Subscriber access provided by READING UNIV
Article
Quantification of Humic Substances in Natural Water Using Nitrogen-Doped Carbon Dots Yan-Fang Guan, Bao-Cheng Huang, Chen Qian, and Han-Qing Yu Environ. Sci. Technol., Just Accepted Manuscript • DOI: 10.1021/acs.est.7b04430 • Publication Date (Web): 17 Nov 2017 Downloaded from http://pubs.acs.org on November 18, 2017
Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.
Environmental Science & Technology is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.
Page 1 of 30
Environmental Science & Technology
Quantification of Humic Substances in Natural Water Using Nitrogen-Doped Carbon Dots
Yan-Fang Guan†, Bao-Cheng Huang†, Chen Qian, Han-Qing Yu* CAS Key Laboratory of Urban Pollutant Conversion, Department of Chemistry, University of Science & Technology of China, Hefei 230026, China
1
ACS Paragon Plus Environment
Environmental Science & Technology
1
Dissolved organic matter (DOM) is ubiquitous in aqueous environments and plays a
2
significant role in pollutant mitigation, transformation and organic geochemical
3
circulation. DOM is also capable of forming carcinogenic by-products in the
4
disinfection treatment processes of drinking water. Thus, efficient methods for DOM
5
quantification are highly desired. In this work, a novel sensor for rapid and selective
6
detection of humic substances (HS), a key component of DOM, based on fluorescence
7
quenching of nitrogen-doped carbon quantum dots was developed. The experimental
8
results show that the HS detection range could be broadened to 100 mg/L with a
9
detection limit of 0.2 mg/L. Moreover, the detection was effective within a wide pH
10
range of 3.0 to 12.0, and the interferences of ions on the HS measurement were
11
negligible. A good detection result for real surface water samples further validated the
12
feasibility of the developed detection method. Furthermore, a non-radiation electron
13
transfer mechanism for quenching the nitrogen-doped carbon-dots fluorescence by HS
14
was elucidated. In addition, we prepared a test paper and proved its effectiveness. This
15
work provides a new efficient method for the HS quantification than the frequently
16
used modified Lowry method in terms of sensitivity and detection range.
2
ACS Paragon Plus Environment
Page 2 of 30
Page 3 of 30
Environmental Science & Technology
17
INTRODUCTION
18 19
Humic substances (HS) are prevalent in aqueous environment and the main
20
component of dissolved organic matter (DOM) with a typical concentration range of
21
0.2-20 mg/L in surface water.1 HS can affect the dissolution, mitigation,
22
transformation and bioavailability of heavy metals2-5 and are involved in the microbial
23
electron transfer processes.6 Moreover, they are able to form carcinogenic by-products
24
(e.g., trihalomethanes) in the disinfection treatment process of drinking water.7-9
25
Therefore, it is of great importance to determine the HS concentration in natural water
26
and further understand their potential environmental effects. The development of a
27
sensitive HS quantification method with a high reliability and stability is prerequisite
28
for achieving this aim.
29
Several methods such as elemental analysis, electrochemical analysis,
30
chemiluminescence, UV-Vis absorption spectroscopy, and high performance size
31
exclusion chromatography have been developed for HS quantification.10-16 However,
32
each of these detection methods has its own drawbacks. Elemental analysis, e.g.,
33
nuclear magnetic resonance spectroscopy and Fourier transform infrared spectroscopy
34
(FTIR), is unsuitable for quantitative analysis and requires a large amount of sample
35
(usually more than 100 mg is needed for nuclear magnetic resonance).10,11 Although
36
cathodic stripping voltammetry is effective for HS measurements,12 it can be easily
37
interfered by metal ions such as Fe3+ and Ca2+, leading to inaccurate results.
38
Chemiluminescence can be accomplished with the help of glycine and oxidants
39
(1,3-dibromine-5,5-dimethylhydantion). Unfortunately, it leads to the formation of
40
bromides and hypobromites, which are harmful to the environment.13,14 UV-vis
41
spectroscopy method has been widely used to characterize the HS content in natural 3
ACS Paragon Plus Environment
Environmental Science & Technology
42
waters. However, it shows no selectivity to HS and other aromatic compounds in
43
water might cause interferences.15 Other methods such as dissolved organic carbon
44
quantification are unable to distinguish HS from other organics either. In comparison,
45
high performance size exclusion chromatography is able to isolate and detect the HS
46
from other organics, but it is time consuming and costly columns are needed.16 In fact,
47
HS contain many chromophoric (light absorbance) and fluorophoric (light emission)
48
moieties because of their aromatic chromophores and π bonding, which could be
49
characterized by fluorescence.17 However, fluorescence measurement could be
50
interfered by instrumental state, sample themselves and data analysing.18 Furthermore,
51
fluorescence will be self-quenched once DOM is present at a high concentration.
52
Recently, fluorescent quantum dots, especially carbon quantum dots or carbon
53
nanoparticle dots (C-dots), have attracted considerable research interests due to their
54
high biocompatibility, low cost, low toxicity and chemical inertness.19-21 C-dots have
55
been applied for chemical sensors, biosensors, bio-imaging, nanomedicine and
56
photoelectrocatalysis because of their superior properties as mentioned above.22,23
57
Doping of a nitrogen atom into C-dots for forming N-doped C-dots could reduce the
58
contamination of the C-dot surface and increase their stability. However, so far
59
N-doped C-dots have not been applied for the quantitative detection of HS.
60
Therefore, this work aims at establishing a stable and sensitive HS detection
61
method by using the N-doped C-dots. The work was conducted to: 1) evaluate the
62
stability of the N-doped C-dots under extreme pH and ion strength conditions; 2)
63
determine the detection range and detection limit; 3) validate the practical application
64
of this method for real water samples; and 4) explore the fluorescence quenching
65
mechanism. In this way, a simple, anti-interference and reliable method for HS
66
quantification was established. 4
ACS Paragon Plus Environment
Page 4 of 30
Page 5 of 30
Environmental Science & Technology
67 68
MATERIALS AND METHODS
69 70
Chemicals. Ethylene glycol, sodium alginate (SA), ethylenediamine, hydroquinone
71
(H2Q), KCl, MgCl2, FeCl3, CuCl2, Mn(NO3)2, AlCl3, CaCl2, HF, H2SO4, HNO3 and
72
NaHCO3 were purchased from Sinopharm Chemical Reagent Co., China. Disodium
73
anthraquinone-2,6-disulfonate (AQDS), bovine serum albumin (BSA) and quinine
74
sulfate were purchased from Aladdin Co., China. Phosphate buffered saline tablet was
75
purchased from Sigma-Aldrich Co., USA. Suwannee River fulvic acid (Standard I)
76
was purchased from International Humic Substance Society. Commercial humic acid
77
(HA) (Sigma-Aldrich Co., USA) was purified prior to use as reported previously.24
78
Briefly, the commercial HA was dissolved in a NaOH solution (pH=13.0) and filtrated,
79
followed by the adjustment of pH to 7.0 with HCl and filtration; the final solution was
80
freeze-dried. Mili-Q ultrapure water was used in this work. All chemicals were
81
analytical grade.
82
Preparation of N-Doped C-Dots. The N-doped C-dots were prepared using a
83
modified hydrothermal method reported by Hu et al.25 Briefly, 25 mL ethylene glycol
84
was placed into a 50 mL poly(tetra-fluoroethylene) (Teflon)-lined autoclave and
85
heated at 200 °C for 5 h. After cooling to 20 °C, ethylenediamine of 1.35 mL was
86
added into the obtained homogeneous solution. After stirring for 30 min, the mixtures
87
were heated at 180 °C for 5 h. After cooling to room temperature, the N-doped C-dots
88
were obtained.
89
Characterization of N-Doped C-Dots. The functional groups of the N-doped
90
C-dots were characterized by FTIR (Bruker Co., Germany) with air as the background.
91
The sample spectra were scanned from 400 cm-1 to 4000 cm-1 with a resolution of 4 5
ACS Paragon Plus Environment
Environmental Science & Technology
92
cm-1. The main surface chemical elements were characterized by ESCALAB 250
93
X-ray photoelectron spectroscopy (XPS, VG Instrument Co., USA). The
94
morphologies of the N-doped C-dots were imaged by transmission electron
95
microscopy (TEM, GATAN Instrument Co., USA). All ultraviolet-visible absorption
96
spectra were obtained using a UV-Vis spectrophotometer (Model 2450, Shimadzu Co.,
97
Japan). The fluorescence spectra and excitation emission (Ex/Em) matrix were
98
measured using a fluorescence spectrophotometer (Aqualog, Horiba Co., Japan),
99
while the fluorescence lifetime was determined with a steady state/transient
100
fluorescence spectrometer (JY Fluorolog-3-Tou, Jobin Yvon Co., France).
101
To explore the quenching mechanism of the N-doped C-dots by AQDS, HA and
102
H2Q, electrochemical experiments were conducted on an electrochemical workstation
103
(CHI760D, CHI Instruments Co., China). As reported previouly,26,27 a 1-mm diameter
104
planar platinum disk was used as the working electrode. Pt wire and Ag/Ag+ electrode
105
were used as the counter electrode and the reference electrode, respectively. The Pt
106
disk electrode was sequentially polished, washed by water, sonicated three times and
107
activated with H2SO4 before each experiment. N2 was purged for 15 min before the
108
tests.
109
Measurement of HS in Natural Water Samples. Before the measurement, the
110
anti-interference capacity of this method was evaluated. BSA and SA, as the dominant
111
organics in DOM, were separately selected as the interfering substances and the
112
impacts of their concentration on the HA detection was examined. Moreover, the
113
impacts of several ions, which were selected according to the reference,28 on the
114
fluorescence intensity of the N-doped C-dots were also evaluated.
115
In a typical HS detection procedure, 50 µL of the as-prepared N-doped C-dots
116
was added to 5-mL HS solution to give a final C-dots concentration of 1% (v/v). The 6
ACS Paragon Plus Environment
Page 6 of 30
Page 7 of 30
Environmental Science & Technology
117
optimal concentration of the N-doped C-dots was selected according to its
118
fluorescence performance (Fig. S1). Then, the mixture was sufficiently shaken by
119
vortex and the fluorescence of the N-doped C-dots was recorded by a
120
spectrophotometer (JY Fluorolog-3-Tou, Jobin Yvon Co., France). In order to evaluate
121
the feasibility of the proposed method, three sample sets from artificial water sources,
122
wetland sources, municipal wastewater treatment plant (WWTP) sources and pool
123
sources were collected and tested in May, 2017. Samples from Chaohu Lake
124
(31°32.081' N, 117°38.845' E), Anhui Province, China, were used as the natural water.
125
The wetland sample series was collected from the Artificial Wetland Park (31°71.803'
126
N, 117°40.102' E), Hefei City, China. The influent and effluent samples of the WWTP
127
were collected from the Jingkaiqu WWTP (Hefei City, China). The last water sample
128
series were collected from three different pools in the campus of our university
129
(31°84.302' N, 117°27.536' E), Hefei City, China. The standard addition recovery
130
method was adopted to measure the HS in natural water samples and triplicate
131
measurements were conducted for each sample. The recovery of HS was calculated as
132
follows: P=(C2-C1)/C3×100%
(1)
133
where P (%) is the HS recovery, C1, C2, and C3 (mg/L) are the detected HS
134
concentrations in the pristine sample, the measured HS concentration after dose of a
135
certain amount of standard HS into sample solution, and the quantity of standard HS
136
added to the solution, respectively.
137 138
RESULTS AND DISCUSSION
139 140
Properties of the N-Doped C-Dots. The as-prepared N-doped C-dots were well 7
ACS Paragon Plus Environment
Environmental Science & Technology
141
mono-dispersed and uniform (Figure S2). Their average diameters were 5.7 nm and
142
they were distributed predominantly in a narrow range of 3.5-7.5 nm (Fig. 1A). The
143
N-doped C-dots exhibited a quantum yield of approximately 15% (Fig. S3, for
144
detailed procedures, SI). Their full range XPS analysis (Fig. 1B) clearly showed C 1s
145
(284.8 eV), N 1s (399.9 eV) and O 1s (531.7 eV) signals.29 The C 1s energy peak was
146
divided into 3 peaks for the N-doped C-dots ascribed to the C=C (284.5 eV), C-N
147
(286.0 eV) and C-O species (287.8 eV) (Fig. S4A).23 The N 1s energy peak reveals
148
that nitrogen was mostly in the form of graphite-like structure (N-C3) (398.3 eV),
149
pyridinic N (399.9 eV) and N-H (401.2 eV) (Fig. S4B).30,31 The O 1s exhibits one
150
fitted peak, which was ascribed to C=O (531.7 eV) (Fig. S4C).30 The obtained XPS
151
results validate the successful doping of nitrogen atom into the C-dots. FTIR
152
spectroscopy shows that the three peaks present for the N-doped C-dots were ascribed
153
to the C-N (ca. 1544 cm-1), CO=NH (ca. 1650 cm-1), and C=NH- (or –C≡NH) (ca.
154
2098 cm-1) stretching vibrations (Fig. S5).32 These functional groups also demonstrate
155
that the nitrogen atom was successfully doped into the C-dots. The absorption band ca.
156
3276 cm-1 was attributed to the N-H stretching vibration,33,34 and the peaks ca. 2939
157
cm-1, 2879 cm-1, 1452 cm-1 and 1375 cm-1 were assigned to the C-H stretching
158
vibration.35 The analyses also suggest that the N-doped C-dots were highly
159
hydrophilic.
160
The optical properties of the N-doped C-dots were characterized by fluorescence
161
spectra under different excitation wavenumbers (Fig. 1C). The emission wavelength
162
was red-shifted from 390 nm to 480 nm when the excitation wavelength was
163
increased from 300 nm to 400 nm, suggesting the excitation-dependent fluorescence
164
behavior.36 This result was ascribed to the different sizes and surface states of the
165
as-prepared N-doped C-dots, similar to the behavior observed for the most 8
ACS Paragon Plus Environment
Page 8 of 30
Page 9 of 30
Environmental Science & Technology
166
luminescent graphite quantum dots and carbon dots.37-40
167
To evaluate the stability of the N-doped C-dots, the effects of pH and ionic
168
strength on the fluorescence intensity were further examined. The fluorescence
169
intensity of the prepared C-dots was stable within the pH range of 3.0-12.0 (Fig. 2A).
170
Moreover, the fluorescence strength remained constant as the ionic strength was
171
increased from 10-7 to 1 M (Fig. 2B), implying that there was no ionization of surface
172
groups.41 These results show that the N-doped C-dots were optically stable.
173
Fluorescence Response of N-Doped C-Dots to HS. HA was selected as the
174
representative HS in this work and its fluorescence property was explored. Initially,
175
the fluorescence strength of HA increased as its concentration was increased from 0 to
176
50 mg/L and subsequently decreased with a further increase in its concentration (Fig.
177
3A). This was caused by the inherent property of fluorescence quenching under high
178
concentration conditions. Although HA could be detected by using its fluorescence,
179
the linear range of the fluorescence method was 0-20 mg/L (R2=0.9692). When the
180
N-doped C-dots were added into the HA solution, the peak intensity of the C-dots
181
decreased (Fig. S6) and a wide detection range with 0-100 mg/L HA was achieved
182
(Fig. 3B). To validate the stability of this quantification method, the impact of pH on
183
its accuracy was further evaluated. Although the HA fluorescence changed
184
significantly in the tested pH range of 4.2~9.2, the linear decrease in the fluorescence
185
of the N-doped C-dots was stable (Fig. S7). These results suggest the potential of this
186
method for practical applications.
187
The complex compositions of natural water poses a great challenge to the
188
detection methods not only in sensitivity but also more significantly in selectivity.42
189
Thus, the interferences of proteins and polysaccharides, which are the two widespread
190
organics in DOM,44 to the HA detection were explored. BSA and SA were 9
ACS Paragon Plus Environment
Environmental Science & Technology
191
respectively selected as the representative proteins and polysaccharides. As shown in
192
Fig. 3C and D, the fluorescence strength of the N-doped C-dots did not substantially
193
decrease after adding SA and BSA. Moreover, the effect of their mixture was found to
194
be negligible (Fig. 3E). The selectivity of this detection method was further validated
195
in the presence of metal ions and anions. Several ions extensively present in natural
196
water and wastewater were selected based on the previous reports,28,44 and their
197
dosing concentrations were adopted from the data of Zhou et al.28As shown in Fig. 3F,
198
the interferences of the ions were negligible. These results clearly indicate that the
199
N-doped C-dots were highly sensitive and selective for HA over other organic and
200
inorganic ions in natural water, further implying that the N-doped C-dots could meet
201
the detection requirements for practical use.
202
Possible Fluorescence Quenching Mechanism of N-Doped C-Dots by HS. To
203
characterize the quenching mechanism of the N-doped C-dots by HS, the impact of
204
HA concentration on its own absorbance intensity was examined firstly. The
205
absorbance intensity showed an excellent linear response to the HA concentration
206
regardless the presence of the N-doped C-dots or not (Fig. 4A). This result indicates
207
that there was no static complexation between HA and the N-doped C-dots. In
208
comparison, the time-correlated single photon counting detection results show that the
209
average fluorescence lifetime of the N-doped C-dots was found to decrease with the
210
increasing HA concentration (Fig. 4B). Therefore, the quenching of C-dots
211
fluorescence by HA was a dynamic quenching process, which was possibly caused by
212
the collision between fluorescent and quencher.45
213
HS are able to accept and donate electrons simultaneously,6,46 which is mainly
214
attributed to the existence of the electron-accepting (quinone) and electron-donating
215
(phenol) moieties. To better understand the quenching mechanism, AQDS and H2Q 10
ACS Paragon Plus Environment
Page 10 of 30
Page 11 of 30
Environmental Science & Technology
216
were respectively selected as the quinone and phenol moieties47 and their impacts on
217
the fluorescence of C-dots were explored. Both of them could linearly quench the
218
fluorescence of the N-doped C-dots (Fig. 4C-D). To find out the effect of the
219
quenching, the UV-Vis absorption spectra of AQDS, HA and H2Q were recorded and
220
the fluorescence emission spectrum of the N-doped C-dots at the excitation
221
wavelength of 320 nm was also recorded (Fig.4E). There was no obvious overlapping
222
region between the absorption spectra (AQDS, HA and H2Q) and the fluorescence
223
emission spectrum of the N-doped C-dots, suggesting that the fluorescence resonance
224
energy transfer was not the quenching mechanism of the N-doped C-dots by HS,
225
because there was no energy transfer from the excited C-dots to AQDS, HA and H2Q.
226
The light-excited fluorophore (donor) is able to transfer its excited electrons to
227
another substance (i.e., acceptor) when they are sufficiently close, e.g., via van der
228
Waals contact.48 Therefore, non-radioactive electron-transfer was proposed as a
229
possible quenching mechanism of the N-doped C-dots by HS (Fig. 5). For validation,
230
electrochemical experiments were conducted. A reduction peak at -0.52 V (vs.
231
Ag/AgCl) was observed for the N-doped C-dots in the cyclic voltammetry spectrum
232
while no oxidation peak was observed (Fig. 4F). This is in accordance with the
233
previous observations.41 In comparison, both AQDS (-0.4 V) and HA (-0.36 V)
234
showed a more positive reduction potential and were likely to accept electrons from
235
the C-dots. As a result, the light-induced electron was possibly absorbed by HS and
236
the fluorescence of the C-dots was quenched accordingly.
237
Application of Our Method to Water Samples. Before applying our method to
238
measure water samples, a stability test comparing with the Modified Lowry method
239
was conducted by mixing different proportions of HA and fulvic acid. The determined
240
HS concentrations by these two methods were of almost the same level (Table 1), 11
ACS Paragon Plus Environment
Environmental Science & Technology
241
implying that the proposed method was appropriate for the quantification of HS in
242
natural water samples. Then, the nine water samples from various sources were also
243
analyzed by using our method. The recoveries for these actual samples ranged from
244
92.64% to 131.55% with a relative standard deviation (RSD) of 0.38%-25.00% range
245
(Table 2). Moreover, the linear range and detection limit of the proposed method are
246
comparable to those of the other methods (Table S1), further demonstrating the
247
suitability of this method for the HS detection of natural water samples.
248
Implications of This Work. A new method with a high detection range (0-100
249
mg/L) and a great selectivity for HS quantification was established by using the
250
N-doped C-dots as a probe in this work. The detection limit of this method was 0.2
251
mg/L, which was sufficient for HS quantification in surface water as its typically is in
252
a range of 0.5-20 mg/L.1 Currently, the HS content is quantified by the modified
253
Lowry method.49 However, the steps are complicated and the detection limit of the
254
modified Lowry method is approximately 1.3 mg/L. Compared to the modified Lowry
255
method, the C-dots fluorescence quenching-based method developed in this work is
256
easier and more appropriate for high-concentration HS determination. Additionally,
257
this method exhibits a wider detection range with a low background noise compared
258
to the other methods. More importantly, this developed detection method is universal
259
because the other N-doped C-dots synthesized by different methods are also able to
260
quantify HS in water (SI, Section S3), as evidenced by the HS detection results for the
261
N-doped C-dots synthesized with the microwave-assisted method (Fig. S8).
262
Furthermore, since C-dots could be extracted and deposited on the
263
non-fluorescence responsive surface, a portable test paper would be expected. We
264
fabricated a C-dots based test paper (for details, please see SI). The test paper was
265
successfully applied for the quantification of HS at a concentration of 0~20 mg/L (Fig. 12
ACS Paragon Plus Environment
Page 12 of 30
Page 13 of 30
Environmental Science & Technology
266
6). By coupling with the fluorescent excitation and emission, e.g., a Light Emitting
267
Diode lamp, a portable HS detection prototype will be developed in the future.
268 269
AUTHOR INFORMATION
270
†
271
*Corresponding Author: Prof. Han-Qing Yu, Fax: +86-551-63601592. E-mail:
272
[email protected]. ORCID: Han-Qing Yu: 0000-0001-5247-6244
273
Notes: The authors declare no competing financial interest.
These authors contributed equally to this work.
274 275
ACKNOWLEDGMENTS
276
We thank the National Natural Science Foundation of China (21261160489 and
277
51538011), and the Collaborative Innovation Center of Suzhou Nano Science and
278
Technology of the Ministry of Education of China for the support of this work.
279 280
ASSOCIATED CONTENT
281
Supporting Information Available. Experimental details, quantum yield calculation
282
of N doped C-dots (Section S1), preparation of the portable HA test paper (Section
283
S2), preparation of the N-doped C-dots by microwave-assisted method (Section S3),
284
comparison between this work and published methods for HS quantification (Table
285
S1), fluorescence intensity variations of the N-doped C-dots at diffrent concentrations
286
(Fig. S1), transmission electron microscopy (TEM) images of N doped C-dots (Fig.
287
S2), photoluminescence and absorbance of the quinine sulfate and N doped C-dots
288
(Fig. S3), (A) C 1s, (B) N 1s and (C) O 1s of N-doped C-dots (Fig. S4), Fourier
289
transform
290
three-dimensional excitation emission fluorescence spectroscopy (EEM) of N doped
infrared
spectroscopy
(FTIR)
of
N
doped
13
ACS Paragon Plus Environment
C-dots
(Fig.
S5),
Environmental Science & Technology
291
C-dots with increasing HA concentration (Fig. S6), influence of pH on (A)
292
fluorescence of HA and (B) quantification of HA by N doped C-dots (Fig. S7), HA
293
quantification by the N-doped C-dots synthesized with the microwave-assisted
294
method (Fig. S8). This information is available free of charge via the Internet at
295
http://pubs.acs.org/.
296 297
REFERENCES
298 299
(1) Rodrigues, A.; Brito, A.; Janknecht, P.; Proença, M. F.; Nogueira, R.
300
Quantification of humic acids in surface water: effects of divalent cations, pH,
301
and filtration. J. Environ. Monitor. 2009, 11 (2), 377-382.
302 303
(2) Thurman, E. M. Organic Geochemistry of Natural Waters; M. Nijhoff and W. Junk Publishers: Dordrecht, the Netherlands, 1985.
304
(3) Aiken, G. R.; Hsu-Kim, H.; Ryan, J. N. Influence of dissolved organic matter on
305
the environmental fate of metals, nanoparticles, and colloids. Environ. Sci.
306
Technol. 2011, 45 (8), 3196-3201.
307
(4) Jiang, C.; Aiken, G. R.; Hsu-Kim, H. Effects of Natural Organic Matter Properties
308
on the Dissolution Kinetics of Zinc Oxide Nanoparticles. Environ. Sci. Technol.
309
2015, 49 (19), 11476-11484.
310
(5) Croteau, M. N.; Fuller, C. C.; Cain, D. J.; Campbell, K. M.; Aiken, G.
311
Biogeochemical Controls of Uranium Bioavailability from the Dissolved Phase in
312
Natural Freshwaters. Environ. Sci. Technol. 2016, 50 (15), 8120-8127.
313
(6) Lovley, D. R.; Coates, J. D.; Blunt-Harris, E. L.; Phillips, E. J.; Woodward, J. C.
314
Humic substances as electron acceptors for microbial respiration. Nature 1996,
315
382 (6590), 445-448. 14
ACS Paragon Plus Environment
Page 14 of 30
Page 15 of 30
Environmental Science & Technology
316 317
(7) Bolto, B.; Gregory, J. Organic polyelectrolytes in water treatment. Water Res. 2007, 41 (11), 2301-2324.
318
(8) Liang, L.; Singer, P. C. Factors Influencing the Formation and Relative
319
Distribution of Haloacetic Acids and Trihalomethanes in Drinking Water. Environ.
320
Sci. Technol. 2003, 37 (13), 2920-2928.
321 322
(9) Boorman, G. A. Drinking water disinfection byproducts: review and approach to toxicity evaluation. Environ. Health Perspct. 1999, 107, 207.
323
(10) Tremblay, L.; Gagné, J. P. Fast quantification of humic substances and organic
324
matter by direct analysis of sediments using DRIFT spectroscopy. Anal.Chem.
325
2002, 74 (13), 2985-2993.
326
(11) Davis, W. M.; Erickson, C. L.; Johnston, C. T.; Delfino, J. J.; Porter, J. E.
327
Quantitative Fourier Transform Infrared spectroscopic investigation humic
328
substance functional group composition. Chemosphere 1999, 38 (12), 2913-2928.
329
(12) Laglera, L. M.; Battaglia, G.; van den Berg, C. M. Determination of humic
330
substances in natural waters by cathodic stripping voltammetry of their
331
complexes with iron. Anal. Chim. Acta 2007, 599 (1), 58-66.
332 333
(13) Tian, Y.; Jun Song, Q.; Hua, Z. Flow Injection Determination of Humic Acid with Chemiluminescence Detection. Anal. Lett. 2005, 38 (14), 2439-2447.
334
(14) Cheng, X.; Lixia, Z.; Xu, W.; Luo, J. Sensitive monitoring of humic acid in
335
various aquatic environments with acidic cerium chemiluminescence detection.
336
Anal. Sci. 2007, 23 (10), 1189-1193.
337 338
(15) Stevenson, F. J. Humus Chemistry: Genesis, Composition, Reactions, 2nd ed.; John Wiley & Sons, Ltd: New York, 1994.
339
(16) Wu, F. C.; Evans, R. D.; Dillon, P. J.; Cai, Y. R. Rapid quantification of humic
340
and fulvic acids by HPLC in natural waters. Appl. Geochem. 2007, 22 (8), 15
ACS Paragon Plus Environment
Environmental Science & Technology
341
1598-1605.
342
(17) Her, N.; Amy, G.; McKnight, D.; Sohn, J.; Yoon, Y. Characterization of DOM as a
343
function of MW by fluorescence EEM and HPLC-SEC using UVA, DOC, and
344
fluorescence detection. Water Res. 2003, 37 (17), 4295-4303.
345
(18) Murphy, K. R.; Butler, K. D.; Spencer, R. G.; Stedmon, C. A.; Boehme, J. R.;
346
Aiken, G. R. Measurement of dissolved organic matter fluorescence in aquatic
347
environments: an interlaboratory comparison. Environ.Sci.Technol. 2010, 44 (24),
348
9405-9412.
349 350
(19) Lim, S. Y.; Shen, W.; Gao, Z. Carbon quantum dots and their applications. Chem. Soc. Rev. 2015, 44 (1), 362-381.
351
(20) Ding, C.; Zhu, A.; Tian, Y. Functional Surface Engineering of C-Dots for
352
Fluorescent Biosensing and in Vivo Bioimaging. Accounts Chem. Res. 2014, 47
353
(1), 20-30.
354
(21) Medintz, I. L.; Uyeda, H. T.; Goldman, E. R.; Mattoussi, H. Quantum dot
355
bioconjugates for imaging, labelling and sensing. Nat. Mater. 2005, 4 (6),
356
435-446.
357 358
(22) Zhang, J.; Yu, S. H. Carbon dots: large-scale synthesis, sensing and bioimaging. Mater. Today 2016, 19 (7), 382-393.
359
(23) Sun, D.; Ban, R.; Zhang, P. H.; Wu, G. H.; Zhang, J. R.; Zhu, J. J. Hair fiber as a
360
precursor for synthesizing of sulfur- and nitrogen-co-doped carbon dots with
361
tunable luminescence properties. Carbon 2013, 64, 424-434.
362
(24) Chen, W.; Habibul, N.; Liu, X. Y.; Sheng, G. P.; Yu, H. Q. FTIR and synchronous
363
fluorescence heterospectral two-dimensional correlation analyses on the binding
364
characteristics of copper onto dissolved organic matter. Environ. Sci. Technol.
365
2015, 49 (4), 2052-2058. 16
ACS Paragon Plus Environment
Page 16 of 30
Page 17 of 30
Environmental Science & Technology
366
(25) Hu, S.; Tian, R.; Dong, Y.; Yang, J.; Liu, J.; Chang, Q. Modulation and effects of
367
surface groups on photoluminescence and photocatalytic activity of carbon dots.
368
Nanoscale 2013, 5 (23), 11665-11671.
369
(26) Chen, W.; Chen, J. J.; Lu, R.; Qian, C.; Li, W. W.; Yu, H. Q. Redox reaction
370
characteristics of riboflavin: a fluorescence spectroelectrochemical analysis and
371
density functional theory calculation. Bioelectrochemistry 2014, 98, 103-108.
372
(27) Chen, W.; Liu, X. Y.; Qian, C.; Song, X. N.; Li, W. W.; Yu, H. Q. An UV-vis
373
spectroelectrochemical approach for rapid detection of phenazines and
374
exploration of their redox characteristics. Biosens. Bioelectron. 2015, 64, 25-29.
375
(28) Zhou, X. H.; Huang, B. C.; Zhou, T.; Liu, Y. C.; Shi, H. C. Aggregation behavior
376
of engineered nanoparticles and their impact on activated sludge in wastewater
377
treatment. Chemosphere 2015, 119, 568-576.
378
(29) Zhang, H.; Li, Y.; Liu, X.; Liu, P.; Wang, Y.; An, T.; Yang, H.; Jing, D.; Zhao, H.
379
Determination of Iodide via Direct Fluorescence Quenching at Nitrogen-Doped
380
Carbon Quantum Dot Fluorophores. Environ. Sci. Technol. Lett. 2014, 1 (1),
381
87-91.
382
(30) Liu, X.; Jiang, H.; Ye, J.; Zhao, C.; Gao, S.; Wu, C.; Li, C.; Li, J.; Wang, X.
383
Nitrogen-Doped Carbon Quantum Dot Stabilized Magnetic Iron Oxide
384
Nanoprobe for Fluorescence, Magnetic Resonance, and Computed Tomography
385
Triple-Modal In Vivo Bioimaging. Adv. Funct. Mater. 2016, 26 (47), 8694-8706.
386
(31) Wang, L.; Li, B.; Xu, F.; Shi, X.; Feng, D.; Wei, D.; Li, Y.; Feng, Y.; Wang, Y.; Jia,
387
D.; Zhou, Y. High-yield synthesis of strong photoluminescent N-doped carbon
388
nanodots derived from hydrosoluble chitosan for mercury ion sensing via
389
smartphone APP. Biosens. Bioelectron. 2016, 79, 1-8.
390
(32) Tan, J.; Zou, R.; Zhang, J.; Li, W.; Zhang, L.; Yue, D. Large-scale synthesis of 17
ACS Paragon Plus Environment
Environmental Science & Technology
391
N-doped carbon quantum dots and their phosphorescence properties in a
392
polyurethane matrix. Nanoscale 2016, 8 (8), 4742-4747.
393
(33) Liu, R.; Zhang, H.; Liu, S.; Zhang, X.; Wu, T.; Ge, X.; Zang, Y.; Zhao, H.; Wang,
394
G. Shrimp-shell derived carbon nanodots as carbon and nitrogen sources to
395
fabricate three-dimensional N-doped porous carbon electrocatalysts for the
396
oxygen reduction reaction. Phys. Chem. Chem. Phys. 2016, 18 (5), 4095-4101.
397
(34) Jiang, K.; Sun, S.; Zhang, L.; Wang, Y.; Cai, C.; Lin, H. Bright-Yellow-Emissive
398
N-Doped Carbon Dots: Preparation, Cellular Imaging, and Bifunctional Sensing.
399
ACS Appl. Mater. Interfaces 2015, 7 (41), 23231-23238.
400
(35) Cayuela, A.; Carrillo-Carrión, C.; Soriano, M. L.; Parak, W. J.; Valcárcel, M.
401
One-Step Synthesis and Characterization of N-Doped Carbon Nanodots for
402
Sensing in Organic Media. Anal. Chem. 2016, 88 (6), 3178-3185.
403 404
(36) Baker, S. N.; Baker, G. A. Luminescent Carbon Nanodots: Emergent Nanolights. Angew. Chem., Int. Ed. 2010, 49 (38), 6726-6744.
405
(37) Tang, L.; Ji, R.; Cao, X.; Lin, J.; Jiang, H.; Li, X.; Teng, K. S.; Luk, C. M.; Zeng,
406
S.; Hao, J.; Lau, S. P. Deep Ultraviolet Photoluminescence of Water-Soluble
407
Self-Passivated Graphene Quantum Dots. ACS Nano 2012, 6 (6), 5102-5110.
408
(38) Zhu, S.; Zhang, J.; Qiao, C.; Tang, S.; Li, Y.; Yuan, W.; Li, B.; Tian, L.; Liu, F.;
409
Hu, R.; Gao, H.; Wei, H.; Zhang, H.; Sun, H.; Yang, B. Strongly
410
green-photoluminescent graphene quantum dots for bioimaging applications.
411
Chem. Commun. 2011, 47 (24), 6858-6860.
412
(39) Xu, Z. Q.; Yang, Q. Q.; Lan, J. Y.; Zhang, J. Q.; Peng, W.; Jin, J. C.; Jiang, F. L.;
413
Liu, Y. Interactions between carbon nanodots with human serum albumin and
414
gamma-globulins: The effects on the transportation function. J. Hazard. Mater.
415
2016, 301, 242-249. 18
ACS Paragon Plus Environment
Page 18 of 30
Page 19 of 30
Environmental Science & Technology
416 417
(40) Dong, Y.; Wan, L.; Cai, J.; Fang, Q.; Chi, Y.; Chen, G. Natural carbon-based dots from humic substances. Sci. Rep. 2015, 5, 10037.
418
(41) Zhang, H.; Chen, Y.; Liang, M.; Xu, L.; Qi, S.; Chen, H.; Chen, X. Solid-phase
419
synthesis of highly fluorescent nitrogen-doped carbon dots for sensitive and
420
selective probing ferric ions in living cells. Anal. Chem. 2014, 86 (19),
421
9846-9852.
422
(42) Cordes, D. B.; Gamsey, S.; Singaram, B. Fluorescent quantum dots with boronic
423
acid substituted viologens to sense glucose in aqueous solution. Angew. Chem.,
424
Int. Ed. 2006, 45 (23), 3829-3832.
425
(43) Wang, J.; Wang, L.; Miao, R.; Lv, Y.; Wang, X.; Meng, X.; Yang, R.; Zhang, X.
426
Enhanced gypsum scaling by organic fouling layer on nanofiltration membrane:
427
Characteristics and mechanisms. Water Res. 2016, 91, 203-213.
428
(44) Nikanorov, A.; Brazhnikova, L. Water chemical composition of rivers, lakes and
429
wetlands. In types and properties of water; Eolss Publishers Co.:Oxford, 2009.
430
(45) Albani, J. R., Principles and applications of fluorescence spectroscopy. John
431
Wiley & Sons: 2008.
432
(46) Jiang, J.; Kappler, A. Kinetics of Microbial and Chemical Reduction of Humic
433
Substances: Implications for Electron Shuttling. Environ. Sci. Technol. 2008, 42
434
(10), 3563-3569.
435
(47) Sharpless, C. M.; Aeschbacher, M.; Page, S. E.; Wenk, J.; Sander, M.; McNeill, K.
436
Photooxidation-induced changes in optical, electrochemical, and photochemical
437
properties of humic substances. Environ. Sci. Technol. 2014, 48 (5), 2688-2696.
438
(48) Chen, H.; Ahsan, S. S.; Santiago-Berrios, M. E. B.; Abruña, H. D.; Webb, W. W.
439
Mechanisms of quenching of Alexa fluorophores by natural amino acids. JACS.
440
2010, 132 (21), 7244-7245. 19
ACS Paragon Plus Environment
Environmental Science & Technology
441
(49) Frølund, B.; Palmgren, R.; Keiding, K.; Nielsen, P. H. Extraction of extracellular
442
polymers from activated sludge using a cation exchange resin. Water Res. 1996,
443
30 (8), 1749-1758.
20
ACS Paragon Plus Environment
Page 20 of 30
Page 21 of 30
Environmental Science & Technology
Table 1 HS Quantification Using Different Methods (5 mg/L theoretical concentration) sample
measured HS concentration (mg/L)
humic acid
fulvic acid
(mL)
(mL)
modified Lowry method
this method
0
5
4.51±0.11
4.87±0.15
1
4
4.92±0.10
5.26±0.24
2
3
4.92±0.21
4.37±0.33
3
2
5.40±0.20
5.04±0.10
4
1
5.35±0.18
4.60±0.22
measured
21
ACS Paragon Plus Environment
Environmental Science & Technology
Page 22 of 30
Table 2 Detection of HS in Water Samples sample
concentration of HA (mg/L) amount measured
Chao Lake 1
1.14
Chao Lake 1 Chao Lake 2
1.64
Chao Lake 2 Chao Lake 3
0.92
Chao Lake 3 wetland
2.21
wetland WWTP influent
3.62
WWTP influent WWTP effluent
1.36
WWTP effluent campus pond 1
2.38
campus pond 1 campus pond 2
2.13
campus pond 2 campus pond 3 campus pond 3
2.08
recovery
RSD
amount found
(%) (%)
(n=3; %)
5
6.41±0.45
105.30
6.98
10
11.27±0.24
101.19
2.17
5
6.27±0.33
92.64
5.20
10
11.48±0.10
98.38
0.88
5
7.50±2.00
131.55
25.00
10
12.24±1.71
113.23
13.97
5
6.82±0.06
92.19
5.80
10
11.78±0.06
95.69
0.48
5
8.30±1.13
93.66
15.06
10
13.37±0.11
97.55
0.84
5
6.22±0.21
97.28
3.50
10
11.86±0.26
104.99
2.22
5
7.29±0.72
98.20
9.95
10
12.27±0.60
98.88
4.86
5
7.21±0.03
101.70
0.38
10
11.97±0.24
98.38
2.04
5
7.19±0.51
102.14
7.60
10
12.07±0.46
99.83
3.82
amount added
22
ACS Paragon Plus Environment
Page 23 of 30
Environmental Science & Technology
Figure Captions
Figure 1.Characteristics of the as-prepared N-doped C-dots. (A) Particle size distribution, (B) XPS survey and (C) Fluorescence spectra of the N-doped C-dots at different excitation wavelengths.
Figure 2. Fluorescence responses of the N-doped C-dots to the variations of pH (A) and ionic strength (B) with Ex/Em of 320 nm/400 nm.
Figure 3. Selective and sensitive response of the N-doped C-dots to HA. Fluorescence intensity variation of (A) HA with rising concentrations; (B) N-doped C-dots with different HA dosages, inset: the optical image under 302 nm UV lamp; impacts of (C) BSA, (D) SA, (E) mixture of SA, BSA and HA, and (F) metal ions on the fluorescence of the N-doped C-dots.
Figure 4. Fluorescence quenching between HA and the N-doped C-dots. (A) Variation of absorbance at 255 nm with increasing HA concentrations. (B) Average fluorescence lifetime variation of C-dots with increasing HA concentrations. Fluorescence intensity variation of C-dots with the increasing concentration of (C) H2Q and (D) AQDS. (E) Fluorescence spectrum of the N-doped C-dots at the excitation wavelength of 320 nm and UV-Vis absorbance spectra of HA, AQDS and H2Q. (F) Cyclic voltammetry of the N-doped C-dots, AQDS and HA at pH 7.0.
Figure 5. Fluorescence quenching mechanism of the N-doped C-dots by HA.
Figure 6. Fluorescence intensity of HA by the test paper, inset: the optical image images at 302 nm (UV lamp).
23
ACS Paragon Plus Environment
Environmental Science & Technology
Figure 1. Characteristics of the as-prepared N-doped C-dots. (A) Particle size distribution, (B) XPS survey and (C) Fluorescence spectra of the N-doped C-dots at different excitation wavelengths.
24
ACS Paragon Plus Environment
Page 24 of 30
Page 25 of 30
Environmental Science & Technology
Figure 2. Fluorescence responses of the N-doped C-dots to the variations of pH (A) and ionic strength (B) with Ex/Em of 320 nm/400 nm.
25
ACS Paragon Plus Environment
Environmental Science & Technology
Figure 3. Selective and sensitive responses of the N-doped C-dots to HA. Fluorescence intensity variation of (A) HA with rising concentrations; (B) N-doped C-dots with different HA dosages, inset: the optical image under 302 nm UV lamp; impacts of (C) BSA, (D) SA, (E) mixture of SA, BSA and HA, and (F) metal ions on the fluorescence of the N-doped C-dots.
26
ACS Paragon Plus Environment
Page 26 of 30
Page 27 of 30
Environmental Science & Technology
Figure 4. Fluorescence quenching between HA and the N-doped C-dots. (A) Variation of absorbance at 255 nm with increasing HA concentrations. (B) Average fluorescence lifetime variation of C-dots with increasing HA concentrations. Fluorescence intensity variation of C-dots with the increasing concentration of (C) H2Q and (D) AQDS. (E) Fluorescence spectrum of the N-doped C-dots at the excitation wavelength of 320 nm and UV-Vis absorbance spectra of HA, AQDS and H2Q. (F) Cyclic voltammetry of the N-doped C-dots, AQDS and HA at pH 7.0.
27
ACS Paragon Plus Environment
Environmental Science & Technology
Figure 5. Fluorescence quenching mechanism of the N-doped C-dots by HA.
28
ACS Paragon Plus Environment
Page 28 of 30
Page 29 of 30
Environmental Science & Technology
Figure 6. Fluorescence intensity of HA by the test paper, inset: the optical image at 302 nm (UV lamp).
29
ACS Paragon Plus Environment
Environmental Science & Technology
Table of Contents (TOC) Art
30
ACS Paragon Plus Environment
Page 30 of 30