Construction of Layered Double Hydroxides ... - ACS Publications

Oct 20, 2017 - NAAM Research Group, Faculty of Science, King Abdulaziz University, Jeddah 21589, Saudi Arabia. §. Department of ... Collaborative Inn...
2 downloads 14 Views 6MB Size
Subscriber access provided by Gothenburg University Library

Article

Construction of Layered Double Hydroxides/Hollow Carbon Microsphere Composites and its Applications for Mutual Removal of Pb(II) and Humic Acid from Aqueous Solutions Shuyi Huang, Shuang Song, Rui Zhang, Tao Wen, Xiangxue Wang, Shujun Yu, Wencheng Song, Tasawar Hayat, Ahmed Alsaedi, and Xiangke Wang ACS Sustainable Chem. Eng., Just Accepted Manuscript • DOI: 10.1021/ acssuschemeng.7b01717 • Publication Date (Web): 20 Oct 2017 Downloaded from http://pubs.acs.org on October 21, 2017

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

ACS Sustainable Chemistry & Engineering is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 44

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

Authors Information The full mailing address of all authors: Shuyi Huang: No.2 Beinong Road, Huilongguan Town, Changping District, School of Environment and Chemical Engineering, North China Electric Power University, Beijing 102206, P. R. China Shuang Song: No.2 Beinong Road, Huilongguan Town, Changping District, School of Environment and Chemical Engineering, North China Electric Power University, Beijing 102206, P. R. China Rui Zhang: No.2 Beinong Road, Huilongguan Town, Changping District, School of Environment and Chemical Engineering, North China Electric Power University, Beijing 102206, P. R. China Tao Wen: No.2 Beinong Road, Huilongguan Town, Changping District, School of Environment and Chemical Engineering, North China Electric Power University, Beijing 102206, P. R. China Xiangxue Wang: No.2 Beinong Road, Huilongguan Town, Changping District, School of Environment and Chemical Engineering, North China Electric Power University, Beijing 102206, P. R. China Shujun Yu: No.2 Beinong Road, Huilongguan Town, Changping District, School of Environment and Chemical Engineering, North China Electric Power University, Beijing 102206, P. R. China Wencheng Song: No.2 Beinong Road, Huilongguan Town, Changping District, School of Environment and Chemical Engineering, North China Electric Power 1

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

University, Beijing 102206, P. R. China Tasawar Hayat: NAAM Research Group, Faculty of Science, King Abdulaziz University, Jeddah 21589, Saudi Arabia Ahmed Alsaedi: NAAM Research Group, Faculty of Science, King Abdulaziz University, Jeddah 21589, Saudi Arabia Xiangke Wang: No.2 Beinong Road, Huilongguan Town, Changping District, School of Environment and Chemical Engineering, North China Electric Power University, Beijing 102206, P. R. China *: Corresponding authors. [email protected] (T. Wen); [email protected] (X. Wang).

2

ACS Paragon Plus Environment

Page 2 of 44

Page 3 of 44

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

Construction of Layered Double Hydroxides/Hollow Carbon Microsphere Composites and its Applications for Mutual Removal of Pb(II) and Humic Acid from Aqueous Solutions Shuyi Huanga, Shuang Songa, Rui Zhanga, Tao Wena,*, Xiangxue Wanga, Shujun Yua, Wencheng Song,a Tasawar Hayatb,c, Ahmed Alsaedib, Xiangke Wanga,b,d* a

College of Environmental Science and Engineering, North China Electric Power

University, Beijing 102206, P.R. China b

NAAM Research Group, Faculty of Science, King Abdulaziz University, Jeddah

21589, Saudi Arabia c

Department of Mathematics, Quaid-I-Azam University, Islamabad 44000, Pakistan

d

Collaborative Innovation Center of Radiation Medicine of Jiangsu Higher Education

Institutions, School for Radiological and Interdisciplinary Sciences, Soochow University, Suzhou 215123, P.R. China *:

Corresponding

authors.

Email:

[email protected]

[email protected] (X. Wang). Tel(Fax): 86-10-61772890.

3

ACS Paragon Plus Environment

(T.

Wen);

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ABSTRACT Development of a highly efficient material with large specific area was scientifically and technologically important for simultaneous elimination of inorganic and organic pollutants from wastewater. In this work, layered double hydroxides (LDHs) coated hollow carbon microsphere composites (HCMSs) (LDHs/HCMSs) were fabricated using carbon spheres as templates via a hydrothermal method and then applied for mutual removal of Pb(II) and humic acid (HA) under various experimental conditions, i.e., pH, ionic strength, contact time, addition sequences and coexisting ions. The results indicated that the co-presence of Pb(II) and HA facilitated single target pollutant (Pb(II) or HA) adsorption at pH < 8.0. The adsorbed HA was responsible for the improvement of Pb(II) adsorption, primarily as a result of the formation of HA-Pb-LDHs/HCMSs ternary complexes. Competitive adsorption of Cu(II), Co(II), Pb(II) and Ni(II) ions on LDHs/HCMSs were also investigated and the LDHs/HCMSs had the affinity in the order of Co(II) < Ni(II) < Cu(II) < Pb(II). Interestingly, in binary/quaternary systems, the results showed that the presence of Cu(II), Co(II) and Ni(II) ions exhibited slightly inhibition on Pb(II) adsorption. However, the total amounts of heavy metal ions adsorbed on LDHs/HCMSs increased with the increase of the heavy metal ions. Results of X-ray photoelectron spectroscopy and Fourier transformed infrared spectroscopy indicated that outer-sphere surface complexation mainly dominated the adsorption of Pb(II) on LDHs/HCMSs, while the adsorption of HA was attributed to surface complexation of the disassociated HA on LDHs/HCMSs. The findings highlighted the novelty synthesis of LDHs/HCMSs and its potential 4

ACS Paragon Plus Environment

Page 4 of 44

Page 5 of 44

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

application for simultaneous removal of different metal ions and natural organic contaminants from wastewater in the environmental pollution cleanup. KEYWORDS: LDHs/HCMSs; Humic acid; Pb(II); Simultaneous removal; Surface complexation

5

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

INTRODUCTION The treatment of wastewater contaminated by toxic heavy metal ions and natural organic pollutants had become one of the most onerous challenges for the sustainable development of human society because of their detrimental effects on environmental protection and human health. Among the toxic heavy metal ions, Pb(II) ions, arising from the metal processing, leaded gasoline, the lead-based paint and battery manufacturing industry, might cause detrimental effects on the intellectual development of human, central nervous function and semi-permanent brain.1 Because of the important biological activity and its adverse influence on human health even at low concentration, Pb(II) ions should be removed from aqueous solutions. At the same time, Pb(II) ions are inevitably coexisted with natural organic matters in aqueous solutions.2-4 For natural organic pollutants, humic acid (HA), a subclass of humic substances which are widely existed in nature and is not easily decomposed by microorganisms, has a strong influence on the physicochemical behaviour of metal ions in natural aqueous systems. Various functional groups (e.g., amine, phenol, hydroxyl and carboxylic groups) of HA could provide considerable sites for binding metal ions and organic molecules, resulting in significant physicochemical behaviour changes of the contaminants in the environment. Moreover, the HA molecules can react with chlorine and produce some hazardous substances such as trihalomethanes and haloacetic acids during the process of the chlorination of drinking water, might cause seriously harmful influence on human health.5 Therefore, it is of great importance to develop advanced technologies and materials to attenuate Pb(II) and 6

ACS Paragon Plus Environment

Page 6 of 44

Page 7 of 44

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

HA concentrations in the natural water. A variety of technologies have been applied to minimize the amount of Pb(II) and HA in aqueous solutions, such as reverse osmosis,6 biosorption,7 electro-chemical,8 photodegradation,9 chemical coagulation,10 ion exchange11 and adsorption.12 Nevertheless, most methods had been found to be limited by high investment, poor efficiency and secondary pollution and thereby greatly restricted their application in environmental pollution remediation. For example, ion exchange exhibited high efficiency, but it was limited in practical applications due to high cost required in the regenerative process. Compared to these methods, the adsorption technique had the advantages of trouble-free operation, low cost and wide adaptability. Therefore, the adsorption technique was regarded as one of the most important considerable technologies in industrial applications and has been widely used in the enrichment of different kinds of pollutants from large volumes of aqueous solutions. Layered double hydroxides (LDHs), a new class of inorganic layered materials, have received multidisciplinary attention because of their unique physicochemical properties.13 The LDHs are generally represented by the formula [M2+1-xN3+x(HO−)2]x+ [(Xn−)x/n yH2O]x-, where the M2+ and N3+ represent divalent metal cations (Ca2+, Mg2+, Co2+, Cu2+, Ni2+, Zn2+, Mn2+) and trivalent metal cations (Al3+, Co3+, Fe3+, Cr3+, Mn3+), respectively, and Xn− is the intercalating anions. LDHs have large interlayer space with considerable anions for the ion-exchange, and the positively charged layers would make them excellent adsorbents for efficient removal of negatively charged contaminants or the ion-exchange of cations through the substitution with M2+ ions in 7

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 8 of 44

LDHs.14-16 Hence, LDHs were regarded as a kind of essential adsorbents for cations/ anions and organic compounds. Meanwhile, the abundant functional groups of carbon-based nanomaterials are useful for the binding of toxic organic pollutions and heavy metal ions.17-19 Considering the above-mentioned properties, one can introduce LDHs to carbon microsphere surface to construct the calcined LDHs hollow carbon microsphere hierarchical nanostructure materials with large surface area and stable hollow structure via an environmentally friendly approach (Figure 1a). The calcined LDHs/hollow carbon microsphere composites (CLDHs/HCMSs) can be converted to LDHs/hollow carbon microsphere composites (LDHs/HCMSs) with the property known as “memory effects”,20 and then the LDHs/HCMSs can be applied as the efficient adsorbents for the elimination of Pb(II) and HA from wastewater. This research contributed to the understanding of HA and Pb(II) uptake to LDHs/HCMSs. The physicochemical properties of LDHs/HCMSs were carefully characterized

by

Thermogravimetric

Fourier (TG),

transformed X-ray

infrared

photoelectron

(FTIR)

spectroscopy,

spectroscopy

(XPS)

,

Brunauer-Emmett-Teller (BET) and Zeta potential analysis. The mutual effects of Pb(II) and HA on LDHs/HCMSs were systemically investigated. Potential adsorption of coexisting heavy metal ions (i.e., Cu2+, Ni2+, Co2+,Pb2+) was also studied to have an insight into the interaction of HA and Pb(II) on LDHs/HCMSs. EXPERIMENTAL SECTION Materials and Chemicals. All reagents used in this experiment were purchased in analytical grade. Glucose (C6H12O6·H2O), magnesium nitrate hexahydrate 8

ACS Paragon Plus Environment

Page 9 of 44

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

(Mg(NO3)2·6H2O), urea, aluminium nitrate nonahydrate (Al(NO3)3·9H2O), sodium hydroxide

(NaOH),

chloroacetic

acid

(C2H3ClO2),

nitric

acid

(HNO3),

hydrochloric acid (HCl) were purchased from Sinopharm Chemical Reagent Beijing Cl., Ltd (Beijing, China). The humic acid (HA) sample was obtained from Heilongjiang Province, China. And the HA constituents were approximately 0.50% S, 3.53% H, 4.22% N, 31.31% O and 60.44% C. Synthesis of LDHs/HCMSs. The carbon spheres were firstly synthesized through a traditional hydrothermal method.21 Briefly, 21 g of glucose was dissolved in 70 mL deionized water; then the above solution was hydrothermally treated at 180 oC for 5 h. After the reaction, the black products were rinsed using ethanol and deionized water several times and collected by centrifugation. Ultimately, the powders were gathered after vacuum drying at 60 °C for 12 h. The hollow carbon microsphere coated with Mg-Al-LDHs were obtained through an alkaline hydrothermal treatment using carbon microspheres as the template. In a typical synthesis, 0.36 g of carbon spheres was dispersed in 70 mL Al(NO3)3·9H2O (0.37 g) and Mg(NO3)2·6H2O (0.50 g) solution by stirring (IKA: C-MAG HS7, 500 rpm) for 12 h to ensure that Mg2+ and Al3+ can contact with carbon microspheres substantially. Then, 1.25g of urea was stirred with this suspension for 1 h. Then the black homogeneous suspension was transferred to a Teflon-lined autoclave and maintained at 90 oC for 4 h, followed by filtrating and rinsing with Mill-Q water and ethanol for 3 times. At last, Mg-Al-LDHs/carbon microsphere composites (Mg-Al-LDHs/CMSs) were obtained after drying at 60 9

ACS Paragon Plus Environment

o

C for 12 h. The

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Mg-Al-LDHs/CMSs were heated to 400 °C at the heating rate of 2 °C·min−1 and then annealed at 400 °C for 4 h to get CLDHs/HCMSs. The schedule for the synthesis of CLDHs/HCMSs was described in Figure 1a. The abundant adsorption sites (e.g. –OH and –COOH groups) of carbonaceous microspheres would be responsible for coordination with Mg2+ and Al3+. Characterization. To detect the interior structure and the change of elements, transmission electron microscopy (TEM) and energy-dispersive X-ray (EDX) spectroscopy elemental mapping were acquired on a FEI Tecnai G2 F20 electron microscope at 200 kV. The scanning electron microscopy (SEM) technique was applied to investigate the surface morphology using a Hitachi S4800 microscope. The X-ray photon spectroscopy (XPS) spectra were performed on the ESCALAB 250 Xi XPS of Thermo Scientific to achieve the detailed information of adsorption mechanism. Zeta potential value was measured on a Zetasizer (Nano-ZS) from Malvern Instruments. Thermogravimetric (TG) measurement was performed using a TG-50 thermal analyzer under air at a heating rate of 10 oC·min-1. The Fourier transformed infrared (FTIR) spectra were collected on the Nicolet Magana-IR 750 spectrometer over the range of 400~4000 cm-1. The N2-Brunauer-Emmett-Teller (BET) specific surface area test was measured using the Micromeritics ASAP 2010 at 77 K. It was worth noting that the samples were heated to 80 °C and maintained at the temperature of 80 °C for 24 h before each each measurement. Batch adsorption experiments. The batch adsorption measurements were conducted at 298 K and pH 5.0 ± 0.05 in polyethylene tubes. 0.06 g of 10

ACS Paragon Plus Environment

Page 10 of 44

Page 11 of 44

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

LDHs/HCMSs powders were dispersed into 100 mL Milli-Q water and a 0.6 g/L stock adsorbent concentration was achieved. For Pb(II) and HA adsorption, the LDHs/HCMSs stock solution, the NaNO3 background electrolyte solution, Milli-Q water and the Pb(II) (200 mg·L-1) or HA (400 mg·L-1) solutions were added into the polyethylene tubes in sequence to obtain the desired different component concentrations. The desired HA and Pb(II) solutions were added into the polyethylene tubes simultaneously when the mutual removal of HA and Pb(II) on the LDHs/HCMSs was investigated. After adjusting the pH value of the suspensions in each tube by adding 0.1 and/or 0.01 M HNO3 and/or NaOH, then the suspensions were vigorously stirred at 298 K for 24 h. After that, the above suspensions were centrifuged at 10000 rpm for 30 min to separate the solid and liquid phases. The HA concentration in supernatant was measured by spectrophotometry at the wavelength of 256 nm. The adsorption percentage and the adsorption capacity of Pb(II) and HA on solid phases were calculated from Eqs. (1) and (2):

Adsorption =

qe =

( C0 − Ce ) ×100% C0

(1)

V × ( C0 − Ce ) m

(2)

where Ce (mg·L-1)and C0 (mg·L-1) were the the equilibrium concentration after adsorption and the initial concentration, respectively, m (mg) was the dosage of LDHs/HCMSs and V (mL) was the total volume of the suspension. The effect of the addition sequences on HA and Pb(II) adsorption to 11

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

LDHs/HCMSs was further investigated. Specifically, the addition sequences of HA and Pb(II) were described as: (1) In the (LDHs/HCMSs-Pb)-HA system, LDHs/HCMSs, Pb(II), and NaNO3 were equilibrated for 24 hours before contacting with HA. (2) In (LDHs/HCMSs-HA)-Pb system, LDHs/HCMSs, HA, and NaNO3 were equilibrated for 24 hours before contacting with Pb(II). The batch experiments were performed in duplicate to observe the reproducibility, and all experimental result was the average value of triplicate measurement within relative errors of ~5%. RESULTS AND DISCUSSION Characterization of LDHs/HCMSs. The morphologies and microstructures of as-prepared carbon microspheres and LDHs/HCMSs were measured by SEM and TEM images. From Figures 1b and 1d, the uniform carbon microspheres showed smooth surfaces with the average size of approximately 150 nm. After coated with LDHs and pyrolysis of the composites, the LDHs/HCMSs displayed an interconnected 3D framework with many junctions and exhibited a rough surface, suggesting that LDHs were coated on the surface of carbon spheres successfully (Figures 1c and 1e). As anticipated, the TEM image further confirmed the formation of the hollow structure. The EDX element mapping (Figure 1f) showed the homogeneous distribution of C, O, Mg, Al and Pb elements in the LDHs/HCMSs. After Pb(II) adsorption, the LDHs/HCMSs kept the original morphologies. The EDX spectrum (Figure 2a and 2b) also confirmed the existence

12

ACS Paragon Plus Environment

Page 12 of 44

Page 13 of 44

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

of the aforementioned elements, indicating the homogeneous distributions of LDHs coating on the surfaces of hollow carbon. The FT-IR spectra of LDH samples before and after HA/Pb(II) adsorption were shown in Figure 2c. The intense broad peak at 3440 cm-1 was resulted from the stretching vibration of structural O–H groups in association with the interlayer H2O molecules, LDH layers hydrogen bonding and carboxyl groups.20 The adsorption band at 1423 cm−1 was attributed to the carbonate anion stretching vibrations, indicating that some CO32− ions existed in LDHs/HCMSs.22,

23

The

peaks in the range of 400-800 cm-1 were assigned to the lattice vibrations of O-M-O, M-O-M and M-O lattice vibrations (M referred to Mg and Al).24 These peaks confirmed the successful modification of carbon spheres by Mg-Al-LDHs. Thermogravimetric (TG) analysis was employed to estimate the thermal stability of LDHs/HCMSs. As illustrated in Figure 2d, the thermal evolution of LDHs/HCMSs underwent three weight loss steps as follows: the first weight loss (∼7 wt %) from room temperature to 150 °C was attributed to the loss of the surface adsorbed H2O; and then the second weight loss step (∼8 wt %) in the region of 150-380 °C arose from the decomposition of brucite-like layers and intercalated CO32− anions, oxygen-containing groups;23 and finally the third weight loss (∼8 wt %) in the region of 400−550 °C was assigned to the destruction of carbon skeleton. This was in accordance with the result of EDX spectrum. Thus, one can speculate that the carbon skeleton in LDHs/HCMSs was not effectively removed in the synthesis process and maintained the hierarchical hollow structure. 13

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 14 of 44

The N2-BET specific area of the LDHs/HCMSs was examined via N2 adsorption-desorption measurements. As plotted in Figure 2e, the adsorption isotherm can be classified as the mixed characteristics of type II and IV, and the hysteresis loop was found in the range of 0.8–1.0 P/P0, implying the coexistence of nanoporous, mesoporous and macroporous structures in LDHs/HCMSs, which was further supported by the distribution of pore sizes (Figure 2f). The LDHs/HCMSs displayed a narrow pore size distribution centred at the diameter of 2.7 nm. Furthermore,

the

Brunauer–Emmett–Teller

(BET)

surface

area

of

the

LDHs/HCMSs was calculated to be 231 m2·g−1. The large surface area and abundant functional groups made the LDHs/HCMSs to be an effectual material for the preconcentration of HA or Pb(II) ions from large volume of solutions. The XPS spectra of LDHs/HCMSs before/after HA and Pb(II) adsorption were presented in Figure 3. In the survey spectra (Figure 3a), four apparent peaks of C 1s, O 1s, Mg 1s and Al 2p illustrated that carbon, oxygen, magnesium and aluminium were the predominant elements of the LDHs/HCMSs.12 For comparison, the Pb(II) peak was found in the survey spectrum of Pb(II)-laden LDHs/HCMSs. The high-resolved C 1s spectrum of LDHs/HCMSs (Figure 3c) can be deconvoluted into three components, i.e., the carboxylate carbon (O-C=O, 289.2 eV), the carbon in C-O (285.8 eV) and non-oxygenated C (284.5 eV).25 The specific peak at 289.2 eV showed a wider peak area rather than other peaks, indicating that the dominated oxygen-containing functional group was O−C=O. The carboxylate carbon signal further implied the presence of intercalated CO32− in 14

ACS Paragon Plus Environment

Page 15 of 44

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

the layer of LDHs/HCMSs, which was also confirmed by FT-IR result. It was interesting that the O 1s spectrum of LDHs/HCMSs (Figure 3d) could be deconvoluted into three peaks at 532.5, 531.1, and 529.9 eV, which represented the binding energies of different oxygen form in OH−, O−, and chemical or physical adsorbed H2O, respectively.26 More detailed discussion of the XPS spectra of LDHs/HCMSs after Pb(II)/HA adsorption were described in the following adsorption mechanism section. Effect of pH. The influence of solution pH on Pb(II) and HA adsorption to LDHs/HCMSs were presented in Figure 4a. One can see that the adsorption of Pb(II) was deeply dependent on pH and reached the maximum amount at pH ~6.5. With the increase of pH from 3.0 to 6.0, the adsorption efficiency of Pb(II) on LDHs/HCMSs increased dramatically from ~10% to ~75%, maintained the high level in the pH range of 6.0-8.0, and then decreased with the increase of pH (pH > 8.0). The variation of pH can either promote or suppress the efficiency of Pb(II) adsorption on LDHs/HCMSs, which may be attributed to the relative distribution of Pb(II) species in solution and the surface properties of LDHs/HCMSs. As shown in Figure 4c, the zero point of charge (pHzpc) of LDHs/HCMSs was about 9.6, meaning that the LDHs/HCMSs’ surface charge was positive at pH < 9.6 and kept negative at pH > 9.6. The surface of LDHs/HCMSs contained abundant functional groups (i.e., hydroxyl and carboxylic groups) which could be protonated at low pH values ([SOH+H+⇔SOH2+]) or deprotonated at high pH values ([SOH⇔SO−+H+]) (SOH represents the surface functional groups). From the hydrolysis constants of Pb(II) (i.e., log K1 =6.48, log K2 =11.16, log K3 =14.16 (Kn = [Pb(OH)n2−n]·[H+]/[Pb2+])), the Pb(II) ions 15

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

presented the species of Pb2+, Pb(OH)+, Pb(OH)3− and Pb3(OH)42+ at variable pH values, and the relative distribution of Pb(II) species was computed by Visual MINTEQ ver. 3.0 (Figure 4d).12 Pb2+ was the dominant species in solution at pH < 6.0. At low pH values, the low sorption of Pb2+ was attributed to the strong electrostatic repulsion between Pb2+ ions and the positive surface charge of adsorbents. With the increase of solution pH, the electrostatic repulsion between Pb2+ ions and LDHs/HCMSs became weak, and thereby the adsorption of Pb2+ increased with solution pH increasing. The main species of Pb(II) were Pb2+, Pb(OH)+ and Pb3(OH)42+ in the pH range of 6.0-9.6. The surface charge of LDHs/HCMSs was still positive at pH < 9.6, which suggested that the high removal efficiency of Pb(II) was primarily ascribed to strong surface complexation or the ion exchange with Mg2+ ions in LDHs/HCMSs. As the solution pH further increased, Pb(OH)3− became the main species progressively, and it was constrained to be adsorbed on the negative LDHs/HCMSs because of the electrostatic repulsion. The surface became more negatively charged with the increase of solution pH, which resulted in the decrease of the negative Pb(II) species adsorption on the negatively charged LDHs/HCMSs because the electrostatic repulsion became stronger at higher pH values. At the same time, the competition between Pb(OH)3− and OH− also gave rise to the dramatic decrease of Pb(II) adsorption on LDHs/HCMSs. From the batch adsorption results, one can see that the electrostatic repulsion presented in the whole pH range. However, the LDHs/HCMSs still exhibited high adsorption ability in the pH range of 5-9, suggesting that the elimination of Pb(II) was mostly related to strong surface complexation or the substitution of Mg2+ in LDHs/HCMSs. From Figure 2b, one can see that the atomic radio of Mg/Al after Pb(II) 16

ACS Paragon Plus Environment

Page 16 of 44

Page 17 of 44

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

adsorption was about 0.33, which was lower than the ratio of Mg/Al (1.72) in LDHs/HCMSs.27 The decrease of Mg/Al ratio suggested that Mg2+ participated in the ion exchange of Pb(II) in the adsorption process. The pH-dependent adsorption of HA on LDHs/HCMSs was also investigated. From Figure 4b, it was found that the adsorption percentage of HA on LDHs/HCMSs decreased from ~96% to ~30% with the increase of pH from 3.0 to 11.0. The pHzpc of HA was ~2.0, suggesting that the charge of HA molecules was negative at pH > 2.0.28 Therefore, high adsorption of HA on LDHs/HCMSs was attributed to the electrostatic attraction between the positively charged LDHs/HCMSs and negatively charged HA. Generally, large HA molecules probably “huddle up” at low pH values and the HA molecules have a smaller volume because of the low charge development, meaning more binding sites on the surface of LDHs/HCMSs can interact with HA molecules and form more surface complexes,29 which also results in the high adsorption of HA at low pH values. However, HA contained a great amount of carboxyl and phenolic groups, suggesting that HA became negative at high solution pH because of the deprotonation reactions of oxygen-containing functional groups. The adsorption of HA on LDHs/HCMSs was a combined effect of electrostatic attraction between LDHs/HCMSs and HA molecules and electrostatic repulsion between HA molecules themselves, which led to the gradually expanding volume of HA molecules with pH increasing. Thus, both the increasing solubility of HA molecules and the negative surface charge of LDHs/HCMSs at high pH were responsible for the rapid decrease of HA removal due to the electrostatic repulsion. Figures 4a and 4b also showed the mutual effect of Pb(II) and HA adsorption to 17

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

LDHs/HCMSs. It was found that Pb(II) adsorption on LDHs/HCMSs in the presence of HA was improved at pH < 9 and achieved the maximum adsorption at pH ~ 5.5, which was lower than the pH value in the absence of HA. Pb2+ ions can not only be substituted by Mg2+ in LDHs/HCMSs but also form strong complexes with surface adsorbed HA at low pH values, resulting in the formation of Pb-HA-LDHs/HCMSs ternary complexes. The surface adsorbed HA molecules can serve as “bridge” between Pb(II) and LDHs/HCMSs.30 At pH < 5.5, the surface of HA molecule became more negative with increasing pH, indicated the easier formation of strong complexes with pH increasing due to the increasing electrostatic attraction of HA molecule and Pb2+. However, Pb(OH)+ became the main species progressively pH > 5.5, the adsorption percentage of Pb(II) decreased with the decreasing electrostatic attraction of Pb(II) and HA, but was still higher than it in the absence of HA. At pH > 9, Pb(II) was mainly present as negatively charged Pb(OH)3- species in solution, which was hard to form complexes with the negatively charged HA molecules due to electrostatic repulsion.31 Consequently, the competitive adsorption of Pb(II) with the dissolved HA on LDHs/HCMSs and the electrostatic repulsion among Pb(OH)3−, HA molecules and LDHs/HCMSs resulted in the quick decrease adsorption of Pb(II) at high solution pH condition.32 Effect of Ionic Strength. The removal percentages of Pb(II) on LDHs/HCMSs as a function of solution pH under different NaNO3 concentrations were given in Figure 5a. The removal of Pb(II) increased with ionic strength decreasing from 0.1 M to 0.001 M. Generally, the ionic strength can affect Pb(II) adsorption on LDHs/HCMSs 18

ACS Paragon Plus Environment

Page 18 of 44

Page 19 of 44

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

by influencing the interface potential and double layer thickness. The ionic strength-dependent adsorption showed that ion exchange or outer-sphere surface complexation contributed mainly to the adsorption of Pb(II) on LDHs/HCMSs.33 This phenomenon might be ascribed to three possible reasons: (1) The Pb(II) ions combined with more H2O molecules at low ionic strength rather than at high ionic strength. The high ionic strength could reduce the actively coefficient of Pb(II) ions in aqueous solutions and restrict their transfer from solution to the surface of LDHs/HCMSs; (2) Pb(II) ions interacted with LDHs/HCMSs by electrostatic reaction and formed electrical double layer complexes with LDHs/HCMSs. In other words, the concentration of NaNO3 affected the ion exchange of Pb2+ with Mg2+ on the surface of LDHs/HCMSs; (3) ionic strength affected on particle aggregation through influencing the electrostatic interactions. In other words, high ionic strength can reduce the electrostatic repulsion and then increase the particle aggregation, which resulted in the decrease of the available binding sites and then decreased the adsorption performance of Pb(II) ions on LDHs/HCMSs.34 Figure 5b showed that the adsorption efficiency of HA to LDHs/HCMSs decreased with the increase of the ionic strength obviously. It can be obtained that nitrate ions affected HA adsorption by competing with HA molecules to be attracted by positively charged LDHs/HCMSs. Thereby, the main adsorption mechanism of HA adsorption might be the formation of surface complexation between HA and LDHs/HCMSs. Considering the property that HA has a tendency to precipitation in the presence of metal ions and at high ionic strength, blank experiments in the absence of adsorbent were showed in Figure S1. 19

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 20 of 44

The precipitation percentages of HA at pH 5.0 were about 5.2%, 10.2% and 15.3% at 0.001 M, 0.01 M and 0.1 M NaNO3, which were far lower than the elimination percentages of HA in the presence of LDHs/HCMSs, indicating that the precipitation of HA hardly affected the adsorption experiments and the precipitated HA might be removed from solution by the formation of LDHs/HCMSs-Pb-HA ternary complexes. Adsorption Isotherms and Effect of Addition Sequences. Figure 6 showed the adsorption isotherms of Pb(II) ions and HA on LDHs/HCMSs. All the isotherms displayed a tendency that qe (mg·g-1) increased rapidly at low initial Pb(II) or HA concentrations and then increased gradually at high-level Pb(II) or HA loading conditions. With the purpose of understanding the interaction mechanism, the Langmuir model and Freundlich model were employed to simulate the experiment data. Langmuir isotherm model was expressed in Eq. (3):

qe =

K L qmax Ce 1 + K L Ce

(3)

Freundlich isotherm model was described according to Eq. (4): 1

qe = K F Ce n

(4)

where Ce (mg·L-1) represented the equilibrium concentration of Pb(II) or HA in aqueous solutions; qmax (mg·g-1) was the amount of Pb(II) or HA adsorbed on per weight unit of LDHs/HCMSs after adsorption equilibration; KL (L·mg-1) was a Langmuir constant related to the heat of adsorption; KF (mg1-n·Ln·g-1) was the Freundlich constant, representing saturation adsorption capability of the adsorbent.

20

ACS Paragon Plus Environment

Page 21 of 44

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

The corresponding parameters were tabulated in Table 1. From the correlation coefficients (R2), it was clear that Langmuir model fitted the adsorption isotherms better than Freundlich model. From Langmuir model simulation, the qmax value of Pb(II) was 291.46 mg·g-1 in the presence of HA, which was much higher than that of Pb(II) (qmax = 205.68 mg·g-1) in the absence of HA at pH 5.0 and 298 K. The qmax value of HA was 467.54 mg·g-1 in the presence of Pb(II) at pH 5.0 and 298 K, which was also significantly higher than that of HA (qmax = 300.46 mg·g-1) without Pb(II). The results demonstrated that the surface adsorbed Pb(II) enhanced HA adsorption through the formation of Pb(II)-HA complexes on LDHs/HCMSs. The adsorbed HA molecules on solid surface could also act as “bridge” between Pb(II) and LDHs/HCMSs and thereby enhanced Pb(II) adsorption to LDHs/HCMSs. The results were crucial for the real applications of LDHs/HCMSs in the simultaneous elimination of HA and Pb(II) from the natural water system. In natural environment, the co-presence of heavy metal ions and organic pollutants could be simultaneously removed through the formation of strong surface complexes on LDHs/HCMSs. Moreover, the comparison of adsorption capacities of LDHs/HCMSs with LDHs-based materials or carbon materials were shown in Table 2.23,29,35-39 It can be obtained that the LDHs/HCMSs with high surface area had remarkable adsorption capability for both Pb(II) and HA.

Various studies gave the effect of addition sequences of heavy metal ions and natural organic materials. The adsorption of Pb(II) and HA in LDHs/HCMSs-Pb-HA ternary system for different Pb(II)/HA addition sequences were further investigated. 21

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 22 of 44

As shown in Figure 6, one can see that the addition sequences made no difference on the adsorption of mutual removal of HA and Pb(II) in (LDHs/HCMSs-Pb)-HA and LDHs/HCMSs-Pb-HA systems, which was consistent with the previous study.40 However, the qmax value of Pb(II) adsorption was slightly decreased in the (LDHs/HCMSs-HA)-Pb system, indicating that the complexation between HA and LDHs/HCMSs occupied the adsorption and complexation sites of HA and LDHs/HCMSs and thus decreased the amount of effective sites for Pb2+ adsorption.

Adsorption Kinetic of Pb(II) and HA. The kinetic adsorption data of Pb(II) and HA on LDHs/HCMSs was described by the pseudo-second-order and pseudo-first-order models. The pseudo-first-order model was presented as the following equation: ln(qe − qt ) = ln qe − k1t

(5)

The pseudo-second-order model equation was expressed as: t 1 t = + 2 qt k2 qe qe

(6)

where qe (mg·g-1) was the amount of HA or Pb(II) adsorbed at equilibrium time, qt (mg·g-1) was the amount of HA or Pb(II) adsorbed on LDHs/HCMSs at time t (min), k1 and k2 (mg·g-1·min-1) were the pseudo-first-order model rate and the pseudo-second-order rate, respectively, respectively. Form the linear plots of ln (qe qt) versus t and t/qt versus t, the values of k1, k2 and estimated qe can be obtained, and the parameters were tabulated in Table 3. Figure 7 showed the kinetic adsorption curves of Pb(II) and HA on LDHs/HCMSs. The adsorption of both target pollution increased quickly within the first contact time 22

ACS Paragon Plus Environment

Page 23 of 44

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

of 30 min, and then achieved adsorption equilibrium after 60 min (Figures 7a and 7c). This adsorption tendency was probably ascribed to the abundant active sites and functional groups on LDHs/HCMSs at the initial reaction time, which were available for the binding of Pb(II) and HA.24 It was apparent that the adsorption of Pb(II) in the presence of HA was rather faster than that of Pb(II) in the absence of HA, whereas little difference was found for the adsorption kinetic of HA in the presence or absence of Pb(II), although the adsorption percentage of HA coexisted with Pb(II) was a little higher than that of HA in the absence of Pb(II) (Figure 7c). Clearly, the R2 values of pseudo-second-order model (Figures 7b and 7d) were >0.999, which were higher than those of pseudo-first-order model, indicating that the pseudo-second-order model could better describe kinetic adsorption processes. This phenomenon demonstrated that rate-limiting step might be chemisorption process involving valance forces through exchanging or sharing electrons between target pollution and adsorbents.41 Consequently, it implied that the main interaction of Pb(II) and HA with LDHs/HCMSs was dominted by strong surface complexes or chemisorption than the mass transport.42

Adsorption Mechanisms. To elucidate the interaction mechanism of Pb(II)/HA with LDHs/HCMSs, the FT-IR spectra of LDHs/HCMSs after Pb(II) or HA adsorption were measured (Figure 2c). After Pb(II) adsorption, the characteristic peak at 3440 cm−1 was slightly increased, suggesting that the adsorption induced the increase of surface -OH groups, which might be arised from the absorption of Pb(II) hydroxide on the assembly. Notably, the peak shift from 1423 to 1379 cm−1 after Pb(II) 23

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

adsorption might be ascribed to the precipitation of Pb3(CO3)2(OH)2,43 which was due to the contact between Pb2+ in solution and intercalated CO32− anions in LDHs. For the HA adsorption, an intense adsorption band at ~1585 cm−1, which was attributed to the aromatic C=C vibrations or hydrogen bonded C=O of quinones in HA molecules, appeared in the FT-IR spectrum of HA-laden LDHs/HCMSs, suggesting the successfully adsorption of HA molecules on the surface of LDHs/HCMSs.31 It showed that the intensity of the band at 1423 cm−1 after HA adsorption became significantly lower, which was related to the ligand exchange reaction between carbonate ions and HA molecules.44 The ion exchange indicated that the LDHs/HCMSs show higher affinity to HA than carbonate. The XPS spectra of LDHs/HCMSs before and after HA/Pb(II) adsorption were given in Figure 3. In the high-resolution of Pb 4f spectrum (Figure 3b), the characteristic doublet peaks of Pb 4f5/2 and Pb4f7/2 were observed at 138.2 and 143.2 eV, which were higher than their binding energy values in aqueous Pb-O complexes (136.9 and 141.7 eV), were in accordance with those in Pb(II)−CO32− binding form, implying the specific binding of Pb(II) on LDHs/HCMSs as the speciation of Pb3(CO3)2(OH)2.23,26 Compared with Al 2p peak (~73.8 eV) in LDHs/HCMSs (Figure 3f), the binding energy of Al 2p after HA adsorption shifted to 74.3 eV, indicating that the main phase of Al changed from Al-O to Al-OH in the HA-laden LDHs/HCMSs.45 In comparison with Al 2p spectrum, a remarkable decrease of Mg 1s intensities (Figure 3e) was observed from Pb(II)-laden (or HA-laden) LDHs/HCMSs, showing the strong interaction between Pb(II) ions (or HA) with Mg atoms. The EDX result (Figure 2a and 2b) showed that the atomic radio of 24

ACS Paragon Plus Environment

Page 24 of 44

Page 25 of 44

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

Mg/Al after Pb(II) adsorption was about 0.33, which was lower than the ratio of Mg/Al (1.72) calculated from the preparation method.46 The decrease of Mg content in LDHs/HCMSs after Pb(II) or HA adsorption was in connection with the pKsp values of Mg(OH)2(s). which resulted in the decrease of Mg 1s intensities on Pb(II)-laden (or HA-laden) LDHs/HCMSs. The decreased of Mg 1s intensities on HA-laden LDHs/HCMSs was ascribed to the property of Mg-Al-LDHs that releasing Mg2+ in aqueous solution. Notably, the decrease of Mg 1s intensity in Pb(II)-laden LDHs/HCMSs was more significant than it in the HA-laden LDHs/HCMSs, indicating that Mg2+ took part in the Pb(II) binding on LDHs/HCMSs and the mechanism of Pb(II) adsorption was partly due to ion exchange with Mg2+. For the Pb(II)-laden LDHs/HCMSs, the contents of O−, OH− and H2O, which were calculated from the peak areas, varied from about 19.21%, 62.45% and 18.34% (LDHs/HCMSs before Pb(II) adsorption) to about 5.95%, 74.34% and 19.70% (after Pb(II) adsorption), respectively. It can be found that the specific OH− peak area increased and the O− peak area decreased, suggesting the generation of Pb(II) hydroxides.26 For the HA-laden LDHs/HCMSs, the peak of O-C=O shifted to lower binding energy after HA adsorption, demonstrating that HA could be easily adsorbed on LDHs/HCMSs’ surface and had strong ligand exchange reaction with the intercalated CO32−. Jobbagy and Regazzoni47 reported that at pH 5-9, almost 20% of magnesium ion was leached out from Mg-Al-LDHs, while the dissolution of aluminium ion was insignificant. The dissociation equations of Mg2+ and Al3+ from LDHs/HCMSs was 25

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 26 of 44

expressed as: Mg(OH)2(s) → Mg2+ + OH−

(7)

Al(OH)3(s) → Al3+ + OH−

(8)

According to the pKsp values of Mg(OH)2(s) (11.2) and Al(OH)3(s) (32.9), the theoretical value calculated equilibrium concentration of Mg(II) was 5.6 × 106 M at pH 5.0, while that of Al(III) ions was 2.0 × 10−6 M.48,49 Consequently, the dissociation of Mg from LDHs/HCMSs might take a critical part in Pb(II) uptake processes. The slight intensity change of Al 2p spectra after the adsorption of HA or Pb(II) also confirmed that part dissociation of Al ions from LDHs/HCMSs. Based on the aforementioned discussion, the interaction mechanism of HA and Pb(II) on LDHs/HCMSs was illustrated in Figure 8.

Competitive Adsorption of Pb(II) and Other Heavy Metal Ions. The individual and competitive divalent ions adsorption (Cu(II), Co(II), Pb(II) and Ni(II)) on LDHs/HCMSs in the absence/presence of HA were carried out at the initial concentration of 20 ppm. Figure 9a showed that LDHs/HCMSs can simultaneously remove Pb2+, Ni2+, Cu2+, and Co2+ ions from solutions and hold high affinity in the order of Co2+ < Ni2+ < Cu2+ < Pb2+. In comparison, the adsorption of Pb2+, Cu2+, Ni2+ and Co2+ ions on LDHs/HCMSs all increased in the presence of HA (Figure 9b). As compared in the absence of other heavy metal ions, the adsorption capacity of Pb(II) was higher than that of Pb(II) in the presence of Cu(II), Co(II) and Ni(II) ions, suggesting that Pb(II) adsorption was slightly inhibited in the presence of other heavy metal ions because of the competitive interaction behaviour of other heavy metal ions. 26

ACS Paragon Plus Environment

Page 27 of 44

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

However, the sum amount of target ions adsorbed on LDHs/HCMSs increased with the increases of other metal ions. Therefore, the competitive adsorption results confirmed that LDHs/HCMSs exhibited fine applicability for the simultaneous elimination of various metal ions from wastewater, which would be significant for the practical application of LDHs/HCMSs in the elimination of different metal ions from wastewaters in environmental pollution cleanup.

CONCLUSION In summary, we herein reported the synthesis of hierarchical structure LDHs/HCMSs using a hydrothermal method. The adsorption behaviour of LDHs/HCMSs toward the simultaneous adsorption of HA and Pb(II) was systematically investigated. The results indicated that the LDHs/HCMSs had superior capacities for the simultaneous removal of HA/Pb(II) ions from solutions. The findings presented herein demonstrated that LDHs/HCMSs were promising materials for the efficient elimination of different kinds of organic/inorganic substances in wastewater purification.

ASSOCIATED CONTENT Supporting Information. The effect of pH and ionic strength on the precipitation of HA in the absence of adsorbent and the precipitation percentage of HA at different ionic strength were performed.

AUTHOR INFORMATION Corresponding Author * Fax: +86-10-61772890, Phone: +86-10-61772890. E-mail: [email protected] (T. 27

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Wen); [email protected] (X. Wang).

ORCID Tao Wen: 0000-0001-9089-3196 Xiangke Wang: 0000-0002-3352-1617

Notes The authors declare no competing financial interest.

ACKNOWLEDGEMENTS The financial support from NSFC (21607042, 21577032), the National Special Water Programs (2015ZX07204-007, 2015ZX07203-011), the Fundamental Research Funds for the Central Universities (JB2015001, 2017MS045), the Priority Academic Program Development of Jiangsu Higher Education Institutions and the Jiangsu Provincial Key Laboratory of Radiation Medicine and Protection are acknowledged.

REFERENCES (1) Naseem, R.; Tahir, S. S. Removal of Pb(II) from aqueous/acidic solutions by using bentonite as an adsorbent. Water Res. 2001, 35, 3982–3986. (2) Ma,Q.; Cheng, H.; Yu, Y.; Huang, Y.; Lu, Q.; Han, S.; Chen, J.; Wang, R.; Fane, A. G.; Zhang H. Preparation of Superhydrophilic and Underwater Superoleophobic Nanofiber‐Based Meshes from Waste Glass for Multifunctional Oil/Water Separation. Small 2017, 13, 1700391. (3) Bi, H.; Yin, Z.; Cao, X.; Xie, X.; Tan, C.; Huang, X.; Chen, B.; Chen, F.; Yang, Q.; Bu, X.; Lu, X.; Sun, L.; Zhang, H. Carbon fiber aerogel made from raw cotton: a novel, efficient and recyclable sorbent for oils and organic solvents. Adv.Mater. 2013, 25, 5916-5921. (4)

Bi, H.; Huang, X.; Wu, X.; Cao, X.; Tan, C.; Yin, Z.; Lu, X.; Sun, L.; Zhang, H. Carbon

28

ACS Paragon Plus Environment

Page 28 of 44

Page 29 of 44

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

microbelt aerogel prepared by waste paper: an efficient and recyclable sorbent for oils and organic solvents. Small 2014, 10, 3544-3550. (5) Chang, M. Y.; Juang, R. S. Adsorption of tannic acid, humic acid, and dyes from water using the composite of chitosan and activated clay. J. Colloid Interface Sci. 2004, 278, 18–25. (6) Kurniawan, T. A.; Chan, G. Y. S.; Lo, W. H.; Babel, S. Physico-chemical treatment techniques for wastewater laden with heavy metals. Chem. Eng. J. 2006, 118, 83–98. (7) Yan, G.; Viraraghavan, T. Heavy metal removal in a biosorption column by immobilized M. rouxii biomass. Bioresour. Technol. 2001, 78, 243–249. (8) Kongsricharoern, N.; Polprasert, C. Chromium removal by a bipolar electro-chemical precipitation process. Water Sci. Technol. 1996, 34, 109–116. (9) Wang, G. S.; Liao, C. H.; Wu, F J. Photodegradation of humic acids in the presence of hydrogen peroxide. Chemosphere 2001, 42, 379–387. (10)

Zou, Y. D.; Wang, X. X.; Ai, Y. J.; Liu, Y. H.; Li, J. X.; Ji, Y. F.; Wang, X. K. Coagulation

Behaviour of Graphene Oxide on Nanocrystallined Mg/Al Layered Double Hydroxides: Batch Experimental and Theoretical Calculation Study. Environ. Sci. Technol. 2016, 50, 3658–3667. (11)

Rengaraj, S.; Yeon, K. H.; Moon, S. H. Removal of chromium from water and wastewater by

ion exchange resins. J. Hazard. Mater. 2001, 87, 273–287. (12)

Zou, Y. D.; Wang, X. X.; Ai, Y. J.; Liu, Y. H.; Ji, Y. F.; Wang, H. Q; Hayat, T.; Alsaedi, A.;

Hu, W. P.; Wang, X. K. β-Cyclodextrin modified graphitic carbon nitride for the removal of pollutants from aqueous solution: experimental and theoretical calculation study. J. Mater. Chem. A 2016, 4, 14170–14179. (13)

Li, L.; Ma, R.; Iyi, N.; Ebina, Y.; Takada, K.; Sasaki, T. Hollow nanoshell of layered double

29

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

hydroxide. Chem. Commun. 2006, 2, 3125–3127. (14)

Das, N. N.; Konar, J.; Mohanta, M. K.; Srivastava, S. C. Adsorption of Cr(VI) and Se(IV)

from their aqueous solutions onto Zr4+-substituted ZnAl/MgAl-layered double hydroxides: Effect of Zr4+ substitution in the layer. J. Colloid Interface Sci. 2004, 270, 1–8. (15)

You, Y.; Vance, G. F.; Zhao, H. Selenium adsorption on Mg-Al and Zn-Al layered double

hydroxides. Appl. Clay Sci. 2001, 20, 13–25. (16)

You, Y.; Zhao, H.; Vance, G. F. Surfactant-enhanced adsorption of organic compounds by

layered double hydroxides. Colloids Surfaces A Physicochem. Eng. Asp. 2002, 205, 161–172. (17)

Ma, Q.; Yu, Y.; Sindoro, M.; Fane, A. G.; Wang, R.; Zhang, H. Carbon‐Based Functional

Materials Derived from Waste for Water Remediation and Energy Storage. Adv. Mater. 2017, 1605361. (18)

Ma, Q.; Cheng, H.; Fane, A. G.; Wang, R.; Zhang, H. Recent dvelopment of advanced

materials with special wettability for selective oil/water separation. Small 2016, 12, 2186-2202. (19)

Chen, B.;Ma, Q.; Tan, C.; Lim, T.; Huang L.; Zhang H. Carbon-Based Sorbents with

Three-Dimensional Architectures for Water Remediation. Small 2015, 11, 3319-3336. (20)

Yu, X. Y.; Luo, T.; Jia, Y.; Xu, R. X.; Gao, C.; Zhang, Y. X.; Liu, J. H.; Huang, X. J.

Three-dimensional hierarchical flower-like Mg–Al-layered double hydroxides: highly efficient adsorbents for As(v) and Cr(vi) removal. Nanoscale 2012, 4, 3466–3474. (21)

Hu, H.; Cheng, H.; Liu, Z.; Li, G.; Zhu, Q.; Yu, Y. In Situ Polymerized PAN-Assisted S/C

Nanosphere with Enhanced High-Power Performance as Cathode for Lithium/Sulfur Batteries. Nano Lett. 2015, 15, 5116–5123. (22)

Yu, S.; Wang, X.; Chen, Z.; Wang, J.; Wang, S.; Hayat, T.; Wang, X. Layered double

hydroxide intercalated with aromatic acid anions for the efficient capture of aniline from aqueous

30

ACS Paragon Plus Environment

Page 30 of 44

Page 31 of 44

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

solution. J. Hazard. Mater. 2017, 321, 111–120. (23)

Zhang, F.; Song, Y.; Song, S.; Zhang, R.; Hou, W. Synthesis of magnetite-graphene

oxide-layered double hydroxide composites and applications for the removal of Pb(II) and 2,4-dichlorophenoxyacetic acid from aqueous solutions. ACS Appl. Mater. Interfaces 2015, 7, 7251–7263. (24)

Zou, Y.; Wang, X.; Chen, Z.; Yao, W.; Ai, Y.; Liu, Y.; Hayat, T.; Alsaedi, A.; Alharbi, N. S.;

Wang, X. Superior coagulation of graphene oxides on nanoscale layered double hydroxides and layered double oxides. Environ. Pollut. 2016, 219, 107–117. (25)

Wen, T.; Wu, X. L.; Tan, X. L.; Wang, X. K.; Xu, A. W. One-pot synthesis of water-swellable

Mg-Al layered double hydroxides and graphene oxide nanocomposites for efficient removal of As(V) from aqueous solutions. ACS Appl. Mater. Interfaces 2013, 5, 3304–3311. (26)

Liu, M.; Wang, Y.; Chen, L.; Zhang, Y.; Lin, Z. Mg(OH)2 supported nanoscale zero valent

iron enhancing the removal of Pb(II) from aqueous solution. ACS Appl. Mater. Interfaces 2015, 7, 7961–7969. (27)

Gong, J. M.; Liu, T.; Wang, X. Q.; Hu, X. L.; Zhang, L. Z. Efficient Removal of Heavy

Metal Ions from Aqueous Systems with the Assembly of Anisotropic Layered Double Hydroxide Nanocrystals @ Carbon Nanosphere. Environ. Sci. Technol. 2011, 45, 6181–6187. (28)

Yan, W. L.; Bai, R. Adsorption of lead and humic acid on chitosan hydrogel beads. Water

Res. 2005, 39, 688–698. (29)

Yang, S. T.; Hu, J.; Chen, C. L.; Shao, D. D.; Wang, X. K. Mutual Effects of Pb ( II ) and

Humic Acid Adsorption on Multiwalled Carbon Nanotubes/Polyacrylamide Composites from Aqueous Solutions. Environ. Sci. Technol. 2011, 45, 3621–3627.

31

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

(30)

Wang, X. X.; Li, J. X.; Dai, S. Y.; Hayat, T.; Alsaedi, A.; Wang, X. K. Interactions of Eu(III)

and 243Am(III) with humic acid-bound γ-Al2O3 studied using batch and kinetic dissociation techniques. Chem. Eng. J. 2015, 273, 588–594. (31)

Strathmann, T. I.; Myneni, S. C. B. Effect of soil fulvic acid on nickel(II) sorption and

bonding at the aqueous-boehmite (γ-AlOOH) interface. Environ. Sci. Technol. 2005, 3, 4027–4034. (32)

Karlsruhe, F. Sorption of Eu(III) on Humic Acid or Fulvic Acid Bound to Hydrous Alumina

Studied by SEM-EDS , XPS , TRLFS , and Batch Techniques. Environ. Sci. Technol. 2008, 42, 6532–6537. (33)

Song, W. C.; Wang, X. X.; Wen, T.; Yu, S. J.; Zou, Y. D.; Sun, Y. B.; Hayat, T.; Wang, X. K.

Immobilization of As(V) in Rhizopus oryzae Investigated by Batch and XAFS Techniques. ACS Omega 2016, 1, 899–906. (34)

Mercer, K. L.; Tobiason, J. E. Removal of arsenic from high ionic strength solutions: Effects

of ionic strength, pH, and preformed versus in situ formed HFO. Environ. Sci. Technol. 2008, 42, 3797–3802.

(35)

Wang, R. X.; Wen, T.; Wu, X. L.; Xu, A. W. Highly efficient removal of humic acid

from aqueous solutions by Mg/Al layered double hydroxides–Fe3O4 nanocomposites. RSC Adv. 2014, 4, 21802-21809. (36)

Wang, X. L.; Tao, S.; Xing, B. S. Sorption and competition of aromatic compounds and

humic acid on multiwalled carbon nanotubes. Environ. Sci. Technol. 2009, 43, 6214–6219. (37)

Tian, X.; Zhou, S.; Zhang, Z.; He, X.; Yu, M.; Lin, D. Metal impurities dominate the

sorption of a commercially available carbon nanotube for Pb(II) from water. Environ. Sci. Technol. 2010, 44, 8144–8149. 32

ACS Paragon Plus Environment

Page 32 of 44

Page 33 of 44

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

(38)

Carnizello, A. P.; Marçal, L.; Calefi, P. S.; Nassar, E. J.; Ciuffi, K. J.; Trujillano, R.;

Vicente, M. A.; Korili, S. A.; Gil, A. Takovite-Aluminosilicate nanocomposite as adsorbent for removal of Cr(III) and Pb(II) from aqueous solutions. J. Chem. Eng. Data 2009, 54, 241–247. (39)

Xu, D.; Tan, X. L.; Chen, C. L.; Wang, X. K. Removal of Pb(II) from aqueous solution

by oxidized multiwalled carbon nanotubes. J. Hazard. Mater. 2008, 154, 407–416. (40)

Reiller, P.; Casanova, F.; Moulin, V. Influence of addition order and contact time on thorium

(IV) retention by hematite in the presence of humic acids. Environ. Sci. Technol. 2005, 39, 1641-1648. (41)

Wang, H.; Ma, L.; Cao, K.; Geng, J.; Liu, J.; Song, Q.; Yang, X.; Li, S. Selective solid-phase

extraction of uranium by salicylideneimine-functionalized hydrothermal carbon. J. Hazard. Mater. 2012, 229, 321–330. (42)

Zhao, Y.; Li, J.; Zhao, L.; Zhang, S.; Huang, Y.; Wu, X.; Wang, X. Synthesis of

amidoxime-functionalized Fe3O4@SiO2 core-shell magnetic microspheres for highly efficient sorption of U(VI). Chem. Eng. J. 2014, 235, 275–283. (43)

Shan, R.; Yan, L.; Yang, K.; Hao, Y.; Du, B. Adsorption of Cd(II) by Mg-Al-CO3- and

magnetic Fe3O4/Mg-Al-CO3-layered double hydroxides: Kinetic, isothermal, thermodynamic and mechanistic studies. J. Hazard. Mater. 2015, 299, 42–49. (44)

Gao, C.; Yu, X.; Lou, T.; Jia, Y.; Sun, B.; Liu, J.; Huang, X. Millimeter-sized Mg–Al-LDH

nanoflake impregnated magnetic alginate beads (LDH-nMABs): a novel bio-based sorbent for the removal of fluoride in water. J. Mater. Chem. A 2014, 2, 2119-2128. (45)

Stevenson, F. J.; Goh, K. M. Infrared spectra of humic acids and related substances.

Geochim. Cosmochim. Acta 1971, 35, 471–483. (46)

Goh, K. H.; Lim, T. T.; Dong, Z. Enhanced arsenic removal by hydrothermally treated

33

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

nanocrystalline Mg/Al layered double hydroxide with nitrate intercalation. Environ. Sci. Technol. 2009, 43, 2537–2543. (47)

Jobbágy, M.; Regazzoni, A. E. Dissolution of nano-size Mg-Al-Cl hydrotalcite in aqueous

media. Appl. Clay Sci. 2011, 51, 366–369. (48)

Zhi, P. X.; Guo, Q. L. Hydrothermal synthesis of layered double hydroxides (LDHs) from

mixed MgO and Al2O3: LDH formation mechanism. Chem. Mater. 2005, 17, 1055–1062. (49)

Wu, X. L.; Tan, X. L.; Yang, S. T.; Wen, T.; Guo, H. L.; Wang, X. K.; Xu, A. W. Coexistence

of adsorption and coagulation processes of both arsenate and NOM from contaminated groundwater by nanocrystallined Mg/Al layered double hydroxides. Water Res. 2013, 47, 4159-4168.

34

ACS Paragon Plus Environment

Page 34 of 44

Page 35 of 44

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

Figure. 1 Schematic illustration of the approach used for the synthesis of LDHs/HCMSs. SEM images of (b) as-prepared bare carbon spheres and (c) LDHs/HCMSs, and the corresponding TEM images of (d) bare carbon spheres and (e) LDHs/HCMSs, respectively. (f) Elemental mapping of C, O, Al, Mg and Pb of Pb(II)-laden LDHs/HCMSs.

35

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

(b)

(a) Mg

C Al

Courts

Courts

O C

Pb

Al

O

Mg

0

500

1000

1500

2000

2500

0

3000

500

1000

105

(c)

2000

Weight (%)

LDHs/HCMSs+Pb

7%

90

150 oC

8%

85

380 oC

LDHs/HCMSs+HA

8%

80 1423 1585

448 685

500

1000

1500

3000

550 oC

75

3440

100

3500

200

300

400

500

600

700

800

Temperature (oC)

Wavenumber (cm-1) 0.45

(e)

dV/dlog(D) Pore Volume (cm /g)

350

3000

(d)

95

553 786

2500

100

LDHs/HCMSs

Intensity (a.u.)

1500

Energy (keV)

Energy (keV)

300

0.40

(f)

-1

Quantity Adsorbed (cm3/g STP)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 36 of 44

Desorption Adsorption

250 200 150 100

231 m2/g

50 0.0

0.2

0.4

0.6

0.8

1.0

2.7 nm

0.35 0.30 0.25 0.20 0.15 0.10 2

Relative Pressure (P/P0)

3

4

5

6

7

8 9

Pore Diameter (nm)

Figure 2. EDX of (a) LDHs/HCMSs and (b) Pb(II)-laden LDHs/HCMSs. (c) FTIR spectra of the samples before and after Pb(II) and HA adsorption, (d) TG curve of the LDHs/HCMSs, (e) Nitrogen adsorption-desorption isotherms and (f) pore size distribution of LDHs/HCMSs.

36

ACS Paragon Plus Environment

Page 37 of 44

(a)

(b) intensity (a.u.)

O 1s C 1s

1200

1000

800

600

400

Pb 4f5/2 138.2 eV 143.2 eV

Al 2p Mg 2p

Mg 1s

LDHs/HCMSs + HA

LDHs/HCMSs

Pb 4f Pb 4f7/2

Pb 4f

intensity (a.u.)

LDHs/HCMSs + Pb

200

148

0

144

Binding Energy (eV)

(c)

284.5

140

289.2

(d)

C 1s

529.9 LDHs/HCMSs

532.5

LDHs/HCMSs+Pb

LDHs/HCMSs+HA

288

284

LDHs/HCMSs+HA

536

280

532

(f) Intensity (a.u.)

Mg 1s

LDHs/HCMSs LDHs/HCMSs+Pb(II) LDHs/HCMSs+HA

1308

1304

1300

528

524

Binding Energy (eV)

Binding Energy (eV)

(e)

132

O 1s

531.1

Intensity (a.u.)

Intensity (a.u.)

LDHs/HCMSs

LDHs/HCMSs+Pb

292

136

Binding Energy (eV)

285.8

Intensity (a.u.)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

Al 2p

73.8

LDHs/HCMSs

LDHs/HCMSs+Pb(II) 74.3 LDHs/HCMSs+HA

1296

76

Binding Energe (eV)

72

68

Binding Energe (eV)

Figure 3. (a) XPS survey of LDHs/HCMSs before and after Pb(II) and HA adsorption. XPS high-resolution spectra of (b) Pb 4f, (c) C 1s, (d) O 1s (e) Mg 1s and (d) Al 2p for LDHs/HCMSs before and after Pb(II) and HA adsorption.

37

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

100

(a)

(b)

100 80 Adsorption (%)

Adsorption (%)

80 60 40 20

20 mg/L Pb(II) 20 mg/L Pb(II) + 20 mg/L HA

60 40

20 mg/L HA 20 mg/L HA + 20 mg/L Pb(II)

20

0 2

3

4

5

6

7

8

9

10

11

12

2

3

4

5

6

pH

7

(c)

9

80

pHZPC=9.6

10

Pb2+

3

60 40 (O H) 2 4 +

0 20

Pb

-10 0

-20 6

7

8

9

10

Pb(OH) -

Pb( OH )2 (a q)

20

5

12

11

2

3

4

5

6

3

percent (%)

30

4

11

(d) Pb(OH)+

3

10

100

40 Zeta potencial (mV)

8

pH

50

7

8

9

10

11

12

pH

pH

Figure 4. Effects of pH on the (a) Pb(II) and (b) HA adsorption on LDHs/HCMSs. T = 298 K, m/V = 0.1 g·L-1, C[Pb(II)] initial = 20 mg·L-1, C(HA)initial = 20 mg·L-1, and I = 0.01 M NaNO3. (c) Zeta potential of LDHs/HCMSs. (d) The distribution of Pb(II) species in aqueous solution in the presence of 0.01 M NaNO3.

(a)

100

(b)

100

Adsorption (%)

80 Adsorptio n (%)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 38 of 44

60 40 0.001M NaNO3

20

0.01M NaNO 3

80 60 40

0.001M NaNO3 0.01M NaNO3

20

0.1M NaNO3

0.1M NaNO 3

0

0

2

3

4

5

6

7

8

9

10

11

12

2

3

4

pH

5

6

7

8

9

10

11

12

pH

Figure 5. Adsorption of (a) Pb(II) and (b) HA on LDHs/HCMSs as a function of 38

ACS Paragon Plus Environment

Page 39 of 44

initial pH and different ionic strength T = 298 K, m/V = 0.1 g·L-1, C[Pb(II)]

initial

=

20.0 mg·L-1, and C(HA)initial = 20.0 mg·L-1.

360

(a)

520

320

(b)

480 440

280

400 qt (mg/g)

240 qt (mg/g)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

200 No HA LDHs/HCMSs-Pb-HA (LDHs/HCMSs-HA)-Pb (LDHs/HCMSs-Pb)-HA

160 120 10

20

30

40

50

320 280 No Pb(II) LDHs/HCMSs-Pb-HA (LDHs/HCMSs-Pb)-HA (LDHs/HCMSs-HA)-Pb

240 200 160

80 0

360

0

60

10

Ce (mg/L)

20

30

40

50

60

Ce (mg/L)

Figure 6. Adsorption isotherms of (a) Pb(II), (b) HA and the mutual effects of Pb(II) and HA adsorption on LDHs/HCMSs. pH = 5.0, T = 298 K, m/V = 0.1 g·L-1. Symbols denote experimental data, the solid lines represent the Langmuir model simulation, and the dashed lines represent the Freundlich model. C[Pb(II)] and C(HA)initial = 20.0 mg·L-1.

39

ACS Paragon Plus Environment

initial

= 20.0 mg·L-1,

ACS Sustainable Chemistry & Engineering

3.0 200

(b)

(a) 2.5

160 t/qt (min*g*mg-1)

-1

qt (mg*g )

2.0

120

1.5

80

1.0

40

No HA Add 20 mg/L HA

No HA Add 20 mg/L HA

0.5

0 0.0 0

50

100

150

200

250

300

350

400

0

50

100

Reaction time (min)

240

150

200

250

300

350

400

Reaction time (min)

(c)

(d)

2.0

200 t/qt (min*g*mg-1)

1.6 160 -1

qt (mg*g )

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 40 of 44

1.2

120

0.8

80 40

No Pb(II) Add 20 mg/L Pb(II)

No Pb(II) Add 20 mg/L Pb(II)

0.4

0 0.0 0

50

100

150

200

250

300

350

400

0

50

100

150

200

250

300

350

400

Reaction time (min)

Reaction time (min)

Figure 7. Adsorption kinetic curves of Pb(II) (a) and HA (c) on LDHs/HCMSs, and the linear fit of experimental data of Pb(II) (b) and HA (d) obtained using the pseudo-second-order kinetic model with or without the presence of HA or Pb(II). T = 298 K, m/V = 0.1 g·L-1, I = 0.01 M NaNO3, pH = 5.0, C[Pb(II)] and C(HA)initial = 20.0 mg·L-1.

40

ACS Paragon Plus Environment

initial

= 20.0 mg·L-1,

Page 41 of 44

Figure 8. Schematic diagram of adsorption of Pb(II) and HA on LDHs/HCMSs.

500 400 300

500

Pb(II) Cu(II) Co(II) Ni(II) Sum

(b) Add 20 mg/L HA

400 Adsorption (mg/g)

(a) Without HA Adsorption (mg/g)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

200 100 0

300

Pb(II) Cu(II) Co(II) Ni(II) Sum

200 100 0

Figure 9. The individual and competitive adsorption capacities of Pb2+, Cu2+ and Co2+ and Ni2+ on LDHs/HCMSs without (a) or with (b) HA (C0 = 20 mg·L-1, pH = 5.0, m/V = 0.1 g·L-1, T = 298 K, and I = 0.01 M NaNO3).

41

ACS Paragon Plus Environment

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 42 of 44

Table 1. The parameters calculated from the Langmuir and Freundlich models for Pb(II) and HA adsorption on LDHs/HCMSs. Langmuir qmax(mg·g-1)

KL(L·mg-1)

Freundlich RL2

KF (mg1-n·Ln·g-1)

n

R2

Pb

205.68

1.94

0.986

122.69

6.460

0.910

Pb+HA

291.46

1.04

0.981

138.54

4.320

0.919

HA

300.46

1.77

0.942

203.18

8.966

0.909

HA+Pb

467.54

1.16

0.968

251.92

5.372

0.853

Table 2. Comparison of the adsorption capacities of LDHs-based materials or carbon materials. Surface area Adsorbents

qmax (mg·g-1) Reference

(m2·g−1)

Pb(II)

HA

LDHs

22

-

225.6

[35]

LDHs–Fe3O4

70

-

353.82

[35]

Multiwalled Carbon Nanotubes

86

-

82

[36]

90.95

29.71

12.52

[29]

LDHs/HCMSs

231

205.68

300.46

This work

Magnetite-GO-LDHs

74.9

173

-

[23]

260.99

27.3

-

[37]

Takovite-Aluminosilicate Nanocomposite

256

205

-

[38]

Oxidized MWCNTs

197

4.1

-

[39]

MWCNTs/PAAM

MWCNTs

42

ACS Paragon Plus Environment

Page 43 of 44

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

Table 3. Kinetic modeling of Pb(II) and HA adsorption on LDHs/HCMSs. Pseudo-first-order model

Pseudo-second-order model

k1 (g/mg·min)

qe (mg·g-1)

R2

Pb

0.167

125.75

0.998

0.0046

128.21

0.999

Pb+HA

0.172

175.79

0.991

0.0025

182.15

0.999

HA

0.566

181.23

0.936

0.0258

182.15

0.999

HA+Pb

0.287

192.96

0.998

0.0119

193.80

0.999

k2 (g/mg·min)

43

ACS Paragon Plus Environment

qe (mg·g-1)

R2

ACS Sustainable Chemistry & Engineering

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

For Table of Contents Use Only Synopsis The LDHs/HCMSs composites showed high simultaneous elimination of Pb(II) and HA through the formation of strong surface complexes in environmental pollution cleanup.

44

ACS Paragon Plus Environment

Page 44 of 44