Subscriber access provided by UNIV OF DURHAM
Article
Enhanced hydrogen production from sawdust decomposition using hybrid-functional Ni-CaO-CaSiO materials 2
4
Guozhao Ji, Xiaoyin Xu, Hang Yang, Xiao Zhao, Xu He, and Ming Zhao Environ. Sci. Technol., Just Accepted Manuscript • DOI: 10.1021/acs.est.7b03481 • Publication Date (Web): 31 Aug 2017 Downloaded from http://pubs.acs.org on September 1, 2017
Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.
Environmental Science & Technology is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.
Page 1 of 29
Environmental Science & Technology
3
Enhanced hydrogen production from sawdust decomposition using hybrid-functional Ni-CaO-Ca2SiO4 materials
4
Guozhao Ji †,#, Xiaoyin Xu†,#, Hang Yang†, Xiao Zhao†, Xu He†, Ming Zhao*,†,‡
1 2
5
†
School of Environment, Tsinghua University, Beijing 100084, China
6
‡
Key Laboratory for Solid Waste Management and Environment Safety, Ministry of
7
Education, Beijing, 100084, China
8
Table of Content:
9
10
11
KEYWORDS. Biomass waste, hydrogen production, sawdust, thermal decomposition,
12
catalyst-sorbent hybrid
13
ABSTRACT. A hybrid-functional material consisting of Ni as catalyst, CaO as CO2
1
ACS Paragon Plus Environment
Environmental Science & Technology
Page 2 of 29
14
sorbent, and Ca2SiO4 as polymorphic ‘active’ spacer was synthesized by freeze drying
15
a mixed solution containing Ni, Ca and Si precursors, respectively, to be deployed
16
during sawdust decomposition that generated gases mainly containing H2, CO, CO2
17
and CH4. The catalytic activity showed a positive correlation to the Ni loading, but at
18
the expense of lower porosity and surface area with Ni loading beyond 20 wt.%,
19
indicating an optimal Ni loading of 20 wt.% for Ni-CaO-Ca2SiO4 hybrid-functional
20
materials, which enables ~ 626 ml H2 (room temperature, 1 atm) produced from each
21
gram of sawdust, with H2 purity in the product gas up to 68 vol.%. This performance
22
was superior over a conventional supported catalyst Ni-Ca2SiO4 that produced 443 ml
23
H2 g-sawdust-1 under the same operating condition with a purity of ~ 61 vol.%.
24
Although the Ni-CaO bi-functional material in its fresh form generated a bit more H2
25
(~ 689 ml H2 g-sawdust-1), its cyclic performance decayed dramatically, resulting in
26
H2 yield reduced by 62% and purity dropped from 73 to 49 vol.% after 15 cycles. The
27
‘active’ Ca2SiO4 spacer
28
Ni-CaO-Ca2SiO4 hybrid-functional material, corresponding to its minor loss in
29
reactivity over cycles (H2 yield reduced by only 7% and H2 purity dropped from 68 to
30
64 vol.% after 15 cycles).
offers
porosity
and
mechanical
strength
to
the
31
32
1. Introduction
33
The declining fossil fuel reserves and the raising concern about greenhouse gas 2
ACS Paragon Plus Environment
Page 3 of 29
Environmental Science & Technology
34
emission are the major challenges of the world energy and environment. Seeking for
35
alternative clean energies to meet the energy demand and environmental requirement
36
are of great interest for sustainable development. Among all the clean energy carriers,
37
hydrogen (H2) is one of the promising options due to the high calorific value and
38
pollutant-free emission.1 H2 could be generated via thermo-chemical processes from a
39
variety of sources including natural gas,2-4 coal,5, 6 chemical waste7 and biomasses.8-11
40
Unlike fossil fuels which have limited reserves and require high capital cost to exploit,
41
biomass is renewable, as such H2 production from waste biomass cycling such as
42
cellulose5, 10, 12-14 and sawdust15-17 via gasification has received growing attentions.
43
Another merit is that biomass gasification with CCS is a carbon-negative process,
44
because the released CO2 during biomass gasification with in-situ CO2 capture is less
45
than the CO2 consumed during the process of growth.
46
The current challenges of biomass gasification include incomplete tar cracking,
47
unreformed volatile fragments, and carbon deposition, etc. Nickel (Ni) has been
48
identified as one of the most efficient catalysts in cracking C-C, C-H, and O-H bonds as
49
well as enhancing water gas shift reaction,18-20 thus demonstrating high reactivity in tar
50
cracking and light-hydrocarbon reforming. As such, Ni-based catalysts have been
51
commonly used for steam reforming of methanol,21, 22 methane,23, 24 glycerol25, 26 and
52
ethanol.27, 28
53
Another challenge is that the application of H2 such as H2 fuel cells and float glass
54
production generally requires H2 purity up to 99%. However, there is still a gap
55
between the required H2 purity and the purity from biomass gasification. To enhance H2 3
ACS Paragon Plus Environment
Environmental Science & Technology
56
volumetric fraction from biomass, a feasible strategy is shifting the equilibrium of
57
reversible reactions (steam reforming, water gas shift, etc.) towards the H2 side. Since
58
carbon dioxide (CO2) is produced with H2 in water gas shift, capturing CO2 may shift
59
the water gas shift and thus convert more carbon monoxide (CO) and H2O to H2.
60
Calcium oxide (CaO), owing to its high sorption capacity and low cost, has been widely
61
used as CO2 sorbents,29-31 and also applied in sorption enhanced steam reforming to
62
promote the H2 yield.32-34 Meanwhile, CaO was found to be able to promote tar
63
cracking35-39 and catalyze char gasification,37, 40 both of which enhance the yield of
64
gaseous product during biomass pyrolysis. In view of these characteristics, CaO has
65
also been used as CO2 acceptor during biomass pyrolysis.9, 15, 41, 42 However, the poor
66
cyclic stability of CaO due to high temperature sintering deteriorates the CO2 sorption
67
performance.
68
Ca2SiO4 has been well investigated for its reversible polymorphic transitions with
69
swung temperatures.43 As per our recent research,44 Ca2SiO4 exhibited a strong ability
70
to resist particle sintering because the temperature-induced polymorphic transition
71
(α↔β) and the resulting volume expansion enabled Ca2SiO4 as an ‘active’ spacer to
72
‘automatically’ regenerate the declining porosity. For the hybrid-functional materials,
73
Ca2SiO4 hasn't been employed as stabilizer to prevent catalyst being sintered. To
74
demonstrate the superior sintering resistance with Ca2SiO4 over an “inert” spacer, the
75
most widely reported spacer Ca9Al6O1845-47 was chosen as the reference in this study.
76
Furthermore, the drying method for the precursor also has an effect on the material
77
structure. Freeze-drying, which sublimates the ice into vapor, avoids the pore-collapse 4
ACS Paragon Plus Environment
Page 4 of 29
Page 5 of 29
Environmental Science & Technology
78
caused by severe surface tension during direct liquid-gas transition, thus maintains the
79
pore and surface areas, which facilitates the mass transfer, catalysis and reactions.44, 48
80
The individual roles of Ni catalysts, CaO sorbent and Ca2SiO4 stabilizer have been
81
intensively studied in open literatures. However, limited research has been conducted
82
in applying a hybrid-functional material with Ni as catalyst, CaO as sorbent and
83
Ca2SiO4 as spacer to biomass pyrolysis. This work aimed at synthesizing a
84
hybrid-functional material Ni-CaO-Ca2SiO4 by freeze-drying method for enhancing the
85
hydrogen production during biomass decomposition. Sawdust, as a typical biomass
86
waste, was used as the model biomass. The proximate and ultimate analysis of sawdust
87
is given in Table S1.
88
89
2. Material and methods
90
2.1 Sample preparation
91
5 mmol tetraethyl orthosilicate (TEOS, Si(OC2H5)4) was dissolved into 1 mmol L-1
92
nitric acid (HNO3) and stirred at 600 r min-1 at room temperature for 40 min. 45 mmol
93
calcium acetate (Ca(C2H3O2)2, MW=176.18) and nickel (II) nitrate hexahydrate
94
(Ni(NO3)2·6H2O, MW=290.79) was then added to TEOS solution after TEOS was
95
completely hydrolyzed. The homogenous precursor was frozen at -80 ºC prior to the
96
24-h drying under vacuum. In order to examine the effect of Ni loading, the same
97
procedure was repeated with varied Ni content (5 wt.%, 10 wt.%, 15 wt.%, 20 wt.%, 5
ACS Paragon Plus Environment
Environmental Science & Technology
98
25 wt.% and 30 wt.%) by keeping constant CaO:Ca2SiO4 ratio (3:7). These samples
99
were denoted as Ni05, Ni10, Ni15, Ni20, Ni25 and Ni30, respectively.
100
For comparison purpose, three types of materials Ni-Ca2SiO4, Ni-CaO, and
101
CaO-Ca2SiO4 were also synthesized in a similar manner with the different recipe ratio.
102
The recipe details of each hybrid material were listed in Table S1. All of the
103
freeze-dried precursors were calcined at 850 ºC (ramping rate 5 ºC min-1) in air for 1h.
104
Reduction for activating Ni-catalysts was implemented under 5 vol. % H2 in nitrogen
105
(N2) for 1 hour at 750 ºC (ramping rate 5 ºC min-1).
106
Since lignocellulose accounts for over 90% of plant biomass.49 Sawdust, which
107
has rich lignocellulose content, was selected as biomass feedstock in this work. The
108
sieved particles (< 250 µm) were dried in oven at 60 ºC prior to the pyrolysis test.
109
2.2 Characterization
110
The crystalline structure of the hybrid materials was assessed using wide-angle X-ray
111
diffraction (XRD, D/Max 2500V+/PC, Cu Kα, 2θ=10~80°, step interval= 0.02°).
112
Scanning electron microscopy (SEM, Zeiss MERLIN VP Compact) was used to gain
113
insight of morphology. N2 physisorption using a Quantachrome autosorb iQ-C
114
instrument was carried out to detect the surface area, pore volume and mean pore size
115
of the materials.
116
2.3 H2 production test in TG-MS
117
The as-synthesized hybrid materials were mixed with sawdust with a constant mass 6
ACS Paragon Plus Environment
Page 6 of 29
Page 7 of 29
Environmental Science & Technology
118
ratio 2:1, and the mixed complex was decomposed at a ramping rate of 40 ºC min-1 to
119
850 ºC under the purging argon (Ar) at 500 ml min-1. A modified thermogravimetric
120
analyzer (SDT Q600) coupled with a mass spectrometer (Hiden HPR20) (TG-MS)
121
recorded the mass variation and gases yield during the pyrolysis, allowing the catalyst
122
activity and selectivity to be assessed. A semi-quantitative method was adopted to
123
interpret the online MS data. (Details and limitation discussion can be referred to from
124
our previous published works13, 14, 20, 50) The key m/z numbers used to represent the
125
major gas species were given in Table S2. The volumetric gas production, ml
126
g-sawdust-1, should be evaluated for normal conditions (room temperature, 1 atm).
127
128
3. Results and discussion
129
3.1 Material characterization
130
The N2 adsorption isotherms were plotted in Figure S1 for the hybrid-functional
131
materials with varied Ni loadings. Samples with Ni loading less than 20 wt.%
132
presented Type II isotherms which indicated a wide range of pore sizes of the
133
materials. The hysteresis implied the presence of meso-pores in these materials.51 The
134
sample Ni30, which contains 30 wt.% Ni, displayed type III isotherm with indistinct
135
hysteresis, suggesting the macro-porous structure of Ni30. Table 1 listed the textural
136
properties from N2 adsorption measurements. The BET surface area was maintained
137
similar to the value (~50 m2 g-1) of CaO-Ca2SiO4 when the Ni loading was increased 7
ACS Paragon Plus Environment
Environmental Science & Technology
Page 8 of 29
138
from 5 to 20 wt.%. Meanwhile, the pore volume and average pore size were close to
139
0.4 ml g-1 and 3.72 nm with just minor deviations. However, for the samples with Ni
140
loadings exceeding 20 wt.%, dramatic changes of the BET surface area and pore
141
volume were present. The surface area of Ni25 dropped to 28.83 m2 g-1, being only
142
half of the surface areas of lower Ni loading samples. The pore volume was deceased
143
significantly by 40%. With 30 wt.% Ni loading, Ni30 provided the lowest surface area,
144
and the average pore size (62.88 nm) indicated that Ni30 became macro-porous
145
material.
146
Table 1. Surface area, pore size and pore volume of materials with varied Ni loading Material
BET surface area (m² g‾¹)
Pore volume (ml g‾¹)
Pore size (nm)
CaO-Ca2SiO4
49.915
0.454
3.719
Ni05
52.901
0.434
3.717
Ni10
45.107
0.351
3.723
Ni15
45.332
0.408
3.719
Ni20
56.948
0.385
3.72
Ni25
26.832
0.241
3.939
Ni30
16.323
0.224
62.882
147 148
The XRD patterns of materials with varied Ni loadings presented the peaks of
149
NiO, CaO and Ca2SiO4, demonstrating the combinations of these three components
150
(Figure S2). As expected, the peaks corresponding to NiO became increasingly 8
ACS Paragon Plus Environment
Page 9 of 29
Environmental Science & Technology
151
evident with Ni loading increment. A possible impurity in the materials could be SiO2
152
which may resulted from incomplete reaction between TEOS and Ca(C2H3O2)2, but
153
SiO2, in the tested range of this work, cannot be detected from these XRD patterns
154
owing to its amorphous property.52
155
156 157
Figure 1. XRD patterns of all functional materials
158
Figure 1 also showed the XRD patterns of synthesized Ca2SiO4 and all the
159
functional materials (CaO-Ca2SiO4, Ni-CaO and Ni-Ca2SiO4). The hybrid-functional
160
material was also displayed in Figure 1 at the bottom for comparison. Ni-CaO did not
161
showed any unexpected peaks, suggesting it was produced without the presence of
162
any impurities, at least at the XRD detection level. Ca2SiO4 was synthesized by 9
ACS Paragon Plus Environment
Environmental Science & Technology
163
keeping the stoichiometry ratio of TEOS:Ca(C2H3O2)2=1:2 (Table S1), but the tiny
164
peaks of CaO in the Ca2SiO4 XRD patterns implied that the TEOS and Ca(C2H3O2)2
165
might not reach complete reaction. In view of this incomplete reaction, Ni-Ca2SiO4
166
may contain a small quantity of CaO, and the ratio of CaO:Ca2SiO4 in CaO-Ca2SiO4
167
and Ni-CaO-Ca2SiO4 could be slightly higher than 7:3.
168 169
Figure 2. SEM images of hybrid-functional materials with varied Ni loading. (a) 5
170
wt.% Ni loading, (b) 10 wt.% Ni loading, (c) 15 wt.% Ni loading, (d) 20 wt.% Ni
171
loading, (e) 25 wt.% Ni loading, and (f) 30 wt.% Ni loading. 10
ACS Paragon Plus Environment
Page 10 of 29
Page 11 of 29
Environmental Science & Technology
172
Figure 2 displayed the SEM images of hybrid-functional materials with varied Ni
173
loadings. The hybrid-functional material with 5 wt.% Ni loading was well dispersed
174
and showed the most uniform particle sizes (~ 50 nm) among all the hybrid-functional
175
materials. With increased Ni loading up to 20 wt.%, some grown particles were
176
observed, but particles were still dispersed with distinct gaps in between to form the
177
meso-porous structure. However, when Ni loading exceeded 25 wt.%, particles started
178
to agglomerate, and meso-pores was vanishing attributed to the coalescence of
179
particles, which was consistent with the findings in the N2 adsorption test (Table. 1
180
and Figure S1).
181
3.2 Effect of Ni loading on catalyst activity
182
The sawdust were mixed with hybrid-functional materials with various Ni loading and
183
decomposed in TG-MS. The evolved H2, CO and CO2 generation rates were plotted in
184
Figure 3. The details of converting the MS signal to volumetric flow rate was
185
provided in our previous work 14. The H2 generation started to be observable from 300
186
ºC and peaked around 400 ºC regardless of the Ni loading. However, the comparison
187
of peak intensities suggested that the hybrid-functional material with 20 wt.% Ni
188
loading produced the most H2. Since the major catalytic component in the
189
hybrid-functional material is Ni, with higher content of Ni, there would be more
190
active sites in the material, and thus higher catalytic activity could be expected. This
191
resulted in the H2 and CO production rates in the order of Ni05Ni10>Ni15 (Figure 3c). Since the total mass of material used in each test was
215
the same, lower Ni loadings in the material also means higher fractions of CaO in it,
216
and in turn more CO2 sorption in this material. The released CO2 at 650 ºC came from
217
the CO2 captured before this temperature. Since Ni05 contained the most CaO,
218
consequently it released the most CO2 finally.
219
The integrated yields of the H2, CO, CO2 CH4, and H2O were summarized in
220
Figure 4. The sawdust mixed with Ni20 (20 wt.% Ni loading) was the most
221
productive material in generating H2 and CO among all the hybrid-functional
222
materials. A general consideration of syngas quality for clean energy production is the 13
ACS Paragon Plus Environment
Environmental Science & Technology
Page 14 of 29
223
H2 purity as well as the lower heating value (LHV). The LHV of the product gas is
224
defined as:53, 54
LHV = (107.98 X H 2 + 126.36 X CO + 358.18 X CH4 )
225 226
where
227
respectively. Figure 4 inset displayed the H2 fraction in the total gas and the LHV
228
from per kilogram sawdust. The material with 20 wt.% Ni loading showed optimal H2
229
purity and heating value over those with other Ni loadings. The H2 volumetric fraction
230
could reach to 68% and the LHV is 9334 kJ kg-1. Hence Ni20 was selected to
231
represent the hybrid-functional material Ni-CaO-Ca2SiO4 in further experiments.
X H2
,
X CO
and
(1)
X CH 4
are the molar percentage of H2, CO and CH4,
232
233 234 235
Figure 4. Influence of Ni loading on the cumulative yield of major gases. Flow rate was calibrated at 20 ºC and 1 atm. Inset: Influence of Ni loading on the H2 14
ACS Paragon Plus Environment
Page 15 of 29
Environmental Science & Technology
236
fraction and lower heating value.
237
3.3 Effect of sawdust:hybridfunctional-material ratio on the gas yield
238
The effect of sawdust:hybrid-functional-material ratio on the pyrolysis product was
239
also systematically investigated by varying the mass ratio of sawdust to Ni20
240
(msaw:mmat) from 1:1 to 1:3. As demonstrated in Figure 5, increasing quantity of the
241
hybrid-functional material from msaw:mmat=1:1 to msaw:mmat=1:2 significantly
242
enhanced the H2 yield by 89%. However, further increasing the mass of
243
hybrid-functional material to msaw:mmat=1:3 failed to result in higher H2 yield. On the
244
contrary, 32% reduction of H2 was observed. Therefore, 1:2 was the optimum mass
245
ratio of sawdust to the hybrid-functional-material for the purpose of producing H2.
246
This ratio value was consistent with the value in Zhao et al.’s work for cellulose
247
decomposition using CaO, or Ni-Co.50
248 249
Figure 5. The cumulative gas yield under varied msaw:mmat ratio. Flow rate was
250
calibrated at 20 ºC and 1 atm. 15
ACS Paragon Plus Environment
Environmental Science & Technology
Page 16 of 29
251
3.4 Activity comparison against other functional material
252
The catalytic effect of hybrid-functional material (20 wt.% Ni loading) on the sawdust
253
decomposition was further compared with cases using three functional materials
254
(Ni-Ca2SiO4, Ni-CaO and CaO-Ca2SiO4). Figure 6a showed the H2 generation rates
255
from the hybrid functional materials. In addition, the case of pyrolyzing only sawdust
256
without any catalyst was also plotted as basis. The two cases (No Catalyst,
257
CaO-Ca2SiO4) in the absence of Ni merely produced little H2. The other three cases in
258
the presence of Ni (Ni-CaO-Ca2SiO4, Ni-Ca2SiO4 and Ni-CaO) generated remarkable
259
peaks for H2, demonstrating high activity of Ni in O-H and C-H cleavage. The H2
260
generation rate of the three Ni-containing materials followed the order of
261
Ni-CaO>Ni-CaO-Ca2SiO4>Ni-Ca2SiO4, which is also the order of CaO mass fraction
262
in each material. This order strongly suggested that H2 generation rate had a positive
263
correlation with CaO fraction. This is because the CO2 capture (Eq. (2)) shifted the
264
equilibrium of water gas shift reaction (Eq. (3)), and favored the H2 production
265
CaO + CO2 ⇌ CaCO3
(2)
266
CO + H2O ⇌ CO2 + H2
(3)
267
The CO generation rate with temperature by these hybrid functional materials
268
evolved very differently (Figure 6b). For the case with sawdust alone, there was only
269
one CO generation peak in identical temperature range as H2 peak. For other cases
270
with functional materials, secondary peaks were all observed at various temperatures.
271
The temperatures for the first peak in all cases were close to 390ºC. The 16
ACS Paragon Plus Environment
Page 17 of 29
Environmental Science & Technology
272
Ni-CaO-Ca2SiO4 generated more CO than Ni-CaO in the first peak range (300-450
273
ºC). They had equal Ni fraction. The major difference was the CaO fraction between
274
them. Ni-CaO contained more CaO which enhanced the water gas shift further in the
275
forward direction by capturing CO2, thus more CO was converted (Eq. (3)). On the
276
other hand, the presence of Ca2SiO4 in Ni-CaO-Ca2SiO4 may provide better stability
277
of the Ni catalytic activity, which could also be the reason of higher CO generation
278
rate.
279 280
Figure 6. Influence of different functional materials on the generation of major gases.
281
(a) H2, (b) CO, and (c) CO2. Flow rate was calibrated at 20 ºC and 1 atm. 17
ACS Paragon Plus Environment
Environmental Science & Technology
Page 18 of 29
282
Ni-CaO-Ca2SiO4 and Ni-Ca2SiO4 presented secondary CO peaks around 590 ºC
283
(Figure 6b). The secondary peaks of Ni-CaO and CaO-Ca2SiO4 appeared at relatively
284
higher temperature from 660 to 680 ºC. When Ni was together with Ca2SiO4, the
285
activity of Ni could be better maintained owing to the stability of Ca2SiO4. So the
286
secondary CO peak from Ni-CaO-Ca2SiO4 and Ni-Ca2SiO4 could probably come from
287
tar cracking. The tar cracking activity of Ni-CaO and CaO-Ca2SiO4 was not as high as
288
Ni-CaO-Ca2SiO4 and Ni-Ca2SiO4 due to the absence of stabilizer or catalyst. So the
289
CO generation peak of Ni-CaO and CaO-Ca2SiO4 may not come from tar cracking.
290
An interesting point is in Figure 6c only Ni-CaO and CaO-Ca2SiO4 showed CO2
291
secondary peaks. These CO2 generation came from CaCO3 calcination reaction (Eq.
292
(4))
293
294
CaCO3 ⇌ CaO + CO2
(4)
The released CO2 could further react with char by Boudouard reaction
295
CO2 + C ⇌ 2CO
296
Hence the CO generation of Ni-CaO and CaO-Ca2SiO4 appeared at 660 to 680 ºC
297
was a result of Eqs. (4) and (5). However many open literatures reported CO2
298
desorption at 800 ºC or above, 29, 31 so whether CO2 could be released from CaCO3 at
299
the temperature range of 660 to 680 ºC remains an issue. In order to address this point,
300
the fully carbonated CaO-Ca2SiO4 was heated for decarbonation under varied CO2
301
volume fractions, and the decarbonation temperature was derived from the most rapid
302
mass loss (Figure S3). The decarbonation temperature was 620 ºC when the CO2 18
ACS Paragon Plus Environment
(5)
Page 19 of 29
Environmental Science & Technology
303
fraction is zero. The CO2 fraction during sawdust decomposition in the TG-MS
304
system was evaluated in the order of 10-5 which is close to 0, demonstrating the
305
possibility of releasing CO2 from CaCO3 between 660 and 680 ºC. The occurrence of
306
Reaction (5) was also investigated by calculating the driving force term in Langmuir
307
Hinshelwood Hougen Watson (LHHW) kinetics. The driving force in Figure S4
308
proved Reaction (5) could occur from 600 ºC and above.
309
310
311
Figure 7. The mass variation and mass loss rate of sawdust with different
312
functional materials. Solid lines are mass and dashed lines are mass loss rate.
313
Figure 7 plotted the TGA curves during the sawdust decomposition with and 19
ACS Paragon Plus Environment
Environmental Science & Technology
314
without these functional materials. The case of only sawdust showed a single mass
315
loss near 390 ºC, which was in consistence with MS result in Figure 6. This
316
significant weight loss was observed in all cases in Figure 7, corresponding to the
317
volatile decomposition. The sawdust mixed with material containing CaO all showed
318
a remarkable additional weight loss around 660 ºC. This implied that reactions of
319
Eqns. (4) and (5) which reduce mass were occurring at the same time.
320
Ni-CaO-Ca2SiO4 and Ni-Ca2SiO4 showed a slight weight loss at about 590 ºC
321
attributed to the tar cracking by Ni. But the weight loss at this temperature range was
322
not noticeable in the case of Ni-CaO. These three materials all contained Ni, but
323
Ni-CaO failed in tar cracking. This implied that the catalytic activity of Ni could only
324
be maintained when it was loaded on stabilizers such as Ca2SiO4.
325
The integrated gas yields of H2, CO, CO2 and CH4 were summarized in Figure 8.
326
The hybrid-functional material Ni-CaO-Ca2SiO4 generated 41% higher H2 gas than
327
conventional supported Ni-Ca2SiO4 catalyst, and the H2 purity in the product gas was
328
also 11% higher (Figure 8 inset). The bi-functional material Ni-CaO performed better
329
than the hybrid-functional material Ni-CaO-Ca2SiO4 in producing H2. Meanwhile
330
Ni-CaO generated less CO than Ni-CaO-Ca2SiO4, indicating the enhancement of
331
water gas shift reaction by more CaO in Ni-CaO. The H2 purity in the product gas
332
(Figure 8 inset) followed the same order as the H2 accumulative yield, with the highest
333
purity up to 73 vol.% for Ni-CaO.
20
ACS Paragon Plus Environment
Page 20 of 29
Page 21 of 29
Environmental Science & Technology
334 335
Figure 8. Influence of different functional materials on the cumulative yield of
336
major gases and H2 purity in the product gas. Flow rate was calibrated at 20 ºC and 1
337
atm.
338
3.5 Cyclic stability demonstration
339
The functional materials were not designed to be one-off in practical application, thus
340
the cyclic stability of the material is of greater importance from an industrial
341
perspective. Although the hybrid-functional material Ni-CaO-Ca2SiO4 produced a bit
342
less H2 than Ni-CaO, due to the lower quantity of CaO in Ni-CaO-Ca2SiO4,
343
incorporating Ca2SiO4 spacers greatly stablized the material, maintaining the catalytic
344
activity and sorption capacity of the material over long-term operation. To
345
demonstrate
346
Ni-CaO-Ca2SiO4 and Ni-CaO, were treated for 15 carbonation-decarbonation cycles
347
prior to the catalytic decomposition of sawdust. The details of the 15 cyclic test was
348
plotted in Figure S5. After the 15 cycles, these two materials were mixed with
the
stablization
with
Ca2SiO4
spacers,
21
ACS Paragon Plus Environment
the
two
materials,
Environmental Science & Technology
349
sawdust for decomposition tested again in TG-MS. The accumulated gases yields
350
before and after the cyclic carbonation-decarbonation were compared in Figure 9.
351 352 353
Figure 9. The cyclic stabilities of Ni-CaO-Ca2SiO4 and Ni-CaO in decomposing sawdust. Flow rate was calibrated at 20 ºC and 1 atm.
354
Both materials showed decreased H2 yield and increased CO2 yield after the
355
cycles. Although the fresh bi-functional material Ni-CaO exhibited outstanding
356
performance in generating H2 prior to the carbonation-decarbonation cycles (Figure 8),
357
after the 15 cycles, its H2 yield decreased by 62%. Meanwhile, H2 purity in the
358
produced gas reduced from 73 vol.% down to 49 vol.%. However, the reduction of H2
359
yield for Ni-CaO-Ca2SiO4 was only 7% from 626 to 582 ml g-1, demonstrating superb
360
cyclic stability. The H2 purity before and after the cycles were 68 and 64 vol.%. After
361
the 15 cycles, the H2 yield by Ni-CaO-Ca2SiO4 was more than two times higher than
362
that generated by Ni-CaO. A deeper understanding of the different long-term stability 22
ACS Paragon Plus Environment
Page 22 of 29
Page 23 of 29
Environmental Science & Technology
363
could be performed by looking at the evolution of gas generation rates (Figure S6).
364
For Ni-CaO-Ca2SiO4, the H2 generation rate before and after 15 cycles did not show
365
any evident difference throughout the entire decomposition process. But for Ni-CaO,
366
the H2 generation rate at all temperatures was lower after 15 cycles, especially the H2
367
generation peak at 400 ºC was reduced from >300 ml min-1g-1 to less than 100 ml
368
min-1g-1. This was likely due to the catalyst deactivation during cycles. The material in
369
the absence of spacer failed to resist the sintering and lost some surface area and
370
porous structure, thus the exposed catalytic sites must have been significantly reduced.
371
As shown in Figure S6 (b), both materials presented reduction of CO genreation rate
372
at both two CO peaks after 15 cycles, but this decline was more remarkable for
373
Ni-CaO, especiall at the second CO peak. CO2 generation rate in Figure S6 (c) for
374
both Ni-CaO-Ca2SiO4 and Ni-CaO displayed some increases because of the reduced
375
CO2 capture efficiency after cycles, but the rise for Ni-CaO-Ca2SiO4 was very
376
marginal. Two increments of CO2 genreation rate were obvious for Ni-CaO ranging
377
from 410 to 550 ºC and from 700 to 800 ºC. This reduced CO2 sorption was also
378
probably owing to the sintering effect. Since CO2 in-situ sorption shows positive
379
correlation with H2 production, the poorer CO2 capture performance of Ni-CaO after
380
cycles (Figure S6 (c)) was also partially responsible for the H2 generation decline
381
(Figure S6 (a)).
382
In spite of the lower CaO quantity in hybrid-functional material Ni-CaO-Ca2SiO4,
383
the presence of Ca2SiO4 kept exellent long term stability and proved the necessity and
23
ACS Paragon Plus Environment
Environmental Science & Technology
384
advantage of having spacers in the hybrid-functional material. The long term stability
385
of Ca2SiO4 was also compared to the widely used stabilizer Ca9Al6O18. In the receipe
386
to synthesize Ni-CaO-Ca9Al6O18, the TEOS silica precursor was replaced by
387
Al(NO3)3.9H2O with proper quantity to form Ni-CaO-Ca9Al6O18, which has the
388
identical ratio of mNi:mCaO:mstabilizer. The comparison of gas yield before and after 15
389
cycles in Table S4 indicated a better stability of Ca2SiO4 than Ca9Al6O18, which was
390
likely due to the polymorphic transitions of Ca2SiO4. Figure S7 displayed the SEM
391
images of the functional materials before and after the 15 cycles. Ni-CaO showed
392
serious sintering effect. All the surface roughness and porous structure disappeared
393
after 15 cycles. The morphology change again confirmed the analysis above that the
394
catalyst deactivation and sorption decay was caused by sintering. However, the
395
presence of spacers Ca2SiO4 and Ca9Al6O18 evidently maintained the porous structure
396
after 15 cycles.
397 398 399
AUTHOR INFORMATION
400
Corresponding Author
401
* Phone: +86 10 6278 4701; Email:
[email protected] (MZ)
402
Author Contributions
403
#
404
Funding Sources
These authors contributed equally.
24
ACS Paragon Plus Environment
Page 24 of 29
Page 25 of 29
Environmental Science & Technology
405
National Natural Science Foundation of China (grant number: 51506112), the Tsinghua
406
University Initiative Scientific Research Program (grant number: 20161080094) and
407
China Postdoctoral Science Foundation (grant number: 2017M610910).
408 409
ACKNOWLEDGEMENTS
410
This work was supported by the National Natural Science Foundation of China (grant
411
number: 51506112) and the Tsinghua University Initiative Scientific Research Program
412
(grant number: 20161080094). G. Ji is grateful for the support by the International
413
Postdoctoral Exchange Fellowship Program and China Postdoctoral Science
414
Foundation (grant number: 2017M610910).
415 416
REFERENCES
417 418
1. Balat, M., Potential importance of hydrogen as a future solution to environmental and transportation problems. Int. J. Hydrogen Energy 2008, 33, (15), 4013-4029.
419 420
2. Heinzel, A.; Vogel, B.; Hübner, P., Reforming of natural gas—hydrogen generation for small scale stationary fuel cell systems. J. Powder Sources 2002, 105, (2), 202-207.
421 422 423
3. Lee, S. H. D.; Applegate, D. V.; Ahmed, S.; Calderone, S. G.; Harvey, T. L., Hydrogen from natural gas: part I—autothermal reforming in an integrated fuel processor. Int. J. Hydrogen Energy 2005, 30, (8), 829-842.
424 425
4. Ross, J. R. H., Natural gas reforming and CO2 mitigation. Catal. Today 2005, 100, (1–2), 151-158.
426 427 428
5. Jin, H.; Lu, Y.; Liao, B.; Guo, L.; Zhang, X., Hydrogen production by coal gasification in supercritical water with a fluidized bed reactor. Int. J. Hydrogen Energy 2010, 35, (13), 7151-7160.
429 430
6. Stiegel, G. J.; Ramezan, M., Hydrogen from coal gasification: An economical pathway to a sustainable energy future. Int. J. Coal Geol. 2006, 65, (3–4), 173-190.
431 432
7. McLellan, B.; Shoko, E.; Dicks, A. L.; Diniz da Costa, J. C., Hydrogen production and utilisation opportunities for Australia. Int. J. Hydrogen Energy 2005, 30, (6), 25
ACS Paragon Plus Environment
Environmental Science & Technology
433
669-679.
434 435
8. Ji, P.; Feng, W.; Chen, B., Production of ultrapure hydrogen from biomass gasification with air. Chem. Eng. Sci. 2009, 64, (3), 582-592.
436 437 438
9. Sreejith, C. C.; Muraleedharan, C.; Arun, P., Air–steam gasification of biomass in fluidized bed with CO2 absorption: A kinetic model for performance prediction. Fuel Process. Technol. 2015, 130, 197-207.
439 440 441
10. Khonde, R.; Chaurasia, A., Rice husk gasification in a two-stage fixed-bed gasifier: Production of hydrogen rich syngas and kinetics. Int. J. Hydrogen Energy 2016, 41, (21), 8793-8802.
442 443 444 445
11. Matsumoto, K.; Takeno, K.; Ichinose, T.; Ogi, T.; Nakanishi, M., Gasification reaction kinetics on biomass char obtained as a by-product of gasification in an entrained-flow gasifier with steam and oxygen at 900–1000 °C. Fuel 2009, 88, (3), 519-527.
446 447 448
12. Chaubey, R.; Sahu, S.; James, O. O.; Maity, S., A review on development of industrial processes and emerging techniques for production of hydrogen from renewable and sustainable sources. Renew. Sust. Energ. Rev. 2013, 23, 443-462.
449 450 451
13. Zhao, M.; Florin, N. H.; Harris, A. T., Mesoporous supported cobalt catalysts for enhanced hydrogen production during cellulose decomposition. Appl. Catal. B-Environ. 2010, 97, (1–2), 142-150.
452 453 454
14. Zhao, M.; Florin, N. H.; Harris, A. T., The influence of supported Ni catalysts on the product gas distribution and H2 yield during cellulose pyrolysis. Appl. Catal. B-Environ. 2009, 92, (1–2), 185-193.
455 456 457
15. Han, L.; Wang, Q.; Luo, Z.; Rong, N.; Deng, G., H2 rich gas production via pressurized fluidized bed gasification of sawdust with in situ CO2 capture. Appl. Energ. 2013, 109, 36-43.
458 459 460
16. Lv, P. M.; Xiong, Z. H.; Chang, J.; Wu, C. Z.; Chen, Y.; Zhu, J. X., An experimental study on biomass air–steam gasification in a fluidized bed. Bioresour. Technol. 2004, 95, (1), 95-101.
461 462 463 464
17. Chen, F.; Wu, C.; Dong, L.; Vassallo, A.; Williams, P. T.; Huang, J., Characteristics and catalytic properties of Ni/CaAlOx catalyst for hydrogen-enriched syngas production from pyrolysis-steam reforming of biomass sawdust. Appl. Catal. B-Environ. 2016, 183, 168-175.
465 466 467
18. Davda, R. R.; Shabaker, J. W.; Huber, G. W.; Cortright, R. D.; Dumesic, J. A., A review of catalytic issues and process conditions for renewable hydrogen and alkanes by aqueous-phase reforming of oxygenated hydrocarbons over supported metal 26
ACS Paragon Plus Environment
Page 26 of 29
Page 27 of 29
Environmental Science & Technology
468
catalysts. Appl. Catal. B-Environ. 2005, 56, (1–2), 171-186.
469 470
19. Sutton, D.; Kelleher, B.; Ross, J. R. H., Review of literature on catalysts for biomass gasification. Fuel Process. Technol. 2001, 73, (3), 155-173.
471 472 473
20. Zhao, M.; Church, T. L.; Harris, A. T., SBA-15 supported Ni-Co bimetallic catalysts for enhanced hydrogen production during cellulose decomposition. Appl. Catal. B-Environ. 2011, 101, (3–4), 522-530.
474 475 476
21. Takezawa, N.; Iwasa, N., Steam reforming and dehydrogenation of methanol: Difference in the catalytic functions of copper and group VIII metals. Catal. Today 1997, 36, (1), 45-56.
477 478 479
22. Laosiripojana, N.; Assabumrungrat, S., Catalytic steam reforming of methane, methanol, and ethanol over Ni/YSZ: The possible use of these fuels in internal reforming SOFC. J. Powder Sources 2007, 163, (2), 943-951.
480 481 482
23. Xie, M.; Zhou, Z.; Qi, Y.; Cheng, Z.; Yuan, W., Sorption-enhanced steam methane reforming by in situ CO2 capture on a CaO–Ca9Al6O18 sorbent. Chem. Eng. J. 2012, 207–208, 142-150.
483 484 485 486
24. Broda, M.; Manovic, V.; Imtiaz, Q.; Kierzkowska, A. M.; Anthony, E. J.; Müller, C. R., High-purity hydrogen via the sorption-enhanced steam methane reforming reaction over a synthetic cao-based sorbent and a ni catalyst. Environ. Sci. Technol. 2013, 47, (11), 6007-6014.
487 488
25. Lin, Y.-C., Catalytic valorization of glycerol to hydrogen and syngas. Int. J. Hydrogen Energy 2013, 38, (6), 2678-2700.
489 490 491
26. Freitas, A. C. D.; Guirardello, R., Comparison of several glycerol reforming methods for hydrogen and syngas production using Gibbs energy minimization. Int. J. Hydrogen Energy 2014, 39, (31), 17969-17984.
492 493 494
27. Sánchez-Sánchez, M. C.; Navarro, R. M.; Fierro, J. L. G., Ethanol steam reforming over – (, La, Zr and Mg) catalysts: Influence of support on the hydrogen production. Int. J. Hydrogen Energy 2007, 32, (10–11), 1462-1471.
495 496 497 498
28. Homs, N.; Llorca, J.; de la Piscina, P. R., Low-temperature steam-reforming of ethanol over ZnO-supported Ni and Cu catalysts: The effect of nickel and copper addition to ZnO-supported cobalt-based catalysts. Catal. Today 2006, 116, (3), 361-366.
499 500 501
29. Qin, C.; Yin, J.; Feng, B.; Ran, J.; Zhang, L.; Manovic, V., Modelling of the calcination behaviour of a uniformly-distributed CuO/CaCO3 particle in Ca–Cu chemical looping. Appl. Energ. 2016, 164, 400-410.
502
30. Qin, C.; Feng, B.; Yin, J.; Ran, J.; Zhang, L.; Manovic, V., Matching of kinetics of 27
ACS Paragon Plus Environment
Environmental Science & Technology
503 504
CaCO3 decomposition and CuO reduction with CH4 in Ca–Cu chemical looping. Chem. Eng. J. 2015, 262, 665-675.
505 506
31. Wang, S.; Yan, S.; Ma, X.; Gong, J., Recent advances in capture of carbon dioxide using alkali-metal-based oxides. Energ. Environ. Sci. 2011, 4, (10), 3805-3819.
507 508 509
32. Johnsen, K.; Ryu, H. J.; Grace, J. R.; Lim, C. J., Sorption-enhanced steam reforming of methane in a fluidized bed reactor with dolomite as -acceptor. Chem. Eng. Sci. 2006, 61, (4), 1195-1202.
510 511
33. Ding, Y.; Alpay, E., Adsorption-enhanced steam–methane reforming. Chem. Eng. Sci. 2000, 55, (18), 3929-3940.
512 513 514
34. Barelli, L.; Bidini, G.; Gallorini, F.; Servili, S., Hydrogen production through sorption-enhanced steam methane reforming and membrane technology: A review. Energy 2008, 33, (4), 554-570.
515 516 517
35. Florin, N. H.; Harris, A. T., Preparation and characterization of a tailored carbon dioxide sorbent for enhanced hydrogen synthesis in biomass gasifiers. Ind. Eng. Chem. Res. 2008, 47, (7), 2191-2202.
518 519 520
36. André, R. N.; Pinto, F.; Franco, C.; Dias, M.; Gulyurtlu, I.; Matos, M. A. A.; Cabrita, I., Fluidised bed co-gasification of coal and olive oil industry wastes. Fuel 2005, 84, (12–13), 1635-1644.
521 522 523
37. Yeboah, Y. D.; Longwell, J. P.; Howard, J. B.; Peters, W. A., Effect of calcined dolomite on the fluidized bed pyrolysis of coal. Ind. Eng. Chem. Process Des. Dev., 1980, 19, (4), 646-653.
524 525
38. Rapagnà, S.; Jand, N.; Foscolo, P. U., Catalytic gasification of biomass to produce hydrogen rich gas. Int. J. Hydrogen Energy 1998, 23, (7), 551-557.
526 527 528 529
39. Pérez, P.; Aznar, P. M.; Caballero, M. A.; Gil, J.; Martín, J. A.; Corella, J., Hot gas cleaning and upgrading with a calcined dolomite located downstream a biomass fluidized bed gasifier operating with steam−oxygen mixtures. Energ. Fuel. 1997, 11, (6), 1194-1203.
530 531
40. Lizzio, A. A.; Radovic, L. R., Transient kinetics study of catalytic char gasification in carbon dioxide. Ind. Eng. Chem. Res. 1991, 30, (8), 1735-1744.
532 533 534
41. Zhao, M.; Yang, X.; Church, T. L.; Harris, A. T., Novel CaO–SiO2 sorbent and bifunctional Ni/Co–CaO/SiO2 complex for selective H2 synthesis from cellulose. Environ. Sci. Technol. 2012, 46, (5), 2976-2983.
535 536 537
42. Hu, M.; Guo, D.; Ma, C.; Hu, Z.; Zhang, B.; Xiao, B.; Luo, S.; Wang, J., Hydrogen-rich gas production by the gasification of wet MSW (municipal solid waste) coupled with carbon dioxide capture. Energy 2015, 90, Part 1, 857-863. 28
ACS Paragon Plus Environment
Page 28 of 29
Page 29 of 29
Environmental Science & Technology
538 539 540
43. Remy, C.; Guyot, F.; Madon, M., High pressure polymorphism of dicalcium silicate Ca2SiO4. A transmission electron microscopy study. Phys Chem Miner 1995, 22, (7), 419-427.
541 542 543
44. Zhao, M.; Shi, J.; Zhong, X.; Tian, S.; Blamey, J.; Jiang, J.; Fennell, P. S., A novel calcium looping absorbent incorporated with polymorphic spacers for hydrogen production and CO2 capture. Energ. Environ. Sci. 2014, 7, (10), 3291-3295.
544 545 546
45. Chen, X.; Yang, L.; Zhou, Z.; Cheng, Z., Core-shell structured CaO-Ca9Al6O18@Ca5Al6O14/Ni bifunctional material for sorption-enhanced steam methane reforming. Chem. Eng. Sci. 2017, 163, 114-122.
547 548 549
46. Barelli, L.; Bidini, G.; Di Michele, A.; Gallorini, F.; Petrillo, C.; Sacchetti, F., Synthesis and test of sorbents based on calcium aluminates for SE-SR. Appl. Energ. 2014, 127, 81-92.
550 551 552
47. Radfarnia, H. R.; Iliuta, M. C., Development of Al-stabilized CaO–nickel hybrid sorbent–catalyst for sorption-enhanced steam methane reforming. Chem. Eng. Sci. 2014, 109, 212-219.
553 554
48. Zhao, J.; He, Y.; Zhang, L.; Lu, K., Preparation of porous TiO2 powder with mesoporous structure by freeze-drying method. J. Alloy. Compd. 2016, 678, 36-41.
555 556
49. Rinaldi, R.; Schuth, F., Design of solid catalysts for the conversion of biomass. Energ. Environ. Sci. 2009, 2, (6), 610-626.
557 558 559
50. Zhao, M.; Yang, X.; Church, T. L.; Harris, A. T., Interaction between a bimetallic Ni–Co catalyst and micrometer-sized CaO for enhanced H2 production during cellulose decomposition. Int. J. Hydrogen Energy 2011, 36, (1), 421-431.
560
51. Wilcox, J., Carbon Capture. Springer New York: 2012.
561 562 563
52. Liu, L.; Wang, D. K.; Martens, D. L.; Smart, S.; Strounina, E.; Diniz da Costa, J. C., Physicochemical characterisation and hydrothermal stability investigation of cobalt-incorporated silica xerogels. RSC Adv. 2014, 4, (36), 18862-18870.
564 565
53. Peng, L.; Wang, Y.; Lei, Z.; Cheng, G., Co-gasification of wet sewage sludge and forestry waste in situ steam agent. Bioresource Technol. 2012, 114, 698-702.
566 567 568
54. He, M.; Xiao, B.; Hu, Z.; Liu, S.; Guo, X.; Luo, S., Syngas production from catalytic gasification of waste polyethylene: Influence of temperature on gas yield and composition. Int. J. Hydrogen Energy 2009, 34, (3), 1342-1348.
29
ACS Paragon Plus Environment