Subscriber access provided by UB + Fachbibliothek Chemie | (FU-Bibliothekssystem)
Article
Control of Mg2+/Ca2+ activity ratio on the formation of crystalline carbonate minerals via an amorphous precursor Bettina Purgstaller, Florian Konrad, Martin Dietzel, Adrian Immenhauser, and Vasileios Mavromatis Cryst. Growth Des., Just Accepted Manuscript • DOI: 10.1021/acs.cgd.6b01416 • Publication Date (Web): 24 Jan 2017 Downloaded from http://pubs.acs.org on January 25, 2017
Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.
Crystal Growth & Design is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.
Page 1 of 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Crystal Growth & Design
1
Control of Mg2+/Ca2+ activity ratio on the formation of crystalline carbonate
2
minerals via an amorphous precursor
3
Bettina Purgstaller*1, Florian Konrad1, Martin Dietzel1, Adrian Immenhauser2, Vasileios Mavromatis1,3
4
1
Institute of Applied Geosciences, Graz University of Technology, Rechbauerstrasse 12, 8010 Graz, Austria
5
2
Institute of Geology, Mineralogy and Geophysics, Bochum, Universitätsstraße 150, 44801 Bochum, Germany
6
3
Géosciences Environnement Toulouse, CNRS, UMR5563, Avenue Edouard Belin 14, 31400 Toulouse, France
7 8
In the present work the transformation of Mg-rich amorphous calcium carbonate (Mg-ACC) into
9
crystalline carbonate phases has been studied at distinct initial Mg/Ca ratios (1/3 to 1/8) under
10
controlled pH conditions (7.8 to 8.8). The experimental results revealed two pathways of Mg-
11
ACC transformation strictly depending on the prevailing ratio of the Mg2+ to Ca2+ activity,
12
aMg2+/aCa2+, of the reactive solution after Mg-ACC was synthesized: Mg-ACC transformed to (i)
13
Mg-calcite at 5 ≤ aMg2+/aCa2+ ≤ 8 and to (ii) monohydrocalcite at 8 ≤ aMg2+/aCa2+ ≤ 12. Once the
14
reactive solution reaches saturation with ACC it exhibits high supersaturation with respect to
15
crystalline carbonate minerals, which promotes their formation and parallel initiates the
16
dissolution of Mg-ACC. At a high aMg2+/aCa2+ the time period of metastability of Mg-ACC in the
17
reactive solution (tACC) is prolonged due to the inhibition of calcite formation and the slow
18
precipitation kinetics of monohydrocalcite. These observations suggest that the formation
19
behavior of the crystalline phases is the rate-limiting process in the transformation of Mg-ACC.
20 21 22 23 24 25 26 27 28 29
Bettina Purgstaller Institute of Applied Geosciences Graz University of Technology Rechbauerstrasse 12 8010 Graz, Austria Telephone: +43 (0) 316/ 873-6362 e-mail:
[email protected] 1 ACS Paragon Plus Environment
Crystal Growth & Design
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
30
Control of Mg2+/Ca2+ activity ratios on the formation
31
of crystalline carbonate minerals via an amorphous
32
precursor
33
Bettina Purgstaller*1, Florian Konrad1, Martin Dietzel1, Adrian Immenhauser2, Vasileios
34
Mavromatis1,3
35
1
36
Graz, Austria
37
2
38
150, 44801 Bochum, Germany
39
3
40
Toulouse, France
41 42
*Corresponding author:
[email protected] Institute of Applied Geosciences, Graz University of Technology, Rechbauerstrasse 12, 8010
Institute of Geology, Mineralogy and Geophysics, Ruhr-Universität Bochum, Universitätsstraße
Géosciences Environnement Toulouse, CNRS, UMR5563, avenue Edouard Belin 14, 31400
43
2 ACS Paragon Plus Environment
Page 2 of 32
Page 3 of 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Crystal Growth & Design
44
ABSTRACT
45
The formation of amorphous calcium carbonate (ACC) and its transformation to crystalline
46
phases plays a key role on the formation of carbonate minerals on Earth’s surface environments.
47
Nonetheless, the psychochemical parameters controlling the formation of crystalline CaCO3 via
48
an amorphous precursor are still under debate. In the present study the possibility of crystalline
49
CaCO3 formation via an ACC precursor in the pH range from 7.8 to 8.8 and at initial Mg/Ca
50
ratios from 1/3 to 1/8 is experimentally investigated. The obtained results document that the
51
transformation of Mg-rich ACC (Mg-ACC) to a crystalline phase is strictly controlled by the
52
prevailing ratio of the Mg2+ to Ca2+ activity, aMg2+/aCa2+, of the reactive solution after Mg-ACC
53
was synthesized: Mg-ACC transformed to (i) Mg-calcite at 5 ≤ aMg2+/aCa2+ ≤ 8 and to (ii)
54
monohydrocalcite at 8 ≤ aMg2+/aCa2+ ≤ 12. Our findings suggest that the formation of the
55
crystalline phase induces undersaturation of the reactive solution with respect to the ACC and
56
triggers its dissolution. Thus, the metastability of Mg-ACC in the reactive solution is not
57
determined by its Mg content, but is related to the formation kinetics of the less soluble
58
crystalline phase. The experimental results highlight the importance of prevailing
59
physicochemical conditions of the reactive solution on Mg-ACC transformation pathways.
60 61
INTRODUCTION
62
Calcium carbonate (CaCO3) occurs in three anhydrous crystalline forms, calcite, aragonite
63
and vaterite, and two hydrous crystalline forms, monohydrocalcite (CaCO3·H2O) and ikaite
64
(CaCO3·6H2O). Of these calcium carbonate minerals, the geological occurrence of the less stable
65
vaterite, monohydrocalcite, and ikaite is rare.1-4 In contrast, calcite and aragonite are deposited
66
readily in marine and terrestrial environments.5 Many biogenic and non-biogenic calcites contain 3 ACS Paragon Plus Environment
Crystal Growth & Design
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
67
significant amounts of magnesium.6-7 Calcites with more than 4 mol% magnesium are generally
68
referred to as Mg-calcites.
69
As early as the 19th century, it has been observed that biominerals can be formed via an
70
amorphous calcium carbonate (ACC) phase.8-9 Since then, the presence of an ACC precursor has
71
been observed in the skeletons of sea urchins,10-11 freshwater snails,12-13 bivalves,14 brachiopods,15
72
ascidians,16 sponges,17 and crustaceans.18 More recently, amorphous carbonate phases were found
73
in intracellular inclusions in modern microbialites in Lake Alchichica19 and in the mucilaginous
74
matrix embedding planktonic cells in Lake Geneva.20 With respect to abiotic precipitation
75
environments, ACC formation and its transformation to calcite was for instance associated with
76
speleothem formation in caves21 and found to be applicable for medical product development.22-23
77
By mixing concentrated solutions of CaCl2 and Na2CO3, Brečević and Nielsen24 showed
78
that ACC is highly soluble (Ksp-ACC = 10-6.39 at 25°C); and that it rapidly transforms to crystalline
79
calcium carbonate polymorphs. In this context, it has been observed that organic molecules and
80
magnesium ions stabilize both biogenic and inorganic ACC.25-32 In the latter case, the elevated
81
metastability of Mg enriched amorphous calcium carbonate (Mg-ACC) was attributed to the
82
structural water bound to Mg ions that retards the process of dehydration and transformation.
83
Despite the fact that numerous studies have focused on ACC formation, the mechanisms
84
controlling its transformation into, for instance, (Mg-)calcite and/or aragonite is poorly
85
understood. The literature of the last decade has revealed that the crystallization pathways of the
86
amorphous phase depend on physicochemical parameters including temperature,33 pH,32,34
87
solution additives like magnesium ions26,27,32 and organic molecules.27
88
For example, when ACC was synthesized from a solution with a high initial pH (> 9.5), it
89
transformed to calcite via metastable vaterite.32,35 Conversely, by using Mg in the initial solution
90
(Mg/Ca = 1/9) ACC crystallized directly to (Mg-)calcite.32 On the other hand, by mixing 4 ACS Paragon Plus Environment
Page 4 of 32
Page 5 of 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Crystal Growth & Design
91
solutions with molar Mg/Ca ratios ≥ 1/5.6 and CO3/Ca ratios > 1, monohydrocalcite formation
92
was reported to proceed through an ACC precursor.36-38 In this context, it has been suggested that
93
ACC crystallizes through a nucleation controlled dissolution-reprecipitation reaction.35,38,39 In
94
contrast, many studies suggested that the short-range structure or the composition of ACC (e.g.
95
Mg content) controls its crystallization to a distinct crystalline carbonate phase.26, 27, 34
96
Most of the former studies dealing with (Mg-)ACC formation were conducted at solution
97
pH > 9.5,31,32,35,36,39 a value that is significantly higher than the pH of most natural aquatic
98
environments. Moreover, (Mg-)ACC was synthesized by batch methods with CaCl2/MgCl2 and
99
NaHCO3/Na2CO3 solutions, where the pH decreased from ~11 to ~8 during mixing and
100
subsequent (Mg-)ACC crystallization.32,35 In the context of this study, we conducted experiments
101
under controlled physicochemical conditions (constant T and pH) in order to shed light on the
102
role of circum-neutral pH regimes and effects of Mg/Ca ratios during the (trans-)formation of
103
Mg-ACC to crystalline phases. Specifically, the transformation pathways of Mg-ACC were
104
systematically examined from pH 7.8 to 8.8 at distinct Mg/Ca ratios (1/3 to 1/8) and discussed
105
together with our previous study at pH 8.3.40 The aim of the present paper is to provide a more
106
detailed understanding on the mechanisms controlling the formation of crystalline carbonate
107
phases via a Mg-ACC precursor.
108 109
METHODS
110
Experimental setup and analytical procedures
111
The synthesis of a solid Ca1-xMgxCO3 phase was carried out under controlled
112
physicochemical conditions (T and pH = constant) using the experimental setup described in
113
Purgstaller et al.40. Hereafter, only the most important features are described. The precipitation of
114
Ca1-xMgxCO3 was induced by the titration (702 SM Titrino titrator; Methrom) of 50 ml of a 0.6 5 ACS Paragon Plus Environment
Crystal Growth & Design
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
115
M (Ca,Mg)Cl2 solution with distinct Mg/Ca ratios (1/3, 1/4, 1/6 and 1/8) at a rate of 2 ml/min into
116
50 ml of a 1 M NaHCO3/Na2CO3 solution at 25.00 ±0.03°C (Easy MaxTm 102; Mettler Toledo).
117
The pH of the reactive solution was kept constant at values of 7.8, 8.3, or 8.8 ±0.1 by the
118
automatic titration of a 1 M NaOH solution (Schott; TitroLine alpha plus), with titration steps of
119
0.1 ml. Experiments conducted with the Mg/Ca ratios 1/4, 1/6 and 1/8 are labeled as A1, A2 and
120
A3 at pH 7.8 and as C1, C2 and C3 at pH 8.8, respectively (Table 1). A replicate experiment of
121
C1 is labeled as C1_2. One experiment was carried out at pH 8.3 with a Mg/Ca ratio of 1/3 (exp.
122
MgCa3, Table 1). Prior to each experiment the pH of the carbonate buffer solution was adjusted
123
to the required experimental pH (±0.07) using a 1 M NaOH or a 1 M HCl solution.
124
During the experimental run, the temporal evolution of mineral precipitation was monitored
125
by in situ Raman spectroscopy (Raman RXN2TM analyzer, Kaiser Optical Systems). After 180
126
min of reaction time, the reactive solution was transferred into a 150 ml glass bottle and placed
127
air-tight on a compact shaker (Edmund Bühler GmbH; KS-15) operating at 150 rpm in a
128
temperature controlled room at 25 ±1°C. In each experiment, 5 ml of the reactive solution were
129
sampled after selected time steps for solid and solution analysis. Immediately after sampling the
130
solids were separated by a 0.2 µm cellulose acetate filter using a suction filtration unit and were
131
analyzed using Attenuated Total Reflectance - Fourier Transform Infrared Spectroscopy (ATR-
132
FTIR; Perkin Elmer Spektrum 100). The solids were subsequently dried at room temperature in a
133
desiccator using silica gel. The mineralogy of the dried precipitates was determined using X-ray
134
diffraction (PANalytical X´Pert PRO) and the mineral phases were quantified using Rietveld
135
refinement (software HighScore Plus, PANalytical, PDF-2 database). Selected precipitates were
136
gold coated and imaged using a scanning electron microscope (SEM, ZEISS DSM 982 Gemini).
137
The aqueous cation concentrations were determined using ion chromatography (Dionex IC S
138
3000, IonPac®, AS19 and CS16 column), with an analytical precision of ±3%. The total 6 ACS Paragon Plus Environment
Page 6 of 32
Page 7 of 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Crystal Growth & Design
139
alkalinity of the solutions was measured by a Schott TitroLine alpha plus titrator using a 0.02 M
140
HCl solution with a precision better than ±2% and a detection limit of 5 x 10-6 M.
141
The Mg content of the solids (in mol%) sampled at a given reaction time was calculated
142
according to the equation:
143
[Mg]solid = [Mg]
144
where [Mg]add and [Ca]add are the concentrations of added Mg and Ca by titration into the reactive
145
solution given in mol L-1 considering at any time volume change in the reaction solutions. [Mg]aq
146
and [Ca]aq are the measured molar concentrations of Mg and Ca in the reactive solutions. The
147
calculated [Mg]solid values obtained from Eq. 1 are in excellent agreement (R² = 0.96) with the
148
Mg contents of the bulk digested solids analyzed by inductively coupled plasma optical emission
149
spectrometry (Perkin Elmer Optima 8300 DV) (Figure S1). The analytical error was calculated to
150
be < ±3% for Ca and Mg.
[Mg]add - [Mg]aq
add -[Mg]aq +
[Ca]add - [Ca]aq
·100
(1)
151 152
Hydrochemical modeling
153
The aqueous speciation and ion activities of the reactive solutions were calculated using
154
the PHREEQC software (minteq.v4 database). The saturation Index (SI) of the reactive solution
155
with respect to ACC was calculated using the equation (aCa2+ ) . (a
CO3 2-
)
156
SIACC = log
157
where a denotes the activity of the ith species in solution and the solubility product (Ksp) is 10-6.39
158
at 25°C. 24
K sp
(2)
159
7 ACS Paragon Plus Environment
Crystal Growth & Design
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
160
RESULTS
161
Solid phase characterization
162
The in situ Raman spectra of experiments A1, A2, and A3 carried out at pH 7.8 showed
163
that Mg-calcite is present right after the onset of the experiments within 1 min, as it was indicated
164
by the increase of intensity of the carbonate stretching band (v1) at ~1087 cm-1 (exp. A1, Figure
165
1A) and of the libration mode of Mg-calcite at ~282 cm-1 (see values in Table 2).41 The intensity
166
of the Raman v1 band for Mg-calcite was constant over time as soon as the titration of the
167
(Ca,Mg)Cl2 solution was stopped (exp. A1, Figure 1A). In experiments A2 and A3, aragonite was
168
identified in addition to Mg-calcite after 180 min of reaction time detectable through the presence
169
of the libration mode at ~205 cm-1 in the Raman spectra (Table 2).42 The results obtained by
170
Raman spectroscopy are in good agreement with the ATR-FTIR analysis, showing the
171
characteristic vibration band of Mg-calcite at ~711 cm-1 (v4)43 in all precipitates and the presence
172
of aragonite by the ATR-FTIR bands at ~699 cm-1 (v4) and ~856 cm-1 (v2)44 after 25 min of
173
reaction time in experiments A2 and A3 (Table 2). Moreover, the ATR-FTIR spectra of the
174
precipitates that were sampled between 13 and 25 min and between 13 and 180 min in
175
experiments A2 and A3, respectively, showed vibration bands at ~743 cm-1 (v4) corresponding to
176
vaterite (Table 2). 44 The discrepancy of the analyzed mineralogy at certain reaction times within
177
a single experiment (Table 2) is attributed to the higher sensitivity of the ATR-FTIR analysis of
178
the collected solids compared to that of the in situ Raman spectroscopy of the reactive
179
solution/suspension.
180
Quantitative XRD results (Table 3) showed that the dried precipitates of experiment A1
181
mainly consist of Mg-calcite (96 ±2 wt. %) and traces of aragonite (4 ±2 wt. %). In experiments
8 ACS Paragon Plus Environment
Page 8 of 32
Page 9 of 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Crystal Growth & Design
182
A2 and A3 vaterite (up to 21 wt. %) and aragonite (13-33 wt. %) can be found additionally to
183
Mg-calcite, which is abundant in the bulk precipitate (61-75 wt. %).
184
The SEM images of the precipitates of experiments A1, A2 and A3, sampled after 1 day
185
of reaction time, showed aggregates (~4 µm) of rhombohedral Mg-calcite crystals (Figure 2A-C),
186
which are similar in texture to those obtained in experiment MgCa8 from Purgstaller et al.40
187
(Figure 2F). The Mg-calcite crystals are smaller in size (< 0.1 µm) in experiment A1 compared to
188
those from experiments A2 (~0.3 µm) and A3 (~1 µm). Moreover, in experiment A1 Mg-calcite
189
crystal habits are more elongated (Figure 2A) compared to those from experiments A2 (Figure
190
2B) and A3 (Figure 2C). Finally, in the A2 and A3 experiments, pseudo-hexagonal crystals of
191
aragonite (~1 µm) were observed (exp. A3 in Figure S2A).
192
In experiments C1, C2, and C3 carried out at pH 8.8 the collected in situ Raman spectra
193
revealed the presence of only Mg-ACC within 58, 40, and 36 min of reaction time, respectively.
194
The Raman spectra of Mg-ACC are characterized by a single broad v1 band at 1082 ±1 and by the
195
absence of lattice modes
196
ATR-FTIR analyses of sampled precipitates (exp. C1 in Figure 1B, Table 2). The lack of the v4
197
vibration band and the presence of vibration bands at 860-861 cm-1 and 1073 ±1 cm-1 in the ATR-
198
FTIR spectra are characteristic of Mg-ACC.26 In the experiment conducted with the highest
199
Mg/Ca ratio (exp. C1), a Raman band at ~1068 cm-1 corresponding to the v1 band of
200
monohydrocalcite46 evolved after 58 min of reaction time, while the characteristic band of Mg-
201
ACC at ~1083 cm-1 decreased (Figure 1B). ATR-FTIR spectra of the precipitates collected after
202
180 min of reaction time showed vibration bands at ~697/~726 cm-1, ~755 cm-1, ~871 cm-1,
203
~1068 cm-1 and ~1395/~1474 cm-1 (Figure 1B). These ATR-FTIR bands are in good agreement
204
with wavenumber values for synthetic monohydrocalcite from Neumann and Epple47. Similar in
205
situ Raman and ATR-FTIR results were obtained in the replicate experiment C1_2 (Table S1).
45
(exp. C1 in Figure 1B; Table 2). These results were confirmed by
9 ACS Paragon Plus Environment
Crystal Growth & Design
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 10 of 32
206
After 1 day of reaction time, the in situ Raman spectra indicated the presence of a second v1 band
207
at ~1100 cm-1 (Table 2), corresponding to nesquehonite46. In contrast to the in situ Raman
208
spectroscopic observations, the presence of nesquehonite was not detectable by ATR-FTIR
209
analysis due to similarities of the vibration bands of monohydrocalcite and nesquehonite at higher
210
wavenumbers in the ATR-FTIR spectra. The XRD results showed that the dried precipitate
211
consists of Mg-calcite at 25 min of reaction time, whereas monohydrocalcite was found in the
212
precipitate sampled at 180 min of reaction time (Table 3). After 1 day of reaction time
213
nesquehonite (14 wt. %) was detected beside monohydrocalcite (86 wt. %, Table 3).
214
In contrast, in experiments conducted with the Mg/Ca ratios 1/6 and 1/8 (exp. C2 and C3),
215
in situ Raman spectroscopy revealed the transformation of Mg-ACC to Mg-calcite (exp. C3 in
216
Figure S3). The formation of Mg-calcite was indicated by the rise of the translation mode of Mg-
217
calcite at ~283 cm-1 (Table 2) and the rise of the intensity of the v1 Raman vibration band at 1088
218
cm-1.40 The results obtained by in situ Raman spectroscopy are in good agreement with those
219
obtained by ATR-FTIR analysis (Table 2). As reported in Table 3 the XRD patterns of all dried
220
precipitates in experiments C2 and C3 showed only Mg-calcite.
221
The monohydrocalcite obtained in experiment C1 forms non-aggregated nano-spheres
222
(exp. C1, Figure 2G), whereas the nesquehonite precipitates of experiment C1 are rod-shaped
223
with individual rods reaching lengths of up to 40 µm (Figure S2B). The Mg-calcites of
224
experiments C2 (Figure 2H) and C3 (Figure 2I) display aggregates composed of nanoparticles (~
225
80 nm) that agglomerated to larger clusters. These particles are significantly smaller in size than
226
the Mg-calcite crystals resulting from experiments conducted at pH 7.8 (Figure 2A-C). The Mg-
227
calcite aggregates however are similar in texture to those observed in experiments MgCa4
228
(Figure 2D) and MgCa6 (Figure 2E) conducted at pH 8.3 by Purgstaller et al.40 where Mg-calcite
229
was formed via Mg-ACC. 10 ACS Paragon Plus Environment
Page 11 of 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Crystal Growth & Design
230
The collected in situ Raman spectra of experiment MgCa3 conducted at pH 8.3 (Mg/Ca =
231
1/3) showed that Mg-ACC was present during the titration of the (Ca,Mg)Cl2 solution (Table 2).
232
After about 50 min of reaction time the presence of a second v1 band at ~1069 cm-1
233
corresponding to monohydrocalcite was observed in the in situ Raman spectra (Table 2). Similar
234
results were obtained by ATR-FTIR analysis, showing the characteristic vibration bands of
235
monohydrocalcite beside the vibration bands of ACC after 60 min of reaction time (Table 2).
236
After 180 min of reaction time only vibration bands of monohydrocalcite and a weak band at
237
1088 cm-1 were observed in ATR-FTIR spectra (Table 2). The XRD pattern showed that the dried
238
precipitates produced in experiment MgCa3 at 25 min of reaction time consist of Mg-calcite
239
(Table 3). In contrast, the precipitate collected at 180 min of reaction time consists of
240
monohydrocalcite (87 wt.%) and minor amounts of Mg-calcite (13 wt.%, Table 3). After 1 day of
241
reaction time nesquehonite (13 wt.%) was found in addition to monohydrocalcite (79 wt. %) and
242
Mg-calcite (8 wt. %, Table 3).
243 244
Chemical evolution of the reactive solutions
245
The initial carbonate solutions are characterized by a carbonate alkalinity of 0.99 ±0.02 M at
246
pH 7.8, 1.02 ±0.01 M at pH 8.3 and 1.15 ±0.02 M at pH 8.8. In all experiments, the carbonate
247
alkalinities decreased to a value of 0.11 ±0.03 M during the titration of the (Ca,Mg)Cl2 solutions
248
(Table S2-S4).
249
The titration of the (Ca,Mg)Cl2 solutions into the carbonate buffer solutions caused instant
250
nucleation/precipitation of Ca1-xMgxCO3 within 1 min of reaction time. The [Ca]aq of the reactive
251
solutions did not exceed 0.007 M during all experimental runs (Table S1-4). After 25 min of
252
reaction time about 98 % of the nCaadd was removed from the reactive solutions due to mineral
253
precipitation. The temporal evolution of the [Mg]aq of the reactive solutions of experiments 11 ACS Paragon Plus Environment
Crystal Growth & Design
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 12 of 32
254
conducted at pH 8.3 and 8.8 is displayed in Figure 3A-B, while the obtained [Mg]aq values of
255
experiment MgCa3 are displayed in Figure S4A. The [Mg]aq of the reactive solutions increased
256
during the titration of the (Ca,Mg)Cl2 solutions. In experiments A1 to A3 the [Mg]aq remained
257
nearly constant between 25 min and 1 day of reaction time (Figure 3A), whereas in experiments
258
C2, and C3 a significant decrease of the [Mg]aq (up to 0.015 M) was observed for the same time
259
interval (Figure 3B). In experiments C1 and MgCa3 on the other hand, the [Mg]aq remained
260
constant at 0.026 and 0.036 M , respectively, between 25 and 60 min of reaction time, before it
261
increased to about 0.040 M in both experiments (180 min, Figure 3B and Figure S4A).
262
Subsequently, the [Mg]aq decreased again to 0.019 M and 0.035 M in experiments C1 and
263
MgCa3, respectively, between 180 min and 1 day of reaction time. A similar [Mg]aq trend as in
264
experiment C1 was observed in the replicate experiment C1_2 (Figure 4B).
265 266
Temporal evolution of Mg content in precipitates
267
During the titration of the (Ca,Mg)Cl2 solutions, the [Mg]solid increased in all experiments
268
(Figure 3C-D). The highest [Mg]solid content after 25 min of reaction time was 10.2 ±0.5 mol%
269
present in the solids of experiments A1 and C1. In experiments A2 and C2 the precipitates
270
contained 7.6 ±0.6 mol% Mg, whereas those in experiments A3 and C3 contained 6.7 ±1.2 mol%
271
Mg after 25 min of reaction time. In experiment MgCa3 the [Mg]solid obtained after 25 min of
272
reaction time is 11.4 mol%.
273
In experiments A1 to A3 (Figure 3C), the [Mg]solid remained nearly constant between 25 min
274
and 1 day of reaction time, while in experiments C2 and C3 the [Mg]solid increased significantly
275
between 25 and 60 min of reaction time (Figure 3D). In the case of experiments C1 and MgCa3,
276
the [Mg]solid remained constant between 25 and 60 min of reaction time and then decreased from
277
10 to 4 mol% in experiment C1 (180 min, Figure 3D) and from 12 to 9 mol% in experiment 12 ACS Paragon Plus Environment
Page 13 of 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Crystal Growth & Design
278
MgCa3 (180 min, Figure S4B). However, between 180 min and 1 day of reaction time, the
279
[Mg]solid increased significantly in both experiments (Figure 3D and Figure S4B), which is also
280
the case for the replicate experiment C1_2, where the evolution of the [Mg]solid is similar to
281
experiment C1.
282 283
DISCUSSION
284 285
Effect of pH on the formation of amorphous calcium carbonate
286
The presence of Mg-rich ACC was observed in all experiments conducted at pH 8.8 (e.g.
287
experiment C1 in Figure 1B, Table 2). In contrast, in experiments conducted at pH 7.8 the in situ
288
Raman spectra showed that Mg-calcite is present within 1 min after the onset of the experiments
289
and in absence of an amorphous precursor (e.g. experiment A1 in Figure 1A; Table 2). Note here
290
that the resolution of in situ Raman spectra at the initial stage of the experiments (< 5 min) is low
291
due to the low amount of solid suspended in the reactive solution. Moreover, the Raman v1 band
292
of ACC is significantly broadened compared to that of crystalline CaCO3 owing to its poorly
293
ordered structure.46 Thus, the presence of ACC within this time frame cannot be completely
294
excluded. In order to evaluate the metastability conditions of ACC in the present experiments, the
295
saturation index of the reactive solutions with respect to ACC (SIACC) was calculated according
296
to Eq. (2). Reactive solutions exhibit SIACC slightly above 0 within at least 25 min of reaction
297
time in the experiments conducted at pH 8.8 (Figure 4). In contrast, in experiments conducted at
298
pH 7.8 reactive solutions exhibit SIACC < 0 during the titration of the (Ca,Mg)Cl2 solution (Figure
299
4). The concentrations and activities of the two dissolved inorganic carbon species (e.g. HCO3-
300
and CO32-) depend on the pH of the reactive solution. For example, after 1 min of reaction time in
301
experiments conducted at pH 8.8, the ratio of CO32- to HCO3- activities in the reactive solutions, 13 ACS Paragon Plus Environment
Crystal Growth & Design
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 14 of 32
302
aCO32-/aHCO3-, was ~3·10-2, whereas in experiments conducted at pH 7.8 the aCO32-/ aHCO3- was
303
significant lower at ~3·10-3 (Table S5). In the latter case, Mg-ACC was likely not formed due to
304
the limited concentration and activity of CO32- in the reactive solutions at lower pH (Table S5).
305
The direct formation of Mg-calcite in experiments conducted at pH 7.8 could be followed
306
by SEM images displaying Mg-calcite aggregates of aligned rhombohedral crystals, which are
307
significantly larger in size (Figure 2A-C) compared to the Mg-calcite nanoparticles formed in
308
experiments, where Mg-ACC transformation was detected (Figure 2H-I). These polycrystalline
309
Mg-calcite aggregates (Figure 2A-C) were likely formed via a spherulitic growth mechanism,
310
where the spherical particles grow from a central nucleation site or seed by incorporation of ions
311
from the solution48. This occurred in experiments A1 to A3 as a consequence of high superstation
312
levels of the reactive solution with respect to calcite (SIcalcite = 1.9 ±0.2 after 1 min of reaction
313
time). In experiment A2 and A3, XRD results indicated the presence of vaterite and aragonite
314
beside Mg-calcite (Table 3). Between 25 min and 1 day of reaction time the proportion of vaterite
315
decreased while the proportion of aragonite increased (Table 3). In most cases, metastable
316
vaterite transforms to calcite via a dissolution-reprecipitation mechanism.32,33,35 In the present
317
study, the ongoing formation of aragonite rather than of Mg-calcite is at first documented at 25°C
318
and is suggested to be caused by the high molar Mg/Ca ratio in the reactive solution after 25 min
319
of reaction time (> 46), inhibiting calcite formation.49-51
320 321
Effect of pH and aqueous Mg2+/Ca2+ ratio on the transformation pathways of ACC
322
The experimental results revealed two pathways of Mg-ACC transformation in the
323
reactive solutions (Figure 5A). Mg-ACC transformed into (i) Mg-calcite in experiments
324
conducted at pH 8.3 with the Mg/Ca ratios of 1/6 to 1/4 (exp. MgCa4, MgCa5 and MgCa6
325
conducted by Purgstaller et al.40) as well as in experiments conducted at pH 8.8 with the Mg/Ca 14 ACS Paragon Plus Environment
Page 15 of 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Crystal Growth & Design
326
ratios 1/6 and 1/8 (exp. C2 and C3), and (ii) monohydrocalcite in experiments conducted at pH
327
8.3 and 8.8 with the Mg/Ca ratios 1/3 (exp. MgCa3) and 1/4 (exp. C1), respectively. Note that in
328
experiment MgCa3 small amounts of Mg-calcite (13 wt. %) were detected beside
329
monohydrocalcite (Table 3).
330
It has been recently suggested that the crystalline phase forming from ACC is defined by
331
the Mg/Ca ratio of the initial solution: ACC with 10 mol% Mg precipitated from a solution with
332
an initial Mg/Ca ratio of 1/9 crystallized to Mg-calcite,32 whereas ACC with 30 mol% Mg
333
precipitated from a solution with an initial Mg/Ca ratio of 3/7 crystallized to
334
monohydrocalcite.38A different pattern is documented in experiments of the present study
335
conducted with the initial Mg/Ca ratio of 1/4 (exp. MgCa4 and C1). Although in both
336
experiments formed ACC has a similar Mg content (10.1 ±0.2 mol% Mg), the in situ Raman
337
spectroscopy revealed the formation of Mg-calcite in experiment MgCa4 and of
338
monohydrocalcite in experiment C1. The formation of monohydrocalcite versus Mg-calcite from
339
Mg-ACC could be attributed to the higher pH of the reactive solution in experiment C1 (pH 8.8)
340
compared to that in experiment MgCa4 (pH 8.3, Figure 5A). However, considering that
341
monohydrocalcite was formed at pH 8.8 only in the experiment conducted with the highest initial
342
Mg/Ca ratio (exp. C1, Figure 5A), a coupled effect of pH and aqueous Mg concentration on the
343
transformation pathways of Mg-ACC is indicated.
344
In the experiments conducted in this study at the end of the (Ca,Mg)Cl2 solution titration
345
and before the transformation of the amorphous to the crystalline phase took place, the ratio of
346
the Ca2+ to CO32- activities in the reactive solution, aCa2+/aCO32-, is lower (0.2 ±0.1) in experiments
347
conducted at pH 8.8 compared to that in experiments conducted at pH 8.3 (1.7 ±0.4, Figure 5B).
348
In the latter case, the aCO32- is lower, owing to the predominance of aqueous HCO3- versus CO32-
349
ions. In order to maintain a solution that is saturated with respect to ACC, the aCa2+ is thus higher 15 ACS Paragon Plus Environment
Crystal Growth & Design
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 16 of 32
350
at pH 8.3 than at pH 8.8 (Figure 5B). This affects the prevailing ratio of Mg2+ to Ca2+ activities in
351
the reactive solution after Mg-ACC was synthesized (aMg2+/aCa2+, Figure 5C). For example,
352
although the initial Mg/Ca ratio was similar in both experiments, the aMg2+/aCa2+ is significantly
353
higher in experiment C1 compared to that in experiment MgCa4 after 25 min of reaction time
354
(Figure 5C), due to the lower aCa2+ at high versus low pH (Figure 5B). Overall, the results
355
obtained revealed that in experiments where Mg-ACC transformed to Mg-calcite (exp. MgCa4,
356
C2 and C3), the aMg2+/aCa2+ is significant lower compared to that in experiment C1, where
357
transformation of Mg-ACC to monohydrocalcite was observed (Figure 5C). In experiment
358
MgCa3, where Mg-ACC transformed to monohydrocalcite and Mg-calcite (13 wt.%), the
359
aMg2+/aCa2+ is equal to 8 and this value likely defines the boundary conditions for the
360
transformation of Mg-ACC to either Mg-calcite or monohydrocalcite (Figure 5C). These
361
observations suggest that the formation of the distinct crystalline phase is controlled by the
362
prevailing aMg2+/aCa2+ of the reactive solution after Mg-ACC was formed: Mg-ACC transformed
363
to (i) Mg-calcite at 5 ≤ aMg2+/aCa2+ ≤ 8 and to (ii) monohydrocalcite at 8 ≤ aMg2+/aCa2+ ≤ 12.
364 365
Mechanism of Mg-calcite and monohydrocalcite formation via metastable ACC
366
The experiments conducted in this study document that the reactive solutions are slightly
367
supersaturated with respect to ACC up to at least 25 min of reaction time (Figure 4). During this
368
timeframe, the reactive solutions are highly supersaturated with respect to calcite (SI ≈ 2.3) and
369
monohydrocalcite (SI ≈ 1.0), which is provoking formation of these phases in the reactive
370
solutions. In experiment C1, the formation of monohydrocalcite instead of thermodynamically
371
more stable calcite can be explained by the inhibition of the latter
372
prevailing aMg2+/aCa2+ (Figure 5C). The inhibiting effect of aqueous Mg2+ is already indicated in 16 ACS Paragon Plus Environment
49-51
due to the elevated
Page 17 of 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Crystal Growth & Design
373
experiment MgCa3, where only small amounts of Mg-calcite were formed besides
374
monohydrocalcite (Table 3). As soon as precipitation of a less soluble crystalline phase (Mg-
375
calcite and/or monohydrocalcite) takes place, the solution reaches undersaturation with respect to
376
ACC (Figure 4). Thus, it is likely that the transformation of the amorphous to the crystalline
377
phase occurred via a dissolution- and re-precipitation mechanism. This mechanism is further
378
supported by the observation that Mg ions are released into the reactive solution throughout Mg-
379
ACC transformation to monohydrocalcite (exp. C1 and C1_2, between 60 and 180 min in Figure
380
3B). In this context, the Mg content of the solid decreased significantly from 10 to 4 mol%,
381
which strongly suggests a partial dissolution/re-precipitation of Mg-rich ACC (Figure 3 D). The
382
prevailing aMg2+/aCa2+ ratio of the reactive solutions and thus the formation of Mg-calcite or
383
monohydrocalcite are suggested to determine the period of Mg-ACC metastability in the reactive
384
solutions (tACC). As it can be seen in Figure 5D, tACC is longer in experiments where
385
monohydrocalcite formation was observed (at higher aMg2+/aCa2+) compared to experiments with
386
Mg-calcite as the reaction product (at lower aMg2+/aCa2+). In that sense, it has been documented
387
that elevated Mg contents in ACC increase the metastability of the amorphous phase in a
388
solution.26,32,40 In contrast, results of the present study showed that the tACC is much longer in
389
experiment C1 (~58 min) compared to that in experiment MgCa4 (~34 min) (Figure 5D),
390
although the Mg content of ACC is about the same in both experiments (10.1 ±0.2 mol%). It is
391
concluded that the metastability of the amorphous phase in the reactive solution is not determined
392
by its Mg content, but is related to the prevailing aMg2+/aCa2+ ratio of the reactive solution and
393
formation behavior of the less soluble crystalline phases, initiating the dissolution of Mg-ACC.
394
Previous experimental studies on calcite formation documented that the nucleation/growth
395
of calcite is retarded at higher aqueous Mg/Ca molar ratios.53-54 Indeed, in the present study,
396
transformation of Mg-ACC to Mg-calcite was observed earlier in reactive solutions at low 17 ACS Paragon Plus Environment
Crystal Growth & Design
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 18 of 32
397
compared to high aMg2+/aCa2+ ratios (Figure 5D). Moreover, the in situ Raman results obtained in
398
our previous study40 showed that the time of Mg-ACC transformation to Mg-calcite is delayed
399
when higher Mg/Ca ratios in the (Ca,Mg)Cl2 solution were used: at initial Mg/Ca ratios of 1/6,
400
1/5, and 1/4 the transformation of Mg-ACC to Mg-calcite was observed after about 15, 25 and 36
401
min of reaction time, respectively. We attributed the prolonged presence of Mg-ACC in the
402
reactive solution to its higher Mg content, but it could also be explained by retarded formation
403
kinetics of Mg-calcite at higher Mg concentrations in the reactive solution. In experiment C1, the
404
presence of Mg-ACC is prolonged due to (i) the inhibition of calcite formation by high
405
aMg2+/aCa2+ values (Figure 5D) and (ii) the slow formation kinetics of monohydrocalcite. Distinct
406
precipitation rates can be followed by in situ Raman spectroscopy, where the formation of
407
monohydrocalcite required ~ 25 min in experiment C1 (Figure 1B). In contrast, the formation of
408
Mg-calcite is significantly faster (~ 8 min, exp. C3 in Figure S3; cf. Purgstaller et al.40).
409
Evidence for the control of the fluid composition (i.e. aqueous Mg/Ca ratio) on the
410
formation of Mg-calcite or monohydrocalcite from Mg-ACC comes also from X-ray diffraction
411
results. Our findings showed that Mg-ACC separated rapidly from reactive solutions of
412
experiments C1 and MgCa3 by membrane filtration transformed to Mg-calcite under air exposure
413
(Table 3), despite the fact that the same Mg-ACC transformed to monohydrocalcite when it
414
remained in the reactive solutions (e.g. exp. C1 in Figure 1B). Under ambient atmospheric
415
conditions H2O molecules are adsorbed onto the ACC phase, forming a water layer, which
416
promotes its dissolution and re-precipitation52,55. The only source of cations in this water layer is
417
that released during the dissolution of Mg-ACC. In the present case, the [Mg]aq/[Ca]aq ratio of the
418
water layer is most likely close to that of the Mg-ACC; in experiments C1 and MgCa3 the Mg/Ca
419
of Mg-ACC is 1/9 and 1/8, respectively. These values are much lower compared to those in the
420
reactive solutions of experiments C1 ([Mg]aq/[Ca]aq = 9/1) and MgCa3 ([Mg]aq/[Ca]aq = 6/1), 18 ACS Paragon Plus Environment
Page 19 of 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Crystal Growth & Design
421
inducing nucleation and growth of Mg-calcite rather than monohydrocalcite. The different
422
reaction products observed during the transformation of the same Mg-ACC precursor either in
423
contact with a reactive fluid or in air indicate that the crystallization of Mg-ACC in our
424
experiments is significantly affected by the physicochemical conditions of the transformation
425
environment (prevailing [Mg]aq/[Ca]aq ratio of the fluid, ions released during Mg-ACC
426
dissolution etc.) and to a lesser extent by a potential proto-crystalline pre-structuring34 of the
427
primary Mg-ACC.
428 429
SUMMARY AND CONCLUSIONS
430
Despite the fact that Mg-rich amorphous calcium carbonate was precipitated at
431
different pH values (8.3 to 8.8) and initial Mg/Ca ratios (1/3 to 1/8) our findings revealed
432
two pathways of Mg-ACC transformation in aqueous solution, which strictly depend on the
433
prevailing aMg2+/aCa2+ of the reactive solution after Mg-ACC was synthesized: (i) at 5 ≤
434
aMg2+/aCa2+ ≤ 8 Mg-calcite is formed via intermediate Mg-ACC. (ii) Conversely, at 8 ≤
435
aMg2+/aCa2+ ≤ 12, Mg-ACC transformed to monohydrocalcite.
436
Independent of the Mg content in ACC, the in situ Raman monitoring indicated a
437
significantly extended metastability of Mg-ACC in the reactive solution in experiments
438
where Mg-ACC transformed to monohydrocalcite at higher aMg2+/aCa2+ (~ 58 min) compared
439
to experiments where Mg-ACC transformed to Mg-calcite at lower aMg2+/aCa2+ (~ 36 min).
440
Moreover, the formation of monohydrocalcite is shown to be a slow process (~ 25 min),
441
whereas the formation of Mg-calcite was comparable fast (~ 8 min). These observations
442
suggest that the formation time of the less soluble crystalline phase formed under the
443
prevailing physicochemical condition of the reactive solution is the rate-limiting process in
19 ACS Paragon Plus Environment
Crystal Growth & Design
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
444
the dissolution/transformation of Mg-ACC. At higher aMg2+/aCa2+ the presence of Mg-ACC in
445
the reactive solution is prolonged due to the inhibition of calcite formation and the slow
446
precipitation kinetics of monohydrocalcite. Our experimental results documented a different
447
transformation product when Mg-ACC was separated from the Mg-rich reactive solution. In
448
this case, the formation of the crystalline phase is determined by the ions released through
449
Mg-ACC dissolution in present adsorbed water layer under atmospheric conditions. These
450
observations clearly highlight the importance of the physicochemical conditions of the
451
transformation environment on the formation of distinct crystalline carbonate phases via
452
metastable Mg-ACC.
Page 20 of 32
453 454
ACKNOWLEDGEMENTS
455
We acknowledge Andrea Wolf, Judith Jernej and Andre Baldermann for their support with the
456
analytical work. Chemical analyses were conducted at NAWI Graz Central Lab for Water,
457
Minerals and Rocks. We would like to thank Gerald Auer and Patrick Grunert for their support in
458
conducting SEM images. This study benefited from the enlightening comments of Jacques Schott
459
and Pascale Bénézeth. Finally, the authors thank Stephan Sacher (Research Center
460
Pharmaceutical Engineering) for providing access to in situ Raman spectroscopy. This work has
461
been financially supported by DFG collaborative research initiative 1644 CHARON (IM44/10-1)
462
and by NAWI Graz.
463 464
SUPPORTING INFORMATION DESCRIPTION
465
Table S1 to S4: Chemical composition of the reactive solutions and solids at certain reaction
466
times from all experiments; Figure S1: The calculated [Mg]solid values obtained from Eq. 1
467
plotted against the Mg contents of the bulk digested solids; Figure S2: additional SEM 20 ACS Paragon Plus Environment
Page 21 of 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Crystal Growth & Design
468
images from experiment A3 and C1; Figure S3: in situ Raman spectra of experiment C3;
469
Figure S4: Mg concentration of the reactive solution and Mg content of the precipitated solid
470
versus the experimental run time of experiment MgCa3.
471 472
REFERENCES
473
(1) Lowenstam, H. A. Science 1981, 211, 1126-1131.
474
(2) Ito, T. J. Mineral. Petrol. Econ. Geol. 1993, 88, 485–491.
475
(3) Buchardt, B.; Israelson, C.; Seaman, P; Stockmann, G. Journal of Sedimentary Research
476
2001, 71, 176-189.
477
(4) Lu, Z.; Rickaby, R. E. M.; Kennedy, H.; Kennedy, P.; Pancost, R. D.; Shaw, S.; Lennie, A.;
478
Wellner, J.; Anderson, J. B. Earth and Planetary Science Letters 2012, 325-326, 108-115.
479
(5) Morse, J. W; Mackenzie, F. T. Develop. Sed. 1990, 48, 707.
480
(6) Mackenzie, F. T.; Bischoff, W. B.; Bishop, F. C.; Loijens, M.; Schoonmaker, J.; Wollast, R;
481
In Carbonates, Mineralogy and Chemistry; Reeder R. J.; Mineral. Soc. America: Chelsea,
482
MI, 1983, Vol 11, pp. 97–144.
483
(7) Long, X.; Ma, Y; Qi, L. (2011) Cryst. Growth Des. 11, 2866-2873.
484
(8) Krukenberg, C. F. W. Vergleichende physiologische Studien 1982, 2, 92-93.
485
(9) Minchin, E. A. Quart. J. micr. Sci. 1898, 40, 469–588.
486
(10) Beniash, E.; Aizenberg, J.; Addadi, L.; Weiner, S. Proc. R. Soc. Lond. B 1997, 264, 461-465.
487
(11) Politi, Y.; Arad, T.; Klein, E.; Weiner, S.; Addadi, L. Science 2004, 306, 1161-1164
488
(12) Hasse, B.; Ehrenberg, H.; Marxen, J. C.; Becker, W.; Epple, M; Chem. Eur. J. 2000, 6, 3679.
489
(13) Khairoun, I.; Magne, D.; Gauthier, O.; Bouler, J. M.; Aguado, E.; Daculsi, G.; Weiss, P.; J.
490 491 492 493 494
Biomed. Mat. Res. 2002, 60, 633-642 (14) Jacob, D. E.; Soldati, A. L.; Wirth, R.; Huth, J.; Wehrmeister, U; Hofmeister, W. Geochimica et Cosmochimica acta 2008, 72, 5401-5415 (15) Griesshaber, E.; Kelm, K.; Sehrbrock, A.; Mader, W.; Mutterlose, J.; Brand, U.; Schmahl, W.W. European Journal of Mineralogy 2009, 21, 715-723.
495
(16) Aizenberg, J.; Lambert, G.; Weiner, S.; Addadi, L. J Am Chem Soc. 2002, 124, 32–9.
496
(17) Sethmann, I.; Hinrichs, R.; Wörheide, G.; Putnis, A. J. Inorg. Biochem. 2006, 100, 88–96.
497
(18) Tao, J.; Zhou, D.; Zhang, Z.; Xu, X.; Tang, R. PNAS 2009, 106, 22096–22101. 21 ACS Paragon Plus Environment
Crystal Growth & Design
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
498 499
Page 22 of 32
(19) Couradeau, E.; Benzerara, K.; Gérard, E.; Moreira, D.; Bernard, S.; Brown, G.E. Jr.; LópezGarcía, P. Science 2012, 336, 459-462
500
(20) Jaquet, J.-M.; Nirel, P; Martignier, A. J. Limnol. (2013) 73, 592-605
501
(21) Demény, A.; Czuppon, G.; Kern, Z.; Leél-Ossy, S.; Németh, A.; Szabó, M.; Tóth, M.; Wu,
502
C-.C.; Shen, C.-C.; Molnár, M.; Németh, T.; Németh, P.; Óvári, M. Quaternary
503
International 2016, 415, 25-32
504 505 506 507
(22) Meiron, O. E.; Bar-David, E.; Aflalo, E. D.; Shechter, A.; Stepensky, D.; Berman, A.; Sagi, A. J. Bone Miner. Res. 2011, 26 (2), 364–372. (23) Zhao, Y.; Luo, Z.; Li, M.; Qu, Q.; Ma, X.; Yu, S.-H.; Zhao, Y. Angew. Chemie Int. Ed. 2015, 54 (3), 919–922.
508
(24) Brečević, L; Nielsen, A. E. Journal of Crystal Growth 1989, 98, 504-510.
509
(25) Raz, S.; Hamilton, P. C.; Weiner, S.; Addadi, L. Adv. Funct. Mater. 2003, 13, 480-486.
510
(26) Loste, E.; Wilson, R. M.; Seshadri, R; Meldrum, F. C. Journal of Crystal Growth 2003, 254,
511 512 513
206-218. (27) Lam, R. S. K.; Charnock, J. M.; Lennie, A.; Meldrum, F. C. CrystEngComm 2007, 9, 12261236
514
(28) Han, T. Y.-J.; Aizenberg, J. Chemistry of Materials 2008, 20(3), 1064-1068.
515
(29) Politi, Y.; Batchelor, D. R.; Zaslansky, P.; Chmelka, B. F.; Weaver, J. C.; Sagi, I.; Weiner,
516 517 518 519 520 521 522
S. Addadi, L. Chem. Mater. 2010, 22, 161–166. (30) Mavromatis, V.; Schmidt, M.; Botz, R.; Comas-Bru, L.; Oelkers, E. H. Chem. Geol. 2012, 310–311, 97–105. (31) Radha, A. V.; Fernandez-Martinez, A.; Hu, Y.; Jun, Y.; Waychunas, G. A.; Navrotsky A. Geochim. Cosmochim. Acta 2012, 90, 83-95. (32) Rodriguez-Blanco, J. D.; Shaw, S.; Bots, P.; Roncal-Herrero, T., Benning, L. G. Journal of Alloys and Compounds 2012, 536S, 477-479.
523
(33) Ogino, T.; Suzuki, T.; Sawada, K. Geochim. Cosmochim. Acta 1987, 51, 2757-2767.
524
(34) Gebauer, D.; Völkel, A.; Cölfen, H. Science 2008, 322, 1819-1822
525
(35) Bots, P.; Benning, L. G.; Rodriguze-Blanco, J. D.; Roncal-Herrero, T.; Shaw, S. Crys.
526
Growth Des. 2012, 12, 3806-3814
527
(36) Kimura, T.; Koga, N. Cryst. Growth. Des. 2011, 11, 3877-3884
528
(37) Nishiyama, R.; Munemoto, T.; Fukushi, K. Geochimica et Cosmochimica Acta 2013, 100,
529
217-231 22 ACS Paragon Plus Environment
Page 23 of 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
530 531 532 533 534 535 536 537 538 539
Crystal Growth & Design
(38) Rodriguez-Blanco, J. D.; Shaw, S.; Bots, P.; Roncal-Herrero, T.; Benning, L. G. Geochim. Cosmochim. Acta 2014 127, 204-220 (39) Rodriguez-Navarro, C; Kudlacz, K.; Cizer, Ö.; Ruiz-Agudo, E. CrystEngComm 2015, 17, 58-72 (40) Purgstaller, B.; Mavromatis, V.; Immenhauser, A.; Dietzel, M. Geochim. Cosmochim. Acta 2016, 174, 180-195 (41) Bischoff, W. D.; Sharma, S. K.; MacKenzie, F. T. American Mineralogist 1985, 70, 581589. (42) Edwards, H. G. M.; Villar, S. E. J.; Jehlicka, J.; Munshi, T. Spectrochimica Acta 2005, Part A 6, 2273-2280.
540
(43) Böttcher, M. E.; Gehlken, P.-L.; Steele, D. F. Solid State Ionics 1997, 101-103, 1379-1385.
541
(44) Kontoyannis, C. G.; Vagenas, V. Analyst 2000, 125, 251-255
542
(45) Wang, D.; Hamm, L. M.; Bodnar, R. J.; Dove, P. M.; J. of Raman Spectrosc. 2012, 43, 543-
543 544 545
548. (46) Coleyshaw, E. E.; Crump, G.; Griffith, W. P. Spectrochimica Acta 2003, Part A 59, 22312239
546
(47) Neumann, M.; Epple M. Eur. J. Inorg. Chem. 2007, 1953-1957
547
(48) Andreassen, J.-P.; Flaten, E. M.; Beck, R; Lewis, A. E. Chemical Engineering Research and
548
Design 2010, 88, 1163-1168
549
(49) Lippmann F. (1973) Sedimentary carbonate minerals. Springer, Berlin.
550
(50) Falini, G., Gazzano, M., Ripamonti, A., 1994. Crystallization of calcium carbonate in
551 552 553
presence of magnesium and polyelectrolytes. Journal of Crystal Growth 137, 577–584. (51) Fernández-Díaz, L., Putnis, A., Prieto, M., Putnis, C.V., 1996. Journal of Sedimentary Research 66, 482–491
554
(52) Xu, X.; Han, J. T.; Kim, D. H.; Cho, K. J. Phys. Chem. B 2006, 110, 2764-2770
555
(53) Fernández-Díaz, L.; Putnis, A.; Prieto, M.; Putnis, C.V. Journal of Sedimentary Research,
556
1996, 66, 482–491
557
(54) Niedermayr, A.; Köhler, S. J; Dietzel M. Chem. Geol. 2013, 340, 105–120
558 559
(55) Konrad, F.; Gallien, F.; Gerard D. E.; Dietzel M. Crystal Growth & Design, 2016, 63106317
23 ACS Paragon Plus Environment
Crystal Growth & Design
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
560
Page 24 of 32
For Table of Contents Use Only
561
Control of Mg2+/Ca2+ activity ratio on the formation of crystalline carbonate
562
minerals via an amorphous precursor
563
Bettina Purgstaller1, Florian Konrad1, Martin Dietzel1, Adrian Immenhauser2, Vasileios Mavromatis1,3
564
1
Institute of Applied Geosciences, Graz University of Technology, Rechbauerstrasse 12, 8010 Graz, Austria
565
2
Institute of Geology, Mineralogy and Geophysics, Bochum, Universitätsstraße 150, 44801 Bochum, Germany
566
3
Géosciences Environnement Toulouse, CNRS, UMR5563, Avenue Edouard Belin 14, 31400 Toulouse, France
567 568
Mg-rich amorphous calcium carbonate that was sampled during the experimental
569
runs did not remain stable after sample filtration and altered to Mg-calcite under air
570
exposure. A different pattern was documented when Mg-ACC transformed in the
571
reactive solutions. Although precipitating Mg-ACC with a similar Mg content of 10
572
mol%, the experimental results revealed two pathways of Mg-ACC depending on
573
the prevailing ratio of Mg2+ to Ca2+ activities, aMg2+/aCa2+, in the reactive solution.
574 575 24 ACS Paragon Plus Environment
Page 25 of 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Crystal Growth & Design
576
Table 1
577
Initial compositions of the experimental solutions for ACC (trans)formation. Mg/Ca denotes
578
molar ratio referred to total concentration (Mg + Ca) of 0.6 M. Experiment A1 A2 A3 C1 C1_2 C2 C3 MgCa3
pH 7.8 7.8 7.8 8.8 8.8 8.8 8.8 8.3
Mg/Ca 1/4 1/6 1/8 1/4 1/4 1/6 1/8 1/3
579
25 ACS Paragon Plus Environment
Crystal Growth & Design
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 26 of 32
580
Table 2
581
Frequencies (cm-1) of observed carbonate vibration bands from in situ Raman and ATR-FTIR
582
spectra and identified mineralogy of the precipitates at certain reaction times. Note that in
583
experiment MgCa3 in situ Raman spectra of reactive solution were not obtained after 60 min
584
(n.a.). Mg-Cc: Mg-calcite, Arg: aragonite, Vtr: vaterite, Mhc: monohydrocalcite, Nesq:
585
nesquehonite. Experiment
time
Raman v1
A1
A2
A3
C1
C2
C3
MgCa3
13 min 25 min 60 min 180 min 1d 13 min 25 min 60 min 180 min 1d 13 min 25 min 60 min 180 min 1d 13 min 25 min 60 min 180 min 1d 13 min 25 min 60 min 180 min 1d 13 min 25 min 60 min 180 min 1d 13 min 25 min 60 min 180 min 1d
1088 1088 1088 1088 1088 1087 1087 1087 1086 1086 1087 1087 1087 1086 1086 1083 1083 1083/1068 1068 1100/1068 1081 1081 1087 1088 1088 1082 1082 1088 1088 1088 1082 1083 1083/1069 n.a. n.a
Mineralogy libration mode 282 283 283 283 283 283 283 283 283/205 283/205 282 282 282 282/205 282/205 282 283 283 282 282 282 n.a. n.a.
Mg-Cc Mg-Cc Mg-Cc Mg-Cc Mg-Cc Mg-Cc Mg-Cc Mg-Cc Mg-Cc, Arg Mg-Cc, Arg Mg-Cc Mg-Cc Mg-Cc Mg-Cc, Arg Mg-Cc, Arg Mg-ACC Mg-ACC Mg-ACC, Mhc Mhc Mhc, Nesq Mg-ACC Mg-ACC Mg-Cc Mg-Cc Mg-Cc Mg-ACC Mg-ACC Mg-Cc Mg-Cc Mg-Cc Mg-ACC Mg-ACC Mg-ACC, Mhc n.a n.a
v1
ATRFTIR v2
v4
1082 1083 1083 1083 1083 1082 1082 1083 1082 1083 1082 1082 1082 1082 1082 1073 1074 1073 1068 1068 1072 1074 1085 1085 1083 1073 1073 1084 1084 1084 1073 1073 1073 1068/1088 1068/1088
870 870 871 870 870 871 870 870/856 870/855 871/855 871 870/856 870/856 870/855 870/854 860 860 870 /860 870 871 860 860 871 870 870 861 860 871 871 871 860 859 871/860 870 872
713 713 712 712 712 743/712 743/712/700 712/700 711/700 712/700 743/712 743/712/699 743/712/699 743/712/699 712/699 697 753/726/697 751/726/697 711 712 711 712 712 712 697 755/727/697 761/728/699
586 587 26 ACS Paragon Plus Environment
Mineralogy
Mg-Cc Mg-Cc Mg-Cc Mg-Cc Mg-Cc Mg-Cc, Vtr Mg-Cc, Arg, Vtr Mg-Cc, Arg Mg-Cc, Arg Mg-Cc, Arg Mg-Cc, Vtr Mg-Cc, Vtr, Arg Mg-Cc, Vtr, Arg Mg-Cc, Vtr, Arg Mg-Cc, Arg Mg-ACC Mg-ACC Mg-ACC, Mhc Mhc Mhc Mg-ACC Mg-ACC Mg-Cc Mg-Cc Mg-Cc Mg-ACC Mg-ACC Mg-Cc Mg-Cc Mg-Cc Mg-ACC Mg-ACC Mg-ACC, Mhc Mhc, Mg-Cc Mhc, Mg-Cc
Page 27 of 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Crystal Growth & Design
588
Table 3
589
Mineralogical composition from XRD-patterns of precipitates sampled at certain reaction times.
590
The compositions refer to precipitates, which are completely transformed to crystalline solids
591
after sampling. Quantifications were realized by Rietveld refinement. Mg-Cc: Mg-calcite, Arg:
592
aragonite, Vtr: vaterite; Mhc: monohydrocalcite; Nesq: nesquehonite. Experiment A1
A2
A3
C1
C2
C3
MgCa3
time min/d 25 min 180 min 1d 25 min 180 min 1d 25 min 180 min 1d 25 min 180 min 1d 25 min 180 min 1d 25 min 180 min 1d 25 min 180 min 1d
Mg-Cc wt. % 97 96 95 74 72 75 61 61 61 100 100 100 100 100 100 100 100 13 8
Arg wt. % 3 4 5 13 18 25 18 24 33 -
Vtr wt. % 14 9 21 15 6 -
593
594
27 ACS Paragon Plus Environment
Mhc wt. % 100 86 87 79
Nesq wt. % 14 13
Crystal Growth & Design
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 28 of 32
595
596 597
Figure 1. Waterfall plot of in situ Raman spectra showing the vibration band of aqueous HCO3-
598
and CO32- as well as of v1 band of CO32- related to Mg-ACC, Mg-calcite (Mg-Cc) and
599
monohydrocalcite (Mhc) and ATR-FTIR spectra of precipitates sampled during certain reaction
600
times of the experiment A1 (A) and C1 (B).
28 ACS Paragon Plus Environment
Page 29 of 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Crystal Growth & Design
601 602
Figure 2. SEM images of precipitates sampled after 1 day of reaction time from experiments of
603
the present study and from experiments MgCa4, MgCa6 and MgCa8 of Purgstaller et al.40
604
showing Mg-calcite (Mg-Cc), aragonite (Arg) and monohydrocalcite (Mhc) crystals.
605 606 607 608 609
29 ACS Paragon Plus Environment
Crystal Growth & Design
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 30 of 32
610 611
Figure 3. (Left) Concentration of dissolved Mg ions of the reactive solution, [Mg]aq, versus
612
experimental run time of experiments conducted at pH 7.8 (A) and pH 8.8 (B). (Right) Mg
613
content of the precipitated solid, [Mg]solid, calculated according to Eq. 1 versus experimental run
614
time of experiments conducted at pH 7.8 (C) and pH 8.8 (D). Titration of the (Ca,Mg)Cl2
615
solutions into the NaHCO3 solutions was stopped at 25 min of experimental time (dashed line).
616
When not visible, error bars are smaller than the symbols.
617 618
30 ACS Paragon Plus Environment
Page 31 of 32
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Crystal Growth & Design
619 620
Figure 4. Evolution of the saturation index with respect to ACC (SIACC) over the experimental
621
time of the reactive solutions of experiments conducted at pH 7.8 (exp. A1 to A3), and 8.8 (exp.
622
C1 to C3).
623
31 ACS Paragon Plus Environment
Crystal Growth & Design
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 32 of 32
624 625
Figure 5. (A) Pathways of Mg-ACC transformation in the reactive solutions depending on pH
626
and initial Mg/Ca ratio. (B) Activities of Ca2+ and CO32- in reactive solutions after the titration of
627
the (Ca,Mg)Cl2 solution was stopped and before transformation of the amorphous to the
628
crystalline phase took place. (C) Initial Mg/Ca ratio versus the prevailing ratio of Mg2+ to Ca2+
629
activities of reactive solutions, aMg2+/aCa2+, after the titration of the (Ca,Mg)Cl2 solution was
630
stopped and before the transformation of the amorphous to the crystalline phase took place (D)
631
Reaction time at which Mg-ACC transformation was indicated by in situ Raman spectroscopy
632
(tACC) versus aMg2+/aCa2+. Note that, except for experiment MgCa4, the aMg2+/aCa2+ values obtained
633
in experiments MgCa5 and MgCa6 conducted at pH 8.3 by Purgstaller et al.40 could not be
634
displayed in Figure 5C-D because the transformation of crystalline carbonate minerals took place
635
before the titration of the (Mg,Ca)Cl2 solution was stopped.
636
32 ACS Paragon Plus Environment