Recent Advances (2012–2015) in the Photocatalytic Conversion of

Sep 11, 2015 - Recent Advances (2012–2015) in the Photocatalytic Conversion of Carbon Dioxide to Fuels Using Solar Energy: Feasibilty for a New Ener...
0 downloads 4 Views 2MB Size
Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

Chapter 1

Recent Advances (2012–2015) in the Photocatalytic Conversion of Carbon Dioxide to Fuels Using Solar Energy: Feasibilty for a New Energy Yasuo Izumi* Department of Chemistry, Graduate School of Science, Chiba University, Yayoi 1-33, Inage-ku, Chiba 263-8522, Japan *E-mail: [email protected]

In this chapter, recent advances in photocatalytic CO2 conversion with water and/or other reductants are reviewed for the publications between 2012 and 2015. Quantitative comparisons were made for the reaction rates in μmol h−1 gcat−1 to acertain the progress of this field although the rates depends on photocatalyst conditions and reaction conditions (temperature, pressure, and photon wavelength and flux). TiO2 photoproduced methane or CO from CO2 and water at rates of 0.1–17 μmol h−1 gcat−1 depending on the crystalline phase, crystalline face, and the defects. By depositing as minimal thin TiO2 film, the rates increased to 50–240 μmol h−1 gcat−1. Gaseous water was preferred rather than liquid water for methane/CO formation as compared to water photoreduction to H2. Pt, Pd, Au, Rh, Ag, Ni, Cu, Au3Cu alloy, I, MgO, RuO2, graphene, g-C3N4, Cu-containing dyes, and Cu-containing metal-organic frameworks (MOFs) were effective to assist the CO2 photoreduction using TiO2 to methane (or CO, methanol, ethane) at rates of 1.4–160 μmol h−1 gcat−1. Metals of greater work function were preferred. By depositing as minimal thin photocatalyst film, the rates increased to 32–2200 μmol h−1 gcat−1. The importance of crystal face of TiO2 nanofiber was suggested. As for semiconductors other than TiO2, ZnO, Zn6Ti layered double hydroxide (LDH), Mg3In LDH, KTaO3, In(OH)3, graphene, graphene oxide, g-C3N4, CoTe, ZnO, © 2015 American Chemical Society In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

ZnTe, SrTiO3, ZnGa2O4, Zn2GeO4, Zr–Co–Ir oxides, Nb2O5, HNbO3, NaNbO3, InNbO4, NiO, Co3O4, Cu2O, AgBr, carbon nanotube, and the composites of these were reported to form methane, CO, methanol, acetaldehyde from CO2 and water at rates of 0.15–300 μmol h−1 gcat−1 that were comparable to rates using promoted TiO2. The band energy designs comprising appropriate conduction band for CO2 reduction and valence band for water oxidation were made progresses in these semiconductors and semiconductor junctions in the three years. If H2 was used as a reductant, Ni/SiO2-Al2O3 formed methane at 423 K under pressurized CO2 + H2 at a rate of 55 mmol h−1 gcat−1. This rate was not enabled by heating the system under dark, suggesting photoactivated reaction followed by thermally-assisted reaction(s) via Ni–H species. As pure photocatalytic reactions from CO2 + H2, methanol formation rates were improved up to 0.30 μmol h−1 gcat−1 by the doping of Ag/Au nanoparticles, [Cu(OH)4]2− anions, and Cu-containing dyes to Zn–Ga LDH. Furthermore, sacrificial reductants, e.g. hydrazine, Na2SO3, methanol, triethanol amine, and triethyamine, were also utilized to form CO, formate, and methanol at rates of 20–2400 μmol h−1 gcat−1 using semiconductor or MOF photocatalysts. Finally, similar to the integrated system of semiconductor photocatalyst for water oxidation and metal complex/enzyme catalyst for CO2 (photo)reduction, two semiconductors (WO3, Zn–Cu–Ga LDH) were combined on both side of proton-conducting polymer to form methanol at a rate of 0.05 μmol h−1 gcat−1 from CO2 and moisture. These promotion of photoconversion rates of CO2 and new photocatalysts found in these three years have indicated the way beyond for a new energy.

Introduction To enable carbon neutral cycle in modern industrial society, CO2 conversion into fuels utilizing natural (sustainable) energy is one of the ideal methods. Carbon monoxide, methane, methanol, acetaldehyde, and ethane obtained from CO2 are attractive products because they can be easily intergrated into the existing fuel and chemical technology. Although various review articles have been published dealing with the conversion of solar energy into fuels (1, 2) and the conversion of CO2 into fuels (3–8) until 2012, the researches and developments are more intensive during 2012 and 2015 for the target of CO2 reduction into fuels that enables carbon neutral and suppresses the anthropogenic increase of CO2 concentrations in the atmosphere. In this chapter, recent advance based on various intensive researches between 2012 and 2015 in the CO2 photoconversion into fuels is reviewed in hope for a new energy. Similar to previous review for studies before early 2012 (4), the scope 2 In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

of this chapter is limited to semiconductor photocatalysis for the conversion of CO2. Especially, some orders of increase for the CO2 conversion rates and new photocatalysts are focused.

Photon Energy Conversion of CO2 to Fuels with Water 1. TiO2 Photocatalysts

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

1.1. Difference of Crystal Phases The CH4 formation rate was 0.19 μmol h−1 gcat−1 in atomospheric pressure of CO2 and moisture using TiO2 (9). Under similar reaction conditions using some crystal phases of TiO2, the CO formation rates were in the order

If the TiO2 photocatalysts were preheated at 483 K in a flow of helium to make defects, the CO formation rates were in the order

The order did not change if minor methane formation was added to the CO formation (Table 1). The binding of CO2 on Ti3+ sites and the reduction of the bound CO2− species by O-defect sites were suggested (10).

The activity order reported in reference (11) was consistent with equation 1. Furthermore, the anatase:brookite phase ratio was varied by changing the amout of urea used during the TiO2 synthesis. The improved photoconversion of CO2 suggested heterojunction effects of two crystalline phases.

3 In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Table 1. Reported CO2 Photoreduction Catalysts, Reaction Conditions, and the Formation Rates in Water/with Moisture Using TiO2 T (K)

Light source

Reactor

Major product {formation rate (μmol h−1 gcat−1)}

Ref

Room T

100W Hg

Closed

CH4 (0.19)

(9)

150 W solar simulator

Stainless steel, Flow

CO (3.3)

(10)

TiO2 (rutile)

CO (0.82)

(10)

TiO2 (brookite)

CO (1.5)

(10)

Defective TiO2 (anatase)a

CO (10.4), CH4 (2.5)

(10)

Defective TiO2 (rutile)a

CO (4.0)

(10)

Defective TiO2 (brookite)a

CO (17.0), CH4 (1.9)

(10)

CO (1.2)

(11)

TiO2 (atatase:brookite =3:1

CO (2.1)

(11)

TiO2 (brookite)

CO (0.7)

(11)

CH4 (1.2)

(12)

Reactants

4

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

Photocatalyst Brand name

Amount (mg)

CO2

H2O

P25

10

Atmosph. P

Atmosph. P

TiO2 (anatase)

100

99 kPa

2.3 kPa

TiO2 (anatase)

TiO2 (anatase) {010}

100

100

Atmosph. P

101 kPa

Saturated

Liq (1 mL)

150 W solar simulator

293

300 W Hg

Stainless steel

Pyrex

In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Reactants

Ref

TiO2 (anatase) {101}

CH4 (0.74)

(12)

TiO2 (anatase) {001}

CH4 (0.19)

(12)

CH4 (0.15)

(13)

TiO2 (anatase) {001}:{101} =58:42

CH4 (1.4)

(13)

TiO2 (anatase){001}: {101}=83:17

CH4 (0.55)

(13)

Brand name

TiO2 (anatase) {001}:{101} =11:89

Amount (mg)

CO2

T (K)

Light source

H2O

100

5

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

Reactor

Major product {formation rate (μmol h−1 gcat−1)}

Photocatalyst

P25

20

200 kPa

12.3 kPa

323

100 W Xe

Stainless steel

CO (1.2), CH4 (0.38)

(15)

P25

20

200 kPa

Liq (4 mL)

323

100 W Xe

Stainless steel

CO (0.80), CH4 (0.11)

(15)

TiO2 (anatase)

500

Saturated

Liq (1 L)

303

UV lamp

Pyrex

CH4 (11)

(18)

TiO2 nanofiber

5

Atmosph. P

Satur. P

CO (12), CH4 (6)

(20)

TiO2 (anatase)

Film

Atmosph. P

Satur. P

CO (240)

(26)

500 W Xe Room T

400 W Xe

Stainless steel, Flow

Continued on next page.

In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Reactants

Photocatalyst Brand name

a

Amount (mg)

P25

1.25 cm2 Film

TiO2

100

CO2

H2O

190 kPa

Satur. P

T (K)

Light source

Reactor

Major product {formation rate (μmol h−1 gcat−1)}

Ref

400 nm) Solar Simulator, AM1.5

High P cell

CH4 (120)

graphene(2%)TiO2

100

Atmosph. P

Liq (0.4 mL)

300 W Xe arc

graphene-TiO2

10

Atmosph. P

Liq (0.4 mL)

300 W Xe arc

g-C3N4-NTiO2

100

Atmosph. P

Satur. P

303

300 W Xe arc

Teflon

CO (12)

(25)

Pt(0.21%b)TiO2

Film

Atmosph. P

Satur. P

Room T

400 W Xe

Stainless steel, Flow

CH4 (420)

(26)

CH4 (1400)

(26)

Glass

Pt(0.94%b)TiO2

Continued on next page.

In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

12

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

Table 2. (Continued). Reported CO2 Photoreduction Catalysts, Reaction Conditions, and the Formation Rates in Water/with Moisture Using Metal, Metal Oxide, or Other Additive-Loaded TiO2 Reactants

Reactor

Major product {formation rate (μmol h−1 gcat−1)}

Ref

Pt(1.3%b)TiO2

CH4 (630)

(26)

Pt(2.5%b)TiO2

CH4 (63)

(26)

CH4 (32)

(27)

CH4 (44)

(27)

Photocatalyst Brand namea

Amount (mg)

Au(1.5%)-P25

50

Au(0.5%)Cu(1%)-P25

50

CO2

T (K)

Light source

H2O

190 kPa

Satur. P

400 nm)

CH4 (0.89)

(27)

CH4 (40)

(27)

CH4 (210)

(27)

Au(0.5%)Cu(1%)-P25

CH4 (2200)

(27)

Cu(1.5%)-P25

CH4 (280)

(27)

CH4 (0.3)

(28)

Cu(1.5%)-P25 Au(1.5%)-P25

Cu(bpy)2-P25

50 0.6 (1.25

100

cm2)

Gas

Gas

λ>400 nm

In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Reactants

Photocatalyst

a

Amount (mg)

Cu3(btc)2core|TiO2shell

300

Cu3(btc)2

200

CO2

H2O

150 kPa

Liq (5 mL) not immersed

The loading ratio is weight % except for

b.

b

T (K)

Light source

Reactor

Major product {formation rate (μmol h−1 gcat−1)}

Ref

313

300 W Xe arc (λ>400 nm)

Stainless steel

CH4 (2.6)

(29)

none

(29)

Atomic %.

13

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

Brand

namea

In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

2.2. Effective Thin Layer Photocatalysts

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

The CO2 reduction rates using moisture and Pt-supported TiO2 were improved by the deposition of photocatalyst thin layer (26). Ti(i-OC3H7)4 was bubbled by N2 gas and deposited on indium tin oxide (ITO)-coated glass maintained at 773 K. Then, platinum was sputtered on the TiO2 film. Based on the images of fieldemission scanning electron microscopy (FE-SEM), the TiO2 film comprised single crystal rods grown on the glass with a typical column diameter of 250 nm and height of 1.5 μm and possessing an orientation of anatase {1 1 2} plane (Figure 3).

Figure 3. FE-SEM image of thin Pt-TiO2 film deposited from Ti(i-OC3H7)4 and Pt sputtering (26). Reproduced from reference listing (26). Copyright 2012, ACS.

Due to the high dispersion, the TiO2 film produced CO at higher rate per unit amout of photocatalyst: 240 μmol h−1 gcat−1 from CO2 and moisture (Table 1). When the Pt atomic % was 0.21, 0.94, 1.3, and 2.5, the average Pt particle size was 0.63, 1.0, 1.3, and 1.9 nm, respectively. By the doping of Pt, the selectivity changed from CO to CH4. This selectivity change was ascribed that sufficient electrons were accumulated in Pt and thermodynamically stable CH4 was produced rather than CO. The CH4 formation rates were maximal at 0.94 atomic % of Pt. By checking the TiO2 surface coverage of Pt nanoparticles, the increase of methane formation rates until 0.94 atomic % of Pt was ascribed to the increased number of effective Pt sites. The decrease above 0.94 atomic % of Pt was ascribed to particle size effects of Pt. Namely, the reduction potential for Pt nanoparticles is similar to the CB of TiO2 (≈0 V versus SHE) and electrons excited in CB of TiO2 would shift to Pt (Figure 4, middle). In contrast, when the Pt nanoparticle size increase at the higher loading, the potential shift to +1.21 V versus SHE as the WF of Pt is 5.65 eV, thereby both electrons and holes tend to shift to Pt and recombine (Figure 4, right) (26).

14 In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

The CO2 reduction using moisture and metal-supported TiO2 was further improved irradiated by 1000 W-Xe lamp, pressurized reactor cell (190 kPa of CO2), and also the deposition of photocatalyst thin layer (0.6 mg per 1.25 cm2) (27). Using sequentially-deposited and hydrogen-reduced (@673 K) Au(0.5 wt%)-Cu(1.0 wt%)-TiO2 photocatalyst, methane was formed at a rate of 2200 μmol h−1 gcat−1 (Table 2). In comparison to the performance of Au(1.5 wt%)-TiO2 and Cu(1.5 wt%)-TiO2 photocatalysts (210–280 μmol h−1 gcat−1), Au–Cu alloy phase detected in high-resolution transmission electron microscopy (HR-TEM) seemed to be specifically effective. The role of hydrogen-reduced Ti3+ sites was also suggested to donate electrons to CO2.

Figure 4. CO2 photoreduciton mechanism using Pt-TiO2 nanostructured film. The photogenerated electrons move fast inside the highly-oriented TiO2 single crystals and flow to the Pt nanoparticles, where the reduction reaction occurs to convert CO2 into CO or CH4 (middle) (26). Reproduced from reference listing (26). Copyright 2012, ACS.

Using 125-W high-pressure Hg and 150-W Xe lamps (with cutoff filter of λ > 400 nm) for ultraviolet (UV) and visible irradiations, respectively, for Au-CuTiO2 photocatalyst, no product and methane only were formed, respectively (Table 2) (27). Thus, SPR (the wavelength 570–580 nm) effect of Au in visible light region was suggested to transfer the hot electrons to Cu sites (Figure 5). Carbene pathway was proposed based on Fourier transform infrared (FTIR) rather than formaldehyde pathway (Scheme 1) (5).

15 In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

Figure 5. Proposed photocatalytic reaction mechanism of CO2 reduction with moisture using Au(0.5 wt%)-Cu(1.0 wt%)-TiO2 photocatalyst (27). Reproduced from reference listing (27). Copyright 2014, ACS.

16 In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

Scheme 1. Two proposed mechanisms for the photoreduction of CO2 to methane: formaldehyde (left) and carbine pathways (right) (5). Reproduced from reference listing (15). Copyright 2013, John Wiley and Sons.

17 In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

3. Metal Oxide or Metal-Organic Framework (MOF)-Loaded TiO2 Photocatalysts The Pt-TiO2 photocatalyst in previous section was further doped with MgO (15). It became methane selective and total formation rate of methane and CO (11 μmol h−1 gcat−1) increased by a factor of 1.8 compared to that using Pt-TiO2 (Table 2). Doped MgO layer would help CO2 chemisorption over the catalyst and improve the selectivity for CO2 reduction versus proton reduction. The Cu bipyridyl (bpy) dye to TiO2 also promoted the photoreduction of CO2 to methane at a rate of 0.3 μmol h−1 gcat−1 (Table 2) (28). The assembly of TiO2 with MOF was also reported (29). Cu3(btc)2 (btc = benzene-1,3,5-tricarboxylate) microcrystals synthesized in the presence of polyvinylpyrrolidone were mixed with tetrabutyl titanate in ethanol and then in HF aqueous solution. By heating at 453 K for 12 h, anatase-phase TiO2 shells of mean thickness of ~200 nm over the Cu3(btc)2 cores were formed (Figure 6). Methane was formed using Cu3(btc)2-core|TiO2-shell from CO2 and water irradiated by visible light (λ > 400 nm) at a rate of 2.6 μmol h−1 gcat−1, much higher than than the sum of rates using each component (0.52 and ~0 μmol h−1 gcat−1; Tables 1, 2). Exclusive selectivity to methane rather than H2 was also claimed, probably due to high electron density in the core-shell structure for the eight electron reduction to methane. A 1-ps build-up time in the transient absorption (TA) spectroscopy for the Cu3(btc)2-core|TiO2-shell suggested electron transfer/relaxation from CB of TiO2 to the interface state with Cu3(btc)2 (29).

Figure 6. (a) Core–shell structure, (b) TEM, and (c) SEM images of Cu3(btc)2@TiO2 (29). Reproduced from reference listing (29). Copyright 2014, John Wiley and Sons. 4. Semiconductor Photocatalysts Other Than TiO2 4.1. Photocatalysts Comprising Single Compound

4.1.1. Metal Oxides and Hydroxides By the irradiation of deep UV light at 185 nm from Hg lamp and using the synthetic quartz windows for the reactor (Figure 7), CO2 (9.6 kPa) was converted into CH4 with saturated moisture at a rate of 2.1 μmol h−1 for 13.9 h in the absence of catalyst (Table 3). It was suggested that water photolysis was the exclusive 18 In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

hydrogen source for the CO2 conversion (see Photon energy conversion of CO2 to fuels with hydrogen or sacrificial reducing agents, section 1). The conversion of CO2 was accelerated (7.7 μmol h−1; Table 3) in the presence of Zn6Ti LDH (100 mg), but the addition of MgO, TiO2, CeO2, or HY-zeolite rather reduced the photocomversion rates of CO2 (30). A series of LDHs of [Ni3MIII(OH)8]2CO3·mH2O, III III [Mg3M (OH)8]2CO3·mH2O, and [Zn3M (OH)8]2CO3·mH2O (MIII = Al, Ga, and In) was tested for CO2 photoreduction in water (31). [Mg3MIII(OH)8]2CO3·mH2O was relatively active, e. g. [Mg3In(OH)8]2CO3·mH2O produced CO and O2 at the formation rates of 3.2 and 17 μmol h−1 gcat−1, respectively (Table 3). [Mg3MIII(OH)8]2CO3·mH2O was selective to form hydrogen whereas III [Ni3M (OH)8]2CO3·mH2O was relatively selective to CO formation. The affinity of the surface with CO2 may be related. Hexagonal nanoplate-textured micro-octahedron Zn2SnO4 as large as a few microns was synthesized and tested for CO2 photoreduciton with 0.4 mL of water (32). Due to its small (quantum) size, the band gap was relative wide (3.87 eV) in which the VB maximum at 2.7 eV and CB minimum at −1.17 eV. The methane formation rate increased from 4.8 to 35 ppm h−1 gcat−1 by loading of 1 wt% of Pt and 1 wt% of RuO2 to nanoplate-textured micro-octahedron Zn2SnO4. KTaO3 photocatalytically reduced CO2 with water irradiated by Xe arc lamp to form CO at a rate of 0.34 μmol h−1 gcat−1 (Table 3) (33). Mesoporous In(OH)3 photoproduced methane from CO2 and water at a rate of 0.8 μmol h−1 gcat−1 (Table 3). The rate was by 20 times greater thant that using In(OH)3 without mesoporous structure due to the difference of specific surface area and pore volume (34). Monoclinic Bi6Mo2O15 sub-nanowires photocatalyzed CO2 to methane and the rate was maximal by the preheating at 1073 K. Surface oxygen vacancy created by the heating was considered as an electron trap (35).

Figure 7. Left: Photoreactor composed by 185 nm-Hg lamp (1), synthetic quartz windows (2), and gas chamber (3). Right: Upper view showing the shallow bed of the photocatalyst placed in the photoreactor (30). Reproduced from reference listing (30). Copyright 2012, ACS. 19 In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

20

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

Table 3. Reported CO2 Photoreduction Catalysts, Reaction Conditions, and the Formation Rates in Water/with Moisture Using Semiconductor Photocatalysts Other Than TiO2 Reactants

Photocatalyst Brand name

Amount (mg)

CO2

H2O

9.6 kPa

Satur. P

T (K)

Light source

Reactor

Major product {formation rate (μmol h−1 gcat−1)}

Ref

338

Hg (185, 254 nm)

Quartz

CH4 (2.1a)

(30)

No catalyst

–—

KY-zeolite

500

CH4 (3.1)

(30)

Zn6Ce LDH

500

CH4 (4.3)

(30)

Zn6Ti LDH

500

CH4 (3.3)

(30)

Zn6Ti LDH

100

CH4 (77)

(30)

Mg3In LDH

100

500 μmol

Liq (4 mL)

(31)

KTaO3

100

Atmosph. P

Liq (6 mL)

Pt(0.5 %)-In(OH)3

200

80 kPa

Liq (2–3 mL)

Graphene Oxide

200

101 kPa

Satur. P

g-C3N4 (bulk)

20

60 kPa

Liq (0.1 mL)

300 W Xe arc

298

200 W Hg-Xe

Quartz

CO (3.2)

Borosilicate

CO (0.34)

(33)

300 W Xe arc

Circulated

CH4 (0.8)

(34)

300 W halogen

Stainless

CH3OH (0.17)

(36)

300 W Xe

Teflon-lined

CH3CHO (3.9)

(37)

CH4 (4.8)

(37)

CH4 (5.0)

(38)

g-C3N4 (nanosheet) CoTe

–—

124 kPa

Satur. P

288

300 W Xe (λ > 420 nm)

Quartz

In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Reactants

Photocatalyst

21

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

Brand name

Amount (mg)

CO2

H2O

T (K)

Light source

Reactor

Major product {formation rate (μmol h−1 gcat−1)}

Ref

288

300 W Xe arc (λ > 420 nm)

Quartz

CH4 (44)

(39)

ZnTe(3.4%)ZnO

10

Saturated

Liq (80 mL)

ZnTe(25%)SrTiO3

20

Atmosph. P

Satur. P

300 W Xe arc (λ > 420 nm)

Quartz

CH4 (2.4)

(40)

ZnGa2O4

100

Atmosph. P

Liq (0.4 mL)

300 W Xe arc

Glass

CH4 (0.26)

(41)

ZnGa2O4:Zn2GeO4 (4.5:1)

100

CH4 (3.9)

(41)

CO (1.7)

(45)

CH4 (4.9), CO (0.82)

(46)

CH4 (2.5)

(46)

CH4 (0.15)

(47)

5

101 kPa

13 Pa

355 nm laser

Pt(0.5%)-cNaNbO3

100

80 kPa

Satur. P

300 W Xe arc

Pt(0.5%)-oNaNbO3

100

Pt(0.4%)Nb2O5

100

Pt(0.4%)HNb3O8

100

CH4 (0.47)

(47)

Pt(0.4%)SiO2-HNb3O8

100

CH4 (2.9)

(47)

Pt(0.4%)-SiO2 pillar-HNb3O8

100

CH4 (3.8)

(47)

Zr-Co-IrSBA-15

89 kPa

81 kPa

12 kPa

333

350 W Xe

Pyrex

Quartz

20 kPa

Continued on next page.

In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

22

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

Table 3. (Continued). Reported CO2 Photoreduction Catalysts, Reaction Conditions, and the Formation Rates in Water/with Moisture Using Semiconductor Photocatalysts Other Than TiO2 Reactants

Photocatalyst Brand name

Amount (mg)

T (K)

CO2

H2O

Saturated

0.2M KHCO3

Light source

Reactor

Major product {formation rate (μmol h−1 gcat−1)}

Ref

500 W halogen

Pyrex

CH3OH (1.4)

(48)

InNbO4

140

NiO(0.5%)InNbO4

140

CH3OH (1.6)

(48)

Co3O4(1.0%)InNbO4

140

CH3OH (1.5)

(48)

Pt-o-NaNbO3

50

none

(49)

Pt-g-C3N4

CH4 (0.8)

(49)

Pt-g-C3N4/oNaNbO3

CH4 (6.4)

(49)

CO (29)

(50)

CH4 (300)

(51)

g-C3N4

CH4 (0.26)

(52)

graphene (15%)-g-C3N4

CH4 (0.59)

(52)

Atmosph. P

300 W Xe arc (λ > 420 nm)

Liq (4 mL)

ZnO-g-C3N4

10

400 kPa

Liq (4 mL)

Pt(0.5%)-red P-g-C3N4

20

Atmosph. P

Liq (0.2 mL)

353

500 W Xe (λ > 420 nm)

Pyrex vessel

Stainless steel

500 W Xe arc

In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Reactants

Photocatalyst

a

Amount (mg)

CO2

H2O

Light source

Reactor

Major product {formation rate (μmol h−1 gcat−1)}

Ref

RGO(0.5%)Cu2O

500

Atmosph. P

Liq (3 mL)

150 W Xe

Glass

CO (0.43)

(53)

Ag/AgBr/ CNT

500

7.5 MPa

0.2M KHCO3 (100 mL)

150 W Xe (λ > 420 nm)

Stainless steel

CH4 (30), CH3OH (18), CO (8.0)

(54)

μmol of CH4 h−1.

23

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

Brand name

T (K)

In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

4.1.2. Carbon-Related Materials Graphene oxide (GO) with lateral dimension of several micrometers and thickness of 1–3 nm was exfoliated from graphite in acids and tested for CO2 reduction with moisture irradiated by UV–visible light (36). The methanol formation rate (0.17 μmol h−1 gcat−1) was by a factor of 5.8 higher compared to one using TiO2 under the reaction conditions (Table 3). The CB minimum estimated for GO (−0.79 V versus SHE) would bend to nearly close to reduction potential from CO2 to methanol (−0.38 V versus SHE) if the GO with electron-drawing oxygenated functional groups was p-type semiconductor. Bulk g-C3N4 with the Bruanuer–Emmett–Teller surface area (SBET) of 50 m2 g−1 was compared to g-C3N4 nanosheet with SBET of 306 m2 g−1 (37). Clear difference of selectivity to acetaldehyde and methane (−0.24 V) was observed and one of the major reasons was the difference of band gap (BG), 2.77 and 2.97 eV, respectively. More negative electron potential for the latter sample was considered to effectively reduce CO2 via glyoxal to acetaldehyde and then to methane (5).

4.1.3. Other Materials As one of the metal calcogenide compounds, the CB of hydrothermallysynthesized CoTe positioned at relatively negative potential and the BG was 2.05 eV. The methane formation rate using CoTe was 5.0 μmol h−1 gcat−1 (Table 3) (38).

4.2. Assembled Photocatalysts

4.2.1. Zn, Cu-Containing Compounds The doping of high-potential ZnTe to ZnO was reported (39). The BG of ZnTe was 2.2 eV and the CB minimum was at −1.8 V versus SHE. Due to the excited electrons to CB of ZnO and holes remained at VB of ZnTe, methane was formed irradiated by visible light (λ > 420 nm). ZnTe was a sensitizer for visible light, but the reason of quite high formation rate (44 μmol h−1 gcat−1; Table 3) from CO2 to methane via electron transfer from CB of ZnO is not known and control reaction tests are needed. High-potential ZnTe was also combined with SrTiO3 and formed methane from CO2 and moisture (Table 3) (40). The performance of CO2 photoreduction to methane using cubic spinel ZnGa2O4 was improved by mixing pseudo cubic inverse spinel Zn2GeO4 from 0.26 to 3.9 μmol h−1 gcat−1 (Table 3) (41). One of the reasons was suggested to be the reduction of band gap from 4.45 to 4.18 eV to utilize wider spectrum of light (42). Zn-doped (100)-oriented p-GaP was utilized for CO2 photoreduction with water irradiated by a laser light at 532 nm. To prevent the photocorrosion of GaP, atomic layer deposition of Ti choloride and water vapor was performed to 24 In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

create 1–10 nm-thick TiO2 layers over GaP (43). Methanol was formed on the GaP photoelectrode covered with 5 nm-thick TiO2 at a rate of 1.2 μmol h−1 cmcat−2 at the applied voltage of −0.5 V (versus SHE) in 0.5 M NaCl and 10 mM pyridine solution. Thin TiO2 layer seemed not just the passivation layer to transmit the light at 532 nm, but also to serve to form p–n junction for charge separation (43). Cu2O electrodeposited on CuO nanorods perpendicularly grown on Cu foil photoreduced CO2 in CO2-saturated 0.1 M Na2SO4 aqueous solution at the electric potential smaller than 0.37 V (versus SHE) irradiated by simulated AM 1.5 light. The geometry of CuO nanorod and Cu2O shell should facilitate charge separation irradiated by light and CO2 reduction on CuO (44).

4.2.2. Zr, Co, Ir-Containing Compounds Stepwise synthesis of photoreduction sites of CO2 and photooxidation sites of water in single sample was reported. Zirconocene dichloride was reacted with an ordered mesoporous SiO2, SBA-15, to form Zr-SBA-15 (45). The Co precursor preferably reacted with Zr–OH group to form links of ZrIV–O–CoII in Zr(1.1 mol%)-Co(0.7 mol%)-SBA-15. IrIII acetylacetonate was photodeposited on Zr-Co-SBA-15, but not on Zr-SBA-15 and Co-SBA-15, suggesting electron transfer by the irradiation of 355 nm laser light from Co to Zr (ZrIII–O–CoIII) coupled with the electron transfer from Ir to Co (IrIII···O–CoIII → IrIV–O–CoII). Though the IrIV–O–CoII link may be lost upon calcination later than the electrodeposition, ZrIV–O–CoII and IrOx nanocluster were formed in the vicinity over SBA-15. The CO formation at a rate of 1.7 μmol h−1 gcat−1 under 101 kPa of CO2 and 13 Pa of water irradiated by laser at 355 nm (127 mW cm−2; Table 3) was ascribed to water oxidation on IrOx nanocluster and the resultant electron transfer to neighboring CoII and then to ZrIV (45). Spectroscopic insight for the interaction of ZrIII and CO2 would be expected.

4.2.3 Nb-Containing Compounds Two phases of perovskite-type NaNbO3 doped with 0.5 wt% of Pt were tested (Table 3) (46). One is cubic NaNbO3 (c-NaNbO3) and the other is more common orthorhombic NaNbO3 (o-NaNbO3). The Pt-c-NaNbO3 photocatalyst produced major methane (4.9 μmol h−1 gcat−1) and minor CO (0.82 μmol h−1 gcat−1) from gaseous CO2 and moisture, and the methane formation rate was by a factor 2.0 greater compared to that using Pt-o-NaNbO3. Two reasons of the difference was suggested to be (1) minor difference of band gap value and (2) homogeneous frontier orbital [highest occupied molecular orbital (MO), lowest unoccupied MO] distribution in x, y, z-direction for c-NaNbO3 versus the distorted distribution in z-direction for o-NaNbO3. Pt-photodeposited layered HNb3O8 was superior to Pt-photodeposited layered KNb3O8 for CO2 photoreduction at 333 K (47). The methane formation rates were improved to 3.8 μmol h−1 gcat−1 when the moisture pressure increased from 12 to 25 In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

20 kPa and also SiO2 pillared between the layers of HNb3O8 (Table 3). However, not O2 or H2 was detected in the study, suggesting incomplete photocatalytic cycle. For InNbO4, the doping of NiO (0.5%) or Co3O4 (1.0%) slightly promoted the methanol photoformation (1.6–1.5 μmol h−1 gcat−1) from CO2 compared to unpromoted one (1.4 μmol h−1 gcat−1; Table 3) (48).

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

4.2.4 C-Containing Compounds o-NaNbO3 nanowire was combined with polymeric g-C3N4 (49). Methane was photogenerated using Pt-g-C3N4/NaNbO3 at a rate of 6.4 μmol h−1 gcat−1 higher by a factor of 8 compard to that using Pt-g-C3N4 (Table 3). Pt-o-NaNbO3 was inert in the conditions. The advantage of Pt-g-C3N4/NaNbO3 was ascribed to the chage separation at the heterojunction of p-type g-C3N4 to attract holes and n-type NaNbO3 to attract excited electrons. g-C3N4 was also combined with ZnO (50) and red-P (51) to form heterojunction and converted CO2 into major CO and major methane at rates of 29 and 300 μmol h−1 gcat−1, respectively. The reason of quite high methane formation rate using red-P-g-C3N4 is unclear and control reaction tests are needed. The disadvantages, low electric conductivity and rapid recombination of photogenerated electrons and holes, of 2-dimensional(D) g-C3N4 for photocatalysis were solved by assembling graphene with g-C3N4 (52). The electrons at N 2p was photoexcited to C 2p (CB: −1.42 V versus SHE) in g-C3N4 and could move to conducting network graphene (Fermi level: −0.08 V versus SHE). Thus, CO2 photoreduction rate into methane was boosted from 0.26 μmol h−1 gcat−1 (g-C3N4) to 0.59 μmol h−1 gcat−1 for graphene (15 wt%)-g-C3N4 assembly (Table 3). Cu2O assembled with 0.5 wt% of reduced graphene oxide (RGO) was also reported. CO was produced from CO2 and water at a rate of 0.43 μmol h−1 gcat−1 (Table 3) (53). Similar to reference 44, negative potential of CB for Cu2O (−1.44 V versus SHE, pH 0) should be advantageous for electron donation toward CO2derived species. A part of Ag+ of AgBr/carbon nanotube (CNT) was photoreduced to form Ag/AgBr/CNT (54). The photocatalyst was immersed in weak alkaline solution pressurized with 7.5 MPa of CO2. Methane, methanol, and CO were formed at a total formation rate of 56 μmol h−1 gcat−1 (Table 3). Longer CNT was preferable than shorter one probably due to better charge separation efficiency.

Photon Energy Conversion of CO2 to Fuels with Hydrogen or Sacrificial Reducing Agents 1. Photon Energy Conversion of CO2 to Fuels with Hydrogen If oxidation of water produces O2, protons, and electrons, utilizing natural light, photon energy conversion of CO2 to fuels with hydrogen (H atom equivalent to a proton and an electron) is also important as a latter half cycle of artificial photosynthesis (4). 26 In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

By the irradiation of deep UV light at 185 nm from Hg lamp and using synthetic quartz windows for the reactor, CO2 (9.6 kPa) was converted into major CH4 and minor CO with H2 (45 kPa) at a rate of 4.5 μmol h−1 for 82 h in the absence of catalyst (Table 4) (30). This rate was faster than the photolysis of CO2 with water (see Photon energy conversion of CO2 to fuels with water, section 4.1.1; Table 3). Light of 185 nm was confirmed to be responsible for the photolysis of CO2 rather than light of 254 nm from the Hg lamp. High conversion of CO2 with H2 was reported using Ni/SiO2-Al2O3 in similar reactor to Figure 7 at a methane formation rate of 55 mmol h−1 gcat−1 (Table 4) (55). By the effects of high-power solar simulator and heat of reaction for CO2 hydrogenation to methane (165 kJ mol−1), the temperature reached 423 K and gas pressure would be some hundreds kPa. Control experiment at 453 K in dark formed methane at significantly lower rate of 8.9 μmol h−1 gcat−1. Thus, the photocatalytic reduction was photoactivated and accompanied by thermal catalytic step(s). Ni/SiO2-Al2O3 when UV light was filtered showed similar activity to NiO irradiated by UV-visible light (13 mmol h−1 gcat−1; Table 4). The performance irradiated under UV-visible light was in the order

Scheme 2. Proposed reaction mechanism of photocatalytic CO2 reduction with H2 presumably assisted by later thermal catalytic step(s) using Ni/SiO2-Al2O3 (55). Reproduced from reference listing (55). Copyright 2014, ACS.

It was difficult to find the direct relationship between the reactivity and BG values or the conduction band level. Instead, formation of active Ni–H species was proposed by reducing/oxidizing H2 to H−/H+ and reacting with Ni+/Ni−, respectively (Scheme 2) (55).

27 In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Reactants

Photocatalyst Brand name

Amount (mg)

CO2

H2

T (K)

Light source

Reactor

Major product {formation rate (μmol h−1 gcat−1)}

Ref

No catalyst

–—

9.6 kPa

45 kPa

338 K

Hg (185, 254 nm)

Quartz

CH4 (4.5a)

(30)

Ni/SiO2-Al2O3

250

3.7 mmol

17 mmol

420 nm)

Aluminum

NiO Zn3Ga|CO3 LDH

100

2.3 kPa

21.7 kPa

420 nm)

CO (2400)

(69)

Atmosph. P

TEA (1 mL)

278

300 W Xe (λ > 420 nm)

CH3OH

(70)

CH3OH

(70)

CH3OH (39)

(71)

CH3OH (79)

(71)

Al–Cuporphyrin MOF GO

100

TEA (10 mL)

20 W white cold LED

Borosil

CoPc-GO

In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

Photon Energy Conversion of CO2 to Fuels Using Combination System with Photooxidation Catalysts Although the homogeneous photocatalysts and enzymes for CO2 reduction are out of scope of this chapter that is limiting to semiconductor photocatalysts, several studies were reported/reviewed to combine homogeneous complex or enzyme for CO2 photoreduction with semiconductor photocatalyst, e.g. Ru bpy-like complex with Ag/TaON (72, 73). The phenomena of photocatalytic oxidation of water and photocatalytic reduction of CO2 were combined using a cell (Figure 9A), in which the two photocatalysts, WO3 and [Zn1.5Cu1.5Ga(OH)8]2[Cu(OH)4]·mH2O LDH, were separated by a polymer electrolyte (PE) film (Figure 9B) (16). WO3 was used for the photooxidation of water, whereas Zn–Cu–Ga LDH was used for the photoreduction of CO2. Protons and electrons, which were formed on WO3 under the flow of moisture (solid–gas interface mode; Figure 9B), were used on Zn–Cu–Ga LDH instead of reactant H2 in Photon energy conversion of CO2 to fuels with hydrogen or sacrificial reducing agent, section 1 (56–58, 60). For this process, photocatalysts pressed on both sides of the PE film were irradiated by UV–visible light through quartz windows and through the space in carbon electrode plates set for both gas flow and light transmission. Methanol was the major product on LDH at a formation rate of 0.045 μmol h−1 gcat−1 under the flow of CO2 (Table 6). This rate accounted for 68–100% of photocurrents between the two redox photoelectrodes. In comparison, liquid-type another cell, which consisted of WO3 and LDH immersed in acidic solutions, with the PE film distinguishing the two compartments was reported (Figure 9C). The photocurrent from LDH to WO3 was increased by 2.4–3.4 times in comparison to gas–solid mode cell (Figure 9B) tested under similar conditions. However, major product from LDH was H2 at a formation rate of 0.67 μmol h−1 gcat−1. The difference of phase of water (moisture in panel B, liquid in panel C; Figure 9) directed the selectivity to methanol (equation 12) versus H2 (equation 13) (16). This trend of phase difference was in consistent with that found for metal-loaded TiO2 (Photon energy conversion of CO2 to fuels with water, section 2.1) (15).

Using a similar tandem twin reactor separated by PE film, CO2 conversion to methanol was also reported at rates of 1.6–1.8 μmol h−1 gcat−1 using WO3 on photoanode and Pt(1 wt%)-CuAlGaO4 and/or Pt(0.8 %)-SrTiO3:Rh on photocathode (74). A clear difference to reference 16 was the photocatalysts were not mounted on electrode and redox mediator (Fe3+ in anode and Fe2+ in cathode) was used. However, it is not certain whether electrons or Fe2+ would transfer through the PE film. 36 In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

Figure 9. The reaction path in photofuel cell (A), cell-1 to flow moisture to WO3 (B, front) and to circulate CO2 to LDH (B, back), and cell-2 to flow N2 to WO3 (C, right) and CO2 to LDH (C, left) immersed in HCl solutions (16). Reproduced from reference listing (16). Copyright, 2014, The Royal Society of Chemistry.

37 In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

38

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

Table 6. Reported CO2 Photoreduction Catalysts, Reaction Conditions, and the Formation Rates Combined with Photooxidation Catalysts Reactants

Photocatalyst Brand name

CO2

H2O

95

(Ne/N2)

Satur. P

45

3.5 kPa

300

(Ar)

225 mL (Fe3+: 2mM)

300

Saturated

(Fe2+: 2mM)

Amount (mg)

T (K)

Light source

Reactor

< 315

500 W Xe arc

PEFC

Major product {formation rate (μmol h−1 gcat−1)}

Ref

anode: WO3

(16)

cathode: Zn1.5Cu1.5Ga|Cu(OH)4

CH3OH (0.045)

anode: WO3

300 W Xe

Twin R separated by PE

(74)

cathode: Pt(1 %)-CuAlGaO4

CH3OH (1.8)

anode: WO3

300

(74)

cathode: Pt(1 %)-CuAlGaO4,

150

Pt(0.8 %)-SrTiO3:Rh

150

CH3OH (1.6)

In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

Concluding Remarks Recent advances in photocatalytic CO2 conversion with water and/or other reductants in these three years were reviewed in comparison to classic studied prior to 2012 (4) using TiO2 (75–81), ZnO (81), CdS (81), GaP (81), SiC (81), WO3 (81), Zn2GeO4 (82), Bi2WO6 (83), HNb3O8 (84), CuGa1−xFexO2 (85), AIILa4Ti4O15 (86), [Zn1.5Cu1.5Ga(OH)8]2CO3·mH2O (56, 60), ZrO2 (87), GaP (81, 88), GaAs (88, 89), and InP (89). Starting from CO2 and water, methane or CO formation using TiO2 was improved to 0.1–17 μmol h−1 gcat−1 by choosing approperiate crystalline phase (brookite or anatase), crystalline face, and the defects. Metals, e.g. Pt, Pd, Au, Rh, Ag, Ni, Cu, Au3Cu alloy, I, MgO, RuO2, graphene, g-C3N4, Cu-containing dyes, and Cu-containing MOFs were effective to assist TiO2 to form methane, CO, methanol, or ethane at rates of 1.4–160 μmol h−1 gcat−1 and further to 32–2200 μmol h−1 gcat−1 if minimal thin photocatalyst film was well deposited. Semiconductors, e.g. ZnO, Zn6Ti LDH, Mg3In LDH, KTaO3, graphene, GO, g-C3N4, CoTe, TiO2-coated p-GaP, Zn2SnO4, ZnO, ZnTe, SrTiO3, ZnGa2O4, Zn2GeO4, Zr–Co–Ir oxides, Nb2O5, HNbO3, NaNbO3, KNb3O8, InNbO4, NiO, Co3O4, Cu2O, and their assemblies were effective to photogenerate methane, CO, methanol, acetaldehyde at rates of 0.15–300 μmol h−1 gcat−1 in good competition with promoted TiO2. If H2 was used, new photoactivation of CO2 followed by thermal assisted reaction(s) was reported using Ni/SiO2-Al2O3 to produce methane at 423 K under pressurized CO2 + H2 at a rate of 55 mmol h−1 gcat−1 presumably via Ni–H species. As pure photocatalytic reaction, methanol formation rates were improved up to 0.30 μmol h−1 gcat−1 by the doping of Ag/Au nanoparticles, [Cu(OH)4]2− anions, and Cu-containing dyes to Zn–Ga LDH. The combination of two semiconductors (WO3, Zn–Cu–Ga LDH) were reported to from methanol at a rate of 0.05 μmol h−1 gcat−1 from CO2 and gaseous water. In this chapter, the improvement of CO2 conversion and new materials for the photoreduction were focused, and the importance of wavelength (deep UV, UV, and visible light) and flux of incident light, temperature, and form (powder, nanofiber, and/or film) of photocatalysts, pressure of reactants, were critical to determine the photoconversion of CO2 for the stage of new energy application levels. To enable the optimum reaction and photocatalyst conditions, the importance of reactor cell (30, 55) was also suggested. However, reaction mechanisms of CO2 activation, e.g. via glyoxal (9), via O-defect to form CO (equations 3–5) (10), multiple-step formaldehyde pathway (5), mutiple-step carbene pathway (5, 27), via metal–H active species (55), and via hydrogen carbonate (bicarbonate) (56, 61), are still in debate. To clarify the mechanism and responsible sites, spectroscopic studies, e.g. FTIR (27, 45, 61, 67, 70), diffuse reflectance infrared Fourier transform (10), electron paramagnetic resonance (9, 67), FE-SEM (22, 26, 49, 57), HR-TEM (20, 26, 27, 46, 47, 49, 54), photoluminescence (15), action (in-profile) spectrum (55, 57, 58), time-resolved TA (26, 29, 55), valence X-ray photoelectron (35, 39, 49), XANES (57, 61), EXAFS (90), and density functional theory calculations (9, 13, 29, 34, 46) are inevitable. 39 In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Acknowledgments

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

The authors are grateful for the financial supports from the Grant-in-Aid for Scientific Research C (26410204, 22550117) from Japan Science Promotion Agency, the Feasibility Study Stage of A-STEP (Proposal Nos. AS262Z00159L, AS251Z00906L, AS231Z01459C) from the Japan Science and Technology Agency, the Iwatani Naoji Foundation, Asahi Glass Foundation, the Promotion Section of Technology Innovation, Daikin Industries, and approval of the Photon Factory Proposal Review Committee for X-ray measurements (2014G631, 2011G033, 2009G552) for research related to this chapter.

References 1.

Lewis, N.; Nocera, D. G. Powering the Planet: Chemical Challenges in Solar Energy Utilization. Proc. Nat. Acad. Sci. 2006, 103, 15729–15735. 2. Bolton, J. R. Solar Photoproduction of Hydrogen: A Review. Solar Ener. 1996, 57, 37–50. 3. Aresta, M.; Dibenedetto, A.; Angelini, A. Catalysis for the Valorization of Exhaust Carbon: from CO2 to Chemicals, Materials, and Fuels. Technological Use of CO2. Chem. Rev. 2014, 114, 1709–1742. 4. Izumi, Y. Recent Advances in the Photocatalytic Conversion of Carbon Dioxide to Fuels with Water and/or Hydrogen Using Solar Energy and Beyond. Coord. Chem. Rev. 2013, 257, 171–186. 5. Habisreutinger, S. N.; Schmidt-Mende, L.; Stolarczyk, J. K. Photocatalytic Reduction of CO2 on TiO2 and Other Semiconductors. Angew. Chem., Int. Ed. 2013, 52, 7372–7408. 6. Smestad, G. P.; Steinfeld, A. Review: Photochemical and Thermochemical Production of Solar Fuels from H2O and CO2 Using Metal Oxide Catalysts. Ind. Eng. Chem. Res. 2012, 51, 11828–11840. 7. Roy, S. C.; Varghese, O. K.; Paulose, M.; Grimes, C. A. Toward Solar Fuels: Photocatalytic Conversion of Carbon Dioxide to Hydrocarbons. ACS Nano 2010, 4, 1259–1278. 8. Indrakanti, V. P.; Kubicki, J. D.; Schobert, H. H. Photoinduced Activation of CO2 on Ti-based Heterogeneous Catalysts: Current State, Chemical Physicsbased Insights and Outlook. Ener. Environ. Sci. 2009, 2, 745–758. 9. Dimitrijevic, N. M.; Vijayan, B. K.; Poluektov, O. G.; Rajh, T.; Gray, K. A.; He, H.; Zapol, P. Role of Water and Carbonates in Photocatalytic Transformation of CO2 to CH4 on Titania. J. Am. Chem. Soc. 2011, 133, 3964–3971. 10. Liu, L.; Zhao, H.; Andino, J. M.; Li, Y. Photocatalytic CO2 Reduction with H2O on TiO2 Nanocrystals: Comparison of Anatase, Rutile, and Brookite Polymorphs and Exploration of Surface Chemistry. ACS Catal. 2012, 2, 1817–1828. 11. Zhao, H.; Liu, L.; Andino; Li, Y. Bicrystalline TiO2 with Controllable anatase–Brookite Phase Content for Enhanced CO2 Photoreduction to Fuels. J. Mater. Chem. A 2013, 1, 8209–8216. 40 In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

12. Ye, L.; Mao, J.; Peng, T.; Zan, L.; Zhang, Y. Opposite Photocatalytic Activity Orders of Low-Index Facets of Anatase TiO2 for Liquid Phase Dye Degradation and Gaseous Phase CO2 Photoreduction. Phys. Chem. Chem. Phys. 2014, 16, 15675–15680. 13. Yu, J.; Low, J.; Xiao, W.; Zhou, P.; Jaroniec, M. Enhanced Photocatalytic CO2-Reduction Activity of Anatase TiO2 by Coexposed {001} and {101} Facets. J. Am. Chem. Soc. 2014, 136, 8839–8842. 14. Jiao, W.; Wang, L.; Liu, G.; Lu, G. Q.; Cheng, H. M. Hollow Anatase TiO2 Single Crystals and Mesocrystals with Dominant {101} Facets for Improved Photocatalysis Activity and Tuned Reaction Preference. ACS Catal. 2012, 2, 1854–1859. 15. Xie, S.; Wang, Y.; Zhang, Q.; Deng, W.; Wang, Y. MgO- and Pt-Promoted TiO2 as an Efficient Photocatalyst for the Preferential Reduction of Carbon Dioxide in the Presence of Water. ACS Catal. 2014, 4, 3644–3653. 16. Morikawa, M.; Ogura, Y.; Ahmed, N.; Kawamura, S.; Mikami, G.; Okamoto, S.; Izumi, Y. Photocatalytic Conversion of Carbon Dioxide into Methanol in Reverse Fuel Cells with Tungsten Oxide and Layered Double Hydroxide Photocatalysts for Solar Fuel Generation. Catal. Sci. Technol. 2014, 4, 1644–1651. 17. Weast, R. C. CRC Handbook of Chemistry and Physics; CRC Press: Boca Raton, FL, 2001; vol. 82; pp 12−130. 18. Kwak, B. S.; Vignesh, K.; Park, N. K.; Ryu, H. J.; Baek, J. I.; Kang, M. Methane Formation from Photoreduction of CO2 with Water Using TiO2 Including Ni Ingredient. Fuel 2015, 143, 570–576. 19. Ola, O.; Maroto-Valer, M. M. Role of Catalyst Carriers in CO2 Photoreduction over Nanocrystalline Nickel Loaded TiO2-based Photocatalysts. J. Catal. 2014, 309, 300–308. 20. Zhang, Z.; Wang, Z.; Cao, S. W.; Xue, C. Au/Pt Nanoparticle-Decorated TiO2 Nanofibers with Plasmon-Enhanced Photocatalytic Activities for Solar-toFuel Conversion. J. Phys. Chem. C 2013, 117, 25939–25947. 21. Zhang, Q.; Gao, T.; Andino, J. M.; Lio, Y. Copper and Iodine Co-modified TiO2 nanoparticles for Improved Activity of CO2 Photoreduction with Water Vapor. Appl. Catal. B 2012, 123/124, 257–264. 22. Zhang, X.; Han, F.; Shi, B.; Farsinezhad, S.; Dechaine, G. P.; Shankar, K. Photocatalytic Conversion of Diluted CO2 into Light Hydrocarbons Using Periodically Modulated Multiwalled Nanotube Arrays. Angew. Chem., Int. Ed. 2012, 51, 12732–12735. 23. Tu, W.; Zhou, Y.; Liu, Q.; Yan, S.; Bao, S.; Wang, X.; Xiao, M.; Zou, Z. An In Situ Simultaneous Reduction-Hydrolysis Technique for Fabrication of TiO2-Graphene 2D Sandwich-Like Hybrid Nanosheet: Graphene-Promoted Selectivity of Photocatalytic-Driven Hydrogenation and Coupling of CO2 into Methane and Ethane. Adv. Funct. Mater. 2013, 23, 1743–1749. 24. Tu, W.; Zhou, Y.; Liu, Q.; Tian, Z.; Gao, J.; Chen, X.; Zhang, H.; Liu, J.; Zou, Z. Robust Hollow Spheres Consisting of Alternating Titania Nanosheets and Graphene Nanosheets with High Photocatalytic Activity for CO2 Conversion into Renewable Fuels. Adv. Func. Mater. 2012, 22, 1215–1221. 41 In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

25. Zhou, S.; Liu, Y.; Li, J.; Wang, Y.; Jiang, G.; Zhao, Z.; Wang, D.; Duan, A.; Liu, J.; Wei, Y. Facile In Situ Synthesis of Graphitic Carbon Nitride (gC3N4)-N-TiO2 Heterojunction as an Efficient Photocatalyst for the Selective Photoreduction of CO2 to CO. Appl. Catal., B 2014, 158/159, 20–29. 26. Wang, W. N.; An, W. J.; Ramalingam, B.; Mukherjee, S.; Niedzwiedzki, D. M.; Gangopadhyay, S.; Biswas, P. Size and Structure Matter: Enhanced CO2 Photoreduction Efficiency by Size-Resolved Ultrafine Pt Nanoparticles on TiO2 Single Crystals. J. Am. Chem. Soc. 2012, 134, 11276–11281. 27. Neaţu, Ş.; Maciá-Agulló, J. A.; Concepción, P.; Garcia, H. Gold–Copper Nanoalloys Supported on TiO2 as Photocatalysts for CO2 Reduction by Water. J. Am. Chem. Soc. 2014, 136, 15969–15976. 28. Yuan, Y. J.; Yu, Z. T.; Zhang, J. Y.; Zou, Z. G. A Copper(I) Dye-Sensitised TiO2-Based System for Efficient Light Harvesting and Photoconversion of CO2 into Hydrocarbon Fuel. Dalton Trans. 2012, 41, 9594–9597. 29. Li, R.; Hu, J.; Deng, M.; Wang, H.; Wang, X.; Hu, Y.; Jiang, H. L.; Jiang, J.; Zhang, Q.; Xie, Y.; Xiong, Y. Integration of an Inorganic Semiconductor with a Metal–Organic Framework: A Platform for Enhanced Gaseous Photocatalytic Reactions. Adv. Mater. 2014, 26, 4783–4788. 30. Sastre, F.; Corma, A.; García, H. 185 nm Photoreduction of CO2 to Methane by Water. Influence of the Presence of a Basic Catalyst. J. Am. Chem. Soc. 2012, 134, 14137–14141. 31. Teramura, K.; Iguchi, S.; Mizuno, Y.; Shishido, T.; Tanaka, T. Photocatalytic Conversion of CO2 in Water over Layered Double Hydroxides. Angew. Chem. Int. Ed. 2012, 51, 8008–8011. 32. Li, Z.; Zhou, Y.; Zhang, J.; Tu, W.; Liu, Q.; Yu, T.; Zou, Z. Hexagonal Nanoplate-Textured Micro-Octahedron Zn2SnO4: Combined Effects toward Enhanced Efficiencies of Dye-Sensitized Solar Cell and Photoreduction of CO2 into Hydrocarbon Fuels. Crys. Growth Des. 2012, 12, 1476–1481. 33. Li, K.; Handoko, A. D.; Khraisheh, M.; Tang, J. Photocatalytic Reduction of CO2 and Protons Using Water as an Electron Donor over Potassium Tantalate Nanoflakes. Nanoscale 2014, 6, 9767–9773. 34. Guo, J.; Ouyang, S.; Kako, T.; Ye, J. Mesoporous In(OH)3 for Photoreduction of CO2 into Renewable Hydrocarbon Fuels. Appl. Surf. Sci. 2013, 280, 418–423. 35. Li, P.; Zhou, Y.; Tu, W.; Wang, R.; Zhang, C.; Liu, Q.; Li, H.; Li, Z.; Dai, H.; Wang, J.; Yan, S.; Zou, Z. Synthesis of Bi6Mo2O15 Sub-Microwires via a Molten Salt Method and Enhancing the Photocatalytic Reduction of CO2 into Solar Fuel through Tuning the Surface Oxide Vacancies by Simple PostHeating Treatment. Crys. Eng. Commun. 2013, 15, 9855–9858. 36. Hsu, H. C.; Shown, I.; Wei, H. Y.; Chang, Y. C.; Du, H. Y.; Lin, Y. G.; Tseng, C. A.; Wang, C. H.; Chen, L. C.; Lin, Y. C. Graphene Oxide as a Promising Photocatalyst for CO2 to Methanol Conversion. Nanoscale 2013, 5, 262–268. 37. Niu, P.; Yang, Y.; Yu, J. C.; Liu, G.; Cheng, H. M. Switching the Selectivity of the Photoreduction Reaction of Carbon Dioxide by Controlling the Band Structure of a g-C3N4 Photocatalyst. Chem. Commun. 2014, 50, 10837–10840. 42 In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

38. Khan, M. S.; Ashiq, M. N.; Ehsan, M. F.; He, T.; Ijaz, S. Controlled Synthesis of Cobalt Telluride Superstructures for the Visible Light Photo-conversion of Carbon Dioxide into Methane. Appl. Catal., A 2014, 487, 202–209. 39. Ehsan, M. F.; He, T. In Situ Synthesis of ZnO/ZnTe Common Cation Heterostructure and Its Visible-Light Photocatalytic Reduction of CO2 into CH4. Appl. Catal., B 2015, 166/167, 345–352. 40. Ehsan, M. F.; Ashiq, M. N.; Bi, F.; Palanisamy, S.; He, T. Preparation and Characterization of SrTiO3-ZnTe Nanocomposites for the Visible-Light Photoconversion of Carbon Dioxide to Methane. RSC Adv. 2014, 4, 48411–48418. 41. Yan, S.; Wang, J.; Gao, H.; Wang, N.; Yu, H.; Li, Z.; Zhou, Y.; Zou, Z. Zinc Gallogermanate Solid Solution: A Novel Photocatalyst for Efficiently Converting CO2 into Solar Fuels. Adv. Funct. Mater. 2013, 23, 1839–1845. 42. Blankenship, R. E.; Tiede, D. M.; Barber, J.; Brudvig, G. W.; Fleming, G.; Ghirardi, M.; Gunner, M. R.; Junge, W.; Kramer, D. M.; Melis, A.; Moore, T. A.; Moser, C. C.; Nocera, D. G.; Nozik, A. J.; Ort, D. R.; Parson, W. W.; Prince, R. C.; Sayre, R. T. Comparing Photosynthetic and Photovoltaic Efficiencies and Recognizing the Potential for Improvement. Science 2011, 332, 805–809. 43. Zeng, G.; Qiu, J.; Li, Z.; Pavaskar, P.; Cronin, S. B. CO2 Reduction to Methanol on TiO2-Passivated GaP Photoctalysts. ACS Catal. 2014, 4, 3512–3516. 44. Ghadimkhani, G.; de Tacconi, N. R.; Chanmanee, W.; Janaky, C.; Rajeshwar, K. Efficent Solar Photoelectrosynthesis of Methanol from Carbon Dioxide Using Hybrid CuO–Cu2O Semiconductor Nanorod Arrays. Chem. Commun. 2013, 49, 1297–1299. 45. Kim, W.; Yuan, G.; McClure, B. A.; Frei, H. Light Induced Carbon Dioxide Reduction by Water at Binuclear ZrOCoII Unit Coupled to Ir Oxide Nanocluster Catalyst. J. Am. Chem. Soc. 2014, 136, 11034–11042. 46. Li, P.; Ouyang, S.; Xi, G.; Kako, T.; Ye, J. The Effects of Crystal Structure and Electronic Structure on Photocatalytic H2 Evolution and CO2 Reduction over Two Phases of Perovskite-Structured NaNbO3. J. Phys. Chem. C 2012, 116, 7621–7628. 47. Li, X.; Li, W.; Zhuang, Z.; Zhong, Y.; Li, Q.; Wang, L. Photocatalytic Reduction of Carbon Dioxide to Methane over SiO2-Pillared HNb3O8. J. Phys. Chem. C 2012, 116, 16047–16053. 48. Lee, D. S.; Chen, H. J.; Chen, Y. W. Photocatalytic Reduction of Carbon Dioxide with Water Using InNbO4 Catalyst with NiO and Co3O4 Cocatalysts. J. Phys. Chem. Solid 2012, 73, 661–669. 49. Shi, H.; Chen, G.; Zhang, C.; Zou, Z. Polymeric g-C3N4 Coupled with NaNbO3 Nanowires toward Enhanced Photocatalytic Reduction of CO2 into Renewable Fuel. ACS Catal. 2014, 4, 3637–3643. 50. He, Y.; Wang, Y.; Zhang, L.; Teng, B.; Fan, M. High-Efficiency Conversion of CO2 to Fuel over ZnO/g-C3N4 Photocatalyst. Appl. Catal., B 2015, 168/ 169, 1–8.

43 In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

51. Yuan, Y. P.; Cao, S. W.; Liao, Y. S.; Yin, L. S.; Xue, C. Red Phosphor/gC3N4 Heterojunction with Enhanced Photocatalytic Activities for Solar Fuel Production. Appl. Catal., B 2013, 140/141, 164–168. 52. Ong, W. J.; Tan, L. L.; Chai, S. P.; Yong, S. T. Graphene Oxide as a Structure-Directing Agent for the Two-Dimensional Interface Engineering of Sandwich-Like Graphene–g-C3N4 Hybrid Nanostructures with Enhanced Visible-Light Photoreduction of CO2 to Methane. Chem. Commun. 2015, 51, 858–861. 53. An, X.; Li, K.; Tang, J. Cu2O/Reduced Graphene Oxide Composites for the Photocatalytic Conversion of CO2. ChemSusChem 2014, 7, 1086–1093. 54. Asi, M. A.; Zhu, L.; He, C.; Sharma, V. K.; Shu, D.; Li, S.; Yang, J.; Xiong, Y. Visible-Light-Harvesting Reduction of CO2 to Chemical Fuels with Plasmonic Ag@AgBr/CNT Nanocomposites. Catal. Today 2013, 216, 268–275. 55. Sastre, F.; Puga, A. V.; Liu, L.; Corma, A.; García, H. Complete Photocatalytic Reduction of CO2 to Methane by H2 under Solar Light Irradiation. J. Am. Chem. Soc. 2014, 136, 6798–6801. 56. Ahmed, N.; Shibata, Y.; Taniguchi, T.; Izumi, Y. Photocatalytic Conversion of Carbon Dixoide into Methanol Using Zinc–Copper–M(III) (M = Aluminum, Gallium) Layered Double Hydroxides. J. Catal. 2011, 279, 123–135. 57. Kawamura, S.; Puscasu, M. C.; Yoshida, Y.; Izumi, Y.; Carja, G. Tailoring Assemblies of Plasmonic Silver/Gold and Zinc–Gallium Layered Double Hydroxides for Photocatalytic Conversion of Carbon Dioxide Using UV–Visible Light. Appl. Catal. A 2015DOI:10.1016/apcata.2014.12.042. 58. Kawamura, S.; Ahmed, N.; Morikawa, M.; Mikami, G.; Carja, G.; Izumi, Y. Photocatalytic Conversion of Carbon Dioxide Using Zn–Cu–Al or Ga Layered Double Hydroxides: Cu in Contact with Gaseous Reactant is Needed for Methanol Generation. Oil Gas Sci. Technol. 2015May5in press. 59. Hou, W.; Cronin, S. B. A Review of Surface Plasmon Resonance-Enhanced Photocatalysis. Adv. Funct. Mater. 2013, 23, 1612–1619. 60. Ahmed, N.; Morikawa, M.; Izumi, Y. Photocatalytic Conversion of Carbon Dioxide into Methanol Using Optimized Layered Double Hydroxide Catalysts. Catal. Today 2012, 185, 263–269. 61. Morikawa, M.; Ahmed, N.; Yoshida, Y.; Izumi, Y. Photoconversion of Carbon Dioxide in Zinc–Copper–Gallium Layered Double Hydroxides: The Kinetics to Hydrogen Carbonate and Further to CO/Methanol. Appl. Catal., B 2014, 144, 561–569. 62. Izumi, Y.; Kawamura, S.; Morikawa, M.; Naveed, A. Monitoring of Electron Flow in Layered Double Hydroxides to Photoreduce Carbon Dioxide into Fuels; Photon Factory Activity Report 2013 (Highlights); 2014; Vol. 31A, pp 36−37. , 31A, 36–37. 63. Kang, Q.; Wang, T.; Li, P.; Liu, L.; Chang, K.; Li, M.; Ye, J. Photocatalytic Reduction of Carbon Dioxide by Hydrous Hydrazine over Au–Cu Alloy Nanoparticles Supported on SrTiO3/TiO2 Coaxial Nanotube Arrays. Angew. Chem. Int. Ed. 2015, 54, 841–845. 44 In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

64. Handoko, A. D.; Tang, J. Controllable Proton and CO2 Photoreduction over Cu2O with Various Morphologies. Int. J. Hydrogen Energy 2013, 38, 13017–13022. 65. Rossetti, I.; Villa, A.; Pirola, C.; Prati, L.; Ramis, G. A Novel High-Pressure Photoreactor for CO2 Photoconversion to Fuels. RSC Adv. 2014, 4, 28883–28885. 66. Chen, J.; Xin, F.; Yin, X.; Xiang, T.; Wang, Y. RSC Adv. 2015, 5, 3833–3839. 67. Wang, D.; Huang, R.; Liu, W.; Sun, D.; Li, Z. Fe-Based MOFs for Photocatalytic CO2 Reduction: Role of Coordination Unsaturated Sites and Dual Excitation Pathways. ACS Catal. 2014, 4, 4254–4260. 68. Liu, Q.; Low, Z. X.; Li, L.; Razmjou, A.; Wang, K.; Yao, J.; Wang, H. ZIF-8/Zn2GeO4 Nanorods with an Enhanced CO2 Adsorption Property in an Aqueous Medium for Photocatalytic Synthesis of Liquid Fuel. J. Mater. Chem. A 2013, 1, 11563–11569. 69. Wang, S.; Wang, X. Photocatalytic CO2 Reduction by CdS Promoted with a Zeolitic Imidazolate Framework. Appl. Catal., B 2015, 162, 494–500. 70. Liu, Y.; Yang, Y.; Sun, Q.; Wang, Z.; Huang, B.; Dai, Y.; Qin, X.; Zhang, X. Chemical Adsorption Enhanced CO2 Capture and Photoreduction over a Copper Porpyrin Based Metal Organic Framework. ACS Appl. Mater. Interfaces 2013, 5, 7654–7658. 71. Kumar, P.; Kumar, A.; Sreedhar, B.; Sain, B.; Ray, S. S.; Jain, S. L. Cobalt Phthalocyanine Immobilized on Graphene Oxide: An Efficient Visible-Active Catalyst for the Photoreduction of Carbon Dixoide. Chem. Eur. J. 2014, 20, 6154–6161. 72. Sekizawa, K.; Maeda, K.; Domen, K.; Koide, K.; Ishitani, O. Artificial Z-Scheme Constructed with a Supramolecular Metal Complex asd Semiconductor for the Photocatalytic Reduction of CO2. J. Am. Chem. Soc. 2013, 135, 4596–4599. 73. Windle, C. D.; Perutz, R. N. Advances in Molecular Photocatalytic and Electrocatalytic CO2 Reduction. Coord. Chem. Rev. 2012, 256, 2562–2570. 74. Lee, W. H.; Liao, C. H.; Tsai, M. F.; Huang, C. W.; Wu, J. C. S. A Novel Twin Reactor for CO2 Photoreduction to Minic Artifial Photosynthesis. Appl. Catal., B 2013, 132/133, 445–451. 75. Yui, T.; Kan, A.; Saitoh, C.; Koide, K.; Ibusuki, T.; Ishitani, O. Photochemical Reduction of CO2 Using TiO2: Effects of Organic Adsorbates on TiO2 and Deposition of Pd onto TiO2. ACS Appl. Mater. Interfaces 2011, 3, 2594–2600. 76. Yang, C. C.; Yu, Y. H.; van der Linden, B.; Wu, J. C. S.; Mul, G. Artificial Photosynthesis over Crystalline TiO2-Based Catalysts: Fact or Fiction? J. Am. Chem. Soc. 2010, 132, 8398–8406. 77. Varghese, O. K.; Paulose, M.; LaTempa, T. J.; Grimes, C. A. High-Rate Solar Photocatalytic Conversion of CO2 and Water Vapor to Hydrocarbon Fuels. Nano Lett. 2009, 9, 731–737. 78. Tseng, I. H.; Chang, W. C.; Wu, J. C. S. Photoreduction of CO2 Using Sol-Gel Derived Titania and Titania-Supported Catalysts. Appl. Catal., B 2002, 37, 37–48. 45 In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.

Downloaded by 103.240.178.211 on September 26, 2015 | http://pubs.acs.org Publication Date (Web): September 11, 2015 | doi: 10.1021/bk-2015-1194.ch001

79. Kaneco, S.; Kurimoto, H.; Shimizu, Y.; Ohta, K.; Mizuno, T. Photocatalytic Reduction of CO2 Using TiO2 Powders in Supercritical Fluid CO2. Energy 1999, 24, 21–30. 80. Anpo, M; Yamashita, H.; Ichihashi, Y.; Fujii, Y.; Honda, M. Photocatalytic Reduction of CO2 with H2O on Titanium Oxides Anchored within Micropores of Zeolites: Effects of the Structure of the Active Sites and the Addition of Pt. J. Phys. Chem. B 1997, 101, 2632–2636. 81. Inoue, T.; Fujishima, A.; Konishi, S.; Honda, K. Photoelectrocatalytic Reduction of Carbon Dioxide in Aqueous Suspensions of Semiconductor Powders. Nature 1979, 277, 637–638. 82. Liu, Q.; Zhou, Y.; Kou, J.; Chen, X.; Tian, Z.; Gao, J.; Yan, S.; Zou, Z. High-Yield Synthesis of Ultralong and Ultrathin Zn2GeO4 Nanoribbons toward Improved Photocatalytic Reduction of CO2 into Renewable Hydrocarbon Fuel. J. Am. Chem. Soc. 2010, 132, 14385–14387. 83. Zhou, Y.; Tian, Z.; Zhao, Z.; Liu, Q.; Kou, J.; Chen, X.; Gao, J.; Yan, S.; Zou, Z. High-Yield Synthesis of Untrathin and Uniform Bi2WO6 Square Nanoplates Benefitting from Photocatalytic Reduction of CO2 into Renewable Hydrocarbon Fuel under Visible Light. ACS Appl. Mater. Interfaces 2011, 3, 3594–3601. 84. Li, X.; Pan, H.; Li, W.; Zhuang, Z. Photocatalytic Reduction of CO2 to Methane over HNb3O8 Nanobelts. Appl. Catal., A 2012, 413/414, 103–108. 85. Lekse, J. W.; Underwood, M. K.; Lewis, J. P.; Matranga, C. C. Synthesis, Characterization, Electronic Structure, and Photocatalytic Behavior of CuGaO2 and CuGa1-xFexO2 (x = 0.05, 0.10, 0.15, 0.20) Delafossites. J. Phys. Chem. C 2012, 116, 1865–1872. 86. Iizuka, K.; Wato, T.; Miseki, Y.; Saito, K.; Kudo, A. Photocatalytic Reduction of Carbon Dioxide over Ag Cocatalyst-Loaded ALa4Ti4O15 (A = Ca, Sr, and Ba) Using Water as a Reducing Reagent. J. Am. Chem. Soc. 2011, 133, 20863–20868. 87. Kohno, Y.; Tanaka, T.; Funabiki, T.; Yoshida, S. Photoreduction of Carbon Dioxide with Hydrogen over ZrO2. Chem. Commun. 1997, 841–842. 88. Aurian-Biajeni, B.; Halmann, M.; Manassen, J. Electrochemical Measurement on the Photoelectrochemical Reduction of Aqueous Carbon Dioxide on p-Gallium Phosphide and p-Gallium Arsenide Semiconductor Electrodes. Solar Energy Mater. 1983, 8, 425–440. 89. Canfield, D.; Frese, K. W., Jr Reduction of Carbon Dixoide to Methanol on n- and p-GaAs and p-InP. Effect of Crystal Face, Electrolyte and Current Density. J. Electrochem. Soc. 1983, 130, 1772–1773. 90. Izumi, Y.; Itoi, T.; Peng, S.; Oka, K.; Shibata, Y. Site Structure and Photocatalytic Role of Sulfur or Nitrogen-Doped Titanium Oxide with Uniform Mesopores under Visible Light. J. Phys. Chem. C 2009, 113, 6706–6718.

46 In Advances in CO2 Capture, Sequestration, and Conversion; He, et al.; ACS Symposium Series; American Chemical Society: Washington, DC, 2015.