MS Identification of Species-Specific Muscle Peptides in

Nov 10, 2017 - An innovative analytical strategy has been applied to identify signature peptides able to distinguish among processed animal proteins (...
0 downloads 13 Views 2MB Size
Subscriber access provided by READING UNIV

Article

LC-MS/MS identification of species-specific muscle peptides in processed animal proteins Daniela Marchis, Alessandra Altomare, Marilena Gili, Federica Ostorero, Amina Khadjavi, Cristiano Corona, Giuseppe Ru, Benedetta Cappelletti, Silvia Gianelli, Francesca Amadeo, Cristiano Rumio, Marina Carini, Giancarlo Aldini, and Cristina Casalone J. Agric. Food Chem., Just Accepted Manuscript • DOI: 10.1021/acs.jafc.7b04639 • Publication Date (Web): 10 Nov 2017 Downloaded from http://pubs.acs.org on November 10, 2017

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Journal of Agricultural and Food Chemistry is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 38

Journal of Agricultural and Food Chemistry

1

LC-MS/MS Identification of Species-specific Muscle Peptides in Processed Animal Proteins

2

Daniela Marchis *†┴, Alessandra Altomare ‡┴, Marilena Gili †, Federica Ostorero †, Amina Khadjavi

3



4

Cristiano Rumio #, Marina Carini ‡, Giancarlo Aldini ‡, Cristina Casalone †

, Cristiano Corona †, Giuseppe Ru †, Benedetta Cappelletti §, Silvia Gianelli ‡, Francesca Amadeo ‡,

5 6



7

10154, Torino, Italy

8



9

20133, Milano, Italy

Istituto Zooprofilattico Sperimentale del Piemonte, Liguria e Valle D’Aosta, via Bologna 148,

Department of Pharmaceutical Sciences, Università degli Studi di Milano, Via Mangiagalli 25,

10

§

11

#

12

Trentacoste 2, 20134, Milano, Italy

Italian Ministry of Health, Viale Giorgio Ribotta 5, 00144, Roma, Italy Department of Pharmacological and Biomolecular Sciences, Università degli Studi di Milano, Via

13 14

*Corresponding

author:

15

[email protected]

tel

+39

011

2686252;

fax

16 17 18 19 20 21 22 23 24 25 26

ACS Paragon Plus Environment

+39

011

2686237;

e-mail:

Journal of Agricultural and Food Chemistry

27

ABSTRACT

28

An innovative analytical strategy has been applied to identify signature peptides able to distinguish

29

among processed animal proteins (PAPs) derived from bovine, pig, fish and milk products.

30

Proteomics was first used to elucidate the proteome of each source. Starting from the identified

31

proteins and using a funnel based approach, a set of abundant and well characterized peptides with

32

suitable physical-chemical properties (signature peptides) and specific for each source were

33

selected. An on-target LC-ESI-MS/MS method (MRM mode) was set-up using standard peptides

34

and was then applied to selectively identify the PAP source and also to distinguish proteins from

35

bovine carcass and milk proteins. We believe that the method described meets the request of the

36

European Commission which has developed a strategy for gradually lifting the “total ban” towards

37

“species to species ban”, therefore requiring official methods for species-specific discrimination in

38

feed.

39 40

KEYWORDS: Processed animal proteins (PAPs), Bovine spongiform encephalopathy (BSE),

41

signature peptides, LC-QqLIT MS, bovine, pig, fish.

42 43 44 45 46 47 48 49 50 51 52

ACS Paragon Plus Environment

Page 2 of 38

Page 3 of 38

Journal of Agricultural and Food Chemistry

53

INTRODUCTION

54

Animal by-products are generally accepted as carcasses, hides, bones, meat trimmings, blood, fatty

55

tissues, horns, feet, hoofs or internal organs. In the past, meat by-products, the main source for meat

56

and bone meal, have been associated with exposure to the agent of bovine spongiform

57

encephalopathy (BSE),

58

specific legislation has been created regarding the handling and treatment of said by-products to at

59

least partially inactivate the prions. 3 In particular, under European legislation animal by-products

60

have been classified into three categories based on their potential risk to animals and the

61

environment. Categories 1-3 can be disposed of by incineration or rendering followed by landfill

62

disposal and only category 3 by-products may be used in the production of animal feedstuffs.

63

Processed animal proteins (PAPs) are animal proteins derived entirely from category 3 material

64

after specific regulated treatments. 3, 4

65

In the EU, PAPs are subject to strict controls to avoid any possible exposure of ruminants to prions.

66

An EU wide ban on the use of mammalian meat and bone meal for ruminants was first implemented

67

in 1994, then, to further restrict the possibility of cross-contamination in feed production, in January

68

2001 the feed ban was extended (“total feed ban”) to all farmed animals. 5-7 The latter measure has

69

played a major role in counteracting the circulation of the BSE agent leading to the EU-wide

70

decline of the BSE epidemic.

71

Commission to develop an exit strategy through two subsequent TSE Road Maps: 10, 11 within TSE

72

Road Map II a lift of the feed ban was expected to develop into a “species to species” ban, and since

73

June 2013 the total feed ban of PAPs has been partially lifted, allowing the use of non ruminant

74

PAPs in aquaculture. 12 The review of the total feed ban was envisaged as control tools were made

75

available both for official and self-monitoring laboratories. EU Regulation 51/2013 13 lays down the

76

official methods for determination of constituents of animal origin for the official control of feed.

77

According to this regulation, banned PAPs can be detected by light microscopy and polymerase

78

chain reaction (PCR). 13 Light microscopy identifies structures on the basis of their morphology and

1

the most known animal prion disease.

8, 9

2

In order to mitigate that risk,

3

The success in combatting the disease led the European

ACS Paragon Plus Environment

Journal of Agricultural and Food Chemistry

Page 4 of 38

79

enables identification of particles (such as bones, cartilages, muscle fibres, etc.),14-18 while PCR is

80

able to detect and identify the presence of specific animal DNA in feed.19-21 Nevertheless, even

81

combined, these methods sometimes do not succeed in determining the origin of the PAPs.

82

Moreover, although PCR analysis can detect ruminant DNA, it is unable to discriminate between

83

ruminant material from different origins (muscle and bones vs milk products, which are allowed to

84

be used). Thus, there is the risk of obtaining positive ruminant PCR signals from these authorized

85

materials.

86

addition of milk products in feed could mask a possible presence of ruminant PAP, and leave the

87

door open to potential fraud. As highlighted above, the presence of ruminant PAP in the feed chain

88

could be of some concern being a known risk factor for BSE.

89

Therefore, the recognition of species-specific markers for detection of PAPs, and tissue-specific

90

markers for an intra-specific discrimination of milk and meat products is highly desirable.

91

Moreover, both microscopy and PCR are qualitative methods. A tolerance level for PAP in feed for

92

farmed animals would be of great interest due to its implications in an international commercial

93

context. Different proteomics methodologies have been applied to study food products for species

94

identification,

95

contamination of pork and horse meat in beef matrix, using a shotgun proteomics approach to select

96

specific biomarker peptides.25 Recently, some researchers have focused their interest specifically on

97

PAPs. These are very heterogeneous and difficult matrices, due to the rendering treatments,

98

according to Annex VIII Regulation (EC) 142/2011.4 Peptide biomarkers of bovine plasma, blood

99

products and processed bovine proteins were identified using high-pressure liquid chromatography

22

Fish feed can contain both non ruminant PAP and milk products. At present, the

23, 24

and mass spectrometry techniques have been used to recognize trace

24, 26

100

coupled to electrospray ionization and tandem mass spectrometry in PAPs.

However, the

101

bovine selected peptides were from haemoglobin α and heat shock protein β-1 from blood products.

102

24

103

become leaky, allowing for the paracellular transfer of blood components into milk and vice

Blood proteins can be present in milk, as during an immune response, the blood-milk barrier can

ACS Paragon Plus Environment

Page 5 of 38

Journal of Agricultural and Food Chemistry

104

versa.27,

28

105

bovine heat stress response,29, 30 and somatic cells are widely known to be present in milk.

Heat shock proteins can be produced by mammary somatic cells, as involved in the

106

In this study, proteomics was applied to identify signature peptides able to distinguish among

107

PAPs derived from bovine, pig, fish and milk products. A liquid chromatography–tandem

108

quadrupole-linear ion trap (LC–QqLIT MS) method was then developed in order to identify such

109

signature peptides in PAPs and to confirm their selectivity. The proposed method was found

110

suitable to distinguish among PAPs from different species and also to distinguish proteins for

111

different tissues originating from the same species, as in the case of PAP from bovine carcass and

112

milk proteins.

113 114

MATERIALS AND METHODS

115

Samples

116

Two samples of commercial milk for zootechnical use, two samples of commercial whey powder,

117

one commercial fish meal, one pure commercial pork meal and one pure bovine meal provided by

118

the European Reference Laboratory on animal proteins in feed (EURL AP) were used. The purity of

119

each PAP was verified performing both pork and ruminant PCR analyses, according to the EURL

120

AP protocols.

121

Reagents

122

Formic acid, trifluoroacetic acid (TFA) and acetonitrile were LC-MS grade; sodium dodecyl sulfate

123

(SDS), and all other chemicals were analytical grade and purchased from Sigma-Aldrich (Milan,

124

Italy). Ultrapure water was prepared by a Milli-Q purification system (Millipore, Bedford, MA).

125

Any KD ™ Mini Protean TGX precast gel, Standard Precision Plus prestained protein standards,

126

Laemmli sample buffer (2X / 4X), Running buffer and Bio-Safe Coomassie, together with the

127

threo-1,4-dimercapto-2,3-butanediol (DTT) and iodoacetamide (IAA) were supplied by Bio-Rad

128

Laboratories, Inc. (Segrate, Italy). Trypsin was purchased from Roche Diagnostics SpA (Monza,

129

Italy). ACS Paragon Plus Environment

Journal of Agricultural and Food Chemistry

130

Standard peptides were synthesized by Primm Srl (Milano, Italy); peptides identification was

131

carried out by determining their molecular weights by MALDI-TOF analysis; purity (>95%) was

132

assessed by HPLC-UV analysis (λ 214 nm).

133

Digestion buffer was 50 mM ammonium bicarbonate; destaining solution was prepared mixing

134

acetonitrile with digestion buffer (1:1 v/v ratio); reducing solution was 10 mM DTT in digestion

135

buffer; alkylating solution was 55 mM iodoacetamide in digestion buffer; extraction solution (3%

136

TFA/30% acetonitrile in MilliQ H2O).

137

Sample Preparation

138

Protein extraction - Each sample was prepared in two replicates as follows: 800 µL of Laemmli

139

sample buffer 2X were added to 50 mg of PAP and incubated overnight at 85 °C in shaking

140

conditions (800 rpm) in a thermomixer (Eppendorf, Stevenage, UK). Samples were then centrifuged

141

at 22,000 x g for 30 min. Supernatant was transferred to another Eppendorf and diluted 1:6 (v/v) in

142

cold (-20°C) acetone and kept 1 h at -20 °C; after centrifugation (15 min at 20,000 x g, 4 °C),

143

supernatant was discarded and the pellet was washed with the same volume of cold (-20 °C)

144

acetone. After centrifugation, the first replicate was dissolved in 100 µL of SDS 1% solution to

145

determine the protein concentration by Bradford Assay.

146

The second replicate was used for SDS-PAGE analysis: 100 µL of Laemmli sample buffer 1X was

147

added to the pellet and incubated at 37 °C in the thermomixer under shaking conditions at 1000 rpm

148

overnight, until complete dissolution. In the case that the pellet did not completely dissolve, an

149

aliquot of 100 µL ultrapure water was added.

150

SDS-PAGE (reducing conditions) – 20 µL of raw extract in Laemmli sample buffer was mixed with

151

10 µL of Laemmli sample buffer 4X and 10 µL of 200 mM DTT and heated at 95 °C for 5 min.

152

Gel electrophoresis was performed using precast gel placed in a Mini-PROTEAN Tetra

153

electrophoresis cell (Bio-Rad Laboratories, Inc.) filled with running buffer and using a protein

154

mixture (Precision Plus Protein Standards) as standard. The electrophoretic run was conducted at

155

200 V (constant) for a variable time of about 30-40 min. Following the run, the gel was immersed in ACS Paragon Plus Environment

Page 6 of 38

Page 7 of 38

Journal of Agricultural and Food Chemistry

156

ultrapure water to remove any trace of running buffer and then stained for 1 h with Bio-Safe

157

Coomassie. After removing the excess stain in ultrapure water (2 h, under shaking) the images of

158

gels were acquired using a GS800 densitometer (Bio-Rad Laboratories, Inc).

159

In-gel tryptic digestion - Each band (ca. 1 cm width x 0.5 cm height) from the entire lane (10 bands

160

for proteomic studies and 5 for signature peptides identification by tandem MS) was cut using a

161

scalpel, finely chopped, transferred to an Eppendorf and washed with 200 µL of ultrapure water. An

162

aliquot of 200 µL of destaining solution was added to each gel portion and heated at 37 °C for 10

163

min in the thermomixer (1400 rpm); the destaining solution was then discarded and this step was

164

repeated until destaining was completed. Each gel portion was completely covered with acetonitrile

165

and heated at 37 °C for 5 min in the thermomixer (1400 rpm). Acetonitrile was removed and 200

166

µL of reducing solution was added and heated for 1 h at 56 °C in the thermomixer (300 rpm). After

167

removal of the reducing solution, the pieces of gel were washed with 100 µL of digestion buffer.

168

Gel portions were dried again with acetonitrile. Thiol residues were alkylated adding 200 µL of

169

alkylating solution for 45 min at room temperature in the dark. The alkylating solution was

170

discarded and the residue was washed in digestion buffer as previously described. 200 µL of

171

proteolytic enzyme solution, containing trypsin at a final concentration of 5 ng/µL in digestion

172

buffer was added to the gel portions and incubated overnight at 37 °C in the thermomixer (600

173

rpm).

174

The tryptic mixtures were acidified with formic acid up to a final concentration of 1%. To guarantee

175

better protein detection, an additional peptide extraction step was performed: 100 µL of extraction

176

solution was added to each gel portion and mixed in the thermomixer for 10 min at 37 °C at high

177

speed shaking (1400 rpm). The step was repeated twice followed by two steps using acetonitrile.

178

The four extracted fractions were then collected, mixed, dried in the Speed Vac (Martin Christ.,

179

Osterode am Harz, Germany) at 37 °C and finally stored at -20 °C until the time of analysis.

180

Signature peptides identification

ACS Paragon Plus Environment

Journal of Agricultural and Food Chemistry

181

Analytical Methods - Peptides from the in-gel digestion were separated by reversed-phase (RP)

182

nanoscale capillary liquid chromatography (nanoLC) and analyzed by electrospray tandem mass

183

spectrometry (ESI-MS/MS). The digests were resuspended in 20 µL of A (0.1% HCOOH),

184

vortexed for 15 min, centrifuged and loaded into 96-well multiwell plates to be analyzed. For each

185

analysis 5 µL of sample was injected onto a column by means of an autosampler; the column used

186

was a 75mm x 10cm, 2.7 mm particles, pores 100 Å, C18HALO PicoFrit column (New Objective,

187

USA). Samples were loaded onto the fused silica column at 400 nL/min of mobile phase consisting

188

of 99% A and 1% B (0.1% HCOOH in CH3CN) for 15 min. Peptide separation was performed with

189

a 55 min linear gradient of 1-35% B. The separative gradient was followed by 5 min at 80% B to

190

rinse the column, and 15 min of 99% A and 1% B served to re-equilibrate the column to the initial

191

conditions. The nano-chromatographic system, an UltiMate 3000 RSLCnano System (Dionex,

192

Thermo Scientific Inc., Milan, Italy), was connected to an LTQ-Orbitrap XL mass spectrometer

193

(Thermo Scientific) equipped with a nanospray ion source (dynamic nanospray probe, Thermo

194

Scientific) set as follows: positive ion mode, spray voltage 1.8 Kv; capillary temperature 220 °C,

195

capillary voltage 35 V; tube lens offset 120 V. The LTQ-Orbitrap XL mass spectrometer was

196

operated in data-dependent acquisition mode (DDA) to acquire both the full MS spectra and the

197

MS/MS spectra. Full MS spectra were acquired in "profile" mode, by the Orbitrap (FT) analyzer, in

198

a scanning range from m/z 300-1500, using a capillary temperature of 220 °C, AGC target = 5x105

199

and resolving power 60,000 (FWHM at m/z 400). Tandem mass spectra MS/MS were acquired by

200

the Linear Ion Trap (LTQ) in CID mode, automatically set to fragment the nine most intense ions in

201

each full MS spectrum (exceeding 1x104 counts) under the following conditions: centroid mode,

202

normal mode, isolation width of the precursor ion of m/z 2.5, AGC target 1x104 and normalized

203

collision energy of 35 eV. Dynamic exclusion was enabled (exclusion dynamics for 45 s for those

204

ions observed 3 times in 30 s). Charge state screening and monoisotopic precursor selection were

205

enabled, singly and unassigned charged ions were not fragmented. Xcalibur software (version 2.0.7,

206

Thermo Scientific) was used to control the mass spectrometer. ACS Paragon Plus Environment

Page 8 of 38

Page 9 of 38

Journal of Agricultural and Food Chemistry

207

Data processing - Proteins were identified using Proteome Discoverer 1.3 software (Thermo

208

Scientific), implemented with the algorithm SEQUEST. The databases used for data analysis were

209

downloaded

210

UniProt_SusScrofa.fasta (pig proteins), and a merged FASTA file obtained by combining all the

211

available fish species proteome databases (Lepisosteus oculatus, Danio rerio, Astyanax mexicanus,

212

Gasterosteus aculeatus, Takifugu rubripes, Xiphophorus maculatus, Oreochromis niloticus,

213

Tetraodon nigroviridis, Oryzias latipes, Poecilia formosa) for fish proteins; the search parameters

214

set in the workflow were all the experimental parameters used for mass spectra acquisition: mass

215

range between 350.0 Da - 5000.0 Da; any activation type mode; total intensity threshold 1; S/N

216

threshold 5; 5 ppm as precursor mass tolerance; and 0.5 Da as fragment mass tolerance; trypsin was

217

set as the proteolytic enzyme and 2 was the number of missed cleavages. Carbamidomethyation of

218

cysteine (+57.021 Da) was set as fixed modification while the oxidation of methionine (+15.995

219

Da) as variable modification.

220

To ensure the lowest number of false positives, the mass values experimentally recorded were

221

further processed through a combined search with the Database Decoy, where the protein sequences

222

are inverted and randomized. This operation allows the calculation of the false discovery rate (FDR)

223

for each match, so that all the proteins out of range of FDR between to 0.01 (strict) and 0.05

224

(relaxed) were rejected.

225

Once the task of matching with the UniProt database was completed, the resulting listing of proteins

226

was filtered under stringent conditions to ensure the lowest error probability (0.5%): only peptides

227

with medium/high confidence were accepted and all proteins recognized with less than two peptides

228

were excluded.

229

Identification of proteins to selectively distinguish between bovine PAP and milk products.

230

The Proteome Discoverer merging tool was applied to the lists of proteins found in bovine PAP and

231

milk products to identify their unique gene products. The candidate proteins were then filtered by

232

excluding all those proteins with a coverage of less than 20%, all enzymatic proteins (because it is

from

the

UniProt

web

site:

UniProt_BosTaurus.fasta

ACS Paragon Plus Environment

(bovine

proteins),

Journal of Agricultural and Food Chemistry

233

assumed that they have more than one conserved domain), and all the proteins previously detected,

234

by our research group, in bovine colostrum.31 An in depth bibliographic search allowed us to further

235

refine this list, excluding proteins previously identified in milk (bovine/human - breast/mature -

236

milk).

237

Identification of signature peptides - Identification of the signature peptides started from the multi-

238

consensus tabular reports obtained by merging all the protein-matches resulting from the MS data

239

elaboration (Proteome Discoverer 1.3). Uncharacterized proteins were not considered. Proteins

240

were then screened on the basis of their protein coverage (>20%), the score value (>200), the

241

number of unique peptides identified and the PSM (Peptide Spectral Match) number; the evaluation

242

of the last parameter is a good indicator of the abundance and good ionization properties of the

243

peptide. For each selected protein, the complete panel of peptides was refined considering several

244

factors: 1) the amino acids (aa) contained in the peptides (the presence of aa undergoing known

245

post translational modifications (PTMs) should be avoided) and the sequence of the peptide

246

(selected peptides should not contain in their sequence the proteolytic cleavage sites recognized by

247

trypsin or reactive or labile amino acid residues); 2) the protein-uniqueness of a peptide sequence

248

(prototypic-peptide); 3) the species-specificity; 4) the physicochemical properties of a peptide, that

249

can affect mass spectrometric sensitivity for a given mass spectrometer 32 and 5) the peptide length

250

(only peptides with a sequence composed of less than 20 aminoacidic residues were considered).

251

The final candidate peptides were aligned in the BLAST browser to exclude the conserved

252

sequences with the species examined.

253

LC-MS/MS meal extracts analysis

254

Analytical Method Development by LC-ESI-TSQ Quantum Triple Quadrupole

255

Chromatographic condition. The analyses were performed on a reversed-phase 75 x 2.1 mm, i.d.

256

2.6 µm, 100 Å, Kinetex Core-Shell Technology - C18 column (Phenomenex, Milan, Italy) with a

257

Kinetex security-guard column (Phenomenex, Milan, Italy), by using a Surveyor system (Thermo

258

Scientific) equipped with an autosampler kept at 8 °C working at a constant flow rate (300 µL/min). ACS Paragon Plus Environment

Page 10 of 38

Page 11 of 38

Journal of Agricultural and Food Chemistry

259

10 µL of standard solution was injected and peptides were eluted with a 38 min multistep gradient

260

of A (0.1% HCOOH) and B (0.1% HCOOH in CH3CN): 0-3 min, 3% B isocratic; 3-28 min, 3-70%

261

B; 28-30 min, 70-95% B; 30-33 min, 95% B isocratic; and then 5 min 3% B isocratic.

262

Characterization of MS/MS product ions for Multiple Reaction Monitoring analysis. A multiple

263

reaction monitoring (MRM) method was set up for the quantitative analyses. Signature peptides (20

264

µM) dissolved in 3% B/97% A were infused into the mass spectrometer at a flow rate of 10 µL/min

265

to characterize the product ions of each compound. The fragmentation was carried out using CID

266

mode. The MS/MS analyses were performed with a TSQ Quantum Triple Quadrupole (Thermo

267

Scientific) mass spectrometer fitted with an electrospray (ESI) interface operating in positive ion

268

mode and with the following source parameters: capillary temperature, 270 °C; spray voltage 4.5

269

kV; capillary voltage, 35 V; and tube lens voltage 211 V. The parameters influencing the transitions

270

were optimized as follows: argon gas pressure in the collision Q2, 1.0 mTorr; peak full width at

271

half-maximum (fwhm), m/z 0.70 at Q1 and Q3; scan width for all MRM channels, m/z 0.5; scan

272

time 0.675 s, skimmer offset 10V.

273

Linearity evaluation of standard peptides. Samples for linearity evaluation were obtained starting

274

from a stock solution containing all the peptides which was then diluted with a solvent composed of

275

3% B (0.1% HCOOH in CH3CN) and 97% A (0.1% HCOOH) to the following final concentrations:

276

10.000, 5.000, 2.500, 1.250, 1.000, 0.500, 0.025, 0.010 µM. Those standard solutions (10 µL each)

277

were injected into the LC-ESI-MS system and the analytes were separated by using the

278

chromatographic method above described. Three different MRM analytical methods were set-up:

279

parent ions were separately analyzed using three different methods, corresponding to the bovine

280

meal, pig meal, and fish meal signature peptide transitions respectively; 3 transitions for each parent

281

ion were included. Using a linear regression, seven linear curves were obtained from the areas

282

under the peak of the seven peptide signatures. Data processing was performed by Xcalibur 2.0

283

software.

284

Application of the method using a LC-ESI-5500 QTRAP ACS Paragon Plus Environment

Journal of Agricultural and Food Chemistry

285

Chromatographic and mass spectrometer conditions. The chromatographic separation was

286

performed performed on a reversed-phase 50 x 2.1 mm, i.d. 1.7 µm, 100 Å, Kinetex Core-Shell

287

Technology - C18 column (Phenomenex, Milan, Italy) with a Kinetex security-guard column

288

(Phenomenex, Milan, Italy), by using a Shimadzu Prominence HPLC system (Shimadzu S.R.L.

289

Italy, Milan, Italy) equipped with an autosampler kept at 8°C working at a constant flow rate (350

290

µL/min). 10 µL of standard solution was injected and peptides were eluted with a 15 min multistep

291

gradient of A (0.1% HCOOH) and B (0.1% HCOOH in CH3CN): 0-0.5 min, 3% B isocratic; 0.5-10

292

min, 3-45% B; 10-10.2 min, 45-95% B; 10.2-12 min, 95% B isocratic; and then 3 min 3% B

293

isocratic.

294

A multiple reaction monitoring (MRM) method was used. MS/MS analysis was performed with a

295

5500 QTRAP (Sciex Italy, Milan, Italy) mass spectrometer fitted with an turbo ion spray (TIS)

296

interface operating in positive ion mode and with the following source parameters: spray voltage

297

4.5 kV; source temperature (TEM) 450 °C; gas 1 and 2 at 50 and 55 psi, respectively; and curtain

298

gas at 30 psi. The parameters influencing the transitions were optimized as follows: nitrogen gas

299

pressure in the collision Q2, 10 mTorr; total scan time working in scheduled MRM was 0.4 s.

300

Beside the MRM acquisition mode, QTRAP instrument allows the full mass spectra registration to

301

confirm the amino acid sequence of each target peptide.

302

In order to test the enhanced instrument sensitivity in respect to the previous analysis (TSQ

303

Quantum Triple Quadrupole), standard peptide mixtures at three different concentrations (10.0nM,

304

1.0nM 0.1nM) were finally injected.

305 306

RESULTS AND DISCUSSION

307

Analytical strategy overview

308

To unequivocally identify the sources of bovine, pig and fish processed animal proteins (PAP) and

309

bovine milk proteins, the first step was a proteomic approach aimed at elucidating the proteome of

310

each source. Starting from the identified proteins and using a funnel based approach, a set of ACS Paragon Plus Environment

Page 12 of 38

Page 13 of 38

Journal of Agricultural and Food Chemistry

311

abundant and well characterized peptides with suitable physical-chemical properties (signature

312

peptides) and specific for each source were selected. An on-target LC-ESI-MS/MS method (MRM

313

mode) was then set-up using standard peptides and was then applied to selectively identify the PAP

314

source; this method was then successfully applied to verify the selectivity of the signature peptides

315

in different PAP sources and blank matrices (feedstuffs without PAP), to unequivocally identify

316

bovine PAP. The results for each step are reported in detail.

317

Proteomic approach

318

The proteomic approach consists of three steps: protein extraction, protein separation by SDS-

319

PAGE electrophoresis and digestion, protein sequencing by LC-ESI-MS.

320

Protein extraction - Several attempts were made to extract the maximum amount of protein from

321

PAP and the yield of protein extraction was evaluated by a densitometric analysis of the SDS-gel

322

electrophoresis patterns (data not shown). Several parameters were considered, such as the relative

323

percentage of SDS, temperature and time of extraction, and the protein precipitation agent. The

324

most suitable conditions in terms of protein extraction efficiency were obtained by treating PAP

325

samples with Laemmli sample buffer 2X at 85 °C (1200 rpm shaking) overnight to dissolve proteins

326

which were then isolated after acetone precipitation. It should be noted that such harsh conditions

327

for dissolving proteins are needed, due to the heat treatment used for PAP preparation, which

328

greatly denatures and covalently modifies the protein substrates, thus affecting their water

329

solubility. Acetone was selected as the protein precipitation agent, in part due to its ability to

330

dissolve lipids which are known to interfere with electrophoretic separation.

331

SDS-PAGE gel electrophoresis - Proteins were then separated by 1D SDS-PAGE electrophoresis

332

with the aim of splitting the proteins extracted from each source into 10 samples which were

333

individually injected into the LC-MS; this approach permits the reduction of the number of peptides

334

to be analyzed in each data dependent LC-MS run, thus increasing the rate of peptide identification;

335

gel electrophoresis was also used in order to efficiently remove SDS which would greatly affect ESI

336

ionization. The SDS-PAGE profiles in reducing conditions of proteins extracted from PAP derived ACS Paragon Plus Environment

Journal of Agricultural and Food Chemistry

337

from pig /fish/bovine are shown in Figure 1: all the lanes relative to PAP samples are characterized

338

by a quite smeared profile as was expected due to the rendering process for PAP preparation which

339

greatly affects protein integrity; however this does not represent a limiting aspect since here the

340

SDS-PAGE is not applied for an analytical purpose but to separate the entire proteome in 10

341

fractions; by contrast, the protein profile of the two batches of milk proteins shows more defined

342

bands. Figure 2 also shows the ten segments along each electrophoretic track which were cut to

343

enable in-gel protein digestion.

344

Protein identification by MS - Peptide sequence identification was carried out by LC-ESI-MS

345

analysis in data dependent scan mode and proteins were identified by using Proteome Discoverer

346

and setting high peptide confidence as filter (Peptide RANK 1). Only proteins with at least two

347

peptides assigned were considered. For each PAP source, a list of proteins was generated by

348

merging all the proteins identified in the 10 segments and deleting the redundancies by using the

349

merging tool. Starting from the complete list of proteins a step by step approach (here named funnel

350

based approach since based on a progressive exclusion of hits) was used in order to identify specific

351

and suitable proteins for each source. As an example, Figure 2A shows the funnel approach we used

352

for bovine PAP proteins. The initial list contains 179 unique gene products. We firstly excluded

353

proteins which are also contained in milk products and for this a list of proteins contained in milk

354

products was compiled by retrieving milk proteins from literature and from our database of

355

colostrum proteins.31,33 Proteins with a sequence coverage 20) and characterized by a low PSM value (