Single-Crystal MAPbI3 Perovskite Solar Cells Exceeding 21% Power

Subscriber access provided by Université de Strasbourg - Service Commun de la Documentation

Energy Express

Single-Crystal MAPbI3 Perovskite Solar Cells Exceeding 21% Power Conversion Efficiency Zhaolai Chen, Bekir Turedi, Abdullah Alsalloum, Chen Yang, Xiaopeng Zheng, Issam Gereige, Ahmed AlSaggaf, Omar F. Mohammed, and Osman M. Bakr ACS Energy Lett., Just Accepted Manuscript • Publication Date (Web): 07 May 2019 Downloaded from http://pubs.acs.org on May 7, 2019

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Energy Letters

Single-Crystal MAPbI3 Perovskite Solar Cells Exceeding 21% Power Conversion Efficiency Zhaolai Chen,†,∥ Bekir Turedi ,†,∥ Abdullah Y. Alsalloum,†,∥ Chen Yang,† Xiaopeng Zheng,† Issam Gereige,§ Ahmed AlSaggaf ,§ Omar F. Mohammed, *,† and Osman M. Bakr*,† †Division of Physical Sciences and Engineering, King Abdullah University of Science and Technology, Thuwal 23955-6900, Kingdom of Saudi Arabia §Saudi Aramco Research & Development Center, Dhahran 31311, Kingdom of Saudi Arabia Corresponding Authors: *E-mail: [email protected] ; *E-mail: [email protected] Author Contributions: ∥ Zhaolai Chen, Bekir Turedi, and Abdullah Y. Alsalloum contributed equally to this work.

ABSTRACT: Twenty-microns-thick single-crystal methylammonium lead triiodide (MAPbI3) perovskite (as an absorber layer) grown on the charge-selective contact using a solution spacelimited inverse-temperature crystal growth method yields solar cells with power-conversion efficiencies reaching 21.09% and fill factors of up to 84.3%. These devices set a new record for perovskite single-crystal solar cells, and open an avenue for achieving high fill factors in perovskite solar cells. TOC GRAPHICS

1 ACS Paragon Plus Environment

ACS Energy Letters 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 2 of 6

In the past few years alone, hybrid metal halide perovskite materials have revolutionized the field of low-temperature-processed solar cells, providing devices with power conversion efficiencies (PCEs) that compete with the most established decades-old commercial photovoltaic technologies. To-date, studies on perovskite solar cells (PSCs) have principally been on perovskite polycrystalline film PSCs (Pc-PSCs), The record efficiency for Pc-PSCs– currently at 24.2% PCE1 – is still far from their theoretical Shockley-Queisser limit (SQL), which is ~30.5% PCE for a single-junction cell based on methylammonium lead triiodide (MAPbI3).2 To approach the SQL, it is essential to improve the device’s fill factor (FF) (FF 90% in the SQL for MAPbI3 PSCs)2, which contributes to the overall PCE. The FF is perhaps the most challenging figure of merit to improve for Pc-PSCs because losses in FF are mainly governed by the ideality factor that is related to non-radiative bulk and interface carrier recombination.3-5 Despite marked efforts in improving the FF, polycrystalline thin films have significant parasitic non-radiative carrier recombination due to their inherent grain size and surface defects.6-7 In theory, single-crystal perovskites, with their orders of magnitude lower defect density and higher carrier diffusion lengths compared to their polycrystalline counterparts,8-11 offer a chance for PSC technology to overcome the limitation of polycrystalline thin films and get as close as practical to the SQL.12 Unfortunately, due to the challenges with their thickness control and typically device-incompatible solution-growth conditions, only a handful of groups have led the charge in the development of single-crystal-based PSCs (SC-PSCs). SC-PSCs reached their highest (PCE of 17.8% with FF of 78.6%) in a 2017 report by Huang and co-workers.13 Here, we realize highly efficient SC-PSCs with PCEs reaching 21.09% and FFs of up to 84.3% (under 1-sun illumination AM 1.5G). These devices, based on a ~20 micrometers-thick MAPbI3 single-crystal absorber layer in an inverted p-i-n architecture, set a new record for SC-PSC PCE 2 ACS Paragon Plus Environment

Page 3 of 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Energy Letters

and a new benchmark for potential FFs that PSCs should aim for, which Pc-PSCs have struggled to achieve. The crystals were grown using a simple solution space-limited inverse-temperature crystal growth method (see Supporting Information).13-14 The crystal structure, and optical absorption edge of these crystals are that of typical MAPbI3 single-crystals (see Figure S1 and Figure S2). A scanning electron microscopy (SEM) cross-sectional image of the MAPbI3 SC-PSC (Figure 1a) shows that the active area is pinhole- and grain boundary-free (see also top-view SEM image of the crystal, Figure S3). The smooth surface allows for the full coverage of the charge transport layers,

preventing

direct

crystal-to-metal-electrode

contact.

The

device

follows

an

ITO/Poly(triarylamine) (PTAA)/MAPbI3 single-crystal/C60/Bathocuproine (BCP)/Copper (Cu) architecture with a corresponding energy band diagram illustrated in Figure 1b. The crystal thickness in devices is typically around 20 µm (see distribution in Figure S4). Figure 1c shows the current-voltage characteristics of our best performing cell. The reverse-scan short-circuit current density (JSC), open-circuit voltage (VOC), and FF are 23.46 mA·cm-2, 1.076 V, and 83.5%, respectively, yielding a PCE of 21.09% with negligible hysteresis. The corresponding external quantum efficiency (EQE) and integrated JSC are shown in Figure 1d. To exclude the effect of any potential error in aperture area determination, the JSC of the champion device was verified and corrected from the integrated current calculated from the EQE. The calculated JSC from the EQE measurement was only 1.2% lower than that obtained by an I-V scan for the device which is within the expected error of solar cell J-V measurements. The steady-state maximum power output (SPO) of the champion cell (Figure 1e) shows that the PCE reaches over 21% during the first 10 seconds of measurement and then stabilizes at ~20.7% for over 120 seconds, consistent



Page 4 of 6

with the J-V measurement (Figure 1c). A statistical summary of the device characteristics (Figure 1f) attests to the reproducibility of the fabricated cells and their outstanding performance.

Figure 1. Characterization of SC-PSCs (a) Cross-sectional SEM image of a MAPbI3 SC-PSCs. Note that the few nanometers-thick transporting layers at the crystal’s two interfaces are not visible at such magnification. (b) Energy-level diagram for SC-PSCs. (c) J-V curves of the champion cell in forward- (orange) and reverse-scan (blue) modes and the corresponding photovoltaic parameters under 1-sun illumination. (d) EQE spectra with the integrated JSC of the champion cell. (e) Steadystate photocurrent- and PCE-output at maximum power point with 0.93V bias for the champion cell. (f) A statistical summary, based on 12 devices, of the photovoltaic parameters of SC-PSCs. It is useful to emphasize the experimental precautions, during fabrication and testing, required to achieve the dramatic increase in device performance. First, any spin-coating post-treatment that includes a solvent that might dissolve the charge transporting layer beneath the active layer was avoided to ensure proper attachment of the single-crystal. Second, fabrication, storage, and testing of the devices were conducted in a nitrogen-filled environment to prevent interface hydration that might lead to poor contacts. We observed that efficient SC-PSCs can drastically decrease in performance when measured under ambient conditions (22 oC, 50-55 RH); in particular, the JSC 4 ACS Paragon Plus Environment

Page 5 of 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Energy Letters

markedly decreases while the VOC and FF are largely unaffected (see Figure S5 and Figure S6). Note that when the devices kept under dry air the performance does not change significantly (see Figure S7). Interestingly, the devices fully recovered after storage in N2 for ~48 hours, suggesting that the decrease is unrelated to perovskite degradation, but likely a result of hydration of the single-crystal’s surface, leading to poor contacts with the transporting layers.12, 15 Our devices exhibit ultrahigh FFs (FFaverage=82.6% and FFmax=84.3%; Figure 1f). Our best fabricated, analogous architecture Pc-PSC and SC-PSC have similar VOC; yet despite the higher JSC of the Pc-PSC, the PCE of the SC-PSC ends up being on top due to its superior FF (see Figure S8). We confirmed that the higher FF is uncorrelated to the mask area: even when the mask area is small, the Pc-PSC FF barely reaches 80%, which is still below that of SC-PSCs (Figure S9). In summary, we fabricated MAPbI3 SC-PSCs with PCEs reaching 21.09%, which sets a new efficiency benchmark for SC-PSCs. While there is still room for larger area SC-PSCs16 and substantial interfacial optimization, the high PCE and FF highlight the promise of single-crystals for advancing perovskite device technology, which could be a parallel development path to the one taken by their polycrystalline counterparts.

ASSOCIATED CONTENT Experimental details of device fabrication and characterization; top-view SEM, XRD patterns; absorbance spectrum; and photovoltaic parameters as well as J-V curve comparison of measurements in ambient and nitrogen environments, TOC abbreviations. AUTHOR INFORMATION



Page 6 of 6

The manuscript was written through contributions of all authors. All authors have approved the final version of the manuscript ACKNOWLEDGMENT The authors acknowledge the funding support from King Abdullah University of Science and Technology (KAUST). REFERENCES 1. NREL Best Research-Cell Efficiencies. https://www.nrel.gov/pv/assets/pdfs/best-reserchcell-efficiencies.20190411.pdf. 2019. 2. Pazos-Outón, L; et al. Fundamental Efficiency Limit of Lead Iodide Perovskite Solar Cells. J. Phys. Chem. Lett. 2018, 9, 1703-1711. 3. Chen, J.; et al. Causes and Solutions of Recombination in Perovskite Solar Cells. Adv. Mater. 2018, 1803019. 4. Stolterfoht, M.; et al. Approaching the Fill Factor Shockley–Queisser Limit in Stable, Dopant-Free Triple Cation Perovskite Solar Cells. Energy Environ. Sci. 2017, 10 (6), 1530-1539. 5. Wu, N; et al. Identifying the Cause of Voltage and Fill Factor Losses in Perovskite Solar Cells by Using Luminescence Measurements. Energy Technol. 2017, 5, 1827-1835. 6. Stranks, S. D. Nonradiative Losses in Metal Halide Perovskites. ACS Energy Lett. 2017, 2, 1515-1525. 7. Sherkar, T. S.; et al. Recombination in Perovskite Solar Cells: Significance of Grain Boundaries, Interface Traps, and Defect Ions. ACS Energy Lett. 2017, 2, 1214-1222. 8. Shi, D.; et al. Low trap-state density and long carrier diffusion in organolead trihalide perovskite single crystals. Science 2015, 347, 519-522. 9. Zhumekenov, A. A.; et al. Formamidinium Lead Halide Perovskite Crystals with Unprecedented Long Carrier Dynamics and Diffusion Length. ACS Energy Lett. 2016, 1, 32-37. 10. Dong, Q.; et al. Electron-hole diffusion lengths > 175 μm in solution-grown CH3NH3PbI3 single crystals. Science 2015, 347, 967-970. 11. Alarousu, E.; et al. Ultralong Radiative States in Hybrid Perovskite Crystals: Compositions for Submillimeter Diffusion Lengths. J. Phys. Chem. Lett. 2017, 8, 4386-4390. 12. Wang, K.; et al. Mono-crystalline Perovskite Photovoltaics toward Ultrahigh Efficiency? Joule 2018, 3, 311-316. 13. Chen, Z.; et al. Thin Single Crystal Perovskite Solar Cells to Harvest Below-Bandgap Light Absorption. Nat. Commun. 2017, 8, 1890. 14. Liu, Y.; et al. Thinness‐ and Shape‐Controlled Growth for Ultrathin Single‐Crystalline Perovskite Wafers for Mass Production of Superior Photoelectronic Devices. Adv. Mater. 2016, 28, 9204−9209. 15. Leguy, A. M.; et al. Reversible Hydration of CH3NH3PbI3 in Films, Single Crystals, and Solar Cells. Chem. Mater. 2015, 27, 3397-3407. 16. Liu, Y.; et al. Two-Inch-Sized Perovskite CH3NH3PbX3 (X = Cl, Br, I) Crystals: Growth and Characterization. Adv. Mater. 2015, 27, 5176-5183.


Single-Crystal MAPbI3 Perovskite Solar Cells Exceeding 21% Power

Recommend Documents