Automated Large-Scale Synthesis of ... - ACS Publications

Oct 3, 2007 - Stefan Hilf , Johannes Klos , Kookheon Char , Heeje Woo , Andreas F. M. Kilbinger. Macromolecular Rapid Communications 2009 30 (14), ...
0 downloads 0 Views 348KB Size
Macromolecules 2007, 40, 7827-7833

7827

Automated Large-Scale Synthesis of Supramolecular Oligo(p-benzamide) Block Copolymers Johannes Klos, Frederik Wurm, Hannah M. Ko1 nig, and Andreas F. M. Kilbinger* Institute of Organic Chemistry, Johannes Gutenberg-UniVersita¨t Mainz, Duesbergweg 10-14, 55099 Mainz, Germany ReceiVed May 8, 2007; ReVised Manuscript ReceiVed July 25, 2007

ABSTRACT: A fully automated large-scale synthesis procedure has been developed that allows the preparation of supramolecular rod-coil copolymers on a 100 g scale. The new reaction cycle allows the stepwise growth of oligo(p-benzamide)s onto the chain end of amine-terminated polymers. Amine-terminated poly(ethylene glycol) (PEG, Mn ) 5000 g mol-1) and poly(styrene) (PS, Mn ) 2950 g mol-1) were prepared, and an octa(p-benzamide) oligomer block was grown from the chain end in an automated computer-controlled reaction cycle. Plotting the apparent molecular weight of the PEG copolymer against the number of reaction cycles revealed a linear relationship, which emphasized the high level of control this method offers. The block copolymers show strong aggregation in nonpolar solvents such as chloroform. Remarkably, transmission electron microscopy images of drop-cast chloroform solutions show perfectly uniform rodlike micelles for the PEG and the PS copolymer.

Introduction Rod-coil copolymers in which the rod block consists of a strongly aggregating oligomer that drives the self-assembly process have received significant attention over the past decade.1 Because of the small dimensions of the oligomeric rod block, solution or solid state structures can be obtained with such systems on length scales much smaller than typically obtainable by coil-coil copolymers.2 Most examples of oligomeric rodcoil copolymers described so far rely on nonspecific π-interactions to obtain higher degrees of order in solution or the solid state. In a few examples, however, directional hydrogen bonds are exploited to induce order into the block copolymer. β-sheetforming oligopeptides have, for example, been attached to coiltype polymers by several groups.3-7 The peptide motif dominated the superstructure formation as long sheets of oligomers; i.e., rodlike micelles were observed in solution. Our group has been investigating copolymers of the β-sheet mimicking oligo(p-benzamide) (OPBA). We have developed several synthetic routes in solution as well as on solid support and described the aggregation phenomena in detail.8-13 All of the above-mentioned block copolymers consist of a precisely defined oligomeric block that was synthesized on solid support or using standard organic synthesis procedures often involving laborious protection chemistry. Therefore, the amounts of product available for these very precisely defined materials are typically limited to the multi-milligram regime. In recent years, many groups have synthesized ever more complex and precisely defined polymeric materials using the tools of classical organic chemistry.14 While this approach provides a high level of structural confidence, multistep organic syntheses can severely hamper the preparation of larger quantities of materials. In order to be able to evaluate materials properties especially in the bulk, synthetic routes are required that give access to the 10-100 g scale without the need for laborious multistep syntheses and wasteful purification procedures. We therefore devised a new synthetic procedure that is fully automated, can be run on the 100 g scale, yet produces * Corresponding author. E-mail: [email protected].

surprisingly well-defined supramolecular OPBA rod-coil copolymers. Here we report the proof of concept using two different types of coil polymers (PS and PEG) onto which we condensed octa(p-benzamide)s in an automated computer-controlled fashion. Experimental Section Instrumentation. 1H and 13C nuclear magnetic resonance spectra (NMR) were recorded at a frequency of 300 MHz on a Bruker AC 300 or on a Bruker AMX 400 working at 400 and 100 MHz, respectively, for 13C (on the Bruker AMX 400), using benzenze-d6 as solvent. 29Si NMR spectra were recorded on a Bruker AMX 400 at 79.49 MHz which was referenced externally to TMS. Size exclusion chromatography in tetrahydrofuran (THF) or chloroform was performed on an instrument consisting of a Waters 717 plus autosampler, a TSP Spectra Series P 100 pump, and a set of three PSS-SDV 5 µm columns with 100, 1.000, and 10.000 Å porosity. Calibration was carried out using poly(styrene) standards provided by Polymer Standards Service and performing a third-order polynomial fit. The eluent was used at 30 °C and at a flow rate of 1 mL min-1. UV absorption was detected by a SpectraSYSTEM UV2000. The specific refractive index increment (dn/dc) was measured at 30 °C on an Optilab DSP interferometric refractometer (also RI detector). For measurements in dimethylformamide (DMF) containing 1 g L-1 of lithium bromide, an Agilent 1100 Series GPCSetup (gel permeation chromatography) was used as an integrated instrument including a PSS HEMA column (106/105/104 g mol-1), a UV (254 nm), and RI detector. Calibration was carried out using polystyrene standards provided by Polymer Standards Service. The eluent was used at 50 °C and at a flow rate of 1 mL min-1. Field desorption mass spectra were measured on a Finnigan MAT 95. A Philips EM 420 transmission electron microscope using a LaB6 cathode at an acceleration voltage of 120 kV was used to obtain TEM images. TEM grids (carbon film on copper, 300 mesh) were obtained from Electron Microscopy Sciences, Hatfield, PA. UV/ vis spectra were measured on a Perkin-Elmer Lambda 2. Materials. Cyclohexane (Acros, p.A.) and tetrahydrofuran (THF) (Acros, p.A.) for polymerizations were purified by cryo-transfer from a dark-red living polystyrene (PS, 99%), solution just prior to use. Styrene (Acros) was stored over CaH2 (Fluka, 99%) until used. Allylamine (Acros, 99%) was used as received. sec-Butyllithium (1.6 M, Acros) was used as received. The concentration of the initiator was determined by the Gilman double titration

10.1021/ma0710378 CCC: $37.00 © 2007 American Chemical Society Published on Web 10/03/2007

7828

Klos et al.

method.15 Chlorodimethylsilane (Acros, 99%) was dried over CaH2 and cryo-transferred into an ampule until used. CaH2 was purchased from Fluka and used as received. Toluene (extra dry, with molecular sieves, water