A Quantitative Model for the Coupled Kinetics of Arsenic Adsorption

A large volume of studies has been done on the mechanisms of As(III) reactions with. 51. MnO2 minerals.7-11,13-15 .... (data not shown), to simplify t...
0 downloads 6 Views 1MB Size
Subscriber access provided by UNIV OF DURHAM

Letter

A Quantitative Model for the Coupled Kinetics of Arsenic Adsorption/Desorption and Oxidation on Manganese Oxides Xionghan Feng, Pei Wang, Zhenqing Shi, Kideok D. Kwon, Huaiyan Zhao, Hui Yin, Zhang Lin, Mengqiang Zhu, Xinran Liang, Fan Liu, and Donald L. Sparks Environ. Sci. Technol. Lett., Just Accepted Manuscript • DOI: 10.1021/acs.estlett.8b00058 • Publication Date (Web): 28 Feb 2018 Downloaded from http://pubs.acs.org on March 1, 2018

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Environmental Science & Technology Letters is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 16

Environmental Science & Technology Letters

1

A Quantitative Model for the Coupled Kinetics of Arsenic

2

Adsorption/Desorption and Oxidation on Manganese Oxides Xionghan Feng,† Pei Wang,‡ Zhenqing Shi,‡,* Kideok D. Kwon,§ Huaiyan Zhao,† Hui Yin,† Zhang Lin,‡ Mengqiang Zhu, Xinran Liang,† Fan Liu,† Donald L. Sparks⊥

3 4

ǁ

5 6 7 8



Key Laboratory of Arable Land Conservation (Middle and Lower Reaches of Yangtze River), Ministry of Agriculture, College of Resources and Environment, Huazhong Agricultural University, Wuhan 430070, People’s Republic of China ‡

9 10

School of Environment and Energy, South China University of Technology, Guangzhou, Guangdong 510006, People’s Republic of China

11 12

§

13 14 15 16

Department of Geology, Kangwon National University, Chuncheon 24347, Republic of Korea

ǁ

Department of Ecosystem Science and Management, University of Wyoming, Laramie, WY, 82071, United States ⊥

Environmental Soil Chemistry Group, Delaware Environmental Institute and Department of Plant and Soil Sciences, University of Delaware, Newark, Delaware, 19716, United States

17 18 19

*Corresponding author:

20

Zhenqing Shi; Tel: +86 20 39380503; e-mail: [email protected].

21 22

23

1

ACS Paragon Plus Environment

Environmental Science & Technology Letters

24

Abstract

25

The ability to predict coupled kinetic reactions of arsenic (As) that occur at the

26

manganese oxide-aqueous solution interface is crucial for management and remediation of As

27

contaminated sites worldwide. A quantitative understanding of the coupling between As

28

oxidation and adsorption/desorption kinetics will enable us to more accurately predict the

29

kinetic behavior of As. In this study, we developed a novel quantitative model for the coupled

30

kinetics of As adsorption/desorption/oxidation on δ-MnO2. The kinetics of As(III) adsorption

31

and oxidation on δ-MnO2 was studied using a stirred-flow method under varying influent

32

As(III) concentrations. The model was able to account for the variations of As

33

concentrations, different binding behavior of As(III) and As(V), and flow rates. Our model

34

quantitatively shows that the coupled As adsorption/desorption/oxidation processes are

35

highly dependent on As mass loading rates on δ-MnO2. Our model suggests that the As(III)

36

adsorption rate is much higher than its oxidation rate. Both As(III) oxidation and subsequent

37

As(V) desorption may proceed with similar reaction rates and control the overall reaction

38

rates, although As(V) desorption rates may be affected by As(V) re-adsorption. Our kinetics

39

model contributes to prediction of the dynamic behavior of As when manganese oxides are

40

present.

41

Introduction

42

Arsenic (As) is a redox sensitive contaminant affecting human health and its

43

speciation and fate are greatly affected by soil minerals.1,2 Among various minerals,

44

manganese (Mn) oxides are of much of interest,3,4 and the poorly crystalline phyllomangantes

45

such as δ-MnO2 exhibit the highest reactivity with As.5,6 As(III) is readily oxidized to As(V)

46

when reacted with δ-MnO2, which is coupled by the As(III)/As(V) adsorption/desorption

47

reactions, and the overall As reactions with δ-MnO2 may not reach an equilibrium

48

instantaneously.7-12 A quantitative understanding on the coupled kinetic reactions of As that

49

occur at the Mn oxide-water interface is essential in predicting the fate and transport of As in

50

soil.

51

A large volume of studies has been done on the mechanisms of As(III) reactions with

52

MnO2 minerals.7-11,13-15 Adsorption of As(III) and subsequent oxidation to As(V) usually 2

ACS Paragon Plus Environment

Page 2 of 16

Page 3 of 16

Environmental Science & Technology Letters

53

occurs at the edge sites of MnO2.10-12,15 Quick-scanning x-ray absorption spectroscopy

54

determined the initial oxidation rate constants of As(III) by MnO2 at sub-second time-

55

scales.16 At a longer reaction time, Mn(II, III) produced during the coupled As(III)

56

adsorption/oxidation reactions may significantly affect the As reaction kinetics by passivating

57

the surface sites.7-9,11,15,17,18 Although the apparent kinetics of As(III) were extensively

58

modelled using kinetic rate equations,13,16,17,19 previous modeling work rarely simultaneously

59

considered both As oxidation and nonlinear As adsorption/desorption kinetics, which may

60

prevent accurate prediction of the reaction rates when As(III) adsorbs onto Mn oxides. How

61

each individual reaction of the coupled As adsorption/desorption and oxidation processes

62

contributes to the overall reaction rate is still largely unknown. Thus, it is desired to develop a

63

theoretical basis to quantify the coupled As kinetic reactions at the MnO2-solution interface.

64

In this study, we examined the initial stages of the coupled kinetics of As

65

adsorption/desorption and oxidation on δ-MnO2 in which the role of Mn(II, III) is presumed

66

to be relatively small.7,8 We developed a novel mechanistic-based quantitative model for the

67

kinetics of the coupled reactions of As(III) adsorption/desorption, As(III) oxidation and

68

subsequent As(V) adsorption/desorption at the MnO2-solution interface. We expect that the

69

kinetics model would significantly advance our quantitative understanding and prediction of

70

the dynamic behavior of As species in the environment.

71

Materials and Methods

72

1. Synthesis and characterization of δ-MnO2. δ-MnO2 was synthesized via the

73

redox reaction between MnCl2 and NaMnO4 in an alkaline medium.20 The obtained powder

74

was washed with DI water and freeze-dried. Ground samples (< 250 µm) were analyzed with

75

powder XRD for mineral composition, the BET method for specific surface area, field

76

emission scanning electron microscopy (FESEM) and transition electron microscopy (TEM)

77

for morphology, and for Mn average oxidation state (AOS).21

78

2. Arsenic Adsorption/Desorption and Oxidation Kinetic Experiments. The

79

kinetic experiments were conducted using a stirred-flow reactor.14,22 Briefly, a δ-MnO2

80

suspension (1, 2, and 10 g L-1) and a Teflon-coated magnetic stir bar were placed into the

81

reaction cell (volume = 8.5 cm3 or 7.5 cm3). A 0.45-µm pore size membrane filter was used

82

to retain the mineral particles in the reaction cell. The background electrolytes were NaNO3 3

ACS Paragon Plus Environment

Environmental Science & Technology Letters

Page 4 of 16

83

buffered at pH 7.0 using MOPS. Two sets of experiments were conducted, one with low

84

influent As(III) concentrations (0.67 – 5.71 µM) and the other with high influent As(III)

85

concentrations (500 – 1500 µM). To initiate the kinetic experiment, the As(III) solution was

86

pumped through the reactor and the effluent was collected at fixed time intervals. The δ-

87

MnO2 suspension was well mixed by the stir bar during the kinetic experiments. The

88

experiment continued for 30 min. The flow rate for most experiments was 2 mL min-1 while

89

different flow rates (1 and 3 mL min-1) were also tested for selected experiments. Additional

90

experiments were also conducted to study As(V) adsorption and desorption kinetics. Details

91

of all stirred-flow kinetic experiments are described in the S1 section of Supporting

92

Information (SI).

93

3. Arsenic(V) Adsorption Isotherm Experiments. The adsorption isotherm of

94

As(V) by δ-MnO2 was studied in a batch reactor with a δ-MnO2 suspension concentration of

95

10 g L-1, which is described in SI (S2 section).

96

For all solution samples, total As and Mn concentrations were analyzed using

97

inductively coupled plasma mass spectrometry. For the experiments with high As

98

concentrations, the concentrations of As(V) were measured using the molybdenum blue

99

method, while for the experiments with low As concentrations, As(III) and As(V)

100

concentrations were analyzed by high performance liquid chromatography and atomic

101

fluorescence spectrometry.

102

Modeling Methods

103 104

1. Kinetic Model Development. Here we propose a conceptual model for the coupled As kinetic reactions at the MnO2-solution interface as follows,

105

(1)

106

The model contains three key reactions: (i) As(III) in solution (Cw,As(III)) is in instantaneous

107

equilibrium with the adsorbed As(III) on MnO2 surface sites (Cp,As(III)), with a partition

108

coefficient Kp,As(III), (ii) adsorbed As(III) is oxidized to As(V) on MnO2 surface sites

109

(Cp,As(V)), with an oxidation rate constant k (min-1), and (iii) the adsorbed As(V) on the MnO2 4

ACS Paragon Plus Environment

Page 5 of 16

Environmental Science & Technology Letters

110

surface sites is released into the solution (Cw,As(V)), with adsorption and desorption rate

111

coefficients ka,As(V) (min-1) and kd,As(V) (min-1), respectively.

112

To account for the effect of passivation of MnO2 during reactions, the oxidation rate

113

constant k may change with time. We propose a general approach to describe it,

114

k = k0*P(t)

115

in which k0 (min-1) is the initial As(III) oxidation rate constant and P(t) is a function reflecting

116

the passivation effect on k as reactions proceed, which may be due to Mn(II)/Mn(III) and

117

As(V) adsorption on MnO2 surface sites. Since the effluent Mn2+ concentrations are very low

118

(data not shown), to simplify the model for the initial stages of the kinetic reactions, we used

119

an exponential function to describe P(t),

120

P(t) = exp[-b(As(III)supl./MnO2)]

121

in which b is a constant, As(III)supl. is the total accumulated amount of As(III) supplied to the

122

reactor at time t and MnO2 is the total amount of MnO2 in the reactor.

(2)

(3)

123

One central issue is how to specifically incorporate the nonlinear adsorption reactions

124

into the oxidation reactions with time. The adsorption of As(V) on δ-MnO2 shows a typical

125

nonlinear adsorption behavior within a wide range of As(V) concentrations (Figure S1, SI).

126

Specifically coupling nonlinear As(V) binding with As(III) oxidation kinetics will enable us

127

to more accurately assess the contribution of each individual reaction. Shi et al.23,24 have

128

developed kinetic modeling approaches to consider the kinetics of nonlinear adsorption

129

processes. Using a similar modeling concept, the adsorption rate coefficient of As(V) at a

130

given reaction time can be calculated based on the equilibrium partition coefficient (Kp,As(V))

131

and the desorption rate coefficient,

132

ka,As(V) = kd,As(V)K p,As(V)

133

In equation 4, Kp,As(V) is a function of Cp,As(V) that changes with the reaction time, and kd,As(V)

134

is assumed to remain constant irrespective of reaction conditions, which suggests a

135

disjunctive reaction pathway for the desorption reaction.

136

(4)

The following equations are responsible for As(III) and As(V) concentrations in the

137

stirred-flow reactor,

138

Cp,As(III) = Cw,As(III)Kp,As(III)

(5) 5

ACS Paragon Plus Environment

Environmental Science & Technology Letters

139

dCp,As(V) = kCp,As(III) + kaC w,As(V) − kdCp,As(V) = kCp,As(III) + kdK p,As(V)C w,As(V) − kd Cp,As(V) (6) dt

140

dCw,As(V) Q Q = kd Cp,As(V) − ka Cw,As(V) − Cw,As(V) = kdCp,As(V) − kd K p,As(V)C w,As(V) − Cw,As(V) (7) dt V V

141

CT,As = Cw,As(III) + Cw,As(V) + Cp,As(III) + Cp,As(V)

(8)

142

dCT,As Q = (C0 − C w,As(III) − C w,As(V)) dt V

(9)

143

where C0 is the influent As(III) concentration, Q (L min-1) is the flow rate, and V (L) is the

144

reaction volume of the reactor. All concentration terms have a unit of mol L-1, and, as a

145

result, both Kp,As(III) and Kp,As(V) are dimensionless.

146

An implicit finite difference numerical method was used to solve the model equations

147

in Excel. Our model has four global fitting parameters, k0, Kp,As(III), kd,As(V), and b. For each

148

observation time, the square of the difference between measured and model calculated

149

concentrations of both As(III) and As(V) was calculated. All squared errors for each data set

150

were summed to obtain the total squared error. The SOLVER program was used to obtain

151

model parameters by minimizing the total squared error. Details of the kinetics model are

152

presented in SI (S3 section, Figures S2 and S3).

153

Results and Discussion

154

Mineral Characterization. The powder XRD patterns and TEM images of the δ-

155

MnO2 samples are presented in Figure S4 (SI). The 0.242 nm and 0.142 nm reflections for

156

vernadite matched quite well with those reported in the literature.20,25 The δ-MnO2 sample

157

was composed of small particles and the TEM images showed fine small particles that

158

aggregated to large aggregates with low crystallinity. This is consistent with the result of the

159

BET measurement with a relatively large specific surface area of 196.2 m2 g-1. The Mn AOS

160

value of the synthesized δ-MnO2 is 3.84.

161

Modeling As Adsorption/Desorption and Oxidation Kinetics. The changes of

162

effluent As(III) and As(V) concentrations with time under varying influent As(III)

163

concentrations and flow rates are shown in Figure 1 for both low and high influent As(III)

164

concentrations, which results in varying As(III) loadings on MnO2 in the stirred-flow reactor. 6

ACS Paragon Plus Environment

Page 6 of 16

Page 7 of 16

Environmental Science & Technology Letters

165

Both low (Figure 1a and 1b) and high As concentration data (Figure 1c and 1d) showed

166

similar patterns for the effluent As(V) concentrations, which increased with time. No

167

detectable As(III) was observed for the low As concentration data (Figure 1a and 1b) while

168

the effluent As(III) concentrations slowly increased with time under high As loadings (Figure

169

1c and 1d). The model was able to reproduce the effluent data across a wide range of As

170

concentrations, supporting the validity of our modeling approach. The model parameters are

171

summarized in Table S1 (SI). The root mean square errors (RMSE) analysis showed that

172

generally the model fits the experimental data reasonably well, with RMSE values less than 9%

173

of the influent As concentration for all experiments. The kinetics of As(V) adsorption and

174

desorption, determined from the independent experiments, can also be well reproduced using

175

the obtained model parameters (Figures S3 and S5, SI).

176

One of the prominent features in our model is the ability to simultaneously compute

177

the adsorption/desorption rates of both As(III) and As(V) with time during As(III) oxidation

178

process, since it is usually not feasible to determine As(III) adsorption experimentally due to

179

the fast oxidation by MnO2. For most experiments, the amount of As(III) adsorbed was

180

significantly lower than that of As(V) on the MnO2 surface. The lower adsorption of As(III)

181

than As(V) is consistent with a previous prediction using quantum chemical calculations.15

182

At low As(III) loadings in the reactor, the amount of As(III) adsorbed on MnO2 increased

183

with reaction time and then approached a steady value after about a few minutes (Figure 2a

184

and 2b). This suggests that, after a few minutes, the rate of As(III) oxidation approximately

185

equaled the rate of As(III) supply in the reactor that was controlled by the As(III) loading

186

rate. As(V) adsorption on MnO2 continued to increase with time, indicating As(III) oxidation

187

rate was higher than the rate of As(V) desorption from MnO2 surfaces when As(III) loadings

188

in the reactor were low.

189

In comparison, at high As(III) loadings in the reactor, the amount of As(III) adsorbed

190

on MnO2 steadily increased with reaction time while the amount of As(V) adsorbed slowed

191

down after a few reactor volumes (about 20 min) (Figure 2c and 2d). This suggests that the

192

oxidation rate of As(III) became lower than the rate of As(III) supply in the reactor at high

193

As(III) loadings. Therefore, available MnO2 surface sites significantly affected the time-

194

dependent As(III) accumulation on MnO2. The accumulation of As(V) on MnO2 suggests that

195

As(III) oxidation rates were higher than the overall rates of As(V) release from the MnO2 7

ACS Paragon Plus Environment

Environmental Science & Technology Letters

196

surface in the beginning and these two reaction rates were similar with increased As(V)

197

adsorption. Note that the overall As(V) release from MnO2 was controlled by both the rates

198

of As(V) desorption and re-adsorption reactions (equations 1 and 4). The importance of

199

As(V) re-adsorption was evidenced by the desorption experiments with 0.1 M NaOH (pH =

200

13) as the desorbing reagent. At pH 13, the As(V) re-adsorption reaction was minimal due to

201

low As(V) partition coefficients (equation 4) and solution As(V) concentrations spiked

202

quickly (Figure S5, SI).

203

The time dependent changes of As(III) oxidation rates are presented in Figure 3 for

204

both high and low As concentration experiments, in which the previously reported As(III)

205

oxidation rate constant (0.282 min-1) by Ginder-Vogel et al. (2009)16 was also included. For

206

the low As concentration data, k values changed little during the 30-min experiments,

207

consistent with the low As(III) loadings on MnO2 in those experiments. However, for the

208

high As concentration data, k values declined with time and the decline rates of k values were

209

higher at higher As(III) loadings in the reactor. The decline of k values with the increase in

210

As loadings on MnO2 suggests that the production of Mn(II)/Mn(III) may passivate the MnO2

211

surface, which slowed the As(III) oxidation rates as the reaction process proceeded.

212

Furthermore, As(V) adsorption on the MnO2 surface, especially at high As(V) adsorption

213

(Figure 2), may significantly compete with As(III) adsorption sites on MnO2,15 which,

214

indirectly, may slow the overall As(III) oxidation rates.

215

Model Assessment and Implications. Our study provides a quantitative modeling

216

framework for the coupled oxidation and adsorption/desorption kinetics in the initial stages of

217

As(III) adsorption to MnO2, which has significant implications for predicting As cycling in

218

the environment. It provides a quantitative tool to assess how adsorption, desorption, and

219

oxidation reactions affect the overall reaction rates under various As(III) loadings in the

220

reactor. Based on our model calculations, the As(III) adsorption rate is much higher than its

221

oxidation rate. A slow As(III) adsorption rate would otherwise result in a quick buildup of

222

As(III) in the effluent, which was not observed in any of our kinetic experiments. Note that

223

the overall As(III) adsorption rate is controlled by both As(III) adsorption and As(III)

224

desorption (the back reaction) processes. Therefore, fast oxidation of As(III) reduces

225

adsorbed As(III) on MnO2 and minimizes As(III) desorption from MnO2, which promotes the

226

overall As(III) adsorption rate as observed in this study. 8

ACS Paragon Plus Environment

Page 8 of 16

Page 9 of 16

Environmental Science & Technology Letters

227

The As(III) oxidation rate constant, k, and As(V) desorption rate coefficient, kd,As(V),

228

are in the same order of magnitude (Table S1, SI), suggesting that As(III) oxidation and

229

As(V) desorption may proceed with similar reaction rates (equations 6 and 7). As(V)

230

adsorption rate coefficients may vary significantly during the kinetic reactions, due to As(V)

231

partition coefficients quickly decreasing with As(V) adsorption on MnO2 (Figure S2, SI). In

232

most reaction times, our model calculations showed that As(V) adsorption rate coefficients,

233

as determined by equation 4, may be of the same order of magnitude as both k and kd,As(V).

234

Overall, in our stirred-flow experiments, both As(III) oxidation and As(V) desorption

235

together may control the release of As(III) and As(V) from MnO2, which was dependent on

236

the As(III) loadings on MnO2.

237

Our current model applies to the initial stages of the coupled kinetics of As

238

adsorption/desorption and oxidation on δ-MnO2. At longer reaction time, the changes in

239

MnO2 composition, such as accumulation of structural Mn(II, III),26 may be significant, and

240

the time-dependent function of k will need modification based on molecular information of

241

MnO2 composition. Future kinetic studies should also account for the variations in reaction

242

chemistry, such as pH, competing anions (PO43-, CO32-, etc.) and dissolved organic matter,

243

and other competing soil sorbents (e.g. iron oxides), which can be incorporated into the

244

kinetics model using the similar kinetic modeling approach presented in this study and some

245

recent studies.27 Detailed consideration of those factors will enable us to develop a

246

comprehensive model to predict As redox cycling in soils, based on the kinetics model

247

developed in this study.

248

Supporting Information Available

249

Supporting information includes (1) details of stirred-flow kinetic experiments, (2)

250

As(V) adsorption isotherm experiments, (3) details of the kinetics model, (4) XRD and FE-

251

SEM/TEM results, and (5) additional figures. This material is available free of charge at

252

http://pubs.acs.org.

253

Notes

254

The authors declare no competing financial interest. 9

ACS Paragon Plus Environment

Environmental Science & Technology Letters

255

256

Acknowledgments

257

We appreciate the thoughtful comments and constructive suggestion by three

258

anonymous reviewers and Dr. M. Ginder-Vogel to whom we also owe thanks for his sharing

259

additional kinetic data from his group. We gratefully acknowledge the National Natural

260

Science Foundation of China (No. 41471194, 41573090), the Strategic Priority Research

261

Program of the Chinese Academy of Sciences (grant no XDB15020402), Guangdong

262

Innovative and Entrepreneurial Research Team Program (No. 2016ZT06N569), and the

263

Thousand Talent Program for Young Outstanding Scientists of China for financial support of

264

this research. K.K. was supported by the Basic Science Research Program of Korea (NRF-

265

2015R1A4A1041105). M.Z. was supported by the U.S. National Science Foundation

266

(EAR‑1529937).

267

10

ACS Paragon Plus Environment

Page 10 of 16

Page 11 of 16

Environmental Science & Technology Letters

268

References

269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314

(1) Hettick, B. E.; Cañas-Carrell, J. E.; French, A. D.; Klein, D. M. Arsenic: a review of the element’s toxicity, plant interactions, and potential methods of remediation. J. Agric. Food Chem. 2015, 63, 7097-7107. (2) Stuckey, J. W.; Schaefer, M. V.; Benner, S. G.; Fendorf, S. Reactivity and speciation of mineral-associated arsenic in seasonal and permanent wetlands of the Mekong Delta. Geochim. Cosmochim. Acta 2015, 171, 143-155. (3) Post, J. E. Manganese oxide minerals: crystal structures and economic and environmental significance. Proc. Natl. Acad. Sci. USA 1999, 96, 3447-3454. (4) Vodyanitskii, Y. N. Clays & Clay Minerals. Eurasian Soil Sci. 2009, 42, 1170-1178. (5) Feng, X. H.; Zhai, L. M.; Tan, W. F.; Liu, F.; He, J. Z. Adsorption and redox reactions of heavy metals on synthesized Mn oxide minerals. Environ. Pollut. 2007, 147, 366-373. (6) Villalobos, M.; Escobar-Quiroz, I. N.; Salazar-Camacho, C. The influence of particle size and structure on the sorption and oxidation behavior of birnessite: I. Adsorption of As(V) and oxidation of As(III). Geochim. Cosmochim. Acta 2014, 125, 564-581. (7) Lafferty, B. J.; Ginder-Vogel, M.; Zhu, M.; Livi, K. J. T.; Sparks, D. L. Arsenite oxidation by a poorly crystalline manganese-oxide. 2. results from x-ray absorption spectroscopy and x-ray diffraction. Environ. Sci. Technol. 2010, 44, 8467-8472. (8) Lafferty, B. J.; Ginder-Vogel, M.; Sparks, D. L. Arsenite oxidation by a poorly crystalline manganese-oxide 1. stirred-flow experiments. Environ. Sci. Technol. 2010, 44, 8460-8466. (9) Lafferty, B. J.; Ginder-Vogel, M.; Sparks, D. L. Arsenite oxidation by a poorlycrystalline manganese oxide. 3. arsenic and manganese desorption. Environ. Sci. Technol. 2011, 45, 9218-9223. (10) Moore, J. N. Reaction scheme for the oxidation of As(III) to As(V) by birnessite. Clays Clay Miner. 1990, 38, 549-555. (11) Tournassat, C.; Charlet, L.; Bosbach, D.; Manceau, A. Arsenic(III) oxidation by birnessite and precipitation of manganese(II) arsenate. Environ. Sci. Technol. 2002, 36, 493500. (12) Yin, H.; Tan, W.; Zheng, L.; Cui, H.; Qiu, G.; Liu, F.; Feng, X. Characterization of Nirich hexagonal birnessite and its geochemical effects on aqueous Pb2+ /Zn2+ and As(III). Geochim. Cosmochim. Acta 2012, 93, 47–62. (13) Fischel, M. H. H.; Fischel, J. S.; Lafferty, B. J.; Sparks, D. L. The influence of environmental conditions on kinetics of arsenite oxidation by manganese-oxides. Geochemical Transactions 2015, 16, 15. (14) Wu, Y.; Li, W.; Sparks, D. L. Effect of Iron(II) on arsenic sequestration by δ-MnO2: desorption studies using stirred-flow experiments and X-ray absorption fine structure spectroscopy. Environ. Sci. Technol. 2015, 49, 13360-8. (15) Zhu, M.; Paul, K. W.; Kubicki, J. D.; Sparks, D. L. Quantum chemical study of arsenic (III, V) adsorption on Mn-oxides: implications for Arsenic(III) oxidation. Environ. Sci. Technol. 2009, 43, 6655-6661. (16) Ginder-Vogel, M.; Landrot, G.; Fischel, J. S.; Sparks, D. L. Quantification of rapid environmental redox processes with quick-scanning x-ray absorption spectroscopy (Q-XAS). Proc. Natl. Acad. Sci. USA 2009, 106, 16124-16128. (17) Manning, B. A.; Fendorf, S. E.; Bostick, B.; Suarez, D. L. Arsenic(III) oxidation and arsenic(V) adsorption reactions on synthetic birnessite. Environ. Sci. Technol. 2002, 36, 976981. 11

ACS Paragon Plus Environment

Environmental Science & Technology Letters

315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338

(18) Yin, H.; Feng, X.; Qiu, G.; Tan, W.; Liu, F. Characterization of co-doped birnessites and application for removal of lead and arsenite. J. Hazard. Mater. 2011, 188, 341. (19) Scott, M. J.; Morgan, J. J. Reactions at oxide surfaces. 1. oxidation of As(III) by synthetic birnessite. Environ. Sci. Technol. 1995, 29, 1898-1905. (20) Villalobos, M.; Toner, B.; Bargar, J.; Sposito, G. Characterization of the manganese oxide produced by pseudomonas putida strain MnB1. Geochim. Cosmochim. Acta 2003, 67, 2649-2662. (21) Kijima, N.; Yasuda, H.; Sato, T.; Yoshimura, Y. Preparation and characterization of open tunnel oxide α-MnO2 precipitated by ozone oxidation. J. Solid State Chem. 2001, 159, 94-102. (22) Shi, Z.; Di Toro, D. M.; Allen, H. E.; Ponizovsky, A. A. Modeling kinetics of Cu and Zn release from soils. Environ. Sci. Technol. 2005, 39, 4562-8. (23) Shi, Z.; Toro, D. M. D.; Allen, H. E.; Sparks, D. L. A WHAM−based kinetics model for Zn adsorption and desorption to soils. Environ. Sci. Technol. 2008, 42, 5630-6. (24) Shi, Z.; Di Toro, D. M.; Allen, H. E.; Sparks, D. L. A general model for kinetics of heavy metal adsorption and desorption on soils. Environ. Sci. Technol. 2013, 47, 3761. (25) Drits, V. A.; Silvester, E.; Gorshkov, A. I.; Manceau, A. Structure of synthetic monoclinic Na-rich birnessite and hexagonal birnessite: I. Results from X-ray diffraction and selected-area electron diffraction. Am. Mineral. 1997, 82, 946-961. (26) Wang, Q.; Yang, P.; Zhu, M. Structural transformation of birnessite by fulvic acid under anoxic conditions. Environ Sci Technol 2018, 52, 1844-1853. (27) Tian, L.; Shi, Z.; Lu, Y.; Dohnalkova, A. C.; Lin, Z.; Dang, Z. Kinetics of cation and oxyanion adsorption and desorption on ferrihydrite: roles of ferrihydrite binding sites and a unified model. Environ. Sci. Technol. 2017, 51, 10605-10614.

339 340

12

ACS Paragon Plus Environment

Page 12 of 16

Page 13 of 16

Environmental Science & Technology Letters

341

342 343 344 345 346 347 348 349

Figure 1. Kinetics of coupled As adsorption/desorption and oxidation on MnO2 at pH 7.0: (a) varying influent As(III) concentrations ([As(III) = 0.67 –5.71 µM, [MnO2] = 1 g L-1, Q = 2 mL min-1); (b) varying influent As(III) concentrations ([As(III) = 0.67 –5.71 µM, [MnO2] = 2 g L-1, Q = 2 mL min-1); (c) varying influent As(III) concentrations ([As(III) = 500 – 1500 µM, [MnO2] = 10 g L-1, Q = 2 mL min-1); and (d) varying flow rates ([As(III)] = 1000 µM, [MnO2] = 10 g L-1). The influent As(III) concentrations are shown in the figure. Symbols are experimental data and the lines are model calculations.

350

13

ACS Paragon Plus Environment

Environmental Science & Technology Letters

351 352 353 354 355 356 357

Figure 2. Kinetics of As(III) and As(V) adsorption on MnO2 during the coupled As adsorption/desorption and oxidation processes at pH 7.0: (a) influent [As(III)] = 0.67 – 5.71 µM, [MnO2] = 1 g L-1, and Q = 2 mL min-1; (b) influent [As(III)] = 0.67 – 5.71 µM, [MnO2] = 2 g L-1, and Q = 2 mL min-1, (c) influent [As(III)] = 500 – 1500µM, [MnO2] = 10 g L-1, and Q = 2 mL min-1; and (d) influent [As(III)] = 1000 µM, [MnO2] = 10 g L-1, and Q = 1-3 mL min-1. All lines are model calculations.

358

14

ACS Paragon Plus Environment

Page 14 of 16

Page 15 of 16

Environmental Science & Technology Letters

359 360 361 362

Figure 3. Changes in As(III) oxidation rate constants at various As(III) loadings on MnO2 during the kinetic processes. Solid lines are model calculations and the dashed line is the value reported by Ginder-Vogel et al. (2009).16

363

15

ACS Paragon Plus Environment

Environmental Science & Technology Letters

364

Table of Contents Graphic

365

16

ACS Paragon Plus Environment

Page 16 of 16