Controlled Growth of BiOCl with Large {010} Facets for Dye Self

Research Article pubs.acs.org/journal/ascecg

Controlled Growth of BiOCl with Large {010} Facets for Dye SelfPhotosensitization Photocatalytic Fuel Cells Application Lei Zhang,† Cheng-Gang Niu,*,† Geng-Xin Xie,*,‡ Xiao-Ju Wen,† Xue-Gang Zhang,† and Guang-Ming Zeng† †

Downloaded via UNIV OF KANSAS on January 21, 2019 at 02:42:48 (UTC). See https://pubs.acs.org/sharingguidelines for options on how to legitimately share published articles.

College of Environmental Science Engineering, Key Laboratory of Environmental Biology Pollution Control, Ministry of Education, Hunan University, Changsha, 410082, China ‡ Urban Construction and Environmental Engineering, Chongqing University, Chongqing, 400044, China S Supporting Information *

ABSTRACT: BiOCl with {010} facets could be a promising material for photodegradation and energy conversion devices such as dye selfphotosensitization photocatalytic fuel cells (DSPFCs). However, the {010} facets usually diminish rapidly during the growth process as the result of its high surface energies. In this work, we reported a simple and efficient method to prepare BiOCl with tunable exposed {010} facets. It was found that the solvent used in the synthesis process had important roles in the formation of ultrathin construction and the growth of {010} facets by controlling the [H+]. For decreasing the surface energy and promoting the growth of high-active {010} facets, the thickness of BiOCl and the areas of {001} were reduced in its forming process. We had demonstrated that the enhancement of visible light-harvesting and photosensitization activity of BiOCl was primarily attributed to the decrease of thickness and the growth of {010} facets which could provide large surface areas and more active sites for dye absorption and photoelectron transfer. The BiOCl samples with tunable exposed {010} areas were evaluated as photoanode materials in DSPFCs. As expected, owing to its strong dye absorption capability and high transfer efficiency of charge carriers, the DSPFC with optimal performance was obtained by employing RhB as fuel when BiOCl possessed the larger areas of {010} facets and became a thinner nanosheet structure. Also, the Jsc and Voc of DSPFC were measured to be 0.0058 mA/cm2 and 0.689 V, respectively. Meanwhile, approximately 67% color removal was achieved on BiOCl{010}-Pt cell by treating 40 mL of 5 mg/L RhB under visible light for 240 min, which was much higher than that of P25-Pt (4%). KEYWORDS: BiOCl{010}, low [H+], large surface area, DSPFCs, visible light

■

INTRODUCTION

The dye self-photosensitization photocatalytic fuel cells (DSPFCs) are developed to fulfill the highly visible lightharvesting and effective photosensitization degradation.15,16 Compared to PFCs, the generation of photoelectrons that came from excited dye molecules usually is much easier owing to the wide light absorption region of dye molecules.17 Moreover, the loss of photoelectrons is small and the recombination rate of charge carriers is low in DSPFCs, because the valence band of the semiconductor is not involved in the process of the photosensitization reaction.18,19 BiOCl can be used as a novel promising material for DSPFC application owing to its unique electronic structure and surface properties. Although the BiOCl cannot be photoexcited directly under visible light because of its wide band gap, it was demonstrated that the BiOCl with {010} facets exhibited excellent dye self-photosensitization performance. On one hand, the BiOCl layered structure

Environmental pollution and excessive energy consumption have caused great attention worldwide. Since the discovery of the photocatalytic splitting of water into hydrogen over TiO2 semiconductor materials under UV light,1 photo fuel cells (PFCs) have been demonstrated as a promising and potential technique for addressing and relieving the intense pressure between environment and energy.2−5 In PFC systems, the photoanode utilizes solar energy as impetus and contaminant as fuel to simultaneously achieve energy conversion and pollutant degradation.6 Currently, the research of PFC devices assembled with TiO2 semiconductor materials achieved impressive achievement under UV,3,7,8 but the limited visible lightharvesting and the presence of surface states seriously impeded their wide application.9,10 Although quantum dots, such as CdS and PbS, can be employed to enhance the visible light absorption capacity and photoelectron transfer efficiency,11,12 the toxicity of quantum dots13 and the instability of CdS14 are of concern for applications. © 2017 American Chemical Society

Received: December 23, 2016 Revised: March 28, 2017 Published: April 19, 2017 4619

DOI: 10.1021/acssuschemeng.6b03150 ACS Sustainable Chem. Eng. 2017, 5, 4619−4629

Research Article

ACS Sustainable Chemistry & Engineering

Figure 1. XRD patterns of the BiOCl samples prepared in different solvent: (a) survey, (b) the characteristic peak of (001) and (110), and the specific value of (110) and (001) peak (inset).

consisting of [Bi2O2]2+ layers sandwiched between two slabs of halogen ions can induce the formation of internal static electric fields and endow it with an open channel feature, which is beneficial for the photoelectron transfer.20 Moreover, the conduction band of BiOCl (−1.1 eV)21,22 is more negative than that of TiO2 (−0.29 eV);23 therefore, the formation of O2•− active species [E(O2/O2•−) (−0.046 eV)]24 on BiOCl is much easier. The O2•− active species possesses high oxidation activity for further pollutant decomposition. On the other hand, the BiOCl with dominant {010} facets has excellent dye absorption capacity and photosensitization performance due to its large surface areas and more surface active sites, which are favorable for enhancing the light-harvesting.18 The dye absorption capability and mobility of charge carriers are the two major impact factors for DSPFC performance. Therefore, the controlled synthesis of BiOCl with a high percentage of {010} facets has important meaning for obtaining highperformance DSPFCs. Unfortunately, the highly active facets usually diminish rapidly during the growth process as a result of their high surface energies.25,26 In this study, a series of BiOCl materials with tunable exposed {010} facets were synthesized by a facile strategy. The impacts of solvent used in the synthesis process on the nanostructure of BiOCl and the growth of {010} facets were discussed in detail. The experiments on the photodegradation of Rhodamine B contaminant were carried out to assess the photosensitization performance of as-prepared BiOCl and investigate the relationship between {010} facets and photocatalytic activity. Moreover, the photovoltaic performances of DSPFCs assembled with BiOCl photoanodes were researched by employing RhB as fuel. Owing to the strong dye absorption capability and high photoelectron transfer efficiency of {010} facets, the BiOCl with the largest {010} facets exhibited superior photovoltaic and RhB decomposition performance than P25 and BiOCl{001}. We expect our work to open a new avenue for the wide application of BiOCl in environment protection and energy, and provide new ideas on exploitation and synthesis of photoanodes materials for high-performance DSPFCs.

■

Rhodamine B (RhB), and sodium sulfate (Na2SO4) were purchased from Sinopharm Chemical Reagent Co., Ltd. All chemicals were of analytical reagent grade and were used without further purification. Preparation of Photocatalysts. In a typical procedure, 2.0 g of Bi(NO3)3·5H2O was added to 5 mL of ammonium hydroxide (NH4OH) at room temperature with continuous ultrasound. After 30 min, 2 mL of solution was added dropwise into 100 mL of anhydrous ethanol that contained 4 mL of saturated sodium chloride solution. Then, the solution turned white, which indicated the formation of BiOCl nanostructure. The mixture solution was allowed to react at room temperature for 24 h under autogenous pressure. After the reaction finished, 20 mL of EG was poured into the white solution with continuous stirring to remove the remaining reagent. After 10 min, the white resulting precipitates were collected, washed with EG and ethanol thoroughly by filtering with a Φ = 0.22 μm organic membrane filter, and dried at 60 °C. The product obtained was denoted BiOCl-NH4OH. In order to research the role of solvent in the synthesis, other BiOCl samples were also prepared under the same conditions but, instead of using NH4OH, using (CH2OH)2, CH3COOH, H2O, and HNO3 solution as the solvent, respectively. BiOCl{001} with large surface areas was synthesized by the reported method.27 Characterization. The powder X-ray diffraction (XRD) patterns measurements were investigated using Rigaku D/max 2500 X-ray diffractometer with Cu Kα radiation (λ = 0.15406 nm), the working voltage operated at 40 kV, and 250 mA. The morphologies of the samples were examined by the environment scanning electron microscope (SEM, Hitachi S-4800) with 5.0 kV scanning voltages. Transmission electron microscopy (TEM) and high-resolution transmission electron microscopy (HRTEM) analysis were conducted on Tecnai G2 F20 at an accelerating voltage of 200 kV. The UV−vis absorption spectrum (DRS) was carried out on a UV−vis spectrophotometer (Hitachi U-4100) from 200 to 800 nm with pure BaSO4 as the reflectance standard material. A nitrogen-adsorption system (ASAP-2020) was carried out to record the BET specific surface areas of the as-prepared samples through the nitrogen adsorption−desorption isotherms at 77 K. XPS characterization was conducted with the ESCALAB 250 photoelectron spectroscope system by using Al Kα radiation. For the characterization of RhB/BiOCl, the samples were prepared as follows: 20 mg of the sample was dispersed into 50 mL of 20 mg/L RhB aqueous solution and stirred constantly for 1 h under dark conditions to establish an adsorption−desorption equilibrium, then filtered, and dried at 50 °C for 12 h. Photocatalytic Measurements. The photocatalytic activity experiments of samples were evaluated by photodegrading the Rhodamine B (RhB) under visible light irradiation at ambient temperature using a 300 W Xe arc lamp (CEL-HXF300, Beijing) with a cutoff filter (λ > 420 nm). Briefly, a 0.02 g photocatalyst was added into 100 mL of aqueous solution containing 40 mg/L RhB solution. Prior to irradiation, the suspension was magnetically stirred

EXPERIMENTAL SECTION

Materials. Bismuth nitrate pentahydrate (Bi(NO3)3·5H2O), poly(vinyl alcohol) (PVA), sodium chloride (NaCl), ethylene glycol (EG), acetic acid (98%) (AC), nitric acid (36%), sulfuric acid (98%), sodium hydroxide (NaOH), ammonium hydroxide (25%), anhydrous ethanol, 4620


Research Article


Figure 2. SEM images of BiOCl samples prepared in different solutions: (a) HNO3/ethanol, (b) H2O/ethanol, (c) AC/ethanol, (d) EG/ethanol, and (e) NH4OH/ethanol.

Table 1. Physical Parameter and Photosensitization Degradation Activity of the BiOCl Samples solvent

Ha (nm)

Lb (nm)

SBET (m2 g−1)

Kc (10−2 min−1)

Kd (10−4 g min−1 m−2)

HNO3 H2O AC EG NH4OH

250 61.5 50.6 27.5 15

3030 523.7 454.8 139.4 123.8

17.302 10.16 9.2047 32.86 63.82

0.1 1.2 1.3 3.3 9.6

0.578 11.81 14.12 10.04 15.04

a Approximate thickness (nm). bDiameter of BiOCl samples from TEM images (nm). cThe degradation rate constant of RhB. dNormalized degradation rate constant of RhB.

■

in the dark for 1 h to ensure desorption−adsorption equilibrium. During the procedure of degradation, the analytical samples (about 4 mL) were taken every 5 min and centrifugated at a rate of 8000 rpm to remove the remaining particles. In addition, the RhB concentration was monitored by recording the absorbance of supernatants at maximum absorption wavelength using a UV−vis spectrophotometer (Shimadzu 2550, Japan). Photoelectrochemical Measurements. The photocurrent characterization and electrochemical impedance spectroscopy were carried out on the three electrode quartz cell by the CHI660D workstation. The BiOCl/FTO conductor glass, Ag/AgCl electrode, and platinum foil plate were used as the working electrode, reference electrode, and counter electrode, respectively. The photoanodes were prepared according to a previously reported method.28,29 The FTO substrates were cleaned by ultrasonication in acetone, absolute ethanol, and distilled water for 30 min, respectively. Then, a 10 mg powder sample was dispersed into 100 μL of 25% (W/V) PVA solution under ultrasonication for 1 h to obtain slurries. Afterwards, the as-prepared slurries were spread on FTO substrates, whose edge parts were preprotected by transparent adhesive tape of the size 1 cm × 1 cm. These as-prepared FTO glass electrodes were fired at 80 °C for 12 h. The current density−voltage (J−V) and the current−power (J−JV) characteristic were investigated to display the photoelectric performance of BiOCl photoanodes. A 300 W Xe arc lamp (CEL-HXF300, Beijing) was utilized as a light source with a cutoff filter (λ > 420 nm). Na2SO4 (0.05 mol/L) aqueous solution was used as the supporting electrolyte. The initial pH of the solution was adjusted to 2.0 by adding 1 M H2SO4. Prior to irradiation, the photoanode was vertically inserted in dye solution with stirring continuously in the dark for 30 min to absorb the dye molecules.

RESULTS AND DISCUSSION

The characterization of XRD patterns was carried out to describe the crystal structure of samples. From Figure 1a, all of the diffraction patterns corresponded to the BiOCl tetragonal crystals (JCPDS 06-0249), and no other diffraction peaks were observed. However, the samples prepared in different solvents exhibited distinct differences of diffraction peak intensity on {001} and {010} facets. Compared to the other solvent, the sample obtained in HNO3/ethanol possessed the highest (001) peaks which were the characteristic diffraction peaks of {001} facets. Because the hydrogen ions in solution preferred to absorb on oxygen terminated {001} facets; therefore, the BiOCl with {001} facets was easily formed under high [H+] condition.18 Once the [H+] in solution was controlled by using a different solvent, the intensity of (001) peaks became weak gradually, indicating that the growth rate of BiOCl was decayed along the {001} facet direction.30 Furthermore, the (110) peaks, as characteristic diffraction peaks of {010} facets, grew rapidly. For reducing the surface energy and promoting the growth of highly active {010} facets, the thickness of BiOCl became thin, and the areas of {001} also decreased. As clearly shown in Figure 1b, it could be seen that the specific values of the I(110)/I(001) gradually increased with the decrease of {001}. These results suggested that the crystal growth speed was inhibited along the {001} facets and increased along the {010} facets as a result of the preferred orientation under the low [H+]. Different surface properties endow semiconductors with distinctive optical and electronic properties.31,32 The BiOCl with a large percentage area of {010} facets exposed 4621


Research Article


Figure 3. TEM and HR-TEM images of BiOCl samples prepared in different solvent: (a, b) HNO3/ethanol, (c) H2O/ethanol, (d) AC/ethanol, (e) EG/ethanol, and (f, g) NH4OH/ethanol.

nanodiscs were much thinner and smaller than a nanosheet (Figure 2b). Compared to those of the H2O/ethanol samples, the size and thickness of BiOCl prepared in CH3COOH/ ethanol became slightly smaller owing to the low degree of ionization of CH3COOH. In EG/ethanol solution, Bi3+ preferred to absorb on oxygen terminated EG molecule to form a relatively stable complex Bi2(OCH2CH2O)3. Relatively speaking, the stronger dissolving capacity between EG and ethanol solution is beneficial for the formation and growth of BiOCl tiny nuclei. Moreover, the tiny nuclei are not easy to reunite together in ethanol solution during the growth, leading to the final products with small crystal size (Figure 2d). These results corresponded to those from the literature reports.33,34 Finally, the 3D porous nanoflower structure of BiOCl was formed through the Ostwald ripening and self-assembly process.35,36 With a further decrease of [H+], the BiOCl ultrathin nanosheet units were formed in NH4OH/ethanol solution first owing to the growth of {010} facets, and then the ultrathin nanosheets aggregated freely into a 3D porous

exhibited superior dye photosensitization activity under visible light.18,19 The typical scanning electron microscopy (SEM) images of BiOCl samples were shown in Figure 2. With the growth of {010} faces, the size of BiOCl samples gradually decreased, and the nanostructures changed from the 2D nanosheet to the 3D nanoflower (Figure 2a−e). This change was ascribed to the change of [H+] in ethanol solution. All detailed parameters are displayed in Table 1. During the growth of BiOCl, the hydrogen ions in solution preferred to absorb on oxygen terminated {001} facets and increased the crystal growth speed along the ab plane. Therefore, the uniform square-shaped BiOCl nanosheets with exposed {001} were obtained in a HNO3/ethanol solution. Once H2O was used as solvent, the hydrogen ions mainly came from the hydrolysis of Bi(NO3)3, and therefore, the [H+] was much lower than HNO3 solution which resulted in the slow crystal growth along the ab plane. It was clearly observed that the morphology of BiOCl changed from a uniform nanosheet to nanodiscs. Also, the BiOCl 4622


Research Article


Figure 4. XPS spectra of BiOCl samples: (a) survey, (b) Bi4f, (c) O1s.

defect on the surface of BiOCl would be changed from VBi‴ to VBi‴VO••VBi‴ with the decrease of thickness. The negatively charged VBi‴VO••VBi‴ preferred to absorb molecular cationic dye.38 Clear and continuous lattice fringes with a lattice spacing of 0.37 nm were determined by high-resolution TEM (HRTEM) images (Figure 3g), that corresponded to the {002} atomic planes. The physical and chemical performance of semiconductor materials is closely related to its surface properties and geometric structure. The XPS characterization was carried out to record the surface chemical properties and composition of as-prepared BiOCl. As shown in Figure 4a, bismuth, oxygen, and chloride elements were included in the sample. The elements’ molar ratio was estimated to be 1:1.42:0.93 corresponding with the stoichiometric molar ratio in BiOCl. The peaks of binding energies for the Bi(4f) core level were located at 164.78 and 159.48 eV, which belonged to Bi(4f5/2) and Bi(4f7/2), respectively (Figure 4b). Also, the positions of characteristic peaks were the same in BiOCl-HNO3 and BiOCl-NH4OH. These results suggested that the bismuth ions in BiOCl samples were in a trivalence chemical state. The binding energies of O1s in different BiOCl samples were presented in Figure 4c. It could be clearly seen that the O1s peak position in BiOClNH4OH had a slight shift (0.31 eV) along low binding energy orientation. This suggested that the BiOCl-NH4OH surface had more negative charge than BiOCl-HNO3, which could be attributed to the decrease of the BiOCl thickness. With the

nanoflower to reduce the surface energy (Figure 2e). The nanoflower structure with interlaced ultrathin nanosheets can not only greatly increase the surface areas of photocatalyst, but also enhance the multireflection of light.37 The decrease of size and the change of structure can influence significantly the physical and chemical properties of BiOCl. More details about the crystal structure and morphology of BiOCl were obtained from the transmission electron microscopy (TEM) images. The square-shaped BiOCl nanosheet structure was acquired in HNO3/ethanol, with diameter and thickness 3 and 0.25 μm (Figure 3a). A clear lattice spacing of 0.275 nm and the interfacial angle of 90° were observed (Figure 3b), which corresponded to the (110) lattice planes. When the [H+] was controlled, the size of BiOCl became small, and the morphology changed to nanodiscs. The thicknesses of samples were estimated to be 61.5, 50.6, and 27.5 nm by using H2O, CH3COOH, and (CH2OH)2 as solvent, respectively (Figure 3c−e). Also, the nanoflower structure of BiOCl was presented in Figure 3f. It was clearly observed that the BiOCl nanoflower was composed of a large amount of interlaced ultrathin nanosheets with 15 nm thickness. As mentioned previously, the solvents have a significant effect on the morphology and thickness of BiOCl samples. The surface areas of BiOCl can be enlarged greatly owing to the reduction of nanosized species and the formation of a nanoflower structure, which can provide a larger space for dye molecule absorption and chemical reaction. Moreover, the predominant 4623


Research Article


Figure 5. (a) Nitrogen adsorption−desorption isotherm of BiOCl samples prepared in different solvents (b) and the absorption curve of RhB by BiOCl samples.

Figure 6. (a) UV−vis DRS of BiOCl samples prepared in different solvent, and (b) plots of (αhν)1/2 versus photon energy (hν) for the BiOCl.

growth of {010}, the thickness of BiOCl decreased gradually, leading to the change of predominant defects on the surface of BiOCl from VBi‴ to VBi‴VO••VBi‴. The negative charge of VBi‴VO••VBi‴ defects is favorable for cationic dye absorption.38 The nitrogen adsorption−desorption isotherm analysis was conducted to survey the special surface area of BiOCl samples. With the growth of {010} facets, the surface areas of BiOCl reduced first and then increased, which was attributed to the change in its nanostructure (Figure 5a). The large special surface area can offer more active sites and open space for molecular dye absorption. The BiOCl prepared in NH4OH/ ethanol solution possessed the largest surface area than the others due to its 3D interlaced nanoflower structure. All of these detailed parameters are displayed in Table 1. The RhB adsorption curves over the as-prepared samples under dark conditions for 60 min were shown in Figure 5b. As light receptors and electron donor, the adsorption efficiency of photosensitizer is an important influencing factor on the generation of photoelectrons and light-harvesting. In comparison, the RhB adsorption capability of BiOCl-NH4OH is larger than that of the others, which is primarily ascribed to its large surface area and thin nanosheet structure. Although the BiOCl prepared in HNO3 had a relatively large surface area (17.302 m2 g−1), the RhB adsorption capability was lower than that of the others, revealing that the physical performance of BiOCl was closely related with {010} facets. The {010} facets could provide more active sites for cationic RhB molecule absorption. For DSPFCs, the large special surface areas play a vital role in enhancing the harvest of visible light and dye absorption capability.39

The DRS was employed to analyze the optical absorption properties of the BiOCl samples as shown in Figure 6a. Generally, the energy gap of a photocatalyst directly determines its optical absorption performance. This is the conversion formula40 αhν = A(hν − Eg )1/2

(1)

where α, h, ν, and Eg are the absorption constant, Planck constant, light frequency, and band gap, respectively. Therefore, the band gaps of BiOCl and BiOCl-RhB were estimated to be 3.25 and 3.12 eV (Figure 6b). For the wide band gap, the BiOCl samples had no visible light absorption range from 400 to 800 nm. Once the dye molecule was adsorbed on the surface of BiOCl, its absorption intensity for visible light improved significantly. Moreover, the band gap of BiOCl/RhB samples was slightly smaller than that of BiOCl. The reasons that the visible light absorption capacity of BiOCl/RhB improved and its band gap became slightly more narrow were primarily attributed to the dye photosensitization performance of BiOCl{010} and the defective energy levels. On one hand, the RhB molecules adsorbed on the {010} surface by the dye self-photosensitization process can greatly enhance the visible light absorption due to the narrow band gap of RhB (Eg = 2.37 eV).41 On the other hand, the thickness of BiOCl reduced with the growth of {010} activity facets, which resulted in the change of the predominant defect on the surface of BiOCl from VBi‴ to VBi‴VO••VBi‴. The existence of oxygen vacancy defects could induce a new energy level to form within the forbidden band of BiOCl and RhB. The new energy level would decrease the band 4624


Research Article


Figure 7. Photocatalytic performance of BiOCl samples prepared in different solvents under visible light irradiation: (a) the degradation curve of RhB over BiOCl samples, (b) the reaction rate constant and the normalized degradation rate constant of RhB, (c) the effect of pH for RhB photosensitization degradation, (d) the UV−vis absorption spectra and photographic image of RhB photosensitization degradation.

(SHE).47,48 It was surprising to find that the 100 mL of the 40 mg/L RhB solution decomposed completely after 25 min under visible light irradiation when 20 mg of the BiOCl photocatalyt prepared in the NH4OH/ethanol solution was used. In order to accurately describe the photocatalytic performance, the initial reaction rate of photocatalytic degradation was investigated. From Figure 7b, it was clearly seen that the reaction rate constant (k) and that normalized by the surface area (k′) on RhB photosensitization degradation were closely related to the area of {010} facets. These detailed data are displayed in Table 1. The effects of pH on the RhB adsorption and photosensitization degradation are shown in Figure 7c. With the increase of pH, the RhB adsorption was decreased after continuous stirring for 60 min. Moreover, the RhB photosensitization degradation efficiency had no obvious distinction in the pH variation from 2.0 to 6.0, but it decreased quickly when the pH changed to 10.0. Because the RhB molecules preferred to aggregate with each other to form a larger molecule with the increased pH value, and these large molecules were hardly absorbed on the surface of BiOCl{010} facets, the RhB photosensitization degradation efficiency decrease was sharp.49 In conclusion, the dye photosensitization degradation efficiency would be enhanced at pH = 2.0 and hindered at a higher pH value. The RhB characteristic absorption peak centered at 553 nm decreased quickly with the extension of visible light irradiation time, and the color removal reached up to 100% after 25 min (Figure 7d). The XRD and XPS before and after light irradiation had also been conducted to elucidate the stability of photocatalyst. As shown in Figure S3 (Supporting Information), there was no significant change in the data of XRD and XPS, which suggested the as-prepared BiOCl photocatalyst was stable. The excellent dye photosensitization degradation performance

gap of BiOCl/RhB.38,42−44 From Figure 6a, it was clearly seen that the visible light absorption intensity of BiOCl enhanced gradually with the growth of {010} facets. That was because the {010} facets could provide large surface area and more active sites for RhB absorption, which was favorable for the enhancement of visible light absorption. The results can be proven by the SEM image of RhB/BiOCl in Figure S1 (Supporting Information). The peak at 567 nm was the absorbance of RhB. These results have indicated that the visible light absorption of BiOCl can be enhanced by controlling the growth of {010} facets. The high harvest of visible light is beneficial for improving the photovoltaic performance of DSPFCs.45 The photocatalytic performance of BiOCl{010} was evaluated by RhB photosensitization degradation under visible light. From Figure 7a, it could be clearly observed that the RhB photosensitization degradation efficiency significantly improved with the growth of {010} facets. Obviously, the BiOCl with large areas of {010} facets possessed strong dye absorption capability, which can greatly enhance the light-harvesting. The large amounts of photoelectrons could be directly injected from the excited dye molecule into the conduction band of BiOCl and were captured by dissolved O2.46 Owing to the more negative BiOCl conduction band (−1.1 eV) than [E(O2/O2•−) (−0.046 eV)], the photoelectrons were more easily transferred to the BiOCl conduction band. Thus, the O2•− oxidation activity species could be generated for dye decomposition. The Mott−Schottky plot for BiOCl-NH4OH had been conducted to elucidate its semiconductor properties. As shown in Figure S2 (Supporting Information), the flat band potential (Vfb) of BiOCl-NH4OH was approximately determined to be −1.26 V versus Ag/AgCl. That is to say, the conduction band of BiOClNH4OH is around −1.1 V versus standard hydrogen electrode 4625


Research Article


the {010} facets. Therefore, the large areas of {010} facets exposed would be favorable for photoelectron transfer.18 Moreover, the size and thinness of BiOCl also decrease with the growth of {010} facets, leading to the decrease of the photoelectron diffusion distance. Compared to BiOCl-NH4OH, the resistance of P25 was much larger owing to the presence of surface states on the TiO2 surface. The surface states would greatly restrict the photoelectron diffusion.50 Therefore, owing to the sufficient dye adsorption and the open channel property of {010} facets, BiOCl with large area of {010} facets exhibited higher photocurrent. The characterization of current−voltage (J−V) and current− power (J−JV) was obtained to further survey the photovoltaic performance of BiOCl in dye self-photosensitization photocatalytic fuel cells (DSPFCs). In the DSPFC system, the BiOCl photoanode used the molecular dye as fuel to generate electrons under visible light irradiation. The electron could be spontaneously transferred through an external circuit from photoanode to cathode to generate electricity.51,52 Therefore, the high photoelectric conversion efficiency could be obtained when massive photoelectrons were generated and transferred effectively on the surface of the photoanode. The short-circuit current density (Jsc), the open-circuit potential (Voc), and fill factor (FF) of the cell with different BiOCl photoanodes are

indicates that the BiOCl with large percentage of {010} areas could be a promising material for DSPFCs. The transient photocurrent responses were employed to analyze the formation and transfer of photoelectrons on the surface of BiOCl. As displayed in Figure 8, there had been no

Figure 8. Transient photocurrent responses of BiOCl samples in 0.05 M Na2SO4 aqueous solutions under visible light.

photocurrent generation under visible light irradiation on the BiOCl/FTO electrode. Because of its high light excitation energy, the photoinduced charge carriers failed to be generated on the surface of BiOCl. However, a high photocurrent signal appeared under visible light after the BiOCl/FTO electrode was inserted into RhB solution for 30 min, which suggested that a large number of electrons were generated and transferred on the surface of the electrodes. Moreover, as the larger {010} facets were exposed, the higher photocurrent was generated on the surface of BiOCl. The {010} facets can offer a large surface area and more active sites for RhB molecule adsorption which is beneficial for the formation of photoelectrons. In order to further prove that the {010} facets were vital to the photosensitization property, BiOCl samples with a large surface area and nearly 100% exposed {001} facets were prepared.27 Figure S4 in Supporting Information showed the comparison of transient photocurrent responses of BiOCl-001 and BiOClNH4OH. It could be clearly seen that a higher transient photocurrent was generated on the BiOCl-NH4OH photoanode than on BiOCl-001 when the BiOCl-NH4OH samples possessed similar surface areas to that of BiOCl-001. This was primarily attributed to the more active sites and the open channel performance of {010} facets. On one hand, the {010} facets could provide more active sites for RhB molecule adsorption. Therefore, more photoelectrons could be offered by excited RhB molecules under visible light. On the other hand, the open channel performance of the {010} facet was a benefit for photoelectron transfer. Therefore, the growth of {010} facets greatly enhanced the photoelectric property of BiOCl. Electrochemical impedance spectroscopy (EIS) can be carried out to survey the photoelectron transfer on the surface of the electrode. The high resistance will raise the loss of photoelectrons, and then affect the electricity generation efficiency and photocatalytic activity in DSPFCs. From Figure S5 in Supporting Information, the resistance of BiOCl photoanodes decreased with the increase of {010} facets, which was attributed to the open channel property of {010}. In BiOCl, the internal electric fields could be induced to form due to its unique layered structure, and the electric fields were parallel to

Table 2. Current−Voltage Characteristics of the BiOCl-Pt Cell with Different BiOCl Photoanodes under Visible Light Irradiationa

a

solvent

Jsc (mA/cm2)

Voc (V)

FF

no fuel P25 HNO3 H2O AC EG NH4OH BiOCl{001}

0.0012 0.0025 0.0017 0.0033 0.0036 0.0049 0.0058 0.0038

0.309 0.152 0.309 0.493 0.57 0.634 0.689 0.297

0.110 0.21 0.112 0.084 0.096 0.096 0.11 0.224

CRhB = 10 mg/L, Na2SO4 0.05 mol/L, pH 2.0.

displayed in Table 2. The fill factor was determined by the following formula:53 FF =

Pmax I × Vmax = max Jsc × Voc Jsc × Voc

(2)

Here, ImaxVmax is the maximum power of the BiOCl-Pt cell obtained from the current−power curve. JscVoc is the highest possible maximum power of the cell. The fill factor, that directly reflects the performance of fuel cell, is denoted by the specific value of the maximum power and the highest possible maximum power of the cell. In DSPFCs, the Jsc was 0.0012 mA cm−2 with the absence of RhB and increased from 0.0017 to 0.0033, 0.0041, 0.0049, and 0.0058 mA cm−2 with the growth of {010} facets (Figure 9a). The increase of Jsc was primarily attributed to the {010} facets that provided large surface areas for RhB adsorption and an open channel for photoelectron transfer. The photovoltaic performance comparison of DSPFCs assembled with BiOCl-NH4OH, BiOCl{001}, and P25 photoanodes, respectively, was carried out (Figure S6 in Supporting Information). It could be clearly observed that a higher photocurrent was generated on the BiOCl-NH4OH 4626


Research Article


visible light irradiation after four consecutive cycles. Exploiting excellent photosensitization performance materials, that utilize contaminant as fuel and solar energy as impetus to generate electricity, has an important meaning for the sustainable development of environment and energy.54 The BiOCl with large areas of {010} facets and interlaced ultrathin structure exhibited excellent photocatalytic activity and photoelectric performance. Therefore, our study will open an avenue for the wide application of BiOCl in environment protection and energy.

■

CONCLUSION In conclusion, BiOCl materials with tunable exposed {010} facets were successfully synthesized by using different solvents. The growth of {010} facets was controlled by the [H+] in the solution. The sample prepared in NH4OH solution possessed the largest area of {010} facets and surface area among these samples. For a decrease in the surface energy to support the growth of highly active {010} facets, the thickness of BiOCl was reduced and the structure changed from nanoplates to nanoflowers. The photosensitization degradation activity of RhB enhanced with the growth of {010} facets, which was attributed to the large surface area and open channel performance of {010} facets. The excellent photovoltaic performance was obtained on the BiOCl-NH4OH photoanode by employing RhB as fuel whose Jsc and Voc were 0.0058 mA/ cm2 and 0.689 V, respectively. Meanwhile, approximately 67% color removal efficiency was achieved on the BiOCl{010}-Pt cell by treating 40 mL of 5 mg/L RhB under visible light for 240 min, which was much higher than P25-Pt (4%). Moreover, the DSPFCs still exhibited high photocatalytic activity after four consecutive cycles. For all we know, this strategy that investigates the effect of different crystal structures on chemical properties is also appropriate for other semiconductor materials, such as TiO2 and Ag3PO4, which is beneficial for promoting the development of PFCs and DSPFCs. We expect our work to open a new avenue for the wide application of BiOCl in environment protection and energy, and provide new ideas on exploitation and synthesis of photoanode materials for high-performance DSPFCs.

Figure 9. Current−voltage (J−V) plots and power−voltage (J−JV) plots for a BiOCl-Pt cell with different BiOCl photoanodes under visible light irradiation. CRhB = 10 mg/L, 0.05 M Na2SO4 aqueous solutions, pH = 2.0.

photoanode than on BiOCl{001} and P25 owing to the excellent dye absorption capability and photoelectron transfer efficiency of the {010} facets. The characteristic of current− power (J−JV) based DSPFCs was assessed to evaluate the performance of the output power of the cell, as shown in Figure 9b. The BiOCl with the largest {010} areas exposed possessed high output power. For the DSPFC system, the photoelectrons generated from RhB molecules were transferred to the cathode through an external circuit and reacted with dissolved O2 in solution to form the O2•− oxidizing species, and then further to oxidize pollutant, which achieved the process of energy recovery and dye decomposition (Figure S7 in Supporting Information). The RhB degradation efficiencies with different BiOCl samples on DSPFC were investigated. As shown in Figure S8 (Supporting Information), the RhB degradation efficiency enhanced with the growth of {010} facets. Also, 67% RhB color removal efficiency was obtained on a BiOCl(NH4OH)-Pt cell by treating 40 mL of 5 mg/L RhB under visible light for 240 min, which much higher than P25-Pt (4%). These results indicate that the BiOCl exhibits higher photoelectric and photocatalytic performance than TiO2 owing to its large areas of {010} facets. In order to elucidate the recyclability performance of BiOCl-NH4OH in photocatalytic fuel cells, the recycling experiment has been carried out. As shown in Figure S9 (Supporting Information), the BiOCl-NH4OH photoanode still possessed an excellent photocatalytic performance under

■

ASSOCIATED CONTENT

S Supporting Information *

The Supporting Information is available free of charge on the ACS Publications website at DOI: 10.1021/acssuschemeng.6b03150. Additional characterization data (PDF)

■

AUTHOR INFORMATION

Corresponding Authors

*Phone: +86 731 88823820. E-mail: [email protected]. *E-mail: [email protected]. ORCID

Cheng-Gang Niu: 0000-0002-2530-4858 Notes

The authors declare no competing financial interest.

■

ACKNOWLEDGMENTS This work was financially supported by the National Natural Science Foundation of China (51541801, 51521006), the Hunan Provincial Natural Science Foundation of China 4627


Research Article


(19) Hu, J.; Fan, W.; Ye, W.; Huang, C.; Qiu, X. Insights into the photosensitivity activity of BiOCl under visible light irradiation. Appl. Catal., B 2014, 158, 182−189. (20) Zhang, K. L.; Liu, C. M.; Huang, F. Q.; Zheng, C.; Wang, W. D. Study of the electronic structure and photocatalytic activity of the BiOCl photocatalyst. Appl. Catal., B 2006, 68, 125−129. (21) Shamaila, S.; Sajjad, A. K. L.; Chen, F.; Zhang, J. WO3/BiOCl, a novel heterojunction as visible light photocatalyst. J. Colloid Interface Sci. 2011, 356, 465−472. (22) Dong, F.; Sun, Y.; Fu, M.; Wu, Z.; Lee, S. C. Room temperature synthesis and highly enhanced visible light photocatalytic activity of porous BiOI/BiOCl composites nanoplates microflowers. J. Hazard. Mater. 2012, 219, 26−34. (23) Zhu, G.; Hojamberdiev, M.; Tan, C.; Jin, L.; Xu, C.; Liu, Y.; Zhou, J.; Liu, P. Photodegradation of organic dyes with anatase TiO2 nanoparticles-loaded BiOCl nanosheets with exposed {001} facets under simulated solar light. Mater. Chem. Phys. 2014, 147, 1146−1156. (24) Chen, C.; Ma, W.; Zhao, J. Semiconductor-mediated photodegradation of pollutants under visible-light irradiation. Chem. Soc. Rev. 2010, 39, 4206−4219. (25) Bi, Y.; Ouyang, S.; Umezawa, N.; Cao, J.; Ye, J. Facet effect of single-crystalline Ag3PO4 sub-microcrystals on photocatalytic properties. J. Am. Chem. Soc. 2011, 133, 6490−6492. (26) Yang, H. G.; Sun, C. H.; Qiao, S. Z.; Zou, J.; Liu, G.; Smith, S. C.; Lu, G. Q.; Cheng, H. M. Anatase TiO2 single crystals with a large percentage of reactive facets. Nature 2008, 453, 638−641. (27) Wang, D. H.; Gao, G. Q.; Zhang, Y. W.; Zhou, L. S.; Xu, A. W.; Chen, W. Nanosheet-constructed porous BiOCl with dominant {001} facets for superior photosensitized degradation. Nanoscale 2012, 4, 7780−7785. (28) He, H.; Berglund, S. P.; Xiao, P.; Chemelewski, W. D.; Zhang, Y.; Mullins, C. B. Nanostructured Bi2S3/WO3 heterojunction films exhibiting enhanced photoelectron chemical performance. J. Mater. Chem. A 2013, 1, 12826−12834. (29) Zhang, Y. J.; Mori, T.; Ye, J.; Antonietti, M. Phosphorus-doped carbon nitride solid: enhanced electrical conductivity and photocurrent generation. J. Am. Chem. Soc. 2010, 132, 6294−6295. (30) Fang, W. Q.; Zhou, J. Z.; Liu, J.; Chen, Z. G.; Yang, C.; Sun, C. H.; Yang, H. G.; et al. Hierarchical structures of single-crystalline anatase TiO2 nanosheets dominated by {001} facets. Chem. - Eur. J. 2011, 17, 1423−1427. (31) Liu, M.; Piao, L.; Zhao, L.; Ju, S.; Yan, Z.; He, T.; Wang, W.; Zhou, C. Anatase TiO2 single crystals with exposed {001} and {110} facets: Facile synthesis and enhanced photocatalysis. Chem. Commun. 2010, 46, 1664−1666. (32) Zhang, B.; Wei, F.; Wu, Q.; Piao, L.; Liu, M.; Jin, Z. Formation and evolution of the high-surface-energy facets of anatase TiO2. J. Phys. Chem. C 2015, 119, 6094−6100. (33) Wang, Y.; Li, S.; Xing, X.; Huang, F.; Shen, Y.; Xie, A.; Zhang, J.; Wang, X. Self-assembled 3D flowerlike hierarchical Fe3O4@Bi2O3 core-shell architectures and their enhanced photocatalytic activity under visible light. Chem. - Eur. J. 2011, 17, 4802−4808. (34) Zhu, L. P.; Liao, G. H.; Bing, N. C.; Wang, L. L.; Yang, Y.; Xie, H. Y. Self-assembled 3D BiOCl hierarchitectures: tunable synthesis and characterization. CrystEngComm 2010, 12, 3791−3796. (35) Zhang, Z.; Wang, Z.; He, S.; Wang, C.; Jin, M.; Yin, Y. Redox reaction induced Ostwald ripening for size-and shape-focusing of palladium nanocrystals. Chemical Science 2015, 6, 5197−5203. (36) Ding, L.; Wei, R.; Chen, H.; Hu, J.; Li, J. Controllable synthesis of highly active BiOCl hierarchical microsphere self-assembled by nanosheets with tunable thickness. Appl. Catal., B 2015, 172, 91−99. (37) Mi, Y.; Wen, L.; Wang, Z.; Cao, D.; Fang, Y.; Lei, Y. Building of anti-restack 3D BiOCl hierarchitecture by ultrathin nanosheets towards enhanced photocatalytic activity. Appl. Catal., B 2015, 176, 331−337. (38) Guan, M.; Xiao, C.; Zhang, J.; Fan, S.; An, R.; Cheng, Q.; Xie, Y.; et al. Vacancy associates promoting solar-driven photocatalytic activity of ultrathin bismuth oxychloride nanosheets. J. Am. Chem. Soc. 2013, 135, 10411−10417.

(14JJ2045), and a Project Supported by Scientific Research Fund of Hunan Provincial Education Department (13k017).

■

REFERENCES

(1) Fujishima, A. Electrochemical photolysis of water at a semiconductor electrode. Nature 1972, 238, 37−38. (2) Lianos, P. Production of electricity and hydrogen by photocatalytic degradation of organic wastes in a photoelectrochemical cell: the concept of the Photo fuel cell: A review of a re-emerging research field. J. Hazard. Mater. 2011, 185, 575−590. (3) Li, K.; Zhang, H.; Tang, T.; Xu, Y.; Ying, D.; Wang, Y.; Jia, J. Optimization and application of TiO2/Ti−Pt photo fuel cell (PFC) to effectively generate electricity and degrade organic pollutants simultaneously. Water Res. 2014, 62, 1−10. (4) Chen, Q.; Li, J.; Li, X.; Huang, K.; Zhou, B.; Cai, W.; Shangguan, W. Visible-light responsive photocatalytic fuel cell based on WO3/W photoanode and Cu2O/Cu photocathode for simultaneous wastewater treatment and electricity generation. Environ. Sci. Technol. 2012, 46, 11451−11458. (5) Liu, Y.; Li, J.; Zhou, B.; Lv, S.; Li, X.; Chen, H.; Cai, W.; Chen, Q. Photoelectrocatalytic degradation of refractory organic compounds enhanced by a photocatalytic fuel cell. Appl. Catal., B 2012, 111, 485− 491. (6) Li, J.; Li, J.; Chen, Q.; Bai, J.; Zhou, B. Converting hazardous organics into clean energy using a solar responsive dual photoelectrode photocatalytic fuel cell. J. Hazard. Mater. 2013, 262, 304−310. (7) Liu, Y.; Li, J.; Zhou, B.; Chen, H.; Wang, Z.; Cai, W. A TiO2nanotube-array-based photocatalytic fuel cell using refractory organic compounds as substrates for electricity generation. Chem. Commun. 2011, 47, 10314−10316. (8) Wang, B.; Zhang, H.; Lu, X. Y.; Xuan, J.; Leung, M. K. Solar photocatalytic fuel cell using CdS-TiO2 photoanode and air-breathing cathode for wastewater treatment and simultaneous electricity production. Chem. Eng. J. 2014, 253, 174−182. (9) Kopidakis, N.; Benkstein, K. D.; van de Lagemaat, J.; Frank, A. J.; Yuan, Q.; Schiff, E. A. Temperature dependence of the electron diffusion coefficient in electrolyte-filled TiO2 nanoparticle films: evidence against multiple trapping in exponential conduction-band tails. Phys. Rev. B: Condens. Matter Mater. Phys. 2006, 73, 045326. (10) Mor, G. K.; Kim, S.; Paulose, M.; Varghese, O. K.; Shankar, K.; Basham, J.; Grimes, C. A. Visible to near-infrared light harvesting in TiO2 nanotube array-P3HT based heterojunction solar cells. Nano Lett. 2009, 9, 4250−4257. (11) Antoniadou, M.; Sfaelou, S.; Lianos, P. Quantum dot sensitized titania for photo-fuel-cell and for water splitting operation in the presence of sacrificial agents. Chem. Eng. J. 2014, 254, 245−251. (12) Antoniadou, M.; Kondarides, D. I.; Dionysiou, D. D.; Lianos, P. Quantum dot sensitized titania applicable as photoanode in photoactivated fuel cells. J. Phys. Chem. C 2012, 116, 16901−16909. (13) Hardman, R. A toxicologic review of quantum dots: toxicity depends on physicochemical and environmental factors. Environ. Sci. Technol. 2006, 114, 165−172. (14) Davis, A. P.; Huang, C. P. The photocatalytic oxidation of sulfur-containing organic compounds using cadmium sulfide and the effect on CdS photocorrosion. Water Res. 1991, 25, 1273−1278. (15) Li, K.; Tang, Y.; Xu, Y.; Wang, Y.; Huo, Y.; Li, H.; Jia, J. A BiOCl film synthesis from Bi2O3 film and its UV and visible light photocatalytic activity. Appl. Catal., B 2013, 140, 179−188. (16) Li, K.; Xu, Y.; He, Y.; Yang, C.; Wang, Y.; Jia, J. Photocatalytic fuel cell (PFC) and dye self-photosensitization photocatalytic fuel cell (DSPFC) with BiOCl/Ti photoanode under UV and visible light irradiation. Environ. Sci. Technol. 2013, 47, 3490−3497. (17) Fabian, J.; Nakazumi, H.; Matsuoka, M. Near-infrared absorbing dyes. Chem. Rev. 1992, 92, 1197−1226. (18) Jiang, J.; Zhao, K.; Xiao, X.; Zhang, L. Synthesis and facetdependent photoreactivity of BiOCl single-crystalline nanosheets. J. Am. Chem. Soc. 2012, 134, 4473−4476. 4628


Research Article

ACS Sustainable Chemistry & Engineering (39) Li, Y.; Kunitake, T.; Fujikawa, S. Efficient fabrication and enhanced photocatalytic activities of 3D-ordered films of titania hollow spheres. J. Phys. Chem. B 2006, 110, 13000−13004. (40) Zhu, G.; Hojamberdiev, M.; Katsumata, K. I.; Matsushita, N.; Okada, K.; Liu, P.; Liu, Y.; Zhou, J. Synthesis of heterostructured In2O3/BiOCl powders and their visible-light-driven photocatalytic activity for the degradation of Rhodamine B. Adv. Powder Technol. 2014, 25, 1292−1303. (41) Zhang, L. L.; Xiong, Z.; Zhao, X. S. Pillaring chemically exfoliated graphene oxide with carbon nanotubes for photocatalytic degradation of dyes under visible light irradiation. ACS Nano 2010, 4, 7030−7036. (42) Pan, J.; Liu, G.; Lu, G. Q. M.; Cheng, H. M. On the true photoreactivity order of {001}, {010}, and {101} facets of anatase TiO2 crystals. Angew. Chem., Int. Ed. 2011, 50, 2133−2137. (43) Xie, T.; Xu, L.; Liu, C.; Yang, J.; Wang, M. Magnetic composite BiOCl-SrFe12O19: a novel p-n type heterojunction with enhanced photocatalytic activity. Dalton Transactions 2014, 43, 2211−2220. (44) Sun, M.; Zhao, Q.; Du, C.; Liu, Z. Enhanced visible light photocatalytic activity in BiOCl/SnO2: heterojunction of two wide band-gap semiconductors. RSC Adv. 2015, 5, 22740−22752. (45) Kim, S.; Choi, W. Visible-light-induced photocatalytic degradation of 4-chlorophenol and phenolic compounds in aqueous suspension of pure titania: demonstrating the existence of a surfacecomplex-mediated path. J. Phys. Chem. B 2005, 109, 5143−5149. (46) Tan, C.; Zhu, G.; Hojamberdiev, M.; Okada, K.; Liang, J.; Luo, X.; Liu, Y.; Liu, Y. Co3O4 nanoparticles-loaded BiOCl nanoplates with the dominant {001} facets: efficient photodegradation of organic dyes under visible light. Appl. Catal., B 2014, 152, 425−436. (47) Weng, S.; Chen, B.; Xie, L.; Zheng, Z.; Liu, P. Facile in situ synthesis of a Bi/BiOCl nanocomposite with high photocatalytic activity. J. Mater. Chem. A 2013, 1, 3068−3075. (48) Chai, S. Y.; Kim, Y. J.; Jung, M. H.; Chakraborty, A. K.; Jung, D.; Lee, W. I. Heterojunctioned BiOCl/Bi2O3, a new visible light photocatalyst. J. Catal. 2009, 262, 144−149. (49) Zamouche, M.; Hamdaoui, O. Sorption of Rhodamine B by cedar cone: effect of pH and ionic strength. Energy Procedia 2012, 18, 1228−1239. (50) Dloczik, L.; Ileperuma, O.; Lauermann, I.; Peter, L. M.; Ponomarev, E. A.; Redmond, G.; Uhlendorf, I.; Shaw, N. J. Dynamic response of dye-sensitized nanocrystalline solar cells: characterization by intensity-modulated photocurrent spectroscopy. J. Phys. Chem. B 1997, 101, 10281−10289. (51) Saini, R. K.; Singh, D.; Bhagwan, S.; Nishal, V.; Singh, I.; Kadyan, P. S. Fabrication and photovoltaic performance of nano-TiO2 based dye sensitized solar cells using azo dyes as photosensitizers. J. Nanoelectron. Optoelectron. 2016, 11, 715−722. (52) Lee, S. L.; Ho, L. N.; Ong, S. A.; Wong, Y. S.; Voon, C. H.; Khalik, W. F.; Nordin, N.; Yusoff, N. A. Enhanced electricity generation and degradation of the azo dye Reactive Green 19 in a photocatalytic fuel cell using ZnO/Zn as the photoanode. J. Cleaner Prod. 2016, 127, 579−584. (53) O’Regan, B.; Gratzel, M. A low-cost, high-efficiency solar cell based on dye-sensitized. Nature 1991, 353, 737−740. (54) Wu, T.; Liu, G.; Zhao, J.; Hidaka, H.; Serpone, N. Photoassisted degradation of dye pollutants. V. Self-photosensitized oxidative transformation of rhodamine B under visible light irradiation in aqueous TiO2 dispersions. J. Phys. Chem. B 1998, 102, 5845−5851.

4629


Controlled Growth of BiOCl with Large {010} Facets for Dye Self

Recommend Documents