additive effects and a comparison with iron - American Chemical Society

Mar 6, 1985 - Figure 7. Differential molar heat of adsorption of CgH^CgH^. (OCH2CH2)9|10C)H onto activated carbon (CECA 1240) vs. the coverage degree...
0 downloads 0 Views 461KB Size
Langmuir 1986,2, 105-108

105

factant and the surface, which is microporous, partially hydrophobic, and with plenty of various chemical functions.16 The microscopic description of the adsorption mechanism is very difficult to understand and an attempt to explain it will be made in a future work. From comparison of the calorimetric results of the same surfactant molecules onto chemically different solid surfaces, we can do more adequate analysis of adsorption processes and mechanism.

1

e---0.25

0

0.5

0.75

. I

Conclusion The microcalorimetric device described here allows the determination of differential and integral molar heats of adsorption in all the range of coverage. Alternatively, it can also be used to obtain heats of dilution or heats of reaction in liquid phases. A very versatile unit is obtained by associating this device to the Calvet calorimeter. The high sensitivity, the large calorimetric cell (io0mL), and the variable stirring speed cope with a wide range of pH, physicochemical applications.

*

e

Figure 7. Differential molar heat of adsorption of C8Hl7C8H4(OCH2CH2)s,loOHonto activated carbon (CECA 1240) vs. the

coverage degree.

carbon. Figure 7 shows the differential molar heats of adsorption vs. 8. The enthalpic behavior is different from the previous one, since Ahadsdifvalues are always exothermic, suggesting direct interactions between the sur-

(16) Mattson, J. S.; Marc, H. B. In 'Activated Carbon, Surface Chemistry and Adsorption from Solution"; Dekker: New York, 1971; p 11.

Hydrogenation of Carbon Monoxide over Model Rhenium Catalysts: Additive Effects and a Comparison with Iron E. L. Garfunkel, J. Parmeter, B. M. Naasz, and G. A. Somorjai* Department of Chemistry, University of California, and Materials and Molecular Research Division, Lawrence Berkeley Laboratory, Berkeley, California 94720 Received March 6,1985. I n Final Form: September 12, 1985 Small area (approximately 1 cm2)rhenium and iron foil catalysts have been studied for CO hydrogenation reactions. Rhenium produces primarily methane and showed lower activity than iron. The addition of submonolayer amounts of alkali decreased the overall rate of reaction and caused a selectivity change toward longer chain hydrocarbons on both metal surfaces. Oxidation of the surface usually caused a higher selectivity toward methane and a decreased rate of carbon buildup, but the overall rate of methanation remained relatively constant. The hydrogenation of carbon or CH, fragments appears to be the rate-determining step in the reaction.

Introduction The hydrogenation of carbon monoxide to produce hydrocarbons a t a high rate and selectivity is under intensive study in many laboratories. Many different transition metals and transition-metal compounds have been identified as good catalysts to produce C1 molecules (methane, methanol),' high molecular weight liquid or oxygenated molecules (acetaldehyde and higher alcohol^).^ Often promotion by alkali yields increased molecular weight products and a lower concentration of methane?6 while transition-metal oxide catalysts produced more of the oxygenated specie^.^^^*' Rhenium has received relatively little attention as a catalyst in comparison with other transition metals. Nevertheless, rhenium has recently been shown to be a very active catalyst for ammonia synthesis.8 CO and N2 (1) Somorjai, G. A. Catal. Reu.-Sci. Eng. 1981,21, 189. (2) Bell, A. T. Catal. Rev-Sei. Eng. 1981,21, 203. (3)Watson, P.R,Somorjai, G. A. J. Catal. 1982, 74, 282. (4) Anderson, R. B. J. Catal. 1965,4, 56. (5) Weaner, D. A.; Ccener, F. P.; Bonzel, H. D. Langmuir 1985, I, 478. (6) Vannice, M. A. Catal. Reo-Sci. Eng. 1976, 14, 153.

I

bond scission is thought to be a prerequisite for both ammonia synthesis (N2/H2)and CO hydrogenation (CO/H2). Since iron is known to be active in both reactions and rhenium is active for the ammonia synthesis, it can be inferred that rhenium might also display good catalytic behavior for CO hydrogenation. In one survey study, promoted rhenium oxides on silica support were reported to have high selectivity for alcohol p r o d u ~ t i o n . ~ The purpose of this report is to explore the catalytic activity of rhenium metal foil for the hydrogenation of CO when clean and in the presence of alkali and oxygen and to compare its activity and selectivity with that of iron.

Experimental Section All work was performed in a combined ultrahigh-vacuum-

high-pressurecatalysis chamber shown schematically in Figure 1. In its UHV mode, the chamber was equipped with a double-pass CMA for Auger electron spectroscopy (AES),a UTI masa spectrometer for thermal desorption spectroscopy (TDS),an alkali deposition gun, an argon ion gun, and a molecular doser. While still positioned in the main chamber, the sample could be enclosed in a special high-pressure cell to allow reactions to be performed

(7) Natta, G.In "Catalysis"; Emmett, P. G., Ed, R a i i o l d New York,

1955; Vol. 3, 5.

(8)Spencer, N. D.; Somorjai, G. A. J. Catal. 1982, 78, 142.

(9) Tsunda Chern. Lett. 1981, 819.

0743-I463I86 I24Q2-QlQ5~Q1.5Q IO 0 1986 American Chemical Societv

106 Langmuir, Vol. 2, No. 1, 1986

Garfunkel et al.

Sampling Valve and LOOP

Polas GJr

Pressure Gouge

0

80

40

160

120 Time (min)

200

F m 2. Product accumulation curve for CO hydrogenation over rhenium foil; H2/C0 = 411, 1 atm. M e l h a n o t i o n Reaction

-.

I

SIDE VIEW W I T H HIGH PRESSURE CELL OPEN

Figure 1. High-pressure-low-pressure chamber for catalytic

surface studies.

at pressures as high as 10-20 atm. The iron foil was initially cleaned by first baking it in 1 atm of hydrogen (to help remove bulk S and C) and then by repeated sputtering in l@torr of argon while heat cycling between 400 and 800 "C. The rhenium sample was cleaned by heating the sample to 1000 O C in 5 X lo-' torr of oxygen for several minutes, followed by argon ion sputtering at 900 "C with intermittent annealing to 1300 "C. Both the rhenium and iron samples were given a final 5-min argon sputtering at room temperature followed by flashing to 1300 and 650 O C , respectively. This final heating was necessary to produce an atomically smooth surface-several reactions were run on surfaces that had not been annealed, and initial methanation rates were found to be as much as an order of magnitude greater than those from the flat surface. Sodium was deposited in vacuum from a "SAES getters" sodium gunlo mounted 3 cm from the sample. Oxygen was introduced at ca. 5 X lo-' torr to oxidize both the samples and the alkali adlayers. The alkali was readily oxidized at ambient temperature,while the clean rhenium and iron samples were heated at 800-900 and 400-500 "C, respectively, to enhance the rate of low-pressure oxidation. Oxidation could also be achieved by introducing water into the reaction cell before or during the reaction. Once the surface was prepared, the catalytic reaction chamber was clmed and a mixture of CO and H2gasea was introduced. The COH2ratio was 1:4 with a total pressure of 2 atm, except as noted. From room temperature, the sample was rapidly heated resistively to a given temperature (as monitored by a Pt/PtRh thermocouple wire) and gas samples were periodically introduced into the gas chromatograph by a sampling valve. Our chromatograph permitted the monitoring of hydrocarbons up to Cg. Following a run, which usually lasted from 1-5 h, the reaction chamber was evacuated to torr. Then the sample was exposed to UHV, and AES and TDS were used to examine the surface.

Results Figure 2 shows an example of the results of methane accumulation vs. time for a rhenium foil. The runs were characterized by a long stable period of constant reaction rate, which would eventually decay after several hours. As will be discussed below, this decline in the rate of methane (10) Garfunkel, R. G. Ph.D. Thesis, University of California, Berkeley, 1983.

\'p

\\Fe

1

4

Clean

Ea

\\A 24

Kcallmole

Fe+O 36

Kcallmole

Fe

1 .. -41

17

\ I 1

I

I

I9 20 I/T x 1 0 3

18

I

1

21

22

Figure 3. Arrhenius plot of methanation reaction on iron; CO/H2 = 32 psi. I

a

LL

o/ I I S

I

19

I/T

L

I

20

I

1

21

lo3

Figure 4. Arrhenius plot of methanation reaction on rhenium; CO/H2 = lI4, 32 psi.

formation is attributable t o the slow buildup of a carbonaceous layer which poisoned the surface. From the rate of methane production at various temperatures, Arrhenius plots were constructed. Figures 3 and 4 show Arrhenius plots for various runs on rhenium and iron foils. The slope of the plots allowed determination

Langmuir, Vol. 2, No. I, 1986 107

Hydrogenation of Carbon Monoxide

ethylene

CO H y d r o g e n a t i o n

CO Hydrogenation 5 4 0 K CO/H2’ 1/4

32

540 K , CO/H,= 1/4, 32 psi

DSi

ethylene

Re -Fe _ Turnover Frequency (mokcules/sildsec I

E,(CH41

kcal/mde

E,(C2Hql kcol/mole

2

5

28

24

2I

17

0methane

RetNo Fe

Re

Figure 5. Comparison of the selectivities for C1 and Cz species at 540 K (CO/Hz = 1/4,32 psi) over iron and rhenium foils. Product Selectivity Temperature Oependence for COHyampenofion on Rhenium Foli CO/H2: 1/4,

32 psi

100,

490K

515K

540K

590K I BL831-SO29

Figure 6. temperature dependence of the product selectivity for CO hydrogenation on rhenium foil; CO/Hz = l/.,, 32 psi. of the activation energies of the reactions. In addition by looking at the temperature at which the linear plot started to bend over we can see where rapid surface poisoning began, primarily due to carbon accumulation.” Methane was the dominant product on most initially clean rhenium samples that were studied. The activation energies and the selectivities of rhenium and iron foils are displayed in Figure 5. The turnover frequencies [ (molecules/site)/second] reported were the maximum values reached by the catalyst following an induction period (usually less than 20 min after initiation of the reaction). The turnover frequency listed assumed an active number of surface sites of 1015. Figure 6 shows how the selectivities changed as a function of temperature. As noted in Figure 5, the activation energy for ethylene formation was lower than that for methane. Thus methane production should be favored by higher temperatures, as was observed. The amount of carbon on the surface after a given run was a function of catalyst pretreatment, reaction temperature, and reaction time. Figure 7 shows the product distributions over the rhenium and iron surfaces following alkali and oxygen promotion. The general pattern observed with the alkali promoter was a change in selectivity toward higher molecular weight products as well as a decrease in the rate of methanation. The effect was more marked with rhenium than with iron, as clean iron already produces a large fraction of higher molecular weight species. Peroxidation of the surface caused an opposite effect to what was observed with the addition of sodium, a higher (11) (a) Goodman, D. W.; Kelley, R. D.; Madey, J. E.; Yates, J. T. J. Catal. 1980, 63, 226. (b) Campbell, C. T.; Goodman, D. W. Surf. Sci. 1982, 123,413.

I

n, FetNa 1480 K)

Reo,

FeO,

Figure 7. Effect of oxidation and alkali addition on product selectivity. selectivity toward methane. A problem occurred here concerning the number of active sites to be used in calculating turnover frequencies (in Figure 3). Oxidation tends to increase the surface area of the catalyst. In addition, the degree of oxidation changes throughout the reaction as a function of catalyst temperature, reaction time, and partial pressures. we believe, however, that our values are correct to within 50%, as our results are in good agreement with the behavior of industrial iron FischerTropsch catalysts.6

Discussion Rhenium metal appears to be a methanation catalyst that produces CHI at lower rates than either nickel or iron but with an activation energy that is similar to these two more active metals. Thus, the mechanism for producing methane is likely to be similar, i.e., CO dissociation followed by sequential hydrogenation of the carbon and the CH, fragments. The large carbon buildup on the rhenium surface indicates that CO dissociation is facile and also that the hydrogenation step is likely to be rate-determining. In this circumstance, a deuterium isotope effect is expected and experiments are in progress to ascertain its presence. The degree of carbon buildup on the samples was measured by AES. It was thus possible to distinguish between an active ”carbidic” carbon and an inactive “graphitic” one. This classification has been discussed extensively by other authors and results either from a comparison of the post-reaction carbon AES peak shape with known peak shapes of metal-carbide and -graphite surfaces5J1 or with corresponding XPS studies5 The overlayers also contained large amounts of adsorbed (or trapped) oxygen, hydrogen, and hydrocarbons, as was noticed in thermal desorption following the reaction. Therefore, the carbidic overlayer should not be considered as simply a surface or bulk metal carbide, but as a complex overlayer consisting of species where metal-carbon, carbon-hydrogen, and carbon-oxygen bonds exist. “Carbidic” carbon was the dominant surface species observed following low-temperature, short reaction time experiments. “Graphitic” carbon was dominant following high-temperature experiments or after flashing any post-reaction surface to >700 K. At this temperature, carbon-carbon bonding in graphitic layers covers much of the surface. On the iron catalyst the oxidation of the surface caused a significant change in the activation energy, as shown in Figure 3. This means that hydrogenation on this oxycarbide surface has a higher activation energy than on a metal surface. This may be expected since H addition is thought to be the rate-limiting step and metal dissociates and transfers H easier than carbon and oxygen. In general, the presence of alkali on the surface accelerated the rate of carbon buildup. A commonly invoked

108 Langmuir, Vol. 2, No. 1, 1986

h

3

Garfunkel et al.

I

100

300

500

700

900

1100

900

1100

0, E

+ C

I-

iI ' 100

'I'

2Fe 300

500

700

Figure 8. Auger spectra of a Bodium oxide promoted sample prior to (B) and following (A) a catalytic reaction.

model states that by lowering the dipole field at the surface, potassium allows the metal to more easily back donate into the CO 27r* antibonding ~ r b i t a l s , ' ~ Jthen ~ J ~ it can readily dissociate a t reaction temperatures. This results in increased atomic carbon on the surface and hence an increase in the carbon to hydrogen ratio. Consequently, the decreased overall reaction rates in the presence of the sodium can be explained by the change in carbon to hydrogen ratio, assuming that hydrogenation is the slow step.'l If CO dissociation were the rate-determining step, the presence of the alkali would likely result in an increased reaction rate. The altered surface carbon to hydrogen ratio can also explain the change in selectivity toward high molecular weight species. This should occur since the rate of carbon-carbon bond formation will be increased relative to the rate of carbon-hydrogen bond formation. In recent studies by Dwyer and Hardenbergh on iron foils and powders14J5it was shown that the poisoning of iron foils by carbon deposition was not observed for iron powders. Although the turnover frequencies on powders were lower than those observed on foils, they showed that even the bulk iron carbide (Fe5C2)powder created during a reaction displayed behavior on both unpromoted and alkali-promoted samples that was similar to known industrial reactivity (and that described in this work). In addition, they showed that the carbonaceous layers on iron powders contained more and longer hydrocarbon chains when alkali was used as a promoter. Another interesting observation was that only sodium, oxygen, and carbon (i.e., not rhenium or iron) were visible (12) Nieuwenhuys, B.E.Surf. Sci. 1981, 105, 505. (13) Luftman, H.; Sun, Y. M; White, J. M. Surf. Sci. 1984,139, 369. (14) Dwyer, D. J.; Hardenbergh, J . H. Appl. Surf. Sci., in press. (15) Dwyer, D. J.; Hardenbergh, J. H. J. Catal. 1981, 87, 66.

in the Auger spectra following several reactions (see Figure 8). This was also observed by Bonzel and Krebs,16 and they suggested that a potassium oxide layer was floating on top of a carbonaceous layer. We would further suggest that the alkali oxide (or suboxide) layer can itself play an important role in the catalytic reaction. Alkalis have long been useful as catalysts in the steam gasification of carbon sources. The possibility that the buildup of the carbonaceous layer is being hindered by the ability of alkalis to catalyze the reaction of water with carbon must be considered." Within this framework, alkali increases both the rate of CO dissociation (hence carbon buildup) and the rate of removal of the carbonaceous layer, once formed. The effect of preoxidation of the rhenium and iron surfaces depended upon the degree to which the surface was preoxidized and the temperature and time of the reaction. The extent of catalyst oxidation grew when water was introduced into the gas phase, allowing the surface to better resist the carbon buildup so apparent in most of the experiments. Although the initial reaction rates did not increase, the rate of poisoning was slower for oxidized surfaces. Another significant change induced by oxidation was the change in selectivity toward lower molecular weight species. By reducing both the amount of surface carbon and the number of adjacent metal atoms, the oxide surface does not permit extensive C-C bond formation. No significant amounts of oxygenates were detected over our low surface area rhenium and iron foils, in contrast to high surface area promoted industrial catalyst^.^^^^'

Conclusion Rhenium metal has been shown to be less active than iron and to have a relatively low selectivity toward higher molecular weight hydrocarbons. Thus rhenium acts more like nickel than iron in its CO hydrogenation behavior. Alkali monolayers decreased the reaction rates and changed the selectivity toward higher molecular weight species. These effects result from a higher carbon to hydrogen ratio on the surface. Our results are consistent with both the known industrial b e h a ~ i o r ~and , ~ ,recent ~ UHV experiments showing an increased tendency for CO to dissociate when alkali is c o a d ~ o r b e d . ~ J "The ~ ~ oxidation of the surface caused selectivity changes to lower molecular weight products. Acknowledgment. This work was jointly supported by the Director, Office Of Energy Research, Office of Basic Energy Sciences, Chemical Sciences Division of the U S . Department of Energy under Contract DE-AC0376SF00098,and Union Carbide under Grant Subcontract 04927. Registry No. CHI, 74-82-8;Re, 7440-15-5;Fe, 7439-89-6;Na, 7440-23-5. (16) Bonzel, H. D,;Krebs, H. J. Surf. Sci. 1981, 109, L527. (17) Wen, W. Y. Catal. Rev.-Sci. Eng. 1980, 22, 1. (18) Kiskanova, M.Surf. Sei. 1981, 111, 584. (19) Benziger, J.; Madix, R. J. Surf. Sci. 1980, 94, 119. (20) Crowell, J. E.;Garfunkel, E. L.; Somorjai, G. A. Surf. Sci. 1982, 121, 301.