Cu2O Nanoparticles and ... - ACS Publications

Subscriber access provided by READING UNIV

Article

Cu-MOF derived Cu/Cu2O nanoparticles and CuNxCy species to boost oxygen reduction activity of ketjenblack carbon in Al-air battery Jingsha Li, Nan Zhou, Jingya Song, Liang Fu, Jun Yan, Yougen Tang, and Haiyan Wang ACS Sustainable Chem. Eng., Just Accepted Manuscript • DOI: 10.1021/ acssuschemeng.7b02661 • Publication Date (Web): 03 Nov 2017 Downloaded from http://pubs.acs.org on November 4, 2017

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

ACS Sustainable Chemistry & Engineering is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 34

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Sustainable Chemistry & Engineering

Cu-MOF

derived

Cu/Cu2O

nanoparticles

and

CuNxCy species to boost oxygen reduction activity of ketjenblack carbon in Al-air battery Jingsha Lia, Nan Zhoub, Jingya Songa, Liang Fuc, Jun Yana, Yougen Tang a,d*, Haiyan Wanga,d∗ a

Hunan Provincial Key Laboratory of Efficient and Clean Utilization of Manganese

Resources, College of Chemistry and Chemical Engineering, Central South University, Lushan South Road, Changsha 410083, China b

College of Science, Hunan Agricultural University, Nongda Road, Changsha,

410128, China c

College of Chemistry and Chemical Engineering, Yangtze Normal University, Ju

Xian Road, Fuling 408100, China d

Key Laboratory of Advanced Energy Materials Chemistry (Ministry of Education),

Nankai University, Weijin Road, Tianjin 300071, China

Corresponding authors: Haiyan Wang ([email protected]) Yougen Tang ([email protected])

ABSTRACT

1

ACS Paragon Plus Environment


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Developing highly efficient and low-cost catalyst on a large scale is still a big challenge for fuel cell and metal air batteries. Decorating carbon supports by some active sites (e.g., nitrogen doping, metal-nitrogen doping) seems to be a promising strategy. In this work, we first reported Cu-centered metal organic framework (Cu-MOF) as self-sacrificing precursor to modify the ketjenblack (KB) carbon, where crystalline Cu/Cu2O nanoparticles and non-crystalline CuNxCy species were derived after calcination. The catalytic activity towards oxygen reduction reaction (ORR) of this modified KB carbon was significantly boosted probably due to the synergistic effect between crystalline Cu/Cu2O nanopaticles and non-crystalline CuNxCy species. This hybrid catalyst exhibited a comparable half-wave potential (0.82 V vs RHE) and superior limiting-current density and durability to the commercial 20 wt% Pt/C. The excellent activity was also further confirmed by the application in home-made Al-air batteries, yielding a highly stable voltage of 1.53 V at a current density of 40 mA cm-2. KEYWORDS: metallic Cu nanoparticles; Cu2O; non-crystalline CuNxCy species; oxygen reduction reaction; Al-air batteries.

INTRODUCTION Facing the problems of resource shortage, global warming and environmental pollution, various efforts are devoted to developing advanced clean energy conversion and storage technologies including fuel cells, metal-air batteries and so on.1-3 However, the sluggish kinetics of oxygen reduction reaction (ORR) in these applications has restricted their further development. Conventionally, commercial Pt/C catalysts are widely used as the state-of-the-art catalyst to ameliorate the ORR.4-5

2


Page 2 of 34

Page 3 of 34

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Nevertheless, their high price and sensitivity to CO poisoning have pushed forward a number of studies on low cost and highly efficient candidate catalyst to replace Pt/C. To date, metal-coordinated nitrogen-doped carbon materials (M-N-C, where M represents mainly Fe or Co) have been widely explored as highly efficient ORR catalysts, considering the merits of their good activity and durability.6-17 Generally, the nitrogen in these M-N-C catalysts was introduced by annealing the precursors under NH3 directly18 or the mixture of metal salts and rich-nitrogen precursors, such as melamine, cyanamide, dicyandiamide and polyaniline under flowing Ar.9, 11-12, 17, 19 However, both methods of introducing N hold the following problems. For example, the former makes the synthesis process complex, expensive and dangerous. The heat-treatment process of these rich-nitrogen precursors usually generates much gas, which could take part of product away under flowing Ar, thus leading to a low yield. Therefore, industry-scale application of these as-obtained M-N-C catalysts seems very difficult. Recently, metal-organic frameworks (MOFs) and their derivates have been investigated as self-sacrificing templates for constructing carbon-based materials and/or metal oxides as efficient ORR catalysts or battery materials due to high surface area, long-ranging ordering frame with metal centers, inherent porosity and ordered structure.20-29 Nitrogen-doped porous carbons derived from ZIF-67/glucose composite exhibited comparable ORR catalytic activity but better stability and tolerance to methanol crossover effect than commercial Pt/C.20 N-doped Fe/Fe3C@graphitic layer/carbon nanotube hybrids were fabricated by a one-step and in situ approach using MIL-101 (Fe-MOF) as precursor and the resulting materials showed excellent bi-functional catalytic activity towards ORR and OER.28 Co, N-doped porous carbons were successfully prepared by the pyrolysis of bimetallic metal-organic framework 3



1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

based on ZIF-8 and ZIF-67 with varied ratio of Zn/Co and exhibited excellent ORR catalytic activity approaching to commercial Pt/C.30 In addition to iron and cobalt, copper has also been explored as a good ORR electrocatalyst owing to the second highest electrical conductivity (less than Ag), low price and abundance.22 Highly exposed Cu(I)-N active sites within graphene31 was firstly reported as an advanced ORR catalyst via pyrolysis of copper phthalocyanine (CuPc) and dicyandiamide. However, CuPc is very expensive and dicyandiamide was decomposed to generate a lot of gas during the heat-treatment process, thus leading to a very low yield. Therefore, more deep and systematic studies of Cu-N-C should be implemented. Herein, we first reported a Cu-MOF sacrificing template method to modify the KB carbon to form a novel hybrid catalyst, in which Cu/Cu2O nanoparticles and non-crystalline CuNxCy species could be confirmed. This method is facile, scalable and of high yield. Probably owing to their synergistic effects, this hybrid catalyst exhibits superior ORR catalytic activity in terms of half-wave potential of 0.82 V vs RHE and limiting-current density (6.05 mA cm-2) in comparison to the commercial 20 wt% Pt/C. Furthermore, by cyclically scanning between 0.6 and 1.2 V vs RHE, the decreased half-wave potential of this hybrid (5 mV) is much less than that of the Pt/C catalysts (35 mV). When used in home-made Al-air batteries, it also outperforms the Pt/C catalyst.

EXPERIMENTAL SECTION Catalyst synthesis HNO3 functionalized KB: carbon support KB (ketjenblack carbon, EC-300J) was first treated in concentrated HNO3 in an oil bath at 80 °C for 8 h to get rid of metal impurities and introduce oxygen-containing functional groups on the surface. After 4


Page 4 of 34

Page 5 of 34

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


that, KB was washed with distilled water at least 10 times to remove the residual acid and then dried in vacuum oven at 110 °C for 12 h. Cu-MOF/KB: different amounts of functionalized KB (300, 400, 500, 600 mg) were dispersed in 60 mL of N, N-Dimethylformamide (DMF) with the aid of ultrasound. Then 0.296 g of copper nitrate tetrahydrate (Cu(NO3)2·4H2O), 0.272 g of 1,4-benzenedicarboxylic acid and 0.192 g of triethylene-diamine were added to the above mixture. After stirring for 30 min, the final mixture was transferred into a Teflon vessel at 120 oC for 36 h followed by naturally cooling to room temperature. The blue-grayish crystals were collected by filtration, washed with ethanol several times and dried under vacuum. The resulting Cu-MOF/KB powders in a quart boat were placed in a furnace under Ar and heated to 800 oC for 1 h with a rate of 5 oC min-1. The obtained sample was denoted as CuNC/KB-X (X represents the KB mass, namely 0, 300, 400, 500, 600 mg). For emphasizing the role of Cu-based nanoparticles, CuNC/KB-400 was leached in 0.5 M H2SO4 at 80 oC for 24 h, collected through filtering and washed several times with deionized water. Finally, the obtained product was dried at 60 oC under vacuum and denoted as CuNC/KB-400-H2SO4. Physicochemical characterization The structure of as-prepared samples was characterized on the Dandong X-ray diffractometer (TD3500) with Cu Ka radiation (λ=1.5406 Å). The morphology was investigated by transmission electron microscopy (Titan G2 60-300). X-ray 5



1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

photoelectron spectroscopy (XPS) was measured on a K-Alpha1063 spectrometer with a resolution of 0.3-0.5 eV from a monochromated aluminum anode X-ray source with Kα radiation (12 kV, 6 mA). The carbon content was carried out on a CS744 carbon and sulfur analyzer in air. Nitrogen adsorption/desorption isotherms and Barrett-Joyner-Halenda (BJH) pore size distribution were recorded at -196 °C using an

Autosorb-1 apparatus. Before the measurement, the samples were degassed at 150 oC for 3 h under vacuum. The specific surface area was calculated by using the Brunauer-Emmett-Teller (BET) equation from the adsorption isotherm. The conductivities of the as-prepared CuNC/KB-X samples were conducted on a ST-2722 semiconductor powder conductivity tester (Suzhou Jingge Electronic Co., LTD) with the height of 2.0 mm at 4.0 MPa. Electrochemical measurements 6 mg of catalyst powder was dispersed in a mixture of 950 µL of ethanol and 50 µL of Nafion with the aid of ultrasonic to form a homogeneous ink. Next, 10 µL of catalyst ink was dropped on the glassy carbon with the diameter of 5.61 mm (0.247 cm2 of geometric area) to obtain catalyst layer, yielding a catalyst loading of 0.243 mg cm-2. Finally, the as-prepared catalyst film was dried under infrared lamp for electrochemical measurements. The ORR activity of the as-prepared catalysts was evaluated by cyclic voltammetry (CV) and rotating ring-disk electrode (RRED) measurements in O2-saturated 0.1 M KOH solutions. RRDE measurements were recorded on an 6


Page 6 of 34

Page 7 of 34

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


electrochemical workstation (CHI760e) with a four-electrode cell at room temperature, in which the RRDE disk and ring were used as working electrodes, a platinum wire and saturated calomel electrode (SCE) as counter and reference electrode, respectively. The disk electrode was scanned cathodically at a rate of 10 mV s-1 in the potential range from -1.0 to 0 V vs SCE and the ring potential was constant at 0.1 V vs SCE. All the potentials measured against a SCE are converted to potential versus RHE.32-33 The number of electrons transferred (n) was calculated on the basis of Koutecky-Levich equation: 1 1 1 1 1 = + = + J J L J K Bω1 / 2 J K

Q1

B = 0.62nFC o ( Do ) 2 / 3 v −1 / 6

Q2

Where J is the measured current density, Jk and JL are the kinetic and diffusion-limiting current densities, ω is the electrode rotating rate, n represents the transferred electron number, F is Faraday’s constant, C0 is the bulk concentration of O2, D0 is the diffusion coefficient of O2, and ν is the kinematic viscosity of the electrolyte. The H2O2 yield and the electron-transfer number (n) were calculated based on the following equations: % HO2- = 200 ×

Ir N Id + Ir N

Q3

7



1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

n=4 ×

Id Id + Ir N

Page 8 of 34

Q4

Where Id is disk current, Ir is ring current, and N is current collection efficiency of the Pt ring (0.37).

Air electrode preparation The air electrode consists of gas diffusion layer, current collector and the catalytic layer. Nickel foam was employed as the current collector in air electrode due to its good conductivity and high intensity. The catalytic layer was fabricated as follows: catalysts, active carbon and acetylene black, polytetrafluoroethylene (PTFE) in a weight ratio of 3:3:1:3 were mixed well and then the paste was rolled until the thickness of this layer was about 0.2 mm. Finally, the film was pressed onto nickel foam (2 cm × 5 cm) at 15 MPa and then dried at 60 °C for 12 h. For comparison, a commercial Pt/C (20 wt% Pt, Johnson Matthey) catalyst was used. The air electrode using the Pt/C catalyst was obtained by the same process.

Al-air battery tests For Al-air full cell test, aluminium plate was used as the anode and the electrolyte was composed of 6 M KOH and 0.01 M Na2SnO3, 0.0005 M In(OH)3, 0.0075 M ZnO as corrosion inhibitors. A home-made apparatus as shown in literature was used for electrochemical measurements.2, 34

RESULTS AND DISCUSSION 8


Page 9 of 34

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


The synthesis process of CuNC/KB-X catalysts is shown in Figure 1. Firstly, the Cu-MOF/KB precursors were prepared by solvent-thermal method at 120 oC for 36 h with HNO3 functionalized KB, Cu(NO3)2·4H2O, 1,4-benzenedicarboxylic acid and triethylenediamine as raw materials, and then subjected to carbonization at 800 oC for 1 h under Ar flow. The crystal phases of as-prepared samples were investigated by powder X-ray diffraction (XRD) in Figure 2a. For CuNC/KB-0, the sharp peaks at 43.4o, 50.6o and 74.3o are assigned to the cubic phase of Cu with lattice parameter: a=b=c=3.608 Å, space group: Fm-3m (225) (JCPDS#65-9743), suggesting that partial Cu(II) in Cu-MOF (Figure S1, ESI) was reduced to metallic Cu. After adding 400mg of KB into the precursor of Cu-MOF, the hybrid phases of metallic Cu, graphitic carbon (2θ=26.3o) and Cu2O (JCPDS#05-0667) could be seen. Note that the patterns of Cu2O are very weak, indicating the slight content of impurity phase. The leach process makes the diffraction peaks of Cu2O and Cu almost disappear, revealing that Cu2O and Cu nanoparticles in the sample were almost removed during acid treatment process. We also performed X-ray photoelectron spectroscopy (XPS) of CuNC/KB-400 before and after acid treatment to further investigate the elemental composition and valence states. The results show that CuNC/KB-400 is mainly composed of C (96.74 at%), O (1.38 at%), N (1.59 at%) and Cu (0.28 at%). However, the Cu content in the CuNC/KB-400-H2SO4 (C (96.47 at%), O (1.81 at%), N (1.63 at%) and Cu (0.09 at%)) is much lower, revealed by the weaken characteristic peak of Cu (Figure 2b and S2, ESI). The high-resolution Cu 2p spectrum of CuNC/KB-400 could be fitted with four types. The peaks at 932.6 eV and 952.4 eV are corresponding to the Cu2p1/2 and 9



1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Cu2p3/2 spin-orbit peaks of Cu(0), respectively.22, 35 The Cu2p peaks at 935.0 eV and 954.5 eV belong to Cu(II),22 which should be attributed to the oxidization of Cu2O on the surface. The Cu2p XPS spectrum of CuNC/KB-400-H2SO4 is negligible (Figure 2b), further verifying the Cu-based nanoparticles were almost removed. The N 1s spectra of CuNC/KB-400 (Figure S3, ESI) could be deconvoluted into four peaks, namely, pyridinic N (~398.6 eV), pyrrolic N (~400 eV), graphitic N (~401.2 eV) and oxidized N (~402.5 eV).36-39 It is worth noting that the pyridinic N and graphitic N are generally regarded as ORR active sites.32, 40 The morphologies of Cu-MOF/KB-400, CuNC/KB-400 and CuNC/KB-400H2SO4 were characterized by transmission electron microscopy (TEM) in Figure 3. As shown in Figure 3a, the sizes of Cu-MOF nanoparticles are larger than those of CuNC/KB-400 after carbonization at 800 oC under Ar (Figure 3b), indicating that Cu-MOF are well dispersed on the surface of KB carbon. Figure 3c shows that the diameter of metallic Cu sphere, which is partially attached to carbon, is about 150 nm. The high-resolution TEM (HRTEM) image (Figure 3d) indicates that part of Cu nanoparticles are encapsulated to carbon layer and the lattice distance is determined to be 0.25 nm, corresponding to the (110) plane of cubic metallic Cu. High-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) and elemental mapping images (Figure 3g) display that C, N and O elements are uniformly dispersed throughout the whole CuNC/KB-400, while copper element is mainly focused on the copper particle. After acid leaching, the metallic Cu particles were removed, which could be confirmed by the TEM (Figure 3e), HRTEM images 10


Page 10 of 34

Page 11 of 34

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


(Figure 3f) and the HAADF-STEM and elemental mapping images (Figure 3h) of CuNC/KB-400-H2SO4. However, the energy dispersive spectroscopy (EDS, Figure S4, ESI), HAADF-STEM and elemental mapping images (Figure 3h) of CuNC/KB-400-H2SO4 also suggest that part of copper is maintained in the form of non-crystalline CuNxCy species. That is, there are three types of copper in CuNC/KB-400: Cu2O, metallic Cu nanoparticles and non-crystalline CuNxCy species. This result is also verified by the difference of the TEM and HRTEM images of CuNC/KB-400-H2SO4 and HNO3 functionalized KB (Figure S5, ESI). The conductivity test results of the as-prepared samples (Table S1, ESI) show that the bare CuNC/KB-0 exhibits the poorest conductivity (0.96 S cm-1). After adding KB, the conductivity of these composites is significantly improved. CuNC/KB-400 has the highest conductivity of 5.62 S cm-1, much better than bare KB, CuNC/KB-0 and the sum of both KB and CuNC/KB-0. Moreover, the conductivity of CuNC/KB-400 was slightly enhanced after the acid treatment process. These results also prove that KB has higher conductivity than Cu-based nanoparticles and there is a good synergistic effect on enhancing conductivity between KB and Cu-based nanoparticles. It is well known that the good conductivity could facilitate the ORR process.22, 41-42 The BET surface area and pore size distribution of the as-prepared samples were obtained by N2 adsorption-desorption isotherm. As shown in Figure 4 and Table S2, the BET surface area of CuNC/KB-0 is 19.3 m2 g-1 and it increases significantly with increasing KB content. The CuNC/KB-400 has a high surface area of 394.3 m2 g-1. The N2 adsorption-desorption isotherm of CuNC/KB-0 presents II-type curves, 11



1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 12 of 34

indicating the presence of both mesopores and macropores concentrated at 3.7 and 78.2 nm (Figure 4a). After adding KB into the precursors, an obvious hysteresis of N2 adsorption-desorption isotherms at high relative pressure appears and the pore distribution peak moves to ~ 39 nm. The carbon and sulfur analysis results show that the carbon contents of CuNC/KB-0 and CuNC/KB-400 are 20.9% and 76.8%, respectively. The ORR electrocatalytic activity of CuNC/KB-X samples was evaluated by rotating disk electrode (RDE) measurements in O2-satured 0.1 M KOH and the commercial Pt/C catalyst was used as reference (Figure 5a). Among these CuNC/KB-X catalysts, CuNC/KB-400 has the best ORR activity with a half-wave potential of 0.82 V vs RHE and a limiting-current density of 6.05 mA cm-2, even outperforming the commercial 20 wt% Pt/C catalyst. Bare CuNC/KB-0 and KB exhibit relatively poor activity. After adding KB support in the Cu-MOF precursor, the ORR performance is significantly enhanced, which should be attributed to the enhanced BET surface area and electronic conductivity.

32, 40, 43-44

More importantly,

Cu-MOF derived Cu/Cu2O nanoparticles and noncrystalline CuNxCy species on the surface of KB support could serve as active sites to accelerate ORR.45-47 Nevertheless, when the added carbon is more than 400 mg, the performance is reduced instead, especially the limiting-current density. This reveals that more active sites should be exposed in the CuNC/KB-400 hybrid since CuNC/KB-500 has an approaching conductivity and much larger BET surface area. Note that this CuNC/KB-400 hybrid

12


Page 13 of 34

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


exhibits much better ORR performance than Cu-N-C composites or KB-based materials reported in recent references (see Table. S3, ESI). 24, 27, 43, 46-49 Cyclic voltammetry (CV) curves of CuNC/KB-400 in O2-saturated and N2-saturated 0.1 M KOH are compared in Figure 5b. As observed, there are two characteristic peaks at 0.62 V and 0.88 V under both O2- and N2-saturated conditions, corresponding to the reduction peaks of Cu(I) and Cu(II).50 Obviously, CV curve in O2-saturated KOH has a strong peak at 0.80 V for ORR, while no apparent peak is observed in N2-saturated medium. A small hydrogen adsorption between 0.05 and 0.4 V is also observed.51 Note that the sample in N2-saturated solution presents a weak peak at 0.60 V, which may be attributed to the oxidization of Cu(0) in CuNC/KB-400. LSV curves of CuNC/KB-400 at various rotating rates and the corresponding Koutechy-Levich (K-L) plots at different potentials are given in Figure 5c. It is worth noting that LSV curves show a sudden change at lower rotation speed. The decrease of the current density at relatively low rotation speed can be attributed to the full integration between catalyst and oxygen causing the rapid depletion of the latter.40, 52 The K-L plots in Figure 5c (inset) display a good linearity, indicating a first-order kinetics over the potential range (0.50~0.70 V). The electron transferred number of CuNC/KB-400 calculated from K-L equation is about 4, confirming a four-electron pathway for ORR process. The Tafel slope (Fig. 5d) of CuNC/KB-400 is 69.7 mV per decade, less than that of the Pt/C (82.8 mV per decade), further confirming that the CuNC/KB-400 has better kinetic process for ORR.

13



1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

In order to better comprehend the role of metallic Cu and Cu2O nanoparticles in the resultant CuNC/KB-400 hybrid, the sample was leached in hot acid to remove Cu-based nanoparticles, which was verified by the XRD and XPS results. The ORR performance of CuNC/KB-400-H2SO4 was measured by LSV and CV curves. As shown in Figure 6a, CuNC/KB-400-H2SO4 exhibits much inferior ORR activity (more negative onset and half-wave potential, lower limiting-current density) than CuNC/KB-400. It is a remarkable fact that CuNC/KB-400-H2SO4 has slightly better electronic conductivity than CuNC/KB-400. Generally, good conductivity will facilitate the ORR process. In other words, Cu and Cu2O nanoparticles in the CuNC/KB-400 play a significant role in promoting the ORR process.22 In fact, metallic Cu and Cu2O nanoparticles have been identified as ORR active sites in many references.22, 53-54 The obvious enhanced ORR performance of CuNC/KB-400-H2SO4 compared with bare KB indicates that CuNxCy species make a great contribution to the catalytic activity of CuNC/KB-400-H2SO4.17 To sum up, there is a good synergistic effect between Cu/Cu2O nanoparticles and CuNxCy species on catalyzing ORR process. As a matter of fact, both the noncrystalline MeNxCy moieties17, 22, 31 and the crystalline metal-based nanoparticles45, 47 encased in surrounding graphitic carbon layers have been proposed as the main active sites for ORR. Our recent work discloses that crystalline Fe/Fe3C and noncrystalline FeNxCy species contributed greatly to the superior ORR catalytic activity of Fe-N-C sample with relatively high Fe content.17 CV curve shows only a well-defined cathodic peak at 0.768 V for ORR in O2-saturated 0.1 M KOH (Figure 6b), more negative than that without acid 14


Page 14 of 34

Page 15 of 34

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


treatment. It is noteworthy that the reduction peaks of Cu(I) and Cu(II) disappear, further confirming the removal of these Cu-based nanoparticles after the acid leaching. The ORR performance difference of the samples before and after acid treatment was further manifested by the rotating ring-disk electrode (RRDE) voltammograms. In the potential range of 0~0.8 V, the H2O2 percentage (Figure 6c) of CuNC/KB-400-H2SO4 reaches 16.9%, corresponding to the electron transferred number of 3.66~3.81(Figure 6d). However, that of CuNC/KB-400 remains below 3.7% and the electron transferred number varies from 3.92 to 3.94, indicating that the ORR process in CuNC/KB-400 mainly goes through 4e mechanism. This conclusion is in good agreement with the above K-L equation. All results further highlight the good synergistic effect of Cu/Cu2O nanoparticles and noncyrstalline CuNxCy species derived from Cu-MOF toward ORR. The durability of CuNC/KB-400 was evaluated by cycling the catalyst in the potential range from 0.6 to 1.2 V in O2-saturated 0.1 M KOH at 200 mV s-1. After 2000 cycles, the half-wave potential shows a very small negative shift of 5 mV and limiting-current density decrease of 0.3 mA cm-2 (Figure 7b). However, the commercial Pt/C exhibits a 35 mV negative shift of half-wave potential (Figure 7a). There is no doubt that CuNC/KB-400 possesses excellent catalytic activity and durability for ORR in alkaline solution. The ORR performance of CuNC/KB-400 catalyst was also evaluated by the practical Al-air batteries in 6 M KOH electrolyte.2 As shown in Figure 7c, the air electrode with CuNC/KB-400 as a cathode catalyst exhibits similar tend to that with Pt/C at 20 mA cm-2. However, when the discharge 15



1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

current density increases to 40 mA cm-2, it shows much higher and more stable cell voltage (1.53 V) than that of the commercial Pt/C (1.45 V), revealing better power density in practical application.

CONCLUSIONS In summary, Cu-MOF was firstly used as a self-sacrificing precursor to modify the KB carbon by a combination of facile solvothermal strategy and subsequent heat treatment. It was found that Cu-MOF derived Cu/Cu2O nanoparticles and noncyrstalline CuNxCy significantly boosted the ORR activity of KB carbon. This hybrid catalyst exhibited comparable catalytic activity and superior durability to the commercial Pt/C. It also showed much higher working voltage in home-made Al-air batteries at relatively high current density, indicating much better power density. This work can provide an important guidance for constructing high performance and scalable KB-based catalysts for ORR.

ASSOCIATED CONTENT Corresponding Authors E-mail: [email protected] (H. Wang); [email protected] (Y. Tang)

Notes The authors declare no competing financial interest.

Supporting Information XPS survey spectra, EDS, TEM image, conductivities, BET surface area and the corresponding pore diameter calculated from N2 adsorption/desorption isotherms as 16


Page 16 of 34

Page 17 of 34

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


well as summary for Cu-based and KB-based ORR catalysts in the literature were available free of charge via the Internet at http://pubs.acs.org

ACKNOWLEDGEMENTS This research was financially supported by the National Nature Science Foundation of China (No.21671200 and No.21571189), Fujian Provincial Natural Science Foundation of China (No.2015J01072), the Hunan Provincial Science and Technology Plan Project of China (No. 2016TP1007), the Science and Technology Plan Project of Changsha (No. hk1601153) and Innovation-Driven Project of Central South University (No. 2016CXS009 and No. 2016CX037).

REFERENCES 1.

Tang, Y.; Lu, L.; Roesky, H. W.; Wang, L.; Huang, B., The effect of zinc on the

aluminum anode of the aluminum-air battery. J Power Sources 2004, 138, 313-318. DOI: 10.1016/j.jpowsour.2004.06.043 2.

Tang, Y.; Qiao, H.; Wang, H.; Tao, P., Nanoparticulate Mn0.3Ce0.7O2: A novel

electrocatalyst with improved power performance for metal/air batteries. J Mater Chem A 2013, 1, 12512-12518. DOI: 10.1039/C3TA12363D 3.

Liu, K.; Huang, X.; Wang, H.; Li, F.; Tang, Y.; Li, J.; Shao, M., Co3O4-CeO2/C

as a highly active electrocatalyst for oxygen reduction reaction in Al-air batteries. ACS Appl Mater Interfaces 2016, 8, 34422-34430. DOI: 10.1021/acsami.6b12294

17



1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

4.

Page 18 of 34

Shao, M.; Chang, Q.; Dodelet, J.-P.; Chenitz, R., Recent advances in

electrocatalysts for oxygen reduction reaction. Chem Rev 2016, 116, 3594-3657. DOI: 10.1021/acs.chemrev.5b00462 5.

Shao, M.; Peles, A.; Shoemaker, K., Electrocatalysis on platinum nanoparticles:

particle size effect on oxygen reduction reaction activity. Nano Lett 2011, 11, 3714-3719. DOI: 10.1021/nl2017459 6.

Gartia, Y.; Parnell, C. M.; Watanabe, F.; Szwedo, P.; Biris, A. S.; Peddi, N.;

Nima, Z. A.; Ghosh, A., Graphene-enhanced oxygen reduction by MN4-type cobalt(III) catalyst. ACS Sustainable Chem Eng 2015, 3, 97-102. DOI: 10.1021/sc500589w 7.

Guo, J.; Cheng, Y.; Xiang, Z., Confined space assisted preparation of Fe3O4

nanoparticles modified Fe-N-C catalysts derived from covalent organic polymer for oxygen

reduction.

ACS

Sustainable

Chem

Eng

2017,

DOI:

10.1021/

acssuschemeng.7b01367. 8.

Jiang, W. J.; Gu, L.; Li, L.; Zhang, Y.; Zhang, X.; Zhang, L. J.; Wang, J. Q.; Hu,

J. S.; Wei, Z.; Wan, L. J., Understanding the high activity of Fe-N-C electrocatalysts in oxygen reduction: Fe/Fe3C nanoparticles boost the activity of Fe-Nx. J Am Chem Soc 2016, 138, 3570-3578. DOI: 10.1021/jacs.6b00757 9.

Yang, W.; Liu, X.; Yue, X.; Jia, J.; Guo, S., Bamboo-like carbon nanotube/Fe3C

nanoparticle hybrids and their highly efficient catalysis for oxygen reduction. J Am Chem Soc 2015, 137, 1436-1439. DOI: 10.1021/ja5129132

18


Page 19 of 34

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


10. Chung, H. T.; Won, J. H.; Zelenay, P., Active and stable carbon nanotube/nanoparticle composite electrocatalyst for oxygen reduction. Nat Commun

2013, 4, 1922. DOI:10.1038/ncomms2944 11. Hu, Y.; Jensen, J. O.; Zhang, W.; Cleemann, L. N.; Xing, W.; Bjerrum, N. J.; Li, Q., Hollow spheres of iron carbide nanoparticles encased in graphitic layers as oxygen reduction

catalysts.

Angew

Chem

Int

Ed

2014,

53,

3675-3679.

DOI:

10.1002/anie.201400358 12. Ding, W.; Li, L.; Xiong, K.; Wang, Y.; Li, W.; Nie, Y.; Chen, S.; Qi, X.; Wei, Z., Shape fixing via salt recrystallization: a morphology-controlled approach to convert nanostructured polymer to carbon nanomaterial as a highly active catalyst for oxygen reduction reaction. J Am Chem Soc 2015, 137, 5414-20. DOI: 10.1021/jacs.5b00292 13. Deng, D.; Yu, L.; Chen, X.; Wang, G.; Jin, L.; Pan, X.; Deng, J.; Sun, G.; Bao, X., Iron encapsulated within pod-like carbon nanotubes for oxygen reduction reaction. Angew Chem Int Ed 2013, 52, 371-375. DOI: 10.1002/anie.201204958 14. Huang, D.; Luo, Y.; Li, S.; Zhang, B.; Shen, Y.; Wang, M., Active catalysts based on Cobalt oxide@Cobalt/N-C nanocomposites for oxygen reduction reaction in alkaline solutions. Nano Res 2014, 7, 1054-1064. DOI: 10.1007/s12274-014-0468-1 15. Huang, H. C.; Shown, I.; Chang, S. T.; Hsu, H. C.; Du, H. Y.; Kuo, M. C.; Wong, K. T.; Wang, S. F.; Wang, C. H.; Chen, L. C., Pyrolyzed cobalt corrole as a potential non-precious catalyst for fuel cells. Adv Funct Mater 2012, 22, 3500-3508. DOI: 10.1002/adfm.201200264

19



1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 20 of 34

16. Jiang, Y.; Lu, Y.; Wang, X.; Bao, Y.; Chen, W.; Niu, L., A Cobalt-nitrogen complex on N-doped three-dimensional graphene framework as a highly efficient electrocatalyst for oxygen reduction reaction. Nanoscale 2014, 6, 15066-72. DOI: 10.1039/C4NR04295F 17. Li, J.; Chen, J.; Wang, H.; Ren, Y.; Liu, K.; Tang, Y.; Shao, M., Fe/N co-doped carbon materials with controllable structure as highly efficient electrocatalysts for oxygen reduction reaction in Al-air batteries. Energy Storage Mater 2017, 8, 49-58. DOI: 10.1016/j.ensm.2017.03.007 18. Niu, K.; Yang, B.; Cui, J.; Jin, J.; Fu, X.; Zhao, Q.; Zhang, J., Graphene-based non-noble-metal Co/N/C catalyst for oxygen reduction reaction in alkaline solution. J Power Sources 2013, 243, 65-71. DOI: 10.1016/j.jpowsour.2013.06.007 19. Liu, K.; Peng, Z.; Wang, H.; Ren, Y.; Liu, D.; Li, J.; Tang, Y.; Zhang, N., Fe3C@Fe/N doped graphene-like carbon sheets as a highly efficient catalyst in Al-air batteries. J Electrochem Soc 2017, 164, F475-F483. DOI: 10.1149/2.0171706jes 20. Zhang, P.; Sun, F.; Xiang, Z.; Shen, Z.; Yun, J.; Cao, D., ZIF-derived in situ nitrogen-doped porous carbons as efficient metal-free electrocatalysts for oxygen reduction

reaction.

Energy

Environ.

Sci.

2014,

7,

442-450.

DOI:

10.1039/C3EE42799D 21. Xia, W.; Zou, R.; An, L.; Xia, D.; Guo, S., A metal–organic framework route to in situ encapsulation of Co@Co3O4@C core@bishell nanoparticles into a highly ordered porous carbon matrix for oxygen reduction. Energy Environ. Sci. 2015, 8, 568-576. DOI: 10.1039/C4EE02281E 20


Page 21 of 34

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


22. Yu, H.; Fisher, A.; Cheng, D.; Cao, D., Cu,N-codoped hierarchical porous carbons as electrocatalysts for oxygen reduction reaction. ACS Appl Mater Interfaces

2016, 8, 21431-21439. DOI: 10.1021/acsami.6b04189 23. Zhong, H. X.; Wang, J.; Zhang, Y. W.; Xu, W. L.; Xing, W.; Xu, D.; Zhang, Y. F.; Zhang, X. B., ZIF-8 derived graphene-based nitrogen-doped porous carbon sheets as highly efficient and durable oxygen reduction electrocatalysts. Angew Chem Int Ed

2014, 53, 14235-14239. DOI: 10.1002/anie.201408990 24. Jahan, M.; Liu, Z.; Loh, K. P., A graphene oxide and copper-centered metal organic framework composite as a tri-functional catalyst for HER, OER, and ORR. Adv Funct Mater 2013, 23, 5363-5372. DOI: 10.1002/adfm.201300510 25. Yue, H.; Shi, Z.; Wang, Q.; Cao, Z.; Dong, H.; Qiao, Y.; Yin, Y.; Yang, S., MOF-derived cobalt-doped ZnO@C composites as a high-performance anode material for lithium-ion batteries. ACS Appl Mater Interfaces 2014, 6, 17067-17074. DOI: 10.1021/am5046873 26. Babu, K. F.; Kulandainathan, M. A.; Katsounaros, I.; Rassaei, L.; Burrows, A. D.; Raithby, P. R.; Marken, F., Electrocatalytic activity of basolitetm F300 metal-organic-framework structures. Electrochem Commun 2010, 12, 632-635. DOI: 10.1016/j.elecom.2010.02.017 27. Mao, J.; Yang, L.; Yu, P.; Wei, X.; Mao, L., Electrocatalytic four-electron reduction of oxygen with copper(II)-based metal-organic frameworks. Electrochem Commun 2012, 19, 29-31. DOI: 10.1016/j.elecom.2012.02.025

21



1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 22 of 34

28. Li, J. S.; Li, S. L.; Tang, Y. J.; Han, M.; Dai, Z. H.; Bao, J. C.; Lan, Y. Q., Nitrogen-doped Fe/Fe3C@graphitic layer/carbon nanotube hybrids derived from mofs: efficient bifunctional electrocatalysts for ORR and OER. Chem Commun 2015, 51, 2710-2713. DOI: 10.1039/C4CC09062D 29. Sun, D.; Tang, Y.; Ye, D.; Yan, J.; Zhou, H.; Wang, H., Tuning the morphologies of mno/c hybrids by space constraint assembly of Mn-MOFs for high performance Li Ion

batteries.

ACS

Appl

Mater

Interfaces

2017,

9,

5254-5262.

DOI:

10.1021/acsami.6b14801 30. Chen, Y. Z.; Wang, C.; Wu, Z. Y.; Xiong, Y.; Xu, Q.; Yu, S. H.; Jiang, H. L., From bimetallic metal-organic framework to porous carbon: high surface area and multicomponent active dopants for excellent electrocatalysis. Adv Mater 2015, 27, 5010-5016. DOI: 10.1002/adma.201502315 31. H. Wu, H. Li, X. Zhao, Q. Liu, J. Wang, J. Xiao, S. Xie, R. Si, F. Yang, S. Miao, X. Guo, G. Wang, X. Bao, Highly doped and exposed Cu(I)–N active sites within graphene towards efficient oxygen reduction for Zinc–air batteries. Energy Environ. Sci. 2016, 9, 3736-3745. DOI: 10.1039/C6EE01867J 32. Liang, Y.; Wang, H.; Zhou, J.; Li, Y.; Wang, J.; Regier, T.; Dai, H., Covalent hybrid of spinel manganese-cobalt oxide and graphene as advanced oxygen reduction electrocatalysts. J Am Chem Soc 2012, 134, 3517-3523. DOI: 10.1021/ja210924t 33. Cheng, F.; Shen, J.; Peng, B.; Pan, Y.; Tao, Z.; Chen, J., Rapid room-temperature synthesis

of

nanocrystalline

spinels

as

oxygen

reduction

electrocatalysts. Nat Chem 2011, 3, 79-84. DOI: 10.1038/nchem.931 22


and

evolution

Page 23 of 34

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


34. Zhang, H.; Qiao, H.; Wang, H.; Zhou, N.; Chen, J.; Tang, Y.; Li, J.; Huang, C., Nickel cobalt oxide/carbon nanotubes hybrid as a high-performance electrocatalyst for metal/air battery. Nanoscale 2014, 6, 10235-10242. DOI: 10.1039/C4NR02125H 35. Noh, S. H.; Seo, M. H.; Ye, X.; Makinose, Y.; Okajima, T.; Matsushita, N.; Han, B.; Ohsaka, T., Design of an active and durable catalyst for oxygen reduction reactions using encapsulated cu with n-doped carbon shells (Cu@N-C) activated by CO2

treatment.

J.

Mater.

Chem.

A

2015,

3,

22031-22034.

DOI:

10.1039/C5TA06108C 36. Lin, L.; Zhu, Q.; Xu, A. W., Noble-metal-free Fe-N/C catalyst for highly efficient oxygen reduction reaction under both alkaline and acidic conditions. J Am Chem Soc

2014, 136, 11027-11033. DOI: 10.1021/ja504696r 37. Liu, R.; Wu, D.; Feng, X.; Mullen, K., Nitrogen-doped ordered mesoporous graphitic arrays with high electrocatalytic activity for oxygen reduction. Angew Chem Int Ed 2010, 49, 2565-2569. DOI: 10.1002/ange.200907289 38. Yu, H.; Shang, L.; Bian, T.; Shi, R.; Waterhouse, G. I.; Zhao, Y.; Zhou, C.; Wu, L. Z.; Tung, C. H.; Zhang, T., Nitrogen-doped porous carbon nanosheets templated from g-C3N4 as metal-free electrocatalysts for efficient oxygen reduction reaction. Adv Mater 2016, 28, 5080-5086. DOI: 10.1002/adma.201600398 39. Zhang, H.; Li, H.; Wang, H.; He, K.; Wang, S.; Tang, Y.; Chen, J., NiCo2O4/N-doped graphene as an advanced electrocatalyst for oxygen reduction reaction. J Power Sources 2015, 280, 640-648. DOI: 10.1016/j.jpowsour.2015.01.147

23



1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 24 of 34

40. Li, J.; Zhou, Z.; Liu, K.; Li, F.; Peng, Z.; Tang, Y.; Wang, H., Co3O4/Co-N-C modified ketjenblack carbon as an advanced electrocatalyst for Al-air batteries. J Power Sources 2017, 343, 30-38. DOI: 10.1016/j.jpowsour.2017.01.018 41. Wang, Y.; Lu, X.; Liu, Y.; Deng, Y., Silver supported on Co3O4 modified carbon as electrocatalyst for oxygen reduction reaction in alkaline media. Electrochem Commun 2013, 31, 108-111. DOI: 10.1016/j.elecom.2013.03.017 42. Xu, L.; Jiang, Q.; Xiao, Z.; Li, X.; Huo, J.; Wang, S.; Dai, L., Plasma-engraved Co3O4 nanosheets with oxygen vacancies and high surface area for the oxygen evolution reaction. Angew Chem Int Ed 2016, 55, 1-6. DOI: 10.1002/ange.201600687 43. Chen, J.; Zhou, N.; Wang, H.; Peng, Z.; Li, H.; Tang, Y.; Liu, K., Synergistically enhanced oxygen reduction activity of MnOx-CeO2/ketjenblack composites. Chem Commun 2015, 51, 10123-10126. DOI: 10.1039/C5CC02343B 44. Liang, Y.; Li, Y.; Wang, H.; Zhou, J.; Wang, J.; Regier, T.; Dai, H., Co3O4 nanocrystals on graphene as a synergistic catalyst for oxygen reduction reaction. Nat Mater 2011, 10, 780-786. DOI: 10.1038/nmat3087 45. Luo, B.; Li, X.; Yang, J.; Li, X.; Xue, L.; Li, X.; Gu, J.; Wang, M.; Jiang, L., Non-enzymatic electrochemical sensors for the detection of hydrogen peroxide based on

Cu2O/Cu

nanocomposites.

Analytical

Methods

2014,

6,

1114.

DOI:

10.1039/C3AY41914B 46. Su, C. Y.; Liu, B. H.; Lin, T. J.; Chi, Y. M.; Kei, C. C.; Wang, K. W.; Perng, T. P., Carbon nanotube-supported Cu3N nanocrystals as a highly active catalyst for

24


Page 25 of 34

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


oxygen reduction reaction. J. Mater. Chem. A 2015, 3, 18983-18990. DOI: 10.1039/C5TA04383B 47. H. Li, Y. Xu, H. Sitinamaluwa, K. Wasalathilake, D. Galpaya, C. Yan, Cu Nanoparticles Supported on Graphitic Carbon Nitride as an Efficient Electrocatalyst for Oxygen Reduction Reaction, Chinese J Catal 2017, 38, 1006-1010. DOI: 10.1016/S1872-2067(17)62764-5 48. Lee, J. S.; Park, G. S.; Lee, H. I.; Kim, S. T.; Cao, R.; Liu, M.; Cho, J., Ketjenblack carbon supported amorphous manganese oxides nanowires as highly efficient electrocatalyst for oxygen reduction reaction in alkaline solutions. Nano Lett

2011, 11, 5362-5366. DOI: 10.1021/nl2029078 49. Lai, Q.; Zhu, J.; Zhao, Y.; Liang, Y.; He, J.; Chen, J., MOF-based metal-doping-induced synthesis of hierarchical porous CuN/C oxygen reduction electrocatalysts

for

Zn-air

batteries.

Small

2017,

1700740.

DOI:

10.1002/smll.201700740 50. Zamanzad Ghavidel, M. R.; Monteverde Videla, A. H. A.; Specchia, S.; Easton, E. B., The relationship between the structure and ethanol oxidation activity of pt-cu/c alloy

catalysts.

Electrochimica

Acta

2017,

230,

58-72.

DOI:

10.1016/j.electacta.2017.01.129 51. Li, H.-H.; Cui, C.-H.; Zhao, S.; Yao, H.-B.; Gao, M.-R.; Fan, F.-J.; Yu, S.-H., Mixed-PtPd-shell PtPdCu nanoparticle nanotubes templated from copper nanowires as efficient and highly durable electrocatalysts. Adv Energy Mater 2012, 2, 1182-1187. DOI: 10.1002/aenm.201200207 25



1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

52. Wang, Y.; Kong, A.; Chen, X.; Lin, Q.; Feng, P., Efficient oxygen electroreduction: hierarchical porous Fe–N-doped hollow carbon nanoshells. ACS Catal 2015, 5, 3887-3893. DOI: 10.1021/acscatal.5b00530 53. He, Q.; Yang, X.; Ren, X.; Koel, B. E.; Ramaswamy, N.; Mukerjee, S.; Kostecki, R., A novel CuFe-based catalyst for the oxygen reduction reaction in alkaline media. J Power Sources 2011, 196, 7404-7410. DOI: 10.1016/j.jpowsour.2011.04.016 54. Kato, M.; Murotani, T.; Yagi, I., Bioinspired iron- and copper-incorporated carbon electrocatalysts for oxygen reduction reaction. Chem Lett 2016, 45, 1213-1215. DOI: 10.1246/cl.160573

26


Page 26 of 34

Page 27 of 34

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Figure 1. Synthetic process for the CuNC/KB-X catalysts

27



1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 2. (a) XRD patterns of the CuNC/KB-0 (blue), CuNC/KB-400 (red) and CuNC/KB-400-H2SO4 (black) and (b) high resolution spectra of the Cu2p XPS peaks of CuNC/KB-400 and CuNC/KB-400-H2SO4.

28


Page 28 of 34

Page 29 of 34

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Figure 3. TEM images of (a) Cu-MOF/KB-400, (b-c) CuNC/KB-400 and (e) CuNC/KB-400-H2SO4;

HRTEM

image

of

(d)

CuNC/KB-400

and

(f)

CuNC/KB-400-H2SO4; HAADF-STEM images and copper, carbon, nitrogen and oxygen

elemental

mapping

images

of

(g)

CuNC/KB-400

CuNC/KB-400-H2SO4.

29


and

(h)


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 4. N2 adsorption/desorption isotherms and the corresponding pore size distribution curves (inset) of CuNC/KB-0 (a), CuNC/KB-300 (b), CuNC/KB-400 (c) and CuNC/KB-500 (d).

30


Page 30 of 34

Page 31 of 34

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Figure 5. (a) LSV curves for various as-prepared CuNC/KB-X samples, KB and the commercial Pt/C catalyst with the catalyst loading of about 0.243 mg cm-2 in O2-saturated 0.1 M KOH at a sweep rate of 10 mV s-1. (b) CV curves of the CuNC/KB-400 in O2-saturated (solid line) and N2-saturated (dashed line) 0.1 M KOH at 10 mV s-1. (c) LSV curves of the CuNC/KB-400 in O2-saturated 0.1 M KOH at 10 mV s-1 at different rotating rates. The inset is Koutecky-Levich (K-L) plots at different potentials (0.50, 0.55, 0.60, 0.65 and 0.70 V vs. RHE). (d) Tafel plots for CuNC/KB-400 (black line) and commercial Pt/C (red line) catalysts calculated from Figure 5(a).

31



1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 6. (a) LSV curves for the CuNC/KB-400 catalyst before and after acid treatment and (b) CV curves for the CuNC/KB-400 catalyst before and after acid treatment in O2-saturated 0.1 M KOH at a sweep rate of 10 mV s-1. H2O2 yield (c) and electron transfer numbers (d) of the CuNC/KB-400 catalyst before and after acid treatment at a potential range of 0.1~0.8 V calculated from RRDE voltammograms.

32


Page 32 of 34

Page 33 of 34

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Figure 7. LSV curves comparison of Pt/C (a) and CuNC/KB-400 (b) for ORR in O2-saturated 0.1 M KOH at a sweep rate of 200 mV s-1 before (red) and after (black) 2000 cycles. The constant current discharge curves of Al-air batteries with Pt/C (red circle) and CuNC/KB-400 (black cubic) as cathode catalysts at 20 (c) and 40 mA cm-2 (d).

33



1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Synopsis:

A novel hybrid, Cu/Cu2O nanoparticles and noncrystalline CuNxCy

species modified ketjenblack, was investigated as an ORR catalyst for the first time and exhibited comparable ORR catalytic activity and superior durability to 20 wt% Pt/C.

34


Page 34 of 34

Cu2O Nanoparticles and ... - ACS Publications

Recommend Documents