1026
T H E J O U R N A L OF I N D U S T R I A L A N D ENGINEERING C H E M I S T R Y
systems should bear only their proportion of the cost of treatment. The construction of a properly designed, economical and sanitary collection system is the first essential in sewage disposal. 4. The use of the separate system of sewer conduits has been abandoned as inadequate for urban districts. Polluted streams can be made pure by a system of interceptors to prevent sewage from reaching the streams. 5 . Rivers may be made clean and nuisances t o sight and smell may be prevented by simple screening or by screening and tankage treatment, provided the diluting volume of river flows and its velocity are sufficient to prevent deposits. Where not used as a water supply the extent to which a river may be used as an oxidizing agent thus offers a problem to be determined. 6. At the present stage of the art there is no process that gives better or cheaper results than the form of tank used a t the works of the Emscher Genossenschaft in *Germany. Should screening be desired, the so-called Reinsch screens as used a t Dresden, Germany, are the most cleanly and efficient of any observed. Experience has proved that adequate tankage treatment is more effective and less costly than the operation of fine screens. 7. Of the bacterial treatments, the percolating filter furnishes the best results both in oxidizing the organic matter and in the removal of putrescibility. The speed of operation is greater than by any other system, with consequent reduced first cost for land areas. 8. When sufficient fats are present in the sewage, they may be profitably recovered from sludge. Drying for fertilizer and fuel use has also proved profitable in some cases. 9. Submerged outlets from disposal works are essential for proper dilution. Disinfection with hypochlorite of lime as a final treatment is not in use either in England or Germany. I n the conditions of the rivers in the former country it would not be effective in removing pollution.
ACTION OF ALKALI AND SEA WATER ON CEMENTS The United States Bureau c& Standards has investigated the above subject and has published the results of its investigations in Bulletin 12. Since the physical test covered a period of exposure of not t o exceed 3l/1 years, ;he following conclusions drawn should be considered somewhat tentative : Portland cement mortar or concrete, if porous, can be disintegrated by the mechanical forces exerted by the crystallization of almost any salt in its pores, if a sufficient amount of i t is permitted to accumulate and a rapid formation of crystals is brought about by drying; as larger crystals are formed by slow crystallization, the same results would be obtained on a larger scale, but in greater time if the drying were slow. Porous stone, brick and other structural materials are disintegrated in the same manner. Hence, in alkali regions where a concentration of salts is possible, a dense non-porous surface is essential. While in the laboratory a hydraulic cement is readily decomposed if intimately exposed to the chemical action of various sulfate and chloride solutions, field inspection indicates that in service these reactions are much retarded if not entirely suspended in most cases, due probably to the carbonization of the lime of the cement near the surface or the formation of an impervious skin or protective coating by saline deposits. Properly made Portland cement concrete, when totally immersed, is apparently not subject to decomposition by the chemical action of sea water. It is not yet possible to state whether the resistance of cement t o chemical disintegration by sea water is due t o the superficial formation of an impervious skin or coating, which is subsequently assisted by the deposition of shells and moss forming a protective coating, or by the chemical reaction of the sea salts with the cement forming a more stable compound without disintegration
Vol.
j, No. 1 2
of the concrete, or by a combination of both of these phenomena. Marine construction, in so far as the concrete placed below the surface of the water is concerned, would appear to be a problem of method rather than materials, as the concrete sets and permanently hardens as satisfactorily in sea water as in fresh water or in the atmosphere, if it can be placed in the forms without undue exposure to the sea water while being deposited. Contrary to the opinion of many, there is no apparent relation between the chemical composition of a cement and the rapidity with which it reacts with sea water when brought into intimate contact. I n the presence of sea water or similar sulfate-chloride solutions, the most soluble element of the cement is the lime. If the lime of the cement is carbonated it is practically insoluble. The quantity of alumina, iron or silica present in the cement does not affect its solubility. The magnesia present in the cement is practically inert. The change which takes plwe in sea water when brought into intimate contact with the cement is as follows: The magnesia is precipitated from the sea water in direct proportion to the solubility of the lime of the cement. The sulfates are the most active constituents of the sea water, and are taken up by the cement. Their action is accelerated in the presence of chlorides. No definite sulfate compound was established. The quantity of chlorine and sodium taken up by the cement is so small that no statement can be made as t o the existence of any definite chloride or sodium compound formed with the cement. Metal reinforcement is not subject to corrosion if embedded t o a depth of 2 inches or more from the surface of well-made concrete.
ALLOYS OF ALUMINUM C. H. Ivinson, in the Mechanical Engineer, discusses the alloys of aluminum with the common and rare metals. An alloy of 4 per cent nickel has been shown to disintegrate in a very short time after being cast, but the introduction of copper is an advantage. Phosphide of copper added in quantitites of I . 5 per cent to a zinc-aluminum alloy containing from 1 2 . 5 t o 15 per cent zinc gives fluidity to the molten metal. Phosphide of zinc containing 2 5 per cent phosphorus may be substituted in the proportion of 0.05 per cent. This is one of the best fluxing and cleansing agents the writer knows for all aluminum alloys, and should be added to the molten alloy for a few minutes before pouring by wrapping in paper and plunging t o the bottom of the crucible by means of tongs and stirring briskly. Magnesium-aluminum alloys containing I to I O per cent magnesium are much improved by the addition of 5 per cent zinc, as 'this addition imparts better wearing properties t o the metal and aids in producing homogeneous castings. By the addition of I per cent phosphide of copper less oxidation of the metal takes place during the melting operations During the last few years metallurgists have been experimenting with some of the rarer metals, and this part of the subject is most interesting. The writer has alloyed aluminum with almost all the rarer metallic elements, such as cerium, neodymium, lanthanum, tantalum, zirconium, and beryllium, and some of these alloys gave most remarkable results even in quantities of only I per cent and under. Cerium and beryllium alloys are particularly interesting. An addition of 0 . 5 per cent of cerium raises the tensile strength of the metal from 4.5 tons per square inch to 1 0 . 3 tons per square inch, and gives an elongation of 8 . 5 per cent on z inches. This alloy was placed in sea water and boiled for 60 hours; the sample was carefully weighed before and after the boiling process, and there was no loss in weight. One side of the metal was polished and, after the boiling, was found to be untarnished. An alloy of 2 per cent