Removal of Trivalent and Hexavalent Chromium by ... - ACS Publications

Hexavalent and trivalent chromium is often present in wastewater from electroplating and metal-finishing plants. Since chromium, along with most of th...
4 downloads 0 Views 99KB Size
Environ. Sci. Technol. 1998, 32, 2693-2698

Removal of Trivalent and Hexavalent Chromium by Seaweed Biosorbent DAVID KRATOCHVIL, PATRICIA PIMENTEL,† AND BOHUMIL VOLESKY* Department of Chemical Engineering, McGill University, 3610 University Street, Montreal, Canada H3A 2B2

Protonated or Ca-form Sargassum seaweed biomass bound up to 40 mg/g of Cr(III) by ion exchange at pH 4. An ion-exchange model assuming that the only species taken up by the biomass was Cr(OH)2+ successfully fitted the experimental biosorption data for Cr(III). The maximum uptake of Cr(VI) by protonated Sargassum biomass at pH 2 was explained by simultaneous anion exchange and Cr(VI) to Cr(III) reduction. At pH 2.0, the removal of Cr(VI) was linked to the depletion of protons in equilibrium batch systems via an anionexchange reaction. The optimum pH for Cr(VI) removal by sorption lies in the region where the two mechanisms overlap, which for Sargassum biomass is in the vicinity of pH 2. The existence of the optimum pH for the removal of Cr(VI) may be explained by taking into account (a) the desorption of Cr(III) from biomass at low pH and (b) the effect of pH on the reduction potential of Cr(VI) in aqueous solutions. Seventy percent of Cr(VI) bound to the seaweed at pH 2 can be desorbed with 0.2 M H2SO4 via reduction to Cr(III).

Introduction Hexavalent and trivalent chromium is often present in wastewater from electroplating and metal-finishing plants. Since chromium, along with most of the heavy metals, is considered toxic, discharge limits for both Cr(III) and Cr(VI) have been instituted by most industrialized countries. The conventional treatment of spent plating and anodizing baths which are rich in chromium consists of four steps, including (1) the reduction of Cr(VI) to Cr(III), (2) the precipitation of Cr(III) as Cr(OH)3 at high pH, (3) the settling of the insoluble metal hydroxide, and finally (4) the disposal of the dewatered sludge. The major shortcomings of the conventional treatment include costly safe disposal of toxic sludge, high cost of chemicals used for Cr(VI) reduction, and incomplete reduction of Cr(VI). Wastewater containing relatively low concentrations of Cr(VI) is usually treated with ion-exchange resins which offer the advantage of the recovery of chromic acid but at a high cost brought about mainly by the high cost of the resins. Recently, in response to these shortcomings, the chromium sequestering capabilities of inexpensive biomasses, including peat moss (1), maize cob, sawdust, beet pulp, sugar cane bagasse (2), pine bark (3), waste fertilizer slurry (4), the * Author to whom correspondence should be addressed. E-mail: [email protected]. † CETEC, Belo Horizonte, MG, Brazil. S0013-936X(97)01073-0 CCC: $15.00 Published on Web 08/13/1998

 1998 American Chemical Society

shrimp chitin (5), the dead cells of bacteria (6), and fungi (7, 8), have been studied. Some of the biomass types have been reported to bind more than 100 mg of Cr/gram of sorbent (2). The sorption of Cr by Sargassum seaweed biomass has never been studied. However, Sargassum is known to be a very good biosorbent for other heavy metals including Cu, Cd, and Zn (9, 10). Although most of the treatment processes removing Cr from wastewater have to ensure successful removal of both Cr(III) and Cr(VI), hitherto, all investigations of biosorption of chromium have studied the removal of only a single chromium form. Moreover, the biomasses which were tested for uptakes of Cr(III) were different from the ones tested for binding with Cr(VI). Consequently, the characteristics of binding of these two forms of chromium have never been compared or related to each other. The objective of this article is to provide a unified approach to the removal of chromium whereby the potential of employing Sargassum biomass at different stages of the conventional wastewater treatment is evaluated, based on sorption data obtained for both trivalent and hexavalent chromium.

Materials and Methods Biosorbent Preparation. Sargassum seaweed biomass was collected beach-dried on the Gulf Coast of Florida in August. H-biomass was prepared in the laboratory by first washing the seaweed with 0.2 M H2SO4 and then rinsing it with distilled water. Ca-biomass was prepared by washing the H-biomass with 0.25 g/L solution of Ca(OH)2. The pH of the spent wash solution was 12. Finally, both the H-biomass and the Cabiomass were dried in the oven overnight at 50 °C. Equilibrium Sorption Experiments. Solutions of Cr(III) and Cr(VI) in distilled water were prepared using CrK(SO4)2 and CrO3, respectively. Approximately 200 mg of dried protonated or Ca-biomass was combined with 50 mL of metal solutions in 200 mL Erlenmeyer flasks. This batch sorption system was gently mixed on a shaker, and left to equilibrate for 6 h. Uptakes of chromium were determined from the difference of metal concentrations in the initial and final solutions. The pH of the solutions before and during the sorption experiments was adjusted with NaOH, H2SO4, and/ or Ca(OH)2. Analysis of Chromium. The total concentration of chromium, i.e., Cr(VI) + Cr(III), in the liquid samples was determined by atomic absorption spectroscopy (PerkinElemer 3100). Hexavalent chromium was analyzed by measuring absorbance of the purple complex of Cr(VI) with 1,5-diphenylcarbohydrazide at 540 nm by UV spectrophotometer (11). The concentration of trivalent chromium was determined as the difference between total chromium and hexavalent chromium concentrations, respectively.

Results and Discussion Removal of Trivalent Chromium. Effect of pH. The effect of pH on the removal of Cr(III) was examined. Figure 1 shows the sorption isotherms obtained for Cr(III) on H-biomass at equilibrium pHs of 4, 2, and 1. As can be seen from this figure, the equilibrium uptakes of Cr(III) at pH 4 were greater than the uptakes at pH 2 throughout the entire range of final concentrations of Cr(III) from 0 to 650 mg/L. The pH had a tendency to drop during the equilibration, hence NaOH was used to adjust the pH. Negligible uptakes of Cr(III) were obtained at pH 1. Similar trends in sorption data have previously been reported for Cu, Cd, and Zn, sorbing onto VOL. 32, NO. 18, 1998 / ENVIRONMENTAL SCIENCE & TECHNOLOGY

9

2693

FIGURE 1. Effect of pH on the sorption of Cr(III) by Sargassum H-biomass. Cr(III) sorption isotherms at (9) pH 4; (O) pH 2; (×) pH 1. algal biomass (12, 13). Moreover, it has been established that heavy metal cations bind to algae by ion exchange whereby weakly and strongly acidic functional groups in the biomass take up cations of heavy metals from solutions in exchange for protons and/or cations of light metals such as Na, Mg, and Ca (14, 15). Therefore, it may be assumed that (1) the pH was dropping during sorption as a results of ion exchange between protons and Cr(III), and (2) low uptakes of Cr(III) by Sargassum at low pH were caused by an increased ability of protons to compete with Cr(III) for the binding sites in the biomass. A decrease in Cr(III) uptake at low pH was also observed when ground bark (3) and fungal biomass (7) biosorption was examined, respectively. However, in these studies the effect of pH was not explained and there was no discussion of the sorption mechanism which led to fitting four different Langmuir isotherms to the latter experimental data, one for each pH value. Alves at al. (3) concluded that ion exchange played an important role in the sorption of Cr(III) by pine bark based on the pH changes observed during equilibration of the bark with metal solutions. However, there was no discussion of the pH changes and no account was made of the pH changes caused by complexation and hydrolysis of Cr(III) in water. Effect of Cr(III) Speciation. It is well-known that Cr3+ cations in water can undergo hydrolysis and/or complexation reactions, the extent of which depend primarily on the total Cr(III) concentration, on the pH, and on the type of anions present in solutions. The simple hydrolysis of Cr3+ can be written as follows:

Cr3+ + H2O S Cr(OH)2+ + H+

(1)

As can be seen, this reaction generates divalent cations Cr(OH)2+ and protons which contribute to the increased acidity of Cr(III) solutions. It is the involvement of protons in reaction 1 that may lead to incorrect interpretations of the pH changes in the system. For example, if Cr3+ is being taken up by the biomass, reaction 1 proceeds to the left, leading to the depletion of protons and hence a rise in pH. In contrast, if Cr(OH)2+ sorbs onto the biomass, reaction 1 naturally proceeds to the right and the solution becomes more acidic. However, the pH of a solution may also change due to the release and/or uptake of protons by the biomass. The value of the equilibrium constant of reaction 1 has been reported by Hunt (16) to be Kh ) 10-3.82 yielding a pKh of 3.82. This means that, at pH 3.8, approximately 50% of the overall 2694

9

ENVIRONMENTAL SCIENCE & TECHNOLOGY / VOL. 32, NO. 18, 1998

FIGURE 2. Ca2+ S Cr(III) cation exchange. Ratio of Ca2+ released and Cr(III) sorbed by Ca-biomass, pH between 3.3 and 3.8. (9) Experimental data; (- -) ratio of Ca/Cr averaged over the datapoints. Cr(III) content of the system will be in the Cr(OH)2+ form. When compared to other trivalent cations, Cr3+ cations appear to be more susceptible to hydrolysis via reaction 1 than Al3+ cations whose pKh is 5.09, but less susceptible than Fe3+ cations which have a pKh value of 2.17. In addition to hydrolysis, Cr3+ can undergo complexation reactions with anions. The constants of complexation reactions have been measured and subsequently included in the thermodynamic databases of software packages such as MINEQL 17, which are used for calculating chemical equilibria in aqueous solutions. Therefore, MINEQL was used to examine the existence of various ionic species of trivalent chromium in solutions of CrKSO4, with CrKSO4 concentrations ranging 2-20 mM and pH 2-4. According to the program, the following species may exist in water under the condition stated above: Cr3+, Cr(OH)2+, CrSO4+, Cr2[(OH)2(SO4)]2+, CrOHSO4, and Cr2(OH)2(SO4)2. Ion Exchange in Cr(III) Biosorption. To be able to model the sorption of Cr(III) by Sargassum biomass, one or several reactions between Cr(III) and the biomass have to be assumed. Thus far, the discussion of the experimental results and of the Cr(III) speciation have revealed that (1) Cr(III) is likely to sorb onto the seaweed by an ion-exchange mechanism and (2) it may be very difficult to determine the stoichiometry of the exchange from pH changes occurring in the system since protons participate in several reactions at the same time. Therefore, the mechanism of Cr(III) removal was investigated using Ca-biomass, in experiments without pH adjustment, by measuring the uptake of Cr(III) and the release of Ca2+, respectively. Figure 2 summarizes the ion exchange observed between Ca2+ and Cr(III). According to this figure, the uptake of 1 mol of Cr(III) by the biomass is accompanied by a release of, on average, 1.1 mol of Ca2+; thus, yielding the Cr(III):Ca exchange ratio of 1.1. The pH of the solution decreased slightly during the sorption experiment yielding the final pH of the metal solutions in the interval of pH from 3.3 to 3.8, depending on the metal concentration. The 1.1:1 stoichiometry implies that over 90% of the Cr(III) sorbed onto the biomass as divalent cations, i.e., probably as Cr(OH)2+. The remaining less than 10% of Cr(III) was probably taken up by the biomass in the form of Cr3+ cations. Consequently, if the uptake of Cr3+ is assumed negligible, the following reaction may be used to describe the sorption of Cr(III) by Sargassum (12):

Cr(OH)2+ + 2B S 2BCr1/2

(2)

where B symbolizes a free binding site in the biomass. In

FIGURE 3. Model and experimental sorption isotherm of Cr(III) on H-biomass at pH 4. (9) Experiment; (-) model (KH ) 4262; KCr(OH)2+ ) 2500 L/mequiv). addition to the metal-binding reaction 2, a mathematical expression for the sorption isotherm of a divalent cation sorbing onto Sargassum in the presence of protons is also available (12, 18, 19). For the specific case of Cr(OH)2+, this expression can be written as

qCr(OH)2+ )

0.5MWCrCt (KCr(OH)2+CfCr)1/2 1 + KHCfH + (KCr(OH)2+CfCr)1/2

(3)

where qCr(OH)2+ stands for the equilibrium uptake of Cr(III), and CfH and CfCr represent the final concentrations of H+ and Cr(III) in the solution, respectively. Equation 3 can be used to predict the sorption of Cr(III) onto Sargassum, provided that (1) the values of the constants KH, Ct, and KCr(OH)2+are known, and (2) most of the Cr(III) is sorbed as Cr(OH)2+. The values of the constants KH ) 4624 and Ct ) 2.3 have previously been determined by Kratochvil (14) for the same Sargassum biomass. The value of the constant KCr(OH)2+ ) 2500 was determined by fitting eq 3 to the experimental data presented in Figure 1. In addition, the program MINEQL was used to calculate the range of pH in which Cr(OH)2+ exists in the solution and the pH at which Cr3+ ions start precipitating. According to this program, no more Cr(OH)2+ cations exist in solutions at pH 5. These facts set the limits for the effective removal of Cr(III) by Sargassum as well as for the applicability of the eq 3 to the pH range of pH 2.5-5. Figure 3 compares the experimental and model sorption isotherms for Cr(III) at pH 4. Removal of Hexavalent Chromium. In the second part of this work, the removal of hexavalent chromium by Sargassum biomass was investigated. Effect of pH. First, the equilibrium uptakes of chromium by Sargassum from solutions containing dissolved hexavalent chromium were measured at pH ) 1, 2, and 4, and the resulting sorption isotherms were plotted in Figure 4. As can be seen from this figure, the uptakes of Cr at pH 2 were higher than the corresponding uptakes at pH 1 and 4 over the entire range of the equilibrium concentration of total chromium in the solution. A similar behavior, whereby lowering of the equilibrium pH from neutral to acidic initially yielded an increase in the Cr uptake but when at pH values below pH 2 the Cr uptake decreased, has been reported by Sharma and Forster for a variety of biomasses including peat moss (1), sawdust, sugar cane bagasse, beet pulp, and maize cob (2). Furthermore, the existence of an optimum pH, at which the removal of Cr was maximized, has also been

FIGURE 4. Effect of pH on the sorption uptake of chromium from solutions originally containing only Cr(VI); uptake of chromium at pH 1, 2, and 4. (×) pH 4; (9) pH 2; (O) pH 1.

TABLE 1. Removal of Cr(VI) by Sargassum Biomass initial conditions

equilibrium conditions (after 6 h)

Ci Ci Cf Cf [Cr(VI)] [Cr(III)] [Cr(VI)] [Cr(VI)] q(Crtot) Cr(VI):Cr(III) (mg/L) (mg/L) pHi (mg/L) (mg/L) pHf (mg/g) (-) 101 200 343 648 1022 blank

0 0 0 0 0 0

2 2 2 2 2 6.5

16 86 233 484 773 0

41 49 7 1 0

2.1 2.2 2.4 2.6 2.6 3.8

9 15 25 38 60 0

0.4 1.8 33.3 484

observed by Huang and Wu (20) who studied the sorption of hexavalent chromium on activated carbon. Although Sharma and Forster have discussed some of the factors underlying the complexity of interactions between Cr(VI) and solid biomaterials (1, 2), a complete explanation of the existence of the optimum pH for removing Cr by biosorption has never been given. Furthermore, the presentation of the biosorption data for Cr(VI) by these authors was rather equivocal due to the fact that under certain conditions hexavalent chromium was found to be reduced to Cr(III). In an attempt to gain an insight into the role of H+ in the binding of Cr(VI) and to investigate whether Sargassum reduces Cr(VI) in the same pH range as other biomasses, a set of experiments was carried out at the initial pH 2 and without pH adjustment. Table 1 summarizes the initial and final compositions of the liquid as well as the uptake of Cr by the biosorbent. As can be seen from Table 1, the uptake of chromium increased with increasing equilibrium pH of the sorption system. This implies that the binding of Cr by Sargassum may be responsible for the depletion of protons in the system. The data in Table 1 indicate that the lower the equilibrium pH of the mixture, the lower the concentration ratio of trivalent to hexavalent chromium in the liquid. This suggests that Cr(VI) reduction to Cr(III) was favored at lower pH values. Similar trends in equilibrium sorption data were observed by Sharma and Forster (1, 2). However, these authors tried to link the percentage removals of Cr(VI) and total chromium, respectively, to the final concentration of the total Cr in the system, which made the interpretation of their experimental data very difficult. The focus of our work was on the character of interactions between hexavalent chromium and the seaweed biomass. Mechanism of Cr(VI) Removal by Sargassum. To explain both the existence of the optimum pH for the removal of Cr by sorption as observed in Figure 4 and the trends in VOL. 32, NO. 18, 1998 / ENVIRONMENTAL SCIENCE & TECHNOLOGY

9

2695

experimental data in Table 1 discussed above, the following combined ion exchange-redox reaction mechanism for the sorption of Cr(VI) by the biomass is proposed:

redox reactions: biomass: C(org) f CO2 and/or C(org) f C (org oxidized) (4) chromium: HCrO4- + 7H+ + 3e f Cr3+ + 4H2O (5) cation exchange: (Cr-B3) + 3H+ S 3(B-H) + Cr3+ (6) anion exchange: B′ + HCrO4- + H+ S B′‚H2CrO4

(7)

It should be mentioned that while all the reactions in the scheme above are written for HCrO4- ions, the mechanism can easily be extended to include the other Cr(VI) species which are likely to be present in the system, such as Cr2O72-, and/or CrO42-. The reaction scheme suggests that HCrO4ions can simultaneously sorb onto biomass by ion exchange according to reaction 7 and oxidize the biomass according to reaction 4. Furthermore, as the scheme above indicates, the ion exchange and the redox reactions may proceed either sequentially and/or in parallel. To elucidate the role of pH in the biosorption of hexavalent chromium, the effect of pH on the equilibria of the individual reactions 5 and 7 is discussed in the following two paragraphs. Reaction 5 describes the biomass as an anion exchanger removing Cr(VI) from aqueous solutions by the “acid adsorption” mechanism which has previously been established as one of the mechanisms of ion exchange on weak anion-exchange resins (21). One type of weakly basic group in the biomass may be phenolic groups of polyphenolic compounds, such are polyphloroglucinols which are known to be present in brown seaweed (22). The most important feature of the acid adsorption mechanism is that, in order for the uptake of chromium to occur, the liquid has to contain enough protons to effectively push the equilibrium of reaction 7 to the right. Consequently, the equilibrium uptake of hexavalent chromium by Sargassum is expected to increase with decreasing pH or decrease with increasing pH. From the thermodynamic point of view, the redox reactions 4 and 5 may proceed in the direction as they are written only if the reduction potential of HCrO4- ions is greater than the reduction potential of the biomass, i.e., when E(CrO42-/Cr3+) > E(B-red,B-ox). While the value of E(B-red,Box) is generally unknown, the value of E(HCrO4-/Cr3+) at 25 °C can be calculated from the Nernst equation which can be written for the reaction 5 as follows:

E(HCrO4-/Cr3+) ) E° + ∆EHCrO-/Cr3+ + ∆EpH ) E°(HCrO4-/Cr3+) +

C(HCrO4-) 0.059 0.059 -7 × log pH 3 3 C(Cr3+) (8)

Assuming isothermal conditions, eq 8 shows that the value of the reduction potential E(HCrO4-/Cr3+) can be obtained as a sum of three terms including E°, ∆EHCrO4-/Cr3+, and ∆EpH which reflect respective contributions of the standard reduction potential E°(HCrO4-/Cr3+), the ratio of hexavalent to trivalent chromium, and the pH. The higher the ratio C(HCrO4)/C(Cr3+) and the lower the pH, the greater the value 2696

9

ENVIRONMENTAL SCIENCE & TECHNOLOGY / VOL. 32, NO. 18, 1998

FIGURE 5. Effects of pH and Cr(VI)/Cr(III) ratio on the reduction potential of chromate ions caculated from eq 8. (O) ∆EpH; (9) ∆EHCrO4-/Cr3+. of the potential E(HCrO4-/ Cr3+), and hence the stronger the ability of HCrO4- to oxidize the biomass. To assess the respective impacts of chromium speciation and pH on the redox behavior of the system, the changes of E(HCrO4-/ Cr3+) caused by variations in pH and in the ratio of C(HCrO4-)/C(Cr3+) were calculated from eq 8 and plotted in Figure 5. As can be seen from this figure, an increase of the ratio C(HCrO4-)/C(Cr3+ ) by 2 orders of magnitude produces a positive ∆EHCrO4-/Cr3+ of +39 mV while the change of the same magnitude in pH yields a negative ∆EpH of -275 mV. This means that pH has a much stronger effect on the reduction potential of chromate than the ratio of hexavalent to trivalent chromium. In fact, an increase of pH causes the value of E(HCrO4-/Cr3+) to drop dramatically, thereby weakening the oxidizing power of HCrO4- ions with respect to the biomass. Consequently, a critical value of pH, designated as pHC, may be defined for any given biomass, so that at pH ) pHC, the reduction potential of HCrO4- ions and the biomass, respectively, are equal, i.e., E(HCrO4-/Cr3+) ) E(B-red,B-ox). It follows from the discussion above that at pH lower than pHC, E(HCrO4-/Cr3+) > E(B-red, B-ox), and hence HCrO4- ions oxidize the biomass, while at pH greater than pHC, E(HCrO4-/Cr3+) < E(B-red, B-ox), and all of the chromium stays in the hexavalent form. Explanation of the Optimum pH Existence. At a relatively high pH, there are not enough protons to shift the equilibrium of the reaction 7 sufficiently to the right. Consequently, only a small uptake of HCrO4- was seen at pH 4 in Figure 4. As the equilibrium pH decreased to pH 2, the uptake of HCrO4by anion exchange increased. However, as soon as the equilibrium pH was lowered below the value of pHC, HCrO4ions started oxidizing the biomass while producing Cr3+ ions. These Cr3+ ions then competed for the binding sites in the biomass with protons via cation exchange reaction (6). Therefore, a further decrease of pH caused not only the value of E(HCrO4-/Cr3+) to increase according to eq 8, thus facilitating the biomass oxidation, but also a fast desorption of Cr3+ from the biomass leading to low uptakes of chromium as seen at pH 1 in Figure 2. Consequently, the uptake of Cr from solutions containing Cr(VI) by biomass is maximized at a value of pH which is low enough for the equilibrium of the anion-exchange reaction 7 to be shifted to the right, but still high enough to be in the vicinity of pHC so that the reduction of HCrO4- to Cr3+ does not dominate the system. On the basis of the data in Table 1, it may be concluded that pHC for Sargassum biomass is approximately equal to 2.5. Further Support of the Proposed Mechanism. To further support the above hypothesis concerning the mechanism of Cr(VI) removal, two experiments were conducted at a relatively high and at an extremely low equilibrium pH value,

TABLE 2. Removal of Cr(VI) by Sargassum Ca-Biomass at pH ) 7, and by Sargassum H-Biomass in 0.2 M H2SO4 initial conditions

Ci [Cr(VI)] (mg/L)

Ci [Cr(III)] (mg/L)

220 400 720 252 407 773

0 0 0 0 0 0

equilibrium conditions (after 6 h)

pHi

Cf [Cr(VI)] (mg/L)

Cf [Cr(VI)] (mg/L)

7.2 7.2 7.2 0.2 M H2SO4 0.2 M H2SO4 0.2 M H2SO4

210 380 680 0.134 0.828 87

0 0 0 250 385 680

respectively. According to the proposed reaction scheme, at high pH, HCrO4- should not be taken up by the biomass at all due to the low concentration of protons in the system. In contrast, at low pH, ∆EpH = 0 and the value of E(HCrO4-/ Cr3+) is high. Thus, the redox reactions 4 and 5 are expected to dominate the equilibrium behavior of the system. The first experiment was performed with Sargassum biomass in the Ca-form at pH 7. The pH of the initial solution was adjusted prior to the sorption experiment by adding Ca(OH)2 to the solution of H2CrO4. Table 2 reveals that the uptake of chromium at pH 7 was indeed negligible, complemented by no significant change in the pH of the system. Furthermore, no Cr(III) was detected in the liquid in equilibrium. The second experiment was carried out in 0.2 M H2SO4, and as can be seen from Table 2, almost all HCrO4ions present in the initial solution were reduced to Cr3+ over the course of 6 h, and practically no Cr(VI) was left unreacted in the systems after 1 day. The results obtained under the acidic conditions have two major implications for the potential use of biosorbents: (1) it is possible to desorb most of the chromium from biomass by mineral acids via reduction to Cr(III), and (2) biosorbents may be considered as a low-cost alternative to oxidizing agents such as SO2 and Na2S2O5 used for the reduction of Cr(VI) to Cr(III) in the first step of the conventional treatment process. The latter suggestion is further favored by the fact that the spent plating baths are very acidic as they contain residual chromic acid. A visual inspection of the biomass after the 24 h exposure to acid in the presence of Cr(VI) revealed that the seaweed lost, to a varying degree, its originally brown coloring. In fact, a gradient of brown color was observed in the samples, ranging from completely discolored and transparent biomass which had been exposed to the highest concentration of Cr(VI), to almost unchanged color of the biomass from the blank sample which contained only H2SO4 and no Cr(VI). Therefore, it may be concluded that the loss of color was due to the oxidation and/or extraction of pigments by Cr(VI). The main pigments in brown algae are chlorophyll and fucoxanthin; the latter being an accessory pigment which lends the brown color to the seaweed (23). On the basis of the present results, the following conclusions can be drawn. At pH >2.5, Cr(III) sorbs onto Sargassum biomass by ion exchange in the form of Cr(OH)2+ divalent cation. The uptake of Cr(III) by the seaweed can be modeled using Schiewer’s ion-exchange model. The uptake of Cr(III) at pH