Effective Trapping of Lithium Polysulfides Using a Functionalized

Subscriber access provided by University of Florida | Smathers Libraries

Article

Effective Trapping of Lithium Polysulfides Using a Functionalized Carbon Nanotube-Coated Separator for Lithium-Sulfur Cells with Enhanced Cycling Stability Rubha Ponraj, Aravindaraj Govindaraj Kannan, Jun Hwan Ahn, Jae Hee Lee, Joonhee Kang, BYUNGCHAN HAN, and Dong-Won Kim ACS Appl. Mater. Interfaces, Just Accepted Manuscript • DOI: 10.1021/acsami.7b10641 • Publication Date (Web): 16 Oct 2017 Downloaded from http://pubs.acs.org on October 18, 2017

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

ACS Applied Materials & Interfaces is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 29

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

Effective Trapping of Lithium Polysulfides Using a Functionalized Carbon Nanotube-Coated Separator for Lithium-Sulfur Cells with Enhanced Cycling Stability Rubha Ponraj,† Aravindaraj G Kannan,† Jun Hwan Ahn,† Jae Hee Lee,† Joonhee Kang,‡ Byungchan Han,‡ and Dong-Won Kim*,† † ‡

Department of Chemical Engineering, Hanyang University, Seoul 04763, Korea Department of Chemical and Biomolecular Engineering, Yonsei University, Seoul 03722, Korea

ABSTRACT The critical issues that hinder the practical applications of lithium-sulfur batteries, such as dissolution and migration of lithium polysulfides, poor electronic conductivity of sulfur and its discharge products and low loading of sulfur, have been addressed by designing a functional separator modified using hydroxyl-functionalized carbon nanotubes (CNTOH).

Density functional theory (DFT)

calculations and experimental results demonstrate that the hydroxyl groups in the CNTOH provoked strong interaction with lithium polysulfides and resulted in effective trapping of lithium polysulfides within the sulfur cathode side.

The reduction in migration of lithium polysulfides to the lithium anode

resulted in enhanced stability of the lithium electrode.

The conductive nature of CNTOH also aided

to efficiently reutilize the adsorbed reaction intermediates for subsequent cycling.

As a result, the

lithium-sulfur cell assembled with a functional separator exhibited a high initial discharge capacity of 1056 mAh g-1 (corresponding to an areal capacity of 3.2 mAh cm-2) with a capacity fading rate of 0.11% per cycle over 400 cycles at 0.5 C rate.

KEYWORDS: Lithium-sulfur cell, Carbon nanotube, Lithium polysulfide, Functional separator, Cycling stability

ACS Paragon Plus Environment

1


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 2 of 29

INTRODUCTION Development of advanced energy storage devices with high energy density and long cycle life is crucial for powering electric vehicles and utilizing renewable energy sources such as wind and solar energy.

In this regard, lithium-sulfur (Li-S) batteries are highly promising due to their high

theoretical energy density.1-3

In addition, sulfur is abundantly available, environmentally benign and

inexpensive. In Li-S batteries, cyclic sulfur is converted to Li2S through the formation of various lithium polysulfide intermediates during the discharge reaction.4 Unfortunately, higher order lithium polysulfide intermediates (Li2Sx, 4 ≤ x ≤ 8) dissolve in the electrolyte solution and migrate to the lithium anode side, resulting in the loss of active sulfur and damage of the lithium electrode surface.5 Also, sulfur and its discharge products are highly insulating in nature, which further limit their electrochemical performance.

These characteristics of the sulfur cathode result in rapid capacity

fading and low coulombic efficiency, which hinder their practical applications. To address these drawbacks, sulfur has been embedded into various forms of carbons, such as hierarchically porous carbon,6-7 hollow carbon spheres,8-10 carbon nanotubes,11 carbon nanofibers12 and graphene.13-16 Also, metal oxides including TiO2,17-18 MnO2,19-21 SiO222 and MgO23 have been utilized as functional additives in the sulfur cathode to trap the soluble lithium polysulfides within the cathode.

Other

strategies involve protecting the lithium anode,24-25 coating the active material with conductive polymers,26-28 using core-shell structured materials,29 optimizing the electrolyte composition,30-32 utilizing amino polar binder,33 and using lithium sulfide as an active material.34

Recently, the

functional materials such as carbon nanotube and graphene oxide have been used as an interlayer between the cathode and the separator to trap the polysulfides within the cathode side, resulting in enhanced cycling performance.35-42

For instance, Su and Manthiram37 demonstrated that a carbon

nanotube interlayer reduced the charge transfer resistance of the sulfur cathode and trapped lithium polysulfides within the cathode side, resulting in enhanced utilization of the active material and ACS Paragon Plus Environment

2

Page 3 of 29

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


improvement of cycling performance.

Another promising approach is the modification of the

separator using conductive materials, which integrate the functionalities of the interlayer while the separator acts as an electrically insulating membrane.

Since the conductive coating layer is supported

by the polymeric membrane, its weight and coating thickness can be reduced in comparison to the freestanding interlayer to achieve higher specific energy density.

In addition, integration of the

functional layer on to the separator avoids the complications related to modifying the cell configuration to accommodate the interlayer.

Various types of carbons such as Super P carbon, multi-walled carbon

nanotubes (MWCNT), acetylene black carbon and Ketjen black carbon, have been successfully explored as conductive coating layers on the separator.43-45 However, these carbon-based materials exhibited weak interaction with lithium polysulfides, which can trap lithium polysulfides only to a certain extent.18 To enhance the trapping ability of the carbon-based coating layers through chemical interaction, various strategies such as doping carbon with heteroatoms and adding additional functional materials have been adopted.46-49 Other effective strategy would be to enhance the cycling performance of lithium-sulfur cells by modifying the surface of carbon to achieve strong interactions with lithium polysulfides.

Most of the reports utilizing a surface-modified separator in Li-S cells have paid little

attention to areal capacity, which is a critical parameter to elevate these systems to the practical level.50 Although functionalized carbons have been explored in sulfur cathodes51-53 and as interlayers54-55 in LiS cells, to the best of our knowledge, the modification of separators using hydroxyl functionalized carbon materials in high areal density Li-S cells has been rarely explored so far. In this work, we demonstrate the effectiveness of using a hydroxyl functionalized carbon nanotube (CNTOH)-coated polyethylene (PE) separator to trap lithium polysulfides and enhance sulfur utilization in Li-S cells, as schematically demonstrated in Figure 1.

The hydroxyl groups in CNTOH

exhibited a strong interaction with lithium polysulfides, resulting in effective trapping of lithium polysulfides within the cathode side.

The reduction in migration of lithium polysulfides to the anode


3


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

side also resulted in enhanced stability of the lithium electrode.

Page 4 of 29

As a result, the Li-S cell assembled

with the CNTOH-coated separator exhibited higher initial discharge capacity and more stable cycling performance compared to the cells assembled with a pristine PE separator and a CNT-coated separator.

Figure 1. Schematic illustration of trapping lithium polysulfides by the CNTOH-coated separator. (a) The soluble lithium polysulfides migrate through the PE separator to the anode side, leading to low sulfur utilization. (b) For the CNTOH-coated separator, the soluble lithium polysulfides are trapped by the hydroxyl functional groups and reutilized to form short-chain polysulfides.

EXPERIMENTAL SECTION Surface Coating of Separator with CNTOH.

MWCNT (Hanwha Chemical, Korea) was surface-

functionalized using a hydrothermal method, as previously reported.56

In a typical synthesis, 2 g of

MWCNT was dispersed in 80 mL of 2 M sodium hydroxide solution and ultrasonicated for 30 min to achieve homogenous dispersion.

The solution was transferred into a 100 mL Teflon-lined stainless

steel autoclave and placed in a pre-heated oven at 180 °C for 4 h.

The reaction mixture was allowed

to cool down naturally, and the product was washed with methanol, ethanol and water sequentially until the pH became neutral.

Finally, the obtained product was dried overnight in a vacuum oven at ACS Paragon Plus Environment

4

Page 5 of 29

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


60 °C and used for separator coating.

For separator coating, 2.5 mg of CNTOH was dispersed in 300

mL of isopropanol using ultra-sonication for 2 h, and the solution was vacuum filtered through a commercial polyethylene (PE) separator (Asahi ND420) to achieve uniform coating on one side of the separator.

The coated separator was dried in a vacuum oven at 80 °C for 12 h and punched into

circular disks for performance evaluation. about 1.34 mg cm-2.

The weight of the CNTOH-modified PE separator was

A CNT-coated separator was also prepared as a control sample through the same

procedure, where CNTOH was replaced with CNT.

Electrode Preparation and Cell Assembly. The sulfur cathode was prepared by mixing sulfur powder, Teflonized acetylene black and Ketjen black carbon in a weight ratio of 70:15:15 in ethanol. The obtained slurry was pressed on to a stainless steel mesh and dried at 60 °C under vacuum for 15 h. The loading of sulfur was controlled to be 3 mg cm-2.

A 200 µm-thick lithium foil (Honjo Metal Co.

Ltd.) pressed onto on copper foil was used as the anode.

A coin-type (CR2032) Li-S cell was

assembled by sandwiching the surface-modified separator between the lithium anode and the sulfur cathode.

The cell was then injected with 30 uL electrolyte solution consisting of 1 M lithium

bis(trifluoromethanesulfonyl)imide (LiN(SO2CF3)2, LiTFSI) dissolved in a mixed solvent of 1,3dioxalane (DOL) and 1,2-dimethoxyethane (DME) (50:50 by volume) containing 0.4 M LiNO3 as an additive.

All cells were assembled in an argon filled glove box.

Characterization and Measurements.

The morphological analysis was carried out using a scanning

electron microscope (SEM, JEOL JSM 6701F) equipped with energy dispersive spectroscopy (EDS). A high-resolution transmission electron microscope (HRTEM, JEOL, JEM 2100F) was used to observe the morphology of the CNT and CNTOH samples.

The quantitative analysis of surface functional

groups in CNTOH was performed using X-ray photoelectron spectroscopy (XPS, VG Multilab ESCA


5


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

System, 220i). spectrometer.

Page 6 of 29

Raman spectroscopy was carried out using a Dongwoo Optron, MonoRa 780i Fourier transform infrared (FTIR) spectra of CNT and CNTOH were recorded using a

JASCO 760 IR spectrometer.

AC impedance measurements were conducted in order to measure

electrolyte resistance and interfacial resistances using a Zahner Electrik IM6 impedance analyzer in the frequency range of 1 mHz to 100 kHz with an amplitude of 10 mV. Charge and discharge cycling tests of the Li-S cells were carried out using battery test equipment (WBCS 3000, WonA Tech Co., Ltd.) at 25 oC.

Lithium Polysulfide (Li2S4) Adsorption Test. Lithium polysulfide was synthesized according to the procedure previously reported.57 In a typical synthesis, 2.75 mol of sulfur was dissolved in 1 mol of superhydride solution, and the resulting solution was dried under vacuum to obtain a yellow powder. Then, the product was washed with toluene and dried to obtain a fine yellow powder of Li2S4.

For the

lithium polysulfide adsorption test, 5 mg of Li2S4 was dissolved in 5 mL of tetrahydrofuran and 20 mg of CNT or CNTOH were added into the solution and stirred for 1 h. solution were taken before and after stirring to observe its color change. dried under vacuum for XPS analysis.

Digital photographs of the The precipitated product was

All procedures were carried out in an argon filled glove box.

Computational studies. Density functional theory (DFT) calculations were performed using Vienna ab-initio simulation package (VASP) program with the Perdew-Burke-Ernzerhof (PBE) exchangecorrelation functionals and the projector-augmented wave (PAW) as implemented.58-59 Total energy and force were converged within 10-5 eV and 0.05 eV Å-1, respectively.

Brillouin zone in the

reciprocal space were integrated by k-mesh grids 1 × 1 × 3 for CNT and CNTOH with cut-off energy of 500 eV.

Van der Waals interaction was described by the DFT-D3 correction method.


6

Page 7 of 29

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


RESULTS AND DISCUSSION MWCNTs were surface functionalized with hydroxyl groups using a hydrothermal process, as illustrated in Figure 2, which is a simple and easy procedure to scale up for large-scale applications.

Figure 2. Surface modification of CNT using the hydrothermal method to form CNTOH.

The morphologies of pristine CNT and CNTOH were characterized using SEM and TEM, and the resulting images are given in Figure 3.

Both the SEM and TEM images of CNT and CNTOH samples

did not show any difference in the morphology, indicating that the hydrothermal method used to functionalize MWCNTs gave negligible influence on its tubular morphology.

Figure 3. SEM images of (a) CNT and (b) CNTOH.

TEM images of (c) CNT and (d) CNTOH.


7


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 8 of 29

To investigate the influence of functionalization on the structural features of CNT, Raman spectra were obtained, and the results are shown in Figure 4a.

Both CNT and CNTOH samples showed

characteristic bands at 1572, 1356 and 2681 cm-1, corresponding to the G-, D- and G’- bands respectively.

The G-band arises from the sp2-hybridized carbon structures, and the D-band is from the

scattering from a defect which breaks the basic symmetry of carbon material. attributed to the overtone of D band.

The G’ band is

As given in Figure 4a, the ID/IG ratio increased from 0.695 to

0.859 after functionalization, indicating that functionalization of CNT with hydroxyl groups induced structural distortions.

The amount and nature of functional groups on the CNTOH surface was further

characterized using XPS.

The survey spectra of CNT and CNTOH in Figure 4b show the presence of

carbon and oxygen in both samples.

The detection of oxygen in CNT indicates that a trace amount of

oxygen-containing impurities are present in the sample.

It is noticeable that the intensity of the

oxygen peak significantly increased in CNTOH, which suggests that additional oxygen functional groups are incorporated onto the surface of CNTOH. The amount of oxygen in the CNT and CNTOH samples were measured to be 2.1 and 9.4 at.%, respectively, indicating that additional oxygencontaining functional groups are attached to the CNT surface upon hydrothermal reaction.

To

elucidate the types of functional groups incorporated onto the CNTOH surface, the high resolution C 1s XPS spectra of CNT and CNTOH were resolved, as shown in Figure 4c and d, respectively.

The C 1s

spectrum of CNT exhibited three peaks centered at 284.6, 287.2 and 288.5 eV, which can be ascribed to sp2-hybridized carbon, carbonyl and carboxyl groups, respectively.

In contrast, the high-resolution

C 1s spectrum of CNTOH showed a peak at 285.9 eV in addition to three peaks detected in the CNT sample.

This additional peak can be attributed to the hydroxyl functional groups attached to carbon,

thereby confirming that CNT was successfully functionalized with hydroxyl groups.

To further

validate these results, FTIR spectra of CNT and CNTOH were recorded and are given in Figure S1. When compared to the CNT spectrum, CNTOH showed additional peaks at 1634 and 3422 cm-1, where


8

Page 9 of 29

the band at 3422 cm-1 corresponds to the stretching vibrational mode of hydroxyl groups, and the band at 1634 cm-1 can be ascribed to the stretching mode of hydroxyl in an enol group.56 This result further confirms the successful hydroxylation of CNT using hydrothermal method.

CNT CNTOH G band D band

(b)

G' band ID/IG = 0.695

ID/IG = 0.859

500

1000

1500

2000

2500

CNT CNTOH

Intensity (arb. unit)


(a)

200

3000

300

400

-1

Raman shift (cm )

280

282

284

286

288

290

Binding energy (eV)

600

700

800

Binding energy (eV)

Exp. data 2 sp C-C -C=O -O=C-O Cumulative

(c)

500

Exp. data 2 -sp C-C -C-O -C=O -O=C-O Cumulative

(d)



1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


292

280

282

284

286

288

290

292

Binding energy (eV)

Figure 4. (a) Raman and (b) XPS survey spectra of CNT and CNTOH.

High resolution C 1s XPS

spectra of (c) CNT and (d) CNTOH.

CNTOH was coated on one side of a separator using the vacuum infiltration method. image of the pristine separator (Figure S2a) shows uniform porous morphology.

The SEM

In contrast, the

CNTOH-coated separator (Figure S2b) exhibits homogenous morphology with uniform distribution of


9


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

CNTOH without agglomeration.

Page 10 of 29

The pore structure of the CNTOH-coated separator is important for

polysulfide confinement in the Li-S cell.

Since the functionalized CNT was coated on the commercial

separator using vacuum filtration of the dispersed solution, it resulted in highly intertwined, random network structure of CNTOH on the separator surface.

The thickness of the coating layer was found

to be 8.4 µm from the cross-sectional SEM image of the CNTOH-coated separator presented in Figure 5a and the mass loading of CNTOH on the PE separator was about 0.14 mg cm-2.

Although the

surface SEM image of CNTOH-coated separator (Figure 5b) shows porous morphology, the pores are not continuous through the coating layer and are random in nature.

It increases the tortuosity for

polysulfide migration to the anode side thereby allowing ample interaction with the hydroxyl groups on the coating layer.

(a)

(b)

(c)

(d)

Figure 5. (a) Cross-sectional SEM image of the CNTOH-coated separator. (b) Surface SEM image of the CNTOH-coated separator and its EDS elemental mappings corresponding to (c) carbon and (d) oxygen.

As shown in Figure 5b-d, the CNTOH-coated separator showed uniform distribution of carbon and oxygen elements in the SEM EDS elemental mapping of the surface.

These results confirm that the


10

Page 11 of 29

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


PE separator is uniformly coated with CNTOH.

It can be also seen that the integrity of the coated

separator remains intact with no visual damage on the edges even after punching (Figure S2c-d), which suggests that CNTOH is firmly adhered to the PE separator.

After the separator was coated with

CNTOH, its ionic conductivity when soaked with liquid electrolyte remained almost unchanged (6.2 × 10-4 S cm-1) compared to that of a pristine separator (6.4 × 10-4 S cm-1). The cycling performance of the Li-S cells assembled with different separators was evaluated at a constant current rate of 0.5 C, where 1.0 C corresponded to a current density of 1675 mA g-1.

Prior to

the cycling performance evaluation, the Li-S cells were pre-conditioned at the 0.2 C rate for one cycle in the voltage range of 1.9 to 2.6 V, and the resulting charge-discharge voltage profiles are given in Figure 6a.

All cells showed an upper discharge plateau and a lower discharge plateau around 2.35 and

2.10 V, respectively.

The upper discharge plateau corresponds to the conversion of cyclic sulfur to

higher order lithium polysulfides that are soluble in the electrolyte solution. plateau arises from subsequent reactions to form insoluble Li2S. form sulfur through a two-step reaction.

The lower discharge

During charging, Li2S is reverted to

All cells showed similar capacity emanating from the upper

discharge plateau, indicating that a similar amount of sulfur was utilized in all cells to form lithium polysulfides.

However, the capacity corresponding to the lower discharge plateau was largest for the

Li-S cell with the CNTOH-coated separator and least for the cell with the pristine separator.

This

result shows that the formed soluble lithium polysulfides were not effectively utilized during subsequent reactions in the cell with the pristine separator.

This implies that the soluble polysulfides

migrated to the anode side, thereby resulting in reduced capacity from the lower discharge plateau.

In

contrast, the soluble lithium polysulfides were trapped by CNTOH on the CNTOH-coated separator and reutilized during the subsequent reaction. polysulfide migration test (Figure S3).

This postulate was validated using a lithium

In this test, a vial containing a solution of lithium polysulfide

dissolved in a DOL/DME solvent mixture was allowed to migrate through the separator to another vial


11


containing a solvent mixture without the dissolved polysulfides, and the color change was monitored with time.

In the case of the pristine separator, the color of the solvent mixture turned from colorless

to yellow, indicating the migration of dissolved lithium polysulfides through the separator.

In

contrast, for the CNTOH-coated separator, the solvent mixture remained transparent after 2 h, which demonstrates the effective trapping of soluble lithium polysulfides by the CNTOH-coated separator.

3.0

3.0 (a)

2.6 2.4 2.2 2.0 1.8

2.6

1st 50th 100th 150th 200th 250th 300th 350th 400th

2.4 2.2 2.0 1.8

Pristine separator CNT-coated separator CNTOH-coated separator

1.6

(b)

2.8

Voltage (V)

Voltage (V)

2.8

1.6

1.4

1.4

0

200

400

600

800

1000

1200

0

200

1800

1200

100 Pristine separator CNT-coated separator CNTOH-coated separator

80

800 60 600 40

400

20

200 0

0

100

200

300

800

1000

1200

1400

(d)

-1

(c)

400

Coulombic efficiency (%)

-1

120

Discharge capacity (mAh g )

1400

0

600

Specific capacity (mAh g )

Specific capacity (mAh g )

1000

400

-1

-1

Discharge capacity (mAh g )

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 12 of 29

1600

0.1 C 0.2 C

1400

0.5 C

0.1 C 1.0 C

1200

2.0 C

1000 800 600 400

Pristine separator CNT-coated separator CNTOH-coated separator

200 0 0

5

10

15

20

25

30

Cycle number

Cycle number

Figure 6. (a) Pre-conditioning charge-discharge voltage profiles of Li-S cells with different separators, (b) charge-discharge voltage profiles at various cycles of the Li-S cell assembled with CNTOH-coated separator at 0.5 C rate, (c) discharge capacities of the of Li-S cells with different separators at 0.5 C rate as a function of cycle number, and (d) discharge capacities of the Li-S cells with the C rates increasing from 0.1 to 2.0 C every five cycles.


12

Page 13 of 29

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


The long-term stability of the Li-S cells with different separators was evaluated at 0.5 C, and the charge-discharge voltage profiles the cell employing the CNTOH-coated separator are given in Figure 6b.

The initial discharge capacity was 1057.6 mAh g-1 based on the mass of sulfur in the cathode with

an initial coulombic efficiency of 98.4%. after 400 cycles.

The cell delivered a discharge capacity of 570.0 mAh g-1

The cycling performances of the Li-S cells assembled with different separators are

compared in Figure 6c.

As shown in this figure, the cell with the CNTOH-coated separator exhibited

the best cycling performance in terms of discharge capacity and cycling stability up to 400 cycles at 0.5 C rate in the voltage range of 1.8 to 2.6 V.

Although, the cell with the CNT-coated separator

exhibited better cycling stability than the cell with pristine separator, its cycling performance was inferior to the cell with the CNTOH-coated separator.

The discharge capacity delivered by the Li-S

cell with the CNTOH-coated separator after 400 cycles at the 0.5 C rate is similar to the discharge capacity exhibited by the cell with the CNT-coated separator after 100 cycles.

The Li-S cell with

CNTOH-coated separator maintained high and stable coulombic efficiency over 99.5% throughout cycling after initial cycles.

In contrast, the cells with CNT-coated separator and pristine separator

exhibited slightly low initial coulombic efficiency and the coulombic efficiencies fluctuated in the later cycles, which arise from the partial dissolution of lithium polysulfides and their migration to the anode side.

These results suggest that the hydroxyl groups in CNTOH provided stronger interaction with

lithium polysulfides, thereby trapping them more effectively, which resulted in increased utilization of sulfur in the cathode and enhanced cycling stability.

To the best of our knowledge, the cycling data of

the Li-S cell with the CNTOH-coated separator are better than the results reported so far for Li-S cells using other surface-modified separators considering the relatively high areal capacity and low fading rate, as given in Table 1. Note that the areal capacity of the Li-S cell with the CNTOH-coated separator in the present work is 3.2 mAh cm-2, which is higher than the other reported works.


13


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Table 1.

Page 14 of 29

Comparison of initial capacity and cycling stability of the Li-S cell in this work with those

reported in the cells using various surface-modified separators. Initial specific capacity (mAh g-1)

Initial areal capacity (mAh cm-2)

Final areal capacity (mAh cm-2)

No. of cycles

Fading rate (% per cycle)

C rate

Ref.

1056

3.20

1.71

400

0.11

0.5 C

This work

1307

2.61

1.19

500

0.11

0.2 C

43

1389

1.57

0.97

200

0.19

0.5 C

44

1350

2.36

1.29

500

0.10

0.2 C

45

1073

2.15

1.24

300

0.14

1.0 C

60

1216

1.88

1.12

500

0.08

0.5 C

61

1090

1.74

1.24

100

0.28

0.5C

62

946

1.67

1.44

100

0.13

1.0 C

63

1216

1.95

1.28

500

0.07

1.0 C

64

1362

1.91

1.42

100

0.25

0.2 C

65

1028

1.64

0.91

1200

0.037

0.5 C

46

1225

4.90

3.87

30

0.70

0.2 C

49

1259

5.50

4.00

100

0.27

0.2 C

66

953

6.00

3.15

100

0.47

0.2 C

63

1012

1.42

0.99

100

0.30

0.2 C

67

The effect of CNTOH on the rate capability was evaluated at various current rates with 5 cycles at each current rate.

In the rate capability test, the cells were fully charged at same low current rate (0.1 C)

and discharged at different current rates with increasing current rate from 0.1 to 2.0 C every five cycles. As shown in Figure 6d, the cell with the CNTOH-coated separator delivered higher discharge capacities at all current rates than the cell with the pristine separator and CNT-coated separator.

The


14

Page 15 of 29

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


main reason for the good rate performance is the conductive nature of CNTOH, which aided in reducing the charge transfer resistance.43 The enhanced rate performance can be also attributed to the increased stability of the lithium anode in the cell with the CNTOH-coated separator due to the trapping of dissolved lithium polysulfides within the cathode side.

Note that the discharge capacities

of the cells measured at 0.5 C rate (Figure 6d) are higher than those presented in Figure 6c. ascribed to different current rates during charging cycles.

It can be

In the cycling test, the cells were charged at

0.5 C rate and discharged at same current rate (0.5 C) to the 400th cycles after one pre-conditioning cycle at 0.2 C.

In contrast, the cells for rate capability test were charged at lower current rate (0.1 C)

for all the cycles and discharged at different current rates from 0.1 to 2.0 C every 5 cycles, which enabled higher utilization of sulfur during charging cycle resulting in higher discharge capacity. SEM analysis of the lithium electrode was performed before and after cycling, and the resulting images are shown in Figure 7. cycling (Figure 7a and b).

The pristine lithium electrode showed uniform morphology before

When the Li-S cell with the pristine separator was cycled, the lithium

electrode exhibited the extensive surface growth that was protruded from the electrode surface (Figure 7c and d).

In contrast, the lithium electrode cycled with the CNTOH-coated separator gave a

smoother surface morphology (Figure 7e and f).

To further investigate the chemical composition on

lithium surface, SEM EDS mapping was carried out and the results are given in Figure S4.

The

lithium electrode cycled with the pristine separator exhibited uniform and dense distribution of sulfur throughout the surface, indicating that the migrated lithium polysulfides got deposited on the surface of lithium metal.

Although some sulfur could be detected on the lithium electrode cycled with CNTOH-

coated separator, its intensity was very weak.

The smoother morphology and relatively less intense

sulfur distribution on lithium electrode cycled with CNTOH-coated separator demonstrate that the trapping of lithium polysulfides within the cathode side enhances the stability of the lithium electrode.


15


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Figure 7.

Page 16 of 29

(a, b) SEM images of pristine lithium metal, (c, d) the lithium anode cycled with pristine

separator and (e, f) the lithium anode cycled with CNTOH-coated separator.

Li-S cells were cycled in

the voltage range of 1.8 to 2.6 V at 0.5 C for 100 cycles.

To further understand the influence of CNTOH-coated separator on the electrochemical performance of Li-S cells, AC impedance of the cell was measured before and after cycling, and the results are presented in Figure S5.

All the impedance spectra show the presence of two semicircles.

The semicircle observed at the high to medium frequency region is related with the resistance of lithium ions (Rf) in the surface film formed on the electrode, and the semicircle in the low frequency range is attributed to the charge transfer resistance (Rct) at the interface between electrolyte and electrode.

The X-axis intercept at the high frequency is corresponding to the electrolyte solution

resistance (RS).

Before cycling (after one pre-conditioning cycle), all the cells showed the almost

same resistance.

After 400 cycles, both electrolyte resistance (RS) and interfacial resistances (Rf and

Rct) increased for all cells.

Interestingly, the cell with CNTOH-coated separator exhibited the lowest


16

Page 17 of 29

resistances among the cells, and the cell with pristine separator showed the highest resistance.

These

results demonstrate that the hydroxyl groups in CNTOH effectively trapped and reutilized soluble lithium polysulfides within the cathode side resulting in reduced Rf and Rct.

Experimental data Cumulative

Intensity(a.u.)

(e)

0

-1

SB

172

170

168

166

ST

164

162

160

158

156

Binding energy (eV)

(f)

Experimental data

Polythionate complex

Cumulative

Thiosulfate

Intensity (a.u.)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


172

0

S

B -1

ST

170

168

166

164

162

160

158

156

Binding energy (eV)

Figure 8. Photographs of the Li2S4 solution in THF containing (a) CNTOH and (b) CNT, and the Li2S4 solution containing (c) CNTOH and (d) CNT after stirring for 1 h.

High-resolution S 2p XPS

spectra of (e) Li2S4 and (f) CNTOH-Li2S4 mixture after stirring with CNTOH for 1 h.

The effect of hydroxyl groups in CNTOH on the interaction of soluble lithium polysulfides was investigated using XPS analysis after the Li2S4 adsorption test, and the results are presented in Figure 8. The Li2S4 adsorption test was carried out to examine the behavior of CNT and CNTOH in a simulated environment within the Li-S cell during cycling.

The initial color of the Li2S4 solution with CNTOH


17


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 18 of 29

(Figure 8a) or CNT (Figure 8b) was yellow, and then the yellow solution turned transparent after stirring with CNTOH for 1 h (Figure 8c).

In contrast, the color of the solution with CNT added

remained dark yellow (Figure 8d) even after stirring for 1 h.

These results demonstrate that the

hydroxyl groups in CNTOH effectively can trap lithium polysulfides.

To further elucidate the type of

interaction between lithium polysulfide and CNTOH, XPS analysis was performed on the Li2S4adsorbed CNTOH.

As shown in Figure 8e, the resolved high resolution S 2p XPS spectrum of Li2S4

showed peaks corresponding to bridging (SB0) and terminal sulfur atoms (ST-1), which is consistent with spectra of lithium polysulfides reported in previous studies.21,23,57 Upon interaction with CNTOH, the S 2p XPS spectrum of CNTOH-Li2S4 provided the additional peaks at higher binding energy, as depicted in Figure 8f.

The deconvoluted peak at higher binding energy indicates the presence of thiosulfate

and the polythionate complex, which denotes a strong interaction between CNTOH and Li2S4.21,68 The polythionate complex was formed by the catenation reaction and it acted as a transfer mediator for the insoluble short-chain lithium polysulfides.

The formation of thiosulfate was attributed to the

interaction of Li2S4 with the hydroxyl groups in CNTOH.

From these results, a strong interaction

between lithium polysulfide and hydroxyl groups in CNTOH could be validated. In order to understand the atomistic mechanism of the performance enhancement, binding energies between the discharge products of Li2Sn intermediates and CNTOH were obtained by DFT calculations.

The model systems of the CNT and CNTOH consist of 140 carbon atoms with a

diameter of 9.58 Å.

Binding energies of Li2Sn on CNT or CNTOH were defined as equation (1),

∆EB = E(CNT) + E(Li2Sn) – E(CNT+ Li2Sn) where CNT can be CNT or CNTOH.

(1)

As shown in Figure 9, the binding energies of Li2Sn clusters on

CNT and CNTOH revealed that the CNTOH shows stronger binding strength than CNT due to the additional interaction between Li and O in the hydroxyl group.

This result suggests that the OH in

CNTOH enhances interaction with lithium polysulfides and effectively confine Li2Sn in the cathode. ACS Paragon Plus Environment

18

Page 19 of 29

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Also, the possible binding configurations of Li2Sn clusters on CNT and CNTOH are demonstrated in Figure S6 denoting various possible orientations. Moreover, the binding energies between Li2Sn species and CNTOH are much higher than those between Li2Sn clusters and the recently reported amino groups,33 which indicate strong adsorption of lithium polysulfides by the OH in CNTOH to trap them within the cathode.

Figure 9. Theoretical calculations of binding energies for Li2Sn intermediates at six different lithiation stages (Li2S, Li2S2, Li2S3, Li2S4, Li2S6, and Li2S8) on CNT and CNTOH. The green and yellow balls represent lithium and sulfur, respectively.

CONCLUSIONS We demonstrated that a functional separator coated with CNTOH effectively trapped lithium polysulfides within the cathode side, resulting in improvement of the cycling performance of Li-S cells. The enhanced cycling performance was attributed to (a) the strong adsorption of lithium polysulfides by the hydroxyl groups in CNTOH to trap them within the cathode side, (b) the conductive nature of


19


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 20 of 29

CNTOH aiding in the effective reutilization of the adsorbed reaction intermediates and (c) the reduction in the migration of soluble lithium polysulfides to the anode side resulting in a stable lithium electrode.

These results highlight the importance of using functional groups in separators to strongly

bind the soluble lithium polysulfides, and it suggests that using such functional separators is an effective strategy to realize the potential of Li-S batteries on a practical level.

AUTHOR INFORMATION Corresponding Author *E-mail: [email protected] (D.-W. Kim) R. Ponraj and A. G. Kannan contributed equally in this work.

ACKNOWLEDGMENTS This work was supported by the Basic Science Research Program of the National Research Foundation of

Korea

(NRF),

funded

by

the

Ministry

of

Science,

ICT,

and

Future

Planning

(2014R1A2A2A01002154 and 2016R1A4A1012224).

ASSOCIATED CONTENT Supporting Information FTIR spectra of CNT and CNTOH, SEM images of pristine PE separator and CNTOH-coated separator, Lithium polysulfide trapping test using pristine and CNTOH-coated separators, SEM and EDS mapping images of lithium electrodes after cycling, AC impedance spectra of the Li-S cells and illustration of the binding configurations of Li2Sn clusters on CNT and CNTOH.

This material is

available free of charge via the Internet at http://pubs.acs.org/.


20

Page 21 of 29

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


REFERENCES (1) Peramunage, D.; Licht, S., A Solid Sulfur Cathode for Aqueous Batteries. Science 1993, 261, 1029-1032. (2) Manthiram, A.; Fu, Y.; Chung, S. H.; Zu, C.; Su, Y. S., Rechargeable Lithium-Sulfur Batteries. Chem. Rev. 2014, 114, 11751-11787. (3) Carbone, L.; Greenbaum, S. G.; Hassoun, J., Lithium Sulfur and Lithium Oxygen Batteries: New Frontiers of Sustainable Energy Storage. Sustainable Energy Fuels 2017, 1, 228-247. (4) Xu, R.; Belharouak, I.; Zhang, X.; Chamoun, R.; Yu, C.; Ren, Y.; Nie, A.; Shahbazian-Yassar, R.; Lu, J.; Li, J. C. M.; Amine, K., Insight into Sulfur Reactions in Li–S Batteries. ACS Appl. Mater. Interfaces 2014, 6, 21938-21945. (5) Manthiram, A.; Fu, Y.; Su, Y.-S., Challenges and Prospects of Lithium–Sulfur Batteries. Acc. Chem. Res. 2012, 46, 1125-1134. (6) Ji, X.; Lee, K. T.; Nazar, L. F., A Highly Ordered Nanostructured Carbon-Sulphur Cathode for Lithium-Sulphur Batteries. Nat. Mater. 2009, 8, 500-506. (7) He, G.; Ji, X.; Nazar, L., High "C" Rate Li-S Cathodes: Sulfur Imbibed Bimodal Porous Carbons. Energy Environ. Sci. 2011, 4, 2878-2883. (8) Jayaprakash, N.; Shen, J.; Moganty, S. S.; Corona, A.; Archer, L. A., Porous Hollow Carbon@Sulfur Composites for High-Power Lithium–Sulfur Batteries. Angew. Chem. 2011, 123, 6026-6030. (9) Zhou, W. D.; Wang, C. M.; Zhang, Q. L.; Abruna, H. D.; He, Y.; Wang, J. W.; Mao, S. X.; Xiao, X. C., Tailoring Pore Size of Nitrogen-Doped Hollow Carbon Nanospheres for Confining Sulfur in Lithium-Sulfur Batteries. Adv. Energy Mater. 2015, 5, 1401752.


21


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 22 of 29

(10) Zhang, C.; Wu, H. B.; Yuan, C.; Guo, Z.; Lou, X. W., Confining Sulfur in Double-Shelled Hollow Carbon Spheres for Lithium–Sulfur Batteries. Angew. Chem. Int. Ed. 2012, 51, 9592-9595. (11) Moon, S.; Jung, Y. H.; Jung, W. K.; Jung, D. S.; Choi, J. W.; Kim, D. K., Encapsulated Monoclinic Sulfur for Stable Cycling of Li–S Rechargeable Batteries. Adv. Mater. 2013, 25, 65476553. (12) Chen, Y.; Li, X.; Park, K.-S.; Hong, J.; Song, J.; Zhou, L.; Mai, Y.-W.; Huang, H.; Goodenough, J. B., Sulfur Encapsulated in Porous Hollow CNTs@CNFs for High-Performance Lithium-Sulfur Batteries. J. Mater. Chem. A 2014, 2, 10126-10130. (13) Wang, D. W.; Zeng, Q. C.; Zhou, G. M.; Yin, L. C.; Li, F.; Cheng, H. M.; Gentle, I. R.; Lu, G. Q. M., Carbon-Sulfur Composites for Li-S Batteries: Status and Prospects. J. Mater. Chem. A 2013, 1, 9382-9394. (14) Ji, L.; Rao, M.; Zheng, H.; Zhang, L.; Li, Y.; Duan, W.; Guo, J.; Cairns, E. J.; Zhang, Y., Graphene Oxide as a Sulfur Immobilizer in High Performance Lithium/Sulfur Cells. J. Am. Chem. Soc. 2011, 133, 18522-18525. (15) Wang, Z.; Dong, Y.; Li, H.; Zhao, Z.; Bin Wu, H.; Hao, C.; Liu, S.; Qiu, J.; Lou, X. W., Enhancing Lithium–Sulphur Battery Performance by Strongly Binding the Discharge Products on Amino-Functionalized Reduced Graphene Oxide. Nat. Commun. 2014, 5, 5002. (16) Xu, N.; Qian, T.; Liu, X.; Liu, J.; Chen, Y.; Yan, C., Greatly Suppressed Shuttle Effect for Improved Lithium Sulfur Battery Performance through Short Chain Intermediates. Nano Lett. 2017, 17, 538-543. (17) Tao, X.; Wang, J.; Ying, Z.; Cai, Q.; Zheng, G.; Gan, Y.; Huang, H.; Xia, Y.; Liang, C.; Zhang, W.; Cui, Y., Strong Sulfur Binding with Conducting Magnéli-Phase TinO2n–1 Nanomaterials for Improving Lithium–Sulfur Batteries. Nano Lett. 2014, 14, 5288-5294.


22

Page 23 of 29

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


(18) Wei Seh, Z.; Li, W.; Cha, J. J.; Zheng, G.; Yang, Y.; McDowell, M. T.; Hsu, P.-C.; Cui, Y., Sulphur–TiO2 Yolk–Shell Nanoarchitecture with Internal Void Space for Long-Cycle Lithium– Sulphur Batteries. Nat. Commun. 2013, 4, 1331. (19) Liang, X.; Nazar, L. F., In-Situ Reactive Assembly of Scalable Core-Shell Sulfur-MnO2 Composite Cathodes. ACS Nano 2016, 10, 4192-4198. (20) Li, Z.; Zhang, J.; Lou, X. W., Hollow Carbon Nanofibers Filled with MnO2 Nanosheets as Efficient Sulfur Hosts for Lithium–Sulfur Batteries. Angew. Chem. Int. Ed. 2015, 54, 1288612890. (21) Liang, X.; Hart, C.; Pang, Q.; Garsuch, A.; Weiss, T.; Nazar, L. F., A Highly Efficient Polysulfide Mediator for Lithium–Sulfur Batteries. Nat. Commun. 2015, 6, 5682. (22) Campbell, B.; Bell, J.; Bay, H. H.; Favors, Z.; Ionescu, R.; Ozkan, C. S.; Ozkan, M., SiO2-Coated Sulfur Particles with Mildly Reduced Graphene Oxide as a Cathode Material for Lithium-Sulfur Batteries. Nanoscale 2015, 7, 7051-7055. (23) Ponraj, R.; Kannan, A. G.; Ahn, J. H.; Kim, D. W., Improvement of Cycling Performance of Lithium-Sulfur Batteries by Using Magnesium Oxide as a Functional Additive for Trapping Lithium Polysulfide. ACS Appl. Mater. Interfaces 2016, 8, 4000-4006. (24) Ma, G.; Wen, Z.; Wang, Q.; Shen, C.; Jin, J.; Wu, X., Enhanced Cycle Performance of a Li-S Battery Based on a Protected Lithium Anode. J. Mater. Chem. A 2014, 2, 19355-19359. (25) Shin, W.-K.; Kannan, A. G.; Kim, D.-W., Effective Suppression of Dendritic Lithium Growth Using an Ultrathin Coating of Nitrogen and Sulfur Codoped Graphene Nanosheets on Polymer Separator for Lithium Metal Batteries. ACS Appl. Mater. Interfaces 2015, 7, 23700-23707. (26) Je, S. H.; Hwang, T. H.; Talapaneni, S. N.; Buyukcakir, O.; Kim, H. J.; Yu, J.-S.; Woo, S.-G.; Jang, M. C.; Son, B. K.; Coskun, A.; Choi, J. W., Rational Sulfur Cathode Design for Lithium– Sulfur Batteries: Sulfur-Embedded Benzoxazine Polymers. ACS Energy Lett. 2016, 1, 566-572.


23


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 24 of 29

(27) Yang, Y.; Yu, G.; Cha, J. J.; Wu, H.; Vosgueritchian, M.; Yao, Y.; Bao, Z.; Cui, Y., Improving the Performance of Lithium–Sulfur Batteries by Conductive Polymer Coating. ACS Nano 2011, 5, 9187-9193. (28) Park, K.; Cho, J. H.; Jang, J.-H.; Yu, B.-C.; De La Hoz, A. T.; Miller, K. M.; Ellison, C. J.; Goodenough, J. B., Trapping Lithium Polysulfides of a Li-S Battery by Forming Lithium Bonds in a Polymer Matrix. Energy Environ. Sci. 2015, 8, 2389-2395. (29) Zhang, J. T.; Hu, H.; Li, Z.; Lou, X. W., Double-Shelled Nanocages with Cobalt Hydroxide Inner Shell and Layered Double Hydroxides Outer Shell as High-Efficiency Polysulfide Mediator for Lithium-Sulfur Batteries. Angew. Chem. Int. Ed. 2016, 55, 3982-3986. (30) See, K. A.; Wu, H.-L.; Lau, K. C.; Shin, M.; Cheng, L.; Balasubramanian, M.; Gallagher, K. G.; Curtiss, L. A.; Gewirth, A. A., Effect of Hydrofluoroether Cosolvent Addition on Li Solvation in Acetonitrile-Based Solvate Electrolytes and Its Influence on S Reduction in a Li–S Battery. ACS Appl. Mater. Interfaces 2016, 8, 34360-34371. (31) Cuisinier, M.; Cabelguen, P. E.; Adams, B. D.; Garsuch, A.; Balasubramanian, M.; Nazar, L. F., Unique Behaviour of Nonsolvents for Polysulphides in Lithium-Sulphur Batteries. Energy Environ. Sci. 2014, 7, 2697-2705. (32) Agostini, M.; Xiong, S.; Matic, A.; Hassoun, J., Polysulfide-Containing Glyme-Based Electrolytes for Lithium Sulfur Battery. Chem. Mater. 2015, 27, 4604-4611. (33) Chen, W.; Qian, T.; Xiong, J.; Xu, N.; Liu, X.; Liu, J.; Zhou, J.; Shen, X.; Yang, T.; Chen, Y.; Yan, C., A New Type of Multifunctional Polar Binder: Toward Practical Application of High Energy Lithium Sulfur Batteries. Adv. Mater. 2017, 29, 1605160. (34) Wang, L.; Wang, Y.; Xia, Y., A High Performance Lithium-Ion Sulfur Battery Based on a Li2s Cathode Using a Dual-Phase Electrolyte. Energy Environ. Sci. 2015, 8, 1551-1558.


24

Page 25 of 29

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


(35) Xiao, Z.; Yang, Z.; Wang, L.; Nie, H.; Zhong, M. e.; Lai, Q.; Xu, X.; Zhang, L.; Huang, S., A Lightweight TiO2/Graphene Interlayer, Applied as a Highly Effective Polysulfide Absorbent for Fast, Long-Life Lithium–Sulfur Batteries. Adv. Mater. 2015, 27, 2891-2898. (36) Balach, J.; Jaumann, T.; Klose, M.; Oswald, S.; Eckert, J.; Giebeler, L., Mesoporous Carbon Interlayers with Tailored Pore Volume as Polysulfide Reservoir for High-Energy Lithium–Sulfur Batteries. J. Phys. Chem. C 2015, 119, 4580-4587. (37) Su, Y.-S.; Manthiram, A., A New Approach to Improve Cycle Performance of Rechargeable Lithium-Sulfur Batteries by Inserting a Free-Standing Mwcnt Interlayer. Chem. Commun. 2012, 48, 8817-8819. (38) Chung, S.-H.; Singhal, R.; Kalra, V.; Manthiram, A., Porous Carbon Mat as an Electrochemical Testing Platform for Investigating the Polysulfide Retention of Various Cathode Configurations in Li–S Cells. J. Phys. Chem. Lett. 2015, 6, 2163-2169. (39) Wang, X.; Wang, Z.; Chen, L., Reduced Graphene Oxide Film as a Shuttle-Inhibiting Interlayer in a Lithium–Sulfur Battery. J. Power Sources 2013, 242, 65-69. (40) Kim, J. H.; Seo, J.; Choi, J.; Shin, D.; Carter, M.; Jeon, Y.; Wang, C.; Hu, L.; Paik, U., Synergistic Ultrathin Functional Polymer-Coated Carbon Nanotube Interlayer for High Performance Lithium– Sulfur Batteries. ACS Appl. Mater. Interfaces 2016, 8, 20092-20099. (41) Kim, H. M.; Hwang, J.-Y.; Manthiram, A.; Sun, Y.-K., High-Performance Lithium–Sulfur Batteries with a Self-Assembled Multiwall Carbon Nanotube Interlayer and a Robust Electrode– Electrolyte Interface. ACS Appl. Mater. Interfaces 2016, 8, 983-987. (42) Kong, W.; Yan, L.; Luo, Y.; Wang, D.; Jiang, K.; Li, Q.; Fan, S.; Wang, J., Ultrathin MnO2/Graphene Oxide/Carbon Nanotube Interlayer as Efficient Polysulfide-Trapping Shield for High-Performance Li–S Batteries. Adv. Funct. Mater. 2017, 27, 1606663.


25


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 26 of 29

(43) Chung, S. H.; Manthiram, A., A Polyethylene Glycol-Supported Microporous Carbon Coating as a Polysulfide Trap for Utilizing Pure Sulfur Cathodes in Lithium-Sulfur Batteries. Adv. Mater. 2014, 26, 7352-7357. (44) Chung, S.-H.; Manthiram, A., Bifunctional Separator with a Light-Weight Carbon-Coating for Dynamically and Statically Stable Lithium-Sulfur Batteries. Adv. Funct. Mater. 2014, 24, 52995306. (45) Yao, H.; Yan, K.; Li, W.; Zheng, G.; Kong, D.; Seh, Z. W.; Narasimhan, V. K.; Liang, Z.; Cui, Y., Improved Lithium-Sulfur Batteries with a Conductive Coating on Thes Eparator to Prevent the Accumulation of Inactive S-Related Species at the Cathode-Separator Interface. Energy Environ. Sci. 2014, 7, 3381-3390. (46) Balach, J.; Jaumann, T.; Klose, M.; Oswald, S.; Eckert, J.; Giebeler, L., Improved Cycling Stability of Lithium–Sulfur Batteries Using a Polypropylene-Supported Nitrogen-Doped Mesoporous Carbon Hybrid Separator as Polysulfide Adsorbent. J. Power Sources 2016, 303, 317-324. (47) Chang, C.-H.; Chung, S.-H.; Manthiram, A., Ultra-Lightweight Paninf/Mwcnt-Functionalized Separators with Synergistic Suppression of Polysulfide Migration for Li-S Batteries with Pure Sulfur Cathodes. J. Mater. Chem. A 2015, 3, 18829-18834. (48) Liu, W.; Jiang, J.; Yang, K. R.; Mi, Y.; Kumaravadivel, P.; Zhong, Y.; Fan, Q.; Weng, Z.; Wu, Z.; Cha, J. J.; Zhou, H.; Batista, V. S.; Brudvig, G. W.; Wang, H., Ultrathin Dendrimer–Graphene Oxide Composite Film for Stable Cycling Lithium–Sulfur Batteries. Proc. Natl. Acad. Sci. 2017, 114, 3578-3583. (49) Zhuang, T.-Z.; Huang, J.-Q.; Peng, H.-J.; He, L.-Y.; Cheng, X.-B.; Chen, C.-M.; Zhang, Q., Rational Integration of Polypropylene/Graphene Oxide/Nafion as Ternary-Layered Separator to Retard the Shuttle of Polysulfides for Lithium–Sulfur Batteries. Small 2016, 12, 381-389.


26

Page 27 of 29

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


(50) Lv, D.; Zheng, J.; Li, Q.; Xie, X.; Ferrara, S.; Nie, Z.; Mehdi, L. B.; Browning, N. D.; Zhang, J.G.; Graff, G. L.; Liu, J.; Xiao, J., High Energy Density Lithium–Sulfur Batteries: Challenges of Thick Sulfur Cathodes. Adv. Energy Mater. 2015, 5, 1402290. (51) Zu, C.; Manthiram, A., Hydroxylated Graphene–Sulfur Nanocomposites for High-Rate Lithium– Sulfur Batteries. Adv. Energy Mater. 2013, 3, 1008-1012. (52) Lee, J. S.; Manthiram, A., Hydroxylated N-Doped Carbon Nanotube-Sulfur Composites as Cathodes for High-Performance Lithium-Sulfur Batteries. J. Power Sources 2017, 343, 54-59. (53) Kim, J. H.; Fu, K.; Choi, J.; Sun, S.; Kim, J.; Hu, L.; Paik, U., Hydroxylated Carbon Nanotube Enhanced Sulfur Cathodes for Improved Electrochemical Performance of Lithium-Sulfur Batteries. Chem. Commun. 2015, 51, 13682-13685. (54) Huang, J.-Q.; Xu, Z.-L.; Abouali, S.; Akbari Garakani, M.; Kim, J.-K., Porous Graphene Oxide/Carbon Nanotube Hybrid Films as Interlayer for Lithium-Sulfur Batteries. Carbon 2016, 99, 624-632. (55) Zu, C.; Su, Y.-S.; Fu, Y.; Manthiram, A., Improved Lithium-Sulfur Cells with a Treated Carbon Paper Interlayer. Phys. Chem. Chem. Phys. 2013, 15, 2291-2297. (56) Yang, D.; Guo, G.; Hu, J.; Wang, C.; Jiang, D., Hydrothermal Treatment to Prepare Hydroxyl Group Modified Multi-Walled Carbon Nanotubes. J. Mater. Chem. 2008, 18, 350-354. (57) Pang, Q.; Kundu, D.; Cuisinier, M.; Nazar, L. F., Surface-Enhanced Redox Chemistry of Polysulphides on a Metallic and Polar Host for Lithium-Sulphur Batteries. Nat. Commun. 2014, 5, 4759. (58) Kresse, G.; Furthmüller, J., Efficient Iterative Schemes for Ab Initio Total-Energy Calculations Using a Plane-Wave Basis Set. Phys. Rev. B 1996, 54, 11169-11186. (59) Perdew, J. P.; Burke, K.; Ernzerhof, M., Generalized Gradient Approximation Made Simple. Phys. Rev. Lett. 1996, 77, 3865-3868.


27


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 28 of 29

(60) Chung, S.-H.; Manthiram, A., High-Performance Li–S Batteries with an Ultra-Lightweight Mwcnt-Coated Separator. J. Phys. Chem. Lett. 2014, 5, 1978-1983. (61) Balach, J.; Jaumann, T.; Klose, M.; Oswald, S.; Eckert, J.; Giebeler, L., Functional Mesoporous Carbon-Coated Separator for Long-Life, High-Energy Lithium-Sulfur Batteries. Adv. Funct. Mater. 2015, 25, 5285-5291. (62) Zhang, Z.; Lai, Y.; Zhang, Z.; Li, J., A Functional Carbon Layer-Coated Separator for High Performance Lithium Sulfur Batteries. Solid State Ionics 2015, 278, 166-171. (63) Zhao, D.; Qian, X.; Jin, L.; Yang, X.; Wang, S.; Shen, X.; Yao, S.; Rao, D.; Zhou, Y.; Xi, X., Separator Modified by Ketjen Black for Enhanced Electrochemical Performance of LithiumSulfur Batteries. RSC Adv. 2016, 6, 13680-13685. (64) Zhang, Z.; Wang, G.; Lai, Y.; Li, J.; Zhang, Z.; Chen, W., Nitrogen-Doped Porous Hollow Carbon Sphere-Decorated Separators for Advanced Lithium–Sulfur Batteries. J. Power Sources 2015, 300, 157-163. (65) Stoeck, U.; Balach, J.; Klose, M.; Wadewitz, D.; Ahrens, E.; Eckert, J.; Giebeler, L., Reconfiguration of Lithium Sulphur Batteries: “Enhancement of Li–S Cell Performance by Employing a Highly Porous Conductive Separator Coating”. J. Power Sources 2016, 309, 76-81. (66) Peng, H. J.; Wang, D. W.; Huang, J. Q.; Cheng, X. B.; Yuan, Z.; Wei, F.; Zhang, Q., Janus Separator of Polypropylene-Supported Cellular Graphene Framework for Sulfur Cathodes with High Utilization in Lithium–Sulfur Batteries. Adv. Sci. 2015, 3,1500268. (67) Chang, C.-H.; Chung, S.-H.; Manthiram, A., Effective Stabilization of a High-Loading Sulfur Cathode and a Lithium-Metal Anode in Li-S Batteries Utilizing Swcnt-Modulated Separators. Small 2016, 12, 174-179. (68) Yang, C.-P.; Yin, Y.-X.; Guo, Y.-G.; Wan, L.-J., Electrochemical (De)Lithiation of 1d Sulfur Chains in Li–S Batteries: A Model System Study. J. Am. Chem. Soc. 2015, 137, 2215-2218.


28

Page 29 of 29

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Table of Contents


29

Effective Trapping of Lithium Polysulfides Using a Functionalized

Recommend Documents