Charge Percolation Pathways Guided by Defects in Quantum Dot Solids

Apr 6, 2015 - Applied Science and Technology Graduate Program, University of California at Berkeley, Berkeley, California 94720, United States. ‡. M...
0 downloads 9 Views 2MB Size
Letter pubs.acs.org/NanoLett

Charge Percolation Pathways Guided by Defects in Quantum Dot Solids Yingjie Zhang,†,‡ Danylo Zherebetskyy,‡ Noah D. Bronstein,§ Sara Barja,‡ Leonid Lichtenstein,‡ David Schuppisser,‡ Lin-Wang Wang,‡ A. Paul Alivisatos,‡,§,∥,⊥ and Miquel Salmeron*,‡,∥ †

Applied Science and Technology Graduate Program, University of California at Berkeley, Berkeley, California 94720, United States Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, California 94720, United States § Department of Chemistry, University of California at Berkeley, Berkeley, California 94720, United States ∥ Department of Materials Science and Engineering, University of California at Berkeley, Berkeley, California 94720, United States ⊥ Kavli Energy NanoScience Institute, Berkeley, California 94720, United States ‡

S Supporting Information *

ABSTRACT: Charge hopping and percolation in quantum dot (QD) solids has been widely studied, but the microscopic nature of the percolation process is not understood or determined. Here we present the first imaging of the charge percolation pathways in two-dimensional PbS QD arrays using Kelvin probe force microscopy (KPFM). We show that under dark conditions electrons percolate via in-gap states (IGS) instead of the conduction band, while holes percolate via valence band states. This novel transport behavior is explained by the electronic structure and energy level alignment of the individual QDs, which was measured by scanning tunneling spectroscopy (STS). Chemical treatments with hydrazine can remove the IGS, resulting in an intrinsic defect-free semiconductor, as revealed by STS and surface potential spectroscopy. The control over IGS can guide the design of novel electronic devices with impurity conduction, and photodiodes with controlled doping. KEYWORDS: Quantum dot, charge transport, charge percolation, defect, in-gap states, Kelvin probe force microscopy

A

potential energy landscapes, which are determined by the microscopic disorder, the energy level alignment of individual sites, and the strength of coupling between adjacent sites. When charges are injected, they will fill the potential valleys, forming percolation pathways.22 As a model system, quantum dot solids offer a unique opportunity for local characterization of the individual building blocks, whose properties can be correlated with the mesoscale percolation and ensemble transport phenomena. Here we combined scanning tunneling microscopy (STM), Kelvin probe force microscopy (KPFM), and field effect transistor (FET) techniques to characterize the states responsible for charge percolation in QD solids both microscopically and spectroscopically. We found a phenomenon where in-gap states (IGS) induce Fermi level pinning favoring electron transport via the conductive IGS, forming percolation pathways. Both the technical methodology and the determined transport mechanism can be generally applicable to other disordered semiconductors.

n important goal in the design of modern materials is to create new forms of matter by combining elementary nanoscale building blocks.1−9 One example is the artificial solids formed by placing quantum dots in arrays.4−9 By controlling the band gap of the individual dots through their size, and the degree to which charges move from one dot to the next through controlled barriers, we can design and tune the transport properties of quantum dot solids. Potential applications include solution-processed field effect transistors, solar cells, photodetectors, etc.4−9 The individual QDs are themselves complex, tiny solids, comprised of hundreds to thousands of atoms. Inevitably the fabrication of these constituents is imperfect; consequently, the QDs are not identical in the number and arrangement of atoms. In addition, defects and impurities are also present that can play an important role.10−13 Therefore, it is not surprising that the microscopic mechanisms of charge hopping in QD arrays have not yet been determined.7,8,13−17 Understanding the transport mechanism is also relevant to a broader class of disordered semiconductors,18 which are systems with spatial disorder and/or heterogeneity in the electronic states. Examples include amorphous silicon,19 heavily doped and highly compensated semiconductors,20 and organic semiconductors.21 These systems exhibit spatially varying © XXXX American Chemical Society

Received: February 3, 2015 Revised: April 1, 2015

A

DOI: 10.1021/acs.nanolett.5b00454 Nano Lett. XXXX, XXX, XXX−XXX

Letter

Nano Letters Direct Imaging of Charge Transport in PbS Quantum Dots. We chose PbS QDs as the artificial atoms from which to form artificial solids, in the form of thin films consisting of 0−2 QD layers. These QDs show strong quantum confinement due to the large Bohr radius,23 so that the wave function of one dot can extend into neighboring dots, giving rise to an electrically active QD solid. As-synthesized PbS QDs (5.5 nm diameter, ∼0.9 eV band gap, Supporting Information) are capped with insulating oleate ligands24 that can be exchanged with shorter ligands, such as 1,2-ethanedithiol (EDT), 3-mercaptopropionic acid (MPA), iodide, etc., to couple the QDs and enhance conduction.5,6,12−15 To resolve the spatial and energetic pathways of electron and hole transport, we used KPFM25,26 to quantitatively image the local surface potential (Vsf) distribution in a QD film deposited in the channel region of a field effect transistor (FET) (Figure 1A). All KPFM and FET measurements were done under dark

along the percolation pathways will be pinned by the energy levels responsible for charge transport. The areas with no conductive states at the corresponding energy will exhibit higher (for electrons) or lower (for holes) surface potential due to gate field penetration. The topographic image shows the distribution of individual PbS-EDT QDs in a channel area (Figure 1B), while the surface potential images of the same area (Figure 1C, D) reveal the transport pathway structures. The electron percolation pathways, shown by the cyan/blue areas in Figure 1C (where the injected electrons reside), are in the form of narrow stripes surrounded by electron-insulating areas (red/ white). In contrast, the hole percolation pathways, shown by the white/red areas in Figure 1D (where the injected holes reside), form larger domains surrounded by hole-insulating areas (blue/cyan). The hole transporting level is located at ∼−5.0 eV (below vacuum level), matching the valence band edge position of the QDs.27 However, the level responsible for electron transport is located at ∼−4.8 eV, far below the conduction band edge (∼−4.1 eV). The presence of electronconducting IGS at ∼−4.8 eV is an unexpected finding. In-Gap States and Charge Percolation Mechanism. To better understand the percolation phenomena, we measured the electronic structure of individual QDs using STM and scanning tunneling spectroscopy (STS) (Figure 2A, B).

Figure 1. Imaging charge percolation pathways in QD solids. (A) Schematic diagram of a QD thin film FET and KPFM probe setup. Au electrodes serve as the source and drain. The FET channel length is 20 μm, and its width is 1 mm. A monolayer of OTS (green) was preadsorbed on the SiO2 surface of the channel to passivate the oxide surface trap states. (B to D) KPFM images of the same region in the channel area of a PbS-EDT QD array FET. Scale bar: 50 nm. (B) Topography showing 0−2 layers of QD, (C and D) surface potential maps at Vg = 52 V and Vg = −52 V, respectively. Source and drain electrodes were grounded during measurements. The color scales of the surface potential images are saturated to enhance contrast. The same images with nearly the full scales show the same percolation pathway structures (Supporting Information).

Figure 2. Electronic structure of individual PbS-EDT quantum dots. (A) Schematic diagram of STM and STS measurements of QDs deposited on an ITO substrate. (B) STM image with individually resolved PbS-EDT QDs. (C) STS curves of individual PbS-EDT QDs. The sample bias corresponds to the energy level position with respect to Fermi level. Three types of spectra are found, labeled according to the existence of in-gap states (IGS) and to 1Sh level alignment.

Measurements were done at 77 K in ultrahigh vacuum (base pressure μh for the 2-D PbS-EDT arrays studied here. From comparison of PbS-HYD and PbS-EDT QDs, the former have a much higher surface coverage (95% vs 59%, as determined from AFM images), and a larger β due to the smaller interparticle distance (since the PbS-HYD QD surface is almost bare, as revealed by infrared absorption measurements). These two factors are responsible for the larger measured μe and μh of PbS-HYD compared to those of PbS-EDT. The submonolayer coverage is responsible for the much smaller source−drain current compared to that of thin films (typically ∼50 nm thick). Discussion and Conclusion. There has been many postulations regarding the atomic origin of IGS in lead chalcogenide QDs, including incomplete ligand passivation,31 nonstoichiometry,32,33 and surface oxidation.34−36 Here we found that hydrazine, a strong reducing agent, can efficiently remove IGS. Our results thus indicate that oxygen-related species are likely at the origin of the conductive IGS, although we cannot rule out other possibilities. We also note that there may exist shallow trap states within the thermal energy from the valence/conduction band edge, which cannot be distinguished from the 1Sh/1Se states due to the resolution limit of the STM and KPFM. The phenomenon of ambipolar transport with larger electron mobility has also been reported for PbSe QD thin films treated with EDT.15,36 Therefore, we expect the mechanism of electron transport through IGS to be generally applicable to lead chalcogenide QD solids with EDT treatments under dark conditions in an FET geometry. One promising application of QD solids is in large area, flexible electronics, such as transistors, circuits, memory, and sensors.37 These devices can be fabricated by room temperature, roll-to-roll solution processing, which reduces cost. However, the fabricated QD films are more prone to defects and impurities compared to traditional high-temperature, vacuum processed crystalline semiconductors. In contrast to the traditional view that defects act simply as traps hindering carrier transport, this work shows the beneficial role of impurities, which can thus serve as the starting point for engineering conductive impurities that can be controlled during solution processing. The mechanism of in-gap state induced Fermi level pinning and favorable charge percolation via IGS is likely to be relevant to other QD and organic semiconductor systems as well. On the other hand, for QD based optoelectronic devices in diode geometries, the goal is to harness the photoexcited charge carriers that are transported via conduction/valence band states. In contrast to the (quasi-)equilibrium process of electrostatic field-controlled charge injection and transport in the linear regime in the FETs, photocarrier transport in diodes are inherently a nonequilibrium process that requires constant



ASSOCIATED CONTENT

S Supporting Information *

Nanocrystal synthesis and film preparation, FET preparation, KPFM measurements, KPFM images of PbS-EDT in full scale, KPFM images of PbS-HYD, normalized STS curve of PbSHYD, contact resistance analysis. This material is available free of charge via the Internet at http://pubs.acs.org.



AUTHOR INFORMATION

Corresponding Author

*E-mail: [email protected]. Notes

The authors declare no competing financial interest.



ACKNOWLEDGMENTS The authors thank Q. Chen for discussion of the manuscript. We also thank J. M. Lucas for nanocrystal synthesis and A. Pun for OTS deposition. We thank E. H. Sargent for discussion on photovoltaic applications. This work was supported by the “Self-Assembly of Organic/Inorganic Nanocomposite Materials” program, Office of Science, the Office of Basic Energy Sciences (BES), Materials Sciences and Engineering (MSE) Division of the U.S. Department of Energy (DOE) under Contract No. DE-AC02-05CH11231. It used resources of the Molecular Foundry, a DOE Office of Science user facility. S.B. acknowledges fellowship support by the European Union under FP7-PEOPLE-2012-IOF-327581. L.L. acknowledges support from the Alexander van Humboldt Foundation.



REFERENCES

(1) Huynh, W. U.; Dittmer, J. J.; Alivisatos, A. P. Science 2002, 295, 2425−2427. (2) Cui, Y.; Lieber, C. M. Science 2001, 291, 851−853. (3) Tessler, N.; Medvedev, V.; Kazes, M.; Kan, S.; Banin, U. Science 2002, 295, 1506−1508. (4) Graetzel, M.; Janssen, R. A. J.; Mitzi, D. B.; Sargent, E. H. Nature 2012, 488, 304−312. (5) Chuang, C. M.; Brown, P. R.; Bulović, V.; Bawendi, M. G. Nat. Mater. 2014, 13, 786−801. (6) Ning, Z.; Voznyy, O.; Pan, J.; Hoogland, S.; Adinolfi, V.; Xu, J.; Li, M.; Kirmani, A. R.; Sun, J.-P.; Minor, J.; Kemp, K. W.; Dong, H.; Rollny, L.; Labelle, A.; Carey, G.; Sutherland, B.; Hill, I.; Amassian, A.; Liu, H.; Tang, J.; Bakr, O. M.; Sargent, E. H. Nat. Mater. 2014, 13, 822−828. (7) Talapin, D. V.; Murray, C. B. Science 2005, 310, 86−89. D

DOI: 10.1021/acs.nanolett.5b00454 Nano Lett. XXXX, XXX, XXX−XXX

Letter

Nano Letters (8) Lee, J.; Kovalenko, M. V.; Huang, J.; Chung, D. S.; Talapin, D. V. Nat. Nanotechnol. 2011, 6, 348−352. (9) Clifford, J. P.; Konstantatos, G.; Johnston, K. W.; Hoogland, S.; Levina, L.; Sargent, E. H. Nat. Nanotechnol. 2009, 4, 40−44. (10) Wolkin, M. V.; Jorne, J.; Fauchet, P. M.; Allan, G.; Delerue, C. Phys. Rev. Lett. 1999, 82, 197−200. (11) Cordones, A. A.; Scheele, M.; Alivisatos, A. P.; Leone, S. R. J. Am. Chem. Soc. 2012, 134, 18366−18373. (12) Diaconescu, B.; Padilha, L. A.; Nagpal, P.; Swartzentruber, B. S.; Klimov, V. I. Phys. Rev. Lett. 2013, 110, 127406. (13) Nagpal, P.; Klimov, V. I. Nat. Commun. 2011, 2, 486. (14) Jeong, K. S.; Tang, J.; Liu, H.; Kim, J.; Schaefer, A. W.; Kemp, K.; Levina, L.; Wang, X. H.; Hoogland, S.; Debnath, R.; Brzozowski, L.; Sargent, E. H.; Asbury, J. B. ACS Nano 2012, 6, 89−99. (15) Liu, Y.; Gibbs, M.; Puthussery, J.; Gaik, S.; Ihly, R.; Hillhouse, H. W.; Law, M. Nano Lett. 2010, 10, 1960−1969. (16) Bozyigit, D.; Volk, S.; Yarema, O.; Wood, V. Nano Lett. 2013, 13, 5284−5288. (17) Drndić, M.; Markov, R.; Jarosz, M. V.; Bawendi, M. G.; Kastner, M. A.; Markovic, N.; Tinkham, M. Appl. Phys. Lett. 2003, 83, 4008− 4010. (18) Anderson, P. W. Phys. Rev. 1958, 109, 1492−1605. (19) Le Comber, P. G.; Spear, W. E. Phys. Rev. Lett. 1970, 25, 509− 511. (20) Mott, N. F.; Twose, W. D. Adv. Phys. 1961, 10, 107−163. (21) Coropceanu, V.; Cornil, J.; da Silva, D. A.; Olivier, Y.; Silbey, R.; Bredas, J. L. Chem. Rev. 2007, 107, 926−952. (22) Elliott, R. J.; Krumhansl, J. A.; Leath, P. L. Rev. Mod. Phys. 1974, 46, 465−543. (23) Kang, I.; Wise, F. W. J. Opt. Soc. Am. B 1997, 14, 1632−1646. (24) Zherebetskyy, D.; Scheele, M.; Zhang, Y.; Bronstein, N.; Thompson, C.; Britt, D.; Salmeron, M.; Alivisatos, P.; Wang, L.-W. Science 2014, 344, 1380−1384. (25) Zhang, Y.; Ziegler, D.; Salmeron, M. ACS Nano 2013, 7, 8258− 8265. (26) Zhang, Y.; Pluchery, O.; Caillard, L.; Lamic-Humblot, A.-F.; Casale, S.; Chabal, Y. J.; Salmeron, M. Nano Lett. 2015, 15, 51−55. (27) Jasieniak, J.; Califano, M.; Watkins, S. E. ACS Nano 2011, 5, 5888−5902. (28) Kirkpatrick, S. Rev. Mod. Phys. 1973, 45, 574−588. (29) Sze, S. M. Physics of Semiconductor Devices, 2nd ed.; Wiley: New York, 1981. (30) Remacle, F.; Levine, R. D. ChemPhysChem 2001, 2, 20−36. (31) Ip, A. H.; Thon, S. M.; Hoogland, S.; Voznyy, O.; Zhitomirsky, D.; Debnath, R.; Levina, L.; Rollny, L. R.; Carey, G. H.; Fischer, A.; Kemp, K. W.; Kramer, I. J.; Ning, Z. J.; Labelle, A. J.; Chou, K. W.; Amassian, A.; Sargent, E. H. Nat. Nanotechnol. 2012, 7, 577−582. (32) Kim, D.; Kim, D.-H.; Lee, J.-H.; Grossman, J. C. Phys. Rev. Lett. 2013, 110, 196802. (33) Oh, S. J.; Berry, N. E.; Choi, J.-H.; Gaulding, E. A.; Paik, T.; Hong, S.-H.; Murray, C. B.; Kagan, C. R. ACS Nano 2013, 7, 2413− 2421. (34) Leschkies, K. S.; Kang, M. S.; Aydil, E. S.; Norris, D. J. J. Phys. Chem. C 2010, 114, 9988−9996. (35) Zarghami, M. H.; Liu, Y.; Gibbs, M.; Gebremichael, E.; Webster, C.; Law, M. ACS Nano 2010, 4, 2475−2485. (36) Luther, J. M.; Law, M.; Song, Q.; Perkins, C. L.; Beard, M. C.; Nozik, A. J. ACS Nano 2008, 2, 271−280. (37) Kim, D. K.; Lai, Y.; Diroll, B. T.; Murray, C. B.; Kagan, C. R. Nat. Commun. 2012, 3, 1216. (38) Zhitomirsky, D.; Voznyy, O.; Levina, L.; Hoogland, S.; Kemp, K. W.; Ip, A. H.; Thon, S. M.; Sargent, E. H. Nat. Commun. 2014, 5, 3803. (39) Engel, J. H.; Alivisatos, A. P. Chem. Mater. 2014, 26, 153−162.

E

DOI: 10.1021/acs.nanolett.5b00454 Nano Lett. XXXX, XXX, XXX−XXX