Layered double hydroxides as supported anionic reagents. Halide-ion

Oxidation of Cr(III) to Cr(VI) Species During the Thermal Decomposition Process of Zn/Cr-layered Double Hydroxide Carbonate. Kiyoshi Fuda , Kazuhito S...
0 downloads 0 Views 300KB Size
J . Am. Chem. SOC.1986, 108, 541-542

54 1

detailed reaction mechanisms are not clear. The CC&-potassium superoxide reaction should yield an active intermediate, the C13CO0. radical, which oxidizes electron-rich olefins to afford the corresponding epoxides and which is a markedly more potent oxidizing agent than superoxide alone.

Layered Double Hydroxides as Supported Anionic Reagents. Halide Ion Reactivity in [Zn2Cr(OH)6]X.nH20 Kevin J. Martin and Thomas J. Pinnavaia*

0.20-

Michigan State University, Department of Chem try East Lansing, Michigan 48824 Received November 14, 1985 Several new families of heterogeneous catalysts recently have been synthesized by intercalating metal ions and cationic metal complexes between the negatively charged layers of smectite clay A complementary class of layered compounds exist in which the charge on the layers and gallery ions is the reverse of that found for smectite clays. These are the layered double hydroxides (LDH's) of the type [M,"M,"'(OH)2(++V)]A,,,. Z H ~ O The . ~ positively ~ charged layers are brucitelike (MI(OH)~) TIME, sec with trivalent cations substituting for divalent cations in octahedral Figure 1. Pseudo-first-order kinetic plots for the reaction of (A) n-butyl sites of the hydroxide sheet. Typically, the ratio y / x is in the range bromide and (B) 3-methylbutyl bromide with Zn2Cr(OH)61.2H20 in 0.20-0.50. In naturally occurring LDH minerals the interlayer toluene suspension at 90 "C. The L D H was predried at 150 OC under anion A"- is most commonly carbonate as in hydrotalcite, Mg6argon prior to reaction. The initial reaction mixtures contained 1.0 mmol A12(OH)16(C03).4H20,and pyroaurite, M&Fe2(0H)16(C03). of alkyl bromide and L D H in 3.0 mL of toluene. [RBr],/[RBr], is the 4H20. However, a wide range of derivatives containing various fraction of substrate unreacted at time t. combinations of MI', MI1', and A" ions can be synthesized either by direct crystallization@ from aqueous solution or by anion Table I. Pseudo-First-Order Rate Constants" (90 "C) for Halide exchangelo for A" in a precrystallized host. Exchange between Alkyl Bromides in Toluene and Zn2Cr(OH)J2H20 LDH's have been investigated as solid ionic conductors" and as catalyst p r e c ~ r s o r s , ' ~but J ~ the properties of the pristine comiO5koW,s-I m-2 pounds as supported anionic reagents or as catalysts for chemical L D H dried L D H dried synthesis have not been addressed. Unlike the galleries of alkyl bromide at 25 "C at 150 OC smectites, which can be swelled by multiple layers of solvent to n-C4H9Br 1.1 3.0 mimic a solution-like environment,' the galleries of LDH's acn-C5HIIBr 1.1 3.6 commodate only one or two layers of water and other polar i-CSH,IBr 0.60 1.6 molecules. This limitation in gallery swelling, along with the n-C6H,,Br 0.83 3.1 relatively high layer charge density, means that typical organic n-C8H1,Br 0.87 2.4 reagents are unable to penetrate the intracrystal space occupied 'Rate constants have been normalized per unit surface area of LDH. by the anions. Here we demonstrate that although the gallery anions in a typical LDH are not accessible for direct intracrysThe roduct was identified by X-ray diffraction analysis (dw3= talline reaction, they are readily transferred to external edge 7.7 Exchange of the chloride form with excess 1.0 M NaI surfaces for reaction with substrates adsorbed at those sites. solutions afforded the iodide form with dw3 = 8.3 A.lS N2 BET The reactions investigated were simple halide-exchange prosurface areas were 7.7 and 9.4 m2/g, respectively, for LDH cesses between the halide ions in Zn2Cr(OH)6X.H20and alkyl samples dried under Argon at 25 and 150 O C . halides in the condensed state (toluene) or in the vapor phase. The Condensed-phase reactions were carried out in culture tubes chloride form of the LDH was prepared by reaction of aqueous containing 3.0 mL of toluene and 1.0 mmol each of LDH and CrC13with ZnO according to previously described p r o c e d ~ r e s . ~ ~ J ~ alkyl halide. The reaction mixture was stirred vigorously while being maintained at 90 O C in an oil bath, and samples were withdrawn periodically for analysis by gas chromatography. (1) Pinnavaia, T. J. Science (Wmhingron, D.C.) 1983, 220, 365. Reactions of alkyl halides in the vapor phase with LDH were (2) Thomas, J. M. 'Intercalation Chemistry": Whittingham, M. S.,Jacarried out in a microreactor in the temperature range 90-1 50 cobson, A. J., Eds.; Academic Press: New York, 1982: Chapter 3. "C. The reactor was loaded with 1.O mmol of LDH and 1.Ommol (3) Allmann, R.Acta Crystallogr., Secr. 8 1968, 824, 972. of alkyl halide was passed through the LDH under a flow of (4) Ingram, L.:Taylor, H. F. W.Mineral. Mag 1967, 36, 465. (5) Allmann, R. Chimia 1970, 24, 99. helium to allow for a contact time of 0.19 s. The products were (6) Gastuche, M. C.; Brown, G.; Mortland, M. M. Clay Miner. 1967, 7, condensed and analyzed by gas chromatography. 177. As is illustrated in Figure 1 for n-butyl bromide and 3(7) Brindley, G. W.; Kikkawa, S.Am. Mineral. 1979, 64, 836. methylbutyl bromide, halide exchange between alkyl bromides (8) Miyata, S.;O h d a , A. Clays Clay Miner. 1977, 25, 14. (9) Taylor, R. M. Clay Miner. 1984, 19, 591. in toluene and intercalated iodide ions in the LDH followed (10) Miyata, S. Clays Clay Miner. 1983, 31, 305.

1).

(11) Lal, M.; Howe, A. T. J. Solid Srate Chem. 1981, 39, 337. (12) Kruissink, E. C.; van Reijen, L. L.; Ross,J. R. H. J. Chem. SOC., Faraday Trans. 1981, 77, 649. (13) Reichle, W. T. J . Card 1985, 94, 547.

(14) Bochm, H. P.; Steinle, J.; Vieweger, C. Angew. Chem., Inr. Ed. Engl. 1977, 16, 265.

(15) Lal, M.; Howe, A. T. J. Solid State Chem. 1981, 39, 368.

0002-7863/86/ 1508-0541%01.50/0 0 1986 American Chemical Society

J . Am. Chem. Soc. 1986,108, 542-543

542

Table 11. Reaction of Gaseous n-Butyl Bromide with Intercalated Halide Ions in Zn2Cr(OH)6X.2H20” intercalated halide t e m..n OC I 150 CI 150 CI 140 c1 130 CI 90

C,HoX vield. % ’ - , . 80 80 71 60 33

~~

“One millimole of butyl bromide was passed over 1 mmol of LDH a t a contact time of 0.19 s and the net yields were determined. The L D H was predried a t 150 OC for 2 h under argon.

pseudo-first-order kinetics over the initial stages of the reaction. As the extent of reaction proceeded beyond -3O%, the rate decreased and eventually became very low above 80% reaction. It is noteworthy, however, that the reaction could be forced essentially to completion by using an excess of LDH. Initial pseudo-first-order rate constants, normalized per unit surface area of LDH, are provided in Table I for several alkyl bromides. Reaction was more facile when the LDH was predried at 150 O C than at 25 OC, even though the mobility of the intercalated halide ion should decrease with decreasing hydration. Also, the size of the alkyl group had little or no effect on reactivity. The possibility that halide exchange for alkyl bromides in the condensed state involves dissolution of the LDH was precluded by the observation that exchange also occurred for alkyl halides in the vapor state. Table I1 summarizes the yields of butyl halide obtained by reaction of gaseous n-butyl bromide with the iodide and chloride exchange form of the LDH. Significant yields were obtained even at 90 OC. Although LDH’s are potentially basic, we observed no evidence for olefin formation through hydrodehalogenation of the alkyl halide. The layer charge density of Zn2Cr(OH)6.X-2H20requires the presence of one gallery halide ion per 16.5 A* of basal surface. Since the ionic radii of I- and Cl- are 2.16 and 1.81 A, respectively, there is insufficient free volume between gallery ions to allow intracrystalline adsorption of alkyl halide. Therefore, the halide exchange reactions are confined to occurring at external basal and edge surfaces. Because the morphology of our LDH crystals is platelike with a platelet thickness of about 500 &Is a negligible fraction (80%) of the intercalated halide ions are capable of migrating to external edge surfaces for reaction with substrate. In addition, the pseudo-first-order kinetics observed up to 30% reaction suggest that the halide ions near edge sites are readily transported to external surfaces for reaction. The ability of the substrate to adsorb a t edge surfaces is another important aspect of the observed reactivity. We tentatively propose that the approximately 2-fold increase in reactivity which occurs upon increasing the drying temperature of the LDH from 25 to 150 OC arises from the removal of more water from the edge surfaces and the enhancement of alkyl halide adsorption. Further evidence for water competing for adsorption sites is provided by the observation that reaction essentially ceases when liquid water is added to the reaction mixture under condensed-phase conditions. Our results suggest that layered double hydroxides are potentially useful compounds for supporting anionic reagents and for designing new classes of crystalline solid-state catalysts. Although the galleries of LDHs are effectively “stuffed” and do not permit intracrystal adsorption of simple organic substrates, the intercalated anions are accessible for reaction of substrate at edge sites. Larger, more complex anions with charge densities lower than those of the halide ions studied here should be even more reactive. Future studies will focus on intercalated metal complex anions as catalysts and photocatalysts.

-

Acknowledgment. The support of this research by the National Science Foundation through Grant CHE-8306583 is gratefully acknowledged. Also, we thank the Michigan State University Center for Fundamental Materials Research for financial support. 0002-7863/86/1508-0542$01 SO10

Observation of a Spin-Peierls Transition in the Linear Chain Compound Aqua[N- (salicy1aldiminato)glycinatolcopper(11) Hemihydrate William E. Hatfield,* Jeffrey H. Helms, Brian R. Rohrs, and Leonard W. ter Haar Department of Chemistry, University of North Carolina, Chapel Hill, North Carolina 27514 Received October 15. I985 The Peierls distortion’ of a quasi-one-dimensional system containing paramagnetic transition-metal ions has not been realized experimentally prior to this report. Some low-dimensional conductors2 undergo a regular electronic Peierls (RP) transition to an insulating ground state. The spin analogue of the R P transition, the spin-Peierls (SP) transition, may arise in electrically insulating, antiferromagnetically coupled, uniformly spaced spin chains. Two types of compounds (TTF-MX4C4(CF3),,M = Cu or Au, X = S or Se,3a-cand MEM-(TCNQ), [MEM is methylethylm~rpholinium]~~] exhibit the SP transition, and it has been suggested, but not confirmed, for other^.)^,^ SP behavior has been observed in chain compounds in which the spins are located on large, flat organic molecules, but not in antiferromagnetically coupled chains4 in which the spins are localized on transition-metal centers. We have identified a linear chain complex with metal-ion-based spins which exhibits magnetic properties characteristic of an SP transition. The compound is aqua[N-(salicylaldiminato)glycinato]copper(II) hemihydrate, CuNSG. The criteria for selection of a candidate for the distortion are as follows: the chain should have ligand bridged paramagnetic metal ions to permit antiferromagnetic interactions, the structural features of the chain should allow strong 3-D interchain phonon interactions, and the chains should be magnetically isolated from one another to minimize interchain magnetic interactions which may lead to long-range 3-D magnetic ordering. Coordination of copper(I1) in CuNSG is square pyramidal. The basal plane is formed by the donor atoms of the tridentate Schiff base and coordination of one water molecule,’ and the apical position is filled by the second carboxylate oxygen from a neighboring molecule to form the chain link for superexchange. Neighboring chains pack antiparallel (Figure 1) with a resultant interweaving of molecular units. This interweaving allows for good interchain phonon interaction, yet interchain magnetic superexchange paths are not present. Magnetic susceptibility measurements were made in the range 1.8-60 K by using a vibrating sample magnetometer and an applied field of 0.1 T.6 Magnetization was measured as a function of applied magnetic field at a number of temperatures from 1.3 to 4.2 K.’ The g,,(EPR) = 2.14 was used in the data analysis. Magnetic susceptibility data shown in Figure 2 for a powdered sample exhibit a maximum near 4 K. At approximately 2.2 K the susceptibility falls off rapidly, too rapidly to be a 3-D magnetic ordering. (1) Peierls, R. E. “Quantum Theory of Solids”; Oxford, 1955. (2) Hatfield, W. E.; ter Haar, L. W. Annu. Rev. Mater. Sci. 1982, 12, 177

and references therein. (3) (a) Bray, J. W.; Interrante, L. V.; Jacobs, I. S.; Bonner, J. C. In “Extended Linear Chain Compounds”; Miller, J. S., Ed.; Plenum: New York; 1982; Vol. 3, and references therein. (b) Jacobs, I. S . ; Bray, J. W.; Hart, H. R.; Interrante, L. V.; Kasper, J. S.; Watkin, G. D.; Prober, D. E.; Bonner, J. C. Pbys. Reu. B 1976,14,3036.(c) Northby, J. A,; Groenendijk, H. A.; de Jongh, L. J.; Bonner, J. C.; Jacobs, I. S.; Interrante, L. V. Pbys. Reu. B 1982, 25, 3215. (d) de Jongh, L. J. In “Magneto-Structural Correlations in Exchange Coupled Systems”; Willett, R. D., Gatteschi, D., Kahn, 0.. Eds.; Reidel: Dordrecht, Holland; 1985. (4)Hatfield, W. E.; Esta, W. E.; Marsh, W. E.; Pickens, M. W.; ter Haar, L. W.; Weller, R. R. In ‘Extended Linear Chain Compounds”; Miller, J. S., Ed.; Plenum: New York, 1982; Vol. 3 and references therein. (5) Ueki, T.; Ashida, T.; Sasada, Y.; Kakudo, M. Acta Crystallogr. 1967, 22, 870. (6)Corvan, P. J.; Estes, W. E.; Weller, R. R.; Hatfield, W. E. Inorg. Chem. 1980,19, 1297. (7) Rubin, L. G.; Wolff, P. E. Pbys. Today 1984,37.

0 1986 American Chemical Society