Subscriber access provided by HKU Libraries
Article
Continuous and Inexpensive Monitoring of Non-Purgeable Organic Carbon by Coupling High-Efficiency Photo-oxidation Vapor Generation to Miniaturized Point Discharge Optical Emission Spectrometry Shu Zhang, Yunfei Tian, Hongling Yin, Yubin Su, Li Wu, Xiandeng Hou, and Chengbin Zheng Environ. Sci. Technol., Just Accepted Manuscript • DOI: 10.1021/acs.est.7b01064 • Publication Date (Web): 14 Jul 2017 Downloaded from http://pubs.acs.org on July 14, 2017
Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a free service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are accessible to all readers and citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.
Environmental Science & Technology is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.
Page 1 of 28
Environmental Science & Technology
1
Continuous and Inexpensive Monitoring of Non-Purgeable
2
Organic Carbon by Coupling High-Efficiency
3
Photo-oxidation Vapor Generation to Miniaturized Point
4
Discharge Optical Emission Spectrometry
5
Shu Zhang1, Yunfei Tian3, Hongling Yin2, Yubin Su1, Li Wu3, Xiandeng Hou1,3, and
6
Chengbin Zheng1*
7 8 9 10 11
1
Key Laboratory of Green Chemistry & Technology of MOE, College of Chemistry,
Sichuan University, Chengdu, Sichuan 610064, China 2
College of Resources and Environment, Chengdu University of Information
Technology, Chengdu, Sichuan 610225, China 3
Analytical & Testing Center, Sichuan University, Chengdu, Sichuan 610064, China
12
*Corresponding author:
13
Fax: +86 28 85412907; Phone: +86-28-85415810
14
E–mail:
[email protected] (C. B. Zheng)
1
ACS Paragon Plus Environment
Environmental Science & Technology
1
ABSTRACT
2
Currently, no applicable analyzers are available to accomplish online and continuous
3
monitoring of organic pollution, which is one of the most important factors
4
contributing to water shortages around the world, particularly in developing countries.
5
In this work, a sensitive, miniaturized, inexpensive, on-line and continuous
6
non-purgeable organic carbon (NPOC) analysis system was developed for the
7
continuous monitoring of such organic pollution. This system consists of a specially
8
designed and high efficiency UV photo-oxidation vapor generation (HE-POVG)
9
reactor and a miniaturized, low power (7 W) point discharge microplasma optical
10
emission spectrometer (PD-OES). Organics present in sample or standard solutions
11
are pumped to the HE-POVG and efficiently converted into CO2, which is separated
12
and further transported to the PD-OES for NPOC analysis via the highly sensitive
13
detection of carbon atomic emission at 193.0 nm. Under optimal conditions, a limit of
14
detection (LOD) of 0.05 mg L-1 (as C) is obtained, with precision better than 5.0%
15
(relative standard deviation, RSD) at 5 mg L-1. This system overcomes many
16
shortcomings associated with conventional COD or TOC analyzers such as long
17
analysis time, use of expensive and toxic chemicals, production of secondary toxic
18
waste, requirement of large, power consuming and expensive instrumentation and
19
difficulties implementing continuous, online and continuous monitoring. The system
20
was successfully applied to the sensitive and accurate determination of NPOC in
21
various water samples and for the continuous monitoring of such organic pollution in
22
tap water.
23
2
ACS Paragon Plus Environment
Page 2 of 28
Page 3 of 28
Environmental Science & Technology
1
INTRODUCTION
2
Water scarcity is one of the toughest challenges facing the world today and about 600
3
million people are at risk of disease or death because of insufficient clean water.1,2
4
Besides population growth and climate change, organic pollution produced from
5
human activities exacerbates this scarcity.3-5
6
Chemical oxygen demand (COD), biochemical oxygen demand (BOD) and total
7
organic carbon (TOC) are the most used methodologies for assessing organic
8
pollution 6-8. The conventional COD and BOD methods usually involve tedious and
9
time-consuming reflux (2-3 hours) and incubation (5 days) processes, respectively.
10
Moreover, the COD methods require highly toxic (Cr6+ and Hg2+), expensive (Ag+) or
11
corrosive (H2SO4) reagents. Recently, many methods based on electrocatalytic,9,10
12
photocatalytic11-14 and photoelectrochemical15-18 oxidation principles have been
13
developed for COD analysis. These methods simplified analytical procedures and
14
minimized the consumption of toxic chemicals. It is noteworthy that both COD and
15
BOD are indirect methods and may be severely interfered by some oxidizable ions.
16
Compared to COD and BOD methods, TOC is the most suitable method for the
17
evaluation of organic pollution of water because it not only significantly reduces the
18
use of toxic chemicals but also directly express a measure of organic pollution.6
19
Almost all TOC measurements include oxidation of organics to CO2 by chemical
20
oxidation,19
21
using noble metal catalysts (Pt or Pd), and detection of the generated CO2 with
22
nondispersive infrared (NDIR) absorption spectrometry,22,25 thermal conductivity,26
23
electrolytic conductivity,27 titrimetry28 or ion chromatography29. Despite such
24
advantages of TOC, there still remain a number of shortcomings in both the oxidation
25
and the detection steps. Chemical and photo-oxidation usually lead to incomplete
26
oxidation of organics and underestimate the TOC value. Although HTC offers higher
27
oxidation efficiency than other methods, this technique is still handicapped by the use
28
of expensive catalysts and operation at high temperature. For CO2 detection,
29
gravimetry and titrimetry are not sensitive and electrolytic conductivity is frequently
UV photo-oxidation20,21 or high-temperature combustion (HTC)22-24
3
ACS Paragon Plus Environment
Environmental Science & Technology
1
precluded by the ionic compounds produced from the degradation of the organics
2
(particular for nitrogen and sulfur containing compounds). Notably, almost all of the
3
TOC techniques require relatively large and expensive laboratory instrumentation
4
which makes them unaffordable in developing countries, whereas water crises caused
5
by organic pollution typically occurs in these countries because of their rapid
6
economic development. Moreover, there are currently no applicable analyzers for the
7
online and continuous monitoring of TOC. Therefore, there is an urgent need to
8
develop an inexpensive and continuous TOC monitoring system. Recently, we have
9
coupled microwave assisted oxidation vapor generation (MOVG) to dielectric barrier
10
discharge (DBD) optical emission spectrometry (OES) for TOC analysis.30 MOVG
11
can significantly improve the oxidation efficiency of organics and reduce the analysis
12
time. However, conventional microwave oven heating is power consuming, expensive
13
and automatically turned off when the oven is overheated, preventing its use for
14
continuous monitoring. Meanwhile, careful operation and complex heating devices
15
are also required to obtain satisfactory analytical performance because of the low
16
excitation capacity of the DBD. Since purgeable organic carbon (POC) is also
17
removed during the acidification and purging procedure used to eliminate the
18
interference of total inorganic carbon (TIC)
19
methods is non-purgeable organic carbon (NPOC).
20
In this work, an inexpensive and online system coupling a high-efficiency UV
21
photo-oxidation vapor generation (HE-POVG) reactor to a miniaturized point
22
discharge (PD) optical emission spectrometer was developed for the determination
23
and continuous monitoring of NPOC. The high-efficiency POVG was realized using a
24
special photo-oxidation reactor with high UV transmittance from a low-pressure
25
mercury lamp wherein conversion of organics to CO2 was more efficient than
26
conventional photo-oxidation reactors.31 Moreover, the PD possesses higher
27
excitation capability than a DBD32 and thus offers higher sensitivity for the NPOC
28
detection. To the best of our knowledge, this is the first report of use of HE-POVG
29
coupled to a PD-OES for NPOC analysis.
6,21
, the TOC determined by most of
4
ACS Paragon Plus Environment
Page 4 of 28
Page 5 of 28
Environmental Science & Technology
1
EXPERIMENTAL SECTION
2
Instrumentation. The HE-POVG-PD-OES system is presented in Figure 1 and
3
consists mainly of a flow injection (FI) or continuous flow HE-POVG reactor and a
4
point discharge optical emission spectrometer equipped with a commercial hand-held
5
charge coupled device (CCD) spectrometer (Maya 2000 Pro, Ocean Optics Inc.,
6
Dunedin, FL) with 200 - 400 nm of spectral range and 0.4 nm of spectral resolution.
7
The FI-HE-POVG reactor consisted of two channel peristaltic pumps (BT100-02,
8
Baoding Qili Precision Pump Company, Ltd., Baoding, China), a six port injection
9
valve (Genuine Rheodyne Co., USA) equipped with a 0.5 mL of sampling loop, a
10
high-efficiency photo-oxidation reactor (Beijing Titan Instruments Co., Beijing,
11
China), a quartz gas liquid separator (GLS) and a quartz dryer filled with CaCl2. The
12
photo-oxidation reactor was similar to the one reported in previous work,31 which
13
included a quartz reaction tube (93 cm length × 1.0 mm i.d. × 2.0 mm o.d.) and a 19
14
W low pressure mercury vapor UV lamp. The reaction tube was folded three times to
15
increase the residence time of sample solution in UV irradiation zone within the body
16
of the mercury lamp. The reactor was enclosed in aluminum foil to protect the
17
operator from exposure to UV irradiation and reflect the UV back to the reaction
18
solution, further improving the oxidation efficiency. It should be emphasized that the
19
photo-oxidation reactor is quite different from that previously reported19,21 because its
20
reaction tube does not surround the exterior of the UV lamp but is inserted and sealed
21
within the lamp discharge, which significantly improves the transmission of vacuum
22
UV light and allows highly efficient and uniform UV irradiation of the sample
23
solution from all directions. This reactor generates both 254 nm and 185 nm of UV
24
light, significantly improving the generation of strong oxidants (i.e., hydroxyl radical)
25
for increasing the oxidation efficiencies of organics. To demonstrate the superior
26
performance of the HE-POVG reactor, a conventional photo-oxidation reactor
27
consisting of a coiled quartz tube (90 cm length × 2.0 mm i.d. × 3.0 mm o.d.) wrapped
28
around a 20 W low pressure mercury vapor UV lamp (Philips, Holland) was also used
29
for NPOC analysis. The GLS was connected to the HE-POVG reactor and the 5
ACS Paragon Plus Environment
Environmental Science & Technology
1
PD-OES via silica tubing. The setup of the PD-OES is the same as that reported in the
2
previous work32, which is briefly described together with the setup of the DBD-OES
3
in Section 1 and 2 of the Supporting Information (SI). A picture of FI-HE-POVG-OES
4
system is presented in Figure S1 (See section 3 of the SI). The continuous HE-POVG
5
eliminated the six port injection valve but added the quartz GLS for online removal of
6
the generated CO2 from any inorganic carbon before the photo-oxidation of organics.
7
The full instrumental setup for continuous HE-POVG-PD-OES is described in Figure
8
S2.
9
The accuracy and practicality of this approach was validated via comparison of the
10
analytical results obtained using the proposed system and a HTC-NDIR (Analytikjena
11
multi N/C 2100 analyzer, Germany). The typical operation parameters for the
12
HTC-NDIR analysis are: furnace temperature, 680 oC; sample volume, 200 µL;
13
oxygen purge time, 180 s; and oxygen gas flow rate, 200 mL min-1.
14
Reagents. All chemicals were of at least analytical-reagent grade. 18 MΩ cm
15
deionized water (DIW) produced from a water purification system (Chengdu
16
Ultrapure Technology Company, Ltd., Chengdu, Sichuan Province, China.) was
17
boiled to remove the residual CO2 prior to its use for preparation of all solutions. A
18
10000 mg L-1 of NPOC (as C) standard stock solutions were prepared by dissolving
19
analytical-reagent grade potassium hydrogen phthalate (KHP, C8H5KO4, Kelong
20
Reagent Company, Chengdu, China) and stored in refrigerator at 4 oC before analysis.
21
Standard solutions containing various concentrations of NPOC were prepared daily by
22
diluting the stock solution with DIW. Argon (99.99%) obtained from Qiaoyuan Gas
23
Company (Chengdu, Sichuan Province, China) was simultaneously employed as a
24
carrier and discharge gas.
25
Sample Collection. Water samples were collected from artificial lakes located in 9
26
municipal parks and rivers of Chengdu city. The sampling map and sites of the lakes
27
are shown in Figure S3. All the samples were collected in 250 mL glass bottles and
28
stored in an ice box. These samples were analyzed with the proposed system and the
29
HTC-NDIR instrument as soon as possible after being transported to the laboratory.
30
Detailed information about sample preparation is presented in Section 6 of the SI. 6
ACS Paragon Plus Environment
Page 6 of 28
Page 7 of 28
Environmental Science & Technology
1
Sample Analysis by FI-HE-POVG-PD-OES. The procedure for flow injection
2
NPOC analysis is described as follows. The standard or sample solution was acidified
3
using 10% phosphoric acid and purged for 3 min with 200 mL min-1 of Ar carrier gas
4
prior to NPOC analysis. The pretreated solution was initially pumped to a 0.5 mL
5
sample loop through a six-port valve. Then the valve was activated to pass DIW
6
carrier solution so as to flush the solution together with oxidizing solution (30% (m/v)
7
of Na2S2O8) through the photo-oxidation reactor for UV irradiation. Organics were
8
efficiently converted to CO2 in this process. In our previous work, the reaction
9
solution had to pass through a complex ice bath to ensure no condensed liquid
10
droplets were transported to the DBD-OES, whereas it was directly swept into the
11
GLS for the separation of CO2 in this work, simplifying the instrumental setup. The
12
CO2 passed through the dryer before entering the PD-OES for the detection of carbon
13
atomic emission
14
Online and Continuous Monitoring of NPOC. The main purpose of this work is to
15
develop a continuous monitoring system for the real time monitoring of NPOC in
16
water system. In this case, the sampling tube was directly inserted into the pumped
17
water flow and then the water sample was pumped to mix with 10% of phosphoric
18
acid in a coil reaction tube (40 cm length × 2.0 mm i.d. × 3.0 mm o.d.) for the
19
efficient reaction. The reaction mixture was swept into the first GLS wherein an Ar
20
carrier gas was introduced to separate the generated CO2. It is worthwhile to note that
21
a magnetic stir bar was put in the first GLS to stir the mixture for the completely
22
removal of the CO2 from the TIC in the water sample. The mixture was further
23
pumped into the photo-oxidation reactor together with the Na2S2O8 solution to
24
produce CO2. Then CO2 was separated by the second GLS and finally detected by
25
PD-OES.
26
RESULTS AND DISCUSSION
27
Preliminary Studies and Practicality of UV-POVG-PD-OES. The simple and
28
inexpensive determination of TOC can be obtained by coupling MOVG to
29
miniaturized DBD-OES.30 However, the MOVG-DBD-OES cannot be easily used for 7
ACS Paragon Plus Environment
Environmental Science & Technology
1
continuous monitoring of NPOC because of the drawbacks of a conventional
2
microwave heating device. Despite its low oxidation capability, a conventional UV
3
photo-oxidation reactor is frequently used for the online and continuous degradation
4
of organics.20,33,34 As a consequence, an initial experiment was undertaken to use the
5
conventional photo-oxidation reactor as an alternative to the MOVG to realize the
6
continuous NPOC analysis with DBD-OES. A 0.5 mL aliquot of 50 mg L-1 (as C)
7
KHP solution was analyzed; results are shown in Figure 2a. Unexpectedly, the
8
specific carbon emissions at either 193.0 or 247.8 nm were not detected by the
9
DBD-OES system. It is possible that both the low oxidation efficiency of the
10
conventional photo-oxidation reactor and the weak excitation capability of the DBD
11
microplasma caused this result. Since the PD microplasma has higher excitation
12
energy compared to the DBD,32 it replaced the DBD source and was coupled with the
13
conventional photo-oxidation reactor for NPOC analysis. Interestingly, the specific
14
carbon atomic emission (Figure 2a) was obviously observed with this setup, although
15
the sensitivity is still much lower than that reported in previous work using the
16
MOVG-DBD-OES. Sensitivity should be further improved if photo-oxidation
17
efficiencies of organics are enhanced by using the high-efficiency photo-oxidation
18
reactor. Tao et al.31 reported a home-made photo-oxidation reactor with remarkably
19
high oxidation capability. This reactor could completely decompose persistent organo-
20
arsenic compounds (e.g. arsenobetaine) to As (V) in 42 s, even in the absence of
21
added oxidant, whereas over 6 h was needed for this complete decomposition with a
22
conventional photo-oxidation reactor. Thus, a similar HE-POVG reactor was used to
23
couple with the PD-OES for NPOC analysis. As can be seen from Figure 2a and b, the
24
intensities of the carbon atomic emission spectra are enhanced about 18-fold
25
compared to those obtained using the conventional photo-oxidation reactor. According
26
to previous work31, this remarkable improvement arises primarily due to the vacuum
27
ultraviolet light at 185 nm and its high transmittance to the sample in this system.
28
Actually, the photo-oxidation efficiency is increased by increasing the reaction
29
temperature.35 To gain further insight into the HE-POVG reactor, a handheld infrared
30
thermometer was used to measure the temperatures of the reaction tubes of the 8
ACS Paragon Plus Environment
Page 8 of 28
Page 9 of 28
Environmental Science & Technology
1
photo-oxidation reactors. The temperature of the HE-POVG reactor (50 ± 5 °C) was
2
much higher than that of conventional photo-oxidation reactor (30 ± 2 °C), suggesting
3
that the significant improvement of oxidation efficiency arises not only because of the
4
vacuum ultraviolet irradiation, but also due to the high reaction temperature.
5
It is noteworthy that although both carbon emission lines at 193.0 and 247.8 nm can
6
be observed with this system, emission at 193.0 nm was finally chosen for the NPOC
7
analysis because many strong emission bands in the spectral range 230−270 nm
8
(those belonged to the NO molecule emission bands) were detected,32,36 which lead to
9
serious spectral interference for the NPOC analysis. The linear coefficient obtained by
10
the proposed system after analysis of a series of standard solutions containing various
11
concentrations of KHP was better than 0.99 (Figure 2c), further supporting the
12
feasibility and practicality of the HE-POVG-PD-OES for NPOC analysis.
13
Optimization of Experimental Parameters and Investigation of Oxidation
14
Efficiencies. In order to improve the analytical performance of the proposed system,
15
both the operation conditions of the PD-OES (discharge voltage, discharge gap and
16
flow rate of carrier gas) and UV photo-oxidation system (flow rate of carrier solution
17
and concentration of Na2S2O8) were carefully optimized using 10.0 mg L-1 (as C)
18
NPOC standard solutions. Results are summarized in Table S1 (See sections 7 of the
19
SI).
20
Since the organics contained in real water samples are quite different, the oxidation
21
efficiencies of various organic compounds may severely affect the accuracy of the
22
method. Therefore, three approaches were utilized to investigate the effect of the
23
kinds of the organics in water on the oxidation efficiency of NPOC. Firstly, the
24
oxidation efficiencies of 20 organic compounds (all contain 50 mg L-1 of NPOC (as
25
C)) were investigated using the HE-POVG-PD-OES, as shown in Figure 3a. The
26
results show that the relative oxidation efficiencies compared to that of KHP (set to
27
100%) range from 88 to 110%, indicating that any difference between the oxidation
28
efficiencies of the tested organics is not evident. Secondly, a series of solutions
29
containing various concentrations (as C) of different organics were analyzed by the
30
proposed system. The results summarized in Figure 3b show a calibration curve with 9
ACS Paragon Plus Environment
Environmental Science & Technology
1
a linear coefficient of 0.995, showing the proposed system is capable of oxidizing
2
various organic compounds uniformly. Actually, some organics in real water are more
3
complex than these 20 organics, for example humic acids. Finally, the oxidation
4
efficiencies of humic acid or NPOC in real river water were studied. Since the exact
5
concentrations of humic acid and NPOC value are unknown, the oxidation efficiency
6
(En) is thus defined as:
7
E
n
%
I1
I n 100 I2 I3 I4 I5
8
Where In is the intensity (a.u.) of carbon atomic emission obtained from the n-th
9
photo-oxidation (n=1, 2, 3, 4 or 5). As shown in Figure S6 (See Section 8 of SI), the
10
oxidation efficiencies of humic acid and NPOC in river water from the first oxidation
11
are higher than 85%. Meanwhile, the oxidation efficiencies of 20 mg L-1 KHP were
12
also evaluated by this method and the results summarized in Figure S6 show that its
13
first oxidation efficiency is 96%. These results indicate that the oxidation efficiencies
14
for most of the dissolved organic matter even for humic acid are higher than 86%
15
compared to that of KHP, implying that the HE-POVG-PD-OES can be employed for
16
accurate NPOC analysis, regardless of the chemical forms of organic pollutants
17
present in water samples.
18
Effect of Acidified and Purged Procedures. In order to eliminate the interference
19
from inorganic carbon, acidification and purging steps are required prior to NPOC
20
analysis. A river water and a tap water were used to study the effect of inorganic
21
carbon on NPOC analysis via analyzing these samples with or without such steps. The
22
results are summarized in Figure 4 and show that the inorganic carbon present in the
23
sample provides a serious interference on NPOC analysis. Fortunately, a simple
24
pretreatment, including an acidification of sample using 10% (v/v) of phosphoric acid
25
and a 3 min purge with 200 mL min-1 of Ar is able to efficiently eliminate this
26
interference. These samples were also analyzed without acidification but with 3 min
27
of purge, as shown in Figure 4. The results show that there is no obvious difference
28
between the responses obtained with or without the purge, implying that the purgeable
29
organic carbon is negligible in many surface and ground waters. These results agree 10
ACS Paragon Plus Environment
Page 10 of 28
Page 11 of 28
Environmental Science & Technology
1
well with those reported in previous studies22 and that the NPOC obtained by the
2
proposed method can be substituted for TOC in these sample analyses.
3
Interferences. It is well-known that interferences arising from co-existing anions,
4
particularly from chloride ion, present a serious problem with conventional COD
5
methods. For example, Dharmadhikari et al.8 reported that chloride ions seriously
6
interfere with the COD measurement using Cr(VI) as oxidizing reagent at
7
concentrations higher than 2 g L-1, making these methods unsuitable for the COD
8
analysis of the sample containing high concentration of chloride ions, such as sea
9
water. Our work30 showed that the MOVG-DBD-OES could be directly utilized for
10
the TOC analysis of seawater because it possessed much higher resistance to
11
interference by Cl-, even at concentrations as high as 10 g L-1. However, UV
12
persulfate oxidation of organics is different from that using microwave assisted
13
oxidation. Therefore, the effects of some common anions (NO3-, PO43-, SO42-, and Cl-)
14
and cations (Na+, K+, Fe3+, Zn2+, Mn2+, Mg2+, Cu2+, Ag+, Fe2+, and Ca2+) on the NPOC
15
analysis by the proposed method were carefully investigated. As summarized in Table
16
S2, no significant interferences from the tested cations are evident, even at
17
concomitant concentrations as high as 500 mg L-1. Moreover, the results also
18
demonstrate that the interferences from 100.0 g L-1 of PO43- and SO42- are not present.
19
However, 100.0 g L-1 of NO3- and Cl- induced serious interference on the NPOC
20
analysis and the recoveries decreased to 73% and 65%, respectively. To further
21
explore the effects of NO3- and Cl-, different concentrations of NO3- and Cl- were
22
added to standard solutions containing 10.0 mg L-1 KHP (as C) and analyzed by the
23
proposed methods. As can be seen in Figure S7, recoveries were enhanced above 80%
24
when the concentration of NO3- and Cl- were lower than 10 g L-1, which is sufficient
25
for the routine analysis of NPOC in typical surface water samples.
26
Analytical Performance. Under optimal condition, a series of NPOC standard
27
solutions in the range of 0.5-5000 mg L-1 were analyzed by the HE-POVG-PD-OES.
28
Results are summarized in Figure 5a,which show that linear range can be extended to
29
200 mg L-1 and is limited by saturation of the CCD spectrometer. Thus, the calibration
30
curve was finally constructed by analyzing a series of standard solutions with the 11
ACS Paragon Plus Environment
Environmental Science & Technology
1
NPOC ranging from 0.5-200 mg L-1 (based on 0.5 mL sample volume), as shown in
2
Figure 5b. The linear correlation coefficient (R2) for the constructed calibration curve
3
is better than 0.999. The limits of detection (LOD), defined as the analyte
4
concentration equivalent to three times the standard deviation of 11 measurements of
5
a blank solution (UP water) divided by the slope of the calibration curve, was 0.05 mg
6
L-1. Figure S8 illustrates steady-state signals obtained for the 11 replicate
7
measurements of a 5 mg L-1 NPOC standard solution using the proposed system,
8
yielding a precision of 5.0% relative standard deviation (RSD). Table S3 summarizes
9
the analytical performance of this method and compares it with some other methods.
10
The results indicate that the analytical performance of the proposed system is
11
comparable to or better than that obtained by other techniques. It is noteworthy that
12
although the sample consumption of the proposed system is reduced some 20-fold
13
compared to the MOVG-DBD-OES (10 mL of sample volume), the obtained LOD
14
remains comparable to that achieved by MOVG-DBD-OES, and the LOD is improved
15
20-fold when the HE-POVG reactor was used as an alternative to the conventional
16
photo-oxidation reactor. These may be a consequence of the high photo-oxidation
17
vapor generation efficiency of the proposed reactor coupled with the high excitation
18
capability of the PD microplasma. Moreover, this system can further provide several
19
unique advantages for online, continuous monitoring as it comprises an inexpensive
20
and miniature setup, requires low power consumption, reduces use of toxic chemicals
21
and achieves a high sample throughput (1.5 min per sample).
22
Sample Analysis with FI-HE-POVG-PD-OES. The utility and accuracy of the
23
FI-HE-POVG-PD-OES system were validated by the determination of NPOC in real
24
water samples. The lake water samples were simultaneously analyzed by the proposed
25
system and by use of a commercial HTC-NDIR. Results are summarized in Table 1.
26
The t test shows that there are no significant differences between the analytical results
27
obtained by the proposed method and the HTC-NDIR at the 95% level of confidence.
28
Secondly, the river water samples were also used to validate the accuracy of the
29
proposed system via evaluation of the recoveries of the spiked NPOC. As can be seen
30
from the data in Table 2, recoveries calculated from spiking standards into the real 12
ACS Paragon Plus Environment
Page 12 of 28
Page 13 of 28
Environmental Science & Technology
1
samples were in range of 91−111%, further confirming the accuracy and practicality
2
of the proposed system for NPOC analysis.
3
Online, Continuous Monitoring of NPOC in Water System. The aim of this work
4
was to develop a simple, inexpensive, online and continuous system for the
5
continuous monitoring of NPOC. Therefore, the feasibility of online inorganic carbon
6
removal was firstly investigated by using a river water sample. The sample was
7
separately analyzed both without any pretreatment and after an offline or online
8
acidification using 10% (v/v) phosphoric acid and Ar purge. As can be seen from
9
Figure 6a, the response obtained with online acidification and purge is almost the
10
same as that obtained with the offline mode, indicating that inorganic carbon can be
11
efficiently removed with the online acidification and purge and its interference can be
12
online eliminated. Moreover, TIC can also be monitored online with this system via
13
the detection of the CO2 generated from the acidification and purging of the sample,
14
as shown in Figure 6a. The potential of online and continuous monitoring of NPOC
15
by the proposed system was further evaluated by continuously monitoring the NPOC
16
variation of a water sample flow, as shown in Figure 6b. In order to increase the
17
NPOC value of the sample, KHP solution was gradually added to the sample flow.
18
The results show that the signals quickly responded when the NPOC of sample flow
19
changed. A calibration curve with linear coefficient of 0.999 could be obtained based
20
on responses accorded by peak height, as shown in Figure S9. Moreover, the response
21
rapidly dropped to the blank value as 18 MΩ cm DIW was introduced, showing no
22
memory effect occurred in this system. These suggest that our developed system can
23
accomplish online and continuous monitoring of NPOC.
24
The practicality of long-term monitoring of real water was evaluated by continuous
25
monitoring the NPOC of tap water (Figure S10). Figure 6c shows the results obtained
26
after uninterrupted monitoring for more than 12 hours. After monitoring for 5.5 hours,
27
a sharp response change is detected. This is because a solution containing a high
28
concentration of glucose was gradually introduced into the flow of tap water, showing
29
the rapid response of this system. These results strongly confirm the practicality of the
30
HE-POVG-PD-OES for continuous and online monitoring of NPOC in real water. 13
ACS Paragon Plus Environment
Environmental Science & Technology
1
In summary, a promising NPOC monitoring analyzer was developed for NPOC
2
analysis by coupling a specially designed photo-oxidation vapor generator and
3
miniaturized PD microplasma OES. Bestowed to the advantages of high oxidation
4
efficiencies of organics and continuous operation provided by the generator and high
5
excitation capability, inexpensive and simple setup, low power consumption offered
6
by the PD-OES, this system can be used to accomplish online, continuously and
7
inexpensive monitoring NPOC of real water. This will be very helpful to developing
8
countries, allowing the convenient determination and online control of water qualit.
9 10
ACKNOWLEDGEMENTS
11
We gratefully acknowledge the National Nature Science Foundation of China (Grant
12
Nos. 21575092 and 21622508) for financial support.
13
ASSOCIATED CONTENT
14
Supporting Information. Additional information as noted in text. This material is
15
available free of charge via the Internet at http://pubs.acs.org.
16
14
ACS Paragon Plus Environment
Page 14 of 28
Page 15 of 28
Environmental Science & Technology
1
Reference
2
(1) Eliasson, J. The rising pressure of global water shortages. Nature 2015, 517, 6.
3
(2) Nazareno, A. G.; Laurance, W. F. Brazil's drought: Beware deforestation. Science 2015, 347, 1427-1428.
4 5
(3) Qiu, J. China drought highlights future climate threats. Nature 2010, 465, 142-143.
6 7
(4) Tong, T. Z.; Elimelech, M. The global rise of zero liquid discharge for wastewater
8
management: drivers, technologies, and future directions. Environ. Sci. Technol.
9
2016, 50, 6846–6855.
10
(5) Alsbaiee, A.; Smith, B. J.; Xiao, L. L.; Ling, Y. H.; Helbling, D. E.; Dichtel, W. R.
11
Rapid removal of organic micropollutants from water by a porous β-cyclodextrin
12
polymer. Nature 2016, 529, 190–194.
13
(6) Namour, Ph.; Jaffrezic-Renault, N. Sensors for measuring biodegradable and total organic matter. TRAC-Trend. Anal. Chem. 2010, 29, 848-857.
14 15
(7) Pang, H. L.; Kwok, H. Y.; Chan, P. H.; Yeung, C. H.; Lo, W.; Wong, K. Y.
16
High-throughput determination of biochemical oxygen demand (BOD) by a
17
microplate-based biosensor. Environ. Sci. Technol. 2007, 41, 4038-4044.
18
(8) Dharmadhikari, D. M.; Vanerkar, A. P.; Barhate, N. M. Chemical oxygen demand
19
using closed microwave digestion system. Environ. Sci. Technol. 2005, 39,
20
6198-6201.
21
(9) Yu, H. B.; Ma, C. J.; Quan, X.; Chen, S.; Zhao, H. M. Flow injection analysis of
22
chemical oxygen demand (COD) by using a boron-doped diamond (BDD)
23
electrode. Environ. Sci. Technol. 2009, 43, 1935-1939.
24
(10) Gutiérrez-Capitán, M.; Baldi, A.; Gómez, R.; García, V.; Jiménez-Jorquera, C.;
25
Fernández-Sánchez, C. Electrochemical nanocomposite-derived sensor for the
26
analysis of chemical oxygen demand in urban wastewaters. Anal. Chem. 2015, 87,
27
2152–2160.
28
(11) Zheng, Q.; Zhou, B.; Bai, J.; Li, L.; Jin, Z.; Zhang, J.; Li, J.; Liu, Y.; Cai, W.;
29
Zhu, X. Self-organized TiO2 nanotube array sensor for the determination of 15
ACS Paragon Plus Environment
Environmental Science & Technology
chemical oxygen demand. Adv. Mater. 2008, 20, 1044-1049.
1 2
(12) Kim, Y. C.; Sasaki, S.; Yano, K.; Ikebukuro, K.; Hashimoto, K.; Karube, I.
3
Photocatalytic sensor for the determination of chemical oxygen demand using
4
flow injection analysis. Ana. Chim. Acta 2001, 432, 59-66.
5
(13) Su, Y. Y.; Li, X. H.; Chen, H.; Lv, Y.; Hou, X. D. Rapid, sensitive and on-line
6
measurement of chemical oxygen demand by novel optical method based on UV
7
photolysis and chemiluminescence. Microchem. J. 2007, 87, 56-61.
8
(14) Dan, D. Z.; Sandford, R. C.; Worsfold, P. J. Determination of chemical oxygen
9
demand in fresh waters using flow injection with on-line UV-photocatalytic oxidation and spectrophotometric detection. Analyst 2005, 130, 227-32.
10 11
(15) Zhao, H. J.; Jiang, D. L.; Zhang, S. Q.; Catterall, K.; John, R. Development of a
12
direct photoelectrochemical method for determination of chemical oxygen
13
demand. Anal. Chem. 2004, 76, 155-160.
14
(16) Yuan, S. J.; Mao, R.Y.;; Li. Y. G.; Zhang, Q. D.; Wang, H. Z. Layer-by-layer
15
assembling TiO2 film from anatase TiO2 sols as the photoelectrochemical sensor
16
for the determination of chemical oxygen demand. Electrochim. Acta 2012, 60,
17
347-353.
18
(17) Zhang, S. Q.; Jiang, D. L.; Zhao, H. J. Development of chemical oxygen
19
demand on-line monitoring system based on a photoelectrochemical degradation
20
principle. Environ. Sci. Technol. 2006, 40, 2363-2368.
21
(18) Zhang, S. Q.; Li, L. H.; Zhao, H. J. A portable photoelectrochemical probe for
22
rapid determination of chemical oxygen demand in wastewaters. Environ. Sci.
23
Technol. 2009, 43, 7810-7815.
24
(19) Fang, J. Y.; Shang, C. Bromate formation from bromide oxidation by the UV/persulfate process. Environ. Sci. Technol. 2012, 46, 8976-83.
25 26
(20) Armstrong, F. A. J.; Williams, P. M.; Strickland, J. D. H. Photo-oxidation of
27
Organic Matter in Sea Water by Ultra-violet Radiation, Analytical and Other
28
Applications. Nature 1966, 211, 481−483.
29
(21) Federer, U.; Kaufmann, P. R; Hutterli, M. A; Schupbach, S.; Stocker, T. F.
30
Continuous flow analysis of total organic carbon in polar ice cores. Environ. Sci. 16
ACS Paragon Plus Environment
Page 16 of 28
Page 17 of 28
Environmental Science & Technology
Technol. 2008, 42, 8039-43.
1 2
(22) Bisutti, I.; Hilke, I.; Raessler, M. Determination of total organic carbon - an overview of current methods. TRAC-Trend. Anal. Chem. 2004, 23, 716-726.
3 4
(23) Panetta, R. J; Ibrahim, M.; Gelinas, Y. Coupling a high-temperature catalytic
5
oxidation total organic carbon analyzer to an isotope ratio mass spectrometer to
6
measure natural-abundance delta13C-dissolved organic carbon in marine and
7
freshwater samples. Anal. Chem. 2008, 80, 5232-9.
8
(24) Qian, J. G.; Mopper, K. Automated high-performance, high-temperature combustion total organic carbon analyzer. Anal. Chem. 1996, 68, 3090–3097.
9 10
(25) Martin, P. E.; Barker, E. F. The infrared absorption spectrum of carbon dioxide. Phys. Rev. 1932, 41, 291.
11 12
(26) Kieselbach, R. Continuous recording of concentration of organic matter in waste water. Anal. Chem. 1954, 26, 1312−1318.
13 14
(27) Stroble, S. T.; Kounaves, S.P. An electrochemically based total organic carbon
15
analyzer for planetary and terrestrial on-site applications. Anal. Chem. 2012, 84,
16
6271-6276.
17
(28) Seligson, D.; Seligson, H. Microdetermination of carbon dioxide liberated by acidification or oxidation. Anal. Chem. 1951, 23, 1877−1878.
18 19
(29) Fung, Y. S.; Wu, Z. C.; Dao, K. L. Determination of Total Organic Carbon in
20
Water by Thermal Combustion-Ion Chromatography. Anal. Chem. 1996, 68,
21
2186−2190.
22
(30) Han, B. J.; Jiang, X. M.; Hou, X. D.; Zheng, C. B. Miniaturized dielectric
23
barrier
discharge
carbon
atomic
emission
spectrometry
with
online
24
microwave-assisted oxidation for determination of total organic carbon. Anal.
25
Chem. 2014, 86, 6214-6219.
26
(31) Nakazato, T.; Tao, H. A high-efficiency photo-oxidation reactor for speciation of
27
organic arsenicals by liquid chromatography - hydride generation - ICPMS. Anal.
28
Chem. 2006, 78, 1665-1672.
29
(32) Zhang, S.; Luo, H.; Peng, M. T.; Tian, Y. F.; Hou, X. D.; Jiang, X. M.; Zheng, C.
30
B. Determination of Hg, Fe, Ni, and Co by miniaturized optical emission 17
ACS Paragon Plus Environment
Environmental Science & Technology
1
spectrometry integrated with flow injection photochemical vapor generation and
2
point discharge. Anal. Chem. 2015, 87, 10712-10718.
3
(33) Rao, Y. F.; Chu, W. Reaction mechanism of linuron degradation in TiO2
4
suspension under visible light irradiation with the assistance of H2O2. Environ. Sci.
5
Technol. 2009, 43, 6183–6189.
6
(34) Asahi, R.; Morikawa, T.; Irie, H.; Ohwaki. T. Nitrogen-doped titanium dioxide
7
as visible-light-sensitive photocatalyst: designs, developments, and prospects.
8
Chem. Rev. 2014, 114, 9824–9852.
9
(35) Zhang, Y. Q.; Du, X. Z.; Huang, W. L. Temperature effect on the kinetics of persulfate oxidation of p-chloroaniline. Chin. Chem. Lett. 2011, 22, 358-361.
10 11
(36) Leng, A. Q.; Lin, Y.; Tian, Y. F.; Wu, L.; Jiang, X. M. Hou, X. D.; Zheng, C. B.
12
Pump- and valve-free flow injection capillary liquid electrode discharge optical
13
emission spectrometry coupled to a droplet array platform. Anal. Chem. 2017, 89,
14
703–710.
15
(37) Pickhardt, W. P.; Oemler, A. N.; Mitchell, J. Determination of total carbon in
16
organic materials by wet-dry combustion method. Anal. Chem. 1955, 27,
17
1784−1788.
18
(38) Maestre, S. E.; Mora, J.; Hernandis, V.; Todolí, J. L. A system for the direct
19
determination of the nonvolatile organic carbon, dissolved organic carbon, and
20
inorganic carbon in water samples through inductively coupled plasma atomic
21
emission spectrometry. Anal. Chem. 2003, 75, 111−117.
22
18
ACS Paragon Plus Environment
Page 18 of 28
Page 19 of 28
Environmental Science & Technology
1
Figure Captions
2
Figure 1. Schematic diagram of the FI-HE-POVG-PD-OES. GLS: gas liquid
3
separator.
4
Figure 2. (a) Optical emission spectrum obtained under different conditions; (b)
5
Comparison of the responses of carbon atomic emission at 193.0 nm using
6
HE-POVG-PD-OES and conventional POVG-PD-OES; and (c) Calibration curves
7
established using FI-HE-POVG-PD-OES. Experimental conditions: discharge voltage,
8
2.55 kV; discharge gap, 3 mm; Ar flow rate, 300 mL min-1; carrier solution flow rate,
9
3 mL min-1; the concentration of Na2S2O8 solution, 300 g L-1, and CCD integration
10
time, 100 ms.
11
Figure 3. (a) Oxidation efficiencies of different organic compounds relative to KHP
12
NPOC standard; and (b) Calibration curves established by analyzing sample
13
containing different organics. Experimental conditions: discharge voltage, 2.55 kV;
14
discharge gap, 3 mm; Ar flow rate, 300 mL min-1; carrier solution flow rate, 3 mL
15
min-1; and the concentration of Na2S2O8 solution, 300 g L-1.
16
Figure 4. Effect of acidification and purging on NPOC analysis.
17
Figure 5. (a) Plots of carbon atomic emission intensity as a function of NPOC
18
concentration from 0.5 to 5000 mg L−1, showing good linearity in the range 0.5 to 200
19
mg L−1; and (b) Typical calibration curve using FI-HE-POVG-PD-OES. Experimental
20
conditions: discharge voltage, 2.55 kV; discharge gap, 3 mm; Ar flow rate, 300 mL
21
min-1; carrier solution flow rate, 3 mL min-1; and the concentration of Na2S2O8
22
solution, 300 g L-1.
23
Figure 6. (a) Comparison of the removal of inorganic carbon using online and offline
24
acidification and purging; (b) Feasibility of analysis of NPOC by continuous
25
HE-POVG-PD-OES; and (c) Continuous monitoring of NPOC in tap water using the
26
proposed system. Experimental conditions: discharge voltage, 2.55 kV; discharge gap,
27
3 mm; Ar flow rate, 300 mL min-1; carrier solution flow rate, 3 mL min-1; the
28
concentration of Na2S2O8 solution, 300 g L-1; and the concentration of phosphoric
29
acid, 10% (v/v).
30 19
ACS Paragon Plus Environment
Environmental Science & Technology
1
2 3
Figure 1.
4
20
ACS Paragon Plus Environment
Page 20 of 28
Page 21 of 28
Environmental Science & Technology
1
2 3 4
Figure 2.
5
21
ACS Paragon Plus Environment
Environmental Science & Technology
1
2 3 4
Figure 3.
5
22
ACS Paragon Plus Environment
Page 22 of 28
Page 23 of 28
Environmental Science & Technology
1 2 3
Figure 4.
4
23
ACS Paragon Plus Environment
Environmental Science & Technology
1
2 3
Figure 5.
24
ACS Paragon Plus Environment
Page 24 of 28
Page 25 of 28
Environmental Science & Technology
1 2
Figure 6.
3
25
ACS Paragon Plus Environment
Environmental Science & Technology
Page 26 of 28
1
Table 1. Sample Detection Sample
Sampling location
UV-PVG-PD-OES -1 a
HTC-NDIR
(mg L )
(mg L-1)
1
Southwest Jiaotong University
7.03 ± 0.50
7.12 ± 0.06
2
Huanhuaxi Park-1
4.81 ± 0.22
5.22 ± 0.28
3
Huanhuaxi Park-2
1.92 ± 0.15
2.03 ± 0.21
4
Chenghua Park
1.97 ± 0.08
2.25 ± 0.20
5
Xinhua Park
5.24 ± 0.59
5.52 ± 0.43
6
Renmin Park
5.26 ± 0.25
5.41 ± 0.08
7
Wangjiang Park
1.37 ± 0.16
1.52 ± 0.03
8
Donghu Park
5.51 ± 0.48
5.81 ± 0.09
9
Tazishan Park
7.98 ± 0.20
8.15 ± 0.16
10
Mingyuan Lake
5.32 ± 0.34
5.56 ± 0.18
a
Average ± standard deviation of three trials.
2 3 4
26
ACS Paragon Plus Environment
Page 27 of 28
Environmental Science & Technology
1
Table 2. Sample Detection Samples
Added, mg L-1
Found, mg L-1a
Recovery, %
Drinking water
0.00
0.83 ± 0.13
-
2.00
2.88 ± 0.07
103
5.00
6.31 ± 0.37
110
0.00
6.37 ± 0.72
-
5.00
11.93 ± 0.77
111
0.00
4.53 ± 0.06
-
5.00
9.10 ± 0.53
91
0.00
5.30 ± 0.26
-
5.00
10.03 ± 0.95
95
0.00
12.40 ± 0.36
-
5.00
17.70 ± 0.46
106
10.00
22.30 ± 0.95
99
Fu river
Nan river
Funan river-1
Funan river-2
a
Average ± standard deviation of three trials.
2 3
27
ACS Paragon Plus Environment
Environmental Science & Technology
For TOC only
1
2 3
28
ACS Paragon Plus Environment
Page 28 of 28