Article pubs.acs.org/EF
Mercury Retention by Fly Ashes from Oxy-fuel Processes Nuria Fernández-Miranda, Marta Rumayor, M. Antonia Lopez-Anton,* Mercedes Díaz-Somoano, and M. Rosa Martínez-Tarazona Instituto Nacional del Carbón (CSIC), Francisco Pintado Fe 26, 33011 Oviedo, Spain ABSTRACT: The objective of this study is to determine the mechanism of mercury retention in fly ashes, the main solid waste from coal combustion power plants, and to evaluate the interactions between the type of mercury and fly ashes. The work was based on the results of mercury speciation in the gas and the solid fly ash before and after mercury retention. The identification of the mercury species in the gas was performed using previously validated methods, but the speciation of the mercury retained in the fly ashes was carried out using a mercury temperature-programmed desorption technique (HgTPD) still under development. The fly ashes were sampled from conventional coal combustion in air and oxy-combustion power plants. The main mercury species identified in the raw fly ashes and after they were subjected to an oxy-combustion atmosphere were mercury bound to organic matter and HgS, the ratio of these species depending on the characteristics of the ashes. The results obtained indicate that fly ashes are the route of mercury oxidation in an oxy-combustion atmosphere, although they hardly retain any mercury unless the unburned carbon content is high. HgTPD analysis shows that the main mechanism for mercury retention in the fly ashes is via the carbon matter.
1. INTRODUCTION The contribution of coal combustion to toxic mercury emissions to the environment and the problems that these emissions represent are well-known, as are the enormous efforts being made to reduce such emissions. Government organizations, researchers, and industry are all involved in this task.1 Several methods are already being investigated and, in some cases, implemented to prevent mercury emissions from coal combustion. To achieve this goal, it is necessary to have knowledge of the behavior of mercury along the process and of the interactions of this element with the subproducts produced in the power plant, such as fly ashes and gypsums. If the mercury species in combustion byproducts can be determined, the risk posed by these solids when they are reused or disposed of can be predicted. Mercury present in coal evaporates as elemental mercury (Hg0) during combustion, but it is partially transformed into oxidized species (Hg2+) as the flue gas cools. These species may react with the subproducts and be retained on the solids in different proportions and then be partially removed in the gas cleaning system. When interacting with the fly ashes, the main solid waste from coal combustion power plants, some mercury species may be adsorbed. As a consequence, a proportion of mercury can be captured in the particle control devices, resulting in a reduction of mercury emissions from the stack. However, mercury retention in fly ashes varies considerably depending on the type of coal and power plant.2−4 The need to understand mercury retention mechanisms in fly ashes and to identify the variables that modify retention efficiency has led to a wide body of research in this field that calls for an extensive review. Although such a review is outside the scope of this work, a summary of the most important conclusions of these research works can be attempted. No clear mechanism that explains how the different mercury species are retained in fly ashes has been satisfactorily established, probably because the retention of mercury in fly © 2015 American Chemical Society
ash occurs via more than one mechanism depending on the characteristics of the ashes and process conditions.5−9 However, the results obtained so far permit some generalizations that might be useful for industrial processes: (1) Regardless of the ash composition it can be stated that mercury is more easily retained in ashes with a high content in unburned coal particles.10−17 This affirmation has been verified in a number of works, although the precise mechanism via which sorption on carbon takes place has still not been clearly established. (2) If chlorides are present on the carbon surface, they play a significant role in the mechanism of oxidation/retention of mercury.18,19 However, the reason for this is even more difficult to explain than the effect of unburned particles. (3) Since mercury retention depends on the temperature of the flue gas at the point of collection2 and the retention is greater the longer the contact time between the gas and the ashes, mercury is more efficiently captured in power plants that are equipped with bag houses rather than electrostatic precipitators.20 Apart from the three factors just mentioned, other considerations such as (i) the role of the carbon structure on mercury adsorption and oxidation,4,13,21 (ii) the possibility that elemental mercury (Hg0) will be adsorbed onto the porous surface,4 (iii) the effect of mineral matter as a possible catalyst,14,22,23 and (iv) the mechanism responsible for chlorine−mercury reaction on the carbonaceous fraction of fly ashes24,25 still need to be addressed. The objective of the present work is to help clarify some of the previously mentioned points, focusing on the interaction between mercury species and fly ashes obtained from oxy-fuel combustion plants and coal combustion in air with two main Received: December 16, 2014 Revised: March 25, 2015 Published: April 7, 2015 2227
DOI: 10.1021/ef502827g Energy Fuels 2015, 29, 2227−2233
Article
Energy & Fuels Table 1. Combustion Parameters for the Three Sampled Power Stations fly ash
feed fuel
boiler
combustion condition
plant
CTCIU-A CTCIU-A/P CTCIU-R-A/P CTCIE CTP
anthracite anthracite/petcoke (70/30) anthracite/petcoke (70/30) sub-bituminous coal bituminous coal/coal wastes
FBC_1 FBC_1 FBC_1 FBC_2 FBC_3
oxy-fuel oxy-fuel oxy-fuel oxy-fuel air
30 MW 30 MW 30 MW 100 kW 50 MW
Figure 1. Schematic diagram of the experimental device.
electrostatic precipitator of a 50 MW power plant (FBC_3) operating in fluidized bed combustion in air. The chemical composition of the fly ashes was determined by X-ray fluorescence (XRF) using the ASTM D 4326 standard method. The chlorine content was analyzed by ion chromatography. The concentration of mercury in the raw fly ash samples was determined using an advanced mercury analyzer (AMA 254). The unburned carbon particle content was calculated as loss of ignition (LOI) by combustion of the organic matter at 815 °C. The Brunauer−Emmett−Teller (BET) surface area was measured by volumetric adsorption of nitrogen at 77 K. 2.2. Experimental Device for Mercury Retention. The tests for evaluating the interactions of mercury with the fly ashes were carried out in an experimental laboratory scale device illustrated in Figure 1. The device consisted of (1) a gas blending station equipped with mass flow controllers to prepare the gas composition that simulates a typical oxy-combustion atmosphere (64% CO2, 20% N2, 12% H2O, 4% O2, 1000 ppm SO2, 1000 ppm NO, 100 ppm NO2, and 25 ppm HCl), (2) a calibrated permeation tube (VICI Metronic) placed inside a glass “U” tube inmersed in a water bath to obtain 100 μg m−3 Hg0 in gas phase, (3) a glass reactor (length, 500 mm; diameter, 25 mm) where a sorbent bed is placed [the sorbent bed was prepared by mixing 0.05 g of fly ash with 0.65 g of sand in order to avoid an excess of pressure in the system, the reactor and the gases were kept at 150 °C, and he total volume of the flow gases that passed through the sorbent was 0.5 L·min−1], and (4) a continuous mercury analyzer (VM 3000) to monitor the Hg0. A Dowex 1 × 8 ion exchanger resin was used to determine the oxidized mercury (Hg2+).26,27 The resin was placed after the
objectives in mind: (i) to identify the differences that can be expected to result from these interactions in the relatively new oxy-combustion processes designed for CO2 capture and storage and conventional air combustion and (ii) to obtain new data that will improve our understanding of the mechanisms via which different species of mercury are retained in ashes of different characteristics. In addition, the knowledge of mercury speciation in fly ashes is important for evaluating the risks in the reutilization or disposal of wastes. The discussion of the results is based on the mercury speciation in the gas and the solid fly ash before and after they have been subjected to a gas atmosphere containing mercury. To identify mercury species in the solids a temperature-programmed desorption method (HgTPD) has been used.
2. MATERIALS AND METHODS 2.1. Fly Ash Samples. Fly ashes were obtained from three fluidized bed combustion plants. Plants 1 and 2 operated in oxy-combustion mode, whereas plant 3 functioned in conventional air combustion mode. The main characteristics of the power plants and the combustibles used are presented in Table 1. The three fly ash samples (CTCIU) from the 30 MW oxyfuel power plant (FBC_1) were taken from different sampling points. CTCIU-A and CTCIU-A/P were collected from the inlet pipe of the fly ash storage bin, while the fly ash labeled CTCIU-R-A/P was taken from the recirculation bin to the boiler. The CTCIE fly ash was obtained from the dust cyclone at the outlet of the flue gas pipe after the boiler in a 100 kW pilot plant (FBC_2). The fly ash CTP was sampled from the 2228
DOI: 10.1021/ef502827g Energy Fuels 2015, 29, 2227−2233
Article
Energy & Fuels
Table 2. Chemical Analysis, Mercury and Chorine Content, Unburned Carbon Content (LOI), and BET Surface Area of the Fly Ash Samples Na2O (%) MgO (%) Al2O3 (%) SiO2 (%) P2O5 (%) K2O (%) CaO (%) TiO (%) Fe2O3 (%) SO3 (%) Cl (μg/g) Hg (μg/g) LOI (%) BET (m2/g)
CTCIU-A
CTCIU-A/P
CTCIU-R-A/P
CTCIE
CTP
0.80 2.21 20.6 38.9 0.51 2.91 17.6 1.02 5.82 9.56 253 2.26 14.7 16.6
0.79 2.26 20.9 37.6 0.41 2.81 19.0 1.01 5.64 9.33 309 3.16 14.3 12.0
0.65 2.28 18.9 33.7 0.33 2.59 24.5 0.91 5.36 10.6 201 1.62 13.8 11.5
0.69 1.30 24.9 55.1 0.01 4.00 4.80 0.89 5.87 2.18 5563 1.14 27.5 38.8
0.66 1.44 22.8 54.2