Speeding up the line-scan Raman imaging of living cells by deep

May 7, 2019 - In this paper, we developed an artificial intelligence assisted fast Raman imaging method over the already fast line scan Raman imaging ...
0 downloads 0 Views 4MB Size
Subscriber access provided by IDAHO STATE UNIV

Article

Speeding up the line-scan Raman imaging of living cells by deep convolutional neural network Hao He, Mengxi Xu, Cheng Zong, Peng Zheng, Lilan Luo, Lei Wang, and Bin Ren Anal. Chem., Just Accepted Manuscript • Publication Date (Web): 07 May 2019 Downloaded from http://pubs.acs.org on May 7, 2019

Just Accepted “Just Accepted” manuscripts have been peer-reviewed and accepted for publication. They are posted online prior to technical editing, formatting for publication and author proofing. The American Chemical Society provides “Just Accepted” as a service to the research community to expedite the dissemination of scientific material as soon as possible after acceptance. “Just Accepted” manuscripts appear in full in PDF format accompanied by an HTML abstract. “Just Accepted” manuscripts have been fully peer reviewed, but should not be considered the official version of record. They are citable by the Digital Object Identifier (DOI®). “Just Accepted” is an optional service offered to authors. Therefore, the “Just Accepted” Web site may not include all articles that will be published in the journal. After a manuscript is technically edited and formatted, it will be removed from the “Just Accepted” Web site and published as an ASAP article. Note that technical editing may introduce minor changes to the manuscript text and/or graphics which could affect content, and all legal disclaimers and ethical guidelines that apply to the journal pertain. ACS cannot be held responsible for errors or consequences arising from the use of information contained in these “Just Accepted” manuscripts.

is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Published by American Chemical Society. Copyright © American Chemical Society. However, no copyright claim is made to original U.S. Government works, or works produced by employees of any Commonwealth realm Crown government in the course of their duties.

Page 1 of 23 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Analytical Chemistry

1

Speeding up the line-scan Raman imaging of living

2

cells by deep convolutional neural network

3 4 5 6

Hao He1), Mengxi Xu2), Cheng Zong2), Peng Zheng1), Lilan Luo1), Lei Wang*,1) and Bin Ren2)

7 8 9 10 11

1School 2

of Aerospace Engineering, Xiamen University, Xiamen, 361005, China

The MOE Key Laboratory of Spectrochemical Analysis and Instrumentation, State Key

Laboratory of Physical Chemistry of Solid Surfaces, Collaborative Innovation Center of Chemistry for Energy Materials (iChEM), College of Chemistry and Chemical Engineering, Xiamen University, Xiamen 361005, China * Email: [email protected]

12 13

Abstract

14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

Raman imaging is a promising technique that allows the spatial distribution of different components in the sample to be obtained by using the molecular fingerprint information of individual species. However, the imaging speed are the bottleneck for the current Raman imaging methods to monitor the dynamic process of living cells. In this paper, we developed an artificial intelligence assisted fast Raman imaging method over the already fast line scan Raman imaging method. The reduced imaging time is realized by widening the slit and laser beam, and scanning the sample with a large scan step. The imaging quality is improved by a data-driven approach to train a deep convolutional neural network (CNN), which statistically learns to transform low resolution images acquired at a high speed into high resolution ones that previously were only possible with a low imaging speed. Accompany with the improvement of the image resolution, the deteriorated spectral resolution as a consequence of a wide slit is also restored, thereby the fidelity of the spectral information is retained. The imaging time can be reduced to within one minute, which is about five times faster than the state-of-the-art line scan Raman imaging techniques without sacrificing spectral and spatial resolution. We then demonstrate the reliability of the current method using fixed cells. We finally used the method to monitor the dynamic evolution process of living cells. Such an imaging speed opens door to the label-free observation of cellular events with conventional Raman microscopy.

ACS Paragon Plus Environment 1

Analytical Chemistry 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

35

Keywords: CNN; Line-scan; Raman imaging; human cancer cell;

36 37

Introduction

38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74

Raman imaging is a noninvasive and label-free optical method and has played a significant role in understanding many life processes1-8. Compared with conventional imaging techniques, Raman spectroscopy can obtain molecular fingerprint information from single cells to help a comprehensive understanding of biochemical processes. However, the Raman signals of most biomolecules are so weak that a long acquisition time is required to obtain a clear Raman image, which makes it difficult to track the dynamic biological activities of living samples. Therefore, it is highly desired to speed up the Raman imaging. Wide-field imaging has been proposed to improve the imaging speed. In this way, the sample is illuminated by a large laser spot and the Raman light of a particular frequency from the illuminated area is selected by a narrow band pass filter and imaged on the CCD camera. A wide-field Raman imaging system can now achieve a temporal resolution as fast as 20 ms9. However, this technique has to sacrifice the spectral information of the full Raman spectrum other than the particular frequency of interest, which hinders its application in multi-component analysis. On the other hand, stimulated Raman scattering (SRS) and coherent anti-Stokes Raman Scattering (CARS) microscopy can achieve a video rate imaging speed using the non-linear Raman effect10, which is receiving increasing interest for the label free study of biological samples. Its imaging speed can be further improved by sampling only ~20% pixels of the three-dimensional spectroscopic image stack and recovering the spectral signatures and concentration maps with a non-negative matrix factorization algorithm11. However, spectral window (c.a. 200 cm-1) is yet to be widened, the cost to be reduced and the possible laser damage to be avoided before its wide application. Line-scan Raman microscopy is a promising fast Raman imaging technique receiving increasing interests for imaging single living cells. For instance, Fujita group12 used the technique to observe the molecular dynamics in apoptotic cells using Raman signal of cytochrome c as a signature. Huang et al 13 employed it to study the drug release in living cells. In line scan technique, the sample is illuminated by a line-shaped laser and serval hundreds of spectra from the illuminated line can be acquired simultaneously. Then, the laser line is scanned over the sample perpendicular to the line to obtain Raman image containing the hyperspectral information. This technique not only retains the full spectral information of every pixels in the imaging area but also significantly shortens the data acquisition time compared with the conventional point-scan

ACS Paragon Plus Environment 2

Page 2 of 23

Page 3 of 23 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Analytical Chemistry

75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91

Raman microscope14. Its imaging speed is yet to be further improved for a wider application in monitoring the dynamic biological processes. Pavillon15 reported that the compressed sensing technique can increase the line scan imaging speed by significantly reduce the sampling rate down to 20%. The degraded image spatial resolution was then restored by solving a deconvolution model. However, the sparse sampling discarded a part of spatial information which would be difficult to retrieve by a deconvolution procedure. Here we present a novel way to speed up the line scan Raman imaging by widening the slit and laser beam, scanning the sample with a large scan step, and employing deep learning. More Raman light can enter the spectrometer through the wider slit to improve the sensitivity, which allows the use of a shorter exposure time to improve the imaging speed. A deep convolutional neural network (CNN) was then trained by a large number of imaging data of living cells to transform the acquired low-resolution images to high-resolution ones. We validated the CNN model by reconstructing high-resolution Raman images on the testing samples as well as a fixed cancer cell. The method was finally used for fast imaging the dynamic evolution of living human cancer cells.

92

Methods and materials

93

Fast speed line scan imaging

94 95 96 97 98 99 100 101 102 103 104 105 106 107

Figure 1 illustrates the schematic comparison between the conventional and our fast Raman imaging methods for obtaining high-resolution Raman images. Figure 1(a) displays the conventional line scan Raman imaging using a narrow slit (50 μm), small scan step (0.4 μm) and long exposure time. We denote it as low speed Raman imaging. On the other hand, Figure 1(b) demonstrates our current approach by using a wide slit (150 μm), expanded laser focus line (1.2 μm, under a 100 magnification objective), a large scan step (0.8 μm), short exposure time, and CNN method to obtain a high-resolution Raman image. Different from the conventional continuous scan mode, we scanned the sample with a different pattern to allow 1/3 of the laser focus line to overlap with the two neighboring lines along the scanning direction, which can save half of the scanning time. Indeed, each scan line contains three parts of intrinsic information for reconstructing the high-resolution image, which can be extracted with the deep learning method.

ACS Paragon Plus Environment 3

Analytical Chemistry 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123

Figure 1| A comparison of the fast speed Raman imaging method to obtain a high-resolution Raman image with the conventional line scan method. (a) Conventional low speed Raman imaging with an optimal set of narrow slit, tight line-focus laser beam, fine scan step and long exposure time. (b) fast speed Raman imaging with a wide slit, wide line-focus laser beam and large scan step and short exposure time. The obtained low-resolution Raman images are input to the CNN, whose output becomes a high-resolution one. Different from conventional imaging method, fast speed method is to scan the sample in a way that excitation laser beam overlapped with two neighboring lines.

An advantage of the wide slit is that more Raman light can be captured by the spectrometer, as the signal sensitivity increases linearly with the slit width (for more detailed experimental results see supplementary information Figure S1). This enables us to shorten the exposure time to 1/3 to obtain equal signal intensity compared with that using the narrow slit. Taking both the scanning time and exposure time into account, our method can achieve six times fast imaging speed of the conventional method, theoretically.

124

Reconstruct high-resolution image with CNN

125 126 127 128 129 130 131 132 133

CNN belongs to artificial neural network, which outperforms other neural networks in dealing with image-related tasks, such as classification16, reconstruction17-23, and semantic segmentation24, 25. Thanks to CNN’s power in feature extraction and pattern recognition, use of CNN can significantly enhance the imaging capability of an optical system 26, 27. Traditional single image super-resolution CNN aims at reconstructing the subsampled images into high-resolution ones, which is a typically ill-posed problem without analytical solution. Although the low frequency information of the image can be easily recovered through learning or interpolation, the high

ACS Paragon Plus Environment 4

Page 4 of 23

Page 5 of 23 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154

155 156 157 158 159 160 161

Analytical Chemistry

frequency information is still hard to be retrieved. The reason is that the high frequency information which changed rapidly may be treated as random noise, and is hard to be learned. Unlike the subsampling process which discards part of information, the low-resolution images produced by our method retain all the spectral information in the sampling area. This enables us to reconstruct the high-resolution image more effectively. A CNN directly learns an end-to-end mapping function between the lowand high- resolution image pair. However, living cells are changing continuously over time and it is unreliable to obtain the corresponding low- and highresolution Raman images through two successive scanning processes. Instead, a low-resolution Raman image generated by a wide slit can be simulated by a summing map of the corresponding high-resolution image generated by a narrow slit. In our experiment, the slit was set to 3 times of the usual case so that the measured signal intensity at a specific wavelength is the overlap of three neighboring parts with shifted wavenumber in the narrow slit mode. The degradation model can be understood as Figure 2, where m is the shifted pixel number along the wavenumber direction on the charge coupled device (CCD), which is about 2 pixels in our case. We then used silicon wafer as the sample to validate our degradation model. The simulation performance can be seen in the supplementary information (please see Figure S2).

Figure 2 The spectral degradation model of using a slit of three times width to scan the sample. In the wide slit mode, the measured intensity of position M at λn is the overlap of three shifted parts of A, B and C in the narrow slit mode. The degradation model can be simply classified as the equation in the figure. Where m denotes the shifted pixel number, which is related with the slit width (denote as W), pixel size (denote as S) of the CCD and magnification rate (denote as R) of the spectrometer. The equation can be written as m = W×R/S. In the Raman-11 system, a Czerny-Turner spectrometer (500

ACS Paragon Plus Environment 5

Analytical Chemistry 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188

Page 6 of 23

mm focal length) offers a 1:1 magnification rate and the pixel size of the CCD is 20 μm×20 μm.

We generated the low-resolution Raman image according to the degradation model discussed above. Before training, we inserted zeros between every two horizontal lines to let the low-resolution images have the same size with the high-resolution ones. Although the image after zero padding has the same pixel number with the high-resolution one, we still call it lowresolution image. Figure 3(a) illustrates the schematic diagram of reconstructing high-resolution image with a CNN, which consists of 3 convolutional layers. The convolution layers extract feature maps from the lowresolution image successively, and finally outputs a high-resolution one. The output image is expected to be as similar as possible to the ground truth of highresolution one. Figure 3(b) demonstrates the architecture of the convolutional layers, in which N feature maps are generated by convoluting the input images with N filters. These N feature maps are summed together and only one feature was output after activation with a Rectified Linear Unit (ReLU). ReLU28 can make the convergence much faster and still presents good quality. The output response of the ReLU can be described by Equation 1. X denotes the input image matrix, W denotes the filter (or weight), b denotes the bias, and  denotes the convolutional operation. (1) F( X)  max(0, W  X  b) Loss value is a direct indicator of the performance of CNN. It is used to evaluate the inconsistency of the neural network output with the true data, which is usually a non-negative real value function. As image reconstruction is a regression problem, we used mean square error (MSE) (see Equation 2) as the loss function. MSE 

1

r

c

 S(i, j )  Sˆ (i, j ) rc

2

(2)

i 1 j 1

189 190 191 192 193 194 195 196 197 198 199 200 201

S denotes the true image matrix, and Ŝ is the output of CNN. CNN learns the prior knowledge from the training samples, and updates its weights (W) and biases (b) to gradually decrease the loss and finally achieves a convergence. The update processes of these network parameters were achieved by the gradient descent algorithm. The gradients of the weights and biases can be calculated through the backpropagation algorithm29. We used Adam, which is a widely used and highly efficient optimization algorithm in the deep learning area30, to minimize the loss function to allow fast convergent. CNN is a complicate model with a lot of hyper parameters. The tuning of these parameters is of great importance for improving the performance of the model. The depth of the convolution layer, the filter size and number of each layer are the foremost factors which should be elaborately designed. A deeper CNN can produce better performance but requires a larger training data set.

ACS Paragon Plus Environment 6

Page 7 of 23 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221

Analytical Chemistry

We found that the filter size of 3×3 (f1=f2=f3=3) for each layer could produce a good result. A typical set of filter number for each layer is n1 = 64 and n2 = 128. The initial values of these filters are randomly extracted from a Gaussian distribution with zero mean and standard deviation of 0.001. The initial set up of the biases are 0. Batch size and learning rate are also important hyper parameters for CNN. Batch size is the number of samples which is fed to the CNN for each iteration. The CNN updates its weights and biases after the gradients of all samples in a batch have been calculated. Statistically, the calculated gradients are closer to their global values when there are more samples in a batch. In contrary, the gradients are noisier at a smaller batch, which will lead to a worse learning efficiency. Although a larger batch size can make the convergence to the global optimal station faster, it may slow down the convergence rate in practice31,32. Learning rate () is used to control the update speed of the weights and biases. For instance, in particular, a weight can be updated according to Equation 3, where i is the iteration indices and L denotes the loss function. It is important to choose a proper learning rate to avoid slow convergence at a small learning rate and divergence at a large learning rate. A typical set of the batch size and learning rate in our experiments are 20 and 0.001, respectively.  i 1  0.9   i   

L , Wi 1  Wi 1   i 1 Wi

ACS Paragon Plus Environment 7

(3)

Analytical Chemistry 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

222 223 224 225 226 227 228 229 230

Figure 3| Scheme of reconstruction of high-resoution Raman images. (a) The scheme of the CNN model to reconstruct the low-resolution image to a high-resolution one. The CNN model consists of 3 convolution layers. The convolution layers extract feature maps from the low-resolution image successively, and finally outputs a high-resolution one. The output image is expected to be as similar as possible with the true high-resolution one. (b) The architecture of the convolution layer, in which N feature maps are generated by convoluting the input image with N filters. These N feature maps are summed together and output one feature after activation with a Rectified Linear Unit (ReLU). The CNN updates its filters after very iteration until convergent.

231

Data preparation

232 233 234 235 236 237 238 239 240

All Raman hyperspectral data in this work were acquired by a fast line-scan Raman imaging system (Raman-11, Nanophoton, Figure S3). We collected 295 Raman hyperspectral data sets of living human cancer cells (mainly include: HeLa, CaSki, and TCA-8113A cells) under similar experimental conditions (slit width = 50 μm, scan step = 0.4 μm, exposure time per line = 10 s, laser source = 532 nm, laser power = 50 mW, oil-immersion objective: NA =1.49, 100 magnification). We then chose the wavenumber region of 2798 cm-1~3015 cm-1 (138 data points) to generate corresponding high-resolution and low-resolution Raman image pairs. For the convenience of CNN training, we cropped these

ACS Paragon Plus Environment 8

Page 8 of 23

Page 9 of 23 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Analytical Chemistry

241

Raman images to the same size of 45×200 pixels.

242

Results and discussions

243

Result on the testing sample

244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279

The peak area images were used as the training samples, and the CNN was trained on a NIVIDA TITAN XP GPU. The software was programed based on the Python language and TensorFlow framework (a deep learning software frame work developed by the Google Inc). We saved the CNN model that has the minimum loss value on the validation samples, and then the model was used to reconstruct high-resolution Raman images. The loss-iteration curves of the training and validation samples are demonstrated in supplementary Figure S4. Figure 4 demonstrates the result on the testing sample which has not been used to train the CNN. For comparison, we also presented the result of the linear interpolation. Figure 4(a) is the low-resolution image which is generated through binning the original high-resolution image in 4(b). Figure 4(c) is the reconstructed image of 4(a) through linear interpolation. Figure 4(d) is the reconstructed image of 4 (a) through CNN. The insets of Figure 4 (a)-(d) are the corresponding zooming images within the red rectangle areas. From the zooming images, it can be seen that CNN can recover the detailed image information very well. Figure 4(e)-(h) are the pixel intensity graphs along the red dotted line of the local zooming areas in image (a)-(d). As we can see, two nearby lipid droplets can be differentiated in the high-resolution image (b) and reconstructed image by CNN (d), whereas they are merged as one droplet in the low-resolution (a) and linear interpolation image (c). To evaluate the similarity of the reconstructed and the original highresolution image, we used 4 indicators to assess it. These indicators are peak signal to noise ratio (PSNR), image structural similarity (SSIM), mean absolute error (MAE) and standard deviation of the absolute error (STDAE). A bigger PSNR value indicates a better image quality. SSIM is a positive value between 0 and 1. A bigger SSIM value indicates that the target image is more similar to the reference. MAE and STDAE are used to evaluate the absolute error of the pixel intensity value of the reconstructed and the high-resolution Raman image. The formulas of these indicators can be found in the supplementary information. We evaluate the reconstructed images using the above indicators, and the results are presented in Table 1. We observed similar phenomenon on different testing samples. The CNN can increase ~5% of PSNR and ~4% of SSIM, whereas decrease ~10% of MAE and ~20% of STDAE compared with the linear interpolation method. More results can be seen in the supplementary information Figure S5.

ACS Paragon Plus Environment 9

Analytical Chemistry 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

280 281 282 283 284 285 286 287 288 289 290 291

292 293 294 295 296 297 298 299

Page 10 of 23

Figure 4| Comparison of reconstructing high-resolution Raman images on testing sample with CNN and linear interpolation method. (a) Low-resolution Raman image which is the binning map of (b). (b) High-resolution Raman image. (c) The reconstructed image of (a) through linear interpolation. (d) The reconstructed image of (a) through CNN. The right-down corners of (b) -(d) are the corresponding local zooming images within the red rectangle areas. The image reconstructed by the CNN shows high similarity with the original image. (e)-(h) The pixel intensity graphs along the red dotted line of the local zooming areas in image (a)-(d). As we can see, two nearby features can be differentiated in the high-resolution image (b) and the image reconstructed by CNN (d), while they are merged as one in the low-resolution (a) and linear interpolation image (c). Table 1 Image quality evaluation

PSNR

SSIM

MAE

STDAE

Fig.4(c) to 4(b)

33.77 dB

0.89

0.0130

0.0158

Fig.4(d) to 4(b)

35.36 dB

0.92

0.0116

0.0125

We further showed that the hyperspectral image stack can be recovered in the similar way. In this case, the low-resolution hyperspectral image stacks were split into single wavenumber images and fed into the CNN model, then the high-resolution hyperspectral image stacks were output. We chose the wavenumber window 1408 cm-1~1485 cm-1 and 2798 cm-1~3015 cm-1 as the target to carry out the following experiments. Figures 5(a), (b) and (c) are the low-, measured high- and recovered high-

ACS Paragon Plus Environment 10

Page 11 of 23 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318

319 320 321 322 323

Analytical Chemistry

resolution Raman image of a cell at 1443 cm-1, respectively. We further extracted the local mean spectra within the red rectangle area marked on Figure 5(b) and presented them in Figure 5(d). Where the red and blue curve denotes the recovered and measured spectrum, respectively. It can be found that the recovered spectrum perfectly coincided with the measured one, and the full width at half maxima (FWHM) of the two spectra are almost identical. This fact indicates that the recovery is considerably reliable, also the lost spectral resolution as a result of the wide slit can be regained through the CNN. To quantitatively analyze the recovery accuracy, the normalized root mean square errors (RMSE) of the recovered Raman images to the measured ones at each single wavenumber were calculated and presented in Figure 5(e). The RMSE fluctuates in an acceptable minor region of 1%~5%. Furthermore, we repeated the same processes with 10 hyperspectral data of different cell samples which have the same size of 55220 pixels, and drew the average RMSE histogram in Figure 5(f). Figure 5(g)-(m) are the similar results as that demonstrated in Figure 5(a)-(f) but in the different wavenumber window of 2798 cm-1~3015 cm-1. The average normalized RMSEs are within 4%, which are much better than the 10% RMSE reported in ref 15.

Figure 5| Recovery of hyperspectral Raman image stacks of a cell. Raman image at 1443 cm-1: (a) Low-resolution image; (b) Original high-resolution image; (c) High-resolution image recovered by CNN. (d) Normalized mean Raman spectra (1408 cm-1~1485 cm-1) within the red rectangle area (contains 50 pixels) marked on (b). The blue and red color indicates the measured and the recovered spectrum,

ACS Paragon Plus Environment 11

Analytical Chemistry 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364

respectively. The recovered spectrum perfectly coincided with the measured one, and the FWHM of the two spectra are almost identical, which implies that the recovered spectrum is considerably reliable. Normalized RMSEs of the recovered to measured Raman images at each single wavenumber in the window of 1408 cm-1~1485 cm-1: (e) Current sample; (f) Average of 10 different cell samples with the same size of 55◊200 pixels. Raman image at 2951 cm-1: (g) Low-resolution image; (h) Original highresolution image; (i) High-resolution image recovered by CNN. (j) Normalized mean Raman spectra (2798 cm-1~3015 cm-1) within the black rectangle area (contains 50 pixels) marked on (h). The blue and red color indicates the measured and the recovered spectrum, respectively. Normalized RMSEs of the recovered to measured Raman images at each single wavenumber in the window of 2798 cm-1~3015 cm-1: (k) Current sample; (m) Average of 10 different cell samples.

Speeding up the line-scan Raman imaging of cells We then performed the conventional low speed and our fast speed line scan imaging of a fixed CaSki cell with Raman-11. The excitation laser source was 532 nm, laser power was 50 mW. The focused laser beam width on the sample was 3 μm under a ×100 oil-immersion objective (NA = 1.49), which can cover a slit width of 300 μm theoretically. For the sake of keeping the same laser power density, we let the laser beam status unchanged in the below experiments’ setup. For the low speed high resolution one, the slit width was set to 50 μm, the exposure time per scan was 10 s, and the scan step was 0.4 μm. Figure 6(a) shows the corresponding high-resolution Raman image of the fixed cell in the spectral range of 2913 cm-1~2951 cm-1 (C-H region) obtained with an acquisition time of 570 s. For the fast speed imaging, the slit width was set to 150 μm, the exposure time per scan was 4 s, and the scan step was 0.8 μm. Figure 6(b) shows the corresponding low-resolution Raman image of the same cell obtained with an acquisition time of 112 s, which is approximately 1/5 of Figure 6(a). Then the low-resolution image was input to the CNN to obtain the high-resolution image of Figure 6(c). We compared the reconstructed image, Figure 6(c), with the high-resolution image, Figure 6(a), to check whether the CNN model can reliably recover the information lost by fast scanning. It can be seen that Figure 6(c) is similar to Figure 6(a) and is much clearer than Figure 6(b), indicating that CNN can be successfully applied to real samples. Then we further carried out the same line scan experiments with a living CaSki cell. The parameters for the low speed and fast speed scanning were the same as the previous experiments. Figure 6(d) is the high-resolution image produced by the low speed scanning method, and the total data acquisition time was 370 s. Figure 6(e) is the low-resolution image of the same cell produced by the fast speed scanning method. The total data acquisition time of Figure 6(e) was 72 s, which is 1/5 of Figure 6(d). Then we used the CNN to transform Figure 6(e) into a high-resolution image shown in Figure 6(f). Surprisingly, we observed a different pattern in Figure 6(f) from that in Figure 6(d). Such a

ACS Paragon Plus Environment 12

Page 12 of 23

Page 13 of 23 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

365 366 367 368 369 370

371 372 373 374 375 376 377 378 379

Analytical Chemistry

difference can be understood by the dynamic change of intracellular species in time and space due to the life activities, which cannot be observed in the fixed cell. The results show the advantages of the current fast imaging method over that of the low speed imaging method in revealing the dynamic evolution of living cell.

Figure 6| Experimental results of fixed (a-c) and living (d-f) CaSki cells. (a) and (d) High-resolution Raman images produced by the conventional line scan imaging method. The slit was set to 50 μm, the scan step was 0.4 μm and the exposure time was 10 s per line. The image size of (a) is 57200 pixels and 37200 pixels for (d). (b) and (e) Low-resolution Raman images produced by fast speed imaging method. The slit was set to 150 μm, scan step was 0.8 μm, and the exposure time was 4 s per line. The image size is 28200 pixels for (b) and 18200 pixels for (d). (c) and (f) The high-resolution Raman images reconstructed by the CNN with the data of (b) and (e), respectively. The image size is 57200 pixels for (c) and 37200 pixels for (f). In (a) and (b) the cell was fixed by formaldehyde.

380

Conclusion

381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397

In this work, we demonstrate that a deep neural network can significantly improve the spatial resolution and imaging speed of line-scan Raman microscopes. This data-driven approach is solely based on training a deep convolutional neural network (DCNN), which statistically learn to transform low resolution and high-speed input images into high resolved ones. Larger slit and less scan step were used to improve the imaging speed but resulted in a low resolution image. A wider slit allows more Raman light to be detected, which reduced the acquisition time for each step. The 1/3 overlapping of the laser focus line with the two neighboring lines along the scanning direction not only saved half of the scanning time but also laid the foundation of current method, i.e., the signal from each scan line contain the three parts of intrinsic information for reconstructing the high-resolution image with CNN method. The CNN model trained with a large amounts Raman imaging data of living cells was successfully used to reconstruct high resolution Raman images from the lowresolution ones acquired by fast speed imaging method for fixed and living cells. Benefit from the elaborately recover of hyperspectral Raman image stack, the decayed spectral resolution as a result of wide slit can be restored. The current

ACS Paragon Plus Environment 13

Analytical Chemistry 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Page 14 of 23

398 399 400 401 402 403 404 405 406

method exhibits five times faster imaging speed without sacrificing the spectral and spatial resolution. We demonstrated a promising deep learning assisted line-scan Raman imaging method for label-free monitoring of the dynamic process of living cell and gathering high spatial and temporal molecular information with a sub-cellular resolution. Moreover, such an artificial intelligence assisted technique can also be applied to broad range of samples and be borrowed for other spectroscopic techniques. If spectral denoising algorithms33, 34 can be further used, we would expect further improvement in the imaging quality and speed of the current method, which is now undergoing.

407

Acknowledgements

408 409 410 411 412

This work is funded by the National Natural Science Foundation of China (21633005, 21373173, 21790354, and 21711530704), the Ministry of Science and Technology of China (2016YFA0200601) and the Collaborative Innovation Center of High-End Equipment Manufacturing in Fujian. Hao He, Mengxi Xu and Cheng Zong contributed equally to this work.

413

Associated Content

414 415 416 417 418 419

Supporting Information The equations of image quality indicators; The relation of Raman signal intensity with the slit width; Simulation performance of using narrow slit hyperspectral data to simulate the wide slit data; The schematic of the optical system; Training and validation loss curves; Additional testing result;

420

References

421 422 423 424 425 426 427 428 429 430 431 432 433 434 435

1.

Tu, Q.; Chang, C., Diagnostic applications of Raman spectroscopy. Nanomed-

Nanotechnol 2012, 8 (5), 545-558. 2.

Kong, K.;

Kendall, C.;

Stone, N.; Notingher, I., Raman spectroscopy for medical

diagnostics - From in-vitro biofluid assays to in-vivo cancer detection. Adv Drug Deliver Rev 2015, 89, 121-134. 3.

Paudel, A.;

Raijada, D.; Rantanen, J., Raman spectroscopy in pharmaceutical

product design. Adv Drug Deliver Rev 2015, 89, 3-20. 4.

Zavaleta, C.;

Chen, X.;

de la Zerda, A.;

Liu, Z.;

Keren, S.;

Cheng, Z.;

Schipper, M.;

Dai, H.; Gambhir, S. S., Noninvasive Raman spectroscopy in living mice for

evaluation of tumor targeting with carbon nanotubes. Nano Lett 2008, 8 (9), 2800-2805. 5.

Hartsuiker, L.;

Zeijen, N. J. L.;

Terstappen, L. W. M. M.; Otto, C., A comparison of

breast cancer tumor cells with varying expression of the Her2/neu receptor by Raman microspectroscopic imaging. Analyst 2010, 135 (12), 3220-3226. 6.

Ando, J.;

Palonpon, A. F.;

Sodeoka, M.; Fujita, K., High-speed Raman imaging of

cellular processes. Curr Opin Chem Biol 2016, 33, 16-24.

ACS Paragon Plus Environment 14

Page 15 of 23 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477

Analytical Chemistry

7.

Zheng, X. S.;

Hu, P.;

Cui, Y.;

Zong, C.;

Feng, J. M.;

Wang, X.; Ren, B., BSA-

Coated Nanoparticles for Improved SERS-Based Intracellular pH Sensing. Anal Chem 2014, 86 (24), 12250-12257. 8.

Mariani, M. M.;

Maccoux, L. J.;

Matthaus, C.;

Diem, M.;

Hengstler, J. G.;

Deckert, V., Micro-Raman Detection of Nuclear Membrane Lipid Fluctuations in Senescent Epithelial Breast Cancer Cells. Anal Chem 2010, 82 (10), 4259-4263. 9.

Wang, L.;

Dai, Y. Z.;

He, H.;

Lv, R. Q.;

Zong, C.; Ren, B., Dynamic Raman

imaging system with high spatial and temporal resolution. Rev Sci Instrum 2017, 88 (9). 10. Ozeki, Y.;

Umemura, W.;

Otsuka, Y.; Satoh, S.; Hashimoto, H.;

Sumimura, K.;

Nishizawa, N.;

Fukui, K.; Itoh, K., High-speed molecular spectral imaging of tissue with

stimulated Raman scattering. Nat Photonics 2012, 6 (12), 844-850. 11. Lin, H. N.;

Liao, C. S.;

Wang, P.;

Kong, N.; Cheng, J. X., Spectroscopic

stimulated Raman scattering imaging of highly dynamic specimens through matrix completion. Light-Sci Appl 2018, 7. 12. Okada, M.;

Smith, N. I.;

Palonpon, A. F.;

Endo, H.;

Kawata, S.;

Sodeoka, M.;

Fujita, K., Label-free Raman observation of cytochrome c dynamics during apoptosis. P Natl Acad Sci USA 2012, 109 (1), 28-32. 13. Huang, J.;

Zong, C.;

Shen, H.;

Cao, Y. H.;

Ren, B.; Zhang, Z. J., Tracking the

intracellular drug release from graphene oxide using surface-enhanced Raman spectroscopy. Nanoscale 2013, 5 (21), 10591-10598. 14. Palonpon, A. F.;

Sodeoka, M.; Fujita, K., Molecular imaging of live cells by Raman

microscopy. Curr Opin Chem Biol 2013, 17 (4), 708-715. 15. Pavillon, N.; Smith, N. I., Compressed sensing laser scanning microscopy. Optics Express 2016, 24 (26), 30038-30052. 16. Hu, W.;

Huang, Y.;

Wei, L.; Zhang, F.; Li, H. J. J. o. S., Deep convolutional neural

networks for hyperspectral image classification. Journal of Sensors 2015, 2015. 17. Dong, C.;

Loy, C. C.;

He, K.; Tang, X. In Learning a deep convolutional network for

image super-resolution, European conference on computer vision, Springer: 2014; pp 184199. 18. Dong, C.;

Loy, C. C.;

He, K. M.; Tang, X. O., Image Super-Resolution Using Deep

Convolutional Networks. Ieee T Pattern Anal 2016, 38 (2), 295-307. 19. Kim, J.;

Lee, J. K.; Lee, K. M., Accurate Image Super-Resolution Using Very Deep

Convolutional Networks. In Proc Cvpr Ieee, 2016; pp 1646-1654. 20. Kim, J.;

Lee, J. K.; Lee, K. M., Deeply-Recursive Convolutional Network for Image

Super-Resolution. In Proc Cvpr Ieee, 2016; pp 1637-1645. 21. Johnson, J.;

Alahi, A.; Fei-Fei, L. In Perceptual losses for real-time style transfer and

super-resolution, European Conference on Computer Vision, Springer: 2016; pp 694-711. 22. Ledig, C.; Aitken, A.;

Theis, L.;

Tejani, A.;

Huszar, F.;

Totz, J.;

Caballero, J.;

Cunningham, A.;

Acosta, A.;

Wang, Z. H.; Shi, W. Z., Photo-Realistic Single Image

Super-Resolution Using a Generative Adversarial Network. In 30th Ieee Conference on Computer Vision and Pattern Recognition (Cvpr 2017), 2017; pp 105-114. 23. Shi, W. Z.;

Caballero, J.;

Huszar, F.;

Totz, J.;

ACS Paragon Plus Environment 15

Aitken, A. P.;

Bishop, R.;

Analytical Chemistry 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510

Page 16 of 23

Rueckert, D.; Wang, Z. H., Real-Time Single Image and Video Super-Resolution Using an Efficient Sub-Pixel Convolutional Neural Network. In Proc Cvpr Ieee, 2016; pp 1874-1883. 24. Long, J.;

Shelhamer, E.; Darrell, T. In Fully convolutional networks for semantic

segmentation, Proceedings of the IEEE conference on computer vision and pattern recognition, 2015; pp 3431-3440. 25. Girshick, R.;

Donahue, J.;

Darrell, T.; Malik, J. In Rich feature hierarchies for

accurate object detection and semantic segmentation, Proceedings of the IEEE conference on computer vision and pattern recognition, 2014; pp 580-587. 26. Gӧrӧcs, Z.; K.;

Wu, Y.;

Tamamitsu, M.; Bianco, V.; Wolf, P.; Roy, S.; Shindo, K.; Yanny,

Koydemir, H. C.; Rivenson, Y., A deep learning-enabled portable imaging

flow cytometer for cost-effective, high-throughput, and label-free analysis of natural water samples. Light-Science & Applications.2018, 7 (1). 27. Rahmani, B.;

Loterie, D.;

Konstantinou, G.;

Psaltis, D.; Moser, C., Multimode

optical fiber transmission with a deep learning network. Light-Sci Appl 2018, 7. 28. Nair, V.; Hinton, G. E. In Rectified linear units improve restricted boltzmann machines, Proceedings of the 27th international conference on machine learning (ICML-10), 2010; pp 807-814. 29. Dreyfus, S. E., Artificial Neural Networks, Back Propagation, and the Kelley-Bryson Gradient Procedure. J Guid Control Dynam 1990, 13 (5), 926-928. 30. Kingma, D. P.; Ba, J., Adam: A method for stochastic optimization. In 3rd International Conference for Learning Representations, San Diego, 2015. 31. Byrd, R. H.;

Chin, G. M.;

Nocedal, J.; Wu, Y. C., Sample size selection in

optimization methods for machine learning. Math Program 2012, 134 (1), 127-155. 32. Li, M.;

Zhang, T.;

Chen, Y.; Smola, A. J. In Efficient mini-batch training for

stochastic optimization, Proceedings of the 20th ACM SIGKDD international conference on Knowledge discovery and data mining, ACM: 2014; pp 661-670. 33. Huang, C. K.;

Hamaguchi, H.; Shigeto, S., In vivo multimode Raman imaging reveals

concerted molecular composition and distribution changes during yeast cell cycle. Chem Commun 2011, 47 (33), 9423-9425. 34. Okuno, M.;

Kano, H.;

Leproux, P.;

Couderc, V.;

Day, J. P. R.;

Bonn, M.;

Hamaguchi, H., Quantitative CARS Molecular Fingerprinting of Single Living Cells with the Use of the Maximum Entropy Method. Angew Chem Int Edit 2010, 49 (38), 6773-6777.

ACS Paragon Plus Environment 16

Page 17 of 23 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Analytical Chemistry

278x190mm (150 x 150 DPI)

ACS Paragon Plus Environment

Analytical Chemistry 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

272x157mm (150 x 150 DPI)

ACS Paragon Plus Environment

Page 18 of 23

Page 19 of 23 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Analytical Chemistry

198x184mm (150 x 150 DPI)

ACS Paragon Plus Environment

Analytical Chemistry 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

176x210mm (150 x 150 DPI)

ACS Paragon Plus Environment

Page 20 of 23

Page 21 of 23 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Analytical Chemistry

264x195mm (150 x 150 DPI)

ACS Paragon Plus Environment

Analytical Chemistry 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

455x159mm (240 x 240 DPI)

ACS Paragon Plus Environment

Page 22 of 23

Page 23 of 23 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Analytical Chemistry

105x72mm (240 x 240 DPI)

ACS Paragon Plus Environment