Effect of Surfactant on Asphaltene Deposition on Stainless Steel and

10 hours ago - In this work, we study the effects of Dodecylbenzenesulfonic acid (DBSA) as a surfactant on asphaltene deposition on the stainless stee...
0 downloads 12 Views 825KB Size
Subscriber access provided by Service des bibliothèques | Université de Sherbrooke

Process Engineering

Effect of Surfactant on Asphaltene Deposition on Stainless Steel and Glass Surfaces Abdulaziz Al Sultan, Mohsen Zirrahi, Hassan Hassanzadeh, and Jalal Abedi Energy Fuels, Just Accepted Manuscript • DOI: 10.1021/acs.energyfuels.8b00215 • Publication Date (Web): 25 Mar 2018 Downloaded from http://pubs.acs.org on March 25, 2018

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

1

Effect of Surfactant on Asphaltene Deposition on Stainless Steel and Glass Surfaces

2

Abdulaziz Al Sultan1, Mohsen Zirrahi2, Hassan Hassanzadeh2*, Jalal Abedi2

3

1

Saudi Aramco, Dhahran, Saudi Arabia

4

2

Department of Chemical & Petroleum Engineering, Schulich School of Engineering, University

5

of Calgary, Calgary, AB, Canada T2N 1N4

6

Abstract

7

Surfactant dispersants have been introduced as a proper candidate to mitigate the problems

8

caused by asphaltene precipitation such as clogging wells, flowlines, and surface facilities in oil

9

industry. In this work, we study the effects of Dodecylbenzenesulfonic acid (DBSA) as a

10

surfactant on asphaltene deposition on the stainless steel and glass surfaces. Experiments were

11

conducted to measure the asphaltene precipitation in bulk system, asphaltene deposition on the

12

stainless steel and glass surfaces. Results revealed that the surfactant delays the asphaltene onset

13

in the bulk system. However, asphaltene deposition on the stainless steel surface was increased at

14

all measured concentrations of the surfactant while the deposition rate on glass surface decreased

15

by increasing the surfactant concentration. Affinity of the surfactant molecules to the stainless

16

steel surface was verified in asphaltene deposition and removal tests. The results revealed that

17

the DBSA surfactant is able to remove the deposited asphaltene on glass surfaces at high

18

concentrations. This study reveals the importance of surface properties when the surfactant is

19

used as asphaltene dispersant.

20

Keywords: Asphaltene dispersant; onset; surfactant; Dodecylbenzenesulfonic acid (DBSA)

*

Corresponding Author, E-mail: [email protected]

1 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

1

Page 2 of 25

1. Introduction

2

Asphaltene deposition is known to cause clogging of oil wells, flowlines, and surface facilities.

3

Asphaltene deposition costs operators millions of dollars due to issues such as maintenance,

4

replacement or loss of production.1 Finding an effective way to control asphaltene dispersion in

5

petroleum fluid is still a demanding area of research. The past literature on asphaltene mitigation

6

was mainly focused on either prevention or delay of asphaltene precipitation/aggregation.2-5

7

Prevention and delay of asphaltene can be achieved through injection of aromatic solvents,

8

taking benefit from natural inhibitor in crude oil or finally by using dispersants/inhibitors. The

9

latter is the most efficient way to delay or prevent asphaltene problems economically and

10

environmentally, which can lead to stabilizing asphaltene and preventing precipitation or

11

deposition.2 An increasing number of studies are being published related to surfactant

12

dispersants, but until now, these studies are mostly far from practical use and still under the

13

laboratory studies.3-5

14

As an iconic reference in asphaltene dispersion area, Chang and Fogler 5 studied the effect

15

chemical structure of several amphiphiles on stabilization of asphaltene flocs. Asphaltene

16

powder was analyzed for its properties to be used for the onset detection experiments. The

17

adsorption of some amphiphile head group was studied using Fourier Transform Infrared (FTIR)

18

spectrophotometer. Four different amphiphile head groups were compared with respect to the

19

stabilized asphaltene weight and asphaltene adsorption with amphiphiles. Sulfonic acid group

20

(DBSA) showed a desirable result as an effective asphaltene stabilizer. Then, the effect of tail

21

length of amphiphile was studied; concluding that longer tail accounted to better asphaltene

22

stability at the expense of losing some affinity to asphaltene. Afterward, the effect of different

2 ACS Paragon Plus Environment

Page 3 of 25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

1

amphiphile side groups was studied by adding a polar group (i.e. hydroxyl group) to amphiphile.

2

The results showed increase of asphaltene stability. However, the addition of side group has

3

some negative side effect on asphaltene dispersion in solution when it joins the amphiphile at the

4

tail. Lastly, n-alkane solvent type was varied to investigate asphaltene stability. Chang and

5

Fogler 5 concluded that having more volatile solvent lowered asphaltene stability for weak

6

amphiphiles. However, no effect was observed when using strong amphiphiles like DBSA.

7

Wang 6 studied ability of different ionic and non-ionic liquids and their structural differences on

8

asphaltene dispersion. Impendance analysis method was used and confirmed the results of

9

refractometry method. Then, high-resolution transmission electron microscope was utilized to

10

study the structure of asphaltene dispersion and also to confirm the results of the previous

11

methods. The author concluded that ionic surfactant 4-Dodecylbenzensulfonic Acid (DBSA) is

12

the most effective dispersant among those studied followed by the non-ionic liquid 4-

13

Octylphenol (OP).

14

Aslan and Firoozabadi 7 studied the effect of brine and deionised (DI) water on asphaltene

15

deposition using pipe-flow setup. Asphaltene deposition was simulated using the pipe-flow setup

16

where water, oil, and heptane from separate lines were mixed in one junction with a specified

17

concentration. The mixture was then sent through a metal pipe while a pressure transducer was

18

used to measure the pressure difference in the system. Pressure versus the injected volume was

19

used for analysis. They concluded that addition of water to the system noticeably delayed the

20

asphaltene deposition.

21

Subramanian and Firoozabadi 8 went further to study the effect of two different ionic surfactants

22

(ionic “DBSA” and non-ionic “BA”) on asphaltene precipitation and deposition introducing 3 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

1

water and brine to the system. Sedimentation tests were carried out to study the effect of mixing

2

of different water/brines with multiple surfactant concentrations on asphaltene precipitation on

3

Falcon tubes. Although a previous study7 concluded that the presence of water or brine delays

4

asphaltene deposition, study of Subramanian and Firoozabadi 9 showed that BA surfactant was

5

not affected by water or brine addition because water would make the solution more polar by

6

inducing negative charge on the surface of the asphaltene aggregate. On the other hand, DBSA

7

showed poor dispersion in the presence of water or brine and associates with the asphaltene,

8

which weakens the electrostatic interaction between DBSA and asphaltene, resulting in more

9

unstable asphaltene and inefficient dispersion.

Page 4 of 25

10

Loureiro et al. 10 examined the influence of two asphaltene stabilizers or inhibitors (DDBSA and

11

CAAS) using two different destabilizing conditions, one with n-heptane and the other one with

12

CO2. Different concentrations of inhibitor were added to study the change in the onset point of

13

precipitation. The results showed that the inhibitors were system-selective, meaning that each

14

condition (CO2 or n-heptane) responded differently. They delayed asphaltene precipitation in

15

systems containing n-heptane while no significant effect was observed for CO2 containing

16

systems.

17

Several investigations have been conducted to study the effect of surfactants on decrease and/or

18

delay of the asphaltene precipitation and deposition.3-10 These studies suggested injection of the

19

surfactants into streams susceptible to the asphaltene precipitation and deposition. However,

20

there is a lack of information on the effect of surfactant on deposition of asphaltene particles on

21

surfaces such as stainless steel and glass. In this work, we study the effect of dodecyl benzene

22

sulfonic acid (DBSA) as an ionic surfactant on asphaltene deposition on stainless steel and glass

4 ACS Paragon Plus Environment

Page 5 of 25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

1

surfaces. Stainless steel can be a representative of pipeline surface while glass beads can be

2

representative of porous media. Moreover, capability of surfactant to dissolve the deposited

3

asphaltene on a surface is evaluated. The rest of this paper is organized as follows: First, we

4

present the experimental details consisting of material, apparatus and procedure. Then,

5

experimental results are presented followed by conclusions.

6

2. Experimental Details

7

Chemicals and Materials

8

The experiments were conducted using Athabasca bitumen to study the asphaltene deposition.

9

Bitumen properties are listed in Table 1.

10

Table 1. Bitumen source and properties.11, 12 SARA Fractions (wt.%) Saturates 12.26

Aromatics

Resins

Asphaltene

40.08

36.53

11.13

Density (g/cc)

API gravity

1.004

10.0

11

12

Ionic surfactant 4-Dodecylbenzenesulfonic Acid (DBSA) was purchased from Sigma Aldrich

13

with purity higher than 95%. The chemical structure of the DBSA is shown in Figure 1.

MW: 326.5 g/mol Density: 1.0 g/cm3 (at 25°C) Purity: ≥95% 14

Figure 1: 4-dodecylbenzene-1-sulfonic acid (DBSA) chemical structure and properties.

5 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 6 of 25

1

N-heptane and toluene were purchased from BDH VWR ANALYTICAL, while Chloroform was

2

provided by Anachemia. Two types of beads were used: 1) stainless steel beads with 3.95 mm

3

diameter, 2) Borosilicate glass beads with 4 mm diameter from Chemglass Inc. The microscope

4

slides were purchased from VWR VistaVision (3”×4”×1.2mm) with glass cover for microscope

5

slides purchased from Canlab – Baxter (24 mm × 25 mm).

6

Experimental Procedure

7

In this work, we studied the effect of DBSA on asphaltene precipitation in a system of toluene-

8

asphaltene mixture and also deposition of asphaltene on stainless steel and glass surfaces. To

9

study the effect of surfactant on asphaltene precipitation, we measured the amount of precipitated

10

asphaltene in different concentrations of precipitant and surfactant.

11

Asphaltene fractional yield tests: Asphaltene solubility test or fractional yield test was

12

conducted to generate solubility curves, which results the percentage of the precipitated

13

asphaltene versus volume fraction of n-heptane in toluene-heptane mixture. These experiments

14

were conducted in the presence and absence of surfactant. The procedure reported by Sadeghi 13

15

was adopted and slightly modified to fit our purpose. Asphaltene was precipitated using n-

16

heptane from Athabasca bitumen as described in Azinfar et al.14 . A 300 mg of solid-free

17

asphaltene was added to a 25 ml vial. Toluene was added to the asphaltene then put in ultrasonic

18

bath for 20 min till all asphaltene was dissolved. A predetermined amount of toluene was added

19

to the vial to reach the asphaltene concentration of 20 kg/m3 in the solution. Then, n-heptane was

20

added to the mixture to obtain the desired heptane volume percents in toluene (60, 70, 80, and 90

21

vol.%). For the samples containing the surfactant (DBSA), first, a certain amount of surfactant

22

was added to n-heptane and then sonicated for 5 min. Next, the surfactant-heptane mixture was 6 ACS Paragon Plus Environment

Page 7 of 25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

1

added to the mixture of the dissolved asphaltene in toluene to achieve the desired

2

heptane/toluene volume percent. The concentration of the surfactant (ppm) in the mixture was

3

calculated using:

4

ppm =

msur ×106 mtoluene + mC 7 + msur

(1)

5

where msur, mC7, and mtoluene are mass of surfactant, heptane, and toluene, respectively.

6

The mixture was then put in ultrasonic bath for 45 min then left to settle for 1 hr. Each vial was

7

then centrifuged at 4000 rpm for 5 minutes to separate the precipitated asphaltene. Supernatant

8

was then decanted and the vial is placed in vacuum oven at 70 °C for 24 hr then each vial was

9

weighted to determine the asphaltene yield. The same experiments were also conducted in the

10

absence of surfactant and the asphaltene yields at different n-heptane concentrations were

11

measured.

12

Asphalting deposition experiments: The asphaltene deposition experiments were conducted

13

using Athabasca bitumen. We prepared and tested the n-heptane/bitumen mixtures based on the

14

mass fraction basis to avoid errors due to volume change during the mixing of n-heptane and

15

bitumen. First, we prepared a solution of 40 wt.% n-heptane in bitumen. The sample was then

16

sonicated for 90 min and left for 72 hr. This mixture was used to prepare the samples with higher

17

n-heptane concentration. This mixture was checked under microscope to detect possible

18

asphaltene aggregates. No asphaltene precipitation was detected for the mixture of 40 wt% of n-

19

heptane in bitumen. To prepare the samples with higher concentrations of n-heptane, small

20

amount (20-30 g) of the prepared n-heptane-bitumen mixture (40 wt.%) was put into a 250 ml

21

beaker. Afterward, while mixing, a predetermined weight of n-heptane was added to the mixture 7 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 8 of 25

1

to achieve the desired n-heptane concentration. The sample was stirred for 2-10 min. Then, a

2

microscope image was taken before being placed into the deposition apparatus to study the

3

asphaltene aggregate.

4

To prepare the mixture containing the surfactant, the concentration (ppm) of the surfactant in

5

solution was calculated by:

6

ppm =

msur × 106 mbit + mC 7 + msur

(2)

7

where msur, mC7, and mbit are mass of surfactant, n-heptane, and bitumen, respectively.

8

To prepare a sample with certain amount (ppm) of surfactant, we made a pre-determined mixture

9

of surfactant and n-heptane. Then, the mixture was added slowly to the solution of 40 wt.% of n-

10

heptane in bitumen while stirring to reach the desired n-heptane and surfactant concentrations in

11

the solution. After, the solution was stirred for 2-10 min, several drops were studied under the

12

microscope to study the asphaltene aggregate and the rest of the mixture was put into the

13

apparatus to conduct the asphaltene deposition experiments. It is worth to mention that the time

14

for asphaltene destabilization and aggregation for the mixtures with higher than 63 wt.% of n-

15

heptane in bitumen was less than the preparation and settling time (~ 1 hr).

16

The apparatus for asphaltene deposition experiments was designed similar to the one used by

17

Fávero et al.15. The setup shown in Figure 2 consists of a pump (EYELA – CERAMIC PUMP

18

VSP-2200) that injects mixture sample to a glass column (15.3 cm length and 10 mm inner

19

diameter). The glass column was filled with stainless steel (SS) beads (3.95 mm of diameter) or

20

glass beads (4mm of diameter). The total bed length in both SS and glass bead experiments was

21

13.5 cm with a total of 152 beads for the SS bed, and 132 beads for the glass beads. The packed 8 ACS Paragon Plus Environment

Page 9 of 25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

1

bed column effluent was then returned to the mixture sample to form a closed loop. The sample

2

was kept stirred during the entire period of the experiments.

3

When a prepared sample was placed into the apparatus, it was pumped at 0.6 ml/min for a 24-

4

hour period. Then, the sample was drained slowly at a rate of 0.1 ml/min to prevent removal of

5

any deposits from the packed bed. After draining the packed bed column, it was then rinsed with

6

chloroform and the mixture was collected in a vial. The vial was put in a vacuum oven at 75 °C

7

for 24 hr till all chloroform was evaporated. Following the Fávero et al.15 , the retained material

8

in the packed bed column consists of the deposited material and the trapped fluid. The trapped

9

fluid was determined by performing the deposition experiments with run-time of 1 min. This

10

time is assumed small enough for any depositions to occur.15 In these experiments, after

11

circulation of the heptane-bitumen mixture for 1 minute, the amount of the trapped fluid in the

12

packed bed was measured, which is the liquid trapped between the beads.

13 14

Figure 2: Asphaltene deposition apparatus used in experiments.

15

We also utilized the microscope (AmScope Microscope) to check the size of the aggregates

16

before and after putting the sample in the apparatus. Self-association of asphaltene along with

9 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 10 of 25

1

aggregate shape and size are examined using the microscope. Each sample was tested twice.

2

First, the sample was tested 5 min after preparation and the second test was conducted after 24 hr

3

of the sample being stirred and circulated in the deposition apparatus. All microscope images

4

scale was kept the same for comparison purposes. Table 2 shows the range of n-heptane and

5

surfactant in the conducted experiments in this work.

6

Table 2. Range of n-heptane and DBSA concentration in the asphaltene yield and deposition

7

tests. Surfactant concentration

n-heptane concentration

Asphaltene yield experiments

0 to 25,000 ppm

60 to 90 vol. %

Asphaltene deposition experiments

0 to 50,000 ppm

40 to 70 wt.%

8

9

3. Results and Discussion

10

Effect of DBSA Surfactant on Asphaltene Yield

11

Yield and solubility curves have been widely studied in the literature. 12, 14 The fractional yield is

12

defined as ratio of the precipitated asphaltene to the initial mass of asphaltene in the mixture.

13

Effect of DBSA on asphaltene precipitation was studied in bulk system using asphaltene yield

14

test. To get insight into DBSA and asphaltene interaction in the absence of other factors like

15

surface adsorption and other impurities/components in bitumen, solid-free asphaltene from the

16

Athabasca bitumen was used to study the asphaltene solubility and to determine how the DBSA

17

alters the yield.

18

In this study, four n-heptane volumetric fractions (0.6, 0.7, 0.8, and 0.9) in toluene/asphaltene

19

mixtures were studied to track the changes after adding DBSA to the mixture. These volumetric 10 ACS Paragon Plus Environment

Page 11 of 25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

1

fractions of n-heptane allow to focus on the region with asphaltene precipitation higher than the

2

onset point. The results of asphaltene yield in different n-heptane and DBSA concentrations are

3

shown in Figure 3. It can be found that higher n-heptane concentration results in higher

4

precipitated asphaltene. Also, increasing DBSA concentration decreases the asphaltene yield.

5

However, n-heptane volume fractions of 0.8 and 0.9 show a slight increase in the fractional yield

6

by addition of DBSA at low DBSA concentrations. The measured fractional yield greater than

7

100 at 90 vol.% n-heptane and 5,000 ppm of DBSA can be attributed to precipitation of DBSA

8

with asphaltene. This shows that the added surfactant sticks to asphaltene molecules. As the

9

surfactant concentration is increased asphaltene precipitation was not observed. For instance, at

10

15,000 ppm of DBSA asphaltene precipitation was not observed in the mixtures with 0.6, 0.7 and

11

0.8 n-heptane volumetric fractions. At 0.9 volumetric fraction of n-heptane and 15,000 ppm

12

concentration of surfactant results in a fractional yield of 0.56. These observations suggest that

13

surfactant delays the onset and also decreases the asphaltene yield. All curves in this figure were

14

measured at settling time of 1 hr.

11 ACS Paragon Plus Environment

Energy & Fuels

140

120

Fractional Yeild (%)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 12 of 25

60 vol% 70 vol% 80 vol% 90 vol%

100

80

60

40

20

0

0

1

5000

10000

15000

20000

25000

30000

Surfactant (DBSA) Concentration (ppm)

2

Figure 3: Fractional yield curve for solid-free asphaltene measured at different DBSA

3

concentration (0, 5000, 10000, 15000, and 25000 ppm) for various volumetric fractions of

4

heptane (0.6, 0.7, 0.8, and 0.9).

5 6

Effect of DBSA Surfactant on Asphaltene Deposition on Packed Bed

7

Stainless steel (SS) beads: In the first step, the amount of the trapped fluid between the stainless

8

steel (SS) and glass beads was measured. Trapped fluid measurements were conducted using

9

bitumen with different n-heptane and DBSA concentrations. These measurements were

10

conducted with SS beads and then glass beads packed bed column. The results of 11 repeated

11

experiments showed that the measured values of the trapped fluid do not vary with n-heptane or

12

surfactant concentrations. Instead, they are scattered closely to a mean value of 0.2061 g for

13

stainless steel beads packed bed with standard deviation of 0.0422. For glass beads packed,

12 ACS Paragon Plus Environment

Page 13 of 25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

1

similar pattern is observed and a mean value of 0.1377 g with standard deviation of 0.0112.

2

Figure 4 shows how the trapped fluid appears in the packed bed surrounding some beads

3

adjacent to the glass walls.

4

5 6

Figure 4: Trapped fluid as it appears in the packed bed column using glass beads.

7

We study flow of diluted bitumen through a packed bed of stainless steel (SS) beads.

8

Destabilization of asphaltene in the diluted bitumen results in deposition on the stainless steel

9

packed bed. In this section, we report the n-heptane concentrations based on weight fraction.

10

Bitumen is a very viscous fluid at room temperature. Therefore, it cannot be agitated and mixed

11

with n-heptane perfectly. There is always possibility of formation of a region in the mixture with

12

high local concentration of n-heptane. To avoid of this problem, we mixed the bitumen with n-

13

heptane at a temperature higher than room temperature where the bitumen can be mixed with n-

14

heptane (70 to 80 ºC). To ignore the errors induced by evaporation of solvent, we report the

15

experiments in this section based on weight fraction of n-heptane in bitumen.

16

Asphaltene deposition weight after run-time of one day was measured and is shown in Figure 5.

17

Amount of asphaltene deposition was converted to specific deposition rate by dividing the mass

18

of the deposited asphaltene to time and surface area. We calculated the surface area by having 13 ACS Paragon Plus Environment

Energy & Fuels

1

the number of the beads, diameter of the beads, and the inner diameter of the tube. This figure

2

shows that the onset occurs between 55-58 wt.% of n-heptane and the deposition shows an

3

increasing trend reaching about 0.009 g/cm2/day at 70 wt.% of n-heptane. 0.010 Specific Deposition Rate (gr/cm2/day)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 14 of 25

0.008

0.006

0.004

0.002

0.000 0.4

4

0.5

0.6

0.7

0.8

Heptane Mass Fraction

5

Figure 5: Asphaltene deposition rate for Athabasca bitumen versus n-heptane concentration.

6

To study the effect of surfactant, DBSA was added and the specific deposition rate was

7

measured. Starting with 1000 ppm of DBSA (Figure 6), deposition rates were not altered or

8

shifted significantly and a similar trend was observed. A surfactant concentration of 10,000 ppm

9

results in higher deposition rate at higher n-heptane mass fractions. The trend shown by the

10

dashed line shows the asphaltene deposition in the absence of surfactant. This trend reveals that

11

deposition rates are higher in the presence of the surfactant. It was observed that surface of SS

12

beads has altered from being shinny and reflective type to dull, grey, and non-shiny surface when

13

exposed to DBSA concentration greater than 25,000 ppm as shown in Figure 7.

14 ACS Paragon Plus Environment

Page 15 of 25

0.012

2

Specific Deposition Rate (gr/cm /day)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

0 ppm 1,000 ppm 10,000 ppm 25,000 ppm

0.010

0.008

0.006

0.004

0.002

0.000 0.4

1

0.5

0.6

0.7

0.8

Heptane Mass Fraction

2

Figure 6: Specific asphaltene deposition rate on the stainless steel (SS) beads using Athabasca

3

bitumen with different n-heptane concentrations and different DBSA surfactant concentrations.

4

The dashed line shows deposition trend in the absence of surfactant.

5

6 7

Figure 7: Stainless steel (SS) bead surface appearance before (right) and after (left) exposure to

8

n-heptane/bitumen with DBSA concentrations of 25,000 ppm and above. 15 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 16 of 25

1

Figure 8 shows how the deposition mechanism is altered at high concentrations of DBSA. As

2

shown in the left picture, the asphaltene aggregates deposit in the space between the beads at low

3

DBSA concentrations. The most of the beads in the sides can be seen clearly with no deposit on

4

their surface. In contrast, at the concentrations higher than 25,000 ppm DBSA as seen in the right

5

picture, the deposits are sticking as a film layer on all beads surface in addition to the deposits

6

between the beads. To understand the effects of the surface, stainless steel beads was replaced by

7

glass beads and the same experiment was repeated.

8 9

Figure 8: Asphaltene deposition on stainless steel, (left) with no DBSA where the deposition

10

occurs between beads, and (right) stainless steel beads surface after running the experiments at

11

DBSA concentrations higher 25,000 ppm with asphaltene surrounding all beads surface area.

12

Glass beads: Depositional studies on glass beads have been reported in the literature. For

13

example, an experiment was done to study deposition of latex spheres on glass beads packed

14

bed. 17 Figure 9 shows that deposition on glass beads for bitumen/n-heptane mixture without

15

DBSA is similar to the one with stainless steel beads. The specific deposition rate is 2

16

mg/cm2/day at 60 wt.% of n-heptane and approaches 8 mg/cm2/day at 70 wt.% of n-heptane.

17

Addition of 10,000 ppm DBSA caused reduced deposition rate at 60 wt. % and 65 wt. %

18

compared to the results in the absence of surfactant. However, at higher n-heptane concentration

19

(e.g. 70 wt.%) the presence of the surfactant results in higher deposition rate, which may be

16 ACS Paragon Plus Environment

Page 17 of 25

1

attributed to experimental error. The results show that further addition of DBSA (25,000 ppm) at

2

all three weigh fractions of n-heptane decreases the asphaltene deposition on the glass bead

3

surface.

4

0.012 Specific Deposition Rate (gr/cm2/day)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

0.010 0 ppm 10,000 ppm 25,000 ppm

0.008

0.006

0.004

0.002

0.000 0.4

5

0.5

0.6

0.7

0.8

Heptane Mass Fraction

6

Figure 9: Specific asphaltene deposition rate in glass beads using Athabasca bitumen with

7

different n-heptane concentrations and different DBSA surfactant concentrations.

8

9

Figure 10 shows two examples of asphaltene deposits on glass beads packed bed. The picture on

10

the right (65 wt.% n-heptane and no DBSA) shows asphaltene depositing on around of the glass

11

beads. The left picture displays glass beads after 24 hr of run-time of experiments with 25,000

12

ppm of DBSA. As can be seen, there is significantly less asphaltene deposits on the system. It

13

can be concluded that surfactant has decreased the asphaltene deposition on glass surface.

17 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

1

Similarly, in the bulk system surfactant decreases the asphaltene precipitation (see Figure 3).

2

However, the surfactant increased the asphaltene deposition on stainless steel surface. The

3

surfactant molecule acts as a bridge between asphaltene molecules and stainless steel surface.

4

Therefore, DBSA is not recommended for flow assurance in steel pipelines.

Page 18 of 25

5

6 7

Figure 10: Asphaltene deposition on glass beads, (left) shows glass beads with no deposition

8

after using running the experiment with 65 wt.% of n-heptane in bitumen and concentration of

9

25,000 DBSA, (right) glass beads with deposited asphaltene on the surface of glass beads (no

10

DBSA).

11

During the measurement of deposition rates of the destabilized asphaltene from bitumen, each

12

sample was studied under the microscope to evaluate behaviour and size of the asphaltene

13

aggregates. This was conducted to relate the size and shape of asphaltene particles with the

14

deposition rate of the asphaltene. The smallest size can be seen in the microscope used in this

15

experiment was 0.5 µm (500 nm).

16

The difference in aggregate size and shape were compared between a sample stirred for about ~

17

24 hr and another sample that was circulated in the apparatus for ~24 hr. Figure 11 shows the

18

aggregate size for a fixed n-heptane concentration (63 wt.%) after 2 min stirring time (a) ,

19

followed by about 24 hr stirring (b) and 25 hr circulation in the apparatus (c). The results showed 18 ACS Paragon Plus Environment

Page 19 of 25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

1

that the stirred sample exhibits relatively bigger size reaching an average of 80 µm, while with

2

circulated sample asphaltene aggregate shows a mean size of about 40 µm.

3 4

Figure 11: Microscope images of n-heptane/bitumen mixture (63 wt. % of n-heptane) a) 2 min

5

of stirring after mixture preparation, b) after 23.5 hr of stirring without circulation in packed bed

6

column, c) after 23.5 hr of circulation in packed bed column.

7

Ability of DBSA surfactant to dissolve the deposited asphaltene

19 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 20 of 25

1

The ability of DBSA to dissolve the deposited asphaltene was examined. First, asphaltene was

2

deposited at n-heptane concentration of 65 wt.% and circulation run-time of 24 hr. Then, a new

3

sample of 65 wt.% n-heptane concentration was prepared with a pre-determined DBSA

4

concentration and circulated with a run-time of 24 hr. These experiments were performed using

5

both stainless steel and glass beads. The results are shown in Figure 12. The solid lines show the

6

baseline of the amount of asphaltene deposition on stainless steel and glass beads in the absence

7

of DBSA. Any points below these lines mean successful removal of asphaltene and any points

8

above indicate additional asphaltene deposition instead of removal. For stainless steel beads, it

9

can be seen that no successful removal is achieved even with 50,000 ppm, which was thought to

10

be enough to dissolve all asphaltene. In addition, data for stainless steel show that deposition

11

remains around 1 g followed by a decline as the concentration of DBSA is increased. On the

12

other hand, glass-bead curve shows a maximum deposition at 10,000 ppm followed by a sharp

13

decline. The results show that the deposited asphaltene has dropped below the base line

14

deposition in the absence of surfactant. At surfactant concentration of 50,000 ppm all asphaltene

15

deposits on glass surface have been removed effectively, which agrees with literature data that

16

shows DBSA dissolve all deposited asphaltene at 5% (50,000 ppm).3

17

These experiments confirmed stainless steel beads surface property alteration observed during

18

deposition experiments. The surface alteration that occurred during deposition significantly

19

changed the removal process. Adsorption properties are suspected to have made sticking of

20

asphaltene and DBSA aggregate to wall more favourable. The results suggest that surface

21

properties should be taken into account carefully when the surfactant is considered as asphaltene

22

dispersant in oil and gas industries. As seen in the previous section, surfactant can act as link

23

between asphaltene molecules and stainless steel surface. Traditional solvents such as xylene and 20 ACS Paragon Plus Environment

Page 21 of 25

1

aromatic hydrocarbons solvents do not interact with surface while the surfactant molecules can

2

interact actively with the surface. Therefore, the surface properties are not very important when

3

the traditional solvents are used. However, as shown here the interaction of surface and

4

surfactant molecules is critical.

1.4

Weight of Asphaltene (gr/day)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

Glass Bead

1.2 Stainless Steel 1.0 0.8 0.6

Glass bead with no surfactant

0.4579 0.4

0.4156 Stainless steel with no surfactant

0.2 0.0 0

10000

20000

30000

40000

50000

Concentration of DBSA (ppm)

5 6

Figure 12: Asphaltene deposited at 65 wt.% n-heptane flooded by a sample of asphaltene with

7

65 wt.% but with different DBSA concentration.

8

4. Summary and Conclusion

9

Asphaltene precipitation and deposition cause many problems such as clogging wells, flowlines,

10

and surface facilities in oil production operations, which cost companies millions of dollars due

11

to maintenance, replacement or loss of production issues. Recently, surfactant dispersants have

12

gained increasing interest. In this work, the effect of Dodecylbenzenesulfonic acid (DBSA) on

13

fractional yield of asphaltene in n-heptane/toluene mixture was studied. The results suggest that

21 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 22 of 25

1

DBSA surfactant decreases the asphaltene precipitation in the bulk system in the absence of a

2

surface, which is in agreement with the literature data. Moreover, the effects of DBSA as a

3

surfactant on asphaltene deposition on metal and glass surfaces have been studied.

4

In the presence of stainless steel surface, the surfactant increased the asphaltene deposition at

5

low surfactant concentrations. It was found that in this region, surfactants acted as a link between

6

asphaltene molecules and surface. The effect of surfactant on removal of deposited asphaltene

7

was studied. The results suggest that during the removal process asphaltene deposition increased

8

on both glass and stainless surfaces at low concentration of DBSA surfactant. The maximum

9

deposition rate for glass and stainless steel surfaces found to occur at 10,000 ppm and 20,000

10

ppm DBSA concentration, respectively. The results showed decline in deposition rate at higher

11

concentrations of DBSA. The decline in deposition rate is shown to be much faster for the glass

12

surface. At a DBSA concentration above 30000 ppm the deposited asphaltene on glass surface

13

starts to detach from the surface and the deposition rate reached below the originally deposition

14

base line. At a DBSA concentration of 50,000 ppm the whole deposited asphaltene was removed

15

from the glass surface. However, in case of stainless steel surface this was not possible and the

16

deposited asphaltene remained above the originally deposited level even at 50,000 ppm of DBSA

17

concentration. The results of this study highlights the importance of the surface properties when

18

a surfactant is used as asphaltene dispersant. In case of using aromatic solvents the role of

19

surface is not very important.

20

Acknowledgments

21

The authors would like to thank four anonymous referees for useful and constructive comments.

22

Abdulaziz Al Sultan would like to thank Saudi Aramco for financial support. The support of

22 ACS Paragon Plus Environment

Page 23 of 25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Energy & Fuels

1

NSERC IRC in Solvent Enhanced Recovery Processes and the Department of Chemical and

2

Petroleum Engineering and the Schulich School of Engineering at the University of Calgary is

3

also acknowledged.

4

References

5

1. Akbarzadeh, K.; Ahmed, H.; Dan, Z.; Stephan A.; Jefferson C.; Shah K.; Jamal A. J.;

6

Alan G. M.; Ryan P. R.; Oliver C. M. Asphaltenes - problematic but rich in potential.

7

Oilfield Review 2007, 22-43.

8 9 10 11 12 13

2. Subramanian, D.; Firoozabadi, A. Effect of surfactants and water on inhibition of asphaltene precipitation. Abu Dhabi International Petroleum Exhibition and Conference, Abu Dhabi, UAE, 9-12 Nov. 2015. SPE-177669-MS. 3. Hashmi, S. M.; Firoozabadi, A. Effective removal of asphaltene deposition in metalcapillary tubes. SPE J. 2016, 21 (5), 1747-1754. 4. Fávero, V. B. C.; Maqbool, T.; Hoepfner, M.; Haji-Akbari, N.; Fogler, H. S. Revisiting

14

the flocculation kinetics of destabilized asphaltenes. Adv. Colloid Interface Sci. 2017,

15

244, 267-280.

16

5. Chang, C.; Fogler H. S. Stabilization of asphaltenes in aliphatic solvents using

17

alkylbenzene-derived amphiphiles. 2. Study of the asphaltene-amphiphile interactions

18

and structures using fourier transform infrared spectroscopy and small-angle x-ray

19

scattering techniques. Langmuir 1994, 10 (6), 1758-66.

20 21 22 23

6. Wang, J.; Jill S. B.; Jefferson L. C. Asphaltene deposition on metallic surfaces asphaltene deposition on metallic surfaces. J Dispers Sci Technol. 2004, 25 (3), 287-98. 7. Aslan, S.; Firoozabadi, A. Effect of water on deposition, aggregate size, and viscosity of asphaltenes. Langmuir 2014, 30, 3658-3664. 23 ACS Paragon Plus Environment

Energy & Fuels 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

1

8. Subramanian, D.; Firoozabadi, A. Effect of surfactants and water on inhibition of

2

asphaltene precipitation. The Abu Dhabi International Petroleum Exhibition and

3

Conference. Abu Dhabi, UAE, 9-12 November 2015. SPE-177669-MS.

4 5 6

9. Subramanian, D.; Kathleen W.; Firoozabadi A. Ionic liquids as viscosity modifiers for heavy and extra-heavy crude oils. Fuel 2015, 143, 519-526. 10. Loureiro, T. S.; Luiz C.; Magalhães P.; Spinelli, L. S. Influence of precipitation

7

conditions (n-heptane or carbon dioxide gas) on the performance of asphaltene

8

stabilizers. J Pet. Sci. Eng. 2015, 127, 109-114.

9

11. Haddadnia, A.; Azinfar, B.; Zirrahi, M.: Hassanzadeh, H.; Abedi, J. Thermophysical

10

properties of dimethyl ether/Athabasca bitumen system, Can. J.Chem. Eng. 2017, DOI:

11

10.1002/cjce.23009

12

12. Nourozieh, H.; Kariznovi, M.; Abedi, J. Experimental and modeling studies of phase

13

behavior for propane/Athabasca bitumen mixtures. Fluid Phase Equilib. 2015, 397, 37-

14

43.

15 16 17

13. Sadeghi, H. Effect of refining on asphaltene property distributions. Thesis, University of Calgary. 2014 14. Azinfar, B.; Haddadnia, A.; Zirrahi, M.; Hassanzadeh, H.; Abedi, J. Effect of asphaltene

18

on phase behavior and thermophysical properties of solvent/bitumen systems. J. Chem.

19

Eng. Data 2017, 62 (1), 547-557.

20

Page 24 of 25

15. Fávero, V. B. C.; Hanpan, A.; Phichphimok, P.; Binabdullah, K.; Fogler, H. S.

21

Mechanistic investigation of asphaltene deposition. Energy Fuels 2016, 30 (11), 8915-

22

8921.

24 ACS Paragon Plus Environment

Page 25 of 25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

1

Energy & Fuels

16. Powers, D. P.; Sadeghi, H.; Yarranton, H. W.; and Van Den Berg, F. G. A. Regular

2

solution based approach to modeling asphaltene precipitation from native and reacted

3

oils: part 1, molecular weight, density, and solubility parameter distributions of

4

asphaltenes. Fuel 2016, 178, 218-233.

5 6

17. Elimeiech, M.; O’Melia, C. R. Kinetics of deposition of colloidal particles in porous media. Environ. Sci. Technol. 1990, 24 (10), 1528-1536.

7 8

25 ACS Paragon Plus Environment