Chiral 3D Covalent Organic Frameworks for High Performance Liquid

5 hours ago - Voltage loss in Li-ion batteries explained. Low-cost electrodes that store more lithium than the ones used in today's lithium-ion batter...
2 downloads 13 Views 832KB Size
Subscriber access provided by READING UNIV

Communication

Chiral 3D Covalent Organic Frameworks for High Performance Liquid Chromatographic Enantioseparation Xing Han, Jinjing Huang, Chen Yuan, Yan Liu, and Yong Cui J. Am. Chem. Soc., Just Accepted Manuscript • DOI: 10.1021/jacs.7b12110 • Publication Date (Web): 05 Jan 2018 Downloaded from http://pubs.acs.org on January 5, 2018

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Journal of the American Chemical Society is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Journal of the American Chemical Society

Chiral 3D Covalent Organic Frameworks for High Performance Liquid Chromatographic Enantioseparation Xing Han, Jinjing Huang, Chen Yuan, Yan Liu,* and Yong Cui* School of Chemistry and Chemical Engineering and State Key Laboratory of Metal Matrix Composites, Shanghai Jiao Tong University, Shanghai 200240, China Supporting Information ABSTRACT: In spite of their great promise for enantioselective processes due to the rich host-guest chemistry, it remains a formidable challenge to construct covalent organic frameworks (COFs) with chiral three-dimensional (3D) structures. Here we report the bottom-up synthesis of the first example of 3D chiral COFs by imine condensation of an enantiopure twofold symmetric TADDOL-derived tetraaldehyde with a tetrahedral tetra(4-anilyl)methane. After post-synthetic oxidation of imine linkages, the framework is transformed into an amide-linked COF with retention of crystallinity and permanent porosity as well as enhanced chemical stability. The resultant two isostructural COFs feature a four-fold interpenetrated diamondoid open framework with tubular channels decorated with chiral dihydroxy auxiliaries. Both COFs can be used as chiral stationary phases for high performance liquid chromatography to enantioseparate racemic alcohols, and what is more, the oxidized COF shows superior separation performance compared to the pristine framework.

Covalent organic frameworks (COFs) have recently emerged as a new class of crystalline porous materials by integrating organic building blocks into predetermined network structures through covalent bonds.1-3 Given their high porosity with functionalized internal surface and ability to tune structural and physical parameters, COFs have shown great promise for a variety of applications such as molecule storage and separation,4,5 optoelectronics,6 energy storage,7 drug delivery,8 sensing9 and catalysis.10,11 It has become fairly prevalent to construct twodimensional (2D) COFs, which rely on van der Waals and other non-covalent interactions in addition to covalent interactions to form layered stacking structure. Nonetheless, it remains a challenge to design and synthesize three-dimensional (3D) COFs by organizing building blocks that rely only on covalent bonds.12 From a supramolecular point of view, 3D COFs warrant exploration owing to their large surface areas, high density of open sites, and fascinating confinement effects.13 In this work, we report a bottom-up strategy for the construction of a rare 3D chiral COF (CCOF) by co-condensation of a tetrahedral tetra(4anilyl)methane (TAM) with a tetraaldehyde derived from the privileged chiral Tetraaryl-1,3-dioxolane-4,5-dimethanols (TADDOL) backbone.11a Oxidation of imine linkages of the resultant CCOF14 affords an amide-linked framework, which retains crystallinity and permanent porosity as well as exhibits enhanced chemical stability (Scheme 1). Despite their potential utilization in asymmetric catalysis, enantiopure separation and chiral optics,12 crystalline chiral porous solids based on COF networks are still quite rare. This can be presumably attributed to the synthetic challenge of

simultaneously achieving the balance and conflict of asymmetry and crystallinity. Taking advantage of the mild conditions that are typically used for COF synthesis, we and others have shown that 2D CCOFs for asymmetric catalysis could be prepared by the bottom-up assembly of judiciously selected chiral building blocks or post-modification of achiral COFs with chiral functionalities.11 However, with one exception,5a COFs have not yet been explored for chiral separation, which represents one of the most difficult preparative and analytical separations because of the identical physical and chemical properties for enantiomers. Here we report for the first time the use of CCOFs as chiral stationary phases (CSPs) for high-performance liquid chromatography (HPLC) to separate racemic alcohols, sulfoxides, carboxylic acids and esters. Scheme 1. Synthesis of the CCOFs

CCOF 5 was prepared by solvothermal reactions of enantiopure teraaldehyde TTA (0.05 mmol) and tetraamine TAM (0.05 mmol) in 1,4-dioxane (1.5 mL) in the presence of 6 M acetic acid catalyst (0.2 mL) at 120 oC for 72 h, which afforded white microcrystalline solid in ~70% yield. CCOF 6 was synthesized from 5 according to the procedure reported in literature.13 Both CCOFs 5 and 6 are not soluble in water and common organic solvents such as MeOH, DMF and THF. The COFs were characterized by a variety of spectroscopic

ACS Paragon Plus Environment

Journal of the American Chemical Society 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

techniques. The Fourier transform infrared (FT-IR) spectrum of CCOF 5 showed the disappearance of the characteristic C=O vibration band (1702 cm−1) and the appearance of the strong C=N stretching band (1627 cm-1), indicating the successful polymerization (Figure S1). For the oxidized product 6, the FT-IR spectrum showed the emergence of the characteristic C=O amide stretch at 1657 cm−1 and the disappearance of the C=N imine stretch at 1627 cm−1. It should be noted that these characteristic imine and amide stretches were corroborated by the spectra obtained for a molecular model (Figure S1).

Page 2 of 5

functionality to the amide. Circular dichroism (CD) spectra of the COFs based on the opposite enantiomers of TADDOL monomers were mirror images of each other, suggesting their enantiomeric nature (Figure S3). Thermal gravimetric analysis (TGA) reveals that they are both stable up to 350 °C (Figure S5). Scanning electron microscopy (SEM) images showed that both of them possess a uniform granular morphology (Figure S6). a)

b)

a) 110

c) 012 102 010

5

210 200

10

022 112

15

20

25

30

35

2 Theta 110

b)

010

5

012102 022 112 210 200

10

15

20

25

30

35

2 Theta Figure 1. PXRD patterns of CCOFs 5 a) and 6 b) with the experimental profiles in black, Pawley refined in red, calculated in blue and the difference between the experimental and refined PXRD patterns, in dark cyan (insert: views of ball-stick models along the c-axis).

The 13C cross-polarization magic angle spinning (CP-MAS) NMR spectrum shows the characteristic signal for the C=N group at ~159 ppm for 5 (Figure S2). The aldehyde carbon peaks were barely observed. The chemical shifts of other fragments are in good agreement with those of the monomers. Conversion of the materials from imine to amide was also confirmed by 13C CPMAS NMR spectroscopy. In the 13C CP-MAS NMR spectrum of 6 at natural abundance, the imine carbon peak at 159 ppm was no longer present after oxidation. Indeed, a new peak, associated with the amide carbonyl, was observed at 166 ppm (Figure S2). In addition, small shifts in the frequencies of the aromatic carbon resonances between 5 and 6 suggests the oxidation of the imine

Figure 2. Structural representations of CCOF 5. a) An adamantine-like cage in the diamond net. b) The structure viewed along the a-axis showing the four-fold interpenetration of a diamond net. c) The two kinds of 1D channels along the c-axis. C gray; N blue; H white; O red.

The crystalline structures of the CCOFs were determined by powder X-ray diffraction (PXRD) analysis with Cu Kα radiation (Figure 1). In light of the orthorhombic phase of 5, a lowersymmetry model was built with space group P2 adapting the unaltered dia-C4-net interpenetrated along the c-axis (Figures 2a and b), which is coherent with the observed PXRD pattern. The lattice modeling and Pawley refinement (Materials Studio, version 7.0) gave optimized parameters of a = 16.97 Å, b = 13.51 Å, c = 16.33 Å, α = 90.0°, β = 108.87° and γ = 90.0° for the unit cell with the space group of P2, which provided two good agreement factors (Rp = 4.55% and Rwp = 5.07%). The experimental PXRD pattern (Figure 1a, black curve) shows the main diffraction peaks at 6.59°, 8.48°, 11.11°, 12.60°, 13.17°, 14.12°, 15.60°, 17.40°, corresponding to the (010), (110), (200), (210), (012), (102), (112), and (022) facets of space group P2 (No. 3), respectively. Several types of other possible 3D structures were generated for them, and non-, twofold-, and threefold-interpenetrated diamond nets for 5 were constructed from the space groups P21212, I222 and P-4, respectively (Figure S7). However, the simulated PXRD patterns from these hypothetical nets did not match the experimental data. The structure of CCOF 6 was also confirmed by PXRD using the same space group (Figure S8). This analysis indicates that the symmetry of 5 (space group P2) is conserved, implying retention of the diamond configuration (Figure 1b). The lattice modeling and Pawley refinement gave optimized parameters of a = 16.98 Å, b =13.47 Å, c = 16.40 Å, α = 90.0°, β= 108.9°and γ = 90.0° for the unit cell with acceptable residuals (Rp = 4.32% and Rwp = 5.66%). A slight change in unit cell parameters was found for the amide CCOF compared with the imine one. The TADDOL units in combination with TAM thus allowed the formation of a diamond network with 1D open channels of 0.58 and 0.71 nm for 5 and 0.51 and 0.75 nm for 6 (Figure 1, the insert). The porosity of the materials was examined by measuring N2 sorption isotherms at 77 K on the fully activated samples. The

2 ACS Paragon Plus Environment

Page 3 of 5

a)

c)

b)

d)

α = 1.19 Rs = 1.52

α = 1.20 Rs = 0.92

α = 1.21 Rs = 1.26

α = 1.17 Rs = 1.44

α = 1.29 Rs = 1.78

α = 1.21 Rs = 1.58

α = 1.33 Rs = 2.47

α = 1.24 Rs = 1.54

0

10

20

30

40

50

0

10

Retention time / min

20

30

40

Retention time / min

50

0

10

20

30

40

Retention time / min

50

60

0

10

20

30

40

50

Retention time / min

Figure 4. a)-d) HPLC separation of racemic 1-phenyl-2-propanol, 1-phenyl-1-pentanol, 1-phenyl-1-propanol, and 1-(4-bromophenyl)ethanol on the CCOF 5 (red line) and 6 (blue line) packed columns, respectively, using hexane/isopropanol (v/v= 99:1) as the mobile phase at a flow rate of 0.2 mL/min.

CCOF 6

CCOF 5

300

3

N2 Uptake (cm /g)

200 6

0.59 nm

4

3

dV (cm /g)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Journal of the American Chemical Society

100

0.74 nm

2 0

0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 Pore Width / nm

0 0.0

0.2

0.4

0.6

0.8

1.0

P/P0 Figure 3. N2 adsorption-desorption isotherms (77 K) and pore size distribution profiles (insert) of CCOFs 5 (red) and 6 (blue).

adsorption curves of the CCOFs exhibited the type-I isotherm (Figure 3), which is the characteristic of microporous materials. Brunauer-Emmett-Teller (BET) surface areas of 655 and 613 m2g1 were estimated for 5 and 6, respectively. Their total pore volumes were calculated to be 0.51 and 0.42 cm3g-1 at P/P0 = 0.99, respectively. The nonlocal density functional theory (NLDFT) gave rise to a narrow pore size distribution with an average pore width 0.62 and 0.74 nm for 5, and 0.59 and 0.72 nm for 6, corresponding to their simulated values (Figure 3, the insert). The chemical stability of the CCOFs was examined by PXRD and sorption after 1 day treatment in boiling water, 12 M HCl (aq) and 1 M NaOH (aq) (Figures S9 and S10). Both CCOFs are stable in boiling water, but 5 showed decreased crystallinity and surface area. The difference between the stabilities of the imine and amide materials is striking in the case of acidic and alkaline conditions, where the amide CCOF retained its crystallinity while the imine one was nearly dissolved and the remaining material was rendered amorphous. The as-treated samples of 6 have a BET surface area of 580 and 477 m2g−1, respectively. A small decrease in signal-tonoise ratio and a decrease of 6% or 22% in surface areas of the amide materials indicate partial structural collapse upon treatment. The two CCOFs packed columns for HPLC were prepared by loading the mixture of the crystalline samples (an average size of ~0.3 µm) and silica (an average size of ~5 µm ) in EtOH into a 20-cm-long 2.3 mm internal diameter (i.d.) stainless steel column. The performance of the column packed with 5 was firstly evaluated by resolution of 1-phenyl-2-propanol. After optimizing mobile phase composition and its flow rate, racemic 1-phenyl-2-

propanol was successfully baseline separated on the CSP with hexane/isopropanol (optimized v/v= 99:1) as the mobile phase at a flow rate of 0.2 mL/min. The separation with a good selectivity factor (α = 1.19) and chromatographic resolution (Rs = 1.52) was achieved within 40 mins, and the elution sequence was the Senantiomer followed by the R-enantiomer. However, as shown in Figure 4, racemic 1-phenyl-1-pentanol, 1-phenyl-1-propanol, and 1-(4-bromophenyl)-ethanol cannot be baseline separated, affording α/Rs = 1.20/0.92, 1.21/1.26 and 1.17/1.44, respectively. Remarkably, the column packed with 6 can baseline resolve all racemates of 1-phenyl-2-propanol, 1-phenyl-1-pentanol, 1phenyl-1-propanol, and 1-(4-bromophenyl)ethanol, affording α/Rs = 1.29/1.78, 1.21/1.58, 1.33/2.47 and 1.24/1.54, respectively (Table S3). The elution order was also the S-enantiomer followed by the R-enantiomer. Besides, other types of racemates such as sulfoxides, carboxylic acids and esters can also be completely or partly resolved on the COF-based CSPs (Figure S16). It appears that, in call cases, 6 showed much improved resolution ability related to 5 under similar conditions. PXRD indicated that the recovered CCOFs after HPLC measurement remained crystalline and structurally intact (Figure S13). Both CCOFs 5 and 6 possessed chiral tubular channels with the maximum aperture sizes of ∼0.71 and 0.75 nm, respectively. The sizes cover the minimum diameters of all tested racemates (∼6.0 Å). The resolution abilities of the CCOFs are likely to come from a combination of the chiral channels with amphiphilic channel interior lined with chiral hydroxyl groups, which may govern the host-alcohol interactions favoring enantioselectivity during the adsorption process.15 To prove this point, 1-(1-naphthyl)-ethanol with a minimum diameter of 0.85 nm being larger than the maximum channel sizes of the CCOFs was selected as an analyte. It is found that the elution appeared with less retention time than those resolved enantiomers, indicating no separation for this large molecule (Figure S11). The oxidation of imine linkages in 5 to amide linkages allows to finely tune the pore interior and affinity to maximize their stereoselective effects and thus to perform highly enantioselective resolution.16 We also fabricated monodispersed amorphous COF@SiO2 and (R,R)-TTA/SiO2 hybrid microspheres and evaluated their chiral recognition ability as CSPs. The results showed that they cannot separate racemic alcohols at all (Figure S15), further highlighting the key role of the crystalline 3D structure of the COF in chiral recognition. To gain further insight into the separation of chiral molecules, an increase in 1-phenyl-2-propanol mass in hexane was injected into the 6-based column for separation. The results showed a few decrease in the retention time for the first eluted enantiomer, while the resolution for the analyte slightly decreased as the mass

3 ACS Paragon Plus Environment

Journal of the American Chemical Society 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

increased. In addition, the chromatographic peak area of each single antipode rose linearly with the increase in the injected mass. The service life of the COF column is found to be at least two months (Figure S12). Chiral HPLC using stereoregular synthetic or natural polymers as CSPs has become one of the most popular ways for chiral separation.17 To develop new type of chromategraphic materials, metal-organic frameworks have recently been explored as CSPs for HPLC separation,18,19 but they in general suffer from the disadvantages of low chemical stability. For the separation of racemic alcohols, the resolution and selectivity factors observed for COF 6 are comparable to or higher than those of reported for MOF-based CSPs (Table S4).19 In summary, we have demonstrated the direct synthesis of the first 3D CCOF by imine condensation of tetrahedral tetraamine and chiral tetraaldehyde building blocks as well as post-synthetic oxidation of the framework to create an isostructural amide-linked CCOF with enhanced chemical stability. PXRD and modeling studies, together with pore size distribution analysis demonstrated that both CCOFs are four-fold interpenetrated microporous frameworks with tubular channels lined with chiral dihydroxy groups. Both of them can work as CSPs of HPLC for separation of racemic alcohols with excellent repeatability and reproducibility, whereas the oxidized CCOF showed superior resolution performance compared with the pristine framework. This work therefore advances COFs as a new platform for chiral resolution and will expand the scope of materials design and engineering to make new type of COFs with unique enantioselective functions. ASSOCIATED CONTENT

Supporting Information Experimental procedures and characterization data. This material is available free of charge via the Internet at http: //pubs.acs.org AUTHOR INFORMATION Corresponding Author [email protected], [email protected] ACKNOWLEDGMENT The authors acknowledge the financial support of the NSFC (21431004, 21522104 and 21620102001), the “973” Program (2014CB932102 and 2016YFA0203400), Key Project of Basic Research of Shanghai (17JC1403100) and the Shanghai Eastern Scholar Program. REFERENCES (1) Côté, A. P.; Benin, A. I.; Ockwig, N. W.; O'Keeffe, M.; Matzger, A. J.; Yaghi, O. M. Science 2005, 310, 1166. (b) Jin, E.; Asada, M.; Xu, Q.; Dalapati, S.; Addicoat, M. A.; Brady, M. A.; Xu, H.; Nakamura, T.; Heine, T.; Chen, Q.; Jiang, D. Science 2017, 357, 673. (2) (a) Kandambeth, S.; Mallick, A.; Lukose, B.; Mane, M. V.; Heine, T.; Banerjee, R. J. Am. Chem. Soc. 2012, 134, 19524. (b) Bunck, D. N.; Dichtel, W. R. J. Am. Chem. Soc. 2013, 135, 14952. (3) (a) Fang, Q.; Zhuang, Z.; Gu, S.; Kaspar, R. B.; Zheng, J.; Wang, J.; Qiu, S.; Yan, Y. Nat. Commun. 2014, 5, 4503. (b) Beaudoin, D.; Maris, T.; Wuest, J. D. Nat. Chem. 2013, 5, 830. (c) Calik, M.; Sick, T.; Dogru, M.; Döblinger, M.; Datz, S.; Budde, H.; Hartschuh, A.; Auras, F.; Bein, T. J. Am. Chem. Soc. 2016, 138, 1234. (d) Zeng, Y.; Zou, R.; Luo, Z.; Zhang, H.; Yao, X.; Ma, X.; Zou, R.; Zhao, Y. J. Am. Chem. Soc. 2015, 137, 1020. (e) Pang, Z.; Xu, S.; Zhou, T.; Liang, R.; Zhan, T.; Zhao, X. J. Am. Chem. Soc. 2016, 138, 4710. (4) (a) Sun, Q.; Aguila, B.; Perman, J.; Earl, L. D.; Abney, C. W.; Cheng, Y.; Wei, H.; Nguyen, N.; Wojtas, L.; Ma, S. J. Am. Chem. Soc. 2017, 139, 2786. (b) Doonan, C. J.; Tranchemontagne, D. J.; Glover, T. G.; Hunt, J. R.; Yaghi, O. M. Nat. Chem. 2010, 2, 235.

Page 4 of 5

(5) (a) Qian, H.; Yang, C.; Yan, X.. Nat. Commun. 2016, 7, 12104. (b) Ning, G.; Chen, Z.; Gao, Q.; Tang, W.; Chen, Z.; Liu, C.; Tian, B.; Li, X.; Loh, K. J. Am. Chem. Soc. 2017, 139, 8897. (6) (a) Bertrand, G. H. V.; Michaelis, V. K.; Ong, T.; Griffin, R. G.; Dincă, M. Proc. Natl. Acad. Sci. U.S.A. 2013, 110, 4923. (b) Chen, L.; Furukawa, K.; Gao, J.; Nagai, A.; Nakamura, T.; Dong, Y.; Jiang, D. J. Am. Chem. Soc. 2014, 136, 9806. (c) Bessinger, D.; Ascherl, L.; Auras, F.; Bein T. J. Am. Chem. Soc., 2017, 139, 12035. (7) (a) DeBlase, C. R.; Silberstein, K. E.; Truong, T.-T.; Abruña, H. D.; Dichtel, W. R. J. Am. Chem. Soc. 2013, 135, 16821. (b) Du, Y.; Yang, H.; Whiteley, J. M.; Wan, S.; Jin, Y.; Lee, S.; Zhang, W. Angew. Chem., Int. Ed. 2016, 55, 1737. (c) Wang, S.; Wang, Q.; Shao, P.; Gan, Y.; Gao, X.; Ma, L., Yuan, S., Ma, X., Zhou, J., Feng, X.; Wang, B. J. Am. Chem. Soc., 2017, 139, 4258. (8) (a) Fang, Q.; Wang, J.; Gu, S.; Kaspar, R. B.; Zhuang, Z.; Zheng, J.; Guo, H.; Qiu, S.; Yan, Y. J. Am. Chem. Soc. 2015, 137, 8352. (b) Mitra, S.; Sasmal, H. S.; Kundu, T.; Kandambeth, S.; Illath, K.; Díaz Díaz, D.; Banerjee, R. J. Am. Chem. Soc. 2017, 139, 4513. (9) (a) Peng, Y.; Huang, Y.; Zhu, Y.; Chen, B.; Wang, L.; Lai, Z.; Zhang, Z.; Zhao, M.; Tan, C.; Yang, N.; Shao, F.; Han, Y.; Zhang, H. J. Am. Chem. Soc. 2017, 139, 8698. (b) Rao, M. R.; Fang, Y.; De Feyter, S.; Perepichka, D. F. J. Am. Chem. Soc. 2017, 139, 2421. (10) (a) Sun, Q.; Aguila, B.; Perman, J.; Nguyen, N.; Ma, S. J. Am. Chem. Soc. 2016, 138, 15790. (b) Ding, S.; Gao, J.; Wang, Q.; Zhang, Y.; Song, W.; Su, C.; Wang, W. J. Am. Chem. Soc. 2011, 133, 19816. (c) Fang, Q.; Gu, S.; Zheng, J.; Zhuang, Z.; Qiu, S.; Yan, Y. Angew. Chem., Int. Ed. 2014, 53, 2878. (d) Vyas, V. S.; Haase, F.; Stegbauer, L.; Savasci, G.; Podjaski, F.; Ochsenfeld, C.; Lotsch, B. V. Nat. Commun. 2015, 6, 8508. (e) Peng, Y.; Hu, Z.; Gao, Y.; Yuan, D.; Kang, Z.; Qian, Y.; Yan, N.; Zhao, D. ChemSusChem 2015, 8, 3208. (11) (a) Wang, X.; Han, X.; Zhang, J.; Wu, X.; Liu, Y.; Cui, Y. J. Am. Chem. Soc. 2016, 138, 12332. (b) Xu, H.; Gao, J.; Jiang, D. Nat. Chem. 2015, 7, 905. (c) Xu, H.; Ding, S.; An, W.; Wu, H.; Wang, W. J. Am. Chem. Soc. 2016, 138, 11489. (d) Zhang, J.; Han, X.; Wu, X.; Liu, Y.; Cui, Y. J. Am. Chem. Soc. 2017, 139, 8277. (e) Han, X.; Xia, Q.; Huang, J.; Liu, Y.; Tan, C.; Cui, Y. J. Am. Chem. Soc. 2017, 139, 8693. (12) (a) Das, S.; Heasman, P.; Ben, T.; Qiu, S. Chem. Rev. 2017, 117, 1515. (b) Bisbey, R. P.; Dichtel, W. R. ACS Cent. Sci. 2017, 3, 533. (13) (a) Uribe-Romo, F. J.; Hunt, J. R.; Furukawa, H.; Klöck, C.; O’Keeffe, M.; Yaghi, O. M. J. Am. Chem. Soc. 2009, 131, 4570. (b) Zhang, Y.-B.; Su, J.; Furukawa, H.; Yun, Y.; Gándara, F.; Duong, A.; Zou, X.; Yaghi, O. M. J. Am. Chem. Soc. 2013, 135, 16336. (c) Lin, G.; Ding, H.; Yuan, D.; Wang, B.; Wang, C. J. Am. Chem. Soc. 2016, 138, 3302. (d) Li, H.; Pan, Q.; Ma, Y.; Guan, X.; Xue, M.; Fang, Q.; Yan, Y.; Valtchev, V.; Qiu, S. J. Am. Chem. Soc. 2016, 138, 14783. (e) Baldwin, L. A.; Crowe, J. W.; Pyles, D. A.; McGrier, P. L. J. Am. Chem. Soc. 2016, 138, 15134. (f) Ma, Y.; Li, Z.; Wei, L.; Ding, S.; Zhang, Y.; Wang, W. J. Am. Chem. Soc. 2017, 139, 4995. (g) Lin, G.; Ding, H.; Chen, R.; Peng, Z.; Wang, B.; Wang, C. J. Am. Chem. Soc. 2017 139, 8705. (14) Waller, P. J.; Lyle, S. J.; Osborn Popp, T. M.; Diercks, C. S.; Reimer, J. A.; Yaghi, O. M. J. Am. Chem. Soc. 2016, 138, 15519. (15) (a) Ward, T. J.; Ward, K. D. Anal. Chem. 2012, 84, 626. (b) Peng, Y.; Gong, T.; Zhang, K.; Lin, X.; Liu, Y.; Jiang, J.; Cui, Y. Nat. Commun. 2014, 5, 4406. (c) Xie, S.; Zhang, Z.; Wang, Z.; Yuan, L. J. Am. Chem. Soc. 2011, 133, 11892. (16) (a) Zhang, S.; Wojtas, L.; Zaworotko, M. J. J. Am. Chem. Soc. 2015, 137, 12045. (b) Zhang, S.; Yang, C.; Shi, W.; Yan, X.; Cheng, P.; Wojtas, L.; Zaworotko, M. J. Chem, 2017, 3, 281. (c) Kuang, X.; Ye, S.; Li, X.; Ma, Y.; Zhang, C.; Tang, B. Chem. Commun. 2016, 52, 5432. (17) (a) Shen, J.; Okamoto, Y. Chem. Rev. 2016, 116, 1094. (b) Andersson, S.; Allenmark, S.; Moller, P.; Persson, B.; Sanchez, D.; J. Chromatogr. A. 1996, 741, 23. (18) (a) Nuzhdin, A. L.; Dybtsev, D. N.; Bryliakov, K. P.; Talsi, E. P.; Fedin, V. P. J. Am. Chem. Soc. 2007, 129, 12958. (b) Zhang, M.; Pu, Z.; Chen, X.; Gong, X.; Zhu, A.; Yuan, L. Chem. Commun. 2013, 49, 5201. (19) (a) Kuang, X.; Ma, Y.; Su, H.; Zhang, J.; Dong, Y.; Tang, B. Anal. Chem. 2014, 86, 1277. (b) Yang, C.; Zheng, Y.; Yan, X. RSC Adv. 2017, 7, 36297. (c) Tanaka, K.; Muraoka, T.; Otubo, Y.; Takahashi, H.; Ohnishi, A. RSC Adv. 2016, 6, 21293. (d) Padmanaban, M.; Muller, P.; Lieder, C.; Gedrich, K.; Grunker, R.; Bon, V.; Senkovska, I.; Baumgartner, S.; Opelt, S.; Paasch, S.; Brunner, E.; Glorius, F.; Klemm, E.; Kaskel, S. Chem. Commun. 2011, 47, 12089.

4 ACS Paragon Plus Environment

Page 5 of 5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Journal of the American Chemical Society

Graphic Content

5 ACS Paragon Plus Environment