BERNARD JURALE

tory work on "unknowns." Many former students now. 5. Sulfide test group: Cd++, Sb+++, Pb++, As+++. taking college chemistry have said that it was the...
0 downloads 0 Views 1MB Size
BERNARD JURALE Meriden High School, Meriden, Connecticut

THE

most enjoyable and valuable unit in the Meriden High School chemistry course is the two weeks of lahoratory work on "unknowns." Many former students now taking college chemistry have said that it was the work that helped them the most in their firsbyear course. This unit does not attempt to prepare for or to imitate the procedure of conventional qualitative analysis. The imnortant obiective is to teach facts and nrinci~les that are essential for the understanding of chemistry. It also offers an opportunity to teach laboratory techniques and to use facts determined experimentally. Laboratory work that does not give the student opportunity to base his next steps on the facts that he has already determined cannot be considered the best type of learning by doing. Tests for the various ions are sometimes made by the "hibor-miss" method. This lack of methodical procedure is wasteful of chemicals and time. Every test should be made with the thought of what has to be determined. The method of testing described here is an attempt to unify the accepted test procedures of highschool chemistry into a workable laboratory exercise. We prefer to omit some laboratory work of doubtful value on the metals and to substitute a long period for topics that do not lend themselves to ordinary classroom procedures. We find that good laboratory techniques and use of the scientific method may be inculcated by a longer laboratory unit better than by an equal time spread out in weekly laboratory periods. Also, the work on the "unknowns" is an excellent opportunity to apply such topics as hydrolysis, electromotive series, solubility rules, and ionic reactions. Hydrolysis is sometimes given inadequate consideration in high-school chemistry. This may be due to the lack of examples to show that hydrolysis plays an important part in chemical reactions involving ions. It is, however, a valuable asset in determining the relative behavior of the ions in a salt. Universal indicator paper gives a much better check on pH value of a salt solution than does litmus. The preliminary work consists of reviewing the important ions and their identification. These tests have either been taken up previously in laboratory work or shown as demonstrations in the classroom. In order to coordinate the procedure the cations are classified according to method of testing and the anions by the strength of the related acids. Also, each student is assigned to a sample that is within his ability to identify. The cation groups are as follows: 1. Ammonium ion. 2. Alkali metals: Li+, K+, Na+.

3. Alkaline earths: Ba++, Sr++, Ca++. Cobalt nitrate test group: Mg++, Al+++, Zn++. 5. Sulfide test group: Cd++, Sb+++, Pb++, As+++. 6. Borax-bead test group: Mn++, Cr+++, Co++, Ni++, Fe++, Fe+++. 7. Replacement group: Cu++, Ag+, Pb++. -

4.

The anions are divided into three groups: 1. Strong acid ions: Sod--, NOS-, C1-. 2. Moderate acid ions: Br-, I-, CH,COO-. 3. Weak acid ions: SOS--, S--, GOS--. PROCEDURE

Obtain a 1-g. sample of a simple salt or an alum from the instructor. (1) Record the color, appearance, and the form of the crystal if it is crystalline. Find out by a test whether or not it contains water of crystallization. (2) Dissolve one-half of the sample in 25 ml. of distilled water. Test the solution with universal indicator paper and with litmus. Record the hydrolysis as A (strongly acid), a (weakly acid), N (neutral), b (weakly alkaline), B (strongly alkaline). If the solution is not clear, determine whether the precipitate is caused by hydrolysis or by insolubility. In the former case, in what group would you expect to find the metal? (3) Take a 3-ml. sample of the solution. Add sodium hydroxide solution carefully, a drop a t a time, shaking after each addition. Record the appearance, color, and type of the precipitate, if any. If no precipitate, test for ammonium ion by warming and noticing the odor or the effecton moist red litmus held above the liquid in the tube. (4) From the results of the hydrolysis test and from the color, type, or lack of precipitate, determine to what group the metallic ion is likely to belong. (a) (b) (c) (d)

(e)

Precipitate None White cloudy White gelatinous White heavy curd Colored

Ions NH4+, Li+, K+, Na+ Ca++, Sr++, Ba++ Mg++, Al+++, Zn++ Cd++, Sb+++,Pb++ Ag+, Fe++, Fe+++, Mn++, Cr+++, Co++, Ni++, Cu++

(5) Group (a). Ammonium ion test given. Flame test for other three. Group (b). Flame tests. Check Ca++ by lack of a precipitate when Calgon (sodium hexametaphosphate) solution is added before ammonium oxalate solution, and the

FEBRUARY, 1951

presence of a precipitate with ammonium oxalate solution in the absence of Calgon. Or, to distinguish between Ca++ and Ba++ if the flame test is not conclusive, acidify the sample of salt t o be tested with dilute nitric acid. Add, a drop at a time, a solution of dilute sulfuric acid. A precipitate will be formed by the addition of one drop of the acid if the salt contains Ba++ ions. Calcium salt will require much more acid to obtain a precipitate. Group (c). Apply cobalt nitrate test. Group (d). Add hydrogen sulfide solution or ammonium sulfide and observe color of precipitate. Group ( e ) . Mn++, Cr+++, Co++, Ni++ are identified by the borax bead test. Fe+++ gives a red color with KCSN solution. Alternatively, a blue color is obtained with ICFe(CN)o solution. Fe++ is identified by a blue precipitate with K3Fe(CN)6 solution. Cu++ mill be replaced as a red metal by an iron nail, and Ag+ is replaced by a copper wire forming a black or a silvery deposit.

103

Flame tests can be made without the use of platinum mire. Ignite a splint and produce a carbonized section by putting out the flame with water. A small amount of salt mill adhere to the charcoal. The flame test is made without interference from wood gases. The borax bead test can also he made without platinum. Heat the end of a glass rod about 2 mm. in diameter. Thrust into powdered borax and reheat. Repeat until a drop of melted borax adheres t o the rod. Pick up a small amount of sample and heat. Rotate the rod in the flame and the sample will mix evenly with borax. These beads may be saved for reference and comparison. (6) When the cation has been identified, use the result of the hydrolysis test for an indication of the group to which the anion belongs. Make appropriate tests to identify the anion. (7) Write equations for all the reactions used in identifying your compound and point out clearly the steps you used t o reach the identification. ACKNOWLEDGMENT

The writer wishes to acknowledge his indebtedness to Elhert Weaver for his help in revising this paper.