Fly ash characterization from Cynara cardunculus L. gasification

Subscriber access provided by UNIV OF DURHAM

Biofuels and Biomass

Fly ash characterization from Cynara cardunculus L. gasification Daniel Serrano Garcia, Marzena Kwapinska, Sergio Sanchez Delgado, and James J. Leahy Energy Fuels, Just Accepted Manuscript • DOI: 10.1021/acs.energyfuels.7b04050 • Publication Date (Web): 19 Apr 2018 Downloaded from http://pubs.acs.org on April 19, 2018

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

Fly ash characterization from Cynara cardunculus L. gasification AUTHOR NAMES Daniel Serranoa*, Marzena Kwapinskab**, Sergio Sánchez-Delgadoa, James J. Leahyc AUTHOR ADDRESS a

Energy System Engineering Research Group, Thermal and Fluid Engineering Department, Carlos III University of Madrid, Leganés, Madrid, Spain b

c

Dairy Processing Technology Centre, University of Limerick, Limerick, Ireland

Carbolea Research Group, Department of Chemical Sciences, Bernal Institute, University of Limerick , Limerick, Ireland

ABSTRACT

This study analyzes the characteristics of fines produced during the air-blown gasification of Cynara cardunculus L. in a bubbling fluidized bed. These fines are collected by means of two hot cyclones and a hot filter. The gasification temperature is varied from 700 to 800 ºC using olivine and magnesite as bed materials, with an equivalence ratio (ER) of 0.2. Relatively high carbon content is found in the entrained fines for all experiments. The lower heating value (LHV) of the elutriated fines varies from 5.2 to 9.4 MJ/kgdb. Around 75 % of the fines are

ACS Paragon Plus Environment

1

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 2 of 35

captured in the first cyclone, 5 % in the second cyclone and the remaining 20 % in the hot filter. The concentration of elements such as Se and Cl makes these fly ashes a hazardous material. Based on these properties the potential reuse of fly ashes is evaluated.

GRAPHICAL ABSTRACT

1. INTRODUCTION Gasification is a promising technology to transform biomass into a useful product gas. However, this process generates an ash residue that needs to be disposed of or reused in a different application. This aspect is often overlooked in biomass gasification studies which usually concentrate their attention on gas yields and tar mitigation. The elements that form the inorganic fraction of the biomass are divided into major elements, minor elements and trace elements mainly formed by heavy metals 1. However, this composition depends on the origin and handling of the biomass 2. The composition of the biomass ash plays a major role in the treatment of this residue as different regulations exist depending on the country or region for its use in terms of the content of some toxic elements such as Cd, Hg, Ni, Pb, Se or Zn that can increase the contamination of air, water and soils, or can threaten human health

1,3

.


2

Page 3 of 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

The final composition of fly ash depends also on the atmosphere, reducing or oxidative, at which the conversion process is carried out 3. Dong et al. 4 found that a reducing atmosphere promotes the evaporation of Cd and Zn while Pb, Cu, Ni, and Cr volatilization is enhanced under an oxidative atmosphere. In addition, presence of chlorine promotes the evaporation of heavy metals in form of metal chlorides that tend to condense on fine particles, leading into the corrosion of the different parts of the installation

5–8

. Belevi and Moench 9, on the other hand,

found that during the incineration of (household waste) the content of Al, Ba, Ca, Co, Cr, Fe, K, Li, Mg, Mn, Na, Ni, P, Si and Ti in fly ash is not much influenced by chemical conditions (temperature or redox conditions) whereas Cu and Zn are favored by oxidative conditions. In the case of biomass combustion, there is an extensive library of literature which deals with ash characterization and utilization gasification fly ash is very limited

15–17

10–14

. However, the information regarding biomass

and its composition is also quite different from that of

combustion plants, containing high amounts of unburned carbon, polycyclic aromatic hydrocarbons (PAHs), chlorine and heavy metals. All these features make the use of gasification fly ashes more complicated and suggest that coal combustion fly ash utilization options are not suitable for biomass gasification ash, giving rise to the requirement for some pretreatment

18,19

.

Different studies have been performed within the GASASH project 15, trying to find sustainable and economic methods for gasification ash management. When the carbon content is high, combustion is the most promising method to reduce the un-reacted carbon and the amount of undesirable compounds such as the PAHs, chlorine and some heavy metals as well as recovering energy. This reduces the volume of the fly ashes and applications such as construction products can be considered for the new ash generated 15.


3

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 4 of 35

The use of biomass gasification fly ashes in construction have been investigated by many authors: concrete paving blocks 20, fire-resistant boards 18, lightweight bricks 19 or clay bricks 21. These preliminary studies conclude that fly ashes have high potential as a binding material within different construction components. The properties of biomass gasification fly ash collected in different locations of the cleaning section was investigated by Liao et al. 22. They observed that the most volatile compounds (CaO, Na2O, MgO, Cl, P2O5, SrO, As5O3, ZnO and Al2O3) were mostly found in the ash scrubber while the less volatile species (NiO, Cr2O3, PbO, CuO and MnO) stayed in the cyclone. Narayan et al. 23

found that cyclone ash was dominated by K and Ca silicates. They also found high fractions of

K and Ca in the second cyclone. C. cardunculus L. is a perennial energy crop native to Mediterranean regions (Spain, Portugal or Greece), and is commonly known as cardoon or thistle. However, it also grows as weed in other parts of the world like Argentina or California 24. Cardoon is suitable for cultivation in the dry soils of the Mediterranean region and has some distinct advantages over other biomass plants: low water irrigation requirement, enhancement of soil characteristics, low cost, and the possibility to grow in lands that are not suitable for food purposes

25,26

. The cultivation of C.

cardunculus L. has been studied by different authors due to its importance for biomass production

25–29

. They show a cardoon production of between 1.4 and 25 tdb/ha·year, depending

on the irrigation and annual rainfall with annual costs of around 65 €/t, including establishment and operating costs. Further information can be found in a recently published review which considers the research carried out with this feedstock in the last 30 years

30

.

Different

gasification studies have been performed using C. cardunculus L. as a feedstock 31–37. However,


4

Page 5 of 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

to the authors’ knowledge, the properties of the entrained fines from gasification of cardoon have never been investigated. Therefore, the objective of this work is to analyze the entrained fines collected from cardoon air gasification in a BFB pilot plant and focus the attention on this residue which has been not always considered as has been recently reported by Thomsen et al. 17. For this purpose, a multilayer characterization: CHN-S, loss on ignition (LOI), moisture, ash, lower heating value (LHV), chlorine and metal composition, has been carried out on the samples as well as a mass balance of the 18 elements retained in the solid by-products of gasification. Based on these characteristics, the different possible applications employed for combustion fly ashes are evaluated for cardoon gasification fly ashes in order to determine if they meet the specific requirements for each application and to check toxicity of these fines in case they have to be landfilled. 2. EXPERIMENTAL SETUP 2.1. Biomass and bed material. Cardoon pellets are used as the feedstock. Cardoon is characterized by relatively high ash content when compared to other biomass crops such as Miscanthus or Reed Canary Grass (Phyllis database, https://www.ecn.nl/phyllis2/). Typical ash content reported for cardoon are 11.3 %

38

, 15.4 %

34

and 7.2 %

25

. The high volatile matter

content and higher heating value (HHV) make cardoon a good option for gasification. However, the high sodium and potassium content in the ash exposes cardoon to a high risk of bed agglomeration 39. In order to avoid this undesirable problem 3 wt.% of kaolin (Al2Si2O5(OH)4) is added to the cardoon prior to gasification as suggested by Llorente et al.

40

and Weber and

Quicker 41. Table 1 shows the chemical characteristics of the fuel mixed with addition of 3 wt. % of kaolin, as it is used in the experiments. Table 1. Biomass properties (cardoon ar. with 3 wt.% of added kaolin).


5

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Proximate analysis [wt.% ar] Moisture Volatile Matter Fixed Carbon Ash

Page 6 of 35

Ultimate analysis [wt.% db] 9.69 69.83 10.21 10.27

Higher heating value [MJ/kg db] 17.50 Ash composition[g/kg ash db] Al 110.76 Ca 151.06 Cu 5.14 Fe 9.37 K 86.61 Minor elements [mg/kg ash db] Cd 201.41 Co 221.51 Cr 100.70 Mn 508.56 ar: as received, db: dry basis, a by difference

Carbon Hydrogen Nitrogen Sulphur Chlorine Oxygena

48.91 5.90 0.58 0.09 0.91 32.24

Mg Na Se Si

18.13 247.73 5.54 312.19

Mo Ni Pb Zn

805.64 413.90 10.07 312.19

Olivine, supplied by Magnolithe, Austria, and magnesite, obtained from MINELCO, U.K., are employed as bed materials (Table 2). Both olivine and magnesite are commonly used as bed materials in biomass gasification showing good operational performance in terms of agglomeration and improvements in gas composition and tar mitigation 42,43. Table 2. Bed materials composition.

MgO [wt.%] SiO2 [wt.%] Fe2O3 [wt.%] CaO [wt.%]

Olivine 2.69 88.33 6.59 –

Al2O3 + Cr2O3 + Mn3O4 [wt.%]

2.69

Magnesite 74.05 21.10 0.63 0.84 3.35

2.2. Experimental facility. A pilot scale air-blown bubbling fluidized bed gasifier is used for the experimental campaign. This facility is located at the University of Limerick. The fluidized bed consists of a lower section of 134.5 mm internal diameter and a freeboard of 211.6 mm internal diameter, with a total height of 3000 mm. The entire facility including reactor and


6

Page 7 of 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

downstream cleaning section are heated, insulated and monitored with temperature and pressure sensors. Further information about this setup can be found elsewhere 37,44. 2.3. Experimental procedure. The reactor is loaded with olivine or magnesite to a bed height of 26.90 cm. The air flow rate is kept at a constant value of 63 Ndm3/min for all the experiments and the electrical furnaces are set to the experimental temperature for each test i.e. 700, 760 or 800 º C. When the bed temperature reaches the maximum allowable temperature using the electrical furnaces, biomass feeding commences leading to a further increase of the temperature up to the desired temperature due to the partial combustion of the biomass. After approximately 40 min after the introduction of the biomass a stable temperature operation is achieved. The selected air and biomass rates result in a constant ER, defined as the ratio between the air flow rate introduced into the reactor and the stoichiometric air flow rate needed for the complete combustion of the biomass, of 0.20. This value has been chosen according to an approximate u/umf ratio of 3, a typical value for BFB gasifiers, and a biomass feeding rate of 4.5 kg/h which was easily maintained by the feeding system. The feeding system is pressurized with a nitrogen flow of 2 Ndm3/min to prevent the backflow of gases from the gasifier. The gas leaves the reactor passing through two hot cyclones and a hot filter (Candle element, Pyrotex BWF-Envirotec) to obtain high ash retention rates whose temperatures are kept at 400 and 450 ºC, respectively, to prevent tar from condensing. Entrained particles, such as fine bed particles, char and fly ash are stored in these devices. The principal operating conditions can be found in Table 3. Table 3. Main operating conditions and gasification results. Operating conditions Bed material Biomass feeding rate [kgdaf/h]

Olivine, 5.38 kg 3.55

Magnesite, 5.70 kg 3.56


7

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Air flow rate [Ndm3/min] ER [─] Experiment duration [min] Inlet air temperature [ºC] Gasification temperature [ºC] Freeboard temperature [ºC] Cyclones temperature [ºC] Hot filter temperature [ºC]

63.07 0.20 1.5 – 1.7 227 – 320 700 – 800 500 400 450

Page 8 of 35

63.47 0.20 2.3 270 800 500 400 450

When the experiments are completed the facility is cooled to ambient temperature using an N2 purge. Fly ash and entrained particles from cyclones and filter are discharged, weighed and retained for analysis. 2.4. Methods of fines analysis. All samples from the two cyclones and the hot filter are analyzed using a CHN-S elemental analyzer, a drying oven and an ash furnace in order to get the ultimate analysis, and moisture and ash contents. The HHV is also measured using an isoperibolic calorimeter, and the LHV is calculated using the moisture and hydrogen content of the sample, M and H, respectively, and the latent heat of steam, hg, (Eq. 1)

45

. Ash (at 550 ºC

according to CEN/TS 14775:2004) is obtained from the samples and digested following the procedure described by Serrano et al.

37

. Bed materials are also digested according to the same

procedure. The inorganic elemental composition is determined using an atomic absorption spectrometer (AAS) or inductive coupled plasma atomic spectroscopy (ICP-OES) for Hg, As, Sb and S. The LOI of the fly ash is determined as the weight loss between the dry samples and the weight of the samples after being kept at 550 ºC for 90 minutes. = − ℎ

+

(1)

In order to test the metal mobility, 5 g of dry fines are mixed with deionised water, in a liquid to solid ratio (L/S) of 10. The mixture is continuously agitated for 24 h and then filtered as


8

Page 9 of 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

indicated in the DIN 38414-S4 standard for leaching tests. Finally, the liquid samples/leachates are analyzed by AAS. 3. RESULTS AND DISCUSSION In this section, the characteristics of the ashes collected in the two cyclones and the hot filter are presented and analyzed. An extensive discussion of the gasification results, gas composition, tar analysis and catalytic effect of bed materials, can be found in a previous publication 37. Different amounts of fines are collected by the three cleaning devices: around 75 wt.% of the total in the first cyclone, 5 wt.% in the second cyclone and 20 wt.% in the hot filter. Table 4 shows the amount of fines accumulated in the different devices, over the lifetime of each experiment. 3.1. Ash characterization 3.1.1. Elemental composition, ash and moisture. The fines escaping the reactor are mainly composed of ash, more than 69 wt.% db, and to a lesser extent by carbon (Table 4). The carbon content of the samples is moderately high (13 – 25 wt.% db). The negative values for the oxygen content in the magnesite experiments are due to the differences in the final mass of the inorganic residue (ash) left after the elemental analysis (1200 ºC) and ash content determined at 550 ºC. The amount of oxygen in a dry sample is calculated by difference between the sum of C, N, H, S, Cl, ash, and the mass of sample before the analysis. If in the analyzed sample some carbonates are present they are volatilized during analysis decreasing the final mass of the residual ash left. For calculations, the ash content determined according to relevant standard at 550ºC is routinely used, which gives slightly higher values therefore when the oxygen content in a sample is very low it may lead to negative values.


9

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 10 of 35

Table 4. Elemental composition, moisture and ash content, and LHV of the fines from the cyclones and hot filter. mfines

C

H

N

S

Cl

Oa

Moisture

Ash

LHV

[g/h]

[wt.% db]

[wt.% db]

[wt.% db]

[wt.% db]

[wt.% db]

[wt.% db]

[wt.% ar]

[wt.% db]

[MJ/kg db]

0.58

0.09

0.91

32.24

9.69

11.37

15.81

0.25 0.24 0.17

0.07 0.04 0.07

2.32 2.03 3.33

2.13 2.10 0.44

1.38 1.55 0.22

69.94 78.70 75.93

9.54 6.44 6.67

0.37 0.27 0.22

0.07 0.04 0.05

2.85 2.63 3.60

1.55 2.46 0.67

0.75 2.28 0.00

69.71 76.55 73.65

9.02 6.45 7.94

0.31 0.24 0.35

0.14 0.09 0.08

3.75 3.33 3.70

7.00 3.64 5.00

1.59 2.08 1.02

70.09 79.12 76.55

7.15 5.28 5.24

0.21 0.21 0.19

0.09 0.10 -

2.90 2.93 -

-3.38 -3.47 -

1.38 2.23 0.66

74.14 77.09 75.40

8.53 7.35 7.50

Cardoon + kaolin 48.91 5.90 Olivine 700 ºC Cyclone 1 162.8 24.67 0.62 Cyclone 2 11.7 16.53 0.36 Filter 44.1 19.66 0.40 Olivine 760 ºC Cyclone 1 164.7 24.85 0.60 Cyclone 2 12.4 17.73 0.32 Filter 48.8 21.36 0.45 Olivine 800 ºC Cyclone 1 175.8 18.41 0.30 Cyclone 2 18.0 13.41 0.17 Filter 27.0 14.19 0.13 Magnesite 800 ºC Cyclone 1 217.2 25.79 0.25 Cyclone 2 17.5 23.05 0.09 Filter 62.2 24.49 0.15 ar: as received, db: dry basis, a by difference

The carbon content is higher for fines collected in the first cyclone than in the second one and the filter. Furthermore, the carbon content in the second cyclone always shows the lowest value. On the other hand, the highest amount of ash is obtained in the second cyclone while the lowest ash concentration is found in the first cyclone. It should be noted that the mean carbon content in the two cyclones and the hot filter decreases with temperature. Olivine and magnesite show some differences in terms of carbon content at the same temperature, with the value being higher for magnesite. The LOI of the cardoon fly ashes ranges from 19 to 33 wt.% db (Figure 1a), which are very similar to those obtained in full-scale gasifiers. These results are in agreement with the higher carbon conversion when the temperature is increased and when olivine is used instead of magnesite at the same temperature 37 and with the values reported in other works 16.


10

Page 11 of 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

3.1.2. Chlorine and sulphur content. Sulphur and chlorine contents are shown in Table 4. Sulphur content is similar in all samples, on average around 0.08 wt.% (dry basis). In the case of the chlorine concentrations, values of between 2 and 4 wt.% are observed. The content of Cl is higher in fly ash collected in hot filter since more Cl containing compounds condense on finer particles, which have greater surface area. The contents of S and Cl are in the range of other fines collected from different biomasses and gasifiers reported in the literature 15. 3.1.3. Energy content. The LHV of the samples collected in the first cyclone is from 13 to 33 % higher than the fines collected in the filter and in the second cyclone (Table 4). The mean values for each experiment are between 5 and 10 MJ/kgdb, and are lower than the values obtained from full-scale gasifiers which are in the range of 14-25 MJ/kg

15

. However, these values are,

more or less, half of the LHV of the original biomass. Therefore, a considerable amount of energy per unit of mass, 2-3 % of the energy introduced with the biomass, remains in the fines. This amount of energy can be important in industrial scale plants, and can be recovered for other applications. There are negligible differences between the mean LHV at 700 and 760 ºC in the case of olivine. However, the differences increase when the temperature is raised to 800 ºC, with a considerable decrease of the LHV. There is also a significant difference in the LHV between the bed materials at this temperature. When magnesite is used, the LHV of the fines is higher than for olivine at the same temperature. These trends resemble carbon content since calorific value refers to carbon content in fines. 3.1.4. Distribution of elements/metals in the solid streams from gasification. The main ash forming inorganic elements found in fines are Al, Ca, K, Mg, Na, Si, and, to a lesser extent, Fe (Figure 1a). Si is the most abundant element which is in accordance with the amount of Si in the


11

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 12 of 35

cardoon and kaolin mixture. Jordan and Akay 46 reported a similar composition for the main ash forming elements in bagasse gasification ash. Gasification temperature affects the distribution of Ca, K and Mg whose concentration increases with temperature at all sampling points. Concentration of Na and Fe remain more or less constant in all gas treatment devices as well as Al in cyclone 2 and the hot filter. Concentration of Si does not change with temperature in the samples collected at cyclone 1, but greater fluctuation is observed for the samples from cyclone 2 and the hot filter where the differences are very marked. Considering both bed materials, the Mg content is clearly higher for magnesite because of possible entrainment of the bed particles (Table 2) and/or enrichment of cyclone fines in magnesium due to abrasion. The concentrations of some major elements such as Al, Na, K and Si are higher in C. cardunculus fines than reported in other experiments 15. Mg is similar to other biomasses while Ca and Fe concentrations are rather smaller. These differences are influenced by the ash composition of the original biomass and kaolin addition. Furthermore, the bed material employed also has an influence as some elements become detached from the bed material surface due to abrasion or catalytic action with, and contribute to enrichment in the fines.


12

Page 13 of 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

Figure 1. a) Main inorganic elements found in the collected fines at the different locations, and b) minor elements concentration in collected fines for different temperatures, bed materials, and sampling locations: (red) olivine 700 ºC, (blue) olivine 760 ºC, (green) olivine 800 ºC, (orange) magnesite 800 ºC. The concentration of minor elements (Figure 1b) shows little variation with temperature, sampling location and bed material with exception of Cr, Mo and Ni for which show significant differences. Higher content of Cr, Mo and Ni are observed for gasification tests at higher temperature. No As and Sb were observed in the samples analyzed. An attempt is made to perform mass balances for the 18 elements collected in the solid streams, where biomass with kaolin is the input stream and the entrained fines and the bed char are the outputs (Figure 2). Metal recovery, defined as the ratio between the mass flow of an element collected in the char and in the cleaning system with that of and the inlet mass flow of that element in the biomass was calculated for all elements. The recovery for K, Ca, and to a lesser extent, Mg is slightly influenced by process temperature due to their lower boiling points


13

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 14 of 35

compared to metals like Al, Fe and Si (Figure 2a). For magnesite test and in a lesser extent for olivine tests, Mg enrichment in the fines is observed caused by abrasion of magnesite particles during the operation of the fluidized bed or entrainment of small bed material particles. The chlorine recovery is rather low, with only 15-22 % captured on fly ash particles, indicating this element is volatilized and released in the gas phase as HCl, KCl and NaCl

47

. Some of this

chlorine is captured by other elements that condense in the downstream devices. Chlorine under reducing/pyrolysis conditions is released mostly as CH3Cl at 350 ºC with minor amounts of HCl 48

. At temperatures above 700 ºC, gaseous Cl is recaptured by either K salts (KCl, (KCl)2) or K

in the char matrix 49–51. Gaseous KCl condenses and forms aerosols. In the case of bed char, higher mass retention of all the different elements is observed at lower gasification temperatures. This shows an effect of temperature on the release of inorganics from biomass, regardless of whether olivine or magnesite is used. The fate of the different metals cannot be accurately determined because it was impossible to separate and analyze the bottom ash from bed material and char particles while the metal emissions in the product gas were not measured. The high content of Fe and Si (especially for experiment with olivine at 700 and 760°C) in char composition, coming from bed materials, are an indication of this fact. It is worth noting the high recovery values for Cr, Mn, Mo and Ni in the fines (Figure 2b, raster filled bars) which is probably due to the abrasion of bed materials particles, in particular Cr and Ni from olivine

52

and the decomposition of the reactor walls releasing lubricants and

residuals from previous tests

53,54

. The high recovery values for Pb are related to the inherently

high volatility of this element combined with the reducing atmosphere that enhances its volatility 4

. At a temperature of 850 ºC, Pb is completely vaporized as PbCl4 and PbCl2

55

and capture by

Al and Si oxides when the temperature decreases 56. The Cu was mainly retained/captured in the


14

Page 15 of 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

fines. The distribution of heavy metals is shifted towards the entrained fines, with their mass in the char being much lower than in the fines.

Figure 2. Mass balance for fines composition: a) major elements and b) minor elements. Taking into account the fuel input, the char and the entrained fines, the closure of the mass balance was less than 100 % for all major elements except for the elements mentioned above. The excess in Mg and Si mainly comes from the char composition as it is observed in Figure 2a, where some bed particles could be retained in the char pores. In the case of Cr, the surplus could be produced from attrition of bed particles with the reactor walls in which trace particles are mainly retained in the first cyclone. The overall mass balance is not complete due to the lack of information from the ash inside the gasifier as it is difficult to and the elements which are volatilized and deposited on downstream colder surfaces. However, these values are within the limits reported in the literature 54,57,58. The corresponding enrichment factors (EF)

59

(Eq. 2), for all elements are calculated and

presented in Table 5.


15

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

=

·

% "

Page 16 of 35

(2)

Meij 59 classified the distribution of elements in different ash types from coal fired power plant into three main groups. They referred fly ash metals like Al, Ca, Ce, Fe, K, Mg, Si and Ti as group I (EF~1); these elements do not volatilize during gasification and distribute equally between bed material and fly ashes. Group II elements (EF~1.3-4): As, Ba, Be, Cd, Cr, Mn, Na, Co, Cu, Ni, P, Pb, Tl, V and Zn, which are vaporized at high temperature and condense on the surface of fly ash particles. Very volatile elements like B, Br, Hg, Cl, F, N and Se with a limited capacity of condensing on the surface of submicron particles of ash, which are partly emitted in the vapor phase are referred to as group III. In this group EF

Fly ash characterization from Cynara cardunculus L. gasification

Recommend Documents