Nano TiO2 imparts amidoximated wool fibers with good antibacterial

Subscriber access provided by UNIV OF NEW ENGLAND ARMIDALE

Article

Nano TiO2 imparts amidoximated wool fibers with good antibacterial activity and adsorption capacity for uranium(VI) recovery Jun Wen, Qiaoyu Li, Hao Li, Min Chen, Sheng Hu, and Haiming Cheng Ind. Eng. Chem. Res., Just Accepted Manuscript • DOI: 10.1021/acs.iecr.7b04380 • Publication Date (Web): 29 Jan 2018 Downloaded from http://pubs.acs.org on January 30, 2018

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Industrial & Engineering Chemistry Research is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

Nano-TiO2 imparts amidoximated wool fibers with good antibacterial activity and adsorption capacity for uranium(VI) recovery

Jun Wen, † Qiaoyu Li, †,‡ Hao Li, † Min Chen, ‡,§ Sheng Hu, † Haiming Cheng *,‡,§

(† Institute of Nuclear Physics and Chemistry, China Academy of Engineering physics, Mianyang, China, 621900,; ‡

Key Laboratory of Leather Chemistry and Engineering of Ministry of Education,

Sichuan University, Chengdu, 610065; §

National Engineering Laboratory for Clean Technology of Leather Manufacture,

Sichuan University, Chengdu, 610065)

* Corresponding author, Haiming Cheng Tel: +86-28-8540-5839; Fax: +86-28-8540-5237; E-mail: [email protected] † Author Contributions J. Wen and Q. Y. Li made equal contributions to this work.

Abstract: Marine bacteria play a key role in marine ecosystems and are one of the main causes of biofouling. Biofouling of adsorbents that are used for uranium recovery usually results in a decrease in uranium recovery. A novel adsorbent with antibacterial activity for uranium recovery in bacterial environments was prepared in our study to address this concern. Amidoxime-functionalized wool fibers with nano-TiO2 particles 1

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

(Wool-AO@TiO2) was synthesized by radiation-induced graft polymerization combined with in-situ co-precipitation of nano-TiO2 particles onto the wool fibers. The presence of nano-TiO2 on the adsorbent was verified by scanning electron microscopy with energy-dispersive X-ray spectroscopy. The maximum uranium adsorption capacity of Wool-AO@TiO2, acquired from the Langmuir isotherm, was 113.12 mg/g. The introduced nano-TiO2 imparted excellent antibacterial activity to Wool-AO@TiO2. The inhibition of Staphylococcus aureus and Escherichia coli by Wool-AO@TiO2 was 95.2 and 90 %, respectively. The adsorption capacity was mostly unaffected in bacterial environments, even after four cycles of culturing with bacteria. These results suggest that the prepared Wool-AO@TiO2 adsorbent may promote the development of novel antifouling adsorbents for uranium recovery from seawater. Keywords: uranium(VI); adsorption; nano-TiO2; antibacterial activity; amidoxime; wool fiber.

2


Page 2 of 32

Page 3 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


1. Introduction Even though seawater has a uranium concentration of only 3.3 ppb, it is still considered a potential source of uranium because of the large amount it contains (~4.5 billion tons), which is approximately 1000 times as much as that found in mineral ores on land [1, 2]. According to the Organization for Economic Co-operation and Development, the total amount of uranium available from land mining could be exhausted in approximately one century with the current nuclear energy consumption rate [3]. Therefore, the development of processes for efficient uranium extraction from seawater plays an important role in the utilization of uranium and nuclear electricity industry. Scientists in many countries have been involved in the development of such techniques in recent decades [4-7]. Various materials have been developed as adsorbents for recovering uranium from seawater, such as polymeric fibers [8-10], biomaterials [11-13], inorganic materials [14-17], and nanomaterials [18, 19]. These studies focused mostly on how to enhance the adsorption capacity and selectivity for uranium. Biofouling due to marine bacteria, one of the essential factors that affect the adsorption of uranium from seawater, has been noted to reduce adsorption capacity. However, few studies have addressed this problem. Park et al. [20] revealed that the adsorption performance of amidoxime adsorbents decreased dramatically owing to biofouling when exposed to raw seawater in the presence of light. Although carrying out the recovery process below the photic zone would diminish this biofouling effect, the lower temperature at greater depth may result in poor adsorption capacity and rate. In addition, increasing the depth of operation will increase the technical difficulties and costs. For these reasons, the development of a uranium recovery adsorbent with

3



antibacterial activity is very important. To the best of our knowledge, no report on this exists so far. Titanium dioxide (TiO2) has been proposed as a potential adsorbent for uranium(VI) recovery [21-23]. Recently, nanoscale TiO2 (nano-TiO2) has received great attention because of its antibacterial activity, low cost, self-cleaning properties, good hydrophilicity, and stability [24]. Nano-TiO2 can be activated when irradiated with ultraviolet (UV) light in the presence of water vapor, which generates superoxide anions and hydroxyl radicals. The various highly active oxygen-containing radicals can oxidize organic compounds/cells, resulting in the death of microorganisms. Herein, we present a novel adsorbent comprising amidoxime-functionalized wool fibers with nano-TiO2 (Wool-AO@TiO2), synthesized by radiation-induced graft polymerization of acrylonitrile and methacrylic acid, combined with in-situ coprecipitation of nano-TiO2 particles onto the wool fibers; this material shows good adsorption capacity of uranium(VI) and excellent antibacterial activity in aqueous solutions. 2. Experimental 2.1. Materials Merino wool fibers were purchased from a local market. Acrylonitrile and methylacrylic acid were purchased from Sinopharm Chemical Reagent (Shanghai, China). Nano-TiO2 (size 25 nm) was purchased from Aladdin Chemicals (Shanghai, China), dispersed in an emulsion for irradiation grafting reactions. Hydroxylamine hydrochloride and sodium hydroxide were obtained from KeLong Chemicals (Chengdu China). A standard solution of uranium(VI) (1000 ppm) was supplied by the National Analysis and Testing Center (Beijing, China). Finally, a stock solution

4


Page 4 of 32

Page 5 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


(1000 ppm) of uranyl nitrate was prepared by dissolving uranyl nitrate hexahydrate into deionized water. All reagents were used as received without further treatment.

2.2. Preparation of adsorbents The

Wool-AO@TiO2

composites

were

synthesized

by

radiation-induced

polymerization in combination with an in-situ emulsion co-precipitation method as shown in Scheme 1. Briefly, 1.0 g of wool fibers, monomers (3 mL of acrylonitrile and 3 mL of methylacrylic acid), and nano-TiO2 particles (0–20 mg) were mixed in a transparent glass bottle and then sealed with foil. The mixtures were irradiated with an electron beam (electronic linear accelerator, VF-ProAcc-10/20, 10 MeV) at room temperature with a 200 kGy dose. The product was rinsed with acetone at 40 °C to remove the homopolymers and unreacted monomers, and then washed thoroughly with deionized water and dried. The obtained product was designated Wool-AN@TiO2. In order to obtain amidoxime groups, 0.5 g of Wool-AN@TiO2 was mixed with 50 mL of NH2OH·HCl solution (methanol:water = 1:1) containing 4.0 g NH2OH·HCl and neutralized to pH 7 with 0.2 M NaOH. This mixture was refluxed at 75 °C for 5 h. Subsequently, the wool fibers were thoroughly washed by methanol and dried, and the obtained adsorbent was designated Wool-AO@TiO2. Wool-AN and Wool-AO fibers without added nano-TiO2 were also prepared as controls following the same procedures as described above.

2.3. Characterization The Fourier transform infrared (FT-IR) spectra of pristine wool fibers, Wool-AN, and Wool-AO were collected on a Nicolet iS10 FT-IR spectrophotometer (Thermo 5



Scientific, USA) in KBr discs over a range from 4000 to 600 cm−1. The morphologies of the fibers were observed using a JSM-F7500 scanning electron microscope (SEM; Japan Electron Optical Laboratory Co., Ltd., Japan). The elemental composition of each adsorbent was determined by a 51-XMX0019 X-Max energy-dispersive X-ray spectroscopy (EDXS) analyzer (Oxford Instruments, UK). Thermogravimetric analysis (TGA) of the samples was carried out on a TG 209 F (Netzsch, Germany) from 20 to 800 °C with a heating rate of 10 °C/min. The cell was purged with air at 60 mL/min during heating. The nitrogen adsorption isotherms of the samples were detected by a Tristar 3000 surface area and porosity analyzer (Micromeritics, USA) at liquid nitrogen temperature (77 K). The surface area of each sample was calculated using the Brunauer-Emmett-Teller (BET) equation. All tests were run in triplicate.

2.4. Adsorption experiments Uranium sorption experiments were performed in simulated seawater (consisting of UO2(NO3)2·6H2O (~50 ppm), NaHCO3 (~193 ppm) and NaCl (~25,600 ppm) in deionized water, with a pH of 8.0 ± 0.2). Briefly, 20 mg of the adsorbent and 20 mL of a uranium aqueous solution were added to a 50-mL plastic flask and shaken using a thermostat shaker (WS-300R, Wiggens) at 100 rpm for 24 h at 25 °C. The concentration of uranium was determined with inductively coupled plasma optical emission spectroscopy (ICP-OES). The amount of uranium adsorbed at equilibrium was calculated by Eq. 1: ‫ݍ‬௘ ൌ

ሺ஼బ ି஼೐ ሻ௏ ௠

（1）

where qe (mg U/g) is the equilibrium sorption capacity, v (mL) the volume of solution, m (g) the adsorbent weight, and C0 (mg/L) and Ce (mg/L) the concentrations of uranium at the initial and equilibrium states, respectively. 6


Page 6 of 32

Page 7 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


The effect of pH on the adsorption was studied by varying the pH values from 3 to 9 by slow adjustments with 0.1 M K2CO3 and 0.1 M HNO3. All adsorption experiments were conducted for 24 h at 25 ºC with an initial metal ion concentration of 50 mg/L. The isotherm studies were conducted at pH 8.0 with initial uranium concentrations varying from 10 to 500 ppm.

2.5. Antibacterial activity analysis To determine the antibacterial properties of the adsorbents, the dilution plate counting method was performed according to Chinese standard GB/T 20944. Briefly, sterile plate count agar (PCA) plates were prepared by pouring sterilized media onto the sterile plates under aseptic conditions. Then, 10 mg of sample was cultured with 20 mL of 30 mM phosphate buffer saline (PBS, 0.15 M NaCl, pH 7.4) containing bacteria species at a concentration of ~105 CFU/mL and lysogeny broth (LB) medium. Afterwards, the mixture was shaken at 150 rpm for 18 h at 24 °C in a water bath exposed to visible light. Subsequently, 0.2 mL of the supernatant was spread on PCA using a 10-fold dilution method. The number of colonies was counted after incubating at 37 °C for 24 h in a constant temperature incubator. The amount of inhibition by each sample was calculated by Eq. 2: ‫ܫ‬ൌ

ௐ೟ ିொ೟ ௐ೟

×100%

（2）

where I (%) is the inhibition rate, and Wt and Qt are the amounts of colonies of the test and control sample, respectively. Gram-negative Escherichia coli (E. coli) and Grampositive Staphylococcus aureus (S. aureus) were selected as the test species, and pristine wool fiber was used as the control sample.

3. Results and discussion 7



3.1. Characterization The FT-IR spectra of pristine wool, Wool-AN@TiO2, and Wool-AO@TiO2 are shown in Figure 1. The spectrum of pristine wool fibers shows typical peaks at 1632.8 cm−1 for C=O (amide I), 1545.7 cm−1 for N-H (amide II), and 1387.7 cm−1 for C-N (amide III) [25]. After grafting, in Wool-AN@TiO2, new bands can be observed at 2246.1 and 1735.6 cm−1 (Figure 1a); these can be attributed to nitrile and carboxyl groups, respectively, suggesting that acrylonitrile and methylacrylic acid were successfully grafted onto the wool fibers. In the spectrum for Wool-AO@TiO2, the disappearance of nitrile stretching bands and appearance of signatures for N-O (927.7 cm−1) and C=O (1646.6 cm−1) can clearly be observed after amidoximation [12], which indicates that the nitrile groups were converted to amidoxime groups. SEM images of pristine wool, Wool-AO, and Wool-AO@TiO2 are shown in Figure 2. It can clearly be observed that grafting and amidoximation damaged or caused damage to the scale layer of the pristine wool fibers (Figure 2b). Moreover, many nanoparticles appeared (sizes ranging from 20–40 nm to 300–500 nm) on the surface of Wool-AO@TiO2 (Figure 2d), illustrating that nano-TiO2 had successfully been affixed onto the wool fibers by in-situ co-precipitation. The SEM-EDXS profiles (Figure 3b) show the presence of elemental Ti on Wool-AO@TiO2, which further indicates that nano-TiO2 particles were successfully loaded onto the wool fibers. TGA of pristine wool, Wool-AO, and Wool-AO@TiO2 was conducted from 20 to 800 °C at a heating rate of 10 °C/min (see Figure S2 in the supporting information). The results are shown in Table 1, in which IDT means the initial decomposition temperature, FDT means the final decomposition temperature, and Tp means peak derivative temperature. Wool-AO@TiO2 exhibited the lowest Tp (300.1 °C) compared to Wool-AO (313.3 °C) and pristine wool (319.9 °C); however, Wool-AO@TiO2 8


Page 8 of 32

Page 9 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


exhibited the highest residual mass (26.1 %) among the three samples. These differences can likely be explained by both the grafting and amidoximation processes and the loading of nano-TiO2 particles; the SEM images in Figure 2 show evidence of damage to the wool fibers during grafting and amidoximation, which causes a decrease in thermal stability.

3.2．Adsorption experiments 3.2.1. Effect of dosage of nano-TiO2 particles on adsorption capacity The influence of the amount of TiO2 on Wool-AO@TiO2 on the sorption of uranium(VI) was investigated by varying the TiO2 dosage deposited on the wool fibers; adsorption experiments were performed for 24 h at pH 8.0 and 25 ºC with an initial metal ion concentration of 50 mg/L. As shown in Figure 4, the adsorption of uranium by Wool-AO@TiO2 increased as the amount of nano-TiO2 particles was increased from 0 to 1.5 %, with a maximum adsorption capacity of 72.3 mg/g. This was possible since TiO2 has good uranium adsorption properties. Moreover, the higher specific surface area of Wool-AO@TiO2 than Wool-AO may play a role in adsorption as well. As shown in Table 1, the specific surface area of Wool-AO@TiO2 (Dose of TiO2 of 1.5%) was 3.83 m2/g, notably higher than that of Wool-AO (2.51 m2/g). However, when further increasing the concentration of TiO2 to 2.0 %, the adsorption capacity of uranium decreased to 57.1 mg/g. The reason may be agglomeration of nano-TiO2 particles, which is much more probable with increasing TiO2 dosages; this agglomeration may have resulted in TiO2 particles that are larger than nanoparticle size [26]. Since the metal ion adsorption capacity of nano-TiO2 particles depends on their size [27-29], this may have caused the decrease in adsorption capacity at the nano-TiO2 concentration of 2.0 %. 9



3.2.2. Effect of initial pH on adsorption The initial pH of the solution plays a key role in the adsorption capacity, since pH affects both the speciation of uranium in aqueous solutions and the activity of the binding groups on the adsorbents. The effect of pH on adsorption of uranium(VI) onto Wool-AO@TiO2 was investigated by varying the pH from 3.0 to 9.0. The results are shown in Figure 5. The adsorbed amount of uranium(VI) on Wool-AO increased from 6.52 mg/g to 31.1 mg/g as the pH was increased from 3.0 to 6.0, but then slightly decreased at higher pH values, staying relatively constant. For Wool-AO@TiO2, the amount of adsorbed uranium increased rapidly between pH 3.0 and 6.0, from 29.8 to 67.5 mg/g, and then slowly further increased until reaching 74.1 mg/g at the pH of 9.0. At the same pH, uranium uptake by Wool-AO@ TiO2 was therefore higher than by Wool-AO. When the initial pH was lower than 3.0, the adsorbed amount for uranium recovery by Wool-AO was only 6.52 mg/g. The latter could be explained by UO22+ being the predominant species of uranyl when the pH is below 3 [30]; at the same time, most amidoxide groups on Wool-AO are protonated, providing few binding sites for the cationic uranium [31]. When increasing the initial pH, the protonated amidoxime groups gradually deprotonate, while UO22+ hydrolyzes to form less positively-charged species such as UO2(OH)2+ and UO2NO3+. As a result, repulsion decreases and uranyl species can more easily coordinate with amidoxime groups [32], leading to enhanced adsorption. When the pH is higher than 6.0, UO22+ undergoes further hydrolysis, forming some species that are neutral, ,negatively charged, or precipitate. The amidoxime groups easily react with OH- to form a negatively-charged substance, leading to another electrostatic repulsion that is not beneficial to the adsorption of 10


Page 10 of 32

Page 11 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


uranium [33]. As a consequence, the optimal pH of Wool-AO is at 6.0. Since nanoTiO2 has a higher pHZCP of 6.0–7.0 [34,35] than amidoxime groups (pHZCP 4.3) [27], the adsorption capacity of Wool-AO@TiO2 is more stable at a higher pH value, with an optimum pH of 7.0–8.0. To ensure that the pH of the experimental system is consistent with that of seawater, all following experiments were performed at pH 8.0. The effect of contact time, adsorption kinetics, and equilibrium studies are described in detail in the supplemental information. The results show that the equilibrium times of Wool-AO and Wool-AO@TiO2 were about 7 and 10 h, respectively (Figure S3). The Langmuir model was suitable to describe the adsorption process of uranium for both Wool-AO and Wool-AO@TiO2, implying a monolayer coverage of uranium onto both materials. The maximum uranium adsorption capacity (qm) of WoolAO@TiO2, acquired from Langmuir isotherms, was 113.12 mg/g, which is higher than that of Wool-AO (49.6 mg/g) (Table S1). These results indicate that the addition of nano-TiO2 on Wool-AO improved its uranium(VI) adsorption capacity.

3.3. Antibacterial activity Many reports have been concerned with improving adsorption capacities from aqueous solutions, especially from seawater. However, biofouling is a critical factor that may invalidate these previous efforts. Therefore, the antibacterial activity of adsorbents should be of concern as well. Herein, Gram-negative E. coli and Grampositive S. aureus were selected to investigate the antibacterial activity of WoolAO@TiO2 in aqueous solutions, as those are the most common models for antibacterial studies [36].

3.3.1. Effect of the dosage of TiO2 nanoparticles 11



The effect of the amount of TiO2 on Wool-AO@TiO2 on its antibacterial activity was investigated, with results shown in Figure 6 (all data in triplicate). This shows that the use of TiO2 nanoparticles improved the antibacterial activity of Wool-AO; within the experimental range, the extent of E. coli inhibition by Wool-AO@TiO2 increased with increasing dosage of TiO2 nanoparticles, with the inhibition reaching a maximum of 90 % at a TiO2 dosage of 1.5–2.0 %. Similarly, the S. aureus inhibition increased sharply when the dosage of TiO2 nanoparticles was less than 1.0 %, then increased slower ay higher dosages, ultimately reaching a maximum of 95.2 % at a 1.5–2.0 % TiO2 dose. According to these results, Wool-AO@TiO2 exhibited greater inhibition of S. aureus than of E. coli, which may be due to the different bacterial cell structures [37]. It is known that Gram-negative bacteria (e.g., E. coli) have a triple-layer cell wall with an inner membrane, a thin peptidoglycan layer, and an outer membrane, whereas Gram-positive bacteria (e.g., S. aureus) have a thicker peptidoglycan layer and no outer membrane. Similar results have been reported in several other studies [36, 38-40]. Photographs in Figure 7 depict the antibacterial activity of Wool-AO and Wool-AO@TiO2 against E. coli.

3.3.2. Uranium(VI) adsorption in bacterial environments To investigate the adsorption behavior of Wool-AO@TiO2 in bacterial environments, adsorption experiments at 25 °C were also performed in 30 mM PBS buffer (pH 8.0) with 105 CFU/mL bacteria and an initial uranium(VI) concentration of 50 ppm. The results, shown in Figure 8 (all data in triplicate), indicate that the adsorption processes reached equilibrium states earlier (after 4–6 h) and yielded higher uranium adsorption capacities in bacterial environments (87.5 mg/g with E. coli, 104.1 mg/g with S. aureus) than in environments without bacteria (7–10 h and 72.3 mg/g, see also 12


Page 12 of 32

Page 13 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


supporting information Figure S3). This may be explained by phosphate in the bacterial system possibly being beneficial to uranium adsorption (supporting information Figure S6) [41-43]. Furthermore, the uranium(VI) adsorption capacity of Wool-AO@TiO2 in the presence of S. aureus was greater than in the presence of E. coli, which implies that the influence of S. aureus on adsorption is easier to avoid.

3.3.3. Cyclic antibacterial testing To evaluate long-term bacterial resistance, Wool-AO@TiO2 and bacterial solution were cultured continuously for 4 cycles. The antibacterial tests were performed as described above. At the end of each culture cycle, the solution was removed by centrifugation and the adsorption capacity measured by ICP-OES. The WoolAO@TiO2 with adsorbed uranium(VI) was then placed in a 0.1 M Na2CO3 solution (100 mL) for regeneration at 25 °C for 24 h. The regenerated adsorbent was subsequently placed in a newly activated bacterial solution with 50 ppm uranium(VI) for another culture run. The results, shown in Figure 9 (each data point in triplicate), indicate that the antibacterial activity of Wool-AO@TiO2 decreases slightly with an increasing number of cycles. After 4 cycles, E. coli and S. aureus inhibitions still remained at relatively high levels of 88.4 and 89 %, respectively, of the initial inhibition amounts. The adsorption capacity of the material in each bacterial culture is listed in Table 2. Wool-AO@TiO2 still exhibited good adsorption capability for uranium(VI) even after 4 cycles, indicating the good reusability properties of WoolAO@TiO2.

4. Conclusions

13



Page 14 of 32

In summary, a novel adsorbent comprising amidoxime-functionalized wool fibers with

nano-TiO2

(Wool-AO@TiO2)

was

prepared

by

radiation-induced

copolymerization, and its adsorption properties and antibacterial activity were investigated. Wool-AO@TiO2 exhibited pH-dependent uranium(VI) adsorption capacity with good adsorption efficiency in the pH range from 6.0 to 9.0. The adsorption process followed Langmuir isotherm adsorption model and pseudo-second order kinetics. The maximum uranium adsorption capacity of Wool-AO@TiO2, acquired from the Langmuir isotherm, was 113.12 mg/g. The increase in specific surface area of Wool-AO@TiO2 after TiO2 functionalization may have led to an enhancement of adsorption capacity. It should also be noted that Wool-AO@TiO2 showed good antibacterial activity, effectively inhibiting growth of the model bacteria S. aureus and E. coli with 95.2 and 90 %, respectively. At the same time, the adsorption of uranium(VI) in bacterial environments was not negatively affected. Even after a 4-cycle culture in the presence of bacteria, the adsorption capacity did not significantly decrease. Therefore, the synthesized antibacterial adsorbent may potentially be applicable for the extraction of uranium from seawater and promote the development of new types of efficient adsorption materials.

Acknowledgement The authors are grateful for the financial support of the Radiochemistry 909 Project in the China Academy of Engineering Physics, the Key Research Program of Sichuan Province of China (2017GZ0268, 2017TD0010).

Appendix A. Supplementary data

14


Page 15 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Detailed experimental procedures and compound characterization. Supplementary data related to this article can be found in the online version.

References [1] Kim, J.; Tsouris, C.; Mayes, R. T.; Oyola, V.; Saito, T.; Janke, C. J.; Dai, S.; Schneider, E.; Sachde, D. Recovery of uranium from seawater: a review of current status and future research needs. Sep. Sci. Technol. 2013, 48, 367-387. [2] Uranium 2014: Resources, Production and Demand; Technical Report NEA 7209; OECD Nuclear Energy Agency: Paris, France, 2014. [3] Brown, S.; Chatterjee, S.; Li, M. J.; Yue, Y. F.; Tsouris, C.; Janke, C. J.; Saito, T.; Dai, S. Uranium Adsorbent Fibers Prepared by Atom-Transfer Radical Polymerization from Chlorinated Polypropylene and Polyethylene Trunk Fibers. Ind. Eng. Chem. Res. 2016, 55, 4130-4138. [4] Tamada, M. Technology of uranium recovery from seawater. J. Jpn. Inst. Energy. 2009, 88, 249-253. [5] Nuclear Energy Research and Development Roadmap: Report to Congress; U.S. Department of Energy: Washington, D.C, 2010. [6] Choi, S. H.; Nho, Y.C. Adsorption of UO22+ by polyethylene adsorbents with amidoxime, carboxyl, and amidoxime/carboxyl group. Radiat. Phys. Chem. 2000, 57, 187-193. [7] Kelmers, A. D. Status of technology for the recovery of uranium from seawater. Sep. Sci. Technol. 1981, 16, 1019-1035. [8] Kim, J. S.; Tsouris, C.; Oyola, Y.; Janke, C. J.; Mayes, R. T.; Dai, S.; Gill, G.; Kuo, L. J.; Wood, J., Choe, K. Y.; Schneider, E.; Lindner, H. Uptake of uranium from seawater by amidoxime-based polymeric adsorbent: field experiments, modeling, and updated economic assessment. Ind. Eng. Chem. Res. 2014, 53, 6076-6083.

15



[9] Schenk, H. J.; Astheimer, L.; Witte, E. G.; Schwochau, K. Development of sorbers for the recovery of uranium from seawater .1. assessment of key parameters and screening studies of sorber materials. Sep. Sci. Technol. 1982, 17, 1293-1308. [10] Brown, S.; Yue, Y. F.; Kuo, L. J.; Mehio, N.; Li. M. J.; Gill, G.; Tsouris, C.; Mayes, R. T.; Saito, T.; Dai, S. Uranium Adsorbent Fibers Prepared by Atom-Transfer Radical Polymerization (ATRP) from Poly(vinyl chloride)-co-chlorinated Poly(vinyl chloride) (PVCco-CPVC) Fiber. Ind. Eng. Chem. Res. 2016, 55, 4139-4148. [11] Anirudhan, T. S.; Deepa, J. R.; Binusreejayan. Synthesis and characterization of multicarboxyl-functionalized nanocellulose/nanobentonite composite for the adsorption of uranium(VI) from aqueous solutions: kinetic and equilibrium profiles. Chem. Eng. J. 2015, 271, 390-400. [12] Yin, Z. L.; Xiong, J.; Chen, M.; Hu, S.; Cheng, H. M. Recovery of uranium(VI) from aqueous solution by amidoxime functionalized wool fibers. J. Radioanal. Nucl. Chem. 2016, 307, 1471-1479. [13] Hazer, O.; Kartal, S. Use of amidoximated hydrogel for removal and recovery of U(VI) ion from water samples. Talanta. 2010, 82, 1974-1979. [14] Guerra, D. L.; Leidens, V. L.; Viana, R. R.; Airoldi, C. Amazon kaolinite functionalized with diethylenetriamine moieties for U(VI) removal: thermodynamic of cation-basic interactions. J. Hazard. Mater. 2010, 180, 683-692. [15] Zakutevskii, O. I.; Psareva, T. S.; Strelko, V. V.; Kartel’, N. T. Sorption of U(VI) from aqueous solutions with carbon sorbents. Radiochem. 2007, 49, 67-71. [16] Ding, C.; Cheng, W.; Nie, X.; Yi, F. Synergistic mechanism of U(VI) sequestration by magnetite-graphene oxide composites: Evidence from spectroscopic and theoretical calculation. Chem. Eng. J. 2017, 324, 113-121. [17] Guo, Z. J., Yan, Z. Y.; Tao, Z. Y. Sorption of uranyl ions on TiO2: effects of contacttime, ionic strength, concentration and humic substance. J. Radioanal. Nucl. Chem. 2004, 261, 157162. 16


Page 16 of 32

Page 17 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


[18] Tan, L.; Zhang, X.; Liu, Q.; Jing, X.; Liu, J.; Song, D.; Hu, S.; Liu, L.; Wang, J. Synthesis of Fe3O4 @TiO2, core–shell magnetic composites for highly efficient sorption of uranium(VI). Colloid. Surface A. 2015, 469, 279-286. [19] Khajeh, M.; Jahanbin, E. Application of cuckoo optimization algorithm–artificial neural network method of zinc oxide nanoparticles–chitosan for extraction of uranium from water samples. Chemometr. Intell. Lab. 2014, 135, 70-75. [20] Park, J.; Gill, G. A.; Strivens, J. E.; Kuo, L. J.; Jeters, R. T.; Avila, A.; Wood, J. R.; Schlafer, N. J.; Janke, C. J.; Miller, E. A.; Thomas, M.; Addleman, R. S.; Bonheyo, G. T. Effect of biofouling on the performance of amidoxime-based polymeric uranium adsorbents. Ind. Eng. Chem. Res. 2016, 55, 4328-4338. [21] Davies, R.V.; Kennedy, J.; McIlroy, R.W.; Spence, R.; Hill, K.M. Extraction of uranium from seawater. Nature. 1964, 203, 1110-1115. [22] Wazne, M.; Meng, X.; Korfiatis, G. P.; Christodoulatos, C. Carbonate effects on hexavalent uranium removal from water by nanocrystalline titanium dioxide. J. Hazard. Mater. 2006, 136, 47-52. [23] Jaffrezic-Renault, N.; Poirier-Andrade, H.; Trang, D.H. Models for the adsorption of uranium on titanium dioxide. J. Chromatogr. A. 1980, 201, 187-192. [24] Liou, J. W.; Chang, H. H. Bactericidal effects and mechanisms of visible lightresponsive titanium dioxide photocatalysts on pathogenic bacteria, Arch. Immunol. Ther. Exp. 2012, 60, 267-275. [25] Monier, M.; Nawar, N.; Abdel-Latif, D.A. Preparation and characterization of chelating fibers based on natural wool for removal of Hg(II), Cu(II) and Co(II) metal ions from aqueous solutions. Journal of Hazardous Materials. 2010, 184, 118-125. [26] Comarmond, M. J.; Payne, T. E.; Harrison, J. J.; Thiruvoth, S.; Wong, H. K.; Aughterson, R. D.; Lumpkin, G. R.; Müller, K.; Foerstendorf, H. Uranium sorption on various forms of titanium dioxide–influence of surface area, surface charge, and impurities. Environ. Sci. Technol. 2011, 45, 5536-5542. 17



[27] Li, W. P.; Han, X. Y.; Wang, X. Y.; Wang, W. X.; Hu, H.; Tan, T. S.; Wu, W. S.; Zhang, H. X. Recovery of uranyl from aqueous solutions using amidoximated polyacrylonitrile /exfoliated Na-montmorillonite composite. Chem. Eng. J. 2015, 279, 735-746. [28] Sawai, J.; Igarashi, H.; Hashimoto, A. Effect of particle size and heating temperature of ceramic powders on antibacterial activity of their slurries. J. Chem. Eng. Jpn. 1996, 29, 251256. [29] Swetha, S.; Singh, M. K.; Minchitha, K. U.; Balakrishna, R. G. Elucidation of cell killing mechanism by comparative analysis of photoreactions on different types of bacteria. Photochem. Photobiol. 2012, 88, 414-422. [30] Camacho, L. M.; Deng, S.; Parra, R. R. Uranium removal from groundwater by natural clinoptilolite zeolite: effects of pH and initial feed concentration. J. Hazard. Mater. 2010, 175, 393-398. [31] Schierz, A.; Zanker, H. Aqueous suspensions of carbon nanotubes: surface oxidation, colloidal stability and uranium sorption. Environ. Pollut. 2009, 157, 1088-1094. [32] Abney, C. W.; Mayes, R. T.; Piechowicz, M.; Lin, Z.; Bryantsev, V. S.; Veith, G. M.; Dai, S.; Lin, W. XAFS investigation of polyamidoxime-bound uranyl contests the paradigm from small molecule studies. Energy Environ. Sci. 2016, 9, 448-453. [33] Bai, J.; Yin, X.; Zhu, Y.; Fan, F.; Wu, X.; Tian, W.; Tan, C.; Zhang, X.; Wang, Y.; Cao, S.; Fan, F.; Qin, A.; Guo, J. Selective uranium sorption from salt lake brines by amidoximated Saccharomyces cerevisiae. Chem. Eng. J. 2016, 283, 889-895. [34] Gou, Z.; Niu, L.; Tao, Z. Sorption of Th(IV) ions onto TiO2: Effects of contact time, ionic strength, thorium concentration andphosphate. J. Radioanal. Nucl. Chem. 2005, 266, 333-338. [35] M. Olsson, M.; A. M. Jakobsson, A. M.; Albinsson, Y. Sorption of Pu(VI) onto TiO2. J. Colloid Interf. Sci. 2003, 266, 269-275.

18


Page 18 of 32

Page 19 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


[36] Pal, A.; Pehkonen, S. O.; Yu, L. E.; Ray, M. B. Photocatalytic inactivation of Grampositive and Gram-negative bacteria using fluorescent light. J. Photochem. Photobiol. A Chem. 2007, 186, 335-341. [37] Skorb, E. V.; L. I. Antonouskaya, L. I.; Belyasova, N. A.; Shchukin, D. G.; Möhwald, H.; Sviridov, D. V. Antibacterial activity of thin-film photocatalysts based on metal-modified TiO2 and TiO2: In2O3 nanocomposite. Appl. Catal. B Environ. 2008, 84, 94-99. [38] Swetha, S.; Singh, M.K.; Minchitha, K.U.; Balakrishna, R. G. Elucidation of cell killing mechanism by comparative analysis of photoreactions on different types of bacteria. Photochem. Photobiol. 2012, 88, 414-422. [39] Yadav, H. M.; Otari, S.V.; Koli, V.B.; Mali, S. S.; Hong, C. K.; Pawar, S. H.; Delekar, S.D. Preparation and characterization of copper-doped anatase TiO2 nanoparticles with visible light photocatalytic antibacterial activity. J. Photochem. Photobiol. A Chem. 2014, 280, 32-38. [40] Yadav, H. M.; Kolekar, T.V.; Pawar, S. H.; Kim, J. S. Enhanced photocatalytic inactivation of bacteria on Fe-containing TiO2 nanoparticles under fluorescent light. J. Mater. Sci. Mater. Med. 2016, 27, 57. [41] Guo, Z.; Guo, F.; Tao, Z. Effects of phosphate and ionic strength upon uranium(VI) sorption onto alumina as a function of pH. Radiochim. Acta. 2006, 94, 223-228. [42] Comarmond, M. J.; Steudtner, R.; Stockmann, M.; Heim, K.; Müller, K.; Brendler, V.; Payne, T. E.; Foerstendorf, H. The sorption processes of U(VI) onto SiO2 in the presence of phosphate: from binary surface species to precipitation. Environ. Sci. Technol. 2016, 50, 11610-11618. [43] Zhang, H.; Tang, Q.; Tao. Z. Effects of phosphate and Cr3+ on the sorption and transport of uranium(VI) on a silica column. J. Radioanal. Nucl. Chem. 2009, 279, 317-323.

19



Figure captions Scheme 1. synthesis of amidoxime-functionalized wool fibers with nano-TiO2 (WoolAO@TiO2). Figure 1. Fourier transform infrared (FT-IR) spectra of wool, wool fibers with nano-TiO2 without amidoxime groups (Wool-AN@TiO2), and Wool-AO@TiO2. Figure 2. Scanning electron microscope (SEM) profiles: (a) pristine wool; (b) amidoximefunctionalized wool fibers without TiO2 (Wool-AO); (c) and (d) Wool-AO-TiO2. Figure 3. SEM-energy-dispersive X-ray spectroscopy (EDXS) profiles: (a) wool and (b) Wool-AO@TiO2. Figure 4. Effect of dosage of TiO2 on adsorption. Conditions: pH 8.0, temperature (T) 25 °C, initial uranium(VI) concentration (C0) 50 ppm, and time = 24 h. Figure 5. Effect of initial pH on adsorption. Conditions: T = 25 °C, C0 = 50 ppm, time = 24 h. Figure 6. Effect of dosage of TiO2 on antibacterial activity. Figure 7. Antibacterial activity of adsorbents against E. coli: (a) control; (b) Wool-AO; and (c) Wool-AO@TiO2 with 1.5 % TiO2. Figure 8. Adsorption of uranium in bacterial environments. Conditions: T = 25 °C, C0 = 50 ppm, and 105 CFU/mL bacteria in 30 mM PBS buffer (pH 8.0). Figure 9. Antibacterial testing over 4 cycles.

20


Page 20 of 32

Page 21 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Tables

Table 1. Thermogravimetric analysis (TGA) parameters and specific surface areas of wool, WoolAO, and Wool-AO@TiO2. IDT: initial decomposition temperature; FDT: final decomposition temperature. Tp: peak derivative temperature.

Sample

TGA

Specific area

Tp (°C)

(m2/g) IDT (°C)

FDT (°C)

Residual mass (%)

Pristine Wool

2.35

266.5

383.8

17.8

319.9

Wool-AO

2.51

262.9

380.0

13.4

313.3

Wool-AO@TiO2

3.83

264.5

361.7

26.1

300.1

Table 2. Adsorption after cyclic antibacterial testing. Wool-AO@TiO2

Adsorption after culture with E. coli

Adsorption after culture with S.

(mg/g)

aureus (mg/g)

Cycle 1

87.5

104.1

Cycle 2

86.4

102.6

Cycle 3

85.7

100.4

Cycle 4

83.4

97.3

21



For Table of Contents Only

22


Page 22 of 32

Page 23 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46


Scheme 1

electron beam

+

+

methacrylic acid acrylonitrile

Wool fibers nano TiO2

n

NH2OH

C N

Wool-AN@TiO2


H2N

n

N OH

Wool-AO@TiO2

Industrial & Engineering Chemistry Research 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46

Figure 1


Page 24 of 32

Page 25 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46


Figure 2



Page 26 of 32

Figure 3

A


B

Page 27 of 32

Figure 4 80 70 60

qe(mg/g)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46


50 40 30 0.0

0.5

1.0

1.5

Addition of oxide (%)


2.0


Figure 5

Wool-AO

75

Wool-AO@TiO2

60

q e(mg/g )

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46

Page 28 of 32

45 30 15 0

3

4

5

6

pH


7

8

9

Page 29 of 32

Figure 6

E. coli S. aureus

95 90

Inhibition rate (%)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46


85 80 75 70 0.0

0.5

1.0

Addition of TiO2 (%)


1.5

2.0


Figure 7


Page 30 of 32

Page 31 of 32

Figure 8

100 80

qe (mg/g)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46


60

E. coli S. aureus

40 20 0 0

5

10

Time (h)

15


20

25


Figure 9

100

E. coli S. aureus

90

Inhibition rate (%)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46

Page 32 of 32

80

70

60

50

0

1

2

Cycle times

3


4

Nano TiO2 imparts amidoximated wool fibers with good antibacterial

Recommend Documents