Dual Amplified Electrochemical Immunosensor for Highly Sensitive

Nov 10, 2014 - Electrochemical Immunosensors. Kuldeep Mahato , Suveen Kumar , Ananya Srivastava , Pawan K. Maurya , Renu Singh , Pranjal Chandra...
0 downloads 0 Views 1MB Size
Subscriber access provided by ONDOKUZ MAYIS UNIVERSITESI

Article

Dual amplified electrochemical immunosensor for highly sensitive detection of Pantoea stewartii sbusp. stewartii Yuan Zhao, Liqiang Liu, Dezhao Kong, Hua Kuang, Libing Wang, and Chuanlai Xu ACS Appl. Mater. Interfaces, Just Accepted Manuscript • Publication Date (Web): 10 Nov 2014 Downloaded from http://pubs.acs.org on November 11, 2014

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

ACS Applied Materials & Interfaces is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 26

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

Dual amplified electrochemical immunosensor for highly sensitive detection of Pantoea stewartii sbusp. stewartii Yuan Zhao1,2, Liqiang Liu1, Dezhao Kong1, Hua Kuang1*, Libing Wang1, Chuanlai Xu1 1

State

Key

Lab

of

Food

Science

and

Technology, School

of

Food

Science

and

Technology,

Jiangnan University, Wuxi, Jiangsu, 214122, PRC 2

The Key Lab of Food Colloids and Biotechnology, Ministry of Education, School of Chemical and Materials

Engineering, Jiangnan University, Wuxi, Jiangsu, 214122, PRC

ABSTRACT: Accurate and highly sensitive detection of Pantoea stewartii sbusp. stewartii-NCPPB 449 (PSS) is urgently required for international shipments due to tremendous agricultural economic losses. Herein, dual amplified electrochemical sandwich immunosensor for PSS detection was developed, utilizing the good specificity and low cost of electrochemical immunoassay, the favorable conductivity and large specific surface area of gold nanoparticles (Au NPs), and the excellent catalytic ability of and horseradish peroxidase (HRP). A linear curve between current response and PSS concentration was established, and the limit of detection (LOD) was 7.8×103 cfu/mL, which is 20 times lower than conventional enzyme-linked immunosorbent assay (ELISA). This strategy is a useful approach for the highly sensitive detection of plant pathogenic bacterium. KEYWORDS: Au NPs, electrochemical, immunosensor, PSS, sensitive detection

1

ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 2 of 26

1. INTRODUCTION PSS is a gram-negative plant pathogenic bacterium which causes Stewart’s vascular wilt in maize, and is classified as a quarantine organism in many countries.1,

2

Due to serious agricultural

economic losses and the potential risk of transmission, a highly sensitive detection method for PSS is critical for international shipments. The main detection methods currently used are microbial assay (MA), ELISA and polymerase chain reaction (PCR).3-5 Although these approaches are well-proven and accepted, complicated operations and false-positive signals as well as the low LODs have restricted the application of MA and ELISA.6 In addition, PCR has high sensitivity, but requires expensive instruments.2, 6 A simple, accurate, highly sensitive and selective assay capable of detecting PSS is necessary for biodefense applications. Electrochemical immunoassay has received more attention in recent years due to its specificity, portability, rapid detection and low cost.7-12 HRP is an excellent electroactive label, which exhibits good stability and solubility, and is commonly introduced to catalyze substrates which produce quantitative electrochemical signals.13-15 The concentration of PSS in maize is generally quite low in the early stage of disease, thus there is a need to acquire amplified electrochemical signals and fabricate a disposable and portable electrochemical immunosensor for on-site monitoring in maize. Electroactive NPs have been successfully produced to amplify the electrochemical signals and improve the sensitivity of electrochemical immunosensors.16-23 Au NPs with favorable conductivity, large specific surface area and high affinity for binding to amino-containing molecules, not only allow the attachment of multiple electroactive labels, but accelerate electron transfer, which generate an amplified electrochemical signal.14,

15, 24-26

In

addition, the excellent biocompatibility of Au NPs retains the biological activity of the antibody, 2

ACS Paragon Plus Environment

Page 3 of 26

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

thus improving the analytical performance of the immunoassay.22, 26-29 In this study, a simple and sensitive electrochemical immunoassay for PSS detection was for the first time developed using Au NPs and HRP for dual signal amplification, without significantly increasing the complexity of the procedures. HRP-labeled anti-PSS detection antibody (D-Ab-HRP) was prepared in comparison to previous reports of complex enzyme-labeled antigen procedures,13 and then was attached to the surface of Au NPs. A sandwich immunosensor of capture anti-PSS antibody (C-Ab), PSS and D-Ab-HRP was established (Scheme 1). The current response of the immunosensors showed a linear relationship with the concentration of PSS which ranged from 2.0×107 cfu/mL to 4.0×104 cfu/mL, and the limit of detection was as low as 0.78×104 cfu/mL (7.8×103 cfu/mL). Dual amplified electrochemical immunoassay took advantages of the extraordinary properties of Au NPs and the catalytic ability of HRP, and achieved accurate and highly sensitive detection of the plant pathogenic bacterium. Scheme 1

2. EXPERIMENTAL SECTION 2.1. Materials and Reagents. Hydroquinone (HQ), p-aminobenzene sulfonic acid and phosphorus pentachloride were purchased from Shanghai Chemical Reagent. Hydrogen tetrachloroaurate trihydrate (HAuCl4·3H2O), sodium citrate and HRP were purchased from Sigma-Aldrich. Bovine serum albumin (BSA) was obtained from Sunshine Biotechnology Co., Ltd. (Nanjing, China). All other chemicals were of analytical grade. Millipore-Q water was obtained using a Milli-Q device (18.2 MΩ, Millipore, Molsheim, France). 2.2. Preparation of D-Ab-HRP Labeled Au NPs. 0.2 mL 10 mg/mL HRP solution was reacted 3

ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

with 0.2 mL 0.06 M NaIO4 at 4°C. After 30 min, 0.2 mL 0.16 M ethylene glycol was added to the mixture and reacted for 30 min at room temperature. 0.2 mg D-Ab was added to the above solution and the pH was carefully adjusted to around 9.0 using 0.05 M carbonate buffer (pH 10.0). After 24 h, 0.08 mL 5 mg/mL NaBH4 solution was added and reacted for 2 h at 4°C. 0.08 mL saturated (NH4)2SO4 solution was added to the mixture and kept at 4°C for 1 h to obtain HRP-conjugated D-Ab. The mixtures were centrifuged at 2400 g for 30 min, and the precipitant was cleaned twice using half-saturated (NH4)2SO4 solution and re-suspended in 0.01 M pH 7.4 PBS solution with the final concentration of D-Ab at 2 µg/mL. The D-Ab-HRP conjugates were dialyzed in 0.01 M pH 7.4 PBS solution for 3 days to remove the dissociative ammonium ions, and were stored at 4°C in the dark. 18 ± 2 nm Au NPs were synthesized by reducing HAuCl4·3H2O with sodium citrate.30-32 4 µL 0.1 M K2CO3 solution was added to 1 mL Au NPs solution, and then D-Ab-HRP solution was injected into the above mixture at the final concentration of 13 nM. After 1 h, 50 µL 10% BSA solution was added and blocked for 1 h. The conjugates were centrifuged at 5400 g for 10 min, and washed twice with PBS solution containing 2% (w/v) BSA, 2% (w/v) sucrose, and 0.02% (w/v) sodium azide. The D-Ab-HRP-Au NPs conjugates were finally re-suspended in 100 µL PBS solution. 2.3. Immobilization of C-Ab onto Glassy Carbon Electrode (GCE). Firstly, the GCE was carefully polished using 0.05 µm alumina slurry and washed with Millipore-Q water, followed sequentially by ultrasonic cleaning in Millipore-Q water and ethanol for 3 min each. The sulfated GCE was treated according to previous methods.24 The GCE was scanned for 30 min in 50 mM p-aminobenzene sulfonic acid solution at 0.1 V/s between -0.5 V and 0.5 V, and then immersed in 4

ACS Paragon Plus Environment

Page 4 of 26

Page 5 of 26

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

50 mM phosphorus pentachloride solution to activate the sulfonic groups, followed by washing and drying. Secondly, 5 µL 10 µg/mL C-Ab was immobilized onto the surface of the GCE at 37°C for 3 h. The C-Ab-GCE was rinsed three times with 0.01 M pH 7.0 PBST solution. Thirdly, 5 µL PBS solution containing 5% BSA was added to the surface of C-Ab-GCE and the redundant sites were blocked at 4°C overnight. The C-Ab-GCE was washed three times with 0.01 M pH 7.0 PBST solution. 2.4. Fabrication of the Electrochemical Immunoassay. For PSS detection, the prepared C-Ab-GCE was immersed in different concentrations of PSS solution and incubated at room temperature for 1 h, followed by rinsing with 0.01 M pH 7.0 PBST solution and drying by N2. Then, 5 µL D-Ab-HRP-Au NPs was added to the surface of the electrode to combine with PSS for 1 h and washed with 0.01 M pH 7.0 PBST solution three times. The sandwich structure of C-Ab-PSS-D-Ab was formed. 8 mL pH 7.0 PBS solution containing the enzymatic substrate of 1.5 mM HQ and 2.0 mM H2O2 was added to the electrolytic cell. The linear sweep voltammetric (LSV) curves of the enzymatic products were recorded. 2.5. Instrumentation and Measurement. Electrochemical measurements and the electrochemical impedance spectroscopy (EIS) were performed on a three-electrode system of the CHI660D electrochemical workstation (Chenhua Instrument Company, Shanghai, China), in which the GCE was the working electrode, the Pt wire was the auxiliary electrode, and a saturated calomel electrode was the reference electrode. EIS was measured in a solution of 5 mM [Fe(CN)6]3- and 0.1 M KCl from 1×105 Hz to 0.1 Hz with a pulse amplitude of 5 mV. The morphology of Au NPs was characterized using a transmission electron microscope (JEOL JEM-2100) operating at an acceleration voltage of 200 kV. UV/vis spectra were measured by a UNICO 2100 PC UV/vis 5

ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

spectrophotometer and processed using Origin Lab software. 3. RESULTS AND DISCUSSION 3.1. Characterization of Au NPs and the Conjugates of D-Ab-HRP-Au NPs. In this study, an anti-PSS detection antibody (D-Ab) and an anti-PSS capture antibody (C-Ab) were prepared and paired in our laboratory. To achieve highly sensitive detection of PSS, Au NPs as the supporter carrying HRP-labeled D-Ab was fabricated.33 As shown in Figure 1, the synthesized Au NPs of 18 ± 2 nm showed good dispersity, unique morphology, and exhibited a localized surface plasmon resonance (LSPR) at 521 nm. D-Ab showed a UV absorption peak at 278 nm, while HRP-labeled D-Ab showed two obvious peaks at 278 nm and 402 nm, illustrating the successful modification of HRP on D-Ab according to the sodium periodate method. For D-Ab-HRP-Au NPs conjugates, not only the UV absorption of D-Ab and HRP was obtained, but also the LSPR of Au NPs occurred to 5 nm red shift. The hydrodynamic sizes of Au NPs after modification showed narrow size distribution (Figure S1). No aggregation was observed from TEM images. These results showed Au NPs possessed well dispersity and good stability which can be served an excellent biocompatible supporter to load D-Ab-HRP on the surface in the application. The average number of HRP-labeled anti-PSS detection antibody on each Au NP was calculated to be 4.1 ± 0.5 (Figure S2). Figure 1

3.2. Optimization of the Experimental Conditions of the Immunoassay. The electrochemical immunoassay depended on the electrochemical features of HRP which catalyzed the oxidation of HQ and H2O2. The enzymatic substrate concentration of HQ and H2O2, the amount of 6

ACS Paragon Plus Environment

Page 6 of 26

Page 7 of 26

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

D-Ab-HRP-Au NPs and the incubation time all had an impact on the current response of the immunosensor. As shown in Figure 2a, under the same concentration of H2O2, D-Ab-HRP-Au and incubation time, the current response of the immunosensor increased with increasing concentration of HQ from 0.5 mM to 1.5 mM and tended to balance from 1.5 mM to 3.0 mM. The optimized concentration of HQ was 1.5 mM. Figure 2b shows the effect of H2O2 concentration on the current response of the immunosensor. 2.0 mM H2O2 was chosen as the optimum concentration at which the maximum current was obtained. In the presence of 1.5 mM HQ and 2.0 mM H2O2, the catalytic current of the electrochemical immunoassay increased with increasing concentration of D-Ab-HRP-Au NPs conjugates from 0.5 µg/mL to 3.0 µg/mL and an increase in incubation time from 20 min to 60 min. However, there were no obvious changes at higher concentrations of D-Ab-HRP-Au NPs conjugates and longer incubation time. Figure 2

3.3. Electrochemical Behaviors of Au NPs Amplified Immunosensors. The interface properties of surface-modified GCE were characterized through monitoring the changes of electron-transfer resistance (Figure S3). In comparison with the small semicircle at high frequencies for bare GCE, C-Ab-GCE exhibited a higher resistance due to the poor conductivity of C-Ab, indicating the successful modification of C-Ab. Similarly, the resistance further increased after PSS combined with C-Ab on the electrode. The insulating C-Ab layer and PSS layer retarded the electron transfer, resulting in even higher resistance. Interestingly, when D-Ab-HRP-Au NPs conjugates was added on GCE surface, the resistance of electrochemical immunosensors was decreased, which was ascribed to the good conductivity for effective electron transfer. 7

ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 3

Under the optimized detection conditions, the oxidation-reduction reaction between HQ and H2O2 catalyzed by HRP was promoted. As shown in the cyclic voltammetry (CV) curve of Figure 3, no redox response was observed for the bare GCE immersed in pH 7.0 PBS solution containing no HQ and H2O2. In comparison to the small redox peaks of the modified GCE immersed in pH 7.0 PBS solution containing 1.5 mM HQ and 2.0 mM H2O2, the modified GCE after incubation with D-Ab-HRP exhibited a higher current response attributed to the excellent catalysis of HRP (Figure S4). When D-Ab-HRP-Au NPs conjugates were immobilized on the surface of the PSS-C-Ab modified GCE, a substantial amplified current response was observed. The mechanism underlying the Au NPs amplified electrochemical signal can be ascribed to the good biocompatibility, excellent electron transfer and the superior specific surface area of Au NPs.15, 22, 24, 25

The favorable conductivity of Au NPs accelerated the electron transfer from enzymatic

substrate to electrode. The high surface-to-volume of Au NPs enriched the amount of D-Ab-HRP, which further promoted the catalytic process and greatly improved the detection sensitivity of the immunoassay for the plant bacterium. However, the peak-to-peak separation showed a slight increase which can be eliminated by optimizing the scanning rates and the concentration of different electrolyte solution, avoiding the polarization of electrodes and faultlessly polishing the electrodes.28, 34, 35 3.4. Analytical Performance of the PSS Electrochemical Immunoassay. A sandwich electrochemical immunoassay which depended on the highly specific molecular affinity of C-Ab, PSS and D-Ab was used to detect PSS. As shown in Figure 4, the linear sweep stripping 8

ACS Paragon Plus Environment

Page 8 of 26

Page 9 of 26

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

voltammetric (LSV) curve of the C-Ab modified GCE after incubation with increasing concentrations of PSS and D-Ab-HRP-Au NPs conjugates showed an enhanced electrocatalytic current response in pH 7.0 PBS solution containing 1.5 mM HQ and 2.0 mM H2O2. A linear plot of the stripping peak current of the immunosensors versus the PSS concentration ranging from 2.0×107 cfu/mL to 4.0×104 cfu/mL was established with a correlation coefficient of 0.993 (Figure 5). The coincident peak potential of the stripping peaks indicated good accuracy and reproducibility of the Au NPs amplified immunoassay. The LOD was down to 7.8×103 cfu/mL which was calculated at a signal-to-noise ratio of 3σ (where σ was the standard deviation of the signal in a blank solution, see Supporting Information). These results indicated that the proposed electrochemical immunoassay for PSS detection was highly sensitive and the detection limit was almost 20 times lower than that with ELISA (1.5×105 cfu/mL). In comparison to other methods depending on fluorescence signal or magnetic relaxation (Table S1), dual amplified electrochemical sandwich immunoassay was free from oxygen, humidity and foreign species, and was simply operated, low cost, accurate and stable. Figure 4 Figure 5

To evaluate the reliability of the Au NPs amplified immunoassay, spiked experiments were performed by quantifying the PSS concentration in corn seed soak solution. The recoveries for the spiked samples ranged from 90.6% to 107.5% (Table 1). The selectivity performance of the immunosensors was studied using another four types of plant pathogenic bacteria at a concentration of 1.0×107 cfu/mL, and included Burkholderia glumae (NCPPB 2391), Rice 9

ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

bacterial leaf streak pathogen (NCPPB 1585), Rice bacterial cercospora leaf spot pathogen (NCPPB 2844) and Crucifer black spot pathogen (NCPPB 1820). As illustrated in Figure 6, the current response of electrochemical immunosensors for the other four target analytes was much smaller than that of PSS, which was mainly due to the weak redox reaction between HQ and H2O2 without the catalysis of HRP. Besides specificity, the regeneration and stability of electrochemical immunosensors were also important criterions in the real applications. The current response of sensors was investigated by detecting three different concentration PSS before and after elution (Figure S5). There were almost no cross-impacts between different concentration of PSS, and the current signal was easily be recovered to the original current response of bare GCE. Furthermore, no obvious changes for CV curves were observed with 2 h to 20 h (Figure S6), illustrating the good stability of electrochemical sensors. These results showed that the Au NPs amplified electrochemical immunoassay has potential in real applications. Figure 6

4. CONCLUSIONS In summary, dual amplified electrochemical immunoassay was developed for highly sensitive detection of PSS, utilizing the favorable conductivity and large specific surface area of Au NPs and the excellent catalytic ability of HRP. With a sandwich enzyme-based immunoassay format, the LOD for PSS detection was down to 7.8×103 cfu/mL, which increased the detection sensitivity by 20-fold compared with conventional ELISA. The biocompatible recognition and amplified signal provides a useful way to fabricate nanomaterials-driven electrochemical immunosensors for the highly sensitive and multiple plant pathogenic bacteria detection, which were critical on the 10

ACS Paragon Plus Environment

Page 10 of 26

Page 11 of 26

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

way for achieving on-site monitoring of maize.

ASSOCIATED CONTENT Supporting Information Hydrodynamic sizes of Au NPs and the conjugates of D-Ab-HRP-Au NPs, Detail calculation of antibody number on Au NPs by UV spectra, Changes of electrochemical impedance spectroscopy of modified electodes, Detail schematic illustration, LSV curves of C-Ab modified GCE for PSS detection, Table of the comparison of LODs based on various methods. This information is available free of charge via the Internet at http://pubs.acs.org/. AUTHOR INFORMATION *

Corresponding Authors: [email protected]

ACKNOWLEDGMENTS This work is financially supported by the Key Programs from MOST (2012BAC01B07, 2012BAK17B10).

11

ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

REFERENCES (1) Roper, M. C., Pantoea Stewartii Subsp. Stewartii: Lessons Learned From a Xylem-dwelling Pathogen of Sweet Corn. Mol. Plant Pathol. 2011, 12, 628-637. (2) Zhang, F.; Zou, M.; Chen, Y.; Li, J.; Wang, Y.; Qi, X.; Xue, Q., Lanthanide-Labeled Immunochromatographic Strips for the Rapid Detection of Pantoea Stewartii Subsp. Stewartii. Biosens Bioelectron. 2014, 51, 29-35. (3) Zhang, F.; Li, J.; Zou, M.; Chen, Y.; Wang, Y.; Qi, X., Simultaneous Detection of Clavibacter Michiganensis Subsp. Nebraskensis and Pantoea Stewartii Subsp. Stewartii based on Microsphere Immunoreaction. J. Biomol. Screening. 2013, 18, 474-480. (4) Thapa, S. P.; Park, D. H.; Wilson, C.; Hur, J. H.; Lim, C. K., Multiplex PCR Assay for the Detection of Pantoea Stewartii Subsp. Stewartii using Species-Specific Genetic Markers. Australas. Plant Pathol. 2012, 41, 559-564. (5) Wensing, A.; Zimmermann, S.; Geider, K., Identification of the Corn Pathogen Pantoea Stewartii by Mass Spectrometry of Whole-cell Extracts and Its Detection with Novel PCR Primers. Appl. Environ. Microbiol. 2010, 76, 6248-6256. (6) Chen, Y.; Zou, M.; Wang da, N.; Li, Y.; Xue, Q.; Xie, M.; Qi, C., An Immunosensor Based on Magnetic Relaxation Switch and Polystyrene Microparticle-induced Immune Multivalency Enrichment System for the Detection of Pantoea Stewartii Subsp. Stewartii. Biosens Bioelectron 2013, 43, 6-11. (7) Lin, D.; Wu, J.; Ju, H.; Yan, F., Signal Amplification for Electrochemical Immunosensing by In Situ Assembly of Host-guest Linked Gold Nanorod Superstructure on Immunocomplex. Biosens Bioelectron 2013, 45, 195-200. (8) Lin, D.; Wu, J.; Wang, M.; Yan, F.; Ju, H., Triple Signal Amplification of Graphene Film, 12

ACS Paragon Plus Environment

Page 12 of 26

Page 13 of 26

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

Polybead Carried Gold Nanoparticles as Tracing Tag and Silver Deposition for Ultrasensitive Electrochemical Immunosensing. Anal Chem 2012, 84, 3662-3668. (9) Yu, X.; Li, Y.; Wu, J.; Ju, H., Motor-based Autonomous Microsensor for Motion and Counting Immunoassay of Cancer Biomarker. Anal Chem 2014, 86, 4501-4507. (10) Guo, A.; Wu, D.; Ma, H.; Zhang, Y.; Li, H.; Du, B.; Wei, Q., An Ultrasensitive Enzyme-Free Electrochemical Immunosensor for CA125 using Au@Pd Core-Shell Nanoparticles as Labels and Platforms for Signal Amplification. J. Mater. Chem. B. 2013, 1, 4052-4058. (11) Martic, S.; Gabriel, M.; Turowec, J. P.; Litchfield, D. W.; Kraatz, H. B., Versatile Strategy for Biochemical, Electrochemical and Immunoarray Detection of Protein Phosphorylations. J Am Chem Soc 2012, 134, 17036-17045. (12) Yang, L.; Zhao, H.; Fan, S.; Deng, S.; Lv, Q.; Lin, J.; Li, C. P., Label-Free Electrochemical Immunosensor based on Gold-Silicon Carbide Nanocomposites for Sensitive Detection of Human Chorionic Gonadotrophin. Biosens Bioelectron 2014, 57, 199-206. (13) Zhang, J.; Lei, J.; Xu, C., Ding, L.; Ju, H., Carbon Nanohorn Sensitized Electrochemical Immunosensor for Rapid Detection of Microcystin-LR. Anal Chem, 2010, 82, 1117-1122. (14) Ambrosi, A.; Airo, F.; Merkoci, A., Enhanced Gold Nanoparticle based ELISA for a Breast Cancer Biomarker Anal Chem, 2010, 82, 1151-1156. (15) Zhao, J.; Zhang, Y.; Li, H.; Wen, Y.; Fan, X.; Lin, F.; Tan, L.; Yao, S., Ultrasensitive Electrochemical Aptasensor for Thrombin based on the Amplification of Aptamer-AuNPs-HRP Conjugates. Biosens Bioelectron 2011, 26, 2297-2303. (16) Zong, C.; Wu, J.; Wang, C.; Ju, H.; Yan, F., Chemiluminescence Imaging Immunoassay of Multiple Tumor Markers for Cancer Screening. Anal Chem 2012, 84, 2410-2415. 13

ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 14 of 26

(17) Wang, L.; Lei, J.; Ma, R.; Ju, H., Host-guest Interaction of Adamantine with a Beta-Cyclodextrin-Functionalized AuPd Bimetallic Nanoprobe for Ultrasensitive Electrochemical Immunoassay of Small Molecules. Anal Chem 2013, 85, 6505-6510. (18) Wan, Y.; Wang, Y.; Wu, J.; Zhang, D., Graphene Oxide Sheet-Mediated Silver Enhancement for Application to Electrochemical Biosensors. Anal Chem 2011, 83, 648-653. (19) Chen, L.; Zhang, X.; Zhou, G.; Xiang, X.; Ji, X.; Zheng, Z.; He, Z.; Wang, H., Simultaneous Determination of Human Enterovirus 71 and Coxsackievirus B3 by Dual-Color Quantum Dots and Homogeneous Immunoassay. Anal Chem 2012, 84, 3200-3207. (20) Jie,

G.;

Yuan,

J.,

Novel

magnetic

Fe3O4@CdSe

Composite

Quantum

Dot-based

Electrochemiluminescence Detection of Thrombin by a Multiple DNA Cycle Amplification Strategy. Anal Chem 2012, 84, 2811-2817. (21) Wang, L.; Chen, W.; Xu, D.; Shim, B. S.; Zhu, Y.; Sun, F.; Liu, L.; Peng, C.; Jin, Z.; Xu, C.; Kotov, N. A.; Simple, Rapid, Sensitive, and Versatile SWNT-Paper Sensor for Environmental Toxin Detection Competitive with ELISA. Nano Lett. 2009, 9, 4147-4152. (22) Pondman, K. M.; Maijenburg, A. W.; Celikkol, F. B.; Pathan, A. A.; Kishore, U.; Haken, B. t.; ten Elshof, J. E., Au Coated Ni Nanowires with Tuneable Dimensions for Biomedical Applications. J. Mater. Chem. B. 2013, 1, 6129-6136. (23) Wang, Y.; Zhang, Y.; Su, Y.; Li, F.; Ma, H.; Li, H.; Du, B.; Wei, Q., Ultrasensitive Non-Mediator Electrochemical

Immunosensors

using

Au/Ag/Au

Core/double

Shell

Nanoparticles

as

Enzyme-Mimetic Labels. Talanta 2014, 124, 60-66. (24) Kuang, H.; Chen, W.; Xu, D.; Xu, L.; Zhu, Y.; Liu, L.; Chu, H.; Peng, C.; Xu, C.; Zhu, S., Fabricated Aptamer-based Electrochemical "signal-off" Sensor of Ochratoxin A. Biosens Bioelectron 14

ACS Paragon Plus Environment

Page 15 of 26

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

2010, 26, 710-716. (25) Zhang, Q.; Chen, X.; Tu, F.; Yao, C., Ultrasensitive Enzyme-Free Electrochemical Immunoassay for Free Thyroxine based on Three Dimensionally Ordered Macroporous Chitosan-Au Nanoparticles Hybrid Film. Biosens Bioelectron 2014, 59, 377-383. (26) Kavosi, B.; Hallaj, R.; Teymourian, H.; Salimi, A., Au Nanoparticles/PAMAM Dendrimer Functionalized Wired Ethyleneamine-Viologen as Highly Efficient Interface for Ultra-Sensitive Alpha-Fetoprotein Electrochemical Immunosensor. Biosens Bioelectron 2014, 59, 389-396. (27) Wang, L.; Jia, X.; Zhou, Y.; Xie, Q.; Yao, S., Sandwich-Type Amperometric Immunosensor for Human Immunoglobulin G using Antibody-Adsorbed Au/SiO2 Nanoparticles. Microchim. Acta 2010, 168, 245-251. (28) Yan, M.; Zang, D. J.; Ge, S. G.; Ge, L.; Yu, J. H., A Disposable Electrochemical Immunosensor based on Carbon Screen-Printed Electrodes for the Detection of Prostate Specific Antigen. Biosens Bioelectron 2012, 38, 355-361. (29) Lv, X.; Ge, W.; Li, Q.; Wu, Y.; Jiang, H.; Wang, X., Rapid and Ultrasensitive Electrochemical Eetection of Multidrug-Resistant Bacteria based on Nanostructured Gold Coated ITO Electrode. ACS Appl. Mater. Interfaces 2014, 6, 11025-11031. (30) Zhao, Y.; Xu, L.; Ma, W.; Wang, L.; Kuang, H.; Xu, C.; Kotov, N. A.; Shell-Engineered Chiroplasmonic Assemblies of Nanoparticles for Zeptomolar DNA Detection. Nano Lett. 2014, 14, 3908-3913. (31) Zhao, Y.; Xu, L.; Liz-Marzán, L. M.; Kuang, H.; Ma, W.; Asenjo-Garcı́a, A.; García de Abajo, F. J.; Kotov, N. A.; Wang, L.; Xu, C., Alternating Plasmonic Nanoparticle Heterochains Made by Polymerase Chain Reaction and Their Optical Properties. J. Phys. Chem. Lett. 2013, 4, 641-647. 15

ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

(32) Zhao, Y.; Xu, L.; Kuang, H.; Wang, L.; Xu, C., Asymmetric and Symmetric PCR of Gold Nanoparticles: A Pathway to Scaled-Up Self-Assembly with Tunable Chirality. J. Mater. Chem. 2012, 22, 5574-5580. (33) Lei, J.; Ju, H., Signal Amplification using Functional Nanomaterials for Biosensing. Chem Soc Rev 2012, 41, 2122-2134. (34) Fernandes, A. M.; Abdalhai, M. H.; Ji, J.; Xi, B. W.; Xie, J.; Sun, J.; Noeline, R.; Lee, B. H.; Sun, X., Development of Highly Sensitive Electrochemical Genosensor based on Multiwalled Carbon Nanotubes-Chitosan-Bismuth and Lead Sulfide Nanoparticles for the Detection of Pathogenic Aeromonas. Biosens Bioelectron 2015, 63, 399-406. (35) Huang, C. F.; Yao, G. H.; Liang, R. P.; Qiu, J. D., Graphene Oxide and Dextran Capped Gold Nanoparticles based Surface Plasmon Resonance Sensor for Sensitive Detection of Concanavalin A. Biosens Bioelectron 2013, 50, 305-310.

16

ACS Paragon Plus Environment

Page 16 of 26

Page 17 of 26

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

Captions: Scheme 1. Schematic illustration of Au NPs amplified electrochemical immunoassay for PSS detection. Figure 1. (a) TEM images of 18 ± 2 nm Au NPs; (b) UV-vis spectra of D-Ab, D-Ab-HRP, Au NPs and the conjugates of D-Ab-HRP-Au NPs. Figure 2. The current response of immunosensor in pH 7.0 PBS solution (a) at different HQ concentration under 1 mM H2O2, 1 µg/mL D-Ab-HRP-Au and incubation for 45 min; (b) at different H2O2 concentration under 1.5 mM HQ, 1 µg/mL D-Ab-HRP-Au NPs and incubation for 45 min; (c) at different D-Ab-HRP-Au NPs concentration under 1.5 mM HQ, 2 mM H2O2 and incubation for 45 min; (d) at different incubation time under 1.5 mM HQ, 2 mM H2O2 and 1 µg/mL D-Ab-HRP-Au NPs. Figure 3. CV curves of (a) bare GCE in pH 7.0 PBS solution and (b-d) PSS-C-Ab-GCE in pH 7.0 PBS solution containing 1.5 mM HQ and 2 mM H2O2, without D-Ab-HRP (b), with D-Ab-HRP (c), with D-Ab-HRP-Au NPs (d). Figure 4. LSV curves of immunosensor at different PSS concentration. Figure 5. The calibration plots of the peak current of LSV and PSS concentration ranging from 2.0×107 cfu/mL to 4.0×104 cfu/mL. Figure 6. Evaluation of the cross-reactivity of electrochemical immunosensor at different target analytes. (a) PSS, (b) Burkholderia glumae, (c) Rice bacterial leaf streak pathogen, (d) Rice bacterial cercospora leaf spot pathogen, (e) Crucifer black spot pathogen. Table 1. Spiked experiments for different concentration of PSS.

17

ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Scheme 1. Schematic illustration of Au NPs amplified electrochemical immunoassay for PSS detection.

18

ACS Paragon Plus Environment

Page 18 of 26

Page 19 of 26

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

Figure 1. (a) TEM images of 18 ± 2 nm Au NPs; (b) UV-vis spectra of D-Ab, D-Ab-HRP, Au NPs and the conjugates of D-Ab-HRP-Au NPs.

19

ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 2. The current response of immunosensor in pH 7.0 PBS solution (a) at different HQ concentration under 1 mM H2O2, 1 µg/mL D-Ab-HRP-Au and incubation for 45 min; (b) at different H2O2 concentration under 1.5 mM HQ, 1 µg/mL D-Ab-HRP-Au NPs and incubation for 45 min; (c) at different D-Ab-HRP-Au NPs concentration under 1.5 mM HQ, 2 mM H2O2 and incubation for 45 min; (d) at different incubation time under 1.5 mM HQ, 2 mM H2O2 and 1 µg/mL D-Ab-HRP-Au NPs.

20

ACS Paragon Plus Environment

Page 20 of 26

Page 21 of 26

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

Figure 3. CV curves of (a) bare GCE in pH 7.0 PBS solution and (b-d) PSS-C-Ab-GCE in pH 7.0 PBS solution containing 1.5 mM HQ and 2 mM H2O2, without D-Ab-HRP (b), with D-Ab-HRP (c), with D-Ab-HRP-Au NPs (d).

21

ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 4. LSV curves of immunosensor at different PSS concentration.

22

ACS Paragon Plus Environment

Page 22 of 26

Page 23 of 26

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

Figure 5. The calibration plots of the peak current of LSV and PSS concentration ranging from 2.0×107 cfu/mL to 4.0×104 cfu/mL.

23

ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 6. Evaluation of the cross-reactivity of electrochemical immunosensor at different target analytes. (a) PSS, (b) Burkholderia glumae, (c) Rice bacterial leaf streak pathogen, (d) Rice bacterial cercospora leaf spot pathogen, (e) Crucifer black spot pathogen.

24

ACS Paragon Plus Environment

Page 24 of 26

Page 25 of 26

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

Table 1. Spiked experiments for different concentration of PSS. Spiked concentration (cfu/mL)

Detected concentration (cfu/mL)

Recovery (%)

1.0 × 107

9.2 × 106

92.5 ± 2.4

6

6

2.0 × 10

1.8 × 10

90.6 ± 1.7

4.0 × 105

4.3 × 105

107.5 ± 3.4

4

4

106.3 ± 2.6

8.0 × 10

8.5 × 10

25

ACS Paragon Plus Environment

ACS Applied Materials & Interfaces

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

TOC Figure

26

ACS Paragon Plus Environment

Page 26 of 26