Subscriber access provided by CORNELL UNIVERSITY LIBRARY
Article
Adsorption of estrogen contaminants by graphene nanomaterials under NOM preloading: Comparison with carbon nanotube, biochar and activated carbon Luhua Jiang, Yunguo Liu, Shaobo Liu, Guangming Zeng, Xinjiang Hu, Xi Hu, Zhi Guo, Xiao-fei Tan, Lele Wang, and Zhibin Wu Environ. Sci. Technol., Just Accepted Manuscript • Publication Date (Web): 11 May 2017 Downloaded from http://pubs.acs.org on May 12, 2017
Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.
Environmental Science & Technology is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.
Page 1 of 29
Environmental Science & Technology
1
Adsorption
2
nanomaterials under NOM preloading: Comparison with
3
carbon nanotube, biochar and activated carbon
4
Luhua Jiang,†,‡ Yunguo Liu,∗,†,‡ Shaobo Liu,*,§ Guangming Zeng,†,‡ Xinjiang Hu,ǁ Xi Hu,ǁ Zhi
5
Guo,†,‡ Xiaofei Tan,†,‡ Lele Wang,┴ Zhibin Wu†,‡
6 7 8 9 10 11 12 13 14
of
estrogen
contaminants
by
graphene
†
College of Environmental Science and Engineering, Hunan University, Changsha 410082, P.R.
China ‡
Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of
Education, Changsha 410082, P.R. China §
School of Metallurgy and Environment, Central South University, Changsha 410083, P. R. China
ǁ
College of Environmental Science and Engineering Research, Central South University of
Forestry and Technology, Changsha 410004, P. R. China ┴
Advanced Water Management Centre (AWMC), The University of Queensland, QLD 4072,
Australia
∗
Corresponding Author. Phone: +86 731 88649208. Fax: +86 731 88822829. E-mail:
[email protected] (Y.
Liu);
[email protected] (S. Liu).
ACS Paragon Plus Environment
Environmental Science & Technology
15
ABSTRACT: Adsorption of two estrogen contaminants (17β-estradiol and
16
17α-ethynyl estradiol) by graphene nanomaterials was investigated and compared
17
with those of a multi-walled carbon nanotube (MWCNT), a single-walled carbon
18
nanotube (SWCNT), two biochars, a powdered activated carbon (PAC), and a
19
granular activate carbon (GAC) in ultrapure water and in the competition of natural
20
organic matter (NOM). Graphene nanomaterials showed comparable or better
21
adsorption ability than carbon nanotubes (CNTs), biochars (BCs) and activated carbon
22
(ACs) under NOM preloading. The competition of NOM decreased the estrogens
23
adsorption by all adsorbents. However, the impact of NOM on the estrogens
24
adsorption was smaller on graphenes than CNTs, BCs and ACs. Moreover, the
25
hydrophobicity of estrogens also affected the uptake of estrogens. These results
26
suggested that graphenes nanomaterials could be utilized to removal estrogen
27
contaminants from water as an alternative adsorbent. Nevertheless, if transferred to
28
environment, they would also adsorb estrogen contaminants leading to great
29
environment hazards.
30
ACS Paragon Plus Environment
Page 2 of 29
Page 3 of 29
Environmental Science & Technology
31
TOC:
32
ACS Paragon Plus Environment
Environmental Science & Technology
33
Page 4 of 29
1. INTRODUCTION
34
Graphene, as a two-dimensional (2D) single-layer sheet of sp2-hybridized
35
conjugated carbon atoms, is a basic unit for construction of carbon allotropes such as
36
zero-dimensional
37
three-dimensional (3D) graphite.
38
attention since its discovery due to its unique structure and excellent electronic,
39
mechanical and optical properties.
40
graphene nanomaterial are expected to increase exponentially in the next decade. 7 An
41
additional unusual physical property of graphene nanomaterial compared with other
42
carbonaceous nanomaterials is a high specific surface area (SSA, 2,630 m2/g), and flat
43
morphology.
44
organic compounds. For examples, Pavagadhi et al. reported that graphene could be
45
used as an adsorbent to removal of algal toxins from water;
46
functionalized graphene oxide (GO) which could be an efficient adsorbent for
47
methylene blue (MB) removal from real wastewater. 11 Chen et al. found that reduced
48
graphene oxide (rGO) was a powerful adsorbent for removal of nitroaromatic
49
compounds from water. 12
8,9
(0D)
fullerenes, 1,2
3–6
one-dimensional
(1D)
nanotubes
or
Graphene has received the bulk of scientific
It has been reported these scale applications of
Therefore, they are expected to serve as excellent adsorbents for
10
Wu et al. prepared a
50
Estrogens, including 17β-estradiol (E2) and 17α-ethynyl estradiol (EE2), have
51
been identified to possess the serious endocrine disrupting activity among endocrine
52
disrupting chemicals (EDCs). As reported, they are capable of causing negative
53
responses to organisms even at low concentrations, such as sex reversal of males, fish
54
egg production inhibition, and collapse of local fish populations.
ACS Paragon Plus Environment
13,14
However, there
Page 5 of 29
Environmental Science & Technology
55
are only a small amount of peer-reviewed research articles on the uptake of estrogens.
56
15–18
57
adsorption of estrogens by this material has multiple important environmental
58
significances including evaluating (i) the potential of utilizing graphene nanomaterial
59
as adsorbent in pollution control, (ii) the fate and transportation of estrogens by
60
graphene nanomaterial in the environment, and (iii) the potential toxicological
61
impacts of graphene nanomaterial on the environment if this material is discharged
62
and adsorb estrogen pollutants.
Considering the predicted high-yield production of graphene, investigating
63
In natural waters, the adsorption behaviors of graphenes are likely to influence
64
by natural organic matter (NOM). NOM is ubiquitous in surface and ground waters,
65
originating
66
micro-organisms) and/or external (i.e., decomposition of plants, animal residues, and
67
terrestrial biomass) sources in waters.
68
chemically complex polyelectrolytes such as humic substances, proteins, hydrophilic
69
acids, lipids, carboxylic acids, carbohydrates, hydrocarbons, and amino acids.
70
Because of the carboxylic and phenolic moieties distributed throughout the entire
71
molecule, NOM generally carries a negative charge in in fresh waters.
72
presence of NOM may has definite impacts on the adsorption of estrogen
73
contaminants. As reported, there are two opposite impacts on organic contaminants
74
uptake: an increase in uptake because of the enhanced dispersion of adsorbent in the
75
presence of NOM and/or a decrease in uptake because of direct site competition
76
and/or pore blockage. 21 However, no attention has been paid to examine the influence
from
internal
(i.e.,
excretion
19
or
photosynthetic
products
of
NOM is a heterogeneous mixture of
ACS Paragon Plus Environment
20
Thus, the
Environmental Science & Technology
77
of NOM on estrogens adsorption although graphenes, carbon nanotubes (CNTs),
78
biochars (BCs), and activated carbon (ACs) have been utilized to explore the
79
adsorption properties of estrogens. Thus, the specific objectives of this research were
80
to (i) investigate the adsorption behavior of estrogen contaminants such as E2 and
81
EE2 onto graphene materials in ultrapure water and in the presence of NOM, and (ii)
82
compare the adsorption property of graphene nanomaterial with other common
83
carbonaceous adsorbent including multiwalled carbon nanotube (MWCNT),
84
single-walled carbon nanotube (SWCNT), two BCs, powdered activated carbon
85
(PAC), and granular activate carbon (GAC).
86
2. EXPERIMENTAL SECTION
87
Materials. The samples utilized in this research included two rGOs (rGO1 and
88
rGO2, laboratory preparation described in Supporting Information), CNTs (MWCNT
89
and SWCNT, Chengdu Organic Chemicals Co., Ltd.), two BCs (BC1 and BC2,
90
laboratory preparation described in Supporting Information), and ACs (PAC and GAC,
91
Sinopharm Chemical Reagent co., Ltd.). rGOs, CNTs, BCs and PAC were used as
92
obtained, while the GAC was smashed to 150-225 µm size before used.
93
E2 (≥ 98%) and EE2 (≥ 98%), two selected adsorbates in this research, were
94
purchased from Sigma-Aldrich Chemical Co. 3D molecular structures and selected
95
physical-chemical properties of the two compounds are listed in Table S1 and Fig. S1
96
in Supporting Information, respectively. Ultrapure water generated by a Milli-Q water
97
filtration system (Millipore, Billerica, MA) was applied to the preparation of all the
98
solutions.
ACS Paragon Plus Environment
Page 6 of 29
Page 7 of 29
Environmental Science & Technology
99
Humic acid (HA, Suwannee River II standard and Leonardite standard), fulvic
100
acid (FA, Suwannee River II standard and Nordic lake reference) were provided by
101
the International Humic Substances Society. NOM stock solution was prepared by
102
adding a known amount of HA and FA (weight ratio 1:1) into ultrapure water with
103
stirring 24 h. Dissolution of NOM was promoted by adding NaOH to increase the
104
solution pH to 7.
105
(SUVA254) and the dissolved organic carbon (DOC), the solution was diluted to
106
desired NOM concentration (see Table S2).
19
After measurements of the specific ultraviolet absorbance
107
Adsorbents characterization. Adsorbents were characterized by several
108
instrumental analyses to examine their physical-chemical properties, including
109
elemental analysis, zeta potential meter, Fourier transform infrared spectrum (FTIR),
110
and Brunauer-Emmett-Teller (BET) method. Oxygen contents of adsorbents was
111
examined using an elemental analyzer (Vario EL III, Elementar, Germany). Zeta
112
potential measurements were performed with a zeta potential meter (Zetasizer
113
Nano-ZS90, Malvern). Besides, pH of the point of zero charge (pHPZC) of adsorbents
114
was investigated via pH equilibration technique.
115
conducted by using Nicolet 5700 Spectrometer in KBr pellet at room temperature.
116
The porosities of the samples were determined at liquid nitrogen temperature using a
117
surface area and porosity analyzer (Micromeritics, ASAP 2020 M+C) after evacuation
118
of the samples at 150 oC for 12 h. The BET equation was applied to calculate specific
119
surface area (SSA). The total pore volumes (PV) were determined from the adsorbed
120
volume of N2 near the saturation point (P/Po = 0.99). Pore size distributions (PSD) of
22
FTIR measurements were
ACS Paragon Plus Environment
Environmental Science & Technology
Page 8 of 29
121
samples were obtained from the N2 isotherms via using the Density Functional Theory
122
(DFT) model.
123
Batch adsorption experiments. The stock solutions were prepared by
124
dissolving appropriate amount of E2 and EE2 in methanol, respectively. Constant
125
dose batch adsorption isotherms for E2 and EE2 were performed through a 250 mL
126
amber glass bottles with Teflon-lined screw caps. Two kinds of isotherm experiments
127
were carried out at room temperature (25 ± 1 oC).
128
For ultrapure water experiments, bottles with about 1 mg of adsorbents were first
129
filled with ultrapure water to nearly no free headspace. Afterward, known volumes of
130
estrogens stock solutions were directly spiked into the bottles. For the graphene
131
experiments, the bottles with samples were first half filled with ultrapure water. After
132
ultrasonicated for 30 min, the bottles nearly filled with ultrapure water before spiking
133
estrogens. The volume percentage of the methanol in spiked solution was remained
134
below 0.1% (v/v) to avoid the co-solvent effect, as used by reported articles.
135
According to our group’s researches, 24 h was sufficient to reach equilibrium for
136
estrogens adsorption. 26,27 Therefore, the prepared bottles were placed in a shaker bath
137
with an agitation speed of 170 rpm for 24 h. The initial pH values in aqueous
138
solutions kept around 6.5. The desired solution pH was adjusted by negligible
139
volumes of HCl and NaOH solution through a pH meter (PHSJ-5, China).
23–25
140
The NOM influence on estrogen adsorptions by selected adsorbents was
141
investigated under preloading condition. Specifically, NOM was added four days in
142
advance before spiking estrogens, which stood for severe competition of NOM. To
ACS Paragon Plus Environment
Page 9 of 29
Environmental Science & Technology
143
examine the effect of preloading NOM on adsorption, bottles with about 1 mg
144
samples were initially nearly filled with 3.4 mg DOC/L NOM stock solution which
145
buffered with 1 mM NaH2PO4 H2O/Na2HPO4 7H2O and adjusted pH to 7.0. Further,
146
the bottles were placed in a shaker bath with an agitation speed of 170 rpm for four
147
days. The residual NOM was examined using DOC analysis through a Shimadzu
148
TOC-VCPH analyzer (Shimadzu Co., Japan). After that, the bottles were directly
149
spiked with known volumes of estrogens stock solutions, and then continuously
150
shocked for 24 h.
151
Analyses. After adsorption for a predetermined time, the solutions (10 mL) were
152
separated from the adsorbents by centrifugation. The estrogens concentration in
153
supernatants were measured by high-performance liquid chromatography (HPLC)
154
with fluorescence detectors (Agilent 1100 Series, USA). The analytical column was
155
C18 reverse-phase column (5 mm, 4.6 × 150 mm, Agilent). The mobile phase flow
156
rate was set at 1 mL/min, and the column temperature was kept at 30 oC, and the
157
sample injection volume was 20 µL. The mobile-phase solvent profile was 45%
158
ultrapure water acidified with 10 mM H3PO4 and 55% methanol. Then detection was
159
carried out at an excitation wavelength of 280 nm and an emission wavelength of 310
160
for both E2 and EE2. Furthermore, bottles without any adsorbents were served as
161
blanks to monitor the loss of adsorbates during the experiment, which was found to be
162
negligible. The description of the HPLC method used in this research has been
163
reported elsewhere. 28,29
164
Isotherm modeling. In this work, four common nonlinear isotherm models, such
ACS Paragon Plus Environment
Environmental Science & Technology
Freundlich
(FM),
Langmuir
(LM),
Page 10 of 29
165
as
Langmuir-Freundlich
(LFM)
and
166
Polanyi-Manes models (PMM), were applied to interpret the adsorption isotherm data
167
(Table S3). The residual root-mean-square error (RMSE), chi-square test (χ2) and
168
coefficient of determination (R2) values suggested that FM showed goodness of fitting
169
the experimental data (Table S4-S5). Thus, FM parameters were utilized to evaluate
170
adsorption data further.
171
3. RESULTS AND DISCUSSION
172
Adsorbent characterization. The selected physicochemical properties of all
173
adsorbents, such as SSA, PV, PSD and oxygen content, were listed in Table 1. As can
174
been seen, rGO1 had higher oxygen content (16.69 %) than rGO2 (10.33 %); and the
175
SSA of rGO1 and rGO2 were 244 and 147 m2/g, respectively, which indicated that the
176
SSA of rGOs was considerably enhanced after exfoliation of graphite (4.5 m2/g).
177
However, the SSA gap between this obtained value and the theoretical maximum
178
value of thin graphene (single-layered graphene, 2630 m2/g)
179
aggregation tendency of graphene layers during the reduction process due to the
180
strong van der Waals force between single graphene layers. Consequently, they
181
formed bundles resulting in decreasing the SSA. Although the aggregation
182
characteristics might change the SSA, rGOs had increasing distribution of micropores
183
( PAC >
193
SWCNT > rGO1 > MWCNT > rGO2 > BC2 > BC1. As reported, micropores had
194
higher surface area than that of the mesopores and macropores.
195
pores in the rGOs, CNTs, and BCs resulted in relatively smaller SSA than those of
196
ACs. Besides, the N2 adsorption isotherms of these adsorbents are shown in Fig. S3.
197
In terms of physical structures, as illustrated by the nitrogen adsorption isotherms,
198
ACs and BCs were microporous adsorbents. However, SWCNT and rGO exhibited
199
both microporous and mesoporous properties. Furthermore, the isotherm pattern of
200
the MWCNT suggested that it is abundant in macropores, and it has less micropores
201
and mesopores than the SWCNT and rGO. It is reported that the adsorption behavior
202
in micropores depend not only on the fluid-wall interactions but also on the attractive
203
forces between fluid molecules, resulting in capillary (pore) condensation.
204
addition, the FTIR analysis (Fig. S2) illustrated the existence of C-O group at 1096
205
cm-1, C=O group at 1641 cm-1, and O-H group at 3443 cm-1 on rGOs, CNTs, BCs, and
206
ACs.
32
Thus, the larger
33
In
207
Adsorption of E2 and EE2 by graphene nanomaterials in ultrapure water.
208
Adsorption isotherms of E2 and EE2 in ultrapure water are exhibited in Fig. 1, and the
ACS Paragon Plus Environment
Environmental Science & Technology
209
according Freundlich isotherm parameters are listed on Table 2. Kd values (qe/Ce), as
210
the single point adsorption descriptors, were also calculated at different equilibrium
211
concentrations such as at 0.1%, 1%, 10% and 25% of estrogens aqueous solubility,
212
respectively, and listed in Table S6. Clearly, adsorption capacities for EE2 were lower
213
than E2 for all adsorbents, as represented by KF of Freundlich model. This might be
214
ascribed to the higher hydrophobicity of E2 than EE2 as reflected by the higher
215
octanol-water distribution coefficient (LogKow) value of E2 (Table S1). To further
216
examine the effect of hydrophobic interaction in adsorption, two parameters (KF-Csw
217
and KF-LogKow ) as the solubility normalized and hydrophobicity normalized KF values,
218
respectively, were applied (Table S7). As illustrated, the difference for KF-Csw and
219
KF-LogKow between E2 and EE2 was narrowed. Nevertheless, these parameters were
220
not nearly the same after above normalization. Thus, although hydrophobic
221
interaction was influential on adsorption, it was not the sole factor affecting estrogens
222
uptake.
223
In addition, rGO2 showed higher E2 and EE2 adsorption ability than rGO1 even
224
after SSA normalization. This might be attributed to the more non-polar surface of
225
rGO2 due to the less oxygen content. As reported, oxygen containing functional
226
groups of adsorbents could reduce the accessibility for hydrophobic organic
227
compounds via decreasing the available number of adsorption sites because of the
228
formation of water clusters on the their surface.
229
found in the uptake of aromatic organic and halogenated aliphatic contaminants by
230
graphene materials.
7,35,36
34
Similar phenomenon was also
In order to further investigate the difference between rGO1
ACS Paragon Plus Environment
Page 12 of 29
Page 13 of 29
Environmental Science & Technology
231
and rGO2 uptake, Kd values at different equilibrium concentrations were also
232
investigated (Table S6). With increasing equilibrium concentrations, the gaps in
233
estrogens uptake between rGO1 and rGO2 narrowed, which might be ascribed to the
234
stronger hydrophobic effect and π-π interactions between estrogen contaminants and
235
the graphene surface. Thus, with increasing estrogen concentrations, a number of
236
water molecules which were clustered around the oxygen containing functional
237
groups might be displaced by estrogen molecules and then the estrogen molecules
238
could be better coated on the surface of graphene nanosheets.
239
Comparison of E2 and EE2 adsorption by rGOs, CNTs, BCs and ACs in
240
ultrapure water. Compared graphenes with other carbonaceous nanomaterials, the
241
order of both E2 and EE2 adsorption abilities was provided (PAC > SWCNT > rGO2 >
242
rGO1 > MWCNT > GAC > BC2 > BC1) as illustrated by KF. This suggested that the
243
adsorption of estrogens seriously depended on the physiochemical characteristics of
244
carbonaceous nanomaterials. To investigate the effect of surface area of all the
245
adsorbents, SSA normalization were investigated (Table 2 and Fig. 1). Two
246
parameters, KF-SSA and RSSA, as the surface area normalized KF values and the ratio of
247
KF-SSA to KF, respectively, were analyzed to quantify the effect of SSA on the
248
estrogens uptake by various adsorbents. The lower RSSA value exhibited a greater
249
impact of SSA on adsorption. As illustrated, the differences in KF-SSA were suppressed
250
after SSA normalization. In particular, the gap between BCs and other adsorbents was
251
obviously narrowed, indicating SSA was a great factor influencing estrogens uptake
252
by BCs. In addition, RSSA values of ACs and SWCNT were smaller than other
ACS Paragon Plus Environment
Environmental Science & Technology
253
adsorbents, which reflected stronger decrease in the estrogens uptake by ACs and
254
SWCNT. This suggested that SSA played an important role in the uptake of estrogens.
255
Furthermore, the adsorption isotherms were further normalized on the basis of oxygen
256
content. As can be seen, notable differences still observed among these isotherms (Fig.
257
1). Interestingly, microporous adsorbents (ACs, SWCNT and rGOs) still exhibited
258
higher E2 and EE2 adsorption after SSA and oxygen content normalization, which
259
might be attributed to the desirable filling of micropores by estrogen molecules. These
260
investigations suggested that the factors affecting estrogens uptake by graphene
261
materials in ultrapure water were similar to those of CNTs, BCs, and ACs. These
262
results demonstrated that the overall adsorption behavior of these adsorbents relied on
263
their SSA, PSD, oxygen content, and hydrophobicity of estrogens.
264
Adsorption of E2 and EE2 by graphene nanomaterials under NOM
265
preloading. To study the influence of NOM on estrogens adsorption by graphene
266
nanomaterials, adsorption of E2 and EE2 by rGOs were investigated under NOM
267
preloading. The adsorption isotherms in the presence of NOM are illustrated in Fig. 2.
268
For comparison, isotherms of graphenes in ultrapure water are also exhibited in the
269
same figure. Freundlich isotherm parameters in NOM solution are also summarized in
270
Table 2. KF-NOM and RNOM, as KF values of adsorption in NOM solution and the ratio
271
of KF-NOM to KF, respectively, were used to quantify the influence of NOM on the
272
estrogens adsorption by different adsorbents. The lower RNOM values suggest a greater
273
reduction of adsorption ability because of the presence of NOM. The percent
274
reduction (RKd ) in Kd value in the presence of NOM, as compared to Kd in ultrapure
ACS Paragon Plus Environment
Page 14 of 29
Page 15 of 29
Environmental Science & Technology
275
water, were also investigated (Table S6). Previous studies reported that NOM with
276
higher aromatic content and lower polarity tend to sorb on aromatic moieties of
277
graphene materials presumably through π-π interactions and/or hydrophobic
278
interactions. 37–39 Adsorption of E2 and EE2 by graphene nanomaterials reduced in the
279
presence of NOM, which might suggest the direct competition between NOM
280
contaminants with E2 and EE2 for the available uptake sites on aromatic moieties of
281
rGOs. In addition, as indicated by lower RNOM values of rGO2, influence of NOM on
282
adsorption capacity of rGO2 were stronger than rGO1. Meanwhile, rGO1 showed
283
comparable adsorption capacity under NOM preloading condition and in ultrapure
284
water as exhibited by RNOM values (68.9% and 60.5%) of rGO1 for E2 and EE2,
285
respectively. These observations might be ascribed to (i) the electrostatic repulsive
286
force between acidic charged rGO1 surface (pHPZC=4.8, Table 1) and negatively
287
charged NOM molecules resulting in less NOM aligning on the rGO1 surface as
288
reflected by Table S8, (ii) the better dispersed rGO1 nanosheets due to the polarity of
289
surface oxides which led to decreasing the effect of NOM on estrogens adsorption in
290
water, and (iii) the reduced hydrophobicity of rGO2 because NOM preloading
291
introduced more polar functionalities and negative charges on the rGO2 as illustrated
292
by lower pHPZC of rGO2 after NOM preloading (Table 1). The N value of Freundlich
293
model suggests the heterogeneity of the surface; and a higher N value exhibits a
294
homogeneous surface with narrow distributions of adsorption site.
295
the N values of rGO2 was 37% for E2 and 12% for EE2, while the increase in N
296
values of rGO1 was 27% and 25%, respectively. Small enhancements in the N values
ACS Paragon Plus Environment
40
The increase in
Environmental Science & Technology
Page 16 of 29
297
indicated the NOM aligning did not notably alter the surface heterogeneity of
298
graphene nanomaterials. Moreover, the RNOM as a result of NOM preloading in E2
299
uptake was higher than the EE2 for rGOs, which might be ascribed to the stronger
300
hydrophobic effect of E2 molecule than EE2 molecule to graphene nanomaterials.
301
Comparison of E2 and EE2 adsorption by rGOs, CNTs, BCs and ACs under
302
NOM preloading. Adsorption of estrogens by rGOs, CNTs, BCs, and ACs in the
303
presence of NOM was also compared (Table 2 and Fig. 2). The order of E2 adsorption
304
capacity indicated by KF-NOM was PAC > SWCNT > rGO1 > rGO2 > MWCNT >
305
GAC > BC2 > BC1; the order of EE2 adsorption capacity indicated by KF-NOM was
306
PAC > rGO2 > SWCNT > rGO1 > MWCNT > GAC > BC2 > BC1. These findings in
307
the presence of NOM illustrated that in terms of engineering application, graphene
308
nanomaterials showed comparable or better adsorption ability than CNTs, BCs, and
309
ACs, thus they could considered as alternative adsorbents for eliminating estrogen
310
contaminants from aqueous solution; and in terms of environmental implication, if
311
transferred to environment, they would enrich estrogen contaminants leading to great
312
environment hazards.
313
Past researches reported that the attractive interactions between NOM and CNTs, 19,41–43
314
BCs and ACs are largely driven by π-π and hydrophobic interactions.
315
addition, the adsorption capacity, especially of ACs, is also determined by SSA of
316
porous structure available for adsorption.
317
and EE2 of rGOs were higher than that of CNTs, BCs, and ACs, which suggested that
318
the influence of NOM preloading condition on rGOs was lower than that on CNTs,
44,45
In
As illustrated in Table 2, RNOM for E2
ACS Paragon Plus Environment
Page 17 of 29
Environmental Science & Technology
319
BCs, and ACs. NOM preloading could reduce the pHPZC of all samples as exhibited in
320
Table 1, which facilitated formation of water clusters through adsorbing water to
321
hydrophilic sites causing less available for the hydrophobic estrogens. The order of
322
pHPZC after NOM preloading was CNTs < rGOs < BCs~ACs, which could explain the
323
higher influence of NOM preloading on BCs and ACs than rGOs. Besides, as reported
324
by Newcombe et al., pore blockage, especially for micropore, caused by NOM can be
325
also expected to decrease the adsorption capacity through restricting access to
326
adsorption sites for the target contaminants. 46 Comparison with ACs, rGOs possessed
327
much less microporous structure, which resulting in less hindrance of estrogens access
328
to the adsorption sites. As presented by Table S8, the adsorbed mount of NOM on
329
CNTs was higher than that of rGOs after four days preloading, due to lower oxygen
330
content which was prone to adsorption through π-π interactions and hydrophobic
331
interactions. This indicated that less adsorption sites was taken placed by NOM on
332
rGOs as compared to CNTs, which resulted in less effect of NOM preloading on rGOs.
333
Furthermore, it has been reported that CNTs are more hydrophobic compared with
334
rGOs as reflected by Table 1 and prefer to aggregation as compact bundles due to the
335
unavoidable van der Waals interactions along the length axis.
336
compact bundle structure for graphene nanomaterials resulted in lower influence of
337
NOM preloading condition on rGOs comparison with CNTs. Similar phenomenon
338
was also found in the adsorption of aromatic organic and halogenated aliphatic
339
contaminants.
340
decrease in adsorbate equilibrium concentrations. This suggested that NOM
7,35,36
47,48
The much less
Furthermore, as indicated by Table S6, RKd increased with
ACS Paragon Plus Environment
Environmental Science & Technology
341
molecules preferentially took up high energy adsorption sites; and then the
342
replacement of binded NOM molecules would be harder with enhancing estrogen
343
concentrations, considering that the NOM concentration of 3.4 mg DOC/L (Table S2)
344
selected to preloading was 2-3 orders of magnitude higher than estrogens at the low
345
concentration ranges. Moreover, as exhibited by increasing Freundlich N values
346
(Table 2), surface heterogeneity of all samples reduced during NOM preloading.
347
Nevertheless, there were no significant trends observed in the enhancing N values.
348
Among all samples, ACs was affected the most under NOM preloading. As indicated
349
by RKd values in Table 2, the reductions of estrogens adsorption by ACs in the
350
presence of NOM was maintained at a high level (>50%) at all the different
351
equilibrium concentrations. This clear decrease might be ascribed to the microporous
352
structure of ACs, where NOM preloading might led to a combination of pore
353
condensation and site competition for estrogens uptake.
354
ASSOCIATED CONTENT
355
Supporting Information
356
Preparation of reduced graphene and biochar. Selected properties of estrogens (Table
357
S1), characteristics of NOM solution (Table S2), nonlinear adsorption isotherm
358
models (Table S3), nonlinear simulations of adsorption isotherms in ultrapure water
359
and NOM solution (Table S4 and S5), single point adsorption coefficients (Kd) for
360
different levels of E2 and EE2 water solubilities of ultrapure water and NOM solution
361
isotherms (Table S6), the solubility normalized and hydrophobicity normalized KF
362
values (KF-Csw and KF-LogKow ) of estrogens adsorption in ultrapure water (Table S7),
ACS Paragon Plus Environment
Page 18 of 29
Page 19 of 29
Environmental Science & Technology
363
the NOM adsorption capacities after four days preloading (Table S8), the 3D
364
molecular configurations of E2 and EE2 (Fig. S1), FTIR spectrums of the rGOs,
365
CNTs, ACs, and BCs (Fig. S2), and nitrogen adsorption isotherms of the rGOs, CNTs,
366
ACs, and BCs (Fig. S3). This material is available free of charge via the Internet at
367
http://pubs.acs.org.
368 369
Notes
370
The authors declare no competing financial interest.
371
ACKNOWLEDGEMENTS
372
This work was supported by the National Natural Science Foundation of China
373
(Grants Nos. 51521006, 51609268 and 51608208), the Hunan Provincial Innovation
374
Foundation for Postgraduate (Grant No. CX2016B135), and the Key Project of
375
Technological Innovation in the Field of Social Development of Hunan Province,
376
China (Grant Nos. 2016SK2010 and 2016SK2001).
ACS Paragon Plus Environment
Environmental Science & Technology
REFERENCES (1)
Hu, X.; Wang, H.; Liu, Y. Statistical Analysis of Main and Interaction Effects on Cu (II) and Cr (VI) Decontamination by Nitrogen–Doped Magnetic Graphene Oxide. Sci. Rep. 2016, 6, 34378.
(2)
Geim, A. K.; Novoselov, K. S. The rise of graphene. Nat. Mater. 2007, 6 (3), 183–191.
(3)
Lee, C.; Wei, X.; Kysar, J. W.; Hone, J. Measurement of the elastic properties and intrinsic strength of monolayer graphene. Science 2008, 321 (5887), 385–388.
(4)
Balandin, A. A.; Ghosh, S.; Bao, W.; Calizo, I.; Teweldebrhan, D.; Miao, F.; Lau, C. N. Superior thermal conductivity of single-layer graphene. Nano Lett. 2008, 8 (3), 902–907.
(5)
Meyer, J. C.; Geim, A. K.; Katsnelson, M. I.; Novoselov, K. S.; Booth, T. J.; Roth, S. The structure of suspended graphene sheets. Nature 2007, 446 (7131), 60–63.
(6)
Latil, S.; Henrard, L. Charge Carriers in Few-Layer Graphene Films. Phys. Rev.
Lett. 2006, 97 (3), 036803. (7)
Zhou, Y.; Apul, O. G.; Karanfil, T. Adsorption of halogenated aliphatic contaminants by graphene nanomaterials. Water Res. 2015, 79, 57–67.
(8)
Behabtu, N.; Lomeda, J. R.; Green, M. J.; Higginbotham, A. L.; Sinitskii, A.; Kosynkin, D. V; Tsentalovich, D.; Parra-Vasquez, A. N. G.; Schmidt, J.; Kesselman, E. Spontaneous high-concentration dispersions and liquid crystals of graphene. Nat. Nanotechnol. 2010, 5 (6), 406–411.
(9)
Park, S.; Ruoff, R. S. Chemical methods for the production of graphenes. Nat.
Nanotechnol. 2009, 4 (4), 217–224. (10)
Pavagadhi, S.; Tang, A. L. L.; Sathishkumar, M.; Loh, K. P.; Balasubramanian, R. Removal of microcystin-LR and microcystin-RR by graphene oxide: adsorption and kinetic experiments. Water Res. 2013, 47 (13), 4621–4629.
(11)
Wu, Z.; Zhong, H.; Yuan, X.; Wang, H.; Wang, L.; Chen, X.; Zeng, G.; Wu, Y.
ACS Paragon Plus Environment
Page 20 of 29
Page 21 of 29
Environmental Science & Technology
Adsorptive removal of methylene blue by rhamnolipid-functionalized graphene oxide from wastewater. Water Res. 2014, 67, 330–344. (12)
Chen, X.; Chen, B. Macroscopic and Spectroscopic Investigations of the Adsorption of Nitroaromatic Compounds on Graphene Oxide, Reduced Graphene Oxide, and Graphene Nanosheets. Environ. Sci. Technol. 2015, 49 (10), 6181–6189.
(13)
Pan, B.; Lin, D.; Mashayekhi, H.; Xing, B. Adsorption and hysteresis of bisphenol A and 17α-ethinyl estradiol on carbon nanomaterials. Environ. Sci.
Technol. 2008, 42 (15), 5480–5485. (14)
Zhang, Y.; Zhou, J. L. Removal of estrone and 17β-estradiol from water by adsorption. Water Res. 2005, 39 (16), 3991–4003.
(15)
Yoon, Y.; Westerhoff, P.; Snyder, S. A.; Esparza, M. HPLC-fluorescence detection and adsorption of bisphenol A, 17β-estradiol, and 17α-ethynyl estradiol on powdered activated carbon. Water Res. 2003, 37 (14), 3530–3537.
(16)
Lee, J.; Bartelt-Hunt, S. L.; Li, Y.; Morton, M. Effect of 17β-estradiol on stability and mobility of TiO2 rutile nanoparticles. Sci. Total Environ. 2015,
511, 195–202. (17)
Han, J.; Qiu, W.; Meng, S.; Gao, W. Removal of ethinylestradiol (EE2) from water via adsorption on aliphatic polyamides. Water Res. 2012, 46 (17), 5715–5724.
(18)
Fukuhara, T.; Iwasaki, S.; Kawashima, M.; Shinohara, O.; Abe, I. Adsorbability of estrone and 17β-estradiol in water onto activated carbon.
Water Res. 2006, 40 (2), 241–248. (19)
Hyung, H.; Kim, J. H. Natural organic matter (NOM) adsorption to multi-walled carbon nanotubes: effect of NOM characteristics and water quality parameters. Environ. Sci. Technol. 2008, 42 (12), 4416–4421.
(20)
Bhatnagar, A.; Sillanpää, M. Removal of natural organic matter (NOM) and its constituents from water by adsorption–A review. Chemosphere 2017, 166, 497–510.
(21)
Pan, B.; Zhang, D.; Li, H.; Wu, M.; Wang, Z.; Xing, B. Increased adsorption of
ACS Paragon Plus Environment
Environmental Science & Technology
sulfamethoxazole on suspended carbon nanotubes by dissolved humic acid.
Environ. Sci. Technol. 2013, 47 (14), 7722–7728. (22) Guedidi, H.; Reinert, L.; Lévêque, J. M.; Soneda, Y.; Bellakhal, N.; Duclaux, L. The effects of the surface oxidation of activated carbon, the solution pH and the temperature on adsorption of ibuprofen. Carbon 2013, 54, 432–443. (23)
Chen, J.; Chen, W.; Zhu, D. Adsorption of nonionic aromatic compounds to single-walled carbon nanotubes: effects of aqueous solution chemistry. Environ.
Sci. Technol. 2008, 42 (19), 7225–7230. (24)
Zhang, S.; Shao, T.; Bekaroglu, S. S. K.; Karanfil, T. Adsorption of synthetic organic chemicals by carbon nanotubes: effects of background solution chemistry. Water Res. 2010, 44 (6), 2067–2074.
(25)
Wang, J.; Chen, Z.; Chen, B. Adsorption of Polycyclic Aromatic Hydrocarbons by Graphene and Graphene Oxide Nanosheets. Environ. Sci. Technol. 2014, 48 (9), 4817–4825.
(26)
Jiang, L. H.; Liu, Y. G.; Zeng, G. M.; Xiao, F. Y.; Hu, X. J.; Hu, X.; Wang, H.; Li, T. T.; Zhou, L.; Tan, X. F. Removal of 17β-estradiol by few-layered graphene oxide nanosheets from aqueous solutions: External influence and adsorption mechanism. Chem. Eng. J. 2016, 284, 93–102.
(27)
Jiang, L.; Liu, Y.; Liu, S.; Hu, X.; Zeng, G.; Hu, X.; Liu, S.; Liu, S.; Huang, B.; Li, M. Fabrication of β-cyclodextrin/poly (L-glutamic acid) supported magnetic graphene oxide and its adsorption behavior for 17β-estradiol. Chem.
Eng. J. 2017, 308, 597–605. (28)
Joseph, L.; Heo, J.; Park, Y.-G.; Flora, J. R. V; Yoon, Y. Adsorption of bisphenol A and 17α-ethinyl estradiol on single walled carbon nanotubes from seawater and brackish water. Desalination 2011, 281, 68–74.
(29)
Qin, C.; Troya, D.; Shang, C.; Hildreth, S.; Helm, R.; Xia, K. Surface Catalyzed Oxidative Oligomerization of 17β-Estradiol by Fe3+-Saturated Montmorillonite. Environ. Sci. Technol. 2014, 49, 956–964.
(30)
Pignatello, J. J. Characterization of Aromatic Compound Sorptive Interactions with Black Carbon (Charcoal) Assisted by Graphite as a Model. 2005, No. 203,
ACS Paragon Plus Environment
Page 22 of 29
Page 23 of 29
Environmental Science & Technology
2033–2041. (31)
Kim, T.; Jung, G.; Yoo, S.; Suh, K. S.; Ruoff, R. S. Activated graphene-based carbons as supercapacitor electrodes with macro-and mesopores. ACS Nano 2013, 7 (8), 6899–6905.
(32)
Zhang, S.; Shao, T.; Kose, H. S.; Karanfil, T. Adsorption of aromatic compounds by carbonaceous adsorbents: a comparative study on granular activated carbon, activated carbon fiber, and carbon nanotubes. Environ. Sci.
Technol. 2010, 44 (16), 6377–6383. (33)
Lowell, S.; Shields, J. E.; Thomas, M. A.; Thommes, M. Characterization of Porous Solids and Powders: Surface Area, Pore Size and Density. Part.
Technol. 2006, 16 (9), 1620. (34)
Sigmund, G.; Sun, H.; Hofmann, T.; Kah, M. Predicting the Sorption of Aromatic Acids to Noncarbonized and Carbonized Sorbents. Environ. Sci.
Technol. 2016, 50 (7), 3641–3648. (35)
Apul, O. G.; Wang, Q.; Zhou, Y.; Karanfil, T. Adsorption of aromatic organic contaminants by graphene nanosheets: Comparison with carbon nanotubes and activated carbon. Water Res. 2013, 47 (4), 1648–1654.
(36)
Ersan, G.; Kaya, Y.; Apul, O. G.; Karanfil, T. Adsorption of organic contaminants by graphene nanosheets, carbon nanotubes and granular activated carbons under natural organic matter preloading conditions. Sci. Total Environ. 2016, 565, 811–817.
(37)
Zhang, J.; Gong, J. L.; Zenga, G. M.; Ou, X. M.; Jiang, Y.; Chang, Y. N.; Guo, M.; Zhang, C.; Liu, H. Y. Simultaneous removal of humic acid/fulvic acid and lead from landfill leachate using magnetic graphene oxide. Appl. Surf. Sci. 2016, 370, 335–350.
(38)
Niederer, C.; Schwarzenbach, R. P.; Goss, K. U. Elucidating differences in the sorption properties of 10 humic and fulvic acids for polar and nonpolar organic chemicals. Environ. Sci. Technol. 2007, 41 (19), 6711–6717.
(39)
Cai, N.; Peak, D.; Larese-Casanova, P. Factors influencing natural organic matter sorption onto commercial graphene oxides. Chem. Eng. J. 2015, 273 (5),
ACS Paragon Plus Environment
Environmental Science & Technology
568–579. (40)
Rashidi, N. A.; Yusup, S. Overview on the Potential of Coal-Based Bottom Ash as Low-Cost Adsorbents. ACS Sustain. Chem. Eng. 2016, 4 (4), 1870–1884.
(41)
Kołodziej, A.; Fuentes, M.; Baigorri, R.; Lorenc-Grabowska, E.; García-Mina, J. M.; Burg, P.; Gryglewicz, G. Mechanism of adsorption of different humic acid fractions on mesoporous activated carbons with basic surface characteristics. Adsorption 2014, 20 (5), 667–675.
(42)
Lou, L.; Liu, F.; Yue, Q.; Chen, F.; Yang, Q.; Hu, B.; Chen, Y. Influence of humic acid on the sorption of pentachlorophenol by aged sediment amended with rice-straw biochar. Appl. geochemistry 2013, 33, 76–83.
(43)
Tang, W. W.; Zeng, G. M.; Gong, J.-L.; Liang, J.; Xu, P.; Zhang, C.; Huang, B. B. Impact of humic/fulvic acid on the removal of heavy metals from aqueous solutions using nanomaterials: a review. Sci. Total Environ. 2014, 468, 1014–1027.
(44)
Newcombe, G.; Morrison, J.; Hepplewhite, C.; Knappe, D. R. U. Simultaneous adsorption of MIB and NOM onto activated carbon: II. Competitive effects.
Carbon 2002, 40 (12), 2147–2156. (45)
Pelekani, C.; Snoeyink, V. L. A kinetic and equilibrium study of competitive adsorption between atrazine and Congo red dye on activated carbon: the importance of pore size distribution. Carbon 2001, 39 (1), 25–37.
(46)
Newcombe, G.; Morrison, J.; Hepplewhite, C. Simultaneous adsorption of MIB and NOM onto activated carbon. I. Characterisation of the system and NOM adsorption. Carbon 2002, 40 (12), 2147–2156.
(47)
Zhang, S.; Shao, T.; Bekaroglu, S. S. K.; Karanfil, T. The impacts of aggregation and surface chemistry of carbon nanotubes on the adsorption of synthetic organic compounds. Environ. Sci. Technol. 2009, 43 (15), 5719–5725.
(48)
Mendoza, E.; Rodriguez, J.; Li, Y.; Zhu, Y. Q.; Poa, C. H. P.; Henley, S. J.; Romano-Rodriguez, A.; Morante, J. R.; Silva, S. R. P. Effect of the
ACS Paragon Plus Environment
Page 24 of 29
Page 25 of 29
Environmental Science & Technology
nanostructure and surface chemistry on the gas adsorption properties of macroscopic multiwalled carbon nanotube ropes. Carbon 2007, 45 (1), 83–88.
ACS Paragon Plus Environment
Environmental Science & Technology
Fig. 1. Adsorption isotherms in ultrapure water (A) E2 mass basis, (B) EE2 mass basis, (C) E2 SSA normalized, (D) EE2 SSA normalized, (E) E2 oxygen content normalized, and (F) EE2 oxygen content normalized.
ACS Paragon Plus Environment
Page 26 of 29
Page 27 of 29
Environmental Science & Technology
Fig. 2. Adsorption isotherms in NOM solution (A) E2 mass basis, (B) EE2 mass basis.
ACS Paragon Plus Environment
Environmental Science & Technology
Page 28 of 29
Table 1. Selected physiochemical properties of all adsorbents. Adsorbent
rGO1 rGO2 MWCNT SWCNT BC1 BC2 PAC GAC
*
SSA m2/g
PV** cm3/g
244 167 175 557 85 142 1255 1354
0.155 0.109 0.664 1.043 0.057 0.185 0.757 0.778
DFT pore volume distribution*** Vmicro (50 nm) %
25.1 18.8 7.0 16.1 13.4 11.5 37.0 42.6
69.2 73.9 65.4 77.8 75.7 69.8 61.9 56.4
4.7 7.3 27.6 6.1 10.9 18.7 1.1 1.0
ACS Paragon Plus Environment
Oxygen content %
pHpzc Pristine
NOM preloading
16.69 10.33 2.99 4.94 24.27 21.95 28.01 21.92
4.8 5.6 7.5 6.7 3.3 4.1 3.2 4.1
4.5 4.3 5.5 4.5 3.1 3.8 2.8 3.5
Page 29 of 29
Environmental Science & Technology
Table 2. Freundlich isotherm parameters of estrogens adsorption in ultrapure water and NOM solution. Adsorbent
rGO1 rGO2 MWCNT SWCNT BC1 BC2 PAC GAC
KF (mg/g)/(mg/L)N E2 EE2 64.39 77.86 43.54 103.81 6.56 9.19 132.73 29.30
38.68 61.41 22.68 74.66 1.52 2.85 114.05 12.21
KF-SSA (mg/m2)/(mg/L)N E2 EE2 0.26 0.47 0.25 0.19 0.08 0.06 0.11 0.02
0.16 0.37 0.13 0.13 0.02 0.02 0.09 0.01
KF-NOM (mg/m2)/(mg/L)N E2 EE2 44.36 43.76 16.33 47.75 2.60 3.84 58.66 9.70
23.39 33.94 9.93 29.68 0.72 1.27 49.59 5.18
RSSA (‰)
RNOM (%)
E2
EE2
E2
EE2
4.0 6.0 5.7 1.8 12.2 6.5 0.8 0.7
4.1 6.0 5.7 1.7 13.2 7.0 0.8 0.7
68.9 56.2 37.5 46.0 39.6 41.8 44.2 33.1
60.5 55.3 43.8 39.8 47.4 44.6 43.5 42.4
In ultrapure water N R2 E2 EE2 E2 EE2 0.698 0.611 0.651 0.505 0.747 0.728 0.392 0.759
ACS Paragon Plus Environment
0.524 0.698 0.690 0.476 0.844 0.851 0.326 0.496
0.9942 0.9958 0.9943 0.9991 0.9796 0.9971 0.9938 0.9795
0.9956 0.9965 0.9691 0.9935 0.9980 0.9939 0.9679 0.9501
In NOM solution N R2 E2 EE2 E2 EE2 0.889 0.836 0.795 0.601 0.895 0.776 0.522 0.762
0.656 0.782 0.778 0.670 0.910 0.993 0.469 0.590
0.9982 0.9975 0.9983 0.9973 0.9728 0.9986 0.9967 0.9882
0.9855 0.9951 0.9919 0.9973 0.9872 0.9918 0.9873 0.9797