Co Embedded in

Subscriber access provided by Thompson Rivers University | Library

Article

Metal-Organic Framework derived Co3ZnC/Co embedded in nitrogen doped CNT-grafted carbon polyhedra as high-performance electrocatalyst for water splitting Zhou Yu, Yu Bai, Shimin Zhang, Yuxuan Liu, Naiqing Zhang, Guohua Wang, Junhua Wei, Qibing Wu, and Kening Sun ACS Appl. Mater. Interfaces, Just Accepted Manuscript • DOI: 10.1021/acsami.7b16130 • Publication Date (Web): 29 Jan 2018 Downloaded from http://pubs.acs.org on January 29, 2018

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

ACS Applied Materials & Interfaces is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 29 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

Metal-Organic Framework derived Co3ZnC/Co embedded in nitrogen doped CNT-grafted carbon polyhedra as high-performance electrocatalyst for water splitting Zhou Yu,†, ‡ Yu Bai, *,

‡, #

Shimin Zhang, † Yuxuan Liu, † Naiqing Zhang,

‡

Guohua

Wang, § Junhua Wei, § Qibing Wu § and Kening Sun, *, ‡ †

School of Chemistry and Chemical Engineering, Harbin Institute of Technology,

Harbin, 150001, P. R. China ‡

Academy of Fundamental and Interdisciplinary Sciences, Harbin Institute of

Technology, Harbin, 150001, P. R. China #

Advanced Research Institute for Multidisciplinary Science, Beijing Institute of

Technology, Beijing, 100081, P. R. China §

State Key Laboratory of Advanced Chemical Power Sources, Zunyi, 563000, P. R.

China

Abstract: The development of efficient, low-cost, and stable electrocatalysts for overall water splitting is of great significance for the energy conversion. Transition metal carbides (TMCs) with high catalytic activity and low cost have attracted great interests. Nevertheless, utilizing an efficient catalyst for overall water-splitting is still a challenging issue for TMCs. Herein, we report the synthesis of a high-performance electrocatalyst comprising Co3ZnC and Co nanoparticles embedded in nitrogen doped carbon nanotube (CNT)-grafted carbon polyhedral (Co3ZnC/Co-NCCP) by the pyrolysis of bimetallic zeolitic imidazolate frameworks in a reductive atmosphere of Ar/H2. The Co3ZnC/Co-NCCP exhibits remarkable electrochemical activity in catalyzing both the OER and HER, in terms of low overpotential and excellent 1

ACS Paragon Plus Environment

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

stability. Furthermore, the Co3ZnC/Co-NCCP catalyst leads to a highly performed overall water splitting in 1M KOH electrolyte, delivering a current density of 10 mA cm-2 at a low applied external potential of 1.65 V and shows good stability without obvious deactivation after 10 h operation. The present strategy opens a new avenue to the design of efficient electrocatalysts in electrochemical applications. KEYWORDS: oxygen evolution reaction, transition metal carbides, carbon nanotube, bimetallic zeolitic imidazolate frameworks, alkaline media.

1. INTRODUCTION Hydrogen has been considered as a green renewable energy carrier, which can be a promising alternative for future energy strategies due to the burning of fossil fuel and environmental contamination.1, 2 Electrochemical water splitting provides an attractive and sustainable approach to obtain clean hydrogen fuel.3, 4 The water-splitting reaction involves the oxygen evolution reaction (OER) and hydrogen evolution reaction (HER), both of which require high-performance electrocatalysts to facilitate the charge transfer kinetics and improve

the energy transfer efficiency.5-8 Although

platinum-based material and precious-metal oxides (e.g. RuO2 and IrO2) have been approved to be highly efficient HER and OER catalysts, their scarcity and high cost have hindered their large-scale application.9-13 Thus, the development of efficient, earth-abundant and cost-effective catalytic materials is in urgent demand.14 Recently, transition-metal materials based catalysts, such as metal oxides,15,16 metal phosphide, 17-19

metal chalcogenides,20, 21 and metal carbides/nitride,22, 23 have been investigated

extensively as OER and HER electrocatalysts. Among these materials, transition metal 2


Page 2 of 29

Page 3 of 29 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


carbides (TMCs) have attracted wide interest in the electrochemical applications due to their high electron conductivity, low-cost and chemical stability.24-26 Nevertheless, there are only a few reports focused on overall water splitting properties for TMCs-based catalysts. More importantly, TMCs generally suffer from high overpotential and low durability in the harsh electrolyte.27, 28 Notably, experimental results have shown that the combination of TMCs and heteroatom-doped (e.g. N, S and P) carbon materials represents a unique strategy to resist corrosion in alkaline solution, providing more exposed active sites and high surface area to significantly enhance the electrocatalytic performance.29-31 Lan et al.32 reported Co6Mo6C2 coated by N-doped porous carbon and anchored on N-doped reduced graphene oxide film (Co6Mo6C2/NCRGO) as excellent OER electrocatalysts. Zou et al.33 synthesized ultrasmall molybdenum carbide nanoparticles embedded within nitrogen-rich carbon, which served as an excellent HER electrocatalyst. Besides, creating heterostructures is another way to improve electrocatalytic performance owing to the synergistic effect of different materials which could promote the charge separation and enhances the exposure of active sites.34-37 For example, Wang et al.38 synthesized CoOx@CN with outstanding HER and OER performances because of the synergistic interaction between metallic Co and cobalt oxide. The catalytic performance greatly depends on the synthetic method and morphological characteristics. Therefore, it is urgent to develop an efficient method for the preparation of heterostructures TMCs and heteroatom-doped carbon composite with simple step processes and well-define architecture. 3



Recently, metal-organic frameworks (MOFs) have received great interest due to their large surface area, uniform ordered pores, easy synthesis without surfactant and tunable structure, which are promising for high-performance electrocatalytic progress. 39-43

In particular, zeolitic imidazolate frameworks (ZIFs) as a class of MOF have been

confirmed to be ideal precursors for the preparation of heteroatom-doped carbon species based nanocomposites by in situ carbonization to enhance the relevant properties. Besides, compared with bulk materials, ZIFs derived nanocomposites have a strong ability to resist drastic structural collapse caused by high temperature calcination, and the specific surface areas and pore volume can also benefit the catalytic reactions.44-46 Such as Muhler et al.47 developed a facile approach for the synthesis of Co@Co3O4 nanoparticles encapsulated in N-doped carbon nanotubes (CNTs)-grafted carbon polyhedron and exhibited their remarkable capability as bifunctional oxygen electrocatalyst. Nonetheless, to the best of our knowledge, heterostructure TMCs and heteroatom-doped carbon composite derived from ZIFs as highly efficient electrocatalysts for overall water splitting has been rarely explored so far. Herein, we report the synthesis of Co3ZnC and Co nanoparticles embedded in nitrogen doped CNT-grafted carbon polyhedral (Co3ZnC/Co-NCCP) by reductive carbonization of bimetallic Zn and Co bimetallic zeolitic imidazolate frameworks (ZnCo-ZIFs). The resulting Co3ZnC/Co-NCCP exhibits excellent activity and stability for both the OER and HER process. As expected, the Co3ZnC/Co-NCCP presents outstanding performance toward overall water splitting in alkaline condition. The 4


Page 4 of 29

Page 5 of 29 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


prominent activity would be ascribed to the unique structure and the chemical composition that provide large surface area, highly active species and robust pore structure.

2. RESULTS AND DISCUSSION The synthetic process for Co3ZnC/Co nanoparticles embedded in nitrogen doped CNT-grafted carbon polyhedra (Co3ZnC/Co-NCCP) is described in Scheme 1. The ZnCo-ZIFs were obtained via a facile room-temperature coprecipitation reaction. Then, the as-prepared ZnCo-ZIFs were pyrolyzed in a reductive atmosphere of Ar/H2 to obtain Co3ZnC/Co-NCCP. In the pyrolysis process, the cobalt and zinc ions from the ZnCo-ZIFs are converted into Co3ZnC and Co NPs and the organic ligands from the MOFs are converted into nitrogen-doped carbon nanotubes (NCNTs) grafted carbon polyhedral under the catalysis of Co nanoparticles in a reductive atmosphere.48 The interconnected CNTs within the polyhedron can significantly improve the electrical conductivity and structure stability of the resultant product. As shown in scanning electron microscopy (SEM) (Fig. S1a, b), the as-synthesized ZnCo-ZIFs exhibit a well-defined rhombic polyhedral with sizes of about 500 nm and the exterior surface is smooth. The transmission electron microscopy (TEM) image (Fig. S1c) further confirms that the ZnCo-ZIFs are solid. The measured powder X-ray diffraction (XRD) patterns of ZnCo-ZIFs show strong diffraction peaks at identical positions similar to previous report zeolite-type structure, confirming the good crystallinity and pure-phase zeolite-type structure (Fig. S1d). After carbonization under the Ar/H2 flow at 600

o

C, the ZnCo-ZIFs were transformed into 5



Co3ZnC/Co-NCCP. The corresponding XRD patterns reveal that the characteristic peaks of Co3ZnC/Co-NCCP can be well indexed to Co3ZnC (PDF 29-0524), Co (PDF 15-0806), and C (PDF 41-1487) standards. (Fig. 1a) The energy-dispersive X-ray (EDX) spectroscopy (Fig. 1b) further confirms the coexistence of Co, Zn, C, and N elements in the Co3ZnC/Co-NCCP.

(Fig. 1b)

X-ray photoelectron spectroscopy (XPS) was further employed to clarify the chemical composition of the Co3ZnC/Co-NCCP. Survey spectrum in Fig. S2 shows the existence of Zn, Co, N and C elements, which coincides with the XRD result. As shown in Fig. 2a, the high-resolution Co 2p spectrum can fitted into two major peaks (Co2p3/2 and Co2p1/2) and two shakeup satellites (indicated as ‘‘Sat.’’). The peaks at around 778.0 and 793.6 eV are corresponding to Co0, the two peaks at 779.5 and 794.8 eV can be ascribed to Co3+，while peaks around 780.8 and 796.3 eV are assigned to Co2+.49 In Fig. 2b, the Zn 2p spectrum reveals two evident peaks at 1021.1 and 1044.2 eV, which correspond to Zn 2p3/2 and Zn 2p1/2 of Zn species, respectively. The N 1s spectrum can be deconvolved into three peaks that are assigned to pyridinic nitrogen (398.0 eV), pyrrolic nitrogen (398.6 eV) and graphitic nitrogen (400.2 eV) in Fig. 2c. It is worth noting that the N species doping not only enhances the electron transfer, but also serve as an active site for electrochemical performance.50 As shown in Fig. 2d, the fitted C 1s peak clearly indicates the peak located in 284.1 eV for typical C-C bond of sp3-carbon, and the peaks at 284.9 eV and 288.1 eV respect to C-N and C=N species, respectively.51 All the above results manifest that Co3ZnC/Co-NCCP have been fabricated successfully by a simple annealing method. 6


Page 6 of 29

Page 7 of 29 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


The structural and morphological characteristics of Co3ZnC/Co-NCCP were further investigated by SEM and TEM. As shown in Fig. 3a and b, the as-prepared Co3ZnC/Co-NCCP shows a uniform polyhedral morphology with a diameter of about 400 nm, which is well inherited from the ZnCo-ZIFs. TEM further reveals that Co3ZnC/Co-NCCP polyhedra possesses a porous structure, in which the Co3ZnC and Co nanoparticles with the size of a few nanometers are homogenously rooted in the carbon framework. Note that a large number of NCNTs with the lengths of 30-60 nm are deeply embedded in the polyhedral surface. (Fig. 3c-e) It is commonly accepted that the cobalt nanoparticles are quickly formed at high temperature and a reductive atmosphere, followed by the catalytic growth of NCNTs.48 The polyhedral shell with interconnected NCNTs is very critical for the enlarged electrochemical surface area and the enhanced charge transport. In HRTEM images (Fig. 3f), the lattice fringes of 0.187 nm and 0.264 nm are consistent with the (200) plane of Co3ZnC and (220) plane of Co, respectively. Moreover, the Co3ZnC/Co nanoparticles are coated by ultrathin (~2 nm) graphitic carbon layers. The elemental mapping results (Fig 3g) further confirm that the C, Co, Zn and N elements are homogeneous distributed within the Co3ZnC/Co-NCCP. As shown in Fig. S3a-c, the Co3ZnC/Co nanoparticles distributed in nitrogen doped carbon polyhedra (denoted as Co3ZnC/Co-NCP) with a diameter of ~400 nm, unlike the Co3ZnC/Co-NCCP, the Co3ZnC/Co-NCP was synthesized by the conventional carbonization method using argon gas as inert atmosphere led to CNT-free polyhedra structure decorated with uniformly distributed Co3ZnC/Co nanoparticles. The measured XRD pattern of Co3ZnC/Co-NCP matches 7



Page 8 of 29

well with the Co3ZnC/Co-NCCP pattern (Fig. S3d). In addition, the single-metal Co-ZIF precursor (ZIF-67) was synthesized (Fig. S4a, b) and then directly carbonized at 600 oC for 2h under a flow of Ar/H2 to obtained Co nanoparticles embedded in nitrogen doped CNT-grafted carbon polyhedral structure (denoted as Co-NCCP). The Co-NCCP is similar to the morphology and size observed on Co3ZnC/Co-NCCP (Fig. S4c-d). The crystalline nature of the Co-NCCP is further confirmed by XRD in Fig. S5. The peaks can index with standard metallic Co (PDF 15-0806) and C (PDF 41-1487). The structural features of Co3ZnC/Co-NCCP, Co-NCCP and Co3ZnC/Co-NCP were also investigated by Raman spectroscopy. (Fig. S6) The intensity ratios of ID/IG value is determined to be 1.02 for the Co3ZnC/Co-NCCP, larger than that of the Co-NCCP (0.98) and Co3ZnC/Co-NCP (0.94), respectively. This indicates a higher graphitic degree and surface defect of Co3ZnC/Co-NCCP, suggesting a higher amount of N-doping into the carbon layer.52 The specific surface area and porosity of all the samples were investigated by N2 adsorption-desorption measurement. As shown in Fig. S7, all the samples exhibit a typical type-IV isotherm, indicating the existence of mesoporous structure. The specific surface areas of Co3ZnC/Co-NCCP, Co-NCCP and Co3ZnC/Co-NCP are determined to be 249.6, 185.1, and 151.3 m2·g

1

and pore size is

about 4.5, 4.6, and 8.5 nm, respectively. The relative large surface area and unique porous structure of Co3ZnC/Co-NCCP tend to offer more accessible active sites, which is likely to enhance the electrocatalytic performance. 53 The electrochemical activity of Co3ZnC/Co-NCCP towards OER was tested in a 8


Page 9 of 29 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


typical three-electrode system in 1 M KOH. As shown in Fig. 4a, glassy carbon (GC), Co-NCCP, Co3ZnC/Co-NCP and commercial RuO2 are also performed under the same conditions. As expected, the bare GC electrode exhibits little activity toward OER. The Co3ZnC/Co-NCCP showed the highest activity for oxygen evolution, getting a current density of 10 mA cm-2 at the overpotential of 295 mV, which is lower than that of Co-NCCP (387 mV), Co3ZnC/Co-NCP (400 mV), and even RuO2 (340 mV) . Such outstanding OER electrocatalytic activity is also manifested by the Tafel analysis (Fig. 4b), where the Tafel slope value of Co3ZnC/Co-NCCP (70 mV dec-1) is much lower than that of Co-NCCP (90 mV dec-1), Co3ZnC/Co-NCP (98 mV dec-1), and RuO2 (82 mV dec-1), indicating its efficient reaction kinetics for OER. Meanwhile, the performance of Co3ZnC/Co-NCCP is superior to some of the previously reported noble-metal-free electrocatalysts for OER in alkaline solution, which is summarized in Table S1. Furthermore, electrochemical impedance spectroscopy (EIS) was used to identify the reaction kinetics during the electrochemical process. As shown in Fig. S8, Co3ZnC/Co-NCCP possessed a charge-transfer resistance (Rct of 17.5 Ω), which is smaller than that for Co-NCCP (22.4 Ω) and Co3ZnC/Co-NCP (28.4 Ω), respectively. This suggested that the Co3ZnC/Co-NCCP has a much faster electron transfer process. We also investigated the electrochemically active surface area (ECSA) of various catalysts by evaluating the double-layer capacitance (Cdl) using cyclic voltammetry (CV) technique (Fig. S9a-c). As shown in Fig. S9d, the Cdl value of Co3ZnC/Co-NCCP is 10.4 mF cm-2, which is higher than that of Co-NCCP (6.2 mF cm-2) and Co3ZnC/Co-NCP (3.9 mF cm-2). This implies that the Co3ZnC/Co-NCCP 9



features higher effective surface area and more active sites, which would lead to the enhanced catalytic performance. In addition to the remarkable electrocatalytic activity, stability is another significant standard to assess the electrocatalyst. As displayed in Fig. 4c, after 1000 cycles, the linear sweep voltammetry (LSV) curves of the Co3ZnC/Co-NCCP shows a very small negative shift compared to that of the first cycle. Meanwhile, chronoamperometric measurement was evaluated at an overpotential of 300 mV. It can be seen in Fig. 4d, the Co3ZnC/Co-NCCP can retain 94% of its initial current after 10h testing, implying the high stability of the Co3ZnC/Co-NCCP in OER. Besides the excellent OER performance, Co3ZnC/Co-NCCP also shows desirable HER activity in 1.0 M KOH. It can be seen in Fig. 5a, the bare GC is ineffective toward hydrogen evolution. The as-prepared Co3ZnC/Co-NCCP exhibits superior HER performance, with a low overpotential of 188 mV to reach a current density of 10 mA cm-2, which is much lower than that of Co-NCCP (265 mV) or Co3ZnC/Co-NCP (337 mV), and close to commercial Pt/C catalyst (93 mV) at the same conditions. The corresponding Tafel slopes (Fig. 5b) are 159 mV dec-1, 171 mV dec-1 and 59 mV dec-1 for Co-NCCP, Co3ZnC/Co-NCP, and Pt/C catalyst, respectively. The Tafel slope of Co3ZnC/Co-NCCP is about 108 mV dec-1, implying a fast HER kinetics. The low overpotential and Tafel slope confirm its higher HER activity than those of many other previously reported HER catalysts. (Table S2). After 1000 cycles in alkaline solution, the LSV polarization of Co3ZnC/Co-NCCP exhibits an indistinguishable shift in current flow compared with the initial one (Fig. 5c), 10


Page 10 of 29

Page 11 of 29 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


suggesting its outstanding stability. Meanwhile, chronoamperometric measurement was measured at the potential of 200 mV. After 10h, the Co3ZnC/Co-NCCP product exhibits good long-term stability with 92.5% current retention (Fig. 5d). We further investigated the effect of various carburization temperature and Zn/Co molar ratio for ZnCo-ZIFs. The electrochemical results (Fig. S10) confirmed that the best performance is achieved by the product obtained at 600 oC with the Zn/Co molar ratio of 1:2. On the basis of the aforementioned result, the superior catalytic activity of Co3ZnC/Co-NCCP is mainly ascribed to the following reasons: (1) The Co3ZnC/Co interfaces could be synergistically active sites for OER and HER catalysis. In addition, the N-doped carbon frameworks have been proved to be also HER- and OER active.50 (2) The unique structure composed of N- doped CNT-grafted carbon polyhedral derived from ZnCo-ZIFs leads to a large electrochemical surface area and structural defects with more active sites for water splitting. (3) The uniformly distributed Co3ZnC/Co nanoparticles coated by graphene layers enable it to avoid the corrosion in the alkaline media. Due to the above reasons, Co3ZnC/Co-NCCP is expected to provide large surface area, efficient electron transfer, and abundant catalytic sites for high performance water splitting. Based on the above results, the Co3ZnC/Co-NCCP is demonstrated to be highly active and stable toward OER and HER in alkaline media. Therefore, we constructed a two-electrode configuration for overall water splitting with 1 M KOH electrolyte, where Co3ZnC/Co-NCCP coated onto carbon cloth was used as both the anode and 11



Page 12 of 29

cathode. The reference system using Pt/C-RuO2 and carbon cloth as cathode and anode were also tested. As shown in Fig. 6a, Co3ZnC/Co-NCCP requires an applied voltage of 1.65 V to achieve 10 mA cm-2. This result is very close to the 1.62 V of the Pt/C-RuO2 system and much lower than the 1.95 V for bare carbon cloth. The obvious H2 and O2 bubbles form both electrodes can be clearly observed in the inset of Fig. 6b. The long-term durability of Co3ZnC/Co-NCCP for overall water splitting was performed in 1 M KOH solution. The chronoamperometric response (Fig. 6b) shows that the current density can be well maintained without obvious deactivation after 10 h. As verified by TEM image (Fig. S11), the rhombic polyhedral shape with small embedded CNTs can be still obtained, revealing excellent structure robust after 10 h of electrolysis. All these results demonstrate the high electrochemical stability of the Co3ZnC/Co-NCCP catalyst.

3. CONCLUSIONS In

summary,

we

have

successfully

prepared

an

efficient

electrocatalyst

(Co3ZnC/Co-NCCP) by a simple and easily scalable one-pot thermal treatment of the ZnCo-ZIFs. The prepared porous Co3ZnC/Co-NCCP catalyst performed as a highly efficient and robust catalyst for both the HER and OER in alkaline media, affording a current density of 10 mA cm-2 at overpotentials of 295 mV for the OER and 188 mV for the HER. Furthermore, Co3ZnC/Co-NCCP exhibits overall water splitting at 10 mA cm-2 with only 1.65 V, which is close to the 1.62 V of the Pt/C-RuO2, along with excellent

durability.

The

outstanding

electrocatalytic

performance

of

Co3ZnC/Co-NCCP is considered to be a promising candidate to replace conventional 12


Page 13 of 29 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


noble metal in water splitting devices and this strategy can be extended to fabricate other nanomaterials for energy fields. ASSOCIATED CONTENT Supporting Information The supporting Information is available free of charge on the ACS Publications website. Further details about experiment section, XRD, SEM, TEM, BET, Raman, and electrochemical data. AUTHOR INFORMATION Corresponding Author *E-mail: [email protected] (Y Bai) *E-mail: [email protected] (KN Sun) Author Contributions All authors have given approval to the final version of the manuscript. Notes The authors declare no competing financial interest. Acknowledgements This project is supported by the National Natural Science Foundation of China (Grant No. 51203036) and the Scientific Research Foundation of Beijing Institute of Technology. REFERENCES (1) Turner, J. A. Sustainable Hydrogen Production. Science 2004, 305, 972-974.

13



(2) Lewis, N. S. Research Opportunities to Advance Solar Energy Utilization. Science 2016, 351, 353-363. (3) Jiao, Y.; Zheng, Y.; Jaroniec, M.; Qiao, S. Z. Design of Electrocatalysts for Oxygen- and Hydrogen-involving Energy Conversion Reactions. Chem. Soc. Rev. 2015, 44, 2060-2086. (4) Hunter, B. M.; Gray, H. B.; Müller, A. M. Earth-Abundant Heterogeneous Water Oxidation Catalysts. Chem. Rev. 2016, 116, 14120-14136. (5) Subbaraman, R.; Tripkovic, D.; Chang, K. C.; Strmcnik, D.; Paulikas, A. P.; Hirunsit, P.; Chan, M.; Greeley, J.; Stamenkovic, V.; Markovic, N. M. Trends in Activity for the Water Electrolyser Reactions on 3d M (Ni,Co,Fe,Mn) Hydr(oxy)oxide Catalysts. Nat. Mater. 2012, 11, 550-557 (6) Xu, Y. F.; Gao, M. R.; Zheng,Y. R.; Jiang, J.; and Yu, S. H. Nickel/Nickel(II) Oxide Nanoparticles Anchored Onto Cobalt(IV) Diselenide Nanobelts for the Electrochemical Production of Hydrogen. Angew. Chem., Int. Ed. 2013, 52, 8546-8550. (7) Jiao, F.; Frei, H. Nanostructured Cobalt Oxide Clusters in Mesoporous Silica as Efficient Oxygen-Evolving Catalysts. Angew. Chem., Int. Ed. 2009, 48, 1873-1876. (8) Xu, Y.; Kraft, M.; Xu, R.; Metal-free Carbonaceous Electrocatalysts and Photocatalysts for Water Splitting. Chem. Soc. Rev. 2016, 45, 3039-3052. (9) Zheng,Y. R.; Gao, M. R.; Yu, Z. Y.; Gao, Q.; Gao H. L.; Yu, S. H. Cobalt Diselenide Nanobelts Grafted on Carbon Fiber Felt: an Efficient and Robust 3D Cathode for Hydrogen Production. Chem. Sci. 2015, 6, 4594-4598 14


Page 14 of 29

Page 15 of 29 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


(10) Zhang, J.; Qu, L.; Shi, G.; Liu, J.; Chen, J.; Dai, L. N, P-Codoped Carbon Networks as Efficient Metal-free Bifunctional Catalysts for Oxygen Reduction and Hydrogen Evolution Reactions. Angew. Chem., Int. Ed. 2016, 55, 2230-2234. (11) Wang, J.; Li, K.; Zhong, H. X.; Xu, D.; Wang, Z. L.; Jiang, Z.; Wu Z. J.; Zhang, X. B. Synergistic Effect between Metal-Nitrogen-Carbon Sheets and NiO Nanoparticles for Enhanced Electrochemical Water-Oxidation Performance. Angew. Chem., Int. Ed. 2015, 54, 10530-10534. (12) Lee, Y.; Suntivich, J.; May, K. J.; Perry, E. E.; Shao-Horn,Y. Synthesis and Activities of Rutile IrO2 and RuO2 Nanoparticles for Oxygen Evolution in Acid and Alkaline Solutions. J. Phys. Chem. Lett. 2012, 3, 399-404. (13) Zou X.; Zhang, Y. Noble Metal-free Hydrogen Evolution Catalysts for Water Splitting. Chem. Soc. Rev. 2015, 44, 5148-5180. (14) Tang, H.; Yin, H.; Wang, J.; Yang, N.; Wang, D.; Tang, Z. Molecular Architecture of Cobalt Porphyrin Multilayers on Reduced Graphene Oxide Sheets for High-performance Oxygen Reduction Reaction. Angew. Chem., Int. Ed. 2013, 52, 5585-5589. (15) Zhang, X. L.; Zhang, J. B.; Wang, K. Codoping-Induced, Rhombus-Shaped Co3O4 Nanosheets as an Active Electrode Material for Oxygen Evolution. ACS Appl. Mater. Interfaces 2015, 7, 21745-21750. (16) Yu, Z.; Bai, Y.; Liu, Y. X.; Zhang, S. M.; Chen, D. D.; Zhang, N. Q.; Sun, K. N. Metal-Organic-Framework-Derived Yolk-Shell-Structured Cobalt-Based Bimetallic

15



Oxide Polyhedron with High Activity for Electrocatalytic Oxygen Evolution. ACS Appl. Mater. Interfaces 2017, 9, 31777-31785. (17) Ai, L. H.; Niu, Z. G.; Jiang, J. Mechanistic Insight into Oxygen Evolution Electrocatalysis of Surface Phosphate Modified Cobalt Phosphide Nanorod Bundles and Their Superior Performance for Overall Water Splitting. Electrochim. Acta 2017, 242, 355-363. (18) Liang, H. F.; Gandi, A. N.; Anjum, D. H.; Wang, X. B.; Schwingenschlögl, U.; Alshareef, H. N. Plasma-Assisted Synthesis of NiCoP for Efficient Overall Water Splitting. Nano Lett. 2016, 16, 7718-7725 (19) Liang, H. F.; Gandi, A. N.; Xia, C.; Hedhili, M. N.; Anjum, D. H.; Schwingenschlögl, U.; Alshareef, H. N. Amorphous NiFe-OH/NiFeP Electrocatalyst Fabricated at Low Temperature for Water Oxidation Applications. ACS Energy Lett. 2017, 2, 1035-1042. (20) Tian, T.; Huang, L.; Ai, L. H.; Jiang, J. Surface Anion-rich NiS2 Hollow Microspheres Derived from Metal-Organic Frameworks as a Robust Electrocatalyst for the Hydrogen Evolution Reaction. J. Mater. Chem. A 2017, 5, 20985-20992. (21) Xu, X.; Liang, H. F.; Ming, F. W.; Qi, Z. B.; Xie, Y. Q.; Wang, Z. C. Prussian Blue Analogues Derived Penroseite (Ni,Co)Se2 Nanocages Anchored on 3D Graphene Aerogel for Efficient Water Splitting. ACS Catal. 2017, 7, 6394-6399. (22) Jiang, J.; Liu, Q. X.; Zeng, C. M.; Ai, L. H. Cobalt/molybdenum carbide@N-doped carbon as a bifunctional electrocatalyst for hydrogen and oxygen evolution reactions. J. Mater. Chem. A 2017, 5, 1692-16935 16


Page 16 of 29

Page 17 of 29 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


(23) Zhang, Q.; Wang, Y.; Wang, Y.; Al-Enizi, A. M.; Elzatahry, A. A.; Zheng, G. Myriophyllum-like Hierarchical TiN@Ni3N Nanowire Arrays for Bifunctional Water Splitting Catalysts. J. Mater. Chem. A 2016, 4, 5713-5718. (24) Vrubel, H.; Hu, X. Molybdenum Boride and Carbide Catalyze Hydrogen Evolution in both Acidic and basic Solutions. Angew. Chem., Int. Ed. 2012, 51, 12703-12706. (25) Wu, H. B.; Xia, B. Y.; Yu, L.; Yu, X. Y.; and Lou, X. W. Porous Molybdenum Carbide Nano-octahedrons Synthesized via Confined Carburization in Metal-Organic Frameworks for Efficient Hydrogen Production. Nat. Commun. 2015, 6, 6512 (26) Cui, W.; Cheng, N. Y.; Liu, Q.; Ge, C. J.; Asiri, A. M.; Sun, X. P. Mo2C Nanoparticles Decorated Graphitic Carbon Sheets: Biopolymer Derived Solid-State Synthesis and Application as an Efficient Electrocatalyst for Hydrogen Generation. ACS Catal. 2014, 4, 2658-2611. (27) Xu, K.; Ding, H.; Lv, H.; Chen, P.; Lu, X.; Cheng, H.; Zhou, T.; Liu, S.; Wu, X.; Wu, C.; Xie, Y. Dual Electrical-Behavior Regulation on Electrocatalysts Realizing Enhanced Electrochemical Water Oxidation. Adv. Mater. 2016, 28, 3326-3332. (28) Vrubel, H.; Hu, X. L.; Molybdenum Boride and Carbide Catalyze Hydrogen Evolution in both Acidic and basic Solutions. Angew. Chem. Int. Ed. 2012, 51, 12703-12706. (29) Lin, H.; Liu, N.; Shi, Z.; Guo, Y.; Tang, Y.; Gao, Q. Nanowires: Cobalt-Doping in Molybdenum-Carbide Nanowires Toward Efficient Electrocatalytic Hydrogen Evolution. Adv. Funct. Mater. 2016, 26, 5590-5598. 17



Page 18 of 29

(30) Wan, C.; Leonard, B. M. Iron-Doped Molybdenum Carbide Catalyst with High Activity and Stability for the Hydrogen Evolution Reaction. Chem. Mater. 2015, 27, 4281-4288. (31) Ma, L. B.; Shen, X. P.; Zhu, J.; Zhu, G. X.; Ji, Z. Y.; CoP Nanoparticles Deposited on Reduced Graphene Oxide Sheets as an Active Electrocatalyst for the Hydrogen Evolution Reaction. J. Mater. Chem. A 2015, 3, 11066-11073. (32) Tang, Y. J.; Liu, C. H.; Huang, W.; Wang, X. L.; Dong, L. Z.; Li, S. L.; Lan, Y. Q. Bimetallic Carbides-Based Nanocomposite as Superior Electrocatalyst for Oxygen Evolution Reaction. ACS Appl. Mater. Interfaces 2017, 20, 16977-16985. (33) Liu, Y. P.; Yu, G. T.; Li, G. D.; Sun, Y. H.; Asefa, T.; Chen, W.; Zou, X. X.; Coupling

Mo2C

with

Nitrogen-Rich

Nanocarbon

Leads

to

Efficient

Hydrogen-Evolution Electrocatalytic Sites. Angew. Chem. Int. Ed. 2015, 54, 10752 -10757. (34) Feng, J. X.; Xu, H.; Dong, Y. T.; Ye, S. H.; Tong, Y. X.; Li, G. R. FeOOH/Co/FeOOH Hybrid Nanotube Arrays as High-Performance Electrocatalysts for the Oxygen Evolution Reaction. Angew. Chem. 2016, 128, 3758-3762. (35) Hu, H.; Guan, B.; Xia, B.; Lou, X. W. Designed Formation of Co3O4/NiCo2O4 Double-Shelled Nanocages with Enhanced Pseudocapacitive and Electrocatalytic Properties. J. Am. Chem. Soc. 2015, 137, 5590-5595. (36) Su, J. W.; Xia, G. L.; Li, R.; Yang, Y.; Chen, J. T.; Shi, R. H.; Jiang P.; Chen, Q. W. Co3ZnC/Co Nano-Heterojunctions Encapsulated in Nitrogen-Doped Graphene

18


Page 19 of 29 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Layers Derived from PBAs as Highly Efficient Bi-Functional Electrocatalysts for Both OER and ORR. J. Mater. Chem. A 2016, 4, 9204-9212. (37) Su, J.; Zhang, Y.; Xu, S.; Wang, S.; Ding, H.; Pan, S.; Wang, G.; Li G.; Zhao, H. Highly

Efficient

and

Recyclable

Triple-Shelled

Ag@Fe3O4@SiO2@TiO2

Photocatalysts for Degradation of Organic Pollutants and Reduction of Hexavalent Chromium ions. Nanoscale 2014, 6, 5181-5192. (38) Jin, H. Y.; Wang, J.; Su, D. F.; Wei, Z. Z.; Pang, Z. F.; and Wang, Y. In situ Cobalt-Cobalt

Oxide/N-doped

Carbon

Hybrids

as

Superior

Bifunctional

Electrocatalysts for Hydrogen and Oxygen Evolution. J. Am. Chem. Soc. 2015, 137, 2688-2694. (39) Shang, L.; Yu, H.; Huang, X.; Bian, T.; Shi, R.; Zhao, Y.; Waterhouse, G.I.; Tung, C. H.; Zhang, T. Nitrogen-Doped Porous Carbon Nanosheets Templated from g-C3N4 as Metal-Free Electrocatalysts for Efficient Oxygen Reduction Reaction. Adv. Mater. 2016, 28, 1668. (40) Li, J. B.; Yan, D.; Lu, T.; Yao, Y. F.; Pan, L. K. An Advanced CoSe Embedded Within Porous Carbon Polyhedra Hybrid for High Performance Lithium-ion and Sodium-ion Batteries. Chem. Eng. J. 2017, 325, 14-24 (41) Tang, J.; Salunkhe, R. R.; Liu, J.; Torad, N. L.; Imura, M.; Furukawa, S.; Yamauchi, Y. Thermal Conversion of Core-Shell Metal-Organic Frameworks: A New Method for Selectively Functionalized Nanoporous Hybrid Carbon. J. Am. Chem. Soc. 2015, 137, 1572-1580.

19



Page 20 of 29

(42) Yu, X. Y.; Yu, L.; Wu, H. B.; Lou, X. W. Formation of Nickel Sulfide Nanoframes from Metal-Organic Frameworks with Enhanced Pseudo capacitive and Electrocatalytic Properties. Angew. Chem., Int. Ed. 2015, 54, 5331-5335. (43) Ai, L. H.; Tian, T.; Jiang, J. Ultrathin Graphene Layers Encapsulating Nickel Nanoparticles

Derived

Metal-Organic

Frameworks

for

Highly

Efficient

Electrocatalytic Hydrogen and Oxygen Evolution Reactions. ACS Sustainable Chem. Eng. 2017, 5, 4771-4777. (44) Kim, J.; Young, C.; Lee, J.; Park, M. S.; Shahabuddin, M.; Yamauchi Y.; Kim, J. H. CNTs Grown on Nanoporous Carbon from Zeolitic Imidazolate Frameworks for Supercapacitors. Chem. Commun. 2016, 52, 13016-13019. (45) Zhou, W. J.; Lu, J.; Zhou, K.; Yang, L. J.; Ke, Y. T.; Tang, Z. H.; Chen, S. W. Hierarchical Spheres Constructed by Defect-Rich MoS2/Carbon Nanosheets for Efficient Electrocatalytic Hydrogen Evolution. Nano Energy 2016, 28, 143-150. (46) Kim, J. H.; Young, C.; Lee, J.; Heo, Y. U.; Park, M. S.; Hossain, M. S.; Yamauchi, Y.; Kim, J. H. Nanoarchitecture of MOF-derived Nanoporous Functional Composites for Hybrid Supercapacitors. J. Mater. Chem. A 2017, 5, 15065-15072. (47) Aijaz, A.; Masa, J.; Rösler, C.; Xia, W.; Weide, P.; Botz, A. J. R.; Fischer, R.A.; Schuhmann, W.; Muhler, M. Co@Co3O4 Encapsulated in Carbon Nanotube-Grafted Nitrogen-Doped Carbon Polyhedra as an Advanced Bifunctional Oxygen Electrode. Angew. Chem. Int. Ed. 2016, 55, 4087-4091.

20


Page 21 of 29 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


(48) Xia, B. Y.; Yan,Y.; Li, N.; Wu, H. B.; Lou, X. W.; Wang, X. A Metal-Organic Framework-Derived Bifunctional Oxygen Electrocatalyst. Nat. Energy 2016, 1, 15006-15014. (49) Chen, T.; Cheng, B. R.; Chen, R. P.; Hu, Y.; Lv, H. L.; Zhu, G. Y.; Wang, Y. R.; Ma, L. B.; Liang, J.; Tie, Z. X.; Jin, Z.; Liu, J. Hierarchical Ternary Carbide Nanoparticle/Carbon NanotubeInserted N Doped Carbon Concave-Polyhedrons for Efficient Lithium and Sodium Storage. ACS Appl. Mater. Interfaces 2016, 8, 26834-26841 (50) Zheng, Y.; Jiao, Y.; Zhu, Y.; Li, L. H.; Han, Y.; Chen, Y.; Du, A.; Jaroniec, M.; and Qiao , S. Z. Hydrogen Evolution by a Metal-free Electrocatalyst. Nat. Commun. 2014, 5, 3783. (51) Li, Y. J.; Fan, J. M.; Zheng M. S.; Dong, Q. F.; A Novel Synergistic Composite with Multi-Functional Effects for High-Performance Li-S Batteries. Energy Environ. Sci. 2016, 9, 1998-2004. (52) Ferrari, A. C.; Basko, D. M.; Raman spectroscopy as a versatile tool for studying the properties of graphene. Nat. Nanotechnol. 2013, 8, 235-246. (53) Hou, Y.; Wen, Z.; Cui, S.; Ci, S.; Mao S.; Chen, J. An Advanced Nitrogen‐ Doped Graphene/Cobalt‐Embedded Porous Carbon Polyhedron Hybrid for Efficient Catalysis of Oxygen Reduction and Water Splitting Adv. Funct. Mater. 2015, 25, 872-882

21



Scheme. 1 Illustration of the synthesis procedure for Co3ZnC/Co-NCCP.

22


Page 22 of 29

Page 23 of 29 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Fig. 1 (a) XRD patterns and (b) EDS spectra of Co3ZnC/Co-NCCP.

23



Fig. 2 High-resolution XPS spectra of (a) Co 2p; (b) Zn 2p; (c) N 1s and (d) C 1s of Co3ZnC/Co-NCCP.

24


Page 24 of 29

Page 25 of 29 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Fig. 3 (a, b) SEM images, (c-e) TEM images, (f) HRTEM image and (g) EDX element mapping of Co3ZnC/Co-NCCP.

25



Fig. 4 (a) LSV curves and (b) Tafel plots of Co3ZnC/Co-NCCP, Co-NCCP, Co3ZnC/Co-NCP and RuO2 in 1M KOH. (c) LSV curves of the Co3ZnC/Co-NCCP obtained before and after 1000 potential cycles. (d) Time-dependent current density (i-t) curves of the Co3ZnC/Co-NCCP at an overpotential of 300 mV.

26


Page 26 of 29

Page 27 of 29 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Fig. 5 (a) LSV curves and (b) Tafel plots of Co3ZnC/Co-NCCP, Co-NCCP, Co3ZnC/Co-NCP and Pt/C in 1M KOH. (c) LSV curves of the Co3ZnC/Co-NCCP before and after 1000 potential cycles. (d) Time-dependent current density (i-t) curves over the Co3ZnC/Co-NCCP at the overpotential of 200 mV.

27



Fig. 6 (a) Polarization curves for water electrolysis of Co3ZnC/Co-NCCP|| Co3ZnC/Co-NCCP , Pt/C||RuO2 and carbon cloth at a scan rate of 5 mV s-1 in 1 M KOH solution. (b) Time-dependent current density curve of Co3ZnC/Co-NCCP as a high-performance catalyst for the overall water splitting.

28


Page 28 of 29

Page 29 of 29 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60


Table of Contents Graphic

29


Co Embedded in

Recommend Documents