Subscriber access provided by READING UNIV
Article
Nanocellulose from Spinifex as an Effective Adsorbent to Remove Cadmium(II) from Water Priyanka R. Sharma, Aurnov Chattopadhyay, Sunil K Sharma, LiHong Geng, Nasim Amiralian, Darren J. Martin, and Benjamin S. Hsiao ACS Sustainable Chem. Eng., Just Accepted Manuscript • DOI: 10.1021/ acssuschemeng.7b03473 • Publication Date (Web): 23 Jan 2018 Downloaded from http://pubs.acs.org on January 24, 2018
Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.
ACS Sustainable Chemistry & Engineering is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.
Page 1 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Sustainable Chemistry & Engineering
1
Nanocellulose from Spinifex as an Effective Adsorbent to Remove
2
Cadmium(II) from Water
3 4
Priyanka R. Sharma1, Aurnov Chattopadhyay2, Sunil K. Sharma1, Lihong Geng1,
5
Nasim Amiralian3, Darren Martin3, Benjamin S. Hsiao1*
6 1
7
Department of Chemistry, Stony Brook University, 100 Nicolls Road, Stony Brook, New York 11794-3400, United States
8 2
9 10 11
3
University High School, 4771 Campus Dr., Irvine, CA 92612 United States
Australian Institute for Bioengineering and Nanotechnology, Corner College and Cooper Rds, The University of Queensland, QLD 4072, Australia
12 13 14 15 16 17 18 19 20 21 22
* Corresponding author E-mail:
[email protected]; Tel: +1(631)632-7793
23 1 ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
24
Abstract
25
Nanocelluloses, in the form of carboxycellulose nanofibers, with low crystallinity (CI ~
26
50 %), high surface charge (-68 mV) and hydrophilicity (static contact angle 38°), were prepared
27
from an untreated (raw) Australian spinifex grass using the nitro-oxidation method employing
28
nitric acid and sodium nitrite. The resulting nanofibers (NOCNF) were found to be an effective
29
medium to remove Cd2+ ions (cadmium(II)) from water. For example, a low concentration of
30
NOCNF suspension (0.20 wt%) could remove Cd2+ ions over a large concentration range (50-
31
5,000 ppm) in a relatively short time period (≤ 5 minutes). The results showed that at low Cd2+
32
concentrations (below 500 ppm), the remediation mechanism was dominated by interactions
33
between carboxylate groups on the NOCNF surface and Cd2+ ions, which also acted as a
34
crosslinking agent to gel the NOCNF suspension. At high Cd2+ concentrations (above 1,000
35
ppm), the remediation mechanism was dominated by the mineralization process of forming
36
Cd(OH)2 nanocrystals, which was verified by TEM and WAXD. Based on the Langmuir
37
isotherm model, the maximum Cd2+ removal capacity of NOCNF was around 2,550 mg/g,
38
significantly higher than those of any adsorbents reported in the literature. NOCNF exhibited the
39
highest removal efficiency of 84%, when the Cd2+ concentration was 250 ppm. This study
40
demonstrated a simple pathway to convert underutilized biomass into valuable absorbent
41
nanomaterials that can effectively remove cadmium(II) ions from water.
42 43 44
Keywords Spinifex, carboxycellulose, nanofibers, cadmium(II) removal
45
2 ACS Paragon Plus Environment
Page 2 of 50
Page 3 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
46
ACS Sustainable Chemistry & Engineering
Introduction
47 48
Cadmium is one of the top ten chemicals posing a major public health problem to the
49
society mainly through water contamination.1 In specific, cadmium is a confirmed carcinogen,
50
mutagen and teratogen.2,3 As cadmium is a common component in many electronic devices and
51
other products, such as batteries, solar cells, paints and pigments,4 it can enter the water sources
52
through industrial waste and run-offs. When human is exposed to cadmium by consumption of
53
contaminated foods or water,5 cadmium can be adsorbed by the lungs or gastrointestinal tract and
54
transported in the bloodstream to other parts of body and accumulated in the liver and kidneys.
55
The biochemical pathways indicate that cadmium can bind to proteins, non-protein sulfhydryl
56
groups and various other macromolecules, such as metallothionein, in kidneys.6 According to a
57
report from the Agency for Toxic Substances and Disease Registry (ATSDR),5 the acute oral
58
toxicity dose of cadmium is in between 1,500 and 8,900 mg (i.e., 20 and 30 mg/kg) that would
59
lead to human fatalities. Although fatalities due to the cadmium exposure are rare, even a short-
60
term exposure is known to cause severe gastrointestinal irritation, resulting in vomiting,
61
abdominal pain and diarrhea.5 There have been several recent studies reporting the increasing
62
level of cadmium contaminant in some regions of Africa, Asia and South America.7-9 The
63
problem is not unique only in these regions, whereas similar challenges also exist in other parts
64
of the world. It is thus imperative to identify sustainable, cost-effective and environmental-
65
friendly solutions to deal with this challenge.
66 67
The goal of this study is to demonstrate that carboxycellulose nanofibers (CNF)
68
extracted from a raw biomass by the newly developed nitro-oxidation method can be used as an
3 ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
69
effective adsorbent to remove cadmium(II) ions from water. This approach represents a
70
sustainable and cost-effective solution to tackle the heavy metal contamination problems (such as
71
cadmium) in drinking water. In previous studies, nanocelluloses prepared by acid hydrolysis and
72
oxidation methods (e.g. carboxymethylation, TEMPO) have been utilized as means to take out
73
heavy metal ions from water. For example, nanocrystalline cellulose (CNC) produced by acid
74
hydrolysis, incorporated with succinic acid, was used to remove lead(II) and cadmium(II) ions
75
from water;10 CNF containing carboxylate groups prepared by oxidation methods was also used
76
for chromium(III), nickle(II) and uranyl(II) ions removal.11,12 In addition, thiol modified CNF
77
was found to be effective for chromium(VI) and lead(II) removal,13 and amine-modified CNC
78
was capable of remove negatively charged chromium(VI) metal ions from water.14
79 80
Recently, Carpenter et al. reported the properties and life cycle assessment of different
81
nanocelluloses and compared them with carbon nanotubes (CNT)15. Thakur et al. also described
82
the applications of cellulosic derivatives for water purification and compared their effectiveness
83
with that of CNT.16 Both studies showed that CNF appeared to be a superior adsorption medium
84
over CNT for water purification, due to CNF’s higher functionality, lower cost, greater
85
sustainability and better safety. In addition, CNF has been shown to be a new and improved
86
barrier material for membrane applications, due to its good chemical resistance, hydrophilicity
87
(leading to low fouling tendency) and high porosity (leading to high flux). For example, in our
88
laboratory, thin-film nanofibrous composite (TFNC) membranes, containing multi-layered
89
fibrous scaffolds including a barrier layer made of TEMPO mediated CNF (diameter ~ 5 nm), an
90
electrospun polyacrylonitrile (PAN) nanofibrous mid-layer (diameter ~ 150 nm), and a non-
91
woven polyethylene terephthalate (PET) substrate (diameter~ 20 µm), were demonstrated. These
4 ACS Paragon Plus Environment
Page 4 of 50
Page 5 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Sustainable Chemistry & Engineering
92
membranes exhibited a significantly higher flux (i.e., 2-10 X) for separation of oil/water
93
emulsions than commercial ultrafiltration (UF) membranes with similar rejection capability.17-20
94 95
There are many other naturally occurring sorbent materials that have also been
96
demonstrated to be able to remove small contaminants, such as heavy meal ions and dye
97
molecules, from water.21-27 For example, materials such as ZnO, AgO, TiO2 and alumina,
98
especially in the nanoscale form, have all been shown to be effective adsorption media for water
99
remediation.28-43 From the sustainability perspective, we are particularly interested in the use of
100
underutilized biomasses, such as agriculture waste, grass and weed, as resources to extract
101
valuable nanomaterial (CNF) for water purification because of their abundance and up-cycling
102
potential.
103 104
In this study, the chosen biomass is a raw (untreated) grass from Australia, named
105
spinifex. There are 69 species of spinifex grasses (genus Triodia) in the arid/semi-arid regions of
106
Australia, which covers over one quarter of the continent.44 These grasses are abundant but
107
underutilized. There are plenty of other similar arid grasses exist in Africa, Asia and South
108
America, where many of these regions are also experiencing the cadmium contamination
109
problems 7-9 due to the rapid development of electronic industry. Hence, the goal of this study is
110
to demonstrate that spinifex grass, as a model system for other arid grasses, is a good biomass
111
source to extract functional carboxycellulose nanofibers, whereby the extracted nanofibers could
112
be used as effective adsorbent media to remove cadmium ions from water.
113
5 ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
114
It has been reported that typical spinifex grass has a high content of hemicellulose (~44
115
%), where this characteristics might lead to an easy nanofiber fibrillation tendency when treated
116
with mild alkali conditions followed by a mechanical process (e.g. high pressure
117
homogenization).45,46 The resulting cellulose nanofibers have been successfully demonstrated as
118
an ingredient for nanopaper with high toughness, and as an efficient reinforcement for latex
119
natural rubber and thermoplastic polyurethane nanocomposites.45,47,48 However, spinifex
120
nanofibers produced by using the above process (combined alkali and homogenization
121
treatments) were found to possess no or small surface charge, where their utility as an adsorbent
122
material for water purification is limited.
123 124
To extract CNF from untreated spinifex grasses, we employed the nitro-oxidation
125
method, involving the mixtures of nitric acid and sodium nitrite. This method has been
126
successfully used to prepare charged CNF (abbreviated as NOCNF hereafter) directly from
127
untreated (or raw) jute fibers,49. Nitro-oxidation is a simple approach that can oxidize biomass
128
and produce carboxylated nanocellulose with significant reduction in chemicals, water, and
129
energy consumption. In addition, the effluent from the nitro-oxidation treatment can be recycled
130
to nitrogen-rich fertilizer, thus offering great potential to advance the nexus of food, energy and
131
water. Recently, carboxylated cellulose nanocrystals with a maximum zeta potential of -45 mV,
132
have also been extracted using the hydrothermal treatment of MCC (microcrystalline cellulose)
133
in the presence of nitric acid and hydrochloric acid.50 We envision that the use of nitro-oxidation
134
method to extract functional nanocelluloses will become more popular due to its simplicity.
135
6 ACS Paragon Plus Environment
Page 6 of 50
Page 7 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Sustainable Chemistry & Engineering
136
In the present work, the effectiveness of NOCNF extracting from spinifex to remove
137
heavy metal ions from water was demonstrated in the study of Cd2+ removal. The extracted
138
NOCNF was found to have medium crystallinity (CI = 53 %), high surface charge (-68 mV),
139
carboxylate content (0.86 mmol/g) and hydrophilicity (static contact angle = 38°). The
140
mechanism of Cd2+ removal by NOCNF was explored by using the combined Fourier transform
141
infra-red (FTIR) spectroscopy, scanning electron microscopy/ energy dispersive X-ray
142
spectroscopy (SEM/EDS), confocal microscopy and transmission electron microscopy (TEM)
143
techniques to characterize the floc coagulant formed upon the mixing of metal ion solutions at
144
different concentrations and a NOCNF suspension (0.2 wt%). The results indicated that at low
145
Cd2+ concentrations (below 500 ppm), the remediation process was dominated by the
146
interactions between Cd2+ ions and COO- groups on the NOCNF surface, where the adsorption
147
pathway prevails. In a way, Cd2+ ions also behaved as an effective crosslinking agent to gel
148
NOCNF in suspension. At high Cd2+ concentrations (above 1,000 ppm), the remediation
149
mechanism was dominated by the mineralization of cadmium hydroxide crystals within the
150
gelled NOCNF scaffold. The combination of these two processes greatly enhanced the
151
adsorption capacity of NOCNF.
152 153
The quantitative determination of the adsorption capacity of NOCNF against the Cd2+
154
ions was accomplished by the static adsorption study using the inductively coupled plasma mass
155
spectroscopy (ICP-MS) technique with different cadmium concentrations and under varying pH
156
levels. It was found that NOCNF possessed a maximum removal capacity (Qm) of 2550 mg/g,
157
which, to the best of our knowledge, is about 40% higher than the most effective adsorbent
158
reported in the literature.51 Finally, we demonstrated that the NOCNF-cadmium floc containing
7 ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
159
mineralized cadmium hydroxide could be easily filtered using the low-cost gravity-driven
160
microfiltration or decantation methods. We truly believe that the simple nitro-oxidation approach
161
to extract functional carboxylated nanocelluloses from underutilized raw biomass, such as
162
spinifex grass, can provide a practical pathway to tackle the toxic metal ions (such as
163
cadmium(II)) contamination problems for drinking water purification.
164 165
Experimental
166 167
Materials
168 169
Spinifex grass was obtained from The University of Queensland, Australia. Nitric acid
170
(ACS reagent, 70 %), sodium nitrite (ACS reagent ≥ 97 %), sodium bicarbonate, cadmium
171
nitrate heptahydrate, sodium hydroxide, hydrochloric acid (36% assay) were purchased from
172
Fisher Scientific. The above chemicals were used without further purification. Sodium nitrite,
173
nitric acid, sodium bicarbonate and spinifex grass were used for the preparation of NOCNF,
174
where cadmium nitrate heptahydrate, sodium hydroxide and hydrochloric acid were used for the
175
cadmium remediation studies.
176 177
Preparation and Characterization of NOCNF
178 179
NOCNF were prepared from spinifex grass using the nitro-oxidation method, which has
180
been reported earlier by us.49 In brief, 2 g of water washed spinifex grass was placed in a three-
181
neck round bottom flask, where 10 mL of nitric acid (65-70 wt%, 0.239 mol) was slowly added
8 ACS Paragon Plus Environment
Page 8 of 50
Page 9 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Sustainable Chemistry & Engineering
182
until the grass was completely soaked. Subsequently, 0.028 mol of sodium nitrite was added to
183
the mixture under a continuous stirring (using a magnet stirrer). Upon the addition of sodium
184
nitrite, red fumes were generated. To prevent the escape of these red fumes, the mouths of the
185
round bottom flask were immediately closed. This reaction was allowed to continue at 50°C for
186
12 h, and then the reaction was quenched by adding 250 mL of water. After that, the reaction
187
mixture was transferred into a beaker, and further quenched by adding 250 mL of distilled water.
188
The suspended product was allowed to settle down at the bottom of the beaker, where the upper
189
portion was decanted off to remove the excess acid. The above decantation procedure was
190
repeated 2-3 times until fibers started to suspend in water. In the next stage, the fiber suspension
191
was centrifuged at 3,000 xg for 10 min, until the pH of the supernatant reached above 2.5.
192
Subsequently, the bottom suspension was transferred to a dialysis bag (6-8 kDa) in deionized
193
water for 4-5 days until the conductivity of water reached below 5 µS. After dialysis, the
194
suspension was again centrifuged at 3,000 xg for 5 min, to separate microsized and nanosized
195
fibers. The pH level of the resulting NOCNF suspension was found to be 5.30, which might be
196
due to the presence of remnant (unconverted) carboxyl acid groups in the NOCNF. The yield of
197
carboxycellulose nanofibers obtained by the above procedure was 10 wt% and that of
198
carboxycellulose microfibers was 20 wt%. The carboxyl groups (COOH) on NOCNF were
199
converted to carboxylate groups (COONa) by treating the fiber suspensions with 8% sodium
200
bicarbonate solution at room temperature for 30 min.
201 202
The functional groups on the NOCNF surface were determined using Fourier transform
203
infrared (FTIR) spectroscopy (PerkinElmer Spectrum One instrument-ATR mode), 13C CPMAS
204
NMR (Bruker Utrashield 500WB plus), conductometric titration and Zeta probe analyzer
9 ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
205
(Colloidal Dynamics) instruments. The morphology, polydispersity and crystal structure of
206
NOCNF were characterized by transmission electron microscopy (TEM, FEI Tecnai G2 Spirit
207
BioTWIN instrument), scanning electron microscopy (SEM, Zeiss LEO 1550 SFEG-SEM) with
208
energy dispersive X-ray spectroscopy (EDS) capability, and wide-angle X-ray diffraction
209
(WAXD, Benchtop Rigaku MiniFlex 600) techniques. The specific surface area of NOCNF was
210
measured by Novatouch LX2 (Quantachrome Instruments). The contact angle of NOCNF film
211
was measured using the Future Digital Scientific Corp. (FD) contact angle instrument (Model no.
212
OCA 15 EC). Descriptions of the above instruments and corresponding sample preparation
213
schemes for characterization are listed in Supporting Information.
214 215
Determination of Cadmium(II) Remediation Mechanism and Maximum Removal Capacity
216 217
The cadmium(II) remediation mechanism by NOCNF was determined by the following
218
experiments. Cd2+ solutions with concentrations ranging from 50 to 5,000 ppm were prepared,
219
which were subsequently mixed with a NOCNF suspension of fixed concentration. In specific, a
220
2 mL of 0.2 wt% NOCNF suspension was mixed with a 2 mL of Cd2+ solution at different
221
concentration. Upon mixing, a floc appeared and precipitated to the bottom of the vessel by
222
manual shaking. The non-flocculated portion was diluted by a factor of 1,000 to reach the
223
dilution level below 100 ppb to characterize the removal efficiency, where the flocculated
224
portion was separated by using a 0.1µ size microfiltration filter. The extracted floc sample,
225
containing aggregates of cadmium hydroxide and NOCNF, was characterized by TEM,
226
SEM/EDS, WAXD, and confocal microscopy (Leica TCS SP8X, also described in Supporting
227
Information).
10 ACS Paragon Plus Environment
Page 10 of 50
Page 11 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Sustainable Chemistry & Engineering
228 229
The adsorption efficiency and adsorption capacity of NOCNF against cadmium(II) were
230
determined as follows. The non-floc portion, after dilution with a 2 wt% nitric acid solution to
231
the level below 100 ppb, while maintaining the same pH, was characterized by the inductively
232
coupled plasma mass spectroscopy (ICP-MS) technique (Supporting Information). The
233
adsorption efficiency for NOCNF was calculated based on the difference in Cd2+ concentration
234
before and after the mixing with the NOCNF suspension divided by the original Cd2+
235
concentration (Ce). This efficiency was a function of the Cd2+ concentration. To determine the
236
adsorption capacity of NOCNF, an ideal adsorption capacity was first calculated based on the
237
available mass (grams) of NOCNF in suspension and the available Cd2+ ions. The experimental
238
adsorption capacity (Qe) was the product of the adsorption efficiency and the ideal adsorption
239
capacity. As a result, the experimental adsorption capacity of NOCNF was also a function of the
240
Cd2+ concentration. The effect of pH value on the cadmium(II) adsorption efficiency by NOCNF
241
was further evaluated. In this study, a constant 10,000 ppm solution of cadmium(II) at different
242
pH values (3, 5, 7, 9, and 11) were prepared for the mixing with the 0.2 wt% NOCNF
243
suspension.
244 245
The maximum adsorption or removal capacity (Qm) of NOCNF against cadmium(II) was
246
determined using the Langmuir Isotherm model, which is based on a monolayer adsorption on
247
the active site of adsorbent and has the following expression:
248
ଵ
= ொ + ொ ொ
Eq. 1
11 ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
249
where Ce is the equilibrium (or original) concentration of cadmium(II) and Qe is the adsorption
250
capacity of cadmium(II) by NOCNF at equilibrium. The value of Qm (and b – the Langmuir
251
constant) was calculated from the slope of the linear plot based on Ce/Qe versus Ce.52
252 253
Results and Discussion
254 255
Characterization of NOCNF Extracted from Spinifex Using the Nitro-Oxidation Method
256 257
Figure 1(i) illustrates the FTIR spectra of untreated but water-washed spinifex grass and
258
extracted NOCNF using the nitro-oxidation method. In these spectra, the characteristic peaks of
259
cellulose at 3340 cm-1 due to the O-H stretching and 2900 cm-1 due to the CH and CH2 stretching
260
were seen. The prominent peak (highlighted in yellow) in NOCNF at 1581 cm-1 was indicative of
261
the carboxylate groups, which confirmed the conversion of -CH2OH at the C6 position in the
262
anhydroglucose unit to -COO-. Other peaks at 1372, 1150, 1100, and 1030 cm-1 were due to the
263
stretching and bending vibrations in the glycosidic bonds of cellulose. In the FTIR spectrum of
264
untreated spinifex grass, the peaks at 1739, 1515, 1460, 1240 and 810 cm-1 could be attributed to
265
the symmetrical streching of the C=C bond in aromatic groups of lignin, xylan and glucomannan
266
of hemicellulose.
267 268
It was interesting to note that the intensity of the peak assosiated to the C-H stretching
269
groups at 2900 cm-1 in NOCNF was found to be decreased, while the intensity of COONa peak
270
at 1581 cm-1 was notably increased, when compared to those in untreated spinifex grass. This
271
further confirmed the oxidation of anhydroglucose units at the C6 position by the nitro-oxidation
12 ACS Paragon Plus Environment
Page 12 of 50
Page 13 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Sustainable Chemistry & Engineering
272
method. The significant decrease (or disappearance) in intensity at 1739, 1515, 1460, 1240, and
273
810 cm-1, also verified that the nitro-oxidation method effectively reduced or even removed the
274
hemicellulsoe and lignin content from the cell walls of spinifex grass. Table 1 summarizes some
275
physical and chemical properties of NOCNF extracted from spinifex using the nitro-oxidation
276
method. It was seen that the carboxylate content of spnifex-based NOCNF measured by the
277
conductometric tititration method was 0.86 mmol/g; the surface charge of NOCNF in suspension
278
measured by zetaprobe analyzer was -68 mV; and the specific surface area obtained for the
279
freeze dried NOCNF sample was 5.7 m2/g (this was comparatively lower than that of NOCNF
280
obtained from wood, algae and bacetrial cellulose using other extraction methods,52 which was
281
probably due to a lower degree of polymerization by using the nitro-oxidation method). In
282
addition, the static contact angle of the extracted NOCNF film was 38° (Figure S1 in Supporting
283
Information), indicating the hydrophillic nature of NOCNF.
284 285
Solid state
13
C CPMAS NMR spectra of untreated spinifex grass and the extracted
286
NOCNF are shown in Figure 1(ii). The spectrum of spinifex grass (Figure 1(ii)A) clearly
287
indicated the presence of cellulose, hemicellulose, and lignin components. For example, the
288
small peaks at 21.8 and 173 ppm could be attributed to the methyl and carboxyl carbons in the
289
acetyl groups of glucoroxylans in hemicellulose, whereas the small peak at 56.6 ppm was due to
290
the methoxyl (-OCH3) carbons in lignin.54 In this spectra (spinifex grass), the presence of
291
cellulose was also evident: the peak at 104.60 ppm was due to the C1 carbons, the peaks at 89.4
292
and 84.1 ppm (doublet) were due to crystalline and amorphous regions of the C4 carbons, and
293
the sharp doublet peaks with highest intensity in between 72.4-75.2 ppm, could be contributed to
294
the C2, C3 and C5 carbons. The doublet peaks at 65.2 and 63 ppm were due to the crystalline
13 ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
295
and amorphous regions of the C6 carbons in the cellulose component of spinifex. However, in
296
extracted NOCNF, the
297
difference. For example, the disappearance of peaks at 153, 56.6 and 21.4 ppm, corresponding
298
to the C3, C4 carbons of syringyl units of lignin and methyl groups of glucoroxylans in
299
hemicellulose, confirmed the significant reduction/removal of lignin and hemicellulose content
300
in spinifex grass by the nitro-oxidation method. The intensity increases and broadening of the
301
carbonyl peak at 173 ppm, along with the reduction in the amorphous region of the C6 peak at
302
about 63 ppm, provided the evidence of oxidation of the cellulose moiety at the C6 position.
303
Interestingly, the crystalline peaks of the C6 carbons (65.2 ppm) and C4 carbons (89 ppm) all
304
became sharper in NOCNF, indicating that the oxidation mainly took place in the amorphous
305
region of cellulose. These analyses were consistent with the analysis of FTIR spectral results.
13
C CPMAS NMR spectrum (Figure 1(ii)B) exhibited some notable
306 307
WAXD measurements of spinifex grass and extracted NOCNF were also carried out and
308
the results are illustrated in Figure 2(i). These patterns indicate that both samples exhibited the
309
characteristic signature of a cellulose I structure, with three distinct diffraction peaks at 2θ angles
310
of 16.64° (spinifex)/16.86°(NOCNF), 22.45°(spinifex)/22.77°(NOCNF), and 34.80°, which
311
could be indexed as the (110), (200), and (004) refelctions.55,56 The crystallinity index (CI)
312
calculated using the “Segal equation” (details given in Supplementary Information) was about
313
53% for NOCNF, and about 50% for untreated spinifex grass. The CI of spinifex-based NOCNF
314
was found to be higher than that of jute-based NOCNF49 extracted by the nitro-oxidation
315
method, which was probably due to the different nature of the biomass.
316
14 ACS Paragon Plus Environment
Page 14 of 50
Page 15 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Sustainable Chemistry & Engineering
317
A typical TEM image of NOCNF is shown in Figure 2(ii), which exhibited long filament-
318
like fibers entangled in a random fashion. Using a modified ImageJ software, it was possible to
319
estimate the average fiber length and fiber width. Based on the measurements from 20 individual
320
filaments, the average NOCNF fiber length was 190 ± 90 nm, the average fiber width was 4.0 ±
321
1.5 nm and the polydispersity index (PDI) was 0.35 ± 0.01 (the results also are listed in Table 1)
322
for the spinifex-based nanocellulose sample extracted by the nitro-oxidation method. The
323
average fiber width was in excellent agreement with that of NOCNF extracted from untreated
324
jute fibers, but the average length was shorter than that from jute.49
325 326
Explore the Cadmium(II) Removal Mechanism by NOCNF
327 328
The remediation mechanism of cadmium(II) by NOCNF was determined by
329
characterization of floc formed the mixing of cadmium(II) solutions at different concentration
330
with a 0.2 wt% NOCNF suspension. The visual examination that elucidates the interactions
331
between NOCNF and Cd2+ ions is shown Figure 3(i), where the left photo was a cadmium(II)
332
nitrate solution (Cd2+~5,000 ppm) that was clear and transparent. However, upon the addition of
333
5 mL of NOCNF suspension, a white precipitate or floc appeared at the bottom of the bottle in a
334
very short period of time (< 2 min) (the right photo in Figure 3(i)). The floc sample contained
335
aggregates of NOCNF and cadmium contaminant, which was analyzed carefully to determine the
336
remediation mechanism at different cadmium(II) concentration.
337 338
FTIR spectra of pure NOCNF and the floc obtained by mixing 500 ppm of cadmium(II)
339
nitrate solution and NOCNF suspension (0.2 wt%) are illustrated in Figure 3(ii). In Figure 3(ii)A,
15 ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
340
the NOCNF spectrum depicted the main characteristic peaks at 3400 cm-1 from the hydroxyl (-
341
OH) stretching, 2883 cm-1 from the C-H symmetrical stretching, 1232 cm-1 from the C-OH
342
bending at the C6 position, 1204 cm-1 from the C-O-C symmetric stretching, and 1581 cm-1 from
343
the COO- stretching. However, the floc spectrum (Figure 3(ii)B) exhibited some notable
344
difference. For example, the COO- stretching peak was shifted to 1630 cm-1 versus the initial
345
1581 cm-1 in NOCNF, which is in agreement with the occurrence of interactions between COO-
346
and Cd2+ ions. As one Cd2+ ion can effectively interact with two COO- groups, cadmium(II) can
347
be considered as a good crosslinking agent for the charged NOCNF particles in water. The peak
348
at 3400 cm-1 in the floc spectrum also displayed a significant broadening and intensification
349
when compared with that of pure NOCNF. As this peak was due to the hydroxyl (-OH)
350
stretching, its broadening and intensification could no longer be attributed only to the presence of
351
water in NOCNF, but due to the formation of cadmium hydroxide (Cd(OH)2), which is discussed
352
later.
353 354
The steady state shear viscosity measurement of the cadmium(II) nitrate aqueous solution
355
(Cd2+=500 ppm), the NOCNF suspension at concentration 0.1 wt%, and the floc portion of the
356
mixture containing Cd2+ ions (500 ppm) and NOCNF (0.1 wt%) in suspension was carried out to
357
understand the interactions between Cd2+ ions and NOCNF. The viscosity results are illustrated
358
in Figure S2 (Supporting Information). It was seen that the cadmium nitrate solution possessed
359
very low viscosity, in which instability was observed at low shear rates. In contrast, the NOCNF
360
suspension (0.1 wt%) behaved as a Newtonian fluid with slight shear-thinning tendency at high
361
shear rates. However, the floc of Cd2+ and NOCNF aggregates displayed a drastic increase in
362
viscosity and pronounced shear-thinning behavior. In fact, the floc portion of the mixture
16 ACS Paragon Plus Environment
Page 16 of 50
Page 17 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Sustainable Chemistry & Engineering
363
behaved exactly like a gel. This observation supported the notion that Cd2+ ions functioned as an
364
effective crosslinking agent to bind negatively charged NOCNF particles together, similar to the
365
hydrogel formation induced by ionic interactions between the oppositely charged molecules.57
366
Furthermore, the enhanced shear-thinning behavior in the floc implied that the total attraction
367
forces between Cd2+ and NOCNF, even through strong ionic interactions, were not sufficiently
368
high to resist the deformation forces at high shear rates. The above viscosity results are
369
complementary to the FTIR results (Figure 3(ii)), also indicating that Cd2+ is an effective
370
crosslinking agent to gel the NOCNF suspension.
371 372
It was interesting to note that the actual Cd2+ adsorption capacity of NOCNF in
373
suspension was much higher than the expected value based on the available carboxylate groups
374
on NOCNF. The very high adsorption capacity was due to the combined effects of cadmium(II)
375
adsorption by the charged NOCNF scaffold (as a polyelectrolyte) and the mineralization of
376
cadmium hydroxide crystals through nucleation and growth pathways. The mineralization of
377
metal ions in polyelectrolyte has been well documented. For example, Hirasawa et al. reported
378
that the mixing of lead sulfate solution with polyethyleimine (PEI) polyelectrolyte could lead to
379
nanosized lead crystals.58 In this system, the PEI component clearly acted as a nucleating agent
380
in the aqueous environment. Initially, no visible changes were observed upon the addition of lead
381
sulfate to the PEI polyelectrolyte. However, with the increasing lead sulfate content, the lead
382
concentration suddenly displayed a sharp decrease, which was termed as the ‘bend point’ by the
383
authors. Subsequently, the tranparent solution became to a milky suspension, containing a large
384
amount of nanocrystals. In the present study, a similar behavior was also observed after the
385
addition of Cd+2 ions into the NOCNF suspension.
17 ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
386 387
The cadmium(II) remediation mechanism by NOCNF was revealed by the SEM/EDS
388
measurements. Figure 4 shows SEM images of two floc samples formed upon the addition of
389
Cd2+ solutions having two different concentrations: (i) 500 ppm and (ii) 1,000 ppm, to the 0.2
390
wt% NOCNF suspension. In Figure 4(i), the image of the floc with lower Cd2+ concentration
391
(500 ppm) exhibited the clear appearance of agglomerated nanofibers, partially covered with
392
white clouds of cadmium compound (as seen in the EDS inset), indicating the adsorption of Cd2+
393
ions onto the NOCNF surface. In fact, no evidence (by X-ray diffraction) of cadmium
394
mineralization was observed at this concentration. The quantitative evidence of the presence of
395
cadmium (Cd) compound was supported by the EDS spectrum, where the carbon (C), oxygen
396
(O) and sodium (Na) peaks were due to NOCNF, and the very large silicon (Si) peak was due to
397
the use of silicon wafer as the support substrate. The similar intensity of the peaks associated
398
with NOCNF and Cd indicated that mass ratio between NOCNF and the adsorbed cadmium was
399
similar. This suggests that at cadmium concentrations ≤500 ppm, the remediation mechanism
400
was mainly due to the adsorption of Cd+2 ions onto the NOCNF surface.
401 402
However, SEM image of the floc sample obtained upon the mixing of a cadmium(II)
403
solution with a higher concentration (1,000 ppm) and the NOCNF suspension showed very
404
different morphology (Figure 4(ii)). In this image, the fiber appearance was less visible, while
405
thick cloudy structures associated with cadmium hydroxide crystals became dominant in some
406
regions. The corresponding EDS spectrum (inset) showed the Cd peak with much higher
407
intensity, while other peaks (C, O, Na and Si) were maintained at the same level. This indicated
408
the mineralization of cadmium hydroxide crystals occurred. It also indicates that the adsorbed
18 ACS Paragon Plus Environment
Page 18 of 50
Page 19 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Sustainable Chemistry & Engineering
409
cadmium on the NOCNF surface acted as a nucleus, which initiated the growth of cadmium
410
hydroxide crystals in the presence of high Cd+2 concentration. In this stage, the remediation
411
mechanism is mainly dominated by the crystal growth of cadmium hydroxide.
412 413
The formation of cadmium hydroxide nanocrystals could be confirmed by Figure 5,
414
which illustrates (A) TEM image and (B) corresponding WAXD profile of the floc sample
415
formed by mixing of 1,250 ppm Cd2+ solution and 0.2 wt% NOCNF suspension at pH = 7. In
416
TEM measurement, the floc sample was not stained with uranyl acetate to avoid the overlap of
417
contrast. In Figure 5A, it was seen that the NOCNF scaffold acted as a nucleating network in the
418
formation of cadmium hydroxide nanocrystals (black dots), where the average size of these
419
nanocrystals was in the range of 3-5 nm. The results are in full agreement with the data reported
420
in the previous literature, where the presence of cellulose nanofibers could induce the formation
421
of metal nanocrystals (ferrite, Ag, Au, ZnO, TiO2).59-61 Figure 5B shows the corresponding
422
WAXD profile of the floc sample in Figure 5A. Distinct diffraction peaks were seen, which
423
could be indexed by the unit cells of Cellulose I structure and cadmium hydroxide. In specific,
424
the peaks at the 2θ angle of 16.86° and 22.77° could be indexed by (110), (200) diffractions from
425
the Cellulose I structure, whereas the peaks at the 2θ angle of 29.2°, 31.9°, 35.4°, 38.9°, 42.8°,
426
48.09°, 55.4°, and 56.4° could be indexed by (001), (200), (220), (131ത), (111), (310), (201) and
427
(421ത) diffractions of cadmium hydroxide, respectively.62
428 429
Confocal images of NOCNF cast from the 0.2 wt% suspension, cadmium nitrate deposit
430
from a 1,000 ppm solution, and a floc sample prepared by mixing the NOCNF suspension and
431
1,000 ppm solution, are shown in Figure 6. Figure 6(i) represents the NOCNF aggregates with
19 ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
432
NOCNF being stained by the acid blue dye, while Figure 6(ii) represents the cadmium nitrate
433
deposit with Cd2+ ions being stained by the LeadmiumTM AM dye (this dye has been commonly
434
used to detect lead or cadmium ions in living cells because of its good binding tendency with
435
these metal ions63). The two dyes have different excitation wavelengths: the acid blue dye has an
436
excitation at λ = 580 nm, and the LeadmiumTM AM dye has an excitation at λ = 405-490 nm. As
437
a result, their imaging by different lasers could be used to differentiate the regions of NOCNF
438
and Cd2+ ions at a macroscopic level. In specific, the laser with a wavelength λ = 580 nm was
439
used to take the image in Figure 6(i), which exhibited the agglomeration of NOCNF rather than
440
individual nanofibers; the laser with wavelength λ = 405-490 nm was used to take the image in
441
Figure 6(ii), exhibiting light shadow of cadmium nitrate deposit. Figure 6(iii) represents the floc
442
sample, prepared by mixing stained NOCNF with the acid blue and stained Cd2+ ions with the
443
LeadmiumTM AM dye, taking at λ = 580 nm. In this image, the same type of red textures (due to
444
the agglomeration of NOCNF) was seen as that in Figure 6(i). However, when imaging the same
445
floc sample at λ = 470 nm (Figure 6(iv)), a very different texture was seen when compared that
446
in Figure 6(ii). In specific, the floc images in Figure 6(iv) exhibited a granular texture (marked
447
by red circles) with the granules having much stronger intensity than the diffuse texture in the
448
image of cadmium nitrate deposit (Figure 6(ii)). This granular texture was also not seen in Figure
449
6(iii), in which the imaging was taken to highlight the stained NOCNF. The granular regions in
450
Figure 6(iv) were due to the clusters of collapsed NOCNF scaffold bonded by cadmium
451
hydroxide nanocrystals. These results further confirmed the occurrence of cadmium hydroxide
452
mineralization within the NOCNF scaffold during the remediation process.
453 454
Determine the Maximum Cadmium(II) Removal Capacity of NOCNF
20 ACS Paragon Plus Environment
Page 20 of 50
Page 21 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Sustainable Chemistry & Engineering
455 456
The maximum removal capacity of NOCNF against cadmium(II) was determined as
457
follows. Based on the procedures outlined in the Experimental section, the ideal adsorption
458
capacity, adsorption efficiency and experimental adsorption capacity (Qe) of NOCNF for the
459
removal of cadmium(II) in the concentration range of 50 – 5,000 ppm were determined, and the
460
results are shown in Table 2. It was found that the adsorption (or removal) efficiency of NOCNF
461
against cadmium(II) in the 50-1,250 ppm region (except 100 ppm) was between 74 and 84 %.
462
However, the efficiency of NOCNF in the 2,500 and 5,000 ppm region was between 14 and
463
17%. Based on Table 2, the values of the original Cd2+ concentration (Ce), experimental
464
adsorption capacity (Qe) and Ce/Qe are summarized in Table 3. It was found that the plot of Qe
465
against Ce almost exhibited a linear relationship (Figure 7(i)). These results were rearranged
466
according to Eq. 1, where the plot of Ce/Qe versus Ce could be fitted with the Langmuir
467
Isotherm model, as shown in Figure 7(ii). The slope of the fit is proportional to the reciprocal of
468
the maximum adsorption capacity (Qm), which was about 2,550 mg/g (R2= 0.986).
469 470
The maximum adsorption capacity (Qm) of the spinifex-based NOCNF was compared
471
with other commercially available and experimental adsorbents, which are listed in Table 4. It
472
was found that the Qm of NOCNF in this study was about 40% higher than the best commercial
473
adsorbent based on magnesium oxide;51 it was also several times higher than those of porous
474
chitosan beads64 and carboxymethyl functionalized cellulose,65 all effective cadmium(II)
475
adsorbents, probably due to the much larger available surface area in NOCNF. The combined
476
advantage of the very large surface to volume ratio (nanofibers) and abundant charged groups
477
(COO-) in NOCNF was even more pronounced when compared to raw wood,66 coffee grounds,67
21 ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 22 of 50
478
agriculture waste (e.g. corn stalk, maize cob and bagasse) and biowaste (e.g. oil cake and shell
479
dust),66-71
480
nanocomposites,82 where the Qm value of spinifex-based NOCNF was significantly higher. In
481
fact, extracted NOCNF also exhibited higher efficiency than the other carboxylated biopolymers,
482
such as carboxylated alginic acid,83 esterified saw dust bearing carboxyl group,84 carboxylated
483
chitosan,85 carboxylated cellulose nanocrystals10 and cellulose nanocrystal modified using
484
sodium succinate.10
synthetic
polymer,72
biochar,73
activated
charcoal,74-80
styofoam,81
and
485 486
The adsorption efficiency of NOCNF for removal of Cd2+ ions from water was found to
487
be pH dependent.
To demonstrated this effect, the adsorption efficiency of NOCNF for
488
cadmium(II) removal was measured at different pH level in a very high Cd+2 concentration
489
(10,000 ppm), where the result is shown in Figure 8. It was found that the highest adsorption
490
efficiency was achieved at pH = 7, which would enable practical applications. This behavior
491
could be explained as follows. At the very low pH values, the effective charge density became
492
lower as some carboxylate groups got turned into neutral carboxylic acid groups, while at very
493
high pH values, some NOCNF could be denatured. The observation of the high adsorption
494
capacity of NOCNF occurred at neutral pH is also consistent with the results obtained from
495
biosorption of olive stones.86
496 497
To further evaluate the usage of NOCNF as an adsorbent material to remove Cd2+ ions
498
from water, a freeze-dried NOCNF sample (in powder form) was used in the following
499
experiment. In specific, 0.056 g of NOCNF was re-dispersed in 150 mL of water, where the pH
500
value of the milky NOCNF suspension (Figure 9(i)) was found to be 5.30 and the corresponding
22 ACS Paragon Plus Environment
Page 23 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Sustainable Chemistry & Engineering
501
conductivity was 30.40 µs. The milky appearance indicated that the re-dispersion of freeze-dried
502
NOCNF powder would take time and was in the microscopic level. However, when 10 mL of
503
cadmium nitrate solution (1,500 ppm) was added to this NOCNF suspension, a precipitation
504
formed rather quickly. For example, after 5 minutes of decanting, the coagulant of NOCNF and
505
cadmium hydroxide crystals completely precipitated to the bottom of the flask (Figure 9(ii)). The
506
removal of cadmium(II) by these freeze-dried NOCNF sample was complete, but the pH value of
507
the suspension in Figure 9(ii) was found to decrease to 4.50 and the conductivity increase to
508
220.4 µs. This might be due to the following reason. Upon the addition of cadmium nitrate
509
solution in the NOCNF suspension, the formation of nitric acid (HNO3) could occur, resulting
510
from the release of nitrate (NO3-) ions from cadmium nitrate and H+ ions from the COOH group
511
of NOCNF (in lower pH value). This reaction would lead to the decrease in pH and increase in
512
conductivity. This observation was quite different from a study of cadmium(II) removal from
513
cadmium acetate solution using olive stones.86 In that study, the precipitation of cadmium
514
hydroxide (Cd(OH)2) crystals took place at pH between 10 and 11, in which the maximum
515
removal efficiency of cadmium(II) was seen. The precipitate in Figure 9(ii) (due to the coagulant
516
of NOCNF and cadmium hydroxide crystals) could be easily removed by gravity driven
517
microfiltration process, where Figure 9(iii) illustrates the transparent solution after filtration
518
using a course filter paper (average pore size around 40 µm).
519 520
Conclusions
521 522
In this study, carboxycellulose nanofibers (NOCNF) extracted from an arid grass spinifex
523
using the nitro-oxidation method were demonstrated to be an effective flocculating or
23 ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
524
coagulating agent for removal of cadmium(II) from water. The maximum adsorption (removal)
525
capacity of the studied NOCNF was found to be 2,550 mg/g, determined by the Langmuir
526
isotherm model using the data from a static adsorption study. This capacity was significantly
527
higher than those reported in the literature for cadmium(II) removal. The removal pathway was
528
found to contain two mechanisms: at low cadmium(II) concentrations (< 500 ppm), the removal
529
was dominated by the charge interactions between the COO- groups and Cd2+ ions, whereas at
530
high cadmium(II) concentrations (> 1,000 ppm), the removal was dominated by the formation of
531
Cd(OH)2 nanocrystals. As Cd2+ ions behaved as an effective crosslinking agent to gel the
532
NOCNF suspension, the precipitate of NOCNF/Cd(OH)2 aggregates could be easily removed by
533
gravity-driven (or very low energy) microfiltration using filters of large pore size (e.g. 40 µm),
534
or by decantation. The nitro-oxidation method was found to be a simple and effective means to
535
extract CNF from spinifex, which could be viewed as a model for many underutilized arid
536
grasses (e.g. agave) or even agriculture waste.
537
adsorbent to purify the cadmium(II) contaminated water because of its very large surface to
538
volume ratio and abundant carboxylate groups. The spinifex-based NOCNF system can be
539
viewed as a mode system to tackle the emerging cadmium pollution problems in many part of the
540
world, where NOCNF can be extracted from a wide range of underutilized biomasses.
The resulting NOCNF is an outstanding
541 542
Supporting Information
543 544
Detailed descriptions on instruments used, such as Fourier transform infra-red 13
545
spectroscopy (FTIR),
C nuclear magnetic resonance (NMR), conductometric titration method,
546
zeta potential measurement, transmission electron microscopy (TEM), scanning electron
24 ACS Paragon Plus Environment
Page 24 of 50
Page 25 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Sustainable Chemistry & Engineering
547
microscopy (SEM), wide-angle X-ray diffraction (WAXD), surface area measurement by the
548
Brunauer-Emmett-Teller (BET) method, confocal microscopy, inductively coupled plasma mass
549
spectroscopy (ICP-MS), contact angle measurement (including a figure illustrating the contact
550
angle measurement of NOCNF extracted from spinifex fibers) and rheological measurements
551
with figure showing the steady state shear viscosity data of cadmium(II) nitrate solution,
552
NOCNF suspension, and the floc portion of the cadmium(II)/NOCNF mixture.
553 554
Acknowledgments
555 556
The authors would like to thank the SusChEM Program of the National Science
557
Foundation (DMR-1409507) for the financial support. The authors would also like to thank
558
Susan von Horn (iLab-Stony Brook University) and Dr. Chung-Chueh Chang and Ya-Chen
559
Chuang (ThINC facility at AERTC, Stony Brook University, USA) for conducting the TEM
560
measurements, Dr. Jim Quinn (Materials Science and Engineering- Stony Brook University) for
561
the SEM measurements and Dr. David Hirschberg (School of Marine and Atmospheric Science,
562
Stony Brook University) for conducting the ICP-MS analysis.
563 564
References
565
1. Soisungwan, S. Long-term exposure to cadmium in Food and Cigarette Smoke, Liver effects
566 567 568
and Hepatocellular carcinoma. Current Drug Metabolism. 2012, 13(3), 257 – 271. 2. Degraeve, N. Carcinogenic, Tetratogenic and Mutagenic effects of cadmium. Mutat. Res. 1981, 1, 115-135.
25 ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
569
3. Yong, J.; Alan, C.; Robert, S.; Hanan, A. R.; Jack, T.; Thomas, K.; Michael, R.; Dmitry, G.
570
Cadmium is a mutagen that acts by inhibiting mismatch repair. Nature Genet. 2003, 34, 326-
571
329.
572
4. https://www.osha.gov/SLTC/cadmium/ Retrieved on 19th February 2017.
573
5. Agency for Toxic Substances and Disease Registry. 1989. Toxicological profile for
574 575 576 577 578
cadmium. ATSDR/U.S. Public Health Service, ATSDR/TP-88/08. 6. Goyer. R. Toxic effects of metals. In: Amdur, M.O., J.D. Doull and C.D. Klaassen, Eds. Casarett and Doull's Toxicology. 4th ed. Pergamon Press, New York. 1991, 623-680. 7. Anetor, J. Rising environmental cadmium levels in developing countries: threat to genome stability and health. J. Physiol. Sci. 2012, 27(2), 103-15.
579
8. Debajit, D.; Hari, S. Copper (Cu), Zinc (Zn) and Cadmium (Cd) Contamination of
580
Groundwater in Dikrong River Basin, Paumpare District, Arunachal Pradesh, India. IOSR
581
JESTFT 2015, 9(10), 20-23.
582
9. Annabella, G.; Lucas, S.; Lucrecia, F. Cadmium toxicity assessment in juveniles of the
583
Austral South America amphipod Hyalella curvispina. Ecotoxicol. Environmen. Saf. 2012,
584
79, 163-169.
585
10. Yu, X.; Tong, S.; Ge, M.; Wu, L.; Zuo, J.; Cao, C.; Song, W. Adsorption of heavy metal ions
586
from aqueous solution by carboxylated cellulose nanocrystals. J. Environ. Sci. 2013, 25 (5)
587
933–943.
588 589 590 591
11. Srivastava, S.; Kardam, A.; Raj, K. R. Nanotech reinforcement onto cellulose fibers: Green remediation of toxic metals. Int. J. Green Nanotechnol. 2012, 4, 46-53. 12. Ma, H.; Hsiao, B. S.; Chu, B. Ultrafine cellulose nanofibers as efficient removal of UO22+ in water. ACS Macro. Lett. 2012, 1, 213-216.
26 ACS Paragon Plus Environment
Page 26 of 50
Page 27 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Sustainable Chemistry & Engineering
592
13. Yang, R.; Aubrecht, K. B.; Ma, H. Y.; Wang, R.; Grubbs, R. B.; Hsiao, B. S.; Chu, B. Thiol-
593
modified cellulose nanofibrous composite membranes for chromium(VI) and lead(II)
594
adsorption. Polymer 2014, 55, 1167-1176.
595
14. Sing, K.; Arora, J. K.; Sinha, T. J. M.; Srivastava, S. Functionalization of nanocrystalline
596
cellulose for decontamination of Cr(III) and Cr(VI) from aqueous system: Comutational
597
modeling approach. Clean Techn. Environ. Policy 2014, 16.
598 599 600 601
15. Carpenter, A. W.; de Lannoy, C. F.; Wiesner, M. R. Cellulose nanomaterials in water treatment technologies. Environ. Sci. Technol. 2015, 49, 5277-5287. 16. Thakur, V. K.; Voicu, S. I., Recent advances in cellulose and chitosan based membranes for water purification: A concise review. Carbohydr. Polym. 2016, 146, 148-65.
602
17. Wang, R.; Guan, S.; Sato, A.; Wang, X.; Wang, Z.; Yang, R.; Hsiao, B. S.; Chu, B.,
603
Nanofibrous microfiltration membranes capable of removing bacteria, viruses and heavy
604
metal ions. Journal of Membrane Science 2013, 446, 376-382.
605 606 607 608 609 610
18. Ma, H.; Burger, C.; Hsiao, B. S.; Chu, B., Nanofibrous microfiltration membrane based on cellulose nanowhiskers. Biomacromolecules 2012, 13 (1), 180-186. 19. Ma, H.; Burger, C.; Hsiao, B. S.; Chu, B., Ultrafine polysaccharide nanofibrous membranes for water purification. Biomacromolecules 2011, 12 (4), 970-976. 20. Ma, H.; Burger, C.; Hsiao, B. S.; Chu, B., Ultra-fine cellulose nanofibers: new nano-scale materials for water purification. Journal of Materials Chemistry 2011, 21 (21), 7507.
611
21. Gupta, V. K.; Kumar, R., Nayak, A.; Saleh, T. A.; Barakat, M. A. Adsorptive removal of
612
dyes from aqueous solution onto carbon nanotubes: A review. Adv. Colloid Interface Sci.
613
2013, 193-194, 24–34.
27 ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
614
22. Gupta, V. K.; Mittal, A.; Jhare, D.; Mittal, J. Batch and bulk removal of hazardous colouring
615
agent Rose Bengal by adsorption techniques using bottom ash as adsorbent. RSC Adv. 2012,
616
2, 8381–8389.
617 618
23. Gupta, V. K.; Nayak, A.; Agarwal, S. Bioadsorbents for remediation of heavy metals: Current status and their future prospects. Environ. Eng. Res. 2015, 20 (1), 001-018.
619
24. Mittal, A.; Mittal, J.; Malviya, A.; Kaur, D.; Gupta, V. K. Decoloration treatment of a
620
hazardous triarylmethane dye, Light Green SF(Yellowish) by waste material adsorbents. J.
621
Colloid Interface Sci. 2010, 342, 518-527.
(13)
622
25. Gupta, V. K.; Mittal, A.; Jhare, D.; Mittal, J. Batch and bulk removal of hazardous colouring
623
agent Rose Bengal by adsorption techniques using bottom ash as adsorbent. RSC Advances
624
2012, 2, 8381–8389.
625 626
26. Gupta, V. K.; Sharma, S. Removal of Zinc from Aqueous Solutions Using Bagasse Fly Ash -a Low Cost Adsorbent. Ind. Eng. Chem. Res. 2003, 42, 6619-6624
627
27. Mohammadi, N.; Khani, H.; Gupta, v. K.; Amereh, E.; Agarwal, S. Adsorption process of
628
methyl orange dye onto mesoporous carbon material-kinetic and thermodynamic studies. J.
629
Colloid Interface Sci. 2011, 362, 457-462.
630
28. Saravanan, R.; Karthikeyan, S.; Gupta, V. K.; Sekaran, G.; Narayanan, V.; Stephen, A.
631
Enhanced photocatalytic activity of ZnO/CuO nanocomposite for the degradation of
632
textile dye on visible light illumination. Mater. Sci. Eng. C 2013, 33, 91-98.
633
29. Saravanan, R.; Thirumal, E.; Gupta, V. K.; Narayanan, V.; Stephen, A. The photocatalytic
634
activity of ZnO prepared by simple thermal decomposition method at various temperatures.
635
J. Mol. Liq. 2013, 177, 394.
28 ACS Paragon Plus Environment
Page 28 of 50
Page 29 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Sustainable Chemistry & Engineering
636
30. Gupta, V. K.; Jain, R.; Nayak, A.; Agarwal, S.; Shrivastava, M. Removal of the hazardous
637
dye-Tartrazine by photodegradation on titanium-dioxide surface. Mater. Sci. Eng. C 2011,
638
31, 1062-1067.
639
31. Jain, A. K.; Gupta, V. K.; Bhatnagar, A.; Suhas. A Comparative Study of Adsorbents
640
Prepared from Industrial Wastes for Removal of Dyes. Sep. Sci. Technol. 2003, 38 (2), 463-
641
481.
642
32. Saleh, T. A.; Gupta, V. K.
Functionalization of tungsten oxide into MWCNT and its
643
application for sunlight-induced degradation of rhodamine B. J. Colloid Interface Sci. 2011,
644
362, 337-344.
645
33. Saravanan, R.; Sacari, E.; Gracia, F.; Khan, M. M., Mosquera, E.; Gupta, V. K. Conducting
646
PANI stimulated ZnO system for visible light photocatalytic degradation of coloured dyes. J.
647
Mol. Liq. 2016, 221, 1029-1033.
648
34. Rajendran, S.; Khan, M. M.; Gracia, F.; Qin, J. Gupta, V. K.; Arumainathan, S. Ce3+-ion-
649
induced visible-lightphotocatalytic degradation and electrochemical activity of ZnO/CeO2
650
nanocomposite. Sci. Rep. 2016, 6 (31641), 1-11.
651
35. Saravanan, R.; Karthikeyan, S. Gupta, V. K.; Sekaran, G.; Narayanan, V.; Stephen, A.
652
Enhanced photocatalytic activity of ZnO/CuO nanocomposite for the degradation of textile
653
dye on visible light illumination. Mater. Sci. Eng. C 2013, 33, 91-98.
654
36. Saravanan, R.; Thirumal, E.; Gupta, V.K.; Narayanan, V. Stephen, A. The photocatalytic
655
activity of ZnO prepared by simple thermal decomposition method at various temperatures.
656
J. Mol. Liq. 2013, 177, 394-401.
29 ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
657
37. Saleh, T. A.; Gupta, V. K. Synthesis and characterization of alumina nano-particles
658
polyamide membrane with enhanced flux rejection performance. Sep. Purif. Technol. 2012,
659
89 245–251.
660
38. Karthikeyan, S.; Gupta, V. K.; Boopathy, R.; Titus, A.; Sekaran, G. A new approach for the
661
degradation of high concentration of aromatic amine by heterocatalytic Fenton oxidation:
662
Kinetic and spectroscopic studies. J. of Mol. Liq. 2012, 173, 153-163.
663
39. Asfaram, A.; Ghaedi, M.; Agarwal, S.; Tyagib, I.; Gupta, V. K. Removal of basic dye
664
Auramine-O by ZnS: Cu nanoparticles loaded on activated carbon: optimization of
665
parameters using response surface methodology with central composite design. RSC Adv.
666
2015, 5, 18438- 18450.
667
40. Devaraj, M; Saravanan, R.; Deivasigamani, R. K.; Gupta, V. K.; Gracia, F.; Jayadevan, S.
668
Fabrication of novel shape Cu and Cu/Cu2O nanoparticles modified electrode for the
669
determination of dopamine and paracetamol. J. Mol. Liq. 2016, 221, 930–941.
670
41. Hubbard, A. T. (Editor). Encyclopedia of Surface and Colloid Science. 2004.
671
42. Saleh, T. A.; Gupta, V. K. Photo-catalyzed degradation of hazardous dye methyl orange by
672
use of a composite catalyst consisting of multi-walled carbon nanotubes and titanium
673
dioxide. J. Colloid Interface Sci. 2012, 371, 101-106.
674
43. Saravanan, R.; Gupta, V. K.; Mosquera, E.; Gracia, F.; Narayanan, V., Stephen, A., Visible
675
light induced degradation of methyl orange using Ag0.333V2O5 nanorod catalysts by facile
676
thermal decomposition method. J. Saudi Chem. Soc. 2015, 19 (5), 521-527.
677 678
44. Alan F. M. "Grasslands-Spinifex". Te Ara - the Encyclopedia of New Zealand 2009, Retrieved on 31 January 2010.
30 ACS Paragon Plus Environment
Page 30 of 50
Page 31 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Sustainable Chemistry & Engineering
679
45. Amiralian, N.; Annamalai, P. K.; Memmott, P.; Martin, D. J. Isolation of cellulose
680
nanofibrils from Triodia pungens via different mechanical methods. Cellulose 2015, 22(4),
681
2483-2498.
682
46. Amiralian, N.; Annamalai, P. K.; Memmott, P.; Taran, E.; Schmidt, S.; Martin, D. J.
683
Reinforcement of natural rubber latex using lignocellulosic nanofibers isolated from spinifex
684
grass. J. RSC Adv. 2015, 5, 32124–32132.
685
47. Hosseinmardi, A.; Annamalai, P. K.; Wang, L.; Martin, D. J.; Amiralian, N. Reinforcement
686
of natural rubber latex using lignocellulosic nanofibers isolated from spinifex grass.
687
Nanoscale 2017, 9 (27), 9510-9519.
688
48. Mohd Amin, K. N.; Amiralian, N.; Annamalai, P. K.; Edwards, G.; Chaleat, C.; Martin, D. J.
689
Scalable processing of thermoplastic polyurethane nanocomposites toughened with
690
nanocellulose. Chem. Eng. J. 2016, 302, 406-416.
691
49. Sharma, P. R.; Joshi, R.; Sharma, S.K.; Hsiao, B. S. A Simple Approach to Prepare
692
Carboxycellulose Nanofibers from Untreated Biomass. Biomacromolecules 2017, 18(8),
693
2333-2342.
694
50. Cheng, M.; Qin, Z.; Chen, Y.; Ran, Z. Facile one-step extraction and oxidative carboxylation
695
of cellulose nanocrystals through hydrothermal reaction by using mixed inorganic acids.
696
Cellulose, 2017, 24, 3243-3254.
697
51. Cao, C.; Qu, J.; Wei, F.; Liu, H; Song, W. Superb adsorption capacity and mechanism of
698
flowerlike magnesium oxide nanostructures for lead and cadmium ions. ACS Appl. Mater.
699
Interfaces, 2012, 4, 4283-4287.
700 701
52. Wang, J.; Kuo, Y. Preparation of fructose-mediated (polyethylene glycol/chitosan) membrane and adsorption of heavy metal ions. J. Polym. Sci. 2007, 105, 1480-1489.
31 ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
702
53. Stefelova, J.; Slova k, V.; Siqueira, G.; Olsson, R. T.; Tingaut, P.; Zimmermann, T.; Sehaqui,
703
H. Drying and pyrolysis of cellulose nanofibers from wood, bacteria, and algae for char
704
application in oil absorption and dye adsorption. ACS Sustainable Chem. Eng. 2017, 5,
705
2679−2692.
706
54. Reddy, K. O.; Ashok, B.; Reddy, K. R. N.; Feng, Y. E.; Zhang, J.; Rajulu, A. V. Extraction
707
and characterization of novel lignocellulosic fibers from Thespesia lampas plant. Int. J.
708
Polym. Anal. Charact. 2014, 19, 48–61.
709 710 711 712 713 714
55. Isogai, A.; Usuda, M.; Kato, T.; Uryu, T.; Atalla, R. H. Solid-state CP/MAS carbon-13 NMR study of cellulose polymorphs. Macromolecules 1989, 22(7), 3168-1393. 56. Chidambareswaran, P. K.; Sreenivasan, S.; Patil, N. B.; Sundaram, V.; Srinathan, B. X-ray diffraction studies on cotton/jute blends. J. Appl. Polym. Sci. 1976, 20, 3443-3448. 57. Hennick, W. E.; van Nostrum, C. F. Novel crosslinking methods to design hydrogels. Adv. Drug Deliv. Rev., 2012, 64, 223-236.
715
58. Hirasawa, I.; Mikani, T.; Katayama, A.; Sakuma, T. Strategy to obtain nm size crystals
716
through precipattion in the presence of polyelectrolyte. Chem. Eng. Technol. 2006, 29 (2),
717
212-214.
718
59. Galland, S.; Andersson, R. L.; Salajkov, M.; Strom,V; Olsson, R. T.; Berglund, L. A.
719
Cellulose nanofibers decorated with magnetic nanoparticles – synthesis, structure and use in
720
magnetized high toughness membranes for a prototype loudspeaker. J. Mater. Chem. C 2013, 1
721
(47), 7963-7972.
722 723
60. Adel, A. M. Incorporation of nano-metal particles with paper matrices. Interdiscip. J. Chem. 2016, 1 (2), 36-46.
32 ACS Paragon Plus Environment
Page 32 of 50
Page 33 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Sustainable Chemistry & Engineering
724
61. Boufi, S.; Ferraria, A. M.; Botelho, doRego. A. M.; Battaglini, N.; Herbst, F.; Vilar, M. R.
725
Surface functionalisation of cellulose with noble metals nanoparticles through a selective
726
nucleation. Carbohydr. Polym. 2011, 86 (4), 1586-1594.
727 728
62. Qu, P.; Shancheng, Y.; Meng, H. Controllabe growth of cadmium hydroxide nanostructures by hydrothermal method. Solid State Sciences 2010, 12, 83–87.
729
63. https://tools.thermofisher.com/content/sfs/manuals/mp10024.pdf retrieved 17 August 2017.
730
64. Rorrer, G. L.; Hsien, T. Y. Synthesis of porous-magnetic chitosan beads for removal of
731
cadmium ions from waste water. Ind. Eng. Chem. Res. 1993, 32, 2170-2178.
732
65. Wei, W.; Sok, K.; Myung-He, S.; Bediako, K.; Yeoung-Sang, Y. J. Carboxymethyl cellulose
733
fiber as a fast binding and biodegradable adsorbent of heavy metals. Taiwan. Inst. Chem.
734
Eng. 2015, 57, 104-110.
735 736
66. Mohd, R.; Othman, S.; Rokiah, H.; Anees, A. Removal of cadmium(II) from aqueous solutions by adsorption using meranti wood. Wood Sci. Technol. 2012, 46 (1), 221-241.
737
67. Mohd, R.; Othman, S.; Rokiah, H.; Anees, A. Adsorption of cadmium from aqueous solution
738
onto untreated coffee grounds: equilibrium, kinetics and thermodynamics. J. Hazard. Mater.
739
2010, 186, 124-134.
740
68. Liuchun, Z.; Chaofei, Z.; Zhi, D.; Hui, Z.; Xiaoyun, Y.; Congqiang, L. Preparation of
741
cellulose derived from corn stalk and its application for cadmium ion adsorption from
742
aqueous solution. Carbohydr. Polym. 2012, 90, 1008-1015.
743 744
69. Azouaou, N.; Sadaoui, Z.; Mokaddem, H. Removal of cadmium from aqueous solution by adsorption on vegetable wastes. J. Appl. Sci. 2008, 8, 4638-4643.
33 ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
745
70. Garg, U.; Kaur, M. P.; Jawa, G. K.; Sud, D.; Garg, V. K. Removal of cadmium(II) from
746
aqueous solutions by adsorption on agricultural waste biomass. J. Hazard. Mater. 2008, 154,
747
1149–1157.
748
71. Hossain, A.; Bhattacharyya, S. R.; Aditya, G. Biosorption of cadmium by waste shell dust of
749
fresh water mussel Lamellidens marginalis: Implications for metal bioremediation. ACS
750
Sustainable Chem. Eng. 2015, 3, 1-8.
751
72. Deng, S.; Zhang, G.; Liang, S.; Wang, P. Microwave assisted preparation of thiol-
752
functionalized polyacrylonitrile fiber for the selective and enhanced adsorption of mercury
753
and cadmium from water. ACS Sustainable Chem. Eng. 2017, 5, 6054-6063.
754
73. Liang, J.; Li, X.; Yu, Z.; Zeng, G.; Luo, Y.; Jiang, L.; Yang, Z.; Qian, Y.; Wu, H.
755
Amorphous MnO2 modified biochar derived from aerobically composted swine manure for
756
adsorption of Pb(II) and Cd(II). ACS Sustainable Chem. Eng. 2017, 5, 5049-5058.
757
74. Guo, Z.; Zhang, X.; Kang, Y.; Zhang, J. Biomass derived carbon sorbents for Cd(II) removal:
758
Activation and adsorption mechanism. ACS Sustainable Chem. Eng. 2017, 5, 4103-4109.
759
75. Kula, I.; Uğurlu, M.; Karaoğlu, H.; Celik, A. Adsorption of Cd(II) ions from aqueous
760
solutions using activated carbon prepared from olivestone by ZnCl2 activation. Bioresour.
761
Technol. 2008, 99 (3), 492−501.
762
76. Mohan, D.; Singh, K. P. Single-and multi-component adsorption of cadmium and zinc using
763
activated carbon derived from bagasse agricultural waste. Water Res. 2002, 36(9),
764
2304−2318.
765
77. Kobya, M.; Demirbas, E.; Senturk, E.; Ince, M. Adsorption of heavy metal ions from
766
aqueous solutions by activated carbon prepared from apricot stone. Bioresour. Technol.
767
2005, 96 (13), 1518−1521.
34 ACS Paragon Plus Environment
Page 34 of 50
Page 35 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
768 769 770 771
ACS Sustainable Chemistry & Engineering
78. Wilson, K.; Yang, H.; Seo, C. W.; Marshall, W. E. Select metal adsorption by activated carbon made from peanut shells. Bioresour. Technol. 2006, 97 (18), 2266−2270. 79. Jia, Y.; Thomas, K. Adsorption of cadmium ions on oxygen surface sites in activated carbon. Langmuir 2000, 16 (3), 1114−1122.
772
80. Boudrahem, F.; Soualah, A.; Aissani-Benissad, F. Pb(II) and Cd(II) removal from aqueous
773
solutions using activated carbon developed from coffee residue activated with phosphoric
774
acid and zinc chloride. J. Chem. Eng. Data 2011, 56 (5), 1946−1955.
775
81. Mahmoud, M. E.; Abdou, A. E.; Ahmed, S. B. Conversion of waste styrofoam into
776
engineered adsorbents for efficient removal of cadmium, lead and mercury from water. ACS
777
Sustainable Chem. Eng. 2016, 4 (3), 819−827.
778
82. Tang, J.; Mu, B.; Zheng, M.; Wang, A. One-step calcination of the spent bleaching earth for
779
the efficient removal of heavy metal ions. ACS Sustainable Chem. Eng. 2015, 3 (6),
780
1125−1135.
781 782
83. Jeon, C.; Park, J. Y.; Yoo, Y. J. Characteristics of metal removal using carboxylated alginic acid. Water Res. 2002, 36, 1814-1824.
783
84. Marchetti, V.; Cleament, A.; Gearardin, P.; Loubinoux, B. Synthesis and use of esterified
784
sawdusts bearing carboxyl group for removal of cadmium(II) from water. Wood Sci. Technol.
785
2000, 34, 167-173.
786
85. Lv, K. L.; Du, Y. L.; Wang, C. M. Synthesis of carboxylated chitosan and its adsorption
787
properties for cadmium(II), lead(II) and copper(II) from aqueous solutions. Water Sci.
788
Technol. 2009, 60.2, 467-474.
789 790
86. Blazquez, G.; Hernainz, F.; Calero, M.; Ruiz-Nunez, L. F. Removal of cadmium ions with olive stones: the effect of some parameters. Process Biochem. 2005, 40, 2649-2654.
791 35 ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 36 of 50
792
Table 1. General properties of NOCNF extracted from spinifex using the nitro-oxidation
793
method. Charge
- 68 mV
COO-
Size
content
(L/D) nm
0.86
190±90/
mmol/g
4.0±1.5
PDI
0.35±0.01
794 795
PDI: polydispersity index; CI: crystallinity index; SA: surface area
796 797
36 ACS Paragon Plus Environment
CI
SA
(%)
(m2/g)
53
5.7
Page 37 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Sustainable Chemistry & Engineering
798
Table 2. Calculated ideal adsorption capacity and experimental adsorption capacity of NOCNF
799
for the cadmium(II) removal in the Cd+2 concentration range of 50-5,000 ppm. Final Cd+2
Original Cd+2
Adsorption
Original
Original NOCNF
Ideal
Experimental
conc. by
conc. by
efficiency
quantity
(0.2 wt%)/2mL
adsorption
adsorption
ICPMS
ICPMS
Cd2+(mg)
(g)
capacity
capacity
(ppb)
(ppb)
(mg/g)
Qe (mg/g)
4,300
5,000
0.14
20
0.004
5,000
736
2,075
2,500
0.17
10
0.004
2,500
428
325
1,250
0.74
5
0.004
1,250
233
110
500
0.78
2
0.004
500
99
40
250
0.84
1
0.004
250
53
100
125
0.20
0.5
0.004
125
26
9.5
50
0.81
0.2
0.004
50
10
800 801
Total amount of NOCNF used in 2 mL of 0.2 wt% suspension = 0.004 g
802
Adsorption efficiency = (original Cd2+ conc. - final Cd2+ conc.) / original Cd2+ conc.
803
Ideal adsorption capacity = milligrams of Cd2+in solution / grams of NOCNF in suspension
804
Experimental adsorption capacity = adsorption efficiency x ideal adsorption capacity
805
Qe: experimental adsorption capacity; Ce: original concentration of Cd2+ in ppm
806
37 ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
807
Table 3. The relationship between the values of Ce/Qe versus Ce; the results could be fitted by the
808
Langmuir adsorption model to determine the maximum adsorption capacity (Qm) of NOCNF. 809
Ce (ppm)
Qe (mg/g)
Ce/Qe
810
5,000
736
6.80
811
2,500
428
5.84
812
1,250
233
5.36
813
500
99
5.08
814
250
53
4.76
815
125
26
4.9
816
50
10
5
817
38 ACS Paragon Plus Environment
Page 38 of 50
Page 39 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Sustainable Chemistry & Engineering
818
Table 4. Comparison of the Qm value obtained for NOCNF with those of different adsorbents
819
reported in the literature. Type of adsorbent
Maximum adsorption
Reference
capacity (mg /g) NOCNF
2,550
This study
flower – like magnesium oxide
1,500
51
chitosan beads
518-188
64
epichlorohydrin cross-linked carboxymethyl
150
65
meranti wood
150 – 175
66
untreated coffee grounds
15 – 17
67
corn stalk
3.39
68
maize cob
105
69
jatropha oil cake
86
70
sugarcane bagasse
69
70
waste shell dust of water mussel
18.18
71
thiol functionalized polyacrylonitrile fibers
350.6
72
MnO2-biochar
45.8
73
activated charcoal
8-40
74-80
styrofoam
50-70
81
attapulgite/ carbon nanocomposites
46
82
carboxylated alginic acid
50-100
83
esterified saw dust bearing carboxyl group
198
84
cellulose
39 ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 40 of 50
carboxylated chitosan
720-800
85
carboxylated cellulose nanocrystals
1.9
10
cellulose nanocrystals modified using
345
10
sodium succinate 820 821
40 ACS Paragon Plus Environment
Page 41 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Sustainable Chemistry & Engineering
Figure 1. (i) FTIR spectra and (ii) 13C CPMAS NMR spectra of spinifex fibers and NOCNF.
ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Figure 2. (i) WAXD profiles of (A) spinifex and (B) NOCNF; (ii) TEM image of NOCNF extracted from spinifex using the nitro-oxidation method.
ACS Paragon Plus Environment
Page 42 of 50
Page 43 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Sustainable Chemistry & Engineering
Figure 3. (i) Comparative images of two samples: (left) 5 mL of solution based on 5,000 ppm of cadmium nitrate and distilled water, (right) 5 mL of a NOCNF suspension (0.20 wt%) mixed the cadmium nitrate solution (5,000 ppm) at pH 7, (ii) FTIR spectra of (A) NOCNF and (B) floc obtained from the mixture of cadmium nitrate solution (500 ppm of Cd2+) and NOCNF suspension (0.20 wt%).
ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Figure 4. (i) SEM of the floc obtained from the mixture of NOCNF suspension and 500 ppm of cadmium nitrate solution (inset: EDS spectra); (ii) SEM of the floc obtained from the mixture of NOCNF suspension and 1,000 ppm of cadmium nitrate solution (inset: EDS spectra).
ACS Paragon Plus Environment
Page 44 of 50
Page 45 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Sustainable Chemistry & Engineering
Figure 5. (i) TEM image of the floc containing NOCNF and Cd(OH)2 nanocrystals (black dots); (ii) corresponding WAXD profile (reflection peaks were indexed by the unit cells of cellulose I and Cd(OH)2) of the floc obtained by mixing a 1,250 ppm of Cd2+ solution and NOCNF suspension (0.20 wt%) at pH = 7.
ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Figure 6. Confocal images of (i) NOCNF, stained with the acid blue (using the laser with = 580 nm), (ii) cadmium nitrate deposited with a 1,000 ppm solution, where Cd2+ ions were stained by LeadmiumTM AM dye (using the laser with = 405-490 nm); (iii) the floc obtained by mixing stained NOCNF (with acid blue) and stained Cd2+ ions (with LeadmiumTM AM dye) taken at =580 nm; (iv) the same floc taken at =470 nm (the red circles indicated the aggregates of NOCNF and cadmium hydroxide nanocrystals).
ACS Paragon Plus Environment
Page 46 of 50
Page 47 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Sustainable Chemistry & Engineering
(i)
(ii) Figure 7. (i) Adsorption of Cd2+ ions by the NOCNF suspension at the Cd+2 concentration between 500 and 5,000 ppm, (ii) the fitting of the adsorption data using the Langmuir isotherm model (Qe is the adsorption capacity measured in milligrams of Cd2+ per gram of NOCNF, Ce is the original Cd2+ concentration measured in mg of cadmium(II) per liter of solution).
ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Page 48 of 50
Figure 8. The effect of pH value on the Cd2+ adsorption efficiency of NOCNF at the cadmium concentration of 10,000 ppm.
ACS Paragon Plus Environment
Page 49 of 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ACS Sustainable Chemistry & Engineering
Figure 9. Photographs of (i) freeze dried NOCNF (0.056 g) dispersed in 150 mL of water, (ii) 5 minutes after the addition of 10 mL cadmium nitrate solution (1,500 ppm) in the (i) NOCNF suspension, and (iii) filtration of (ii) through a filter paper (average pore size = 40 µm) using the gravity filtration method.
ACS Paragon Plus Environment
ACS Sustainable Chemistry & Engineering 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Table of Content Graphic
Carboxylated nanofibers (NOCNF) extracted from spinifex using nitro-oxidation approach was efficient in removing cadmium(II) from water via adsorption and mineralization.
1
ACS Paragon Plus Environment
Page 50 of 50