Water purification using functionalized cellulosic fibers with non

adsorbing cellulosic fibers, functionalized with polyelectrolytes according to the ... Point-of-use (POU) water treatments, i.e., portable water purif...
0 downloads 0 Views 2MB Size
Subscriber access provided by Binghamton University | Libraries

Article

Water purification using functionalized cellulosic fibers with non-leaching bacteria adsorbing properties Anna Elizabeth Ottenhall, Josefin Illergård, and Monica Kerstin Ek Environ. Sci. Technol., Just Accepted Manuscript • Publication Date (Web): 17 May 2017 Downloaded from http://pubs.acs.org on May 25, 2017

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

Environmental Science & Technology is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 22

Environmental Science & Technology

1 2

Graphic for TOC/Abstract art

3 4 5 6 7 8 9 10 11 12 13 14

Water purification using functionalized cellulosic fibers with non-leaching bacteria adsorbing properties Anna Ottenhall, Josefin Illergård and Monica Ek* Department of Fibre and Polymer Technology, School of Chemical Science and Engineering, KTH Royal Institute of Technology, Teknikringen 56-58, 114 28 Stockholm, Sweden Key words: Emergency treatment, contact-active material, Layer-by-Layer, polyelectrolyte

15

multilayer

16

ABSTRACT: Portable purification systems are easy ways to obtain clean drinking water when there

17

is no large-scale water treatment available. In this study, the potential to purify water using bacteria

18

adsorbing cellulosic fibers, functionalized with polyelectrolytes according to the Layer-by-Layer

19

method, is investigated. The adsorbed polyelectrolytes create a positive charge on the fiber surface

20

that physically attracts and bonds with bacteria. Three types of cellulosic materials have been

21

modified and tested for the bacterial removal capacity in water. The time, material-water ratio and

22

bacterial concentration dependence, as well as the bacterial removal capacity in water from natural

23

sources, have been evaluated. Freely dispersed bacteria adsorbing cellulosic fibers can remove

24

greater than 99.9 % of Escherichia coli from non-turbid water, with the most notable reduction

25

occurring within the first hour. A filtering approach using modified cellulosic fibers is desirable for

26

purification of natural water. An initial filtration test showed that polyelectrolyte multilayer

27

modified cellulosic fibers can remove greater than 99 % of bacteria from natural water. The bacteria

28

adsorbing cellulosic fibers do not leach any biocides, and it is an environmentally sustainable and

29

cheap option for disposable water purification devices.

ACS Paragon Plus Environment

1

Environmental Science & Technology

30 31 32 33 34 35 36 37

Page 2 of 22

INTRODUCTION Clean drinking water is one of the basic needs of survival, and the lack of safe drinking water is a

38

large global health issue. One of the ten most common causes of death globally is diarrheal diseases,

39

which are often caused by fecal bacteria such as Escherichia coli or Vibrio cholerae that are spread via

40

contaminated, non-treated drinking water.1 Effective sanitation systems and sterilization of drinking

41

water are essential for preventing water-borne diseases from spreading, especially because even

42

small doses of pathogen bacteria can lead to fatal diarrheal diseases.2

43 44

Point-of-use (POU) water treatments, i.e., portable water purification devices, are a way to obtain

45

safe drinking water when there is no large-scale water treatment infrastructure available, e.g., during

46

an emergency response or in remote areas.3, 4 There are a few different POU sterilization methods

47

utilized today, such as chlorination with or without a flocculation agent, ceramic membrane filters

48

and sterilization by sunlight. 5, 6 Although most methods are efficient at removing bacteria, they also

49

have drawbacks. In particular, disinfection by chlorine, which is the most common POU method, is

50

less efficient when water is turbid. In addition, chlorination of water with organic matter can result

51

in hazardous chlorinated carbon compounds that can have long term health effects.7 Another

52

important issue with chlorination is the taste of chlorine in the treated water, which makes it

53

unpleasant to drink.6 Ceramic membrane filters and sterilization by sunlight is time consuming and

54

can take several hours to obtain sufficient volumes of drinking water. The efficiency of sterilization

55

by sunlight can also be reduced if the water is too turbid.5 New methods and new approaches are

56

needed for easy, cheap and safe POU sterilization to complement the existing techniques.

57 58

Bacteria adsorbing cellulosic fibers are an interesting alternative to the currently available POU

59

methods since cellulose is a relatively cheap, lightweight and biodegradable material, which can be

60

incinerated or possibly composted after use to remove pathogenic bacteria. These are all important

61

properties when developing disposable devises for POU purification of water emergency situations.

62

Cellulose is the most abundant polymer on Earth and is mainly found in plant fibers, e.g., in wood,

ACS Paragon Plus Environment

2

Page 3 of 22

Environmental Science & Technology

63

and is used for making many of the products used on a daily basis, such as paper and textiles. A new

64

POU product has recently been launched on the market, Safe Water Book (Folia Water, Pittsburg,

65

PA, USA), which sterilizes drinking water by filtering it through a cellulosic filter infused with silver

66

nanoparticles that kill bacteria.8, 9 Similar to most commercially available antibacterial materials,

67

Safe Water Book utilizes the release of biocides to achieve the antibacterial effect, which is often

68

referred to as controlled-release surfaces.8-10 Although silver is an effective bactericide and sterilizes

69

water, it also has considerable drawbacks. Silver nanoparticles are dangerous for organisms that live

70

in water, and research has shown that fecal bacteria that are exposed to silver can develop a

71

resistance to silver and even antibiotics. 11-13,14, 15 Still, new concepts for POU sterilization methods

72

based on releasing silver ions or silver particles to kill bacteria in water are continuously developed.4,

73

6, 8, 16

74

mechanism, i.e., where the antibacterial functionality is permanently attached to the material

75

surface, which prevents leaching of the antibacterial agent into the water.10 Several studies have been

76

performed on contact-active bacteria adsorbing cellulosic fibers where the fibers have been

77

equipped with antibacterial agents.10, 17-19 One of the interesting modification techniques used to

78

achieve the bacteria adsorbing effect is to introduce a highly positive charged fiber surface via Layer-

79

by-Layer (LbL) modification. In this technique, charged polymers, polyelectrolytes are continually

80

absorbed to form polyelectrolyte multilayers on any charged surfaces to provide the desired

81

properties. 10, 20-22 The process is usually carried out in water and at room temperature, making it

82

more environmentally friendly than other cellulose modifications that covalently link polymers to

83

the fibers in organic solvents during harsh conditions.17 The bacteria adsorbing effect is commonly

84

achieved by having a highly positive charged polyelectrolyte in the final layer of the multilayer

85

modification. This creates a net positive surface charge that will attract and bond with bacteria upon

86

physical contact, as the cell envelope of both Gram-positive and Gram-negative bacteria has a

87

negative net charge. This makes the contact-active bacteria adsorbing cellulosic fibers efficient for

88

many different pathogens and prevents the bacteria from easily developing resistance to the contact-

89

active material.10, 23 A polymer that had previously been shown to possess excellent antibacterial

90

properties when applied on cellulosic fibers is polyvinylamine (PVAm). Illergård et al. showed it was

91

possible to achieve an antibacterial effect greater than 99.9 % on E. coli after 4 hours of incubation

92

by the use of treated cellulosic fibers while not leaching any polyelectrolytes.10, 17 Contact-active

A better alternative than releasing biocides would be to use materials with a contact-active

ACS Paragon Plus Environment

3

Environmental Science & Technology

93

bacteria adsorbing cellulosic fibers, generated by the LbL technique, could therefore be a better

94

alternative for water purification than using materials that leach biocides, both from an

95

environmental and a toxicological perspective.

Page 4 of 22

96 97

This article investigates the possibility of a novel method to purify bacterial contaminated water by

98

combining a non-leaching bacteria adsorbing modification, using polyelectrolyte multilayers, with

99

disposable cellulosic material and it is the first one to evaluate the bacterial removal efficiency of this

100

multilayer modification on natural water samples. These are the first steps towards developing a

101

disposable POU method for sustainable water purification in emergency situations.

102 103

EXPERIMENTAL METHODS

104

Materials and chemicals

105

Bleached chemical softwood pulp fibers (hereinafter referred to as cellulose fibers) were supplied by

106

SCA Hygiene Products (Mölndal, Sweden), and commercially available coffee filter paper

107

(hereinafter referred to as filter paper) made of bleached cellulosic fibers was obtained from

108

Klimabolaget AB (Staffanstorp, Sweden). Cationic polyvinylamine Lupamin 9095 was supplied by

109

BASF SE (Ludwigshafen, Germany) with a molecular weight of 340 kDa, and anionic polyacrylic acid

110

was obtained from Sigma-Aldrich (Stockholm, Sweden) with a reported molecular weight of 240

111

kDa. 2,2,6,6-Tetramethyl-1-piperidinyloxy (TEMPO) was obtained from Sigma-Aldrich (Stockholm,

112

Sweden). Filter paper from the POU purification device Safe Water Book (Folia Waters, Pittsburgh,

113

PA, USA) was used as a commercial reference.

114 115

Methods

116

Pretreatment with TEMPO-oxidation

117

TEMPO-oxidation, which occurs when the primary hydroxyl group in the glucose chain is oxidized

118

into carboxyl groups, was performed on a fraction of the fibers to increase the negative net charges

119

and thereby increase the polymer adsorption.24, 25 An scaled up version of Saito et al. TEMPO-

120

oxidation was used, in which 20.0 g of cellulose fibers were purified during constant stirring for 1

121

hour at 60°C in an acetate buffer solution at a pH of 4.6 and a NaClO2 concentration of 3.00 g/L.25

122

The cellulose fibers were rinsed in deionized water (dH2O) and thereafter oxidized over 4 hours at

ACS Paragon Plus Environment

4

Page 5 of 22

Environmental Science & Technology

123

60°C in a phosphate buffer solution at a pH of 6.8, containing 10.50 g/L NaClO2, 8.33 g/L NaClO and

124

0.17 g/L TEMPO. The oxidation reaction was terminated by rinsing the cellulose fibers in dH2O.

125

Polymer modification

126

Cellulose fibers, TEMPO-oxidized cellulose fibers (hereinafter referred to as TEMPO cellulose) and

127

filter paper were modified with three layers of polyelectrolytes using the LbL adsorption method.

128

The first and third final layers of polyelectrolytes were cationic PVAm, and anionic PAA was

129

adsorbed as the second middle layer. The polyelectrolyte adsorptions were performed at a 1 w/w %

130

material consistency in dH2O. The polyelectrolytes were adsorbed over 10 minutes in a 0.1 g/L

131

polymer solution with 100 mM NaCl added. The PVAm was adsorbed at a pH of 9.5 and the PAA was

132

adsorbed at a pH of 3.5. The material was thoroughly rinsed in dH2O between the adsorption steps.

133

To increase the available mobile charges of the final material, the pH of the modified material was

134

rinsed with dH2O set to a pH of 3.5.26 The cellulose fibers and TEMPO cellulose were thereafter

135

freeze-dried, while the filter paper was dried at ambient temperature.

136 137

Fiber size measurement

138

The size of the cellulose pulp fibers was determined to get an approximation of the average fiber

139

surface area. The length (l) and width (w) of the fibers were measured using L&W Fiber Tester Plus

140

(ABB Lorentzen &Wettre Products, Kista, Sweden) and the results were weighted against the fiber

141

area (A) according to Eq. 1 and 2.

142 143

=

∑  × ∑  

Eq. 1

144 145

=

∑  ×  ∑  

Eq. 2

146 147

Scanning electron microscopy

148

The morphology of the cellulosic materials was visualized by scanning electron microscope (SEM)

149

micrographs, using a S-4800 field emission scanning electron microscope (Hitachi, Tokyo, Japan).

150

The specimens were dried in a desiccator over night and sputtered with a platinum/palladium

ACS Paragon Plus Environment

5

Environmental Science & Technology

Page 6 of 22

151

coating using a 208HR high-resolution sputter coater (Cressington, Watford, United Kingdom) prior

152

to the SEM analysis to reduce specimen charging.

153 154

Nitrogen analysis

155

Nitrogen analysis was performed using ANTEK 700 nitrogen analyzer (Antek Instruments, Houston,

156

TX, USA) using 6 mg of material per measurement, and 6 measurements were performed for each

157

material. The amount of PVAm adsorbed to the materials can be estimated by measuring the

158

nitrogen content in comparison with the reference material, as the positively charged polymer is the

159

only nitrogen containing substance added in the modification process.

160

Bacterial reduction

161

Microbiology tests were performed with the non-pathogenic bacterial strain Escherichia coli ATCC

162

11775, obtained from SIK (Gothenburg, Sweden), as a model bacteria and the number of viable

163

bacteria in water was determined as colony-forming units (CFU) per mL. The bacterial reduction

164

capacity of the material was tested and duplicated by shaking 0.10 g of material in dH2O or in a

165

saline ¼-strength Ringer’s solution with an E. coli concentration of 106 CFU/mL for 4 hours at

166

ambient temperature and estimating the remaining bacteria in suspension by cultivation thereafter.

167

The number of bacteria removed from the suspension was calculated by subtracting the cultivation

168

results from the initial bacterial concentration. The bacteria suspensions were cultivated in duplicate

169

on Petrifilm (3M, Sweden), and the CFU were calculated using the ImageJ image-analysis tool.27

170

Dependence of material-water ratio

171

The dependence of the material-water ratio was evaluated using the same method as the bacterial

172

reduction test, but the volume of the bacterial suspension was varied while the bacterial

173

concentration was kept constant at 106 CFU/mL or 105 CFU/mL. The amount of TEMPO-oxidized

174

cellulose fibers were kept constant at 0.10 g and 10 mL, 25 mL, 50 mL and 100 mL of bacterial

175

suspension were used for the bacterial reduction test.

176

Dependence of bacterial concentration

177

Different initial bacterial concentrations were tested while the volume was kept constant at 10 mL,

178

and the amount of fibers was kept constant at 0.10 g. The procedure was similar to the bacterial

ACS Paragon Plus Environment

6

Page 7 of 22

Environmental Science & Technology

179

reduction test except that the initial bacterial concentrations tested were 104, 105, 106 and 107

180

CFU/mL.

181

Dependence of time

182

As described in the bacterial reduction test, 0.10 g of material was added to 10 mL of dH2O with a

183

bacterial concentration of approximately 106 CFU/mL. The bacteria were incubated with the material

184

on a shaking table at room temperature, and samples were collected in 1-hour increments over a 4-

185

hour period and cultivated on Petrifilm.

186 187

Water samples from nature

188

A total of three different water samples were collected in nature: a water sample from the Mississippi

189

River (New Orleans, LA, USA); a water sample from Nybroviken (Stockholm, Sweden); and a turbid

190

water sample from a ditch (Vallentuna, Sweden). The initial bacterial concentration in the samples

191

was determined through cultivation. The bacterial reduction capacities of the modified materials

192

were tested with the three natural water samples using the bacterial reduction test. The turbid ditch

193

water sample, which contained a significant amount of clay, was filtered through a qualitative

194

Munktell filter paper, grade 3 (Ahlstrom Falun AB, Falun, Sweden) to remove coarse particles before

195

it was used in the bacterial reduction test.

196 197

Water filters were created by adding 0.7 g of cellulose fiber, unmodified and LbL modified, to 12 mL

198

plastic syringes with a diameter of 15 mm. A water sample from Nybroviken (Stockholm, Sweden)

199

was used for the filtration test where 10 mL of the natural water sample was filtered through the

200

cellulose fiber filter and the filtrate was cultivated on Petrifilm to determine the efficiency of the

201

filtration. Filter paper from the Safe Water Book was used as a commercial reference for the

202

filtration test. All tests were performed using duplicate samples.

203 204

RESULT

205

A new method for POU water purification was investigated using cellulosic pulp fibers and filter

206

paper modified with PVAm/PAA/PVAm multilayers to obtain bacteria adsorbing properties. This

207

modification method yields a non-leaching, contact-active material that had previously been found

208

to attract large amounts of bacteria when applied to cellulosic pulp fibers.17 TEMPO oxidized pulp

ACS Paragon Plus Environment

7

Environmental Science & Technology

209

fibers were included in the study, as this pretreatment has previously been shown to give an

210

increased bacteria adsorbing effect.10 To evaluate the suitability of these materials for a POU water

211

treatment, characterization for polymer content (nitrogen analysis) and bacterial assays were

212

conducted, using E. coli as a model bacteria as well as natural water samples.

Page 8 of 22

213 214

Fiber size measurement

215

The size of the cellulose pulp fibers was determined to get an approximation of the surface area on

216

fibers. The average fiber length was 2.209 mm and the average fiber width was 32.1 μm, both

217

weighted towards the fiber area. The average surface area of one fiber is then approximately 0.14

218

mm2.

219 220

The length of E. coli varies between 1.6 to 3.1 μm and the average width is between 0.7 to 1.1 μm, but

221

the bacteria size varies depending on bacteria strain and cultivation conditions.28 If the surface area

222

occupied by one E. coli on the cellulose fiber is roughly estimated to 3 μm2, then approximately 46

223

000 bacteria could theoretically fit in an optimized monolayer on an average cellulosic pulp fiber.

224 225

The number of fibers per gram of pulp is usually somewhere between 2.3 to 5.2 million fibers per g

226

for softwood pulp, as the one used in this study.29 If 46 000 bacteria could fit on one fiber, then 1 g of

227

pulp fibers could adsorb approximately 1011 E. coli. That imply that 1 g of modified pulp could

228

theoretically remove all bacteria from 100 L of water, if the bacterial concentration of the water was

229

106 CFU/mL. These are theoretical estimations, based on optimal bacteria attachment, but it could

230

be interesting when estimating the potential of using freely dispersed fibers in a POU water

231

purification process.

232 233

Nitrogen analysis

234

Nitrogen analysis was performed to estimate the amount of adsorbed cationic PVAm on the

235

modified materials, as PVAm is the only nitrogen-containing compound added in the LbL process.

236

The modified TEMPO oxidized cellulose fibers were expected to have a higher nitrogen content than

237

the modified cellulose fibers because the TEMPO oxidation increases the net negative charge of the

238

fiber and thereby increases the possibility to adsorb cationic PVAm.10, 25 Taking large variations into

ACS Paragon Plus Environment

8

Page 9 of 22

Environmental Science & Technology

239

account, no significant difference in the nitrogen content was observed for the three different

240

modified materials, i.e., the amount of adsorbed PVAm was approximately the same for all materials

241

(Figure 1). However, the nitrogen content in the TEMPO cellulose fibers was much lower than the

242

results presented in the study by Illergård et al., which indicated the potential to adsorb more

243

cationic PVAm onto the oxidized fibers and enhance the bacteria adsorbing effect.10 The unmodified

244

reference cellulose fibers and unmodified TEMPO oxidized cellulose fibers did not contain any

245

nitrogen, while the unmodified reference filter paper did contain a small amount of nitrogen, which

246

is probably because it is treated to increase the wet strength of the filter.10 The results of the nitrogen

247

content in the modified materials have large variations, as shown by the error bars in Figure 1. This

248

behavior has been observed in previous studies for multilayer modification with PVAm and could be

249

caused by an uneven distribution of PVAm on the cellulose fibers.10

250 251 252 253

Figure 1. Result from the nitrogen analysis for modified and reference material. The error bars represent a 95 % confidence interval.

254 255

Scanning electron microscopy

256

The macrostructure of the cellulose fibers and the filter paper can be seen in the SEM micrographs

257

at x150 magnification (Figure 2). It can be seen that the fibers in the filter paper are tightly packed

258

together, resulting in less surface area available for bacteria adsorption compared to the free

259

cellulose fibers. It is debated how the morphology of a surface affects bacterial adhesion, some

260

researcher claim that bacteria adhesion is promoted with an increased roughness of the surface as it

261

will increase the specific surface area available for attachment, other studies have shown that a

262

change in the surface roughness do not affect the bacteria adsorption.30 The morphology of the

ACS Paragon Plus Environment

9

Environmental Science & Technology

Page 10 of 22

263

adsorbed polyelectrolyte multilayer is however difficult to visualize since the thickness of the

264

polyelectrolyte multilayer is in the nanometer range and the cellulose fibers have an average width

265

of 32.1 μm.31 A previous study by Lingström et al. has shown that adsorbed multilayers of

266

polyelectrolytes on cellulose fibers can be visualized in environmental SEM as a smoothening of the

267

surface.32 They used 11 polyelectrolyte layers and concluded that the roughness of the fiber surface

268

decreased when the polyelectrolytes were adsorbed. A similar smoothening effect of the fiber surface

269

could possibly be detected in the high magnification SEM micrographs of the cellulose fiber. No

270

difference on the fiber surface could be seen on fibers in the filter paper, before and after the

271

polyelectrolyte adsorption.

272

273 274 275 276 277 278 279 280

Figure 2. SEM micrographs showing the macrostructure and fiber surface of the cellulosic materials. a) Unmodified cellulose fibers at x150 magnification, b) surface on unmodified cellulose fiber at x5000 magnification, c) surface on 3L modified cellulose fiber at x5000 magnification, d) unmodified filter paper at x150 magnification, e) surface on fiber in unmodified filter paper at x5000 magnification and f) surface on fiber in 3L modified filter paper at x5000 magnification.

281

The bacterial removal capacities of the modified materials were tested in dH2O and ¼-Ringer’s

282

solution. Filter paper from Safe Water Book, containing silver was used as a commercial reference.

283

The initial bacterial concentration in this study was set to 106 CFU/mL, and all materials were

284

compared with non-modified material, which showed no bacterial reduction. The bacterial

285

reduction test showed that more than 99.9 % of the initial bacteria are removed after 4 hours of

286

incubation with the polyelectrolyte modified materials (Figure 3). The highest bacterial removal

Bacterial reduction

ACS Paragon Plus Environment

10

Page 11 of 22

Environmental Science & Technology

287

capacity, which was 99.98 % of the initial bacteria after 4 hours, was noted for the cellulose fibers in

288

dH2O and TEMPO cellulose in ¼-Ringer’s solution. The commercial reference reduced the viable

289

bacteria with 100 % in dH2O and 99.996 % in ¼-Ringer’s solution.

290

291 292 293 294 295 296

Figure 3. The percentage of removed bacteria from suspension after 4 hours of incubation with modified materials, in dH2O and ¼-Ringer’s solution. SWB is the commercial reference Safe Water Book, 3 L Cellulose is the modified cellulosic fiber, 3 L TEMPO is the modified TEMPO-oxidized cellulosic fiber and 3 L Filter is the modified filter paper. The initial bacterial concentration was 106 CFU/mL and the error bars represent the standard deviation.

297 298

Previous investigations of the bacteria adsorbing effect of multilayer-treated fibers have mainly been

299

conducted using ¼-strength Ringer’s solution to provide a more beneficial environment for the

300

bacteria.17, 33 The ¼-strength Ringer’s solution used in this study had a pH of 6.45 and the dH2O had

301

a pH of 5.10. It is still unclear how the ion strength affects the bacterial adhesion.34 Some studies

302

report that increasing the ionic strength will increase the bacterial adhesion, while others report the

303

opposite.35-37 The bacterial reduction test shows a difference in the bacterial reduction for the

304

cellulose fibers when using ¼-Ringer’s solution compared to using dH2O, but no notable difference

305

was observed for the TEMPO cellulose and for the filter paper (Figure 3). Illergård et al. reported

306

that no difference in bacterial removal was observed when analyzing the bacterial removal efficiency

307

of the multilayer modified cellulosic fibers in different salt concentrations.24 The ions in water will

308

interact with the charged polyelectrolytes, but bacterial adhesion to surfaces is complex and is

309

affected by many different parameters, e.g., salt concentration, pH, type of bacteria, etc.

310

ACS Paragon Plus Environment

11

Environmental Science & Technology

Page 12 of 22

311

Time dependence

312

The time it takes to remove the bacteria is an important parameter when treating drinking water.

313

The number of remaining bacteria in suspension after 1, 2, 3, and 4 hours of contact-time were

314

therefore evaluated. The test shows that all modified materials greatly decreased the bacterial

315

concentration after only one hour of contact-time (Figure 4). The TEMPO cellulose removed

316

99.89 % of the bacteria from the suspension within the first hour while the cellulose fibers and the

317

filter paper removed 99.65 % and 98.03 % of the bacteria during the first hour, respectively. The

318

filter paper needed more time to remove the same number of bacteria as the cellulose fibers and the

319

TEMPO cellulose. The reason for this is most likely attributed to the cellulose and TEMPO cellulose

320

fibers being freely dispersed in the water compared to the fixed fibers in the filter paper. This

321

difference will increase the probability for the material to attract and bind to the bacteria. The

322

results from the time dependence test are promising, as many techniques used to purify water

323

require several hours to obtain safe drinking water. 5

324 325 326 327

Figure 4. The results from the time dependence test showing the percentage of bacteria remaining in suspension in hourly increments after incubation with modified materials. The initial bacterial concentration was 106 CFU/mL. The error bars represent the standard deviation.

328 329

Concentration dependence

330

The concentration dependence test shows that the number of bacteria remaining in the suspension

331

depends on the initial bacterial concentration (Figure 5). The number of remaining bacteria in the

332

water increases significantly when the initial bacterial concentration increases from 106 CFU/mL to

ACS Paragon Plus Environment

12

Page 13 of 22

Environmental Science & Technology

333

107 CFU/mL, but the percentage of bacteria removed from the suspension also increases when the

334

initial bacterial concentration increases. This is an effect of a large increase initial bacterial load

335

compared to the increase of remaining bacteria. The amount of remaining bacteria is approximately

336

6 times larger for the initial concentration of 107 CFU/mL compare to the concentration of

337

105 CFU/mL. The increase in initial bacterial load is however 100 times larger when increasing the

338

bacterial concentration from 107 CFU/mL to 105 CFU/mL, resulting in higher bacterial removal

339

efficiency for 107 CFU/mL. A similar effect of increase in removal efficiency has been seen in a

340

previous study when the bacterial load was increased for contact active materials, where it has been

341

suggested that the amount of bacteria remaining in suspension at lower concentrations could be an

342

equilibrium effect.24 This might be avoided if using the materials in cross flow filtration mode. The

343

increase in remaining bacteria in suspension when the initial concentration increase to 107 CFU/mL

344

could be a result of increased saturation of the bacteria adsorbing surface of the fibers.

345 346 347 348 349 350

Figure 5. Result from the concentration test showing the number of remaining bacteria in suspension and the percentage of removed bacteria after 4 hours of incubation with 0.1 g modified TEMPO cellulose. The initial bacterial load ranges from 104-107 CFU/mL. The error bars represent the standard deviation.

351

Material-water ratio dependence

352

The material-water ratio dependence test shows that the bacterial reduction efficiency increases

353

when the material-water ratio increases (Figure 6). However, the results show that it is possible to

354

use 1/5 of the amount of modified materials compared to previous tests, i.e., 0.2 w/w % material-

355

water ratio, and still obtain a bacterial reduction greater than 99.9 %. The difference in bacterial

356

reduction for the different ratios is small compared to the initial bacterial concentration.

ACS Paragon Plus Environment

13

Environmental Science & Technology

Page 14 of 22

357

Specifically, only 0.16 percentage points of bacterial reduction efficiency differs between the smallest

358

and largest water volume tested. These results indicate that it may be possible to use less material

359

and scale-up the water treatment method.

360 361 362

363 364 365 366 367

Figure 6. Result of the material-water ratio dependence, showing the percentage of removed bacteria vs. the material-water ratio after 4 hours of incubation with modified TEMPO cellulose. Ci is the initial bacterial concentration, the light grey bars are Ci =105 CFU/mL and the dark gray bars are Ci =106 CFU/mL. The error bars represent the standard deviation.

368 369

Water samples from nature

370

To get a more realistic lab set-up, the modified materials bacterial removal capacities were tested

371

with three different water samples from nature. It is known that chlorine is less efficient for

372

sterilization of turbid water with a significant amount of particles; thus, it is important to test water

373

treatment techniques with water samples containing different turbidities.38 The water sample from

374

the ditch water contained approximately 8 x 103 CFU/mL, the Mississippi River contained

375

approximately 1.5 x 105 CFU/mL, and the water sample from Nybroviken contained approximately

376

2 x 104 CFU/mL and (Table 1). Natural water samples can contain a large number of different

377

microorganisms and the colony growth on the cultivation on Petrifilm indicates that the water

378

samples contained different colony forming bacteria.

379

ACS Paragon Plus Environment

14

Page 15 of 22

Environmental Science & Technology

380

When tested in the bacterial reduction assay, the bacterial concentration of the Mississippi River

381

water sample was reduced by 97 % with the cellulose fibers, 95 % with the TEMPO cellulose and

382

94 % with the filter paper (Table 1). The bacterial content in the sample from Nybroviken was

383

reduced by 93 % with modified the cellulose fibers and 91 % with the TEMPO cellulose, while the

384

bacterial reduction was only 68 % of the initial concentration for the water sample treated with filter

385

paper after 4 hours of incubation. No significant reduction in bacterial concentration was observed

386

for the ditch water sample treated with the modified materials, the bacterial reduction was below

387

60 % of the initial concentration.

388 389 390 391

Table 1. Result from the bacterial reduction test with natural water samples, shown as bacterial removal efficiency after 4 hours of incubation with the modified materials. Water sample

Initial bacterial conc. [CFU/mL]

Cellulose fibers

TEMPO cellulose

Filter paper

Ditch water

8 x 103

< 60 %

< 60 %

< 60 %

97 %

95 %

94 %

93 %

91 %

68 %

Mississippi River

1.5 x 10

5

water Nybroviken water

2 x 104

392 393

Water from Nybroviken was collected at a later occasion to be used for the filtration test. This time

394

the water sample had a bacterial concentration of approximately 130 CFU/mL, which was possible to

395

detect through cultivation. The cellulose fiber filter, containing 0.7 g fiber, had a thickness of 20 mm

396

and a density of approximately 0.20 g/cm3. The three layer modified filter removed greater than 99

397

% of the bacteria compared to the unmodified filter that removed 43 % of bacteria from the water

398

sample (Figure 7). The commercial reference removed greater than 99 % of the bacteria in the

399

natural water sample.

ACS Paragon Plus Environment

15

Environmental Science & Technology

Page 16 of 22

400 401 402 403 404

Figure 7. Result from the filtration test using natural water from Nybroviken. The water filter contained 0.7 g of cellulose fibers, unmodified or modified with the LbL technique. SWB is the commercial reference Safe Water Book. The error bars represent the standard deviation.

405

DISCUSSION

406

The bacteria adsorbing cellulosic materials have capacity to remove more than 99.9 % of bacteria in

407

water with an initial bacterial concentration of 106 CFU/mL. The main reduction of bacteria is

408

performed within one hour, and a 0.2 w/w % material-water ratio can be used to purify water as long

409

as contact between the bacteria adsorbing material and the bacteria is maintained. These results

410

present the initial stages of developing an environmentally friendly and low cost disposable POU

411

treatment. The modified materials used in this study do not release any biocides to water, which is a

412

significant advantage compared to other sterilization methods.7, 8, 10

413 414

Modified TEMPO cellulose was the most efficient material for removing bacteria from water,

415

followed by modified cellulose fibers and then the modified filter paper. The cellulose fibers were

416

slightly better at removing bacteria from water than the filter paper, which is potentially attributed

417

to the cellulose fibers being freely dispersed in the water compared to the fixed fibers of the filter

418

paper. This gives the cellulose fibers a larger active adsorption area and makes it easier for the fiber

419

to attract and bond with the bacteria. The material-water ratio dependence test indicates that it is

420

very important to have good circulation of the fibers to attain an efficient bacterial removal when

421

using larger volumes of water. Contact-active materials need to maintain contact with the bacteria in

422

order to affect the bacteria, e.g. to adsorb them to a contact-active surface. It is more difficult for the

423

fibers to attract and bond with the bacteria when the average distance between the fibers and the

ACS Paragon Plus Environment

16

Page 17 of 22

Environmental Science & Technology

424

bacteria increases, e.g., when the fiber concentration decreases with larger volumes of water, which

425

is an issue that could possibly be resolved by filtering water through the modified material. The

426

advantage of having the fibers freely dispersed in the water is that it allows bacteria to adsorb an all

427

parts of the fibers. The cellulose fibers have a very large specific surface area that could adsorb large

428

amount of bacteria, giving an excellent bacterial removal capacity per gram of fibers, if the bacteria

429

adsorption was optimized. The fibers need however to be removed from the water after the

430

purification process, and this implies that a filtration step will probably be required. One way to

431

avoid this two-step process is to create filters from the bacteria adsorbing cellulosic fibers. This will

432

decrease the surface area available for bacterial adsorption but it will make the fibers easier to

433

handle and use for water purification. Filtering will also improve the performance of the bacteria

434

adsorbing materials for natural water.

435 436

The water samples from nature showed that the modified materials are less efficient at removing

437

microorganisms from real-life water samples, when using the materials dispersed in the water,

438

compared to removing bacteria from bacterial suspensions prepared in the lab. The modified

439

cellulose fibers removed 97 % of the bacteria in the Mississippi river water sample and 93 % of the

440

bacteria in the Nybroviken water sample, while no reduction was observed for the turbid ditch water

441

sample. One explanation for the reduced bacterial removal efficiency compared to previous test

442

could be that the natural water samples contain particles that shield the bacteria.38 The particle

443

surface provides a good foundation for biofilms that can host and protect microorganisms and

444

thereby prevent the modified fibers from attracting and bonding with the bacteria.39 This has been

445

shown to be an issue for other sterilization methods as well, e.g., chlorination and UV-light

446

treatment.38, 39 Another possible explanation could be the complex mixture of microorganisms in

447

natural water samples, the antibacterial effect of the LbL modification has previously been

448

successfully tested with the gram-positive bacteria Bacillus subtilis, but research on other types of

449

bacteria and microorganisms present in water, e.g. protozoa, would be valuable for understanding

450

the issue.24

451 452

The presence of particles renders the notion of having modified fibers freely dispersed in water

453

insufficient, and it will most likely be desired to remove the particles before exposing the

ACS Paragon Plus Environment

17

Environmental Science & Technology

Page 18 of 22

454

contaminated water to the bacteria adsorbing materials during the decontamination process. Using

455

multilayer modified cellulosic materials in filtration mode will both remove larger particles and

456

promote for an increased contact between the bacteria adsorbing material and bacteria in the water,

457

which is critical for an efficient bacterial removal when using a contact-active method. The filtration

458

test using natural water showed that it is possible to improve the bacterial removal efficiency for

459

natural water samples by filtering it through the modified fibers. The water filter containing

460

modified cellulose fibers had a bacterial removal efficiency greater than 99 %, similar to the

461

commercial reference. It can be compared to the filter with unmodified fibers, which removed 43 %

462

of the bacteria from the natural water sample. This indicates that it should be possible to develop an

463

efficient water treatment method if the modified materials are used in filtration mode to remove

464

both bacteria and particles that impair bacteria removal. Removing particles from water would also

465

decrease the turbidity and make the water more pleasant to drink, which is an important parameter

466

when promoting the use of POU water treatments in developing countries, especially for children. It

467

should be noted that the bacterial concentration, possible to detect through cultivation, was

468

considerably lower for the water sample collected for the filtration test compared the high bacterial

469

concentration determined for the water sample collected for the reduction test, with the material

470

dispersed in the water, even though the water samples were collected at the same spot but at two

471

different occasions.

472 473

There is little data in literature about bacteria adsorbing POU methods, most research has been

474

focused on leaching materials that require a slightly different experimental setup. The commercial

475

reference used in this study inactivated all bacteria in dH2O and had a very high bacterial reduction

476

in ¼-strength Ringer’s solution. This was expected since the reference filter contains silver, which is

477

known to be an efficient bactericide and the 4 hour incubation will allow plenty of time for bacterial

478

inactivation, provided that the concentration of silver is high enough.15 Dankovich et al. reported a

479

bacterial log reduction value of 6 for cellulosic filters impregnated with silver particles, similar to the

480

commercial reference, which could be compared to a log reduction value of 3-4 for the bacteria

481

adsorbing cellulosic fibers modified with multilayers.8 However, the study evaluating the silver

482

infused filter paper used a higher initial bacterial concentration, 108 CFU/mL, but the number of

483

remaining bacteria in the effluent water was in the same range as for the contact-active cellulosic

ACS Paragon Plus Environment

18

Page 19 of 22

Environmental Science & Technology

484

fibers.8 Zeng et al. reports that they obtained a bacterial reduction over 97 % when filtering water

485

containing E. coli with a concentration of 105 CFU/mL through bactericidal hydrogel filters made

486

from reduced graphene oxide and silver, which is far less efficient than the bacteria adsorbing

487

cellulosic fibers outlined in this study.16

488 489

Cellulose is a natural biomaterial that is relatively cheap and safe to handle, and combined with the

490

non-leaching bacteria adsorbing modification, it presents an environmentally friendly option for

491

current POU treatment techniques based on releasing toxic compounds. Cellulosic fibers are great

492

for making paper sheets and are currently used in a variety of filters ranging from simple coffee

493

filters to advanced fuel and air filters in cars. The functionalized cellulosic fibers can be processed

494

into paper sheets, which could be used for water filtration. The water filter would then rely on

495

physical removal of bacteria through electrostatic interactions and should be able to allow a higher

496

flux compared to filters relying on size exclusion of bacteria. However, the pore size of the filters

497

must still be small enough to obtain sufficient contact between the functionalized fibers and all

498

bacteria in the water, as it is critical for an efficient contact-active POU technique.

499 500

There are potentially more advantages using a contact-active material for water purification than

501

only the removal of bacteria, as most impurities found in natural water are negatively charged.

502

Cationic polyelectrolytes are often used in water treatment as they have been proven to be the most

503

effective flocculent agent.40 The cationic PVAm on the modified cellulosic fibers could possibly

504

remove other impurities from water in addition to removing bacteria. Mayer-Gall et al. successfully

505

used polyester textile functionalized with PVAm to remove toxic chromate ions from contaminated

506

groundwater. The ability to purify water from other harmful compounds could potentially be a great

507

advantage for the contact-active bacteria adsorbing cellulosic fibers compared to other water

508

treatment techniques based on leaching biocides. The bacterial reduction capacity of the

509

functionalized cellulosic fibers is good and the material could with an optimized product design,

510

preferably cross flow filtration, be a promising alternative for a disposable POU water purification

511

device.

512 513

AUTHOR INFORMATION

ACS Paragon Plus Environment

19

Environmental Science & Technology

514

Corresponding Author

515

* Tel: +46 8 790 8104, [email protected], Teknikringen 56-58, SE-100 44, Stockholm, Sweden

516

ORCID ORCID

517 518 519 520

Anna Ottenhall: Josefin Illergård: Monica Ek:

521

ABBREVIATIONS

522

CFU

Colony forming units

523

Ci

Initial bacterial concentration

524

dH2O

Deionized water

525

LbL

Layer-by-Layer

526

PAA

Polyacrylic acid

527

POU

Point-of-use

528

PVAm

Polyvinylamine

529

SEM

Scanning electron microscope

530

TEMPO

2,2,6,6-Tetramethyl-1-piperidinyloxy

Page 20 of 22

0000-0002-1656-1465 0000-0003-1812-7336 0000-0003-3858-8324

531 532 533 534 535

1. Bain, R.; Cronk, R.; Hossain, R.; Bonjour, S.; Onda, K.; Wright, J.; Yang, H.; Slaymaker, T.; Hunter, P.; Prüss-Ustün, A.; Bartram, J., Global assessment of exposure to faecal contamination through drinking water based on a systematic review. Trop. Med. Int. Health 2014, 19, (8), 917-927.

536 537

2. Cabral, J. P., Water microbiology. Bacterial pathogens and water. Int. J. Environ. Res. Pub. Health 2010, 7, (10), 3657-3703.

538 539

3. Doocy, S.; Burnham, G., Point‐of‐use water treatment and diarrhoea reduction in the emergency context: an effectiveness trial in Liberia. Trop. Med. Int. Health 2006, 11, (10), 1542-1552.

540 541

4. Oyanedel-Craver, V. A.; Smith, J. A., Sustainable colloidal-silver-impregnated ceramic filter for point-of-use water treatment. Environ. Sci. Technol. 2007, 42, (3), 927-933.

542 543 544

5. Sobsey, M. D.; Stauber, C. E.; Casanova, L. M.; Brown, J. M.; Elliott, M. A., Point of Use household drinking water filtration: A practical, effective solution for providing sustained access to safe drinking water in the developing world. Environ. Sci. Technol. 2008, 42, (12), 4261-4267.

545 546

6. Ehdaie, B.; Krause, C.; Smith, J. A., Porous ceramic tablet embedded with silver nanopatches for low-cost point-of-use water purification. Environ. Sci. Technol. 2014, 48, (23), 13901-13908.

547 548

7. Gopal, K.; Tripathy, S. S.; Bersillon, J. L.; Dubey, S. P., Chlorination byproducts, their toxicodynamics and removal from drinking water. J. Hazard. Mater. 2007, 140, (1–2), 1-6.

REFERENCES

ACS Paragon Plus Environment

20

Page 21 of 22

Environmental Science & Technology

549 550

8. Dankovich, T. A.; Gray, D. G., Bactericidal Paper Impregnated with Silver Nanoparticles for Point-of-Use Water Treatment. Environ. Sci. Technol. 2011, 45, (5), 1992-1998.

551

9.

552 553

10. Illergård, J. The creation of antibacterial fibres through physical adsorption of polyelectrolytes. Ph.D. Dissertation, KTH Royal Institute of Technology, Stockholm, Sweden, 2012.

554 555

11. Dann, A. B.; Hontela, A., Triclosan: environmental exposure, toxicity and mechanisms of action. J. Appl. Toxicol. 2011, 31, (4), 285-311.

556 557

12. Fabrega, J.; Luoma, S. N.; Tyler, C. R.; Galloway, T. S.; Lead, J. R., Silver nanoparticles: behaviour and effects in the aquatic environment. Environ. Int. 2011, 37, (2), 517-531.

558 559 560

13. Sütterlin, S.; Tano, E.; Bergsten, A.; Tallberg, A.-B.; Melhus, Å., Effects of silver-based wound dressings on the bacterial flora in chronic leg ulcers and its susceptibility in vitro to silver. Acta Derm. Venereol. 2012, 92, (1), 34-39.

561 562

14. Levy, S. B., Factors impacting on the problem of antibiotic resistance. J. Antimicrob. Chemother. 2002, 49, (1), 25-30.

563 564

15. Mijnendonckx, K.; Leys, N.; Mahillon, J.; Silver, S.; Van Houdt, R., Antimicrobial silver: uses, toxicity and potential for resistance. BioMetals 2013, 26, (4), 609-621.

565 566 567

16. Zeng, X.; McCarthy, D. T.; Deletic, A.; Zhang, X., Silver/reduced graphene oxide hydrogel as novel bactericidal filter for Point‐of‐Use water disinfection. Adv. Funct. Mater. 2015, 25, (27), 43444351.

568 569

17. Illergård, J.; Römling, U.; Wågberg, L.; Ek, M., Biointeractive antibacterial fibres using polyelectrolyte multilayer modification. Cellulose 2012, 19, (5), 1731-1741.

570 571 572

18. Poverenov, E.; Shemesh, M.; Gulino, A.; Cristaldi, D. A.; Zakin, V.; Yefremov, T.; Granit, R., Durable contact active antimicrobial materials formed by a one-step covalent modification of polyvinyl alcohol, cellulose and glass surfaces. Colloids Surf. B Biointerfaces 2013, 112, 356-361.

573 574 575

19. El-Khouly, A. S.; Kenawy, E.; Safaan, A. A.; Takahashi, Y.; Hafiz, Y. A.; Sonomoto, K.; Zendo, T., Synthesis, characterization and antimicrobial activity of modified cellulose-graft-polyacrylonitrile with some aromatic aldehyde derivatives. Carbohyd. Polym. 2011, 83, (2), 346-353.

576 577

20. Tripathi, B. P.; Dubey, N. C.; Stamm, M., Functional polyelectrolyte multilayer membranes for water purification applications. J. Hazard. Mater. 2013, 252–253, 401-412.

578 579 580

21. Westman, E.-H.; Ek, M.; Enarsson, L.-E.; Wågberg, L., Assessment of antibacterial properties of polyvinylamine (PVAm) with different charge densities and hydrophobic modifications. Biomacromolecules 2009, 10, (6), 1478-1483.

581 582

22. Decher, G., Fuzzy nanoassemblies: toward layered polymeric multicomposites. Science 1997, 277, (5330), 1232-1237.

583 584

23. Hong, Y.; Brown, D. G., Electrostatic behavior of the charge-regulated bacterial cell surface. Langmuir 2008, 24, (9), 5003-5009.

585 586 587

24. Illergård, J.; Wågberg, L.; Ek, M., Contact-active antibacterial multilayers on fibres: a step towards understanding the antibacterial mechanism by increasing the fibre charge. Cellulose 2015, 22, (3), 2023-2034.

588 589 590

25. Saito, T.; Hirota, M.; Tamura, N.; Kimura, S.; Fukuzumi, H.; Heux, L.; Isogai, A., Individualization of nano-sized plant cellulose fibrils by direct surface carboxylation using TEMPO catalyst under neutral conditions. Biomacromolecules 2009, 10, (7), 1992-1996.

591 592

26. Lichter, J. A.; Rubner, M. F., Polyelectrolyte multilayers with intrinsic antimicrobial functionality: the importance of mobile polycations. Langmuir 2009, 25, (13), 7686-7694.

Folia Water website, http://www.foliawater.com/safe-water-book-1 (9 February 2017)

ACS Paragon Plus Environment

21

Environmental Science & Technology

Page 22 of 22

593 594

27. Schneider, C. A.; Rasband, W. S.; Eliceiri, K. W., NIH Image to ImageJ: 25 years of image analysis. Nat Meth 2012, 9, (7), 671-675.

595 596 597

28. Volkmer, B.; Heinemann, M., Condition-Dependent Cell Volume and Concentration of Escherichia coli to Facilitate Data Conversion for Systems Biology Modeling. PLOS ONE 2011, 6, (7), e23126.

598

29.

599 600

30. An, Y. H.; Friedman, R. J., Concise review of mechanisms of bacterial adhesion to biomaterial surfaces. J. biomed. mater. res. 1998, 43, (3), 338-348.

601 602 603

31. Illergård, J.; Enarsson, L.-E.; Wågberg, L.; Ek, M., Interactions of Hydrophobically Modified Polyvinylamines: Adsorption Behavior at Charged Surfaces and the Formation of Polyelectrolyte Multilayers with Polyacrylic Acid. ACS Appl. Mater. Interfaces 2010, 2, (2), 425-433.

604 605

32. Lingström, R.; Wågberg, L.; Larsson, P. T., Formation of polyelectrolyte multilayers on fibres: Influence on wettability and fibre/fibre interaction. J. Colloid Interface Sci. 2006, 296, (2), 396-408.

606 607

33. Henschen, J.; Illergård, J.; Larsson, P. A.; Ek, M.; Wågberg, L., Contact-active antibacterial aerogels from cellulose nanofibrils. Colloids Surf. B Biointerfaces 2016, 146, 415-422.

608 609

34. Poortinga, A. T.; Bos, R.; Norde, W.; Busscher, H. J., Electric double layer interactions in bacterial adhesion to surfaces. Surf. Sci. Rep. 2002, 47, (1), 1-32.

610 611

35. Zita, A.; Hermansson, M., Effects of ionic strength on bacterial adhesion and stability of flocs in a wastewater activated sludge system. Appl. Environ. Microbiol. 1994, 60, (9), 3041-3048.

612 613

36. Sheng, X.; Ting, Y. P.; Pehkonen, S. O., The influence of ionic strength, nutrients and pH on bacterial adhesion to metals. J. Colloid Interface Sci. 2008, 321, (2), 256-264.

614 615 616

37. Yee, N.; Fein, J. B.; Daughney, C. J., Experimental study of the pH, ionic strength, and reversibility behavior of bacteria–mineral adsorption. Geochim. et Cosmochim. Acta 2000, 64, (4), 609-617.

617 618

38. Lechevallier, M. W.; Cawthon, C. D.; Lee, R. G., Factors promoting survival of bacteria in chlorinated water supplies. Appl. Environ. Microbiol. 1988, 54, (3), 649-654.

619 620

39. Schillinger, J. E.; Gannon, J. J., Bacterial adsorption and suspended particles in urban stormwater. J. Water Pollut. Control Fed. 1985, 384-389.

621 622 623 624

40. Bolto, B.; Gregory, J., Organic polyelectrolytes in water treatment. Water Res. 2007, 41, (11), 2301-2324.

Nanko, H.; Button, A.; Swann, C. E., The world of market pulp. WOMP LLC: 2005.

ACS Paragon Plus Environment

22