Enge, I.; Nourani, M.; Stensen, J.Å.; Torsæter, O.; Hadia, N. EOR by Low Salinity Water and Surfactant at Low Concentration: Impact of Injection and in Situ Brine Composition. Energy Fuels 2016, 30, 2705−2713. (9) Kuang, W.; Saraji, S.; Piri, M. A Systematic Experimental Investigation on the Synergistic Effects of Aqueous Nanofluids on Interfacial Properties and Their Implications for Enhanced Oil Recovery. Fuel 2018, 220, 849−870. (10) Mohajeri, M.; Hemmati, M.; Shekarabi, A. S. An Experimental Study on Using a Nanosurfactant in an EOR Process of Heavy oil in a Fractured Micromodel. J. Pet. Sci. Eng. 2015, 126, 162−173. (11) Wu, Y.; Chen, W.; Dai, C.; Huang, Y.; Li, H.; Zhao, M.; He, L.; Jiao, B. Reducing Surfactant Adsorption on Rock by Silica Nanoparticles for Enhanced Oil Recovery. J. Pet. Sci. Eng. 2017, 153, 283−287. (12) Al-Bayati, D.; Saeedi, A.; Xie, Q.; Myers, M. B.; White, C. Influence of Permeability Heterogeneity on Miscible CO2 Flooding Efficiency in Sandstone Reservoirs: An Experimental Investigation. Transp. Porous Media 2018, 125, 341−356. (13) Jha, N. K.; Ojha, U.; Kumar, A.; Mathur, A. Analysis of CO2 Swelling and Modeling of PVT Properties of Reservoir Fluid of an Onland Field of Gujarat, India. Carbon Manag. Technol. Conf. 2015, 1−10. (14) Karimaie, H.; Lindeberg, E. Experimental Verification of CO2 Dissolution Rate Due to Diffusion Induced Convection. Energy Procedia 2017, 114, 4917−4925. (15) Namani, M.; Souraki, Y.; Kleppe, J.; Høier, L.; Karimaie, H. Scaled Experimental and Simulation Study of Segregation in WaterAbove-Gas Injection. SPE Reserv. Eval. Eng. 2017, 20, 0809−0819. (16) Al-Anssari, S.; Barifcani, A.; Keshavarz, A.; Iglauer, S. Impact of Nanoparticles on the CO2-Brine Interfacial Tension at High Pressure and Temperature. J. Colloid Interface Sci. 2018, 532, 136−142. (17) Al-Khdheeawi, E. A.; Vialle, S.; Barifcani, A.; Sarmadivaleh, M.; Zhang, Y.; Iglauer, S. Impact of Salinity on CO2 Containment Security in Highly Heterogeneous Reservoirs. Greenhouse Gases: Sci. Technol. 2018, 8, 93−105. (18) Iglauer, S. Optimum Storage Depths for Structural CO2 Trapping. Int. J. Greenhouse Gas Control 2018, 77, 82−87. (19) Jha, N. K.; Ali, M.; Sarmadivaleh, M.; Iglauer, S.; Barifcani, A.; Lebedev, M.; Sangwai, J. Low Salinity Surfactant Nanofluids for Enhanced CO2 Storage Application at High Pressure and Temperature. EAGE Fifth CO2 Geological Storage Workshop, Utrecht, Netherlands; EAGE Publications BV, 2018. (20) Al-Bayati, D.; Saeedi, A.; Myers, M.; White, C.; Xie, Q.; Clennell, B. Insight Investigation of Miscible scCO2 Water Alternating Gas (WAG) Injection Performance in Heterogeneous Sandstone Reservoirs. J. CO2 Util. 2018, 28, 255−263. (21) Al-Khdheeawi, E. A.; Vialle, S.; Barifcani, A.; Sarmadivaleh, M.; Iglauer, S. Enhancement of CO2Trapping Efficiency in Heterogeneous Reservoirs by Water-Alternating gas Injection. Greenhouse Gases: Sci. Technol. 2018, 8, 920−931. (22) Hosseinzade Khanamiri, H.; Nourani, M.; Tichelkamp, T.; Stensen, J.Å.; Øye, G.; Torsæter, O. Low-Salinity-Surfactant Enhanced Oil Recovery (EOR) with a New Surfactant Blend: Effect of Calcium Cations. Energy Fuels 2016, 30, 984−991.

surfactant nanofluids on weakly water wet quartz surface at a pressure of 20 MPa and temperature of 70 °C was investigated in this study. The interfacial tension of low-salinity surfactant nanofluids was also measured at the same temperature and pressure conditions. It was clearly observed that the divalent cation to sulfate ion ratio has a prominent role in wettability alteration of weak water−wet quartz surfaces and on the CO2− water interfacial tension of the system when used in combination with SDBS surfactant-augmented ZNPs at low salinity. Maximum change in the advancing and receding angle of a droplet of low-salinity surfactant nanofluids was observed at M2+/SO42− values of 4.427 and 2.575, respectively. It was found that the wettability alteration is more pronounced when ZNP concentration ranges from 100 to 1000 mg/L for M2+/ SO42− values in the range of 2.575−4.427. It is also interesting to observe that the interfacial tension of low-salinity surfactant solutions (LSS2, LSS3, and LSS4) converges at a ZNP concentration of 100 mg/L, below which the change in IFT is independent of the M2+/SO42− ratio. However, the minimum interfacial tension value of 4.7 mN/m is obtained for a M2+/ SO 4 2− value of 4.427 (LSS1) for 2000 mg/L ZNP concentration. Importantly, it was observed that the ratio of divalent cations to sulfate ions plays a vital role in wettability alteration and interfacial tension change irrespective of the divalent to monovalent cations’ ratio or presence of nanoparticles when sulfate ions are present in solution. The synergism and interplay among factors such as coadsorption of surfactant-augmented nanoaggregates and surfactant molecules on the ZNP surface, availability of cations for bridging between surfactant molecules and ZNP surface, availability of SO42− for cations, or adsorption on positively charged nanoparticles surface could contribute to contact angle values/trends. This study has major implications in low-salinity surfactant nanofluids EOR, whereas results could also be used for assessment of their potential use in CO2 geosequestration/ EOR/WAG.



AUTHOR INFORMATION

Corresponding Author

*E-mail: [email protected]. Phone: +91-44 22574825. Fax: +91-44-2257-4802. ORCID

Muhammad Ali: 0000-0002-2446-3072 Jitendra S. Sangwai: 0000-0001-8931-0483 Notes

The authors declare no competing financial interest.



ACKNOWLEDGMENTS We want to acknowledge our technical officers Mr. Jason Wright, Mr. Bob Webb, and Ms. Roshanak Doroushi for their help and management during the contact angle measurements.



REFERENCES

(1) Al-Shalabi, E. W.; Sepehrnoori, K. A Comprehensive Review of Low Salinity/Engineered Water Injections and Their Applications in Sandstone and Carbonate Rocks. J. Pet. Sci. Eng. 2016, 139, 137−161. (2) Jha, N. K.; Iglauer, S.; Sangwai, J. S. Effect of Monovalent and Divalent Salts on the Interfacial Tension of n -Heptane against Aqueous Anionic Surfactant Solutions. J. Chem. Eng. Data 2018, 63, 2341−2350. (3) Jha, N. K.; Iglauer, S.; Barifcani, A.; Sarmadivaleh, M.; Sangwai, J. S. Low Salinity Surfactant Nanofluid Formulations for Wettability 7067

DOI: 10.1021/acs.energyfuels.9b01102 Energy Fuels 2019, 33, 7062−7068

Article

Energy & Fuels

(42) Ali, M.; Al-Anssari, S.; Arif, M.; Barifcani, A.; Sarmadivaleh, M.; Stalker, L.; Lebedev, M.; Iglauer, S. Organic Acid Concentration Thresholds for Ageing of Carbonate Minerals: Implications for CO2Trapping/Storage. J. Colloid Interface Sci. 2019, 534, 88−94. (43) Arif, M.; Barifcani, A.; Lebedev, M.; Iglauer, S. Structural Trapping Capacity of Oil-wet Caprock as a Function of Pressure, Temperature and Salinity. Int. J. Greenhouse Gas Control 2016, 50, 112−120. (44) Arif, M.; Lebedev, M.; Barifcani, A.; Iglauer, S. CO2 Storage in Carbonates: Wettability of Calcite. Int. J. Greenhouse Gas Control 2017, 62, 113−121. (45) Siddiqui, M. A. Q.; Ali, S.; Fei, H.; Roshan, H. Current Understanding of Shale Wettability: A Review on Contact Angle Measurements. Earth-Sci. Rev. 2018, 181, 1−11. (46) Wamkam, C. T.; Opoku, M. K.; Hong, H.; Smith, P. Effects of pH on Heat Transfer Nanofluids Containing ZrO2 and TiO2 Nanoparticles. J. Appl. Phys. 2011, 109, 024305. (47) Chen, Y.; Sari, A.; Xie, Q.; Saeedi, A. Excess H+ Increases Hydrophilicity During CO2-Assisted Enhanced Oil Recovery in Sandstone Reservoirs. Energy Fuels 2019, 33, 814−821. (48) Allen, F. J.; Griffin, L. R.; Alloway, R. M.; Gutfreund, P.; Lee, S. Y.; Truscott, C. L.; Welbourn, R. J. L.; Wood, M. H.; Clarke, S. M. An Anionic Surfactant on an Anionic Substrate: Monovalent Cation Binding. Langmuir 2017, 33, 7881−7888. (49) Dugyala, V. R.; Muthukuru, J. S.; Mani, E.; Basavaraj, M. G. Role of Electrostatic Interactions in the Adsorption Kinetics of Nanoparticles at Fluid-Fluid Interfaces. Phys. Chem. Chem. Phys. 2016, 18, 5499−5508. (50) Ward, A. F. H.; Tordai, L. Time-Dependence of Boundary Tensions of Solutions I. The Role of Diffusion in Time-Effects. J. Chem. Phys. 1946, 14, 453−461. (51) Brindza, M. R.; Ding, F.; Fourkas, J. T.; Walker, R. A. N-Alkane Adsorption to Polar Silica Surfaces. J. Chem. Phys. 2010, 132, 114701. (52) Schlangen, L. J. M.; Koopal, L. K. Self-Consistent Field Theory for the Adsorption of Alkanes on Solid Surfaces. Langmuir 1996, 12, 1863−1869. (53) Schlangen, L. J. M.; Koopal, L. K.; Stuart, M. A. C.; Lyklema, J.; Robin, M.; Toulhoat, H. Thin Hydrocarbon and Water Films on Bare and Methylated Silica: Vapor Adsorption, Wettability, Adhesion, and Surface Forces. Langmuir 1995, 11, 1701−1710. (54) NIST Chemistry WebBook, SRD 69. (55) Gee, M. L.; Healy, T. W.; White, L. R. . Ellipsometric Studies of Alkane Adsorption on Quartz. J. Colloid Interface Sci. 1989, 131, 18− 23. (56) Liu, Y.; Chase, H. M.; Geiger, F. M. Partially (resp. fully) Reversible Adsorption of Monoterpenes (resp. alkanes and cycloalkanes) to Fused Silica. J. Chem. Phys. 2019, 150, 074701. (57) Nwidee, L. N.; Lebedev, M.; Barifcani, A.; Sarmadivaleh, M.; Iglauer, S. Wettability Alteration of Oil-wet Limestone Using Surfactant-Nanoparticle Formulation. J. Colloid Interface Sci. 2017, 504, 334−345. (58) Papirer, E. Adsorption on Silica Surfaces; CRC Press, 2018. (59) De Almeida, J. M.; Miranda, C. R. Improved Oil Recovery in Nanopores: NanoIOR. Sci. Rep. 2016, 6, 28128. (60) Giraldo, J.; Benjumea, P.; Lopera, S.; Cortes, F. B.; Ruiz, M. A. . Wettability Alteration of Sandstone Cores by Alumina-Based Nanofluids. Energy Fuels 2013, 27, 3659−3665. (61) Tola, S.; Sasaki, K.; Sugai, Y. Wettability Alteration of Sandstone With Zinc Oxide Nano-Particles. 23rd Formation Evaluation Symposium of Japan 2017, Chiba, Japan; 2017; pp 1−4. (62) Arif, M.; Abu-Khamsin, S. A.; Iglauer, S. Wettability of Rock/ CO2/Brine and Rock/oil/CO2-enriched-brine Systems: Critical Parametric Analysis and Future Outlook. Adv. Colloid Interface Sci. 2019, 268, 91−113. (63) Dreiss, C. A. Wormlike Micelles: Where do we Stand? Recent Developments, Linear Rheology and Scattering Techniques. Soft Matter 2007, 3, 956−970.

(23) Hosseinzade Khanamiri, H.; Torsaeter, O.; Stensen, J. A. Effect of Calcium in Pore Scale Oil Trapping by Low-Salinity Water and Surfactant Enhanced Oil Recovery at Strongly Water-Wet Conditions: In Situ Imaging by X-ray Microtomography. Energy Fuels 2016, 30, 8114−8124. (24) Jackson, M. D.; Al-Mahrouqi, D.; Vinogradov, J. Zeta Potential in Oil-Water-Carbonate Systems and its Impact on Oil Recovery During Controlled Salinity Water-Flooding. Sci. Rep. 2016, 6, 37363. (25) Kakati, A.; Sangwai, J. S. Wettability Alteration of Mineral Surface during Low-Salinity Water Flooding: Role of Salt Type, Pure Alkanes, and Model Oils Containing Polar Components. Energy Fuels 2018, 32, 3127−3137. (26) Kakati, A.; Sangwai, J. S. Effect of Monovalent and Divalent Salts on the Interfacial Tension of Pure Hydrocarbon-Brine Systems Relevant for Low Salinity Water Flooding. J. Pet. Sci. Eng. 2017, 157, 1106−1114. (27) Wei, B.; Wu, R.; Lu, L.; Ning, X.; Xu, X.; Wood, C.; Yang, Y. Influence of Individual Ions on Oil/Brine/Rock Interfacial Interactions and Oil-Water Flow Behaviors in Porous Media. Energy Fuels 2017, 31, 12035−12045. (28) Kobayashi, K.; Liang, Y.; Murata, S.; Matsuoka, T.; Takahashi, S.; Amano, K. I.; Nishi, N.; Sakka, T. Stability Evaluation of Cation Bridging on Muscovite Surface for Improved Description of IonSpecific Wettability Alteration. J. Phys. Chem. C 2017, 121, 9273− 9281. (29) Fauziah, C. A.; Al-Yaseri, A. Z.; Beloborodov, R.; Siddiqui, M. A. Q.; Lebedev, M.; Parsons, D.; Roshan, H.; Barifcani, A.; Iglauer, S. Carbon Dioxide/Brine, Nitrogen/Brine, and Oil/Brine Wettability of Montmorillonite, Illite, and Kaolinite at Elevated Pressure and Temperature. Energy Fuels 2019, 33, 441−448. (30) Iglauer, S. CO2-Water-Rock Wettability: Variability, Influencing Factors, and Implications for CO2 Geostorage. Acc. Chem. Res. 2017, 50, 1134−1142. (31) Iglauer, S.; Pentland, C. H.; Busch, A. CO2Wettability of Seal and Reservoir Rocks and the Implications for Carbon GeoSequestration. Water Resour. Res. 2015, 51, 729−774. (32) Xie, Q.; Saeedi, A.; Pooryousefy, E.; Liu, Y. Extended DLVObased Estimates of Surface Force in Low Salinity Water Flooding. J. Mol. Liq. 2016, 221, 658−665. (33) Nasralla, R. A.; Nasr-El-Din, H. A. Impact of Electrical Surface Charges and Cation Exchange on Oil Recovery by Low Salinity Water. SPE Asia Pacific Oil Gas Conference Exhibition; SPE, 2011. (34) Iglauer, S.; Favretto, S.; Spinelli, G.; Schena, G.; Blunt, M. J. Xray Tomography Measurements of Power-Law Cluster Size Distributions for the Nonwetting Phase in Sandstones. Phys. Rev. E 2010, 82, 056315. (35) Iglauer, S.; Wülling, W. The Scaling Exponent of Residual Nonwetting Phase Cluster Size Distributions in Porous Media. Geophys. Res. Lett. 2016, 43, 11253−11260. (36) Suzzoni, A.; Barre, L.; Kohler, E.; Levitz, P.; Michot, L. J.; M’Hamdi, J. Interactions Between Kaolinite Clay and AOT. Colloids Surf., A 2018, 556, 309−315. (37) Wu, Y.; Iglauer, S.; Shuler, P.; Tang, Y.; Goddard, W. A. Experimental Study of Surfactant Retention on Kaolinite Clay. Tenside, Surfactants, Deterg. 2011, 48, 346−358. (38) Nwidee, L. N.; Al-Anssari, S.; Barifcani, A.; Sarmadivaleh, M.; Lebedev, M.; Iglauer, S. Nanoparticles Influence on Wetting Behaviour of Fractured Limestone Formation. J. Pet. Sci. Eng. 2017, 149, 782−788. (39) Al-Anssari, S.; Wang, S.; Barifcani, A.; Iglauer, S. Oil-Water Interfacial Tensions of Silica Nanoparticle-Surfactant Formulations. Tenside, Surfactants, Deterg. 2017, 54, 334−341. (40) Roustaei, A.; Bagherzadeh, H. Experimental Investigation of SiO2 Nanoparticles on Enhanced Oil Recovery of Carbonate Rservoirs. J. Pet. Explor. Prod. Technol. 2015, 5, 27−33. (41) Holzwarth, A.; Leporatti, S.; Riegler, H. Molecular Ordering and Domain Morphology of Molecularly Thin Triacontane Films at SiO2/air Interfaces. Europhys. Lett. 2000, 52, 653−659. 7068

DOI: 10.1021/acs.energyfuels.9b01102 Energy Fuels 2019, 33, 7062−7068