Technoeconomic and Environmental Assessment for Design and

Jan 19, 2018 - Experiments employing different reaction conditions are performed to provide the necessary information for a conceptual process design ...
1 downloads 11 Views 1MB Size
Subscriber access provided by READING UNIV

Article

Technoeconomic and Environmental Assessment for Design and Optimization of Tetraethyl Orthosilicate Synthesis Process Thuy Thi Hong Nguyen, Norihisa Fukaya, Kazuhiko Sato, Jun-Chul Choi, and Sho Kataoka Ind. Eng. Chem. Res., Just Accepted Manuscript • DOI: 10.1021/acs.iecr.7b03895 • Publication Date (Web): 19 Jan 2018 Downloaded from http://pubs.acs.org on January 19, 2018

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Industrial & Engineering Chemistry Research is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

1

Technoeconomic and Environmental Assessment for Design and Optimization of Tetraethyl

2

Orthosilicate Synthesis Process

3

Thuy T. H. Nguyena*, Norihisa Fukayab, Kazuhiko Satob, Jun-Chul Choib, Sho Kataokaa*

4

a

5

Catalytic Chemistry, National Institute of Advanced Industrial Science and Technology, 1-1-1

6

Higashi, Tsukuba, Ibaraki 305-8565, Japan

7

[email protected], [email protected]

Research Institute for Chemical Process Technology and bInterdisciplinary Research Center for

8

9

Abstract

10

Biogenic silica has been considered as a potential feedstock for producing a variety of

11

silicon-containing products. A new synthesis pathway of tetraethyl orthosilicate from silica that is

12

contained in rice hull ash has been recently proposed. Requiring only one-step processing, it is

13

expected to offer advantages over conventional routes, which are derived from silicon metal. This

14

study aims to investigate the optimal synthesis conditions for which this new technology can

15

sustainably replace the conventional method. Experiments employing different reaction conditions

16

are performed to provide the necessary information for a conceptual process design and an economic

17

and environmental viability evaluation. The results obtained by comparison with a selected

18

conventional process show that, under the optimal synthesis conditions, the new process can

19

decrease the production cost and markedly reduce the high greenhouse gas emissions. The 1

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 2 of 32

20

competitiveness of the new process is further examined with a sensitivity analysis considering

21

fluctuations in key feedstock and utility prices and alternative sources of electricity supplied to the

22

conventional process. The new synthesis technology shows its high potential as a sustainable

23

alternative to the conventional one.

24

Keywords: ethyl orthosilicate, biogenic silica, rice hull ash, optimal synthesis condition, conceptual

25

process design, economic and environmental viability, competitiveness.

26

27

Introduction

28

Tetraethyl orthosilicate or tetraethoxysilane (TEOS) has wide applications as an insulator in the

29

electronic industry, as a crosslinking agent and binder in coating and painting industries, and as an

30

intermediate substance in the production of diverse catalysts and products in the chemical industry.

31

Conventionally, TEOS is produced via two routes: the reaction of tetrachlorosilane with ethanol and

32

that of metallurgical silicon (Simg) with ethanol. Both routes utilize the same raw material, Simg. In

33

the former route, tetrachlorosilane is first produced from Simg, and then it requires extensive

34

energy-consuming purification steps before being used in TEOS synthesis.

35

hydrogen chloride causes many problems related to equipment corrosion, occupational health risk

36

exposure, and environmental impact. Since the latter route involves only one synthesis step, it is

37

much simpler and greener than the former.3-6 In these two conventional routes, the input feedstock

38

Simg is the main factor that determines the economic and environmental performance of the entire 2

ACS Paragon Plus Environment

1,2

The release of

Page 3 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

39

production process. In practice, this is primarily produced via carbon-thermal reduction of

40

silica-containing sources, which requires a large amount of electricity (approximately up to 13,000

41

kWh/ton product7,8), thus producing excessive greenhouse gas (GHG) emissions.

42

Rice hull ash (RHA) contains a large fraction of silica (more than 95 wt.%). The direct combustion,

43

gasification or pyrolysis of rice hull, which is widely available at considerably large amounts9-10,

44

results in RHA. It can be obtained from Utilizing RHA for producing silicon-based materials has

45

attracted increasing attention.11-16 Recently, our group synthesized TEOS by directly reacting RHA

46

with ethanol.17-18 This study revealed that the high-energy-consuming step of the thermal reduction

47

of silica to silicon can be eliminated. With this substantial improvement, it is expected that TEOS can

48

be widely produced without requiring large quantities of electricity. Experiments have shown the

49

strong impact of the ethanol volume on the product yield. The use of excess ethanol promotes a high

50

yield of TEOS but requires a large amount of energy for ethanol recovery. Therefore, to promote a

51

greener TEOS synthesis route, the production process must be well designed and rigorously

52

evaluated.

53

This study focuses on the conceptual design and evaluation of the impact of synthesis conditions,

54

with respect to the molar ratio of raw materials and the economic and environmental viability of this

55

new synthesis route. Experiments are performed under different synthesis conditions, based on which

56

a new synthesis process is designed. Through an in-depth assessment and comparison with a selected

57

conventional synthesis process, considering both the production cost and the GHG emissions, 3

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

58

optimal synthesis conditions are proposed to maximize the benefits. The competitiveness of the new

59

process is further examined, considering fluctuations in feedstock and utility prices and different

60

power generation systems. These analyses can provide a good vision for the long-term

61

implementation of new TEOS synthesis technology.

62

Process Design and Simulation Models of TEOS Synthesis Routes

63

The process configurations of the new and conventional synthesis routes are designed and modeled

64

using process simulator Pro/II. While the new route uses biogenic silica included in RHA, the

65

conventional one uses metallurgical silicon as the main input feedstock. These processes consist of

66

the main processing units used for product synthesis, by-product separation, unreacted reactant

67

recovery, and product purification. Data of TEOS properties and vapor-liquid equilibrium of

68

TEOS19-23 containing output mixtures are collected and input to Pro/II library data, on the basis of

69

which parameters necessary for process simulation are calculated using the selected thermodynamic

70

model (NRTL). Heuristic knowledge is applied to optimize the considered processes. The parameters

71

such as difference in temperature of the hot and cold fluids of the heat exchangers and the number of

72

stages, reflux ratio and feed position of the distillation columns are rigorously considered for

73

minimizing the energy and capital costs of the main processing units.

74

These processes are designed to produce TEOS with a purity of 99.5 wt.% and capacity of 1,000

75

tons/year. They are described in detail in the following sections, and their main reactions are

76

summarized in Table 1. 4

ACS Paragon Plus Environment

Page 4 of 32

Page 5 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

77

Industrial & Engineering Chemistry Research

Base Case: Metallurgical Silicon Utilizing Process

78

As mentioned above, TEOS is synthesized via two pathways: direct and indirect reactions of Simg

79

(via tetrachlorosilane synthesis) with ethanol. The former route is free from hazardous waste and

80

employs only one stage reaction. In the latter route, the purification of TEOS requires extensive

81

energy consumption and releases hydrogen chloride, which make this process more costly and

82

environmentally unfriendly. 3-6As the former method is simpler, greener, and less energy-consuming,

83

it was selected for comparison with the new synthesis route.

84

In this conventional process, silica-containing resources such as quartz must be reduced to Simg

85

following Eq. 1. This reduction is performed in an electric furnace at about 2,173 K using a reducing

86

agent containing carbon, such as coke, charcoal, or wood chips. A detailed description of Simg

87

production is beyond the scope of this paper. More information can be found in the available

88

literature.7,8 The Simg produced is then used for TEOS synthesis.

89

Figure 1 shows the synthesis process of TEOS from Simg. This was designed using information

90

obtained from the available literature.3 Simg obtained from silica reduction is heated at a high

91

temperature (773–973 K) with cupric oxide in a calcinator (a). Stream 1 containing the activated Simg

92

is then mixed with excess ethanol in a mixer (b). The mixed stream 2 is directed to a heat exchanger

93

(c), where it receives heat transferred from the stream 5 output from reactor (e). Output stream 3 is

94

further heated to the desired temperature in heater (d). The resulting stream 4 is directed to a TEOS

95

synthesis reactor (e) operated at an elevated temperature (443–463 K) and autogenous pressure. The 5

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 6 of 32

96

product stream 5 output from the reactor is a mixture of TEOS and the by-products triethoxysilane

97

(TRES) and hydrogen produced via Eqs. 2 and 3. Through heat exchangers (c) and (f), this transfers

98

heat to streams 2 and 9. It is further cooled after passing through cooler (g). Output stream 8 is then

99

directed to gas separator (h) for hydrogen removal. The output from heat exchanger (f), stream 10,

100

had an elevated temperature. This is finally directed to a separation system, which consists of

101

unconverted ethanol recovery and product purification distillation columns. Unconverted ethanol

102

obtained from the top of column (i) is fed back into the process. This is mixed with the fresh input

103

raw materials for starting a new production. In column (j), TRES is obtained at the top and can be

104

used as an intermediate chemical for manufacturing other products. TEOS at the desired purity is

105

obtained at the bottom of the column.

106

SiO2 + C → Si + CO2

(1)

107

Si + 4C2H5OH → Si(OC2H5)4 + 2H2

(2)

108

Si + 3C2H5OH → HSi(OC2H5)3 + H2

(3)

109

New Process: Biogenic Silica (RHA) Utilizing Process

110

Experimental procedures reported in our previous studies17,18 are mimicked to obtain the reaction

111

information used for process design and simulation. Different reaction conditions (molar ratios of

112

input raw materials) are employed to investigate their impact on the process performance. The initial

113

feedstock used in this process is RHA, which is obtained from the incineration of rice hull at about

6

ACS Paragon Plus Environment

Page 7 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

114

Industrial & Engineering Chemistry Research

773 K18, the energy obtained from this process can be used for the generation of electricity.

115

Figure 2 shows the synthesis process of TEOS using RHA. In mixer (a), RHA is mixed with

116

excess anhydrous ethanol. Output stream 1 is then passed through heat exchanger (b), where its

117

temperature is increased by the heat transferred from the stream 4 output from reactor (d). In heater

118

(c), the temperature of stream 2 is further increased. The resulting stream 3 is then directed to reactor

119

(d). In this reactor, TEOS and by-products are synthesized following Eqs. 4 and 5 in the presence of a

120

suitable amount of potassium hydroxide at 513 K.

121

SiO2 + 4C2H5OH ↔ Si(OC2H5)4 + 2H2O

(4)

122

2Si(OC2H5)4 + H2O ↔ Si2O(OC2H5)6 + 2C2H5OH

(5)

123

As the reactions involved in this process are reversible, a high input volume of ethanol and

124

continuous removal of water are required to attain a high product yield. Experiments with different

125

ratios of biogenic silica to ethanol were performed to examine the impact of this ratio on the product

126

yield. Table 1 shows alternative ethanol input volumes, which result in considerable differences in

127

the yields of TEOS and the main by-product.

128

To remove water, molecular sieve (MS) 3A is used.18 As this cannot absorb water effectively at high

129

temperature, the stream 4 output from the reactor is cooled to 333 K after passing through heat

130

exchangers (b) and (e) and cooler (f). Output stream 7 is then passed through absorber (g), which is

131

packed with MS 3A for water removal. Stream 8, which is free of water, is warmed after passing

7

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 8 of 32

132

through heat exchanger (e). Output stream 9 is then directed to a separation system, in which

133

unconverted ethanol is recovered as the major product of column (h) and fed back into the process.

134

In column (i), TEOS is obtained as the major product.

135

Evaluation Indicators

136

The above TEOS synthesis processes are evaluated considering the following economic and

137

environmental indicators.

138

Production Cost

139

The PC is calculated as [24]. It is the sum of the following costs: PC =   +   +   .

140

(6)

141

The investment cost (Cinvestment) includes the costs of all the main processing units involved in the

142

synthesis processes, such as reactors, heaters, heat exchangers, and distillation columns. This

143

equipment is assessed using the data on mass and heat balances obtained from the process simulation.

144

Its costs are estimated using Guthrie correlation25, and adjusted using the Chemical Engineering

145

Plant Index 2016.26 The investment cost is depreciated over a period of 10 years using the straight

146

line method.

147

The operating cost (Coperation) includes the costs of raw materials and utilities input to the alternative

148

processes. This is calculated based on the market prices and the energy and mass balance data.

149

The entire PC also accounts for other types of costs (Cothers), such as maintenance, and labor and

150

property tax costs, the total of which is assumed to be 20% of the total operating cost. 8

ACS Paragon Plus Environment

Page 9 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

151

Greenhouse Gas (GHG) Emissions

152

Greenhouse gas emissions (CO2 equivalent) are calculated considering all sources of carbon dioxide,

153

methane, and nitrous oxide. These mainly originate from the production of raw materials and utilities

154

used by the considered processes. Thus, high consumption of raw materials and utilities results in

155

high GHG emissions.

156

CO = CO    + CO    .

(7)

157

A cradle-to-gate life-cycle assessment method is applied for assessing GHG emissions, considering

158

both the key raw material production and the target product synthesis stages.

159

Basic parameters used for evaluating economic and environmental performances are displayed in

160

Tables 2 and 3. For the base case process, the life-cycle inventory data and average market price

161

(2$/kg as of 2016) of silicon metal are updated for evaluation using the available literature.27-29 It is

162

widely available in many Asian countries and can be purchased quite cheaply, on average 0.1$/kg

163

(estimated as of 2016). In both processes, fossil-based ethanol is used, which is produced by the

164

hydration of ethylene obtained from crude oil cracking processes. Life-cycle GHG emissions data for

165

ethanol and its main utilities are primarily obtained from the JLCA database.30 The input raw

166

material RHA of the new process is the waste obtained from the combustion of rice hull, from which

167

bioenergy can be generated an used in replacement of the fossil-based. This helps mitigate a large

168

amount of GHG emissions, approximately 0.953 kg CO2 per kilo hull used.31 Rice hull is produced

169

associated with rice grains and disposed during the rice milling process. It has markedly low 9

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

170

economic value. Based on the economic allocation method proposed by Kasmaprapruet et al.(32),

171

rice hull production shares relatively small fraction (2%) of total GHG emissions of rice production

172

(2.93 kg CO2/kg rice). This amount is much smaller than the amount it can help mitigate. Thus, it can

173

be considered that the preparation of RHA has a negligible contribution to the global warming

174

potential.

175

The market prices of key raw material (RHA) and utilities have strong impact on the economic

176

performance of the new process. Thus, a sensitivity analysis on the changes of these prices is

177

performed to examine the economic competitiveness of the new process for a long-term of projection.

178

The production of the input raw material of the conventional process, Simg, requires a markedly large

179

amount of electricity. This electricity supply, which can be generated using both renewable and

180

fossil-based resources, has strong impact on the market price and GHG emissions profile of Simg.

181

Therefore, the impact of the changes of Simg market price and electricity derived resources are also

182

considered for comparing the economic and environmental performances of the conventional process

183

with the new one.

184

Results and Discussion

185

The considered process flowsheets shown in Figures 1 and 2 are simulated. The obtained data of

186

mass and energy balance are shown in Table 4. Based on the basic parameters and data of market

187

prices and GHG emissions shown in Tables 2 and 3, the production cost and GHG emissions of the

188

considered processes are evaluated. As stated above, in an attempt to optimize the reaction conditions 10

ACS Paragon Plus Environment

Page 10 of 32

Page 11 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

189

of the new process, different experiments were performed under different reaction conditions. As

190

shown in Table 1, alternatives (Alts.) 1, 2, 3, and 4, which are differentiated by the input molar ratio

191

of biogenic silica and ethanol, give different yields of main and by-products. These alternatives are

192

evaluated and compared with the base case to determine the optimal synthesis conditions of the new

193

process.

194

Production Cost

195

Figure 3 compares the PCs of the base case and the new process. Figure 4 depicts the contribution of

196

each cost element to the total operation and the investment costs of these processes.

197

The evaluation results clearly show that the raw material’s cost makes the dominant contribution to

198

the total operating cost of both processes. This is commonly found in commodity chemical

199

production processes. Primarily, the raw material’s cost is influenced by the market prices and

200

conversion ratios of the main and by-products of the feedstocks. This includes the costs of ethanol

201

and key feedstocks, Simg and RHA, used in the base case and the new process, respectively. In Table

202

1, the base case shows a high conversion to the main product but also a high loss to TRES of Simg.

203

The high price of Simg means that the base case has a markedly high raw material cost. Due to

204

utilizing the cheap raw material RHA, all alternatives of the new process have much lower raw

205

material costs than the base case.

206

The utility cost is mainly spent on product synthesis, ethanol recovery, and product purification. This

207

is the cost of the energy used to heat the input raw material mixture, recover unconverted reactant, 11

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

208

and purify the target product to the desired degree. Thus, besides the conversion ratio of key

209

feedstocks to main and by-products, the flow mass of the material employed in the processes is also

210

an important factor in determining the utility cost of the entire process. Supplied with a much lower

211

input volume of ethanol, the base case has much lower energy consumption for ethanol recovery than

212

all alternatives of the new process. As shown in Table 1, it has higher conversion to by-product,

213

resulting in higher energy costs for by-product separation or product purification.

214

In the new process, the operating cost demonstrates a considerable change along with changes in the

215

RHA and ethanol molar ratios employed. In these alternatives, excess ethanol is input to create a

216

preferable environment stimulating the forward and backward reactions of Eqs. 4 and 5, respectively.

217

The amount of ethanol used for TEOS synthesis follows the stoichiometric rules of these reactions.

218

Thus, the higher the input amount of ethanol, the higher the amount of energy required for its

219

recovery. As shown in Table 1, Alt. 1 has the highest yield and the lowest loss of TEOS due to a high

220

ethanol input flow rate. Thus, Alt. 1 has a lower raw material cost than the other alternatives.

221

However, this reduction is dominated by a marked increase in the ethanol recovery cost. Thus, Alt. 1

222

has the highest operating cost. Alt. 2 utilizes a higher input amount of ethanol; thus, its energy costs

223

for ethanol recovery are higher than for Alts. 3 and 4. Due to the high yield of TEOS and the low loss

224

of raw materials, Alt. 2 requires lower amounts of RHA and ethanol, resulting in a lower raw

225

material cost. To sum up, Alt. 2 has the lowest operating cost among the considered alternatives of

226

the new process. 12

ACS Paragon Plus Environment

Page 12 of 32

Page 13 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

227

The breakdown of the investment cost into three main sections clearly shows the contributions of the

228

product synthesis, ethanol recovery, and product purification sections to the total costs of these

229

processes. Detail investment cost of the main equipment included in these sections are shown in

230

Table 5. Besides the reactor, the product synthesis section includes the main equipment used for

231

preparing the raw materials such as heater and heat exchanger. The sizes of these pieces of

232

equipment primarily depend on their heat duty, while that of the reactor depends on the flow volume

233

of the raw material and residence time.25 The volume of the unconverted reactant and by-product

234

formed after the reaction, as well as the complexity of separating these substances from the target

235

product, strongly impacts the investment cost of the ethanol recovery and product purification

236

columns. As the result clearly shows, the investment costs of both processes are mainly determined

237

by the ethanol recovery and product synthesis sections. The higher the ethanol input volume, the

238

larger the equipment required for processing. Thus, the base case has a smaller investment cost than

239

all alternatives of the new process. In the new process, the rank of the alternatives is clearly reflected

240

by the ethanol volume used, with Alt. 1 as the highest and Alt. 4 as the lowest.

241

The total costs of operation and investment and other costs (i.e., labor cost, maintenance cost, and

242

property tax) clearly indicate the high economic competitiveness of the new process compared with

243

the base case. Among the considered alternatives, Alt. 2 brings the highest returns. Thus, its molar

244

ratios of RHA and ethanol can be proposed as the most suitable conditions for a direct synthesis of

245

TEOS. 13

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

246

Analysis of the Economic Competitiveness of the New Process for Long-Term Projection

247

The economic competitiveness of the best alternative of the new process (Alt. 2) is further examined

248

by considering the changes in the market prices of the key feedstocks and utilities.

249

The price of Simg used in the base case is the main factor that determines the economic performance

250

of this process. It is primarily influenced by the balance of supply and demand of this feedstock.

251

Besides, the sources of electricity supply also has strong impact on the market price of Simg.

252

Historical databases33 have shown wild fluctuations in the price of Simg, with a decrease from more

253

than 3$/kg in 2014 to 2$/kg in 2016. This drop led to a considerable decrease in the TEOS

254

production cost, which influenced the economic competitiveness of the new process. The key RHA

255

feedstock used in the new process is obtained as the by-product of a rice-hull-fired power plant. It is

256

available in large quantities in many countries and it can be used as a type of fertilizer or as an

257

additive in the cement and steel industries. Such competitive utilization can influence the market

258

price of RHA. In Asia, RHA can be purchased for 0.05–0.15$/kg.

259

As Figure 4 clearly shows, the entire consumption of utilities (mainly steam and heavy fuel oil used

260

for product synthesis, ethanol recovery, and product purification) contributes significantly to the total

261

PC of the new process (approximately 22%). In the base case, this represents quite a small fraction.

262

Therefore, the economic performance of the new process is expected to be more sensitive to changes

263

in the price of utilities, which are strongly correlated with the price of crude oil determined by

264

oil-exporting countries. 14

ACS Paragon Plus Environment

Page 14 of 32

Page 15 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

265

Figure 5 shows the influence of changes in key feedstock and utilities prices on the economic

266

performance of the base case and the new process. A minus value indicates a drop in the current

267

prices of feedstocks supplied to the two processes, and vice versa. The new process can economically

268

substitute for the conventional one, even if the current price of RHA rises by more than 150% or that

269

of Simg drops by less than 30%. The new process becomes uneconomical if the Simg price drops by

270

more than 40%. The new process promises to bring higher returns even if the current price of utilities

271

increases by up to 50%. As this requires a much higher energy supply than the base case, it cannot

272

economically substitute for the base case if the price of utilities rises to 75%.

273

The above analyses clearly show that the economic performance of the new process is more sensitive

274

to the utility cost than the cost of the RHA raw material. Its performance is expected to be

275

substantially improved by co-production of TEOS and electricity using a much cheaper raw material,

276

rice hull, which costs on average 0.03$/kg. In this integrated production process, RHA can be

277

directly obtained from rice hull incineration, which produces energy and can be used to generate

278

electricity or steam. The generated electricity can be sold to the national grid as a surplus, while the

279

produced steam can be fed back into the production process. Therefore, the total PC can be

280

remarkably reduced.

281

Greenhouse Gas (GHG) Emissions

282

As with the PC, GHG emissions are calculated based on mass and heat balances obtained from the

283

simulation of the processes. This indicator intrinsically correlated with the amount of raw materials 15

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

284

and utilities used in the processes, which was determined by the conversion ratio of the key

285

feedstocks to the main and by-products, the mass flow rates of materials, and the effort of purifying

286

the target product from the unconverted reactant and by-products.

287

As mentioned above, Simg is the main factor that determines both the economic and the

288

environmental performances of the base case. The production of Simg requires a vast supply of

289

electricity, approximately 13 kWh/kg. In Europe (i.e., Norway), hydropower is the main source27. In

290

other parts of the world where modest quantities of renewable energy are available, fossil fuels are

291

still the main resources. In Asia, a large proportion of Simg production originates from China, which

292

has an electric power industry that is primarily reliant on coal. Therefore, the contribution of the base

293

case to the global warming potential relies heavily on the source of electricity used to produce its key

294

feedstock. In the new process, as a source of biogenic silica, RHA is a by-product obtained from the

295

burning of rice hull for electricity generation. As stated above, GHG emissions from RHA production

296

can be considered negligible.

297

In this study, the environmental performance of the new process is compared with that of the base

298

case by considering the sources of electricity supplied to the latter. Life-cycle GHG emissions from

299

different power generation systems are obtained from the available literature34. Life-cycle inventory

300

data on Simg are used to calculate GHG emissions from Simg production using different sources of

301

electricity.

302

Figure 6 compares the GHG emissions of the base case and the new process. Clearly, the raw 16

ACS Paragon Plus Environment

Page 16 of 32

Page 17 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

303

material consumption makes a dominant contribution to the total CO2 emission of the base case. The

304

new process (except Alt. 1) can substantially reduce the GHG emissions by 34%, 26%, and 21%

305

when electricity derived from coal, fuel oil, and liquefied natural gas is used to produce Simg,

306

respectively. If these resources are replaced by renewable energy such as hydropower, wind power,

307

and photovoltaic power, the base case contributes slightly less to the global warming potential than

308

the new process.

309

In the new process, utility consumption is the major contributor in Alts. 1 and 2, in which ethanol

310

is used in large volumes. In Alts. 3 and 4, the low ethanol input volumes result in lower energy

311

requirements but high raw material consumption due to the high yield of by-product. For these

312

alternatives, raw material (mainly ethanol) consumption represents a major fraction of the total CO2

313

emission. Among these alternatives, Alt. 3 produces the lowest GHG emissions.

314

Conclusion

315

In this study, a direct synthesis of TEOS from biogenic silica contained in RHA was designed and

316

evaluated considering both economic and environmental indicators. Experiments were performed to

317

examine the impact of the molar ratios of the key raw material and ethanol on the yields of the main

318

and by-products. A large input volume of ethanol creates a favorable environment for stimulating the

319

target reactions but results in high energy as well as high equipment costs. A small input volume of

320

ethanol reduces these costs but increases the loss of raw materials due to the formation of large

321

amounts of by-product. By assessing the PCs and GHG emissions, the most sustainable conditions 17

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

322

for TEOS synthesis from biogenic silica could be determined.

323

Under current market conditions, the new process at the optimal conditions as of Alt. 2 attains

324

higher economic returns and much lower contribution to global warming potential. Approximately,

325

7% production cost and 34% GHG emissions can be reduced by substituting the new process for the

326

conventional one. The economic and environmental performances of the new process can be further

327

increased upon an effective use of by-product, e.g., converting DS to the target product TEOS

328

following the backward reaction of Eq. 5. This can substantially reduce raw material loss, and thus

329

entire production cost. Further experiments should be performed to investigate suitable reaction

330

conditions for optimizing this conversion.

331 332

Acknowledgements

333

The authors express special thanks to New Energy and Industrial Technology Development

334

Organization (NEDO) for providing financial support.

335

18

ACS Paragon Plus Environment

Page 18 of 32

Page 19 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

336

References

337

1

Croker, W. A.; Hug, D. L. Method of preparing ethyl silicate. US 4,393,230, 1983.

338

2

Kropfgans, F.; Rauleder, H.; Schork, R. Process for preparing alkoxysilanes. US 6,242,628

339

B1, 2001.

340

3

341

1984.

342

4

343

tetraalkoxysilanes. US 6,191,296 B1, 2001.

344

5

Emblem, G. H.; Das, A. K.; Jones, K. Manufacture of alkyl silicates. US 4,211,717, 1980.

345

6

Mallon, C. B. Process for the preparation of alkyl silicates. US 4,487,949, 1984.

346

7

Schei, A.; Tuset, J. K.; Tveit, H. Production of high silicon alloys. Tapir Forlag, Trondheim

347

Publisher, Norway, 1998.

348

8

349

https://minerals.usgs.gov/minerals/pubs/.

350

9

351

from rice industry as a source of renewable. Renew. Sust. Energy. Rev. 2012, 16, 3084– 3094.

352

10

353

Renew. Sust. Energy. Rev. 2016, 53, 1468-1485.

354

11

Mallon, C. B. Process for production of alkyl silicates from silicon metal. US 4,447,632,

Dittrich, U.; Steding, F.; Mueller, R. Continuous method of manufacturing chlorine-free

Jones, T. S. Silicon. U.S. Geological survey minerals yearbook, 2000. Available at:

Lim, J. S., Manan, Z. A., Alwi, S. R. W., Hashim, H. A review on utilisation of biomass

Pode, R. Potential applications of rice husk ash waste from rice husk biomass power plant.

Sun, L. Silicon-based materials from rice husks and their applications. Ind. Eng. Chem. Res. 19

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

355

2001, 40, 5861-5877.

356

12

357

wastewater treatment. Ind. Eng. Chem. Res. 2011, 50, 13589-13613.

358

13

359

and precipitated silicas from biogenic silicas. US 2013/0184483 A1, 2013.

360

14

361

syngas and silica-based nickel nanoparticles production. Ind. Eng. Chem. Res. 2015, 54, 8919-8928.

362

15

363

from rice husk ash for drug delivery. Ind. Eng. Chem. Res. 2015, 54, 949-956.

364

16

365

method using rice husk as raw material. J. Mater. Process Tech. 2003, 141, 351-356.

366

17

367

Choi, J. Synthesis of tetramethoxysilane from silica and methanol using carbon dioxide and an

368

organic dehydrating reagent. Chem. Lett. 2016, 45, 828-830.

369

18

370

Sato, K.; Choi, J. Direct Synthesis of Tetraalkoxysilane from Silica and Alcohol. New J. Chem. 2017,

371

2224-2226.

372

19

373

2008.

Ahmaruzzaman, M.; Gupta, V. K. Rice husk and its ash as low-cost adsorbents in water and

Laine, R. M.; Marchal, J. C.; Popova, V.; Krug, D. J. Method of producing alkoxysilanes

Shen, Y.; Ding, M.; Ge, X.; Chen, M. Catalytic CO2 gasification of rice husk char for

Rajanna, S. K.; Kumar, D.; Vinjamur, M.; Mukhopadhyay, M. Silica aerogel microparticles

Seo, E. S. M.; Andreoli, M.; Chiba, R. Silicon tetrachloride production by chlorination

Fukaya, N.; Choi, S. J.; Horikoshi, T.; Kumai, H.; Hasegawa, M.; Yasuda, H.; Sato, K.;

Fukaya, N.; Choi, S. J.; Horikoshi, T.; Kataoka, S.; Endo, A.; Kumai, H.; Hasegawa, M.;

Perry, R. H.; Green, D. W. Perry's chemical engineers' handbook. New York: McGraw-Hill,

20

ACS Paragon Plus Environment

Page 20 of 32

Page 21 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

374

20

Ivannikov, P. S.; Litvinenko, I. V.; Radchenko, I. V. Thermal Conductivity of

375

Tetramethoxysilane, Tetraethoxysilane, and Tetraethyl Tin. J. eng. phys. thermophys., 1975, 28,

376

63-66.

377

21

378

Compounds. J. Chem. Eng. Data, 1993, 38, 175-200.

379

22

380

Tetraethoxysilane (TEOS) and An Infrared Study of Its Thermal Decomposition. J. Phys. Colloq. IV,

381

1993, 3, 75-82.

382

23

383

Binary Systems: Methanol + Silicon Tetramethoxide, Methanol + Silicon Tetraethoxide, Ethanol +

384

Silicon Tetramethoxide, and Ethanol + Silicon Tetraethoxide. J. Chem. Eng. Data, 1989, 34,

385

206-209.

386

24

387

Assessment of Bio-based Chemical Processes Toward Sustainability. Ind. Eng. Chem. Res., 2015, 54,

388

5494-5504.

389

25

390

process design. Upper Saddle River, N.J: Prentice Hall PTR, 1997.

391

26

Chemical engineering magazine, 2016. Available at: http://www.chemengonline.com/.

392

27

Jungbluth, N.; Stucki, M.; Flury, K.; Frischknecht, R.; Büsser, S. Life cycle inventories of

Myers, K. H.; Danner, R. P. Prediction of Properties of Silicon, Boron, and Aluminum

Van Der Vis, M. G. M.; Cordfunke, E.; Konings, R. The Thermodynamic Properties of

Kato, M.; Tanaka, H. Ebulliometric Measurement of Vapor-Liquid Equilibria for Four

Nguyen, T. T. H.; Kikuchi, Y.; Noda, M.; Hirao, M. A New Approach for Design and

Biegler, L. T.; Grossmann, I. E.; Westerberg, A. W. Systematic methods of chemical

21

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 22 of 32

393

photovoltaics, Swiss Federal Office of Energy SFOE, 2012.

394

28

395

comparison of the Elkem Solar metallurgical route and conventional gas routes to solar silicon.

396

Proceedings of the 23rd European Photovoltaic Solar Energy Conference, Valencia, Spain, 1-5

397

September 2008.

398

29

399

Available at: https://minerals.usgs.gov/minerals/pubs/commodity/silicon/.

400

30

JLCA (Life Cycle Assessment Society of Japan), JLCA-LCA database 2nd edition, 2007.

401

31

Prasara-A, J., Grant, T. Comparative life cycle assessment of uses of rice husk for energy

402

purposes. Int. J. Life Cycle Assess., 2011, 16, 493–502.

403

32

404

assessment of milled rice production: Case study in Thailand. Eur. J. Sci. Res., 2009, 30, 195-203.

405

33

406

https://www.statista.com/statistics/301564/us-silicon-price-by-type/

407

34

408

Energy 2005, 30, 2042–2056.

De Wild-Scholten M. J., Gløckner R., Odden J. -O., Halvorsen G., Tronstad R. LCA

USGS National Minerals Information Center. Mineral industry survey November 2016.

Kasmaprapruet, S., Paengjuntuek, W., Saikhwan, P., Phungrassami, H., Life cycle

Statista.

The

statistics

portal.

Available

at:

Hondo, H. Life cycle GHG emission analysis of power generation systems: Japanese case.

409

22

ACS Paragon Plus Environment

Page 23 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47

410

Industrial & Engineering Chemistry Research

Table 1: Reaction conditions included in the base case and new synthesis routes Base case6

Alternative 1

Alternative 2

Alternative 3

Alternative 4

453

513

513

513

513

Key input component Molar ratio key component:ethanol

Silicon metal 1:23

Biogenic silica 1:112

Biogenic silica 1:57

Biogenic silica 1:37

Biogenic silica 1:28

Main by-product Conversion of key component (%) Yield of TEOS (%)

TRES 88.0

DS 96.9

DS 77.2

DS 82.0

DS 70.7

74.0

91.3

68.0

56.2

44.8

14.0

2.8

4.6

12.9

12.9

Process ID Temperature [K]

(key component-based) Yield of by-product (%) (key component-based) 411 412

23

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

413

Table 2: Basic parameters used for the evaluation of the PC Project life time

10 years

Working capital Labor

15% process capital cost 10% operating cost

Maintenance Supplies Property tax

6% process capital cost 2% process capital cost 3% process capital cost

Depreciation

Straight line

414 415

Table 3: Price and GHG emissions of main utilities and raw materials Price [$/kg]

GHG emissions [kg CO2/kg]

Ethanol

0.7*

1.6730

Silicon metal

2.0 29

Rice hull ash

0.10*

Depending on electricity sources 0.00

Steam

0.02*

0.1730

Fuel oil Cooling water (recycled)

0.35* 0.00

3.4630 0.00

Raw material

Utility

416

*Average estimated price as of 2016

417 418

24

ACS Paragon Plus Environment

Page 24 of 32

Page 25 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

419

Industrial & Engineering Chemistry Research

Table 4: Main input (kg/kg product) of base case and new process Raw material/ utility

Base case

New process Alternative 1

Alternative 2

Alternative 3

Alternative 4

Raw material (kg/kg TEOS) Silicon metal

0.16

-

-

-

-

Rice hull ash Ethanol

1.09

0.34 0.93

0.36 0.97

0.47 1.19

0.51 1.27

3.32

13.30

8.95

6.86

6.47

176.50 0.006

637.95 0.19

429.97 0.12

329.02 0.11

309.59 0.10

Utility (kg/kg TEOS) Steam Cooling water Fuel oil 420 421 422

Table 5: Estimated capital costs of main equipment of the base case and new process [$] Main equipment

Base case

New process Alternative 1

Alternative 2

Alternative 3

Alternative 4

Heat exchangers

73,676

197,637

153,136

129,928

125,397

Heater Cooler Reactor Distillation columns

4,586 26,029 89,053 416,216

18,557 20,628 828,207 1,138,851

18,378 15,044 653,902 928,617

20,004 12,365 562,193 797,170

20,473 11,863 546,725 769,492

Total

609,560

2,203,880

1,769,077

1,521,660

1,473,950

423 424

25

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

425

426

428

Figure 1: TEOS synthesis process from Simg (base case). (a) Calcinator; (b) mixer; (c, f) heat exchangers; (d) heater; (e) reactor; (g) cooler; (h) gas separator; (i) ethanol recovery column; (j)

429

TEOS purification column. ROH: anhydrous ethanol; RHA: rice hull ash; TEOS: ethyl orthosilicate;

430

TRES: triethoxysilane.

427

431

26

ACS Paragon Plus Environment

Page 26 of 32

Page 27 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

432 433

Industrial & Engineering Chemistry Research

434

Figure 2: TEOS synthesis process from RHA (new process). (a) Mixer; (b, e) heat exchangers; (c) heater; (d) reactor; (f) cooler; (g) water absorber; (h) ethanol recovery column; (i) TEOS purification

435

column. ROH: anhydrous ethanol; RHA: rice hull ash; TEOS: ethyl orthosilicate; DS:

436

hexaethyldisiloxane.

437

27

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

438 439

Figure 3: Comparison of economic performances of the base case and the new process (Alt.:

440

alternative molar ratios of RHA and ethanol of the new process; these are described in detail in Table

441

1).

442

28

ACS Paragon Plus Environment

Page 28 of 32

Page 29 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

443 444

Figure 4: Contribution of cost elements to the total operation and investment costs (left and

445

right columns indicate the contribution of cost elements to the operation and investment costs,

446

respectively).

447

29

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

448 449

Figure 5: Impact of the key raw materials and utilities prices on the economic competitiveness

450 451

of the new process. Solid and dotted lines indicate the impacts of key raw material (Simg for conventional and RHA for

452

new processes) and utilities prices, respectively. Circle and triangle marks refer to conventional and

453

new processes, respectively.

454 455

30

ACS Paragon Plus Environment

Page 30 of 32

Page 31 of 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Industrial & Engineering Chemistry Research

456

457 458

Figure 6: Comparison of GHG emissions.

459

CP: coal power; FP: fuel oil power; GP: liquefied natural gas power; NP: nuclear power, HP:

460

hydropower; WP: wind power; SP: solar-photovoltaic power.

31

ACS Paragon Plus Environment

Industrial & Engineering Chemistry Research 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41

Lab experiment SiO2 Silica in RHA

+ C2H5OH

Design and optimization

Si(OCH2CH3)4 Tetraethyl orthosilicate

Process assessment New process

ACS Paragon Plus Environment

Page 32 of 32