High-Sensitivity Detection of Iron(III) by Dopamine ... - ACS Publications

Jun 11, 2018 - concentration FeCl3 solutions and quantitative DOPA was carried out. ..... the membrane was washed three times and reserved for backup...
0 downloads 0 Views 2MB Size
Subscriber access provided by UNIV OF SOUTHERN QUEENSLAND

Functional Nanostructured Materials (including low-D carbon)

High-Sensitive Detection of Iron (III) by Dopamine-Modified Funnel-Shaped Nanochannel Bo Niu, Kai Xiao, Xiaodong Huang, Zhen Zhang, Xiang-Yu Kong, Ziqi Wang, Liping Wen, and Lei Jiang ACS Appl. Mater. Interfaces, Just Accepted Manuscript • DOI: 10.1021/acsami.8b05686 • Publication Date (Web): 11 Jun 2018 Downloaded from http://pubs.acs.org on June 11, 2018

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 27 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

1

High-Sensitive Detection of Iron (III) by

2

Dopamine-Modified Funnel-Shaped Nanochannel

3

Bo Niu1,2,†, Kai Xiao1,†, Xiaodong Huang1, Zhen Zhang1, Xiang-Yu Kong1,*, Ziqi Wang1,

4

Liping Wen1,2,* and Lei Jiang1,2

5

1

6

and Chemistry, Chinese Academy of Sciences, Beijing 100190, P. R. China.

7

2

8

R. China

9

*

Key Laboratory of Bio-inspired Materials and Interfacial Science, Technical Institute of Physics

School of Future Technology, University of Chinese Academy of Sciences, Beijing 100049, P.

Corresponding Author

10

E-mail: [email protected]; [email protected]

11



12

Keywords: funnel-shaped nanochannels, dopamine, FeIII sensor, EDTA-2Na, switchability

These authors contributed equally to this work.

13 14 15 16 17 18

ACS Paragon Plus Environment

1

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

19

Page 2 of 27

Abstract

20

Iron as an essential trace element in human body participates in various biological processes.

21

The demand for efficient and sensitive detection of FeIII has drawn wide attentions. Inspired by

22

biological nanochannels, a high-sensitive, economic and recyclable FeIII detection method is

23

proposed by using dopamine-modified funnel-shaped nanochannels. Along with the FeIII

24

concentration changing, different FeIII-dopamine (FeIII-DOPA) chelates are generated in the

25

channel, which affect the wettability and charge distribution of the pore surface, resulting in the

26

changing of ionic current through the nanochannels. Meanwhile, the funnel-shaped nanochannel

27

applied in this work with a narrow cylindrical segment (diameter close to 10 nm) as the critical

28

section can enhance the sensing ability to ultra-trance level (down to 10-12 M). We expound the

29

mechanism and feasibility of this method, and anticipate the system can be a good example to

30

design highly sensitive and stable ion detection devices.

31 32 33 34 35 36 37 38 39 40

ACS Paragon Plus Environment

2

Page 3 of 27 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

41

ACS Applied Materials & Interfaces

Introduction

42

FeIII is a biological important metal ion and plays essential roles in synthesizing a series of

43

enzymes involved in oxygen uptake, oxygen metabolism, and electron transfer.1-2 Imbalanced

44

FeIII levels affect the normal activities in living organisms severely.3-5 For example, excessive

45

FeIII in human body is poisonous, and only when the high valence FeIII uptake from the drinking

46

water and food is converted to low valence states FeII, can it be absorbed by intestinal tract. Once

47

the FeIII is over intaken, the insolubility of FeIII and the formation of toxic radicals, especially the

48

hydroxyl radical, will cause severe disease. Therefore, regular circulation of FeIII has become an

49

important indicator of human health status, which makes it particularly necessary to demonstrate

50

the further research of FeIII detection technology.6 Currently, some methods involved in the

51

detection of FeIII have been implemented by designing fluorescent probes7-9, functionalizing

52

doped carbon nanomaterials10-12 and graphene quantum dots13-15 and synthesising of metal-

53

organic-frameworks16-18, etc. Those methods have realized the sensitive detection of FeIII, and

54

some of them exhibited specific recognition. However, these technologies are always costly or

55

have limited detection limits, which restrict their further applications. Recently, we and other

56

groups reported that functionalized nanochannels could be used as a new platform to realize

57

various ions detection.19-22 Despite the simply structure, the sensing devices based on the

58

biomimetic nanochannels have achieved the highly specific recognition and ultrasensitive

59

detection.23-25 The fabricated nanochannels exhibit excellent characteristics such as controlled

60

shape and pore size, good stability, and ease of incorporation with other devices.26-27 These

61

excellent properties make bionic nanochannels be a potential substitute for biological channels.

62

To date, the main research focused on the design of the different shapes and the modification of

63

functional molecules in the nanochannels. In detail, various solid-state nanochannels with

ACS Paragon Plus Environment

3

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 4 of 27

64

different morphology including symmetrical shapes, such as cylindrical,28 hourglass-shaped,29

65

cigar-shaped30 nanochannels and asymmetric shapes, such as conical,31 bullet-shaped32 and

66

funnel-shaped33 nanochannels have received extensive attention. Among all the different shapes

67

of nanochannels, the funnel-shaped nanochannel which possess a straight cylindrical segment as

68

the critical section, has dramatically improved the controllability and the stability in ion

69

transport.33 Based on this, a series of experiments to verify the special characteristics of funnel-

70

shaped nanochannel has been carried out recently.34-35

71

In this work, we report the dopamine-modified funnel-shaped nanochannels that can realize

72

recyclable ultra-trace FeIII ions detection. As shown in Figure 1a, the DOPA modification can be

73

accomplished by one step coupling reaction between the amino in DOPA and the carboxyl

74

groups in the inner surface of the channel, which could be confirmed by X-ray photoelectron

75

spectrum and contact angle measurement (Figure S1&S2, supporting information). Then,

76

different FeIII-DOPA chelates were generated along with the ratio of DOPA and FeIII.36 At last,

77

by adding disodium ethylenediaminetetra-acetate (EDTA-2Na), the FeIII-DOPA chelates were

78

destroyed and FeIII was removed from the channel because the binding capacity of FeIII to

79

EDTA-2Na was stronger than that of FeIII with DOPA (Figure 1 iv, v).37 Based on this, such a

80

system can clearly realize the recyclable FeIII ions detection. This particular funnel-shaped

81

nanochannel used in this work was shown in Figure 1b, which had two different segments: the

82

conical section with ~7.5 µm length and the cylindrical section with ~4.5 µm length. The

83

lengthened straight critical section with diameter of ~10 nm was benefit to improve the

84

sensitivity of ion identification.

ACS Paragon Plus Environment

4

Page 5 of 27 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

85 86

Figure 1. (a) The schematic description of the FeIII activated ionic nanochannel and the inner

87

surface of the funnel-shaped nanochannels at different states: the unmodified state after etching

88

(i); DOPA modified (ii); cross-linked chelate after FeIII response with excess DOPA (iii); cross-

89

linked chelate after equal FeIII response with DOPA (iv); and the EDTA-2Na treatment (v). (b)

90

The cross-section SEM images of a single funnel-shaped PET nanochannel with conical segment

91

and cylindrical section.

92

Results and Discussion

93

The current-voltage (I-V) as a current value measurement is extensively applied in verifying

94

the properties of the fabricated nanochannel including the charge distribution and wettability of

95

the inner surface, even calculating the channel (pore) radius.38-39 As shown in Figure 2, the I-V

96

curves provide direct signals to demonstrate the successful modification of DOPA. In particular,

97

each step of reaction was monitored by measuring I-V in 0.1 M KCl. The DOPA modified

ACS Paragon Plus Environment

5

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 6 of 27

98

funnel-shaped nanochannel showed different behaviours under different pH. As shown in Figure

99

2a, when the pH value was 3, the unmodified nanochannel showed symmetric ion transportation

100

properties. The ion current value (absolute value) at ± 2V was almost the same (2.4 nA at 2 V; -

101

2.5 nA at -2 V), which indicated there was no rectification (the rectification was defined as the

102

ratio of absolute current at given negative voltage and the current value at corresponding positive

103

voltage). After the nanochannels were modified with DOPA, the current at positive voltage

104

increased intensively, and the rectification occurred, which were attributed to the protonation of

105

the hydroxyl groups. The I-V curves decreased to the unmodified level after immersing the

106

DOPA-modified nanochannels in 20 mM FeCl3 solution for 2 h. This phenomenon was

107

contributed to the less surface charge, which was caused by the FeIII locating in the centre of the

108

chelates and the hydrophilic hydroxyl group decreased remarkably during the reaction. In

109

addition, the contact angle measurement showed a more hydrophobic surface after adding FeIII,

110

which confirmed the chelating process. (more information see Figure S2). As shown in Figure

111

2b, under pH 7, the DOPA modified nanochannel showed negative surface charges due to the

112

carboxyl formed in the etching process. After the responded to FeIII, the ion currents decreased

113

further, to about -8.2 nA under -2 V and about 3.4 nA under +2 V. For the different states:

114

unmodified, DOPA modified and DOPA-FeIII modified, the corresponding ion current values at -

115

2 V were -45.2 nA, -22.3 nA and -8.4 nA, respectively. The values showed a decreasing trend,

116

which was mainly due to the reduction of the surface negative charge and the decrease of

117

wettability.

ACS Paragon Plus Environment

6

Page 7 of 27 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

118 119

Figure 2. (a) The I-V curves of the nanochannels before (black), after (navy) DOPA

120

modification and FeIII response (dark cyan) in pH 3, 0.1 mol L-1 KCl solution and the scheme of

121

DOPA modified funnel-shaped single nanochannel under pH 3. (b) The I-V curves of the

122

nanochannels before (black), after (navy) DOPA modification and FeIII response (dark cyan) in

123

0.1 mol L-1 of KCl solution pH 7 and the scheme of DOPA modified funnel-shaped single

124

nanochannel under pH 7.

125

As shown in Figure 2, the I-V curves of dopamine modified nanochannel had a response of pH.

126

At pH 3 and 7, the nanochannel showed opposite rectification, which indicated the charge in the

127

nanochannel realized a reversion from positive to negative. Based on the reversion of the charge,

128

there would be an “isoelectric” point between pH 3&7. Therefore, we carried out the experiment

129

of different pH to find out the “isoelectric” point. As shown in Table 1, we chose 7 points of

ACS Paragon Plus Environment

7

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 8 of 27

130

different pH values from 2.60 to 5.63. The rectification ratios calculated by I+2V/I-2V showed

131

remarkable decrease as the pH increased from 2.60 to 4.99. It was worth mentioning that the

132

rectification ratio decreased to 1.00 when the pH values were close to 4.99. As the pH continued

133

to increase to 5.63, the rectification ratio (calculated by |I+2V/I-2V|) gradually increased from 1.05

134

to 3.56. In order to clearly describe the “isoelectric” point, the I-V curves and the distribution of

135

rectification ratios along with the pH were presented in Figure 3. As shown in Figure 3a, the I-V

136

curves of the DOPA-modified nanochannel at pH 2.60, 4.99 and 5.63 exhibited three different

137

curves. When the pH was 2.60, the nanochannel was positively charged, thus, the I-V curve

138

showed promoted ion current at positive voltage. While the pH was increased to 5.63, the

139

nanochannel was negatively charged and the I-V curve showed restricted ion current at positive

140

voltage. More noteworthy, the I-V curve in Figure 3a was a “symmetrical line” at positive and

141

negative voltage when the pH was 4.99 (dark cyan). As described above, the “isoelectric” point

142

meant the charge in the nanochannel was balanced, thus, the rectification ratio was closed to 1.

143

As shown in Figure 3b, When the pH was at 4.85 and 4.99, the rectification ratio fell on the line

144

of x = ± 1. (The algorithm |I-2V/I+2V| and I+2V/I-2V made the points fall around the edge of the

145

light blue area of Rec = ± 1) The zwitterionic nature of dopamine led to the rectification reversal

146

below and above the isoelectric point (pH=4.9).

147

Table 1. The ion current values at ± 2V under different pH conditions and the rectification ratios

148

calculated by| |I-2V/I+2V| (I+2V/I-2V).

pH I-2V /A× ×10-8 I+2V/A× ×10-8 R(I+2V/I-2V) R(| |I-2V/I+2V|)

2.60 -3.95 57.86 -14.66 /

3.62 -3.02 29.54 -9.78 /

4.63 -6.10 12.00 -1.97 /

4.85 -10.54 10.96 -0.96 1.04

4.99 -4.15 4.38 -0.95 1.05

5.23 -3.94 2.49 / 1.58

5.63 -14.65 4.12 / 3.56

149

ACS Paragon Plus Environment

8

Page 9 of 27 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

150 151

Figure 3. (a) The I-V curves of the DOPA-modified nanochannel under different pH values (3.62,

152

4.99 and 5.63). (b) Rectification ratio (Rec) as a function of pH.

153

To clearly figure out the detailed mechanism of the reaction between the DOPA and FeIII, the

154

experiment between different concentration FeCl3 solutions and quantitative DOPA was carried

155

out. In general, metal complexes, especially the chelates, show characteristic intense colours and

156

the colour changes with different metal concentrations.40-41As shown in Figure 4, the specific

157

FeIII responding process was characterized through the colour change in solution. At first, the

158

DOPA dissolved in water was colourless. With the continuous addition of FeCl3, the colour of

159

the solution gradually deepened to dark green. After adding EDTA-2Na, the dark green solution

160

turned back to colourless again. The colour changes were caused by the complicated reaction

161

between DOPA and FeIII. In detail, one FeIII may bind more than one DOPA molecule. The

162

bonding reaction happens between the two functional groups (phenolic hydroxyl) and FeIII

163

(Figure S3). When the FeIII was added into the DOPA overdosed solution, a cross-linked

164

complex [Fe(DOPA)3] with FeIII : DOPA= 3 : 1 was formed, along with the continuously adding

ACS Paragon Plus Environment

9

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 10 of 27

165

FeCl3 ,the complex Fe(DOPA) with FeIII : DOPA= 1 : 1 was formed.36,42 The different structures

166

of the chelates exhibited different colours in the solution.43

167

Figure 4. Schematic illustration of colour change of the DOPA solution mixed in different

168

concentration of FeIII, from which we can obtain the probably products of the different ratio of

169

DOPA and FeIII. Moreover, the addition of EDTA-2Na removing the color in the vials directly

170

demonstrates that the bond force of EDTA-2Na with FeIII is stronger than that of DOPA with

171

FeIII.

172

Meanwhile, UV-vis absorption spectra of different ratio of FeIII and DOPA in solvent were

173

collected. As expected, the UV-vis absorption spectra of DOPA and FeIII at different ratios

174

provided detailed mechanism of FeIII reacting with DOPA (Figure 5). DOPA solution (20 mM)

175

exhibited one broad absorption band ranging from 250 to 320 nm with a maximum located at

176

λmax=280 nm, which resulted from the two phenolic hydroxyl.44 Then, the UV-vis absorption

ACS Paragon Plus Environment

10

Page 11 of 27 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

177

intensity of DOPA was enhanced gradually with increasing FeIII concentrations. In particular, the

178

absorption peak of the hydroxyl group could be measured when no FeIII was added or the ratio of

179

DOPA to FeIII was less than 1:2. With the increasing of FeIII ions, the amount of functional group

180

(phenolic hydroxyl) decreased significantly, thus, the characteristic absorption peak gradually

181

disappeared. (the light blue section overlaid between the λ=260 & 305 nm clearly showed the

182

change of the absorption peak)

183

Figure 5. The UV-vis absorption spectrum (λ=200 nm~500 nm) by fresh 20 mM DOPA (keep

184

away from light, 0.1 M Tris-HCl buffer) and FeCl3 solution at different ratio.

185

As mentioned above, different chelates can be formed with altering ratio between DOPA and

186

FeIII. As shown in Figure 6a, the DOPA-modified nanochannels can even response to FeIII ions at

187

the ultralow concentration (0.01 nM), which proved that the DOPA-modified nanochannel was

188

extremely sensitive to FeIII ions. The I-V curves of full FeIII concentration from 0.001 nM to 100

189

nM can be seen in the Figure S4. The ion current increased from -163.3 nA to -46.4 nA gradually

190

along with the increase of FeIII concentration. When the concentration of FeIII reached to 1 nM,

ACS Paragon Plus Environment

11

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 12 of 27

191

the ionic current possessed a maximum value of -46.4 nA at -2 V. The trend of the ion current

192

was indicated on the side of the I-V curves in Figure 6a. With the further increase of FeIII

193

concentration, the ionic current had a tendency to decrease from -46.4 nA to -143.2 nA at -2 V

194

and increase from 11.4 nA to 23.7 nA at +2 V (Figure 6a, b). A schematic presentation for this

195

phenomenon was shown in Figure 6c (i, ii, iii, iv). The three schemes in Figure 6c (ii, iii and iv)

196

correspond to the three vertices in Figure 6b, respectively. As shown on the simulated nanopore

197

surface, the charge distribution and the wettability of the nanochannels have a significate impact

198

on the ion transport. Figure 6c (i) showed the state of the DOPA modified nanochannels. When

199

the FeIII concentrations was low (10-3 nM), the nanochannel was partially negative charged

200

because not all hydroxyl can combine with FeIII ions (Figure 6c ii). Along with the increasing of

201

FeIII concentration to 1 nM, the chelates can be formed between three DOPA molecules and one

202

FeIII ion. Under this condition, the nanochannel was electronic neutral and low hydrophilicity

203

(Figure 6c iii). With the further increase of FeIII to 100 nM, the complex DOPA-FeIII chelates

204

can be formed between one DOPA molecular and one FeIII ion. Under this condition, the pore

205

surface was negatively charged due to the free negative hydroxyl bonding to FeIII.45 The change

206

of the surface charge density and the wettability were the essential reason for the changing of

207

current values.

ACS Paragon Plus Environment

12

Page 13 of 27 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

208 209

Figure 6. FeIII response to DOPA-modified funnel-shaped nanochannels. (a)The I-V curves of

210

the DOPA-modified nanochannel with increasing FeIII concentration. (b) With the increasing

211

FeIII concentration, the change trend of current was observed at -2 V and +2 V. (c) Schematic

212

illustrations of the wettability and charge distribution changes in the nanochannel.

213

To clearly figure out whether the sensitivity of the FeIII detection by funnel-shaped bioinspired

214

nanochannel is based on the enhanced critical section, we fabricated the widely studied conical-

215

shaped nanochannels, which possess a tip point not a cylinder as the critical section. The DOPA-

216

modified conical-shape nanochannel was used as a control experiment. As shown in Figure 7a,

217

when the concentration of FeIII was 0.01 nM, the I-V curve coincided with the DOPA-modified I-

ACS Paragon Plus Environment

13

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 14 of 27

218

V curve. That’s to say, the conical-shaped nanochannel cannot recognize the ultralow level FeIII

219

(Table.S1). Hereafter, we increased the concentration of FeIII to 10 nM, the ions current value

220

experienced a slight fluctuation: from -22.7 nA to 25.4 nA. With the further increasing of the

221

FeIII concentration, the ions current value at ± 2 V tended to be stable (Figure 7b). Normally, the

222

nanochannels with small ion current values were more sensitive. The conical nanochannel was

223

etched with smaller pore size in this experiment (Figure S5). However, the response to FeIII had

224

obvious weakness compared with the funnel-shaped nanochannel, which provided strong

225

evidence that the ultra-sensitive detection ability did come from the function of the extended

226

critical section.

227 228

Figure 7. FeIII response in DOPA-modified conical-shaped nanochannels. (a)The I-V curves of

229

the DOPA-modified conical-shaped nanochannels with increasing FeIII concentration. (b) With

230

the increasing FeIII concentration, the change trend of ion current was observed at ± 2 V.

231

ACS Paragon Plus Environment

14

Page 15 of 27 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

232

Table 2. Methods involved in the sensitive detection of FeIII by different technology in recently

233

years. Materials (Methods)

LOD (M)

Reference

Luminescent Cd(II)–Organic Frameworks with Chelating NH2 Sites

2.7×10-6

[18]

Fluorescent Boron Nitride Quantum Dots

3.0×10-7

[8]

Zr(IV)-Based Metal−Organic Frameworks

2.8×10-7

[17]

Dendrimer-Based Electropolymerized Microporous Film

8.5×10-8

[47]

Rhodamine-Functionalized Graphene Quantum Dots

2.0×10-8

[13]

Luminescent N,S Co-doped Graphene Quantum dots

8.0×10-9

[15]

Nitrogen and Phosphorus Co-Doped Carbon Nanodots

1.8×10-9

[12]

Ligninsulfonate/graphene Quantum Dots Composites

5.0×10-10

[14]

Fluorescent Organic Nanoparticles

1.0×10-10

[7]

π-Plasmon Absorption of Carbon Nanotubes

1.0×10-11

[11]

234 235

With an extended cylindrical segment, the funnel-shaped nanochannel achieved ultra-sensitive

236

detection of FeIII. Previously, many works involved in the sensitive detection of FeIII were

237

reported. Among them, the synthesis fluorescent probes are thoroughly discussed and

238

comprehensive applied in FeIII detection. Besides the fluorescent probes, the new methods such

239

as MOFs, Films46, carbon nanotubes, graphene quantum dots and so on, have gradually

240

developed. As shown in Table 2, we summarized the articles published in the past two years on

241

the detection of iron ions. The different methods, materials and limits of detection are listed in

242

the table. Compare to the system in this article, the simple structure is one of its major

243

advantages. Unlike the artificial bioinspired nanochannels, the complex process and expensive

244

cost of sensitive probes or carbon materials make the FeIII detection technology cannot be

ACS Paragon Plus Environment

15

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 16 of 27

245

promoted. Thus, the funnel-shaped nanochannels modified with functionalized molecule will

246

find application in the ultra-sensitive ion detection.

247

Figure 8. Stability and repeatability of the FeIII activated ionic nanochannel. (a) The reversible

248

ionic currents before and after removing of FeIII by adding EDTA-2Na. (b) Stability and

249

responsive switchability of the DOPA-modified nanochannels at -2 V.

250

FeIII activated ionic nanochannel also exhibited good stability and responsive switchability,

251

which could be demonstrated by the addition and removal of FeIII. Figure 8a showed the I-V

252

curves of the DOPA-modified nanochannels before and after immersing in solution and then

253

treated with EDTA-2Na respectively. By immersing in FeCl3, the nanochannel changed from “on”

254

(relatively high ion current value: -38.1 nA at -2 V) state to “off” (ion transport was restricted

255

and showed low ion current value: -6.2 nA at -2 V) state. When EDTA-2Na was added into the

256

system, the I-V curve returned to the “on” state. As the binding capacity of EDTA-2Na to FeIII

257

was stronger than that of DOPA with FeIII, EDTA-2Na could take FeIII from DOPA-FeIII cross-

258

linked chelates47 and the ionic current recovered to the initial DOPA-modified state. As shown in

259

the Figure 8b, ON/OFF states switched upon alternating introduction of DOPA and EDTA-2Na,

ACS Paragon Plus Environment

16

Page 17 of 27 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

260

and no damping of the ionic current was observed after several cycles, which reflected the high

261

reversibility and repeatability of the system.

262

Conclusion

263

In summary, an ultra-low concentration of FeIII detection method was successfully realized by

264

immobilizing DOPA in funnel-shaped nanochannels. Owing to the special structure, the funnel-

265

shaped nanochannel combining with functional molecule provided a new platform to detect trace

266

amounts of FeIII ions. Specifically, this system can directly realize the ultra-trance FeIII detection

267

with concentration of 10-3 nM. Furthermore, with the excellent stability and switchability of the

268

funnel-shaped nanochannels, our proposed platform may have potential applications in high

269

sensitively ion detection fields, such as biological toxicity examination and water quality

270

monitoring.

271

Experimental Section

272

Materials: The reagents used in this experiment were all analytically grade. NaOH, KCl,

273

HCOOH,

N-(3-Dimethylaminopropyl)-N-ethylcarbodiimide

hydrochloride

(EDC),

N-

274

Hydroxysul fosuccinimide sodium salt (NHS), DOPA, Tris-HCl, FeCl3, EDTA-2Na were

275

purchased from Sinopharm Chemical Reagent Beijing Co., Ltd. (SCRC, China) and J&K Beijing

276

Co., Ltd. Poly(ethylene terephthalate) (PET) membranes (thickness of 12 um) (HostaphanRN12,

277

Hoechst, density of 106 cm-2) were irradiated at the linear accelerator UNILAC (GSI, Darmstadt)

278

with swift heavy ions (Au) which have an energy of 11.4 MeV per nucleon. The fabrication of

279

nanochannels in the PET membrane was accomplished by asymmetric etching of the damage

280

trails which were coursed by the heavy ions (Au, Bi or U) passing through the membrane. Before

ACS Paragon Plus Environment

17

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 18 of 27

281

the chemical etching process, the PET films were exposed to UV light (365 nm, 20 W) for 1 h

282

from each side to improve the etching properties.

283

Fabrication of funnel-shaped nanochannel: The funnel-shaped nanochannels were prepared

284

by an asymmetric track etching technology on a PET membrane containing 106 nanopores/cm2,

285

approximately. Concentrated NaOH has been selected as the etchant reagent for preparing bio-

286

inspired nanochannels on PET membrane. At first, the PET membrane was irradiated with single

287

swift heavy ions (Au) to obtain damage trail; then, the membranes were irradiated under UV

288

light (365 nm) for 2 h from both sides in order to make the film more conducive to etching; last,

289

start etching. The specific process were as follows: the etching (NaOH, 9 M) and the stopping

290

solution (1 M KCl and 1 M HCOOH) are added in two different sides of the reaction cell (Figure

291

S6).

292

Owing to its special construction, this process was carried out by two steps: one for conical

293

section and the other for cylinder section. The Pt electrode was used to detect the current change

294

under the voltage 1 V during the etching process. When the transmembrane ionic current

295

achieved an increasing from 10-12 A to 10-9 A, which meant several of the nanochannels opened

296

and the conical part had been presented. Remove the membrane quickly and switch to a 60 °C

297

reaction pool to continue etching. The etching (2 M NaOH) and stop solution (1 M KCl and 1 M

298

HCOOH) were both heated to 60 °C. In particular, the cylindrical portion was obtained by

299

etching on the same side. Owing to the temperature have more profound impact than the

300

concentration of the etching solution, generally, the higher temperature process lasted for 4~5

301

minutes. Wait until the ion currents reach to a certain number, then stop etching. Remove the

302

etching solution and add the stop solution to the pool quickly. It was worth noting that the NaOH

303

could not be cleaned completely, thus, washing the pool more than three times was very

ACS Paragon Plus Environment

18

Page 19 of 27 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

304

necessary. The fabrication of the funnel-shaped nanochannel would finish until the current was

305

stable. Finally, the prepared membrane was immersed in Milli-Q water (18.2 MΩ) for next step.

306

The big size pore (the radius of base side approximate to 400 nm) of the nanochannels can be

307

observed under scanning electron microscopy. The small size pore (the radius of tip side

308

approximate to 10 nm) can be observed in the profile.

309

Functionalization with DOPA: The functional molecular DOPA was immobilized on the inner

310

surface of the funnel-shaped nanochannel by chemical modification. After the ionic trail-etching,

311

a large number of carboxyl (–COOH) functional groups were produced in the inner face of the

312

funnel-shaped nanochannel. Above all, the PET membranes were activated in mixture solution (2

313

mL) consist of EDC (30 mg) and NHS (6 mg) for 1 hour. In this process, the –COOH were

314

activated into a more easily reactive group. Single DOPA molecular was modified in the

315

multiple nanochannels at acidic solution (dopamine 20 mM, 0.1 M Tris-HCl buffer, pH 5.7)

316

mainly because acidic conditions can effectively inhibit the self-polymerization of DOPA

317

molecules, so as to ensure that the modification in the pore is monomer DOPA. The modification

318

was accomplished by one step coupling reaction of the amino in DOPA and the carboxyl acid in

319

surface. Chemical modification cannot modify all of the activated carboxyl groups with DOPA

320

due to the inevitable byproduct. After modification, the membrane was washed with Milli-Q

321

water (18.2 MΩ) for more than three times.

322

Functionalized nanochannel chelating with FeIII ions: After functionalization with DOPA,

323

FeCl3 solution prepared in Tris-HCl was introduced on the both side of the funnel-shaped

324

nanochannels. The immobilization of FeIII lasted for 2h at room temperature. After that, the

325

membrane was washed three times and reserved for backup.

ACS Paragon Plus Environment

19

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 20 of 27

326

Supporting Information

327

Experimental details about the fabrication process of funnel-shaped nanochannels and the post

328

modification of DOPA. Figures about X-ray photoelectron spectroscopy of a planar PET

329

membrane, contact angle measurement, diagram of the experimental facility, I-V curves of the

330

concentration measurement, and the reaction equation between DOPA and FeIII. Table about the

331

different methods involve in the detection of Iron ions.

332

Author Contributions

333



334

Notes

335

The authors declare no competing financial interests.

336

Acknowledgements

337

The authors thank the Material Science Group of GSI (Darmstadt, Germany) for providing the

338

ion-irradiated samples. This work was supported by the National Key R&D Program of China

339

(2017YFA0206904, 2017YFA0206900), the National Natural Science Foundation (21625303,

340

51673206, 21434003), and the Key Research Program of the Chinese Academy of Sciences

341

(QYZDY-SSW-SLH014).

These authors contributed equally to this work.

342 343 344

ACS Paragon Plus Environment

20

Page 21 of 27 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

ACS Applied Materials & Interfaces

345

References

346

(1) Hentze, M. W.; Muckenthaler, M. U.; Galy, B.; Camaschella, C. Two to Tango: Regulation

347 348 349 350 351 352 353

of Mammalian Iron Metabolism. Cell 2010, 142, 24-38. (2) Dixon, S. J.; Stockwell, B. R. The Role of Iron and Reactive Oxygen Species in Cell Death. Nat. Chem. Biol. 2014, 10, 9-17. (3) Zecca, L.; Youdim, M. B.; Riederer, P.; Connor, J. R.; Crichton, R. R. Iron, Brain Ageing and Neurodegenerative Disorders. Nat. Rev. Neurosci. 2004, 5, 863-873. (4) Enami, S.; Sakamoto, Y.; Colussi, A. J. Fenton Chemistry at Aqueous Interfaces. Proc. Natl. Acad. Sci. U. S. A. 2014, 111, 623-628.

354

(5) Eid, R.; Arab, N. T.; Greenwood, M. T. Iron Mediated Toxicity and Programmed Cell Death:

355

a review and a Re-examination of Existing Paradigms. Biochim. Biophys. Acta BBA - Mol.

356

Cell Res. 2017, 1864, 399-430.

357

(6) Song, Y.; Zhu, C.; Song, J.; Li, H.; Du, D.; Lin, Y. Drug-Derived Bright and Color-Tunable

358

N-Doped Carbon Dots for Cell Imaging and Sensitive Detection of Fe3+ in Living Cells.

359

ACS Appl. Mater. Interfaces 2017, 9, 7399-7405.

360

(7) Yang, Y.; Wang, X.; Cui, Q.; Cao, Q.; Li, L. Self-Assembly of Fluorescent Organic

361

Nanoparticles for Iron(III) Sensing and Cellular Imaging. ACS Appl. Mater. Interfaces

362

2016, 8, 7440-7448.

363

(8) Huo, B.; Liu, B.; Chen, T.; Cui, L.; Xu, G.; Liu, M.; Liu, J. One-Step Synthesis of

364

Fluorescent Boron Nitride Quantum Dots via a Hydrothermal Strategy Using Melamine as

365

Nitrogen Source for the Detection of Ferric Ions. Langmuir 2017, 33, 10673-10678.

ACS Paragon Plus Environment

21

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

366

(9) Yao, Q.; Lu, B.; Ji, C.; Cai, Y.; Yin, M. Supramolecular Host-Guest System as Ratiometric

367

Fe(3+) Ion Sensor Based on Water-Soluble Pillar[5]arene. ACS Appl. Mater. Interfaces

368

2017, 9, 36320-36326.

369

Page 22 of 27

(10) Zhou, Z.; Shen, Y.; Li, Y.; Liu, S.; Zhang, Y. Chemical Cleavage of Layered Carbon Nitride

370

with Enhanced Photoluminescent Performances and Photoconduction. ACS Nano 2015, 9,

371

12480-12487.

372

(11) Cheung, W.; Patel, M.; Ma, Y.; Chen, Y.; Xie, Q.; Lockard, J. V.; Gao, Y.; He, H. π-

373

Plasmon Absorption of Carbon Nanotubes for the Selective and Sensitive Detection of Fe3+

374

Ions. Chem. Sci. 2016, 7, 5192-5199.

375

(12) Shi, B.; Su, Y.; Zhang, L.; Huang, M.; Liu, R.; Zhao, S. Nitrogen and Phosphorus Co-

376

Doped Carbon Nanodots as a Novel Fluorescent Probe for Highly Sensitive Detection of

377

Fe(3+) in Human Serum and Living Cells. ACS Appl. Mater. Interfaces 2016, 8, 10717-

378

10725.

379

(13) Guo, R.; Zhou, S.; Li, Y.; Li, X.; Fan, L.; Voelcker, N. H. Rhodamine-Functionalized

380

Graphene Quantum Dots for Detection of Fe(3+) in Cancer Stem Cells. ACS Appl. Mater.

381

Interfaces 2015, 7, 23958-23966.

382

(14) Xu, L.; Mao, W.; Huang, J.; Li, S.; Huang, K.; Li, M.; Xia, J.; Chen, Q. Economical, Green

383

Route to Highly Fluorescence Intensity Carbon Materials Based on

384

Ligninsulfonate/Graphene Quantum Dots Composites: Application as Excellent Fluorescent

385

Sensing Platform for Detection of Fe3+ Ions. Sens. Actuat. B: Chem. 2016, 230, 54-60.

ACS Paragon Plus Environment

22

Page 23 of 27 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

386

ACS Applied Materials & Interfaces

(15) Shen, C.; Ge, S.; Pang, Y.; Xi, F.; Liu, J.; Dong, X.; Chen, P. Facile and Scalable

387

Preparation of Highly Luminescent N,S Co-doped Graphene Quantum Dots and Their

388

Application for Parallel Detection of Multiple Metal Ions. J. Mater. Chem. B 2017, 5, 6593-

389

6600.

390

(16) Chen, D.-M.; Zhang, N.-N.; Liu, C.-S.; Du, M. Template-directed Synthesis of A

391

Luminescent Tb-MOF Material for Highly Selective Fe3+ and Al3+ Ion Detection and

392

VOC Vapor Sensing. J. Mater. Chem. C 2017, 5, 2311-2317.

393

(17) Wang, B.; Yang, Q.; Guo, C.; Sun, Y.; Xie, L. H.; Li, J. R. Stable Zr(IV)-Based Metal-

394

Organic Frameworks with Predesigned Functionalized Ligands for Highly Selective

395

Detection of Fe(III) Ions in Water. ACS Appl. Mater. Interfaces 2017, 9, 10286-10295.

396

(18) Zhao, D.; Liu, X.-H.; Zhao, Y.; Wang, P.; Liu, Y.; Azam, M.; Al-Resayes, S. I.; Lu, Y.;

397

Sun, W.-Y. Luminescent Cd(ii)–Organic Frameworks with Chelating NH2 Sites for

398

Selective Detection of Fe(iii) and Antibiotics. J. Mater. Chem. A 2017, 5, 15797-15807.

399

(19) Ali, M.; Ahmed, I.; Nasir, S.; Ramirez, P.; Niemeyer, C. M.; Mafe, S.; Ensinger, W. Ionic

400

Transport through Chemically Functionalized Hydrogen Peroxide-Sensitive Asymmetric

401

Nanopores. ACS Appl. Mater. Interfaces 2015, 7, 19541-19545.

402

(20) Zhang, H.; Hou, X.; Hou, J.; Zeng, L.; Tian, Y.; Li, L.; Jiang, L. Synthetic Asymmetric-

403

Shaped Nanodevices with Symmetric pH-Gating Characteristics. Adv. Funct. Mater. 2015,

404

25, 1102-1110.

405 406

(21) Xu, Y.; Sui, X.; Jiang, J.; Zhai, J.; Gao, L. Smooth Muscle Cell-Mimetic CO-Regulated Ion Nanochannels. Adv. Mater. 2016, 28, 10780-10785.

ACS Paragon Plus Environment

23

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

407

(22) Zhao, X. P.; Wang, S. S.; Younis, M. R.; Xia, X. H.; Wang, C. Asymmetric Nanochannel-

408

Ionchannel Hybrid for Ultrasensitive and Label-Free Detection of Copper Ions in Blood.

409

Anal. Chem. 2018, 90, 896-902.

410

Page 24 of 27

(23) Wang, J.; Hou, J.; Zhang, H.; Tian, Y.; Jiang, L. Single Nanochannel-Aptamer-Based

411

Biosensor for Ultrasensitive and Selective Cocaine Detection. ACS Appl. Mater. Interfaces

412

2018, 10, 2033-2039.

413

(24) Sun, Z.; Liao, T.; Zhang, Y.; Shu, J.; Zhang, H.; Zhang, G. J. Biomimetic Nanochannels

414

Based Biosensor for Ultrasensitive and Label-Free Detection of Nucleic Acids. Biosens.

415

Bioelectron. 2016, 86, 194-201.

416 417

(25) Singh, K. P. Ion Current Rectification Influenced by Length and Location of Surface Charge in Fluidic Unipolar Conical Nanopores. Sens. Actuat. B: Chem. 2016, 230, 493-500.

418

(26) Dekker, C. Solid-state Nanopores. Nat. Nanotechnol. 2007, 2, 209-215.

419

(27) Hou, X.; Guo, W.; Jiang, L. Biomimetic Smart Nanopores and Nanochannels. Chem. Soc.

420

Rev. 2011, 40, 2385-2401.

421

(28) Ali, M.; Ramirez, P.; Tahir, M. N.; Mafe, S.; Siwy, Z.; Neumann, R.; Tremel, W.; Ensinger,

422

W. Biomolecular Conjugation Inside Synthetic Polymer Nanopores via Glycoprotein-lectin

423

Interactions. Nanoscale 2011, 3, 1894-1903.

424

(29) Hou, X.; Yang, F.; Li, L.; Song, Y.; Jiang, L.; Zhu, D. A Biomimetic Asymmetric

425

Responsive Single Nanochannel. J. Am. Chem. Soc. 2010, 132, 11736-11742.

426 427 428 429

(30) Zhang, H.; Hou, X.; Zeng, L.; Yang, F.; Li, L.; Yan, D.; Tian, Y.; Jiang, L. Bioinspired Artificial Single Ion Pump. J. Am. Chem. Soc. 2013, 135, 16102-16110. (31) Sheng, Q.; Xie, Y.; Li, J.; Wang, X.; Xue, J. Transporting An Ionic-liquid/Water Mixture in a Conical Nanochannel: a Nanofluidic Memristor. Chem. Commun. 2017, 53, 6125-6127.

ACS Paragon Plus Environment

24

Page 25 of 27 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

430 431 432

ACS Applied Materials & Interfaces

(32) Apel, P. Y.; Blonskaya, I. V.; Orelovitch, O. L.; Ramirez, P.; Sartowska, B. A. Effect of Nanopore Geometry on Ion Current Rectification. Nanotechnology 2011, 22, 175302. (33) Xiao, K.; Xie, G.; Zhang, Z.; Kong, X. Y.; Liu, Q.; Li, P.; Wen, L.; Jiang, L. Enhanced

433

Stability and Controllability of an Ionic Diode Based on Funnel-Shaped Nanochannels with

434

an Extended Critical Region. Adv. Mater. 2016, 28, 3345-3350.

435

(34) Xiao, K.; Chen, L.; Zhang, Z.; Xie, G.; Li, P.; Kong, X. Y.; Wen, L.; Jiang, L. A Tunable

436

Ionic Diode Based on a Biomimetic Structure-Tailorable Nanochannel. Angew. Chem., Int.

437

Ed. 2017, 56, 8168-8172.

438

(35) Wu, K.; Xiao, K.; Chen, L.; Zhou, R.; Niu, B.; Zhang, Y.; Wen, L. Biomimetic Voltage-

439

Gated Ultrasensitive Potassium-Activated Nanofluidic Based on a Solid-State Nanochannel.

440

Langmuir 2017, 33, 8463-8467.

441

(36) Zeng, H.; Hwang, D., S.; Israelachvili, J., N.; Waite, J., H. Strong Reversible Fe 3+-

442

mediated Bridging between Dopa-Containing Protein Films in Water. Proc. Natl. Acad. Sci.

443

U. S. A. 2010, 107, 12850-12853.

444

(37) Kim, B. J.; Cheong, H.; Hwang, B. H.; Cha, H. J. Mussel-Inspired Protein Nanoparticles

445

Containing Iron(III)-DOPA Complexes for pH-Responsive Drug Delivery. Angew. Chem.,

446

Int. Ed. 2015, 54, 7318-7322.

447

(38) Apel, P. Y.; Korchev, Y. E.; Siwy, Z.; Spohr, R.; Yoshida, M. Diode-Like Single-Ion Track

448

Membrane Prepared by ElectroStopping. Nucl. Instrum. Methods Phys. Res., Sect. B 2001,

449

184, 337-346.

450

(39) Perez-Mitta, G.; Albesa, A. G.; Trautmann, C.; Toimil-Molares, M. E.; Azzaroni, O.

451

Bioinspired Integrated Nanosystems Based on Solid-state Nanopores: "iontronic"

452

Transduction of Biological, Chemical and Physical Stimuli. Chem. Sci. 2017, 8, 890-913.

ACS Paragon Plus Environment

25

ACS Applied Materials & Interfaces 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

453

Page 26 of 27

(40) Gogoi, N.; Barooah, M.; Majumdar, G.; Chowdhury, D. Carbon Dots Rooted Agarose

454

Hydrogel Hybrid Platform for Optical Detection and Separation of Heavy Metal Ions. ACS

455

Appl. Mater. Interfaces 2015, 7, 3058-3067.

456

(41) Liu, L.; Wang, X.; Wang, N.; Peng, T.; Wang, S. Bright, Multi-responsive, Sky-Blue

457

Platinum(II) Phosphors Based on a Tetradentate Chelating Framework. Angew. Chem., Int.

458

Ed. 2017, 56, 9160-9164.

459 460

(42) Zdybel, M.; Chodurek, E.; Pilawa, B. EPR Studies of DOPA–Melanin Complexes with Fe(III). Appl. Magn. Reson. 2010, 40, 113-123.

461

(43) Kim, B. J.; Kim, S.; Oh, D. X.; Masic, A.; Cha, H. J.; Hwang, D. S. Mussel-Inspired

462

Adhesive Protein-Based Electrospun Nanofibers Reinforced by Fe(III)–DOPA

463

Complexation. J. Mater. Chem. B 2015, 3, 112-118.

464

(44) Kim, S.; Moon, J.-M.; Choi, J. S.; Cho, W. K.; Kang, S. M. Mussel-Inspired Approach to

465

Constructing Robust Multilayered Alginate Films for Antibacterial Applications. Adv.

466

Funct. Mater. 2016, 26, 4099-4105.

467

(45) Liu, Q.; Lu, X.; Li, L.; Zhang, H.; Liu, G.; Zhong, H.; Zeng, H. Probing the Reversible

468

Fe3+-DOPA-Mediated Bridging Interaction in Mussel Foot Protein-1. J. Phys. Chem. C

469

2016, 120, 21670-21677.

470

(46) Ma, H.; Li, F.; Li, P.; Wang, H.; Zhang, M.; Zhang, G.; Baumgarten, M.; Müllen, K. A

471

Dendrimer-Based Electropolymerized Microporous Film: Multifunctional, Reversible, and

472

Highly Sensitive Fluorescent Probe. Adv. Funct. Mater. 2016, 26, 2025-2031.

473 474

(47) Kim, S.; Gim, T.; Kang, S. M. Stability-Enhanced Polydopamine Coatings on Solid Substrates by Iron (III) Coordination. Prog. Org. Coat. 2014, 77, 1336-1339.

475

ACS Paragon Plus Environment

26

Page 27 of 27 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

476

ACS Applied Materials & Interfaces

Table of contents

477

ACS Paragon Plus Environment

27